Samsung PS50B550T2F User manual

Plasma TV user manual

BN68-02064A_Eng.indd 1

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at www.samsung.com/register

Model Serial No.

2009-09-18 �� 9:40:52

User Instructions

„

Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

„

Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

„

Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

„

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

„

Cell Defects

The PDP uses a panel consisting of 2,360,000 (HD-level) to 6,221,000 (FHD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

„

Avoid operating the TV at temperatures below 5°C(41°F)

„

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

„

Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

„

-

-

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

„

Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Digital TV (DVB-T) Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC) digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC) cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C is that for the broadcast transmission of digital TV over cable.

However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not included in this specification. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all providers.

6. For more information, please contact your local Samsung customer care centre.

© 2009 Samsung Electronics Co., Ltd. All rights reserved.

English - 2

BN68-02064A_Eng.indd 2 2009-09-18 �� 9:40:52

Contents

Connecting and Preparing Your TV

■

■

■

■

■

■

■

■

■

■

■

■

Checking Parts ..........................................................................4

Using the Stand-Base ...............................................................4

Assembling the Cables ..............................................................4

Viewing the Control Panel .........................................................5

Viewing the Connection Panel ...................................................6

Remote Control .........................................................................7

Installing Batteries in the Remote Control .................................8

Switching On and Off .................................................................8

Placing Your Television in Standby Mode ..................................8

Viewing the Menus ....................................................................9

Using the TOOLS Button ...........................................................9

Plug & Play Feature ................................................................10

Channel Control

■

■

Storing Channels ................................................................... 11

Managing Channels ................................................................13

Picture Control

■

■

■

Changing the Picture Settings .................................................15

Setting up the TV with your PC ...............................................18

PC Display ...............................................................................19

Sound Control

■

■

Changing the Sound Setting ...................................................20

Selecting the Sound Mode ......................................................21

Function Description

■

■

■

■

Configuring the Setup Menu ....................................................22

Setting the Time ......................................................................24

Source List / Edit Name ...........................................................25

Supported Program .................................................................26

Media Play

■

■

■

■

■

■

■

■

Connecting a USB Device .......................................................27

Using the Media Play Function

Using and Sorting Photo List

................................................28

...................................................29

Viewing a Photo or Slide Show

Using and Sorting the Music List

..............................................30

.............................................31

Playing a Music ......................................................................32

Picture / Music Settings Using Media Play ..............................33

Using the Setup Menu .............................................................33

About Anynet+

■

■

■

■

■

■

Connecting Anynet+ Devices

Setting Up Anynet+

..................................................34

.................................................................35

Scanning and Switching between Anynet+ Devices ................35

Recording ................................................................................36

Listening through a Receiver (Home theater)

Troubleshooting for Anynet

.........................37

+ ..................................................37

Recommendations for Use

■

■

■

■

■

■

■

■

■

Teletext Feature .......................................................................38

Wall Mount Kit Specifications (VESA) .....................................39

Preparing before installing Wall- Mount on the wall ................40

How to assemble the Stand-Base (depending on the model)

Securing the TV to the Wall

.40

.....................................................41

Securing the Installation Space ...............................................41

Troubleshooting .......................................................................42

Specifications ..........................................................................45

Software License .....................................................................46

BN68-02064A_Eng.indd 3

Symbol Press

N

Note

O

One-Touch Button

T

TOOLS

English - 3

2009-09-18 �� 9:40:53

Connecting and Preparing Your TV

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries (2ea)

Power Cord Cloth-Clean Holder-Ring (4ea)

(Refer to page 40)

Holder-Wire Cable

Screw (4ea)

(PS50B550 only)

Cover-Bottom

(PS50B550 only)

Cover-Bottom /

Screws (2ea)

(PS58B550 only)

Ferrite Core for

Power Cord

N

Ferrite Core (Power Cord, Headphone)

The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug as shown in the figure.

Ferrite Core fo

Headphone

Using the Stand-Base

N

N

Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and left directions.

-20° ~ 20°

Assembling the Cables

Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the transparent stand.

English - 4

BN68-02064A_Eng.indd 4 2009-09-18 �� 9:40:54

Viewing the Control Panel

N

The product colour and shape may vary depending on the model.

Front Panel buttons

Touch each button to operate.

1 SOURCE

Toggles between all the available input sources

( TV, AV1, AV2, Component1, Component2, PC, HDMI1,

HDMI2/DVI, HDMI3, HDMI4, USB).

N

In the on-screen menu, use this button as you would use the ENTERE button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3 + VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

4 < CH >

Press to change channels. In the on-screen menu, use the

< CH > buttons as you would use the ▲ and ▼ buttons on the remote control.

5 POWER INDICATOR

Lights up when the power is on.

6

( POWER)

Press to turn the TV on and off.

7

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

8 SPEAKERS

BN68-02064A_Eng.indd 5

English - 5

2009-09-18 �� 9:40:54

Viewing the Connection Panel

TV Rear Panel

1

9 or

Cable Television

Network

!

or

2 3 4 5 6 7 8 0 2

N

The product colour and shape may vary depending on the model.

N

N

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

When connecting an external device, match the colour of the connection terminal to the cable.

1 POWER IN

Connect the supplied power cord.

2 AV IN 1, 2 (AUDIO R/L / VIDEO)

Video and audio inputs for external devices, such as a camcorder or VCR.

3 PC IN (AUDIO / PC)

Connect to the video and audio output jack on your PC.

4 COMPONENT IN 1, 2

Audio (AUDIO L/R) and video (Y/P

B

/P

R

) inputs for Component.

5 HEADPHONES JACK

You can connect a set of headphones if you wish to watch a television programme without disturbing the other people in the room.

N

Prolonged use of headphones at a high volume may damage your hearing.

6 DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

7 SERVICE

Connector for service.

8 AUDIO OUT (AUDIO R/L)

Connect RCA audio signals from the TV to an external source, such as Audio equipment.

9 ANT IN

75Ω Coaxial connector for Aerial/Cable Network.

0 HDMI IN 1, 2(DVI), 3, 4

-

-

N

No additional Audio connection is needed for an HDMI to

HDMI connection.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 (DVI) jack.

What is HDMI?

High Definition Multimedia interface

-

allows the transmission of high definition digital video data and multiple channels of digital audio.

The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.

DVI AUDIO IN

DVI audio outputs for external devices.

!

USB

Connect a USB mass storage device to view photo files and play audio files.

Supported modes for HDMI/DVI and Component

HDMI/DVI 50Hz

HDMI/DVI 60Hz

Component

480i 480p 576i 576p 720p 1080i 1080p

X

X

O

X

O

O

X

X

O

O

X

O

O

O

O

O

O

O

O

O

O

English - 6

BN68-02064A_Eng.indd 6 2009-09-18 �� 9:40:57

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

N

The performance of the remote control may be affected by bright light.

1 POWER button

(turns the TV on and off)

2

Selects the TV mode directly.

3 Number buttons for direct channel access

4

Use to Select on-screen menu items

5 Temporary sound switch-off

6 Volume increase

Volume decrease

7

Available source selection

8 Channel control button

9 Use to quickly select frequently used functions.

0 Control the cursor in the menu

!

Use to see information on the current broadcast

@ Use these buttons in the Channel list, etc.

$

Sound mode selection

% Use these buttons in the Channel list, and Anynet+.

^

Previous channel

& Next channel

Previous channel

*

Displays the main on-screen menu

( Press to switch to your Favourite channels.

)

Returns to the previous menu a Exit the on-screen menu b This function enables you to view and play photo, music and movie files from an external device. (Refer to pages 29

(Photo), 31 (Music)) c Picture size selection d Digital subtitle display e Electronic Program Guide (EPG) display

Teletext Functions

2 Exit from the teletext display

(depending on the model)

7

Teletext mode selection (LIST/FLOF)

8 Teletext store

9 Teletext size

!

Teletext reveal

@

Fastext topic selection

# Teletext display/mix both

teletext information and the normal broadcast

^ Teletext sub page

& P :Teletext next page

P :Teletext previous page

* Teletext index

) Teletext hold a

Teletext cancel

English - 7

BN68-02064A_Eng.indd 7 2009-09-18 �� 9:40:57

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

N

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside the compartment.

3. Close the cover.

N

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

N

If the remote control doesn’t work, check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

N

The standby indicator lights up on your set.

2. Press the POWERP button on your set.

N

Yo u also can press the POWERP button or the TV button on the remote control to turn the TV on.

The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.

N

When you switch the set on for the very first time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWERP button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1. Press the POWERP button on the remote control.

N

T he screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button again.

N

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.

English - 8

BN68-02064A_Eng.indd 8 2009-09-18 �� 9:40:58

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,

Application, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTERE button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

N

The on-screen menus disappear from the screen after about one minute.

Mode

Cell Light

Contrast

Brightness

Sharpness

Colour

Tint (G/R)

Advanced Settings

: Standard

: 7

: 95

: 45

: 50

: 50

: G50/R50

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTERE button.

3. Press the ▲ / ▼ / ◄ / ► / ENTERE buttons to display, change, or use the selected items. For a more detailed description of each function, refer to the corresponding page.

Tools

•

•

•

•

•

Anynet+ (HDMI-CEC), see page 35

•

• Picture Mode, see page 15

Sound Mode, see page 20

Sleep Timer, see page 24

SRS TS HD, see page 20

Energy Saving, see page 23

Add to Favourite (or Delete from Favourite), see page 13

Auto Adjus tment, see page 18

Anynet+ (HDMI-CEC)

Picture Mode : Standard

Sound Mode

Sleep Timer

:

:

Custom

Off

SRS TS HD

Energy Saving

Add to Favourite

:

:

Off

Off

U Move E Enter e Exit

BN68-02064A_Eng.indd 9

English - 9

2009-09-18 �� 9:40:58

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

N

N

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

The Screen Saver is activated if there is no operating signal for longer than 15 minutes.

1. Press the POWER button on the remote control. The message Select 'Home Use'

when installing this TV in your home. is displayed.

Plug & Play

2. Then press the ◄ or ► button to select Store Demo or Home Use, then the

ENTERE button.

Select 'Home Use' when installing this TV in your home.

Store Demo Home Use

N

N

N

We recommend setting the TV to Home Use mode for the best picture in your home environment.

Store Demo mode is only intended for use in retail environments.

If the unit is accidentally set to

L Move E Enter

Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

N

The factory default setting for the picture will be Standard. Standard mode is the recommended home viewing picture mode.

3. Press the ENTERE button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to confirm your choice.

4. Press the ▲ or ▼ button to select the Antenna source to memorize. Press the ENTERE button to select Start.

•

•

•

Digital & Analogue : Digital and Analogue channels.

Digital : Digital channels.

Analogue : Analogue channels.

The channel search will start and end automatically.

N

N

N

Pr ess the ENTERE button at any time to interrupt the memorization process.

A fter all the available channels are stored, the message Set the Clock Mode. is displayed.

5. Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.

N

N

If you select Manual, Set current date and time is displayed. (refer to page 24)

If you have received a digital signal, the time will be set automatically. If not, see page 24 to set the clock.

6. Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the map of the Australia). Press the ENTERE button.

7. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTERE button.

N

N

You can change previous or next page by pressing the ◄ or ► button.

Th is menu is available HD Connection Guide in the Support menu.

8. The message Enjoy your TV. is displayed. When you have finished, press the ENTERE button.

If you want to return to this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTERE button.

2. Press the ENTERE button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is

‘0-0-0-0’.

N If you want to change PIN number, refer to 22 page.

N

N

The Plug & Play feature is only available in the TV mode.

Any previous settings and adjustments will remain including the picture mode.

All Channel settings will be lost.

For home viewing, ensure the picture mode is set to Standard.

Plug & Play

Time

Game Mode

Child Lock

Change PIN

Parental Lock

Subtitle

Teletext Language

: Off

: On

: ----

►

English - 10

BN68-02064A_Eng.indd 10 2009-09-18 �� 9:40:58

Channel Control

Storing Channels

❑

Country

You can change the desired country.

N

N

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’.

❑

•

N

•

•

N

N

N

Auto Store

Scans for all channels with active broadcast stations (and availability depends on your country) and stores them in the TV's memory.

You can memorize the Antenna source.

Digital & Analogue : Digital and Analogue channels.

Digital : Digital channels.

Analogue : Analogue channels.

If you want to stop Auto Store, press the ENTERE button.

The Stop Auto Store? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTERE button.

If a channel is locked using the Child Lock function, the PIN input window appears.

❑

Manual Store

Scans for a channel manually and stores it in the TV’s memory.

Country

Auto Store

Manual Store

Full Guide

Mini Guide

Default Guide

Channel List

: Australia

: Full Guide

„

Digital Channel (DTV)

Manual store for digital channels.

•

N

•

• Channel : Set the Channel number using the ▲, ▼ or number (

Frequency

Bandwidth

: Set the frequency using the number buttons.

: Set the bandwidth using the ▲, ▼ or number (

0~9) buttons.

0~9) buttons.

When it has finished, channels are updated in the channel list.

„

•

•

•

Analogue Channel

Manual store for analogue channel.

• Programme buttons.

(Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)

Colour System → Auto / PAL / SECAM / NTSC4.43

Sound System

: Sets the colour system value using the ▲ or ▼ button.

→ BG / DK / I / L : Sets the sound system value using the ▲ or ▼ button.

Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or

S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

N

N

You can also select the channel number directly by pressing the number ( 0~9) buttons.

If there is abnormal sound or no sound, reselect the sound standard required.

•

•

N

Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen.

Store (When you store the channel and associated programme number): Set to OK by pressing the ENTERE button.

Channel mode

C mode.

►

BN68-02064A_Eng.indd 11

English - 11

Continued...

2009-09-18 �� 9:40:59

❑

„

„

Full Guide / Mini Guide

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.

Full Guide : Displays the programme information as time ordered One hour segments. One hours of programme information is displayed which may be scrolled forwards or backwards in time.

Mini Guide : The information of each programme is displayed by each line on the current channel Mini Guide screen from the current programme onwards according to the programme starting time order.

❑

„

Default Guide

Mini Guide / Full Guide : You can decide whether to display either the Mini Guide or the Full Guide when the GUIDE button on the remote control is pressed.

O

You can also display the guide menu simply by pressing the GUIDE button.

Full Guide

Mini Guide

Default Guide

Channel List

Channel Mode

Fine Tune

: Full Guide

►

: Added Ch.

Using the Full / Mini Guide

Full Guide

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus

2:00 - 2:30

No Detailed Information

▼

Today

900 f tn

901 ITV Play

902 Kerrang!

903 Kiss

903 oneword

903 Smash Hits!

Watch

2:00 - 3:00

Freshmen O..

Mint Extra

Loaded

Street Hypn..

Fresh 40 with Dynamite MC

The Distillery

Smash Hits! Sunday

Information ◀◀ ▶▶ Page

No Information

No Information

Kisstory

No Information

„ Mini Guide „

3:00 - 4:00

+24 Hours „ Exit

Mini Guide

▼

2:00

2:30

5:00

DTV Cable 900 f tn

Freshmen On Campus

Street Hypnosis

Booze Britain

Watch Information ◀◀ ▶▶ Page „ Full Guide „ Exit

▲ / ▼ / ◄ / ►,

( ENTER)

RED

GREEN

YELLOW

BLUE

INFO

Select a programme by pressing the ▲/▼/◄/► button.

If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTERE button is pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the clock icon gone.

For details about scheduling programmes, refer to the section.

Toggle between the Mini Guide or Full Guide.

Full Guide: Scroll backwards quickly (-24 hours).

Mini Guide: Display previous page quickly.

Full Guide: Scroll forwards quickly (+24 hours).

Mini Guide: Display next page quickly.

Exit the guide.

INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video Quality

Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief summary of the highlighted programme are included on the detailed information. “…” will be appeared if the summary is long.

❑

Channel List

For the detailed procedures on using the Channel List, refer to the descriptions on pages 13~14.

❑

„

„

Channel Mode

When the P (< / >) button is pressed, Channels will be switched within the selected channel list.

Added Ch.

: Channels will be switched within the memorized channel list.

Favourite Ch.

: Channels will be switched within the favourite channel list.

❑

Fine Tune (only analogue channels)

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.

N

N

N

Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in the channel banner.

If you do not store the fine-tuned channel in memory, adjustments are not saved.

To reset the fine-tuning, select Reset by pressing the ▼ button and then press the ENTERE button.

English - 12

BN68-02064A_Eng.indd 12 2009-09-18 �� 9:41:00

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme guide for digital broadcasts.

N

Select a channel in the All Channels, Added Channels, Favourites, or Programmed screen by pressing the ▲ or ▼ buttons, and pressing the ENTERE button. Then you can watch the selected channel.

•

•

•

•

N

N

Mini Guide

Default Guide

Channel List

Channel Mode

All Channels : Shows all currently available channels.

Added Channels : Shows all added channels.

Favourites : Shows all favourite channels.

Programmed : Shows all current reserved programmes.

Using the Colour buttons with the Channel List

-

-

-

-

Red (

T

Channel Type

Green (

Yellow (

Zoom

): Toggle between your TV, Radio, Data / Other and All.

): Enlarges or shrinks a channel number.

Select ): Selects multiple channel lists.

TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Edit Channel

Number, Sort, Select All, (or Deselect All), or Auto Store menu.

(The Options menus may differ depending on the situation.)

Channel Status Display Icons

A An Analogue channel.

♥

A channel set as a Favourite.

\ A locked channel.

All

Fine Tune

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C --

A

3 ♥ C --

A

4 C --

A

5 C --

A

6 C --

A

7 C --

A

8 C --

„ Channel Type „ Zoom c A channel selected by pressing the yellow button.

( A programme currently being broadcast.

) A reserved programme

: Full Guide

: Added Ch.

„ Select Tools

❑

Channel List Tools Menu (in All Channels / Added Channels / Favourites)

N

N

Press the TOOLS button to use the tools menu.

Option menu items may differ depending on the channel status.

„

N

N

N

N

Add / Delete

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel to the same manner.

Added Channels or Favourite menu in the

„

Add to Favourite / Delete from Favourite

You can set channels you watch frequently as favourites.

All

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C --

A

3 C --

A

4 C --

A

5 C --

A

6 C --

A

7 C --

A

8 C --

„ Channel Type „ Zoom

Delete

Add to Favourite

Lock

Timer Viewing

Edit Channel Name

Sort

▼

„ Select Tools

T

Press the TOOLS button to display Tools menu.

You can also add the favourite channel by selecting Tools → Add to Favourite (or Delete from Favourite).

N

N

O

The “♥” symbol will be displayed and the channel will be set as a favourite.

All favourite channels will be shown on

To select the Favourite channels you have set up, press the remote control.

Favourite menu.

FAV.CH button on the

„ Lock / Unlock

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is set to On. (see page 22)

N

N

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting Change PIN from the menu.

N The “ \” symbol will be displayed and the channel will be locked.

„

Edit Channel Name (only analogue channel)

Channels can labeled so that their call letters appear whenever the channel is selected.

N The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Continued...

English - 13

BN68-02064A_Eng.indd 13 2009-09-18 �� 9:41:00

„

Edit Channel Number (only digital channel)

You can also edit the channel number by pressing the number buttons on the remote control.

„

Sort (only analogue channel)

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

„ Timer Viewing

If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List; even when you are watching another channel. To reserve a programme set the current time first. (See page 24)

N

N

N

Only memorized channels can be reserved.

You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control.

Reserving a programme will be shown on Programmed menu.

N Digital Programme Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.

You can reserve a programme according to the procedures described above.

„

Select All / Deselect All

•

•

N

N

N

Select All : You can select all the channels in the channel list.

Deselect Al l: You can deselect all the selected channels in the channel list.

You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple channels at the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The c mark appears to the left of the selected channels.

You can only select Deselect All when there is a selected channel.

„

Auto Store

N

N

For further details on setting up options, refer to page 11.

If a channel is locked using the Child Lock function, the PIN input window appears.

❑

Channel List Tools Menu (in Programmed)

You can view, modify or delete a reservation.

N

Press the TOOLS button to use the tools menu.

„

Change Info

Select to change a viewing reservation.

1 / 1 / 2009

13:59 5 TV1 Quincy, M.E

18:59 2

20:59 2

21:59 2

TV3 The Equalizer

TV3 McMillan & Wife

TV3 M.Spillane’s mike Hammer

„

Cancel Schedules

Select to cancel a viewing reservation.

„

Information

Select to view a viewing reservation. (You can also change the reservation information.)

„

Select All / Deselect All

You can select (or deselect) all channels in the channel list.

All „ Zoom „ Select Tools Information

BN68-02064A_Eng.indd 14

English - 14

2009-09-18 �� 9:41:00

Picture Control

Changing the Picture Settings

❑

❑

•

•

•

•

Mode

You can select the type of picture which best corresponds to your viewing requirements.

T

Dynamic : Selects the picture for high-definition in a bright room.

Standard : Selects the picture for the optimum display in a normal environment.

Eco : Selects the picture for optimum and eye-comfortable display.

Movie : Selects the picture for viewing movies in a dark room.

Press the TOOLS button to display Tools menu.

You can also set the picture mode by selecting Tools → Picture Mode.

Mode

Cell Light

Contrast

Brightness

Sharpness

Colour

Tint (G/R)

: Standard

: 7

: 95

: 45

: 50

: 50

: G50/R50

N

N

N

N

•

•

N

•

•

•

•

N

Advanced Settings

Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)

Your television has several setting options that allow you to control the picture quality.

Cell Light : Adjusts the pixel brightness.

Contrast : Adjusts the contrast level of the picture.

Brightness : Adjusts the brightness level of the picture.

Sharpness : Adjusts the edge definition of the picture.

Colour : Adjusts Colour saturation of the picture.

Tint (G/R) : Adjusts the Colour tint of the picture.

Select a picture mode to be adjusted first. The adjusted values are saved for each picture mode.

When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour, or Tint (G/R), the OSD will be adjusted accordingly.

In Analogue TV, Ext., AV modes of the PAL system, you cannot use the Tint Function.

In PC mode, you can only make changes to Cell Light, Contrast and Brightness.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and then this will reduce the overall running cost.

►

❑

Advanced Setting

You can adjust the detailed settings for your screen including the color and contrast.

N

N

Advanced Setting is available in Standard or Movie mode.

In PC mode, you can only make changes to Dynamic Contrast, Gamma and

White Balance from among the Advanced Setting items.

„

Black Tone → Off / Dark / Darker / Darkest

You can select the black level on the screen to adjust the screen depth.

Colour

Tint (G/R)

Advanced Setting

: 50

: G50/R50

Picture Options

Picture Reset

►

„

Dynamic Contrast → Off / Low / Medium / High

You can adjust the screen contrast so that the optimal contrast is provided.

„

Gamma

You can adjust the primary colour Intensity.

„

•

•

•

Colour Space

Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite colour space to experience the most natural colour.

Auto

Native

Custom

N

: Automatically sets the color range depending on the input video source.

: Sets the color range wider than the that of the input video source.

: Adjusts the color range to suit your preference.

Customizing the Colour Space

-

-

-

-

Colour

Red /

→ Red / Green / Blue / Yellow / Cyan / Magenta

Adjusts the Colour range to suit your preference.

Reset

Colour is available when Colour Space is set to Custom.

Green / Blue: In Colour, you can adjust the RGB values for the selected colour.

: Resets the colour space to the default values.

Continued...

English - 15

BN68-02064A_Eng.indd 15 2009-09-18 �� 9:41:01

„

White Balance

You can adjust the colour temperature for more natural picture colours.

•

• R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain

Reset

: Changing the adjustment value will refresh the adjusted screen.

: The previously adjusted white balance will be reset to the factory defaults.

„

Flesh Tone

You can adjust the flesh tone to be more or less red.

N

Changing the adjustment value will refresh the adjusted screen.

„

Edge Enhancement → Off / On

You can emphasize object boundaries in the picture.

„

❑ xvYCC → Off / On

Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).

N

N xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.

This function may not be supported depending on your external device.

Tint (G/R) : G50/R50

Picture Options

You can customize the additional picture settings to suit your preference.

Advanced Setting

Picture Options

N

In PC mode, you can only make changes to the Colour Tone, Size and Screen

Burn Protection from among the items in Picture Options.

Picture Reset

►

„

Colour Tone → Cool / Normal / Warm1 / Warm2 / Warm3

You can select the most comfortable colour tone to your eyes.

N

N

The adjusted values are stored according to the selected Picture mode.

Warm1 , Warm2, or Warm3 is only activated when the picture mode is Movie.

„

Size

You can select the picture size which best corresponds to your viewing requirements.

•

•

•

•

•

16:9

4:3

: Sets the picture to the 16:9 aspect ratio.

Wide Zoom

Zoom

: Magnify the size of the picture more than 4:3.

: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.

: Sets the picture to the 4:3 aspect ration.

Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or Component

O

(1080i/1080p) signals are input.

N The picture size options may vary depending on the input source.

N

N

N

N

N

The items available may differ depending on the selected mode.

In PC Mode, only 16:9 and 4:3 mode can be adjusted.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Temporary image retention may occur when viewing a static image on the set for more than two hours.

After selecting Wide Zoom mode: Press the ► button to select Position, then press the ENTERE button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button.

N

N

After selecting Zoom mode: Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼ button to move the picture up and down. Then press the ENTERE button. Press the ► button to select Size, then press the ENTERE button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the

ENTERE button.

After selecting Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.

N

N

Reset : Press the ◄ or ► button to select Reset, then press the ENTERE button. You can initialize the setting.

If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan function.

You can select these options simply by pressing the P.SIZE button on the remote control.

„

Digital NR → Off / Low / Medium / High / Auto

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.

N

When the signal is weak, select one of the other options until the best picture is displayed.

Continued...

English - 16

BN68-02064A_Eng.indd 16 2009-09-18 �� 9:41:01

„

HDMI Black Level → Normal / Low

You can directly select the black level on the screen to adjust the screen depth.

N

This function is active only when the external input connects to HDMI (RGB signals).

„

1080 Full HD Motion Demo → Off / On

Samsung' new generation PDP panels deliver stunning Full HD motion clarity when viewing fast action sports, movies, and games.

N

This function is not available in PC, Game, or Media Play mode.

„

„

Film Mode

You can optimize the picture mode for watching movies.

•

•

• Off : Turn the film mode function off.

Auto1 : Automatically adjusts the picture for the best quality when watching a film.

N

N

Auto2 : Automatically optimizes the video text when watching a film.

Film Mode is supported in TV, AV, COMPONENT(480i/1080i) and HDMI(480i/1080i).

Film Mode is not supported in DTV channel with resolution 576p/720p.

Blue Only Mode → Off / On

This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Color and Tint of video equipment such as DVD players, Home Theaters, etc.

N Blue Only Mode is available when the picture mode is set to Movie or Standard.

„

Screen Burn Protection

Configures the Screen Burn Protection Options to prevent and reduce pixel burn.

When an image remains in one position too long, it may cause a permanent burn on the screen.

• Pixel Shift : To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to program the time between movement of the picture in minutes.

N

N

N

N

Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.

Select the required option by pressing the ▲ or ▼ button, then press the ENTERE button.

Available options: Horizontal, Vertical, Time.

Optimum condition for pixel shift

Horizontal

Vertical

Time (minute)

Item

0~4

0~4

1~4 min

TV/Ext/AV/Component/HDMI/PC

2

4

2 min

•

•

N

N

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

This function is not available in the Screen Fit mode.

Scrolling : This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.

Side Grey : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides.

Light : When you set the screen ratio to 4:3, it brightens the left and right sides.

Dark : When you set the screen ratio to 4:3, it darkens the left and right sides.

❑

Picture Reset → Reset Picture Mode / Cancel

Resets all picture settings to the default values.

N

Select a picture mode to be reset. The reset is performed for each picture mode.

Advanced Setting

Picture Options

Picture Reset

►

English - 17

BN68-02064A_Eng.indd 17 2009-09-18 �� 9:41:01

Setting up the TV with your PC

N Preset: Press the SOURCE button to select PC mode.

❑

Auto Adjustment

Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and position are adjusted automatically.

N This function does not work in DVI-HDMI mode.

T Press the TOOLS button to display Tools menu.

You can also set the adjustment by selecting Tools → Auto Adjustment.

Brightness

Sharpness

Auto Adjustment

: 45

: 50

Screen

Advanced Setting

Picture Options

Picture Reset

❑

„

„

„

„

Screen

Coarse

Adjusts the frequency when vertical noise appears on the screen.

Fine

Adjusts the screen to be clearer.

PC Position

Adjust the PC’s screen positioning if it does not fit the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position.

Image Reset

You can replace all image settings with the factory default values.

►

BN68-02064A_Eng.indd 18

English - 18

2009-09-18 �� 9:41:01

PC Display

❑

Setting Up Your PC Software (Based on Windows XP)

The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

1. First, click on ‘Control Panel’ on the Windows start menu.

2. When the control panel window appears, click on ‘Appearance and Themes’ and a display dialog-box will appear.

3. When the control panel window appears, click on ‘Display’ and a display dialog-box will appear.

4. Navigate to the ‘Settings’ tab on the display dialog-box.

The correct size setting (resolution)

Optimum: 1920 X 1080 pixels

If a vertical-frequency option exists on your display settings dialog box, the correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.

❑

Display Modes

Both screen position and size will vary depending on the type of PC monitor and its resolution.

The resolutions in the table are recommended.

„

D-Sub and HDMI/DVI Input

Mode

IBM

MAC

VESA CVT

VESA DMT

VESA GTF

Resolution

640 x 350

720 x 400

640 x 480

832 x 624

1152 x 870

720 x 576

1152 x 864

1280 x 720

1280 x 720

1280 x 960

640 x 480

640 x 480

640 x 480

800 x 600

800 x 600

800 x 600

1024 x 768

1024 x 768

1024 x 768

1152 x 864

1280 x 800

1280 x 800

1280 x 960

1280 x 1024

1280 x 1024

1360 x 768

1440 x 900

1440 x 900

1680 x 1050

1280 x 720

1280 x 1024

VESA DMT /

DTV CEA

1920 x 1080p

Horizontal Frequency (kHz)

31.469

31.469

35.000

49.726

68.681

35.910

53.783

44.772

56.456

75.231

60.023

67.500

49.702

62.795

60.000

63.981

79.976

47.712

31.469

37.861

37.500

37.879

48.077

46.875

48.363

56.476

55.935

70.635

65.290

52.500

74.620

67.500

Vertical Frequency (Hz)

70.086

70.087

66.667

74.551

75.062

59.950

59.959

59.855

74.777

74.857

75.029

75.000

59.810

74.934

60.000

60.020

75.025

60.015

59.940

72.809

75.000

60.317

72.188

75.000

60.004

70.069

59.887

74.984

59.954

70.000

70.000

60.000

N

N

N

When using an HDMI / DVI cable connection, you must use the HDMI IN 2 (DVI) jack.

The interlace mode is not supported.

The set might operate abnormally if a non-standard video format is selected.

Pixel Clock Frequency (MHz)

25.175

28.322

30.240

57.284

100.000

32.750

81.750

74.500

95.750

130.000

25.175

31.500

31.500

40.000

50.000

49.500

65.000

75.000

78.750

108.000

83.500

106.500

108.000

108.000

135.000

85.500

106.500

136.750

146.250

89.040

128.943

148.500

Sync Polarity (H/V)

+ / -

- / +

- / -

- / -

- / +

- / +

- / +

- / +

- / +

- / +

+ / +

+ / +

- / +

- / +

+ / +

+ / +

+ / +

+ / +

- / -

- / -

- / -

+ / +

+ / +

+ / +

- / -

- / -

- / +

- / +

- / +

- / +

- / -

+ / +

English - 19

BN68-02064A_Eng.indd 19 2009-09-18 �� 9:41:02

Sound Control

Changing the Sound Setting

❑

❑

Mode → Standard / Music / Movie / Clear Voice / Custom

You can select the type of special sound effect to be used when watching a given broadcast.

Mode : Custom

T

Press the TOOLS button to display Tools menu.

You can also configure the sound mode by selecting Tools → Sound Mode.

Equalizer

SRS TruSurround HD : Off

Audio Language : ----

Audio Format

Audio Description

: ----

Equalizer

•

•

•

•

The sound settings can be adjusted to suit your personal preferences.

Mode : You can select a sound mode to suit your personal preferences.

Balance : Controls the balance between the right and left speakers.

Auto Volume

Speaker Select

: Off

: TV Speaker

100Hz / 300Hz / 1 KHz / 3KHz / 10KHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies.

Reset : Resets the equalizer settings to the default values.

❑

SRS TruSurround HD → Off / On

SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass.

SRS TruSurround HD is down mixing technology that makes the Surround Sound effect of virtual 5.1 channel via two speakers.

This function provide not only rich deep bass at a low-pitched sound but also improve the resolution at a high-pitched sound.

T

Press the TOOLS button to display Tools menu.

You can also set the SRS TruSurround HD by selecting Tools → SRS TS HD.

►

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc.

TruSurround HD technology is incorporated under license from SRS Labs, Inc.

❑

Audio Language (only digital channel)

You can change the default value for audio languages. Displays the language information for the incoming stream.

N

You can only select the language among the actual languages being broadcast.

❑

Audio Format → MPEG / Dolby Digital (only digital channel)

When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.

N

You can only select the language among the actual languages being broadcast.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

❑

Audio Description (only digital channel)

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the

Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the

Audio Description On or Off and control the volume.

„

Audio Description → Off / On

Turn the audio description function on or off.

„

Volume

You can adjust the audio description volume.

N Volume is active when Audio Description is set to On.

Continued...

English - 20

BN68-02064A_Eng.indd 20 2009-09-18 �� 9:41:02

❑

Auto Volume → Off / On

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

❑

Speaker Select → External Speaker / TV Speaker

If you want to hear the sound through separate speakers, cancel the internal amplifier.

N

N

The –

If you select

+, M MUTE buttons do not operate when the Speaker Select is set to External Speaker.

External Speaker in the Speaker Select menu, the sound settings will be limited.

TV Speaker

External Speaker

Video No Signal

TV's Internal Speakers

TV / AV / Component / PC / HDMI

Speaker Output

Mute

Mute

Audio Out (Optical, L / R Out) to Sound System

TV / AV / Component / PC / HDMI

Sound Output

Sound Output

Mute

❑

Sound Reset → Reset All / Reset Sound Mode / Cancel

You can restore the Sound settings to the factory defaults.

Auto Volume

Speaker Select

Sound Reset

: Off

: TV Speaker

►

Selecting the Sound Mode

When you set to Dual l ll, the current sound mode is displayed on the screen.

Type of broadcast

Regular broadcast

(Standard audio)

Regular + NICAM Mono

NICAM

Stereo

NICAM-Stereo

NICAM

NICAM

Stereo

NICAM Dual-I/II

NICAM

Dual-1

A2

Stereo

Regular broadcast

(Standard audio)

Bilingual or DUAL-I/II

Stereo

Dual I

Stereo

On-screen indication

Mono (Normal use)

NICAM

Dual-2

Mono (Normal use)

N

N

N

O

If the stereo signal is weak and an automatic switching occurs, then switch to the mono.

This function is only activated in stereo sound signal. It is deactivated in mono sound signal.

This function is only available in TV mode.

You can select these options simply by pressing the DUAL button on the remote control.

Mono

(Normal)

Mono

(Normal)

Mono

(Normal)

Dual II

Mono

(Forced mono)

English - 21

BN68-02064A_Eng.indd 21 2009-09-18 �� 9:41:02

Function Description

Configuring the Setup Menu

❑

„

Game Mode

When connecting to a game console such as PlayStation TM or Xbox more realistic gaming experience by selecting the game menu.

TM , you can enjoy a

Plug & Play

Time

Game Mode

N

N

N

N

N

N

When the Game Mode is On

•

•

• Picture Mode mode.

Sound Mode

is automatically changed to Standard and users cannot change the

is automatically changed to Custom and users cannot change the mode. Adjust the sound using the equalizer.

The Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting.

Child Lock

Change PIN

Parental Lock

Subtitle

Teletext Language

Preference

Melody

Game Mode is not available in regular TV mode or Game Mode set to Off.

If the picture is poor when external device is connected to TV, check if Game Mode is On.

This function supports only game function.

If you display the TV menu in Game mode, the screen shakes slightly.

The mark ( ) appears on the screen which means that Game Mode is on with the selected source.

Game mode is not available in PC mode.

: Off

: On

: - - - -

: Medium

►

❑

N

N

N

N

Child Lock → Off / On

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.

You can lock some channels in Channel List. (refer to page 13)

Child Lock is available only in TV mode.

❑

N

N

N

Change PIN

You can change your personal ID number that is required to set up the TV.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’.

If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to

POWER (Off), MMUTE, 8, 2, 4, POWER (On).

‘0-0-0-0’:

❑

N

N

N

N

Parental Lock

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit PIN

(Personal Identification Number) code that is defined by the user.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is

When the parental ratings are set, the “

‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.

\ ” symbol is displayed.

Allow All : Press to unlock all TV ratings.

Block All: Press to lock all TV ratings.

❑

•

N

•

•

Subtitle

You can activate and deactivate the subtitles. Use this menu to set the Subtitle Mode. Normal under the menu is the basic subtitle and Hard of hearing is the subtitle for a hearing-impaired person.

N

O

Subtitle → Off / On: Switches subtitles off or on.

Mode → Normal / Hard of hearing: Sets the subtitle mode.

Subtitle Language : Set the subtitle language.

If the programme you are watching does not support the Hard of hearing function, Normal automatically activates even though

Hard of hearing mode is selected.

English is the default in cases where the selected language is unavailable in the broadcast.

You can select these options simply by pressing the SUBT. button on the remote control.

Continued...

English - 22

BN68-02064A_Eng.indd 22 2009-09-18 �� 9:41:03

❑

Teletext Language

You can set the Teletext language by selecting the language type.

N

English is the default in cases where the selected language is unavailable in the broadcast.

❑

„

Preference

Primary Audio Language / Secondary Audio Language / Primary Subtitle Language / Secondary Subtitle Language /

Primary Teletext Language / Secondary Teletext Language

Using this feature, users can select one of the languages. The language selected here is the default when the user selects a channel.

If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language menu are automatically changed to the selected language.

The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a list of languages supported by the current channel and the selection is highlighted. If you change this language setting, the new selection is only valid for the current channel. The changed setting does not change the setting of the Primary Subtitle Language, Primary Audio Language, or the Primary Teletext Language of the Preference menu.

❑

Digital Text → Disable / Enable (Not available in all locations)

If the programme is broadcast with digital text, this feature is enabled.

N MHEG ( Multimedia and Hypermedia Information Coding Experts Group)

An International standard for data encoding systems used in multimedia and hypermedia. This is at a higher level than the MPEG system which includes data-linking hypermedia such as still images, character service, animation, graphic and video files as well as multimedia data. MHEG is user runtime interaction technology and is being applied to various fields including VOD (Video-On-

Demand), ITV (Interactive TV), EC (Electronic Commerce), tele-education, tele-conferencing, digital libraries and network games.

❑

Melody → Off / Low / Medium / High

The TV power on / off melody sound can be adjusted.

N

The Melody does not play

-

-

-

When no sound is output from the TV because the MMUTE button has been pressed.

When no sound is output from the TV because the

When the TV is turned off by Sleep Timer function.

– (Volume) button has been pressed.

Teletext Language

Preference

Digital Text

Melody

Energy Saving

: - - - -

: Disable

: Medium

: Off

❑

Energy Saving

This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the

Energy Saving mode option to High to reduce eye fatigue as well as power consumption.

•

•

•

• Off : Turns off the energy saving function.

Low : Sets the TV to low energy saving mode.

Medium

High

: Sets the TV to medium energy saving mode.

: Sets the TV to high energy saving mode.

T Press the TOOLS button to display Tools menu.

You can also set the energy saving option by selecting Tools → Energy Saving.

►

BN68-02064A_Eng.indd 23

English - 23

2009-09-18 �� 9:41:03

Setting the Time

❑

Clock

Setting the clock is necessary in order to use the various timer features of the TV.

N

N

The current time will appear every time you press the INFO button.

If you disconnect the power cord, you have to set the clock again.

„

Clock Mode

You can set up the current time manually or automatically.

•

• Auto : Set the current time automatically using the time from the digital broadcast.

Manual : Set the current time to a manually specified time.

Plug & Play

Time

Game Mode

Child Lock

Change PIN

Parental Lock

: Off

: On

Subtitle

Teletext Language : - - - -

Preference

►

„

Clock Set

You can set the current time manually.

N

N

Set up this item when you have set Clock Mode to Manual.

You can set the Day, Month, Year, Hour, Minute directly by pressing the number buttons on the remote control.

Clock Mode

Clock Set

Time Zone

Clock

: Auto ►

„ Time Zone

You can select your time zone.

N

N

N

U Move E Enter R Return

This function is only available when Clock Mode is set to Auto.

Depending on the broadcast station and signal, the auto time may not be set correctly. If this occurs, set the time manually.

The Antenna or cable must be connected in order to set the time automatically.

❑

Sleep Timer → Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min

The sleep timer automatically shuts off the TV after a preset time.

N

N

The TV automatically switches to standby mode when the timer reaches 0.

To cancel the Sleep Timer function, select Off.

T Press the TOOLS button to display Tools menu.

You can also set the sleep timer by selecting Tools → Sleep Timer.

❑

N

N

Timer 1 / Timer 2 / Timer 3

Three different on / off timer settings can be made.

•

•

•

• On Time : Set the hour, minute, and Activate / Inactivate.

(To activate timer with the setting you’ve chosen, set to Activate.)

Off Time : Set the hour, minute, and Activate / Inactivate.

(To activate timer with the setting you’ve chosen, set to Activate.)

Volume : Set the required volume level.

Source : Selects TV or USB device.

N

When you select the TV, you can set the Antenna and Channel.

-

Antenna

Channel

: Select ATV or DTV.

: Select the desired channel.

N

When you select the USB, you can set the Contents.

Contents : Selects the desired contents on the USB.

• Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun, or Manual.

N

When Manual is selected, press the ► button to select the desired day of the week. Press the ENTERE button over the

N desired day and the c mark will appear.

You must set the clock first.

You can set the hour, minute by pressing the number buttons on the remote control.

Auto Power Off

When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is on for too long time.

English - 24

BN68-02064A_Eng.indd 24 2009-09-18 �� 9:41:03

Source List / Edit Name

❑

„

Source List

Use to select TV or other external input sources such as DVD players or Cable Box /

Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.

TV , AV1, AV2, Component1, Component2, PC, HDMI1, HDMI2/DVI, HDMI3,

HDMI4, USB.

N

N

N

O

You can choose only those external devices that are connected to the TV. In the

Source List, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.

PC always stays activated.

Using the Colour buttons on the remote with the Source list

(Refresh): Refreshes the connecting external devices.

Red

T

Press the SOURCE button on the remote control to view an external signal source.

TV mode can be selected by pressing the TV button, number buttons (0~9), and the

P < / > button on the remote control.

Source List

Edit Name

❑

„

Edit Name

VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI / DVI PC / TV / IPTV /

Blu-ray / HD DVD / DMA

You can name the device connected to the input jacks to make your input source selection easier.

N

N

When a PC with a resolution of 1920x1080@60Hz is connected to the HDMI IN 2 (DVI) port, you should set the HDMI2/DVI mode to PC in the Edit Name of the Input mode.

When connecting an HDMI/DVI cable to the HDMI IN 2(DVI) port, you should set the HDMI2/DVI mode to DVI or DVI PC in the

Edit Name of the Input mode. In this case, a separate sound connection is required.

BN68-02064A_Eng.indd 25

English - 25

2009-09-18 �� 9:41:03

Supported Program

❑

„

Self Diagnosis

Picture Test

If you think you have a picture problem, perform the picture test. Check the color pattern on the screen to see if the problem still exists.

N

•

•

Does the problem still exist with this test photo?

appears on the screen.If the test pattern does not appear or there is noise in the test pattern, select Yes. If the test pattern is properly displayed, select No.

Yes

No

: There may be a problem with the TV. Contact Samsung’s Call Center for assistance.

: There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to the external device’s user manual.

„

Sound Test

If you think you have a sound problem, please perform the sound test.You can check the sound by playing a built-in melody sound through the TV.

N

•

• : There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to

N

Does the problem still exist with this sound test?

appears on the screen.If during the sound test you can hear sound only from one speaker or not at all, select Yes. If you can hear sound from the speakers, select No.

Yes

No

: There may be a problem with the TV. Contact Samsung’s Call Center for assistance.

the external device’s user manual.

If you hear no sound from the TV’s speakers, before performing the sound test, make sure Speaker Select is set to TV speaker

N in the Sound menu.

The melody will be heard during the test even if the MMUTE button.

Speaker Select is set to External Speaker or the sound is muted by pressing

„

❑

„

Signal Strength (Digital channels only)

You can adjust your antenna to improve the reception of available digital channels.

N

If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.

Continue to adjust the antenna until you fi nd the best position with the strongest signal.

Software Upgrade

To keep your product up-to-date with new Digital Television features then software upgrades are periodically broadcast as part of the normal Television signal. It will automatically detect these signals and display the software upgrade banner. You are given the option to install the upgrade.

TV Side Panel

USB Drive

By USB

Insert a USB drive containing the fi rmware upgrade into TV. Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the fi rmware upgrade. Please check the fi rmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default

(factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.

„ By Channel

Upgrades the software using the broadcasting signal.

„

Standby Mode Upgrade

To continue software upgrade with master power on, select on by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is automatically conducted. Since the power of the unit is turned on internally, the screen may be on slightly for the product. This phenomenon may continue for more than 1 hour until the software upgrade is completed.

„ Alternative Software

Replace the current software with the alternative.

❑

❑

HD Connection Guide

The brief instruction on How to get the best performance from your HD TV is displayed. We offer the connection method for HD devices.

N

You can change previous or next page by pressing the ◄ or ► button.

Contact Samsung

You can know the Samsung Call center, website and information for product.

English - 26

BN68-02064A_Eng.indd 26 2009-09-18 �� 9:41:04

Media Play

Connecting a USB Device

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

N

1. Press the POWER button to turn the TV on.

2. Connect a USB device containing photo, music and movie fi les to the USB jack on the side of the TV.

N

N

N

TV Side Panel

USB Drive

If you enter the Media Play mode with no USB device connected the message No external

storage device found. Check the connection status. will appear. In this case, insert the USB device, exit the screen by pressing the MEDIA.P button on the remote control and enter the

Media Play screen again.

Media Play only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage

Class Bulk-Only Transport device. Examples of MSC are Thumb drives and Flash Card

Readers (Both USB HDD and HUB are not supported.)

MTP (Media Transfer Protocol) is not supported.

The fi le system only supports FAT16/32 (The NTFS fi le system is not supported).

Certain types of USB Digital camera and audio devices may not be compatible with this TV.

Please connect directly to the USB port of your TV. If you are using a separate cable connection, there may be a USB compatibility problem.

Before connecting your device to the TV, please back up your fi les to prevent them from damage or loss of data. SAMSUNG is not responsible for any data fi le damage or data loss.

Do not disconnect the USB device while it is loading.

MSC supports MP3 and JPEG fi les, while a PTP device supports JPEG fi les only.

The sequential JPEG format is supported.

The higher the resolution of the image, the longer it takes to display on the screen.

The maximum supported JPEG resolution is 15360X8640 pixels.

For unsupported or corrupted fi les, the Not Supported File Format message is displayed.

If the number of photo fi les exceeds 4000 (or the number of music fi les exceeds 3000), any fi les exceeding the 4000 limit may not be displayed in the Photo List (or Music List).

MP3 fi les with DRM that have been downloaded from a non-free site cannot be played.

MP3 fi les with DRM downloaded from pay sites are not played.

DRM(Digital Rights Management) prevents illegal uses of digital media for copyright protection.

When moving to a photo, loading may take a few seconds. At this point, the loading icon will appear at the screen.

BN68-02064A_Eng.indd 27

English - 27

2009-09-18 �� 9:41:04

Using the Media Play Function

This function enables you to view and listen to photo, music and movie files saved on a USB Mass Storage Class (MSC) device.

It might not work properly with unlicensed multimedia files.

❑

Entering the Media Play Menu

1. Press the MENU button. Press the ▲ or ▼ button to select Application, then press the ENTER E button.

2. Press the ▲ or ▼ button to select Media Play (USB), then press the ENTER E button.

N

N

N

The Media Play menu is displayed.

Press the SOURCE button on the remote control repeatedly to select USB, then press the ENTER E button.

Press the MEDIA.P button on the remote control to display the Media Play menu.

3. Press the Red button, then press the ▲ or ▼ button to select the corresponding

USB Memory Device (i.e. if connected through a hub). Press the ENTER

E button.

N

This function differs depending on the USB Memory

N

Device connected to TV.

The selected USB device name appears at the bottom left of the screen.

4. Press the ◄ or ► button to select an icon (Photo, Music, Setup), then press the ENTER

E

button.

N

To exit Media Play mode, press the MEDIA.P button on the remote control.

Media Play

Photo

USB „ Device

USB : USB name

PHOTO

Music

148.48MB/995.00MB Free

Setup

R Return

❑

Removing a USB Memory Device Safely

You can remove the device safely from the TV.

1. Press the TOOLS button in the Media Play file list screen, or while a SlideShow or music file is being played.

2. Press the ▲ or ▼ button to select Remove Safely, then press the ENTER

E button.

3. Remove the USB device from the TV.

❑

Screen Display

IMG_0345.

JPG

IMG_0346.

JPG

IMG_0349.

JPG

USB

USB „ Device

1

1

IMG_0335.JPG

4/6 Slide Show

Play Current Group

Information

Remove Safely

Select

T

Tools R Return

2

1

1

1

1/67 c

▶ ◀

IMG_03496.

JPG

IMG_03496.

JPG

IMG_0335.JPG

IMG_0343.

JPG

IMG_03496.

JPG

USB

3 5

USB „ Device

4 1File(s) Selected

Select

T

Tools R Return

1. Currently selected file: The currently selected file is highlighted.

2. View Groups: The sorting group including the currently selected photo is highlighted.

3. Current Device: Shows the currently selected device name.

4. Item Selection Information: Shows the number of photos that are selected by pressing the Yellow button.

5. Help Items

•

• Red ( Device) button: Selects a connected device.

Yellow ( Select) button: Selects file from the file list. Selected files are marked with a symbol c. Press the yellow button again to cancel a file selection.

• TOOLS (Tools) button: Displays the option menus. (The tools menu changes according to the current status.)

• R Return (Return) button: Return to previous menu.

English - 28

BN68-02064A_Eng.indd 28 2009-09-18 �� 9:41:08

❑

Using the Remote Control Button in Media Play Menu

Button

▲/▼/◄/►

ENTER

E

RETURN

TOOLS

INFO

MEDIA.P

P /

EXIT

Operations

Move the cursor and select an item.

Select the currently selected item.

Play or pause the files while playing the slide show or music files.

Play or pause the Slide Show or Music file.

Return to the previous menu.

Run various functions from the Photo, Music and Movie menus.

Stop the current slide show, Music or Movie file.

Show file information.

Exit Media Play mode.

Stop Media Play mode and Returns to TV mode.

Stop the current function and return to the Media Play main menu.

Using and Sorting Photo List

You can sort photos in the Photo List by a particular standard.

1. Press the MEDIA.P button on the remote control to display the Media Play menu.

2. Press the ◄ or ► button to select Photo, then press the ENTER E button.

3. Press the (Play)/ ENTER

E

button to start the Slide Show in the order selected by the user.

N

N

N

The information of a photo file is automatically set.

Photos for which information cannot be displayed are set as

PTP does not support folder sort mode.

Unclassified.

❑

„

„

Photo List Tools Menu

Slide Show

You can play a Slide Show using the photo files on the USB memory device.

Play Current Group

You can play a Slide Show using only the photo files in the currently selected sorting group.

„

Information

The photo file information including the name, the size, the resolution, the date modified and the path is displayed.

N

O

You can view the information of photo files during a Slide Show using the same procedures.

Alternatively, select a photo from the photo list and press the INFO button to view the information.

„

Remove Safely

You can remove the device safely from the TV.

1

1

▶

IMG_03496.

JPG IMG_03496.

JPG

USB

USB „ Device

IMG_0335.JPG

1/67

◀

IMG_0343.

JPG

IMG_03496.

JPG

Select

T

Tools R Return

IMG_0345.

JPG

IMG_0346.

JPG

IMG_0349.

JPG

USB

USB „ Device

1

1

IMG_0335.JPG

4/6 Slide Show

Play Current Group

Information

Remove Safely

Select

T

Tools R Return

English - 29

BN68-02064A_Eng.indd 29 2009-09-18 �� 9:41:11

Viewing a Photo or Slide Show

❑

N

N

N

Viewing a Slide Show

1. Press the ◄ or ► button to select the desired photo in the Photo list.

2. Press the TOOLS button.

3. Press the ▲ or ▼ button to select Slide Show, then press the ENTER

E

button.

N All files in the photo list will be used for the Slide Show.

O

During the slide show, files are displayed in order from the currently shown file.

The Slide Show progresses in the order sorted in the Photo list.

Music files can be automatically played during the Slide Show if the Background

Music is set to On.

While a photo list is displayed, press the remote control to start slide show.

(Play)/ ENTER E button on the

USB r Normal SNv11114.JPG

3648x2432 2008/3/15 1/4

E Pause lr Previous/Next

T

Tools R Return

N SlideShow Control Buttons

ENTER

E

Play/Pauses the Slide Show.

Play the Slide Show.

Pause the Slide Show.

Exit Slide Show and return to the photo list.

T TOOLS Run various functions from the Photo menus.

/ Change the SlideShow playing speed.

❑

Playing the selected photo files

1. Press the ◄ or ► button to select the desired photo in the Photo list.

2 . Press the yellow button. Repeat the above operation to select multiple photos.

N

N

The c mark appears to the left of the selected photo.

To deselect all selected files, press the TOOLS button and select Deselect All.

3. Press the

N

(Play) / ENTER E button.

The selected files will be used for the Slide Show.

❑

„

„

„

„

„

Slide Show Tools Menu

Stop Slide Show / Start Slide Show

You can start or stop a SlideShow.

Tools

Slide Show Speed → Normal / Slow / Fast

You can select the slide show speed only during the slide show.

N

You can also change the speed of the Slide Show by pressing the

(FF) button during the Slide Show.

Rotate → 0˚/ 90˚ / 180˚ / 270˚

You can rotate photos saved on a USB memory device.

N

The rotated file is not saved.

(REW) or

Stop Slide Show

Slide Show Speed

Rotate

Zoom

Background Music

Picture Setting

Sound Setting

Information

Remove Safely

: Normal

U Move E Enter e Exit

Zoom → x1 / x2 / x4

You can magnify photos saved on a USB memory device.

N

N

To move the enlarged photo image, press the ENTER E button, then press the ▲/▼/◄/► buttons. Note that when the enlarged picture is smaller than the original screen size, the location change function doesn’t work.

The enlarged file is not saved.

N

N

•

•

Background Music

You can set and select background music when watching a Slide Show.

To use this feature, there must be music on the USB device.

Loading music files is needed to change BGM mode. Play music files in music category to load.

Background Music → On / Off

Select Music File

N If you set Background Music to On, you can select a music file.

„

„

„

Picture Setting / Sound Setting

Refer to page 33.

Information

The photo file information is displayed.

Remove Safely

You can remove the device safely from the TV.

English - 30

BN68-02064A_Eng.indd 30 2009-09-18 �� 9:41:12

Using and Sorting the Music List

You can sort music files in the Music List by a particular standard.

1. Press the MEDIA.P button on the remote control to display the Media Play menu.

2. Press the ◄ or ► button to select Music, then press the ENTER

E

button.

3. Press the ENTER

E

button to start playing music in the order selected by the user.

N

N

The information of the music files is automatically set.

If there is no title information for a music file, the filename is displayed.

NPKI usermanual

USB

USB „ Device

▶

1

1

Energetic 3/4

Carol kidd

Mr A-Z

2005

Pop

When I Dream

▶

Heaven

Select

T

Tools R Return

❑

„

„

„

Music List Tools Menu

Play Current Group

You can only play music files in the currently selected sorting group.

Information

The music file information including the name, the size, the date modified and the path is displayed.

O

Alternatively, select a music file from the music list and press the INFO button to view the information.

Remove Safely

You can remove the device safely from the TV.

NPKI

NPKI usermanual

USB

USB „ Device

1

1

Energetic 3/4

Carol kidd

Mr A-Z

2005

Pop

When I Dream

Play Current Group

Information

Remove Safely

Heaven

Sky

Select

Select

T Tools R Upper Folder

T

Tools R Return

BN68-02064A_Eng.indd 31

English - 31

2009-09-18 �� 9:41:12

Playing a Music

❑

Playing a music file

1. Pressing the ◄ or ► button to select a music file to be played.

2. Press the (Play)/ ENTER E button.

N This menu only shows files with the MP3 file extension. Files with other

N

N file extensions are not displayed, even if they are saved on the same USB device.

(REW) or (FF) buttons do not function during play.

The selected file is displayed at the top with its playing time.

N

N

To adjust the music volume, press the volume button on the remote control.

To mute the sound, press the M MUTE button on the remote control.

The playing duration of a music file may be displayed as ‘00:00:00’ if its playing time information is not found at the start of the file.

N Music Play Control Buttons

ENTER E

Play/Pauses the music file.

Play the music file

Pause the music file r

Geek In The Pink

00:00:02 / 00:04:55 r

When I Dream

USB r Heaven

1/2

E Pause lr Previous/Next

T

Tools R Return

Exit play mode and return to the music list.

T TOOLS Run various functions from the Music menus.

N Music function information icon

When all music files in the folder (or the selected file) are repeated. Repeat Mode is On.

When all music files in the folder (or the selected file) are played once. Repeat Mode is Off.

❑

Playing the selected music files

1. Press the ◄ or ► button to select the desired music file in the music list.

2. Press the yellow button. Repeat the above operation to select multiple music files.

N

N

The c mark appears to the left of the selected music file.

To deselect all selected files, press the TOOLS button and select Deselect All.

3. Press the (Play)/ ENTER E button.

N

Only the selected file is played.

❑

„

Music Play Tools Menu

Repeat Mode → On/Off

You can play music files repeatedly.

„

Picture Setting / Sound Setting

Refer to page 33.

„

Information

The music file information is displayed.

„

Remove Safely

You can remove the device safely from the TV.

Repeat Mode

Picture Setting

Sound Setting

Information

Remove Safely

Tools

◄ On ►

U Move L Adjust e Exit

English - 32

BN68-02064A_Eng.indd 32 2009-09-18 �� 9:41:13

Picture / Music Settings Using Media Play

When watching a SlideShow or listening to music using Media Play, you can set the picture and sound.

❑

Picture Setting

1. Press the TOOLS button during a Slide Show or while music is playing.

2. Press the ▲ or ▼ button to select Picture Setting.

3. Press the ◄ or ► button to select the Picture Mode

( Dynamic, Standard, Eco, or Movie).

4. Press the ▲ or ▼ button to move to an item.

( Contrast, Brightness, Color, Dynamic Contrast, Black Tone, or Reset)

N

Select Reset to initialize the picture settings.

5. Press the ◄ or ► button to adjust the settings.

❑

Sound Setting

1. Press the TOOLS button during a Slide Show or while music is playing.

2. Press the ▲ or ▼ button to select Sound Setting.

3. Press the ◄ or ► button to select the Sound Mode.

( Standard, Music, Movie, Clear voice, or Custom)

4. Press the ▲ or ▼ button to move to an item.

( Balance, 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment), or Reset)

N

Select Reset to initialize the sound settings.

5. Press the ◄ or ► button to adjust the settings.

Picture Mode

Contrast

Brightness

Color

Dynamic Contrast

Black Tone

Reset

Picture Setting

:

:

:

:

◄

:

Standard

95

45

50

Medium

Off

►

U Move L Adjust E Enter R Return

Sound Setting

Sound Mode

Balance

100Hz

300Hz

1KHz

3KHz

10KHz

Reset

◄

:

:

:

:

:

:

Custom

L50 R50

0

0

0

0

0

►

U Move L Adjust E Enter R Return

Using the Setup Menu

Setup displays the user settings of the Media Play menu.

1. Press the MEDIA.P button on the remote control to display the Media Play menu.

2. Press the ◄ or ► button to select Setup, then press the ENTER E button.

3. Press the ▲ or ▼ button to select the desired option.

4 . Press the ◄ or ► button to select the option, then press the ENTER E button.

N

To exit Media Play mode, press the MEDIA.P button on the remote control.

„

„

„

„

Music Repeat Mode → On / Off

Select to repeatedly play music files.

Screen Saver Run Time → 10 min / 20 min / 40 min / 1 hour

Select to set the waiting time before the screen saver appears.

Information

Select to viewing the information of the connected device.

Remove Safely

You can remove the device safely from the TV.

Media Play

USB : USB name

851.98MB/995.00MB Free

SETUP

Photo

USB „ Device

Music Setup e

Exit

Music Repeat Mode

Screen Saver Run Time

Information

Remove Safely

◄

:

Off

10 min

►

USB „ Device U Move lr Adjust R Return

English - 33

BN68-02064A_Eng.indd 33 2009-09-18 �� 9:41:14

About Anynet+

Connecting Anynet+ Devices

Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung TV’s remote.

The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.

❑

To connect to a TV

TV

Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3 Anynet+ Device 4

HDMI 1.3 Cable

HDMI 1.3 Cable

HDMI 1.3 Cable

HDMI 1.3 Cable

1. Connect the [HDMI IN 1], [HDMI IN 2 (DVI)], [HDMI IN 3], or [HDMI IN 4] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

❑

To connect to Home Theater

TV

Home Theatre

Anynet+ Device 1

Optical Cable

HDMI 1.3 Cable

Anynet+ Device 2 Anynet+ Device 3

HDMI 1.3 Cable

Anynet+ Device 4

HDMI 1.3 Cable

HDMI 1.3 Cable

HDMI 1.3 Cable

N

N

N

N

1. Connect the [HDMI IN 1], [HDMI IN 2 (DVI)], [HDMI IN 3], or [HDMI IN 4] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

N

N

Connect the Optical cable between the DIGITAL AUDIO OUT (OPTICAL) jack on your TV and the Digital Audio Input on the Home

Theater.

When following the connection above, the Optical jack only outputs 2 channel audio. You will only hear sound from the Home

Theater’s Front Left and Right speakers and the subwoofer. If you want to hear 5.1 channel audio, connect the Digital Audio Out

(Optical) jack on the DVD player or Cable/Satellite Box (ie Anynet Device 1 or 2) directly to the Amplifi er or Home Theater, not the

TV.

Connect only one Home Theater.

You can connect an Anynet

Anynet

+ device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions.

+ works when the AV device supporting Anynet+ is in the Standby or On status.

Anynet + supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.

English - 34

BN68-02064A_Eng.indd 34 2009-09-18 �� 9:41:16

Setting Up Anynet+

The following settings help set the Anynet+ functions.

T

Press the TOOLS button to display Tools menu.

You can also display Anynet+ menu by selecting Tools → Anynet+(HDMI-CEC).

❑

Setup

„

Anynet+(HDMI-CEC) → Off / On

To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On.

N

When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.

„

Auto Turn Off → No / Yes

Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off

N

The active source on the TV remote must be set to TV to use the Anynet + function.

N

If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned off. If an external device is still recording, it may or may not turn off.

Device List

Setup

Media Play (USB)

Anynet+ (HDMI-CEC)

U Move E Enter R Return

►

Anynet+(HDMI-CEC)

Auto Turn Off

: On

: Yes

▶

U Move E Enter R Return

Scanning and Switching between Anynet+ Devices

N

N

N

N

1. Press the TOOLS button. Press the ENTERE button to select

Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Device List, then press the ENTERE button.

N

N

Anynet+ devices connected to the TV are listed. If you cannot find a device you want, press the red button to scan for devices.

Only when you set Anynet+ (HDMI-CEC) to On in the Setup menu, the Device List menu appears.

3. Press the ▲ or ▼ button to select to a particular device and press the ENTERE button. It is switched to the selected device.

N

View TV

Device List

Record

DVDR MENU

DVDR INFO

Receiver

Setup

:

:

DVDR

On

U Move E Enter R Return

Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation.

The time required to scan for devices is determined by the number of connected devices.

When the device scan is complete, the number of devices found are not displayed.

Although the TV automatically searches the device list when the TV is turned on via the power button, devices connected to the TV when the TV is on or under some conditions are not automatically displayed in the device list. Press the red button to search for the connected device.

If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function. Make sure to switch to an Anynet+ device by using the Device List.

Continued...

English - 35

BN68-02064A_Eng.indd 35 2009-09-18 �� 9:41:17

❑

Anynet + Menu

The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.

Anynet+ Menu

View TV

Device List

(device_name) MENU

Description

Anynet+ mode changes to TV broadcast mode.

Shows the Anynet+ device list.

Shows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of the

DVD recorder will appear.

(device_name) INFO

Record: (*recorder)

Shows the play menu of the connected device. E.g. If a DVD recorder is connected, the play menu of the DVD recorder will appear.

Starts recording immediately using the recorder. (This is only available for devices that support the recording function.)

(*recorder) Reserve Recording Enables reserving a recording for the recorder. (This is only available for devices that support the recording reservation function.)

Stop Recording: (*recorder)

Receiver

Stops recording.

Sound is played through the receiver.

N

If more than one recording device is connected, they are displayed as (*recorder) and if only one recording device is connected, it will be represented as (*device_name).

❑

TV Remote Control Buttons Available in Anynet+ Mode

Device Type

Anynet+ Device

Device with built-in Tuner

Operating Status

After switching to the device, when the menu of the corresponding device is displayed on the screen.

After switching to the device, while playing a file

After switching to the device, when you are watching a TV programme

Available Buttons

Numeric buttons

▲/▼/◄/►/ ENTERE buttons

Colour buttons / EXIT button

(Backward search) / (Forward search) (Stop) / (Play) /

(Pause)

P / button

Audio Device When Receiver is activated

=

/ button

M MUTE button

N

N

N

N

N

N

The Anynet+ function only works when the active source on the TV remote control is set to TV.

The button works only while in the recordable state.

You cannot control Anynet+ devices using the buttons on the TV. You can control Anynet+ devices only using the TV remote control.

The TV remote control may not work under certain conditions. In this case, reselect the Anynet+ device.

The Anynet+ functions do not operate with other manufacturers’ products.

The , operations may differ depending on the device.

Recording

You can make a recording of a TV programme using a Samsung recorder.

1. Press the TOOLS button. Press the ENTERE button to select

Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Record: (device_name), then press the ENTERE

N

N

N button. Recording begins.

View TV

Device List

Record

DVDR MENU

: DVDR

N

N

When there is more than one recording device

When multiple recording devices are connected, the recording devices are listed.

Press the ▲ or ▼ button to select a recording device and press the ENTERE button. Recording begins.

When the recording device is not displayed

Select Device List and press the red button to search devices.

DVDR INFO

Receiver

Setup

: On

U Move E Enter R Return

You can record the source streams by selecting Record: (device_name).

Pressing the button will record whatever you are currently watching. If you are watching video from another device, the video from the device is recorded.

Before recording, check whether the antenna jack is properly connected to the recording device. To properly connect an antenna to a recording device, refer to the recording device’s users manual.

English - 36

BN68-02064A_Eng.indd 36 2009-09-18 �� 9:41:17

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.

1. Press the TOOLS button. Press the ENTERE button to select Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select On or Off.

N

N

N

N

N

View TV

Device List

If your receiver supports audio only, it may not appear in the device list.

The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.

When the receiver (home theater) is set to On, you can hear sound output from the

Record

DVDR MENU

DVDR INFO

Receiver

Setup

:

◄

DVDR

On ►

TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component

U Move E Enter R Return such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.

When listening through the receiver, there are restrictions for using the audio-related menus.

If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power failure), the Speaker Select may be set to External Speaker when you turn the TV on again. (see page 21)

Troubleshooting for Anynet+

Symptom

Anynet+ does not work.

I want to start Anynet+.

I want to exit Anynet+.

The message Connecting to

Anynet+ device... appears on the screen.

The Anynet+ device does not play.

The connected device is not displayed.

The TV programme cannot be recorded.

The TV sound is not output through the receiver.

Solution

•

•

•

•

•

•

•

•

•

• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet + devices only.

Connect only one receiver (home theater).

Check if the Anynet

Check the Anynet

+ device power cord is properly connected.

+ device’s Video/Audio/HDMI 1.3 cable connections.

Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

Check whether the TV remote control is in TV mode.

Check whether it is Anynet + exclusive remote control.

Anynet+ doesn’t work in certain situations. (Searching channels, Operating WISELINK Pro,

Plug & Play, etc.)

When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or turn your TV off and on again.

Check if the Anynet + Function of Anynet+ device is set on.

•

•

•

•

•

•

•

•

Check if the Anynet+ device is properly connected to the TV and check if the Anynet+

(HDMI-CEC) is set to On in the Anynet+ Setup menu.

Press the

Select View TV in the Anynet

Press the

TV button on the TV remote control to switch to TV. Then press the TOOLS button to show the Anynet+ menu and select a menu you want.

+ menu.

SOURCE button on the TV remote control and select a device other than Anynet+ devices.

(Note that the channel button operates only when a tuner-embedded Anynet connected.)

+ device is not

You cannot use the remote control when you are configuring Anynet + or switching to a view mode.

Use the remote control when the Anynet + setting or switching to view mode is complete.

You cannot use the play function when Plug & Play is in progress.

•

•

•

•

•

•

• Check whether or not the device supports Anynet + functions.

Check whether or not the HDMI 1.3 cable is properly connected.

Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

Search Anynet + devices again.

You can connect an Anynet + device using the HDMI 1.3 cable only. Some HDMI cables may not support Anynet+ functions.

If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power failure, please repeat the device scan.

Check whether the antenna jack on the recording device is properly connected.

• Connect the optical cable between TV and the receiver.

English - 37

BN68-02064A_Eng.indd 37 2009-09-18 �� 9:41:17

Recommendations for Use

Teletext Feature

Most television stations provide written information services via Teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.

N

For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.

1 : (exit)

Exit from the teletext display.

2 6 (index)

Used to display the index (contents) page at any time while you are viewing teletext.

3 8 (store)

Used to store the teletext pages.

4 4 (size)

Press to display the double-size letters in the upper half of the screen. For lower half of the screen, press it again. To display normal screen, press it once again.

1

5 5 (reveal)

Used to display the hidden text (answers to quiz games, for example). To display normal screen, press it again.

6 / (teletext on/mix)

Press to activate teletext mode after selecting the channel providing the teletext service.

Press it twice to overlap the teletext with the current broadcasting screen.

2

3

7

8

9

0

7 1 (sub-page)

Used to display the available sub-page.

8 2 (page up)

Used to display the next teletext page.

9 3 (page down)

Used to display the previous teletext page.

0 0 (mode)

Press to select the teletext mode (LIST/FLOF). If you press it in the LIST mode, it switches into the List save mode. In the List save mode, you can save teletext page into list using the 8(store) button.

!

9 (hold)

Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically. To resume, press it again.

4

5

6

!

@

#

@ 7 (cancel)

Used to display the broadcast when searching for a page.

# Colour buttons (red/green/yellow/blue)

If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext page are colour-coded and can be selected by pressing the coloured buttons. Press one of them corresponding to the required. The page is displayed with other coloured information that can be selected in the same way. To display the previous or next page, press the corresponding coloured button.

N

You can change teletext pages by pressing the numeric buttons on the remote control.

Continued...

English - 38

BN68-02064A_Eng.indd 38 2009-09-18 �� 9:41:18

The teletext pages are organized according to six categories:

Part Contents

A Selected page number.

B Broadcasting channel identity.

C Current page number or search indications.

D Date and time.

E Text.

F Status information.

FASTEXT information.

N

-

-

-

Teletext information is often divided between several pages displayed in sequence, which can be accessed by:

Entering the page number

Selecting a title in a list

Selecting a coloured heading (FASTEXT system)

O

Press the TV button to exit from the teletext display.

Wall Mount Kit Specifications (VESA)

Install your wall mount on a solid wall perpendicular to the floor.

When attaching to other building materials, please contact your nearest dealer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

Product Family

LCD-TV inch

19" ~22"

23"~29"

30"~40"

46"~55"

57"~70"

80" ~

VESA Spec. (A * B) Standard Screw Quantity

100 * 100

M4

200 * 100

200 * 200

400 * 400

800 * 400

1400 * 800

M6

M8

4

42"~ 50"

58"~ 63"

400 * 400

600 * 400

PDP-TV

800 * 400

1400 * 800

M8 4

70" ~

80" ~

N

N

N

N

N

N

N

N

We provided the standard dimensions for wall mount kits as shown in the table above.

When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.

Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.

For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.

Do not use screws that do not comply with the VESA standard screw specifications.

Do not use fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury.

Samsung is not liable for these kinds of accidents.

Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.

Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit for this model.

Do not exceed 15 degrees tilt when mounting this TV.

Do not install your Wall Mount Kit while your TV is turned on.

It may result in personal injury due to electric shock.

English - 39

BN68-02064A_Eng.indd 39 2009-09-18 �� 9:41:18

Preparing before installing Wall- Mount on the wall

Case A. Installing SAMSUNG Wall-Mount Case B. Installing other company’s Wall-Mount

1. Install Wall Mount with the torque range of 15kgf·cm or less. Make sure that parts can be damaged if the torque is out of the specified range.

2. Accessory Kit contains Holder–Ring [②] for installing other company’s Wall-Mount on Samsung TV. (Case B)

N

Screw down the hole [ ① ] when installing wall-mount on the wall.

How to assemble the Stand-Base

(depending on the model)

Using the screws for securing the stand base and the monitor, firmly attach the monitor to the stand base.

(The exterior of the set may be different than the picture.)

In case of installing your TV on the wall, close the cover (1) on the stand-base connection part using two screws for hiding.

Warning

(PS50B550) (PS58B550)

Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury.

N

Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen.

Always store the TV upright.

English - 40

BN68-02064A_Eng.indd 40 2009-09-18 �� 9:41:21

경고

경고

주의

Securing the TV to the Wall

Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang

주의 safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.

Wall

Wall

To avoid the TV from falling

1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed onto the wall.

N

N

You may need additional material such as an anchor depending on the type of wall.

Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.

2. Remove the screws from the center back of the TV, put the screws into the clamps, and then fasten the screws onto the TV again.

N

Screws may not be supplied with the product.

3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string tightly.

N

N

N

Install the TV near to the wall so that it does not fall backwards .

It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV.

Untie the string before moving the TV.

4. Verify all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you have any doubt about the security of your connections,contact a professional installer.

10 cm

Securing the Installation Space

Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.

Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product.

Install the product so the required distances shown in the figure are kept.

N

N

When using a stand or wall-mount, use parts provided by Samsung Electronics only.

If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the product

falling.

If you use parts provided by another manufacturer, it may result in a problem with the product or fire due to an increase in the internal temperature of the product due to poor ventilation.

The appearance may differ depending on the product.

„

When installing the product with a stand

„

When installing the product with a wall-mount

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

English - 41

BN68-02064A_Eng.indd 41 2009-09-18 �� 9:41:22

Troubleshooting

If the TV seems to have a problem, first try this list of possible problems and solutions.

Problem Possible Solution

Picture Quality

First of all, please perform the Picture Test to confirm that your TV is properly displaying test image.

* Go to MENU → Support → Self Diagnosis → Picture Test

If the test image is properly displayed, the poor picture may caused by the source or signal.

TV image does not look as good as it did in the store.

Picture is distorted: macroblock,small block, dots,pixelization.

Wrong or missing color with

Component connection.

Poor color or brightness.

Dotted line on the edge of screen.

•

•

•

If you have an analog Cable/Set top box, upgrade to an Box.

Use HDMI or Component cables to deliver HD picture quality.

Cable/Satellite subscriber : Try HD (High Definition) stations from channel line up.

Antenna connection: Try HD stations after performing Auto program

N

Many HD channels are upscaled from SD (Standard Definition) contents.

Adjust Cable/Set top video output resolution to 1080i or 720p.

•

•

•

Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies.

Low signal level can cause picture distortion. This is not a TV issue. Have the antenna accessed.

• Make sure the Component cables are connected to the correct jacks.

Incorrect or loose connections may cause color problems or the screen will be blank.

•

•

•

•

•

Adjust Picture options in the TV menu (Picture Mode, Colour, Brightness,

Sharpness).

Adjust Energy Saving option in Setup menu.

Try picture reset to view the default picture setting.

(Go to MENU → Picture → Picture Reset)

If picture size is set to Just scan, change to 16:9.

Change cable/satellite box resolution.

Picture is black and white with AV

(Composite) input only.

Picture freezes or is distorted when changing channels or picture is delayed.

• Confirm Composite (yellow) cable is in yellow jack in source as well as TV.

•

•

If connected with cable /set top box, please try to reset cable box. (reconnect AC cord and wait until cable box reboots. It may take up to 20 minutes)

Set output resolution of cable box to 1080i or 720p

Sound Quality

First of all, please perform the Sound Test to confirm that your TV audio is properly operating.

* Go to MENU → Support → Self Diagnosis → Sound Test

If the audio is OK, the sound problem may caused by the source or signal.

No sound or sound is too low at maximum volume.

Picture is good but no sound.

Noise from speaker.

•

•

•

•

•

•

•

•

•

Please check the volume of device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.

Then, adjust the TV volume accordingly.

Set the Speaker Select option to TV speaker in the sound menu.

Make sure audio cables from an external device are connected to correct audio input jacks on the TV.

Check connected device's audio output option.

Ex) You may need to change your cable box' audio option to HDMI when you have

HDMI connected to your TV.

If you are using a DVI to HDMI cable, a separate audio cable is required.

Remove plug from headphone jack (if available on your TV).

Reboot the connected device by reconnecting the device’s power cable.

Check cable connections. Make sure a video cable is not connected to an audio input.

For Antenna/Cable connection, check signal strength. Low signal level may cause sound distortion.

BN68-02064A_Eng.indd 42

English - 42

Continued...

2009-09-18 �� 9:41:22

Problem

No Picture, No Video

TV won't turn on.

Possible Solution

TV turns off automatically.

No picture/Video.

•

•

•

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

Make sure the wall outlet is working.

Try pressing the Power button on the TV to make sure the remote is working properly.

If the TV turns on, it may be caused by Remote Control.

To fix the Remote problem, refer to "Remote control does not work" below.

•

•

•

• Check if the Sleep Timer is set to On in the Setup menu.

If connected the TV to your PC, check your PC power settings.

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

If there is no signal for about 10 ~ 15 minutes with Antenna/Cable connection, the TV will turn off.

•

•

•

•

•

Check cable connections. (remove and reconnect all cables of TV and external devices)

Set your external device's (Cable/Sat Box, DVD, Blu-ray etc) video output to match the connections to the TV input. For example, external device's output : HDMI , TV's input : HDMI.

Make sure your connected device is powered on.

Make sure to select the TV's correct source by pressing the remote control.

SOURCE button on the

Reboot the connected device by reconnecting the device’s power cable.

RF (Cable/Antenna) Connection

Cannot receive all channels.

Picture is distorted : macroblock,small block,dots,pixelization.

•

•

•

•

• Make sure coaxial cable is connected securely.

Please try Plug & Play to add available channels to the channel list.

Go to MENU → Setup → Plug & Play and wait for all available channels are stored.

Verify Antenna is positioned correctly.

Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies.

Low signal level can cause picture distortion. This is not a TV issue. Have the antenna accessed

PC Connection

“Not Supported Mode” message.

PC is always shown on source list even if not connected.

Video is OK but there is no audio with

HDMI connection.

•

• Set your PC's output resolution so it matches the resolutions supported by the TV.

This is normal; PC is always shown on the source list even though a PC is not connected.

• Check the audio output setting on your PC.

BN68-02064A_Eng.indd 43

English - 43

Continued...

2009-09-18 �� 9:41:23

Problem Possible Solution

Others

Picture is not shown in full screen.

Remote control does not work.

Plasma TV is making humming noise.

Image Retention (Burn In) Issue.

Can not control TV power or volume with Cable/Sat box remote control.

“Not Supported Mode” message.

Plastic smell from TV.

TV Signal Strength is unavailable in the

Self Diagnostic Test menu.

TV is tilted to right or left side.

Can not assemble stand base.

Channel menu is grey out (unavailable).

Your settings are lost after 30 minutes or every time TV is turned off.

Intermittent loss of audio or video.

•

•

•

Black bars on each side will be shown on HD channels when displaying upscaled SD

(4:3) contents.

Black bars on Top & Bottom will be shown on movies that have aspect ratios different from your TV.

Adjust picture size option on your external device or TV to full screen.

•

•

•

•

•

•

•

•

Replace the remote control batteries with correct polarity (+ -).

Clean the transmission window located on the top of the remote.

Try pointing the remote directly at the TV from 5~6 feet away.

Plasma TVs typically make a soft humming sound. This is normal. It’s caused by the electrical charges that are used to create the images on the screen.

If the humming sound is loud, you may have set the brightness on the TV too high.

Try setting the brightness lower.

You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface. Also try rerouting your connection cables.

Improper installation of wall mount can create excessive noise.

To minimize the possibility of screen burn, this unit is equipped with screen burn reduction technology. Pixel Shift technology enables you to set picture movement up/ down (Vertical Line) and side to side (Horizontal Dot).

• Program the Cable/Set top box remote control to operate the TV.

Refer to Cable/Set top box user manual for SAMSUNG TV code.

• Check the supported resolution of the TV and adjust the external device's output resolution accordingly. Refer to resolution settings in this manual.

• This smell is normal and will dissipate over time.

• This function is only available with digital channels with an Antenna (RF/Coax) connection.

• Remove the stand base from TV and reassemble.

• Make sure TV is placed on flat surface.

If can not remove screws from TV, please use magnetized screw driver.

• Channel menu is only available when TV source is selected.

•

•

•

If TV is in the Store Demo mode, it will reset audio and picture settings every

30 minutes.

Please change from Store Demo mode to Home Use mode in the Plug & Play procedure.

Press the SOURCE button to select TV mode, go to MENU → Setup → Plug & Play

→ ENTER

Check cable connections and reconnect.

Can be caused by using overly rigid or thick cables.

Make sure the cables are flexible enough for long term use.

If wall mounting, we recommend using cables with 90 degree connectors.

You may see small particles if you look closely at the edge of the bezel surrounding the TV screen.

• This is part of the product’s design and is not a defect.

N Some of above pictures and functions are available at specific models only.

English - 44

BN68-02064A_Eng.indd 44 2009-09-18 �� 9:41:23

Specifications

The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice.

Model Name

Screen Size (Diagonal)

PC Resolution (Optimum)

Sound (Output)

Dimension (WxHxD)

Body

With stand

Weight

Body

With stand

Environmental Considerations

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

PS50B550

50 inch

1920 x 1080 @ 60 Hz

10 W x 2

1240 x 766 x 74 mm

1240 x 822 x 290 mm

33.4 kg

38.4 kg

N

N

N

This device is a Class B digital apparatus.

Design and specifications are subject to change without prior notice.

For the power supply and Power Consumption, refer to the label attached to the product.

PS58B550

58 inch

1920 x 1080 @ 60 Hz

15 W x 2

1418 x 866 x 74 mm

1418 x 924 x 335 mm

50 °F to 104 °F (10 °C to 40 °C)

10% to 80%, non-condensing

-4 °F to 113 °F (-20 °C to 45 °C)

5% to 95%, non-condensing

38 kg

45 kg

BN68-02064A_Eng.indd 45

English - 45

2009-09-18 �� 9:41:23

Software License

This product uses parts of the software from the Independent JPEG Group. This product uses parts of the software owned by the

Freetype Project (www.freetype.org). This product uses some software pr ograms which are distributed under the GPL/LGPL license. Accordingly, the following GPL and LGPL software source codes that have been used in this product can be provided after asking to [email protected].

GPL software: Linux Kernel, Busybox, Binutils LGPL software: Glibc, ffmpeg, smpeg, libgphoto, libusb, SDL

❑

GNU GENERAL PUBLIC LICENSE

GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Pream ble

The GNU General Public License is a free, copyleft license for software and other kinds of works.

The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things. To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users. Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on generalpurpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free. The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS

0. Definitions.

“This License” refers to version 3 of the GNU General Public License.

“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.

“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “ recipients” may be individuals or organizations.

To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.

A “covered work” means either the unmodified Program or a work based on the Program.

To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.

To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.

An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License.

If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.

1. Source Code.

The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any nonsource form of a work.

A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.

The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the

English - 46

BN68-02064A_Eng.indd 46 2009-09-18 �� 9:41:23

specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.

The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.

The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding

Source.

The Corresponding Source for a work in source code form is that same work.

2. Basic Permissions.

All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law. You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.

Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.

Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section

10 makes it unnecessary.

3. Protecting Users’ Legal Rights From Anti-Circumvention Law.

No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.

4. Conveying Verbatim Copies.

You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any nonpermissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.

You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.

5. Conveying Modified Source Versions.

You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:

a) The work must carry prominent notices stating that you modified it, and giving a relevant date.

b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.

This requirement modifies the requirement in section 4 to “keep intact all notices”.

c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.

d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.

A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.

6. Conveying Non-Source Forms.

You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machinereadable

Corresponding Source under the terms of this License, in one of these ways:

a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the

Corresponding Source fixed on a durable physical medium customarily used for software interchange.

b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding

Source from a network server at no charge.

c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.

English - 47

BN68-02064A_Eng.indd 47 2009-09-18 �� 9:41:23

d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the

Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.

e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and

Corresponding Source of the work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.

A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product. “Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term

(regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM). The requirement to provide Installation

Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network. Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.

7. Additional Terms.

“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this

License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions.

When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission. Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:

a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or

b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal

Notices displayed by works containing it; or

c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or

d) Limiting the use for publicity purposes of names of licensors or authors of the material; or

e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or

f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.

All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.

If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of theadditional terms that apply to those files, or a notice indicating where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.

8. Termination.

You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).

However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular

English - 48

BN68-02064A_Eng.indd 48 2009-09-18 �� 9:41:23

copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to

30 days after your receipt of the notice.

Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.

9. Acceptance Not Required for Having Copies.

You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance.

However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.

10. Automatic Licensing of Downstream Recipients.

Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.

An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.

11. Patents.

A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based.

The work thus licensed is called the contributor’s “contributor version”.

A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version.

For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License.

Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.

If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.

If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.

A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28

March 2007.

Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.

12. No Surrender of Others’ Freedom.

If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the

Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.

13. Use with the GNU Affero General Public License.

Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General

Public License, section 13, concerning interaction through a network will apply to the combination as such.

English - 49

BN68-02064A_Eng.indd 49 2009-09-18 �� 9:41:23

14. Revised Versions of this License.

The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General

Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the

GNU General Public License, you may choose any version ever published by the Free Software Foundation.

If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program.

Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.

15. Disclaimer of Warranty.

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “

AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO

THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU

ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. Limitation of Liability.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR

ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE

USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED

INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH

ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

17. Interpretation of Sections 15 and 16.

If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the

Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively state theexclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

<one line to give the program’s name and a brief idea of what it does.> Copyright (C) <year> <name of author>

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.

org/licenses/>.

Also add information on how to contact you by electronic and paper mail.

If the program does terminal interaction, make it output a short notice like this when it starts in an interactive mode:

<program> Copyright (C) <year> <name of author> This program comes with ABSOLUTELY NO WARRANTY; for details type `show w’.

This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details.

The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public License. Of course, your program’s commands might be different; for a GUI interface, you would use an “about box”.

You should also get your employer (if you work as a programmer) or school, if any, to sign a “copyright disclaimer” for the program, if necessary.

For more information on this, and how to apply and follow the GNU GPL, see <http://www.gnu.org/licenses/>.The GNU General Public

License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public

License instead of this License. But first, please read <http://www.gnu.org/philosophy/why-not-lgpl.html>.

English - 50

BN68-02064A_Eng.indd 50 2009-09-18 �� 9:41:23

❑

GNU Lesser General Public License (LGPL)

GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/>

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The GNU General Public License is a free, copyleft license for software and other kinds of works.

The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.

To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.

For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.

Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable.

Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users. Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free. The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS

0. Definitions.

“This License” refers to version 3 of the GNU General Public License.

“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.

“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “ recipients” may be individuals or organizations.

To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.

A “covered work” means either the unmodified Program or a work based on the Program.

To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.

To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.

An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License.

If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.

1. Source Code.

The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any nonsource form of a work.

A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.

The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it. The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked

English - 51

BN68-02064A_Eng.indd 51 2009-09-18 �� 9:41:24

subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work. The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding Source for a work in source code form is that same work.

2. Basic Permissions.

All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law. You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.

Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.

3. Protecting Users’ Legal Rights From Anti-Circumvention Law.

No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.

4. Conveying Verbatim Copies.

You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any nonpermissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.

5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the

Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:

a) The work must carry prominent notices stating that you modified it, and giving a relevant date.

b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.

This requirement modifies the requirement in section 4 to “keep intact all notices”.

c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.

d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.

A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.

6. Conveying Non-Source Forms.

You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machinereadable Corresponding Source under the terms of this License, in one of these ways:

a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the

Corresponding Source fixed on a durable physical medium customarily used for software interchange.

b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding

Source from a network server at no charge.

c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.

d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the

Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.

English - 52

BN68-02064A_Eng.indd 52 2009-09-18 �� 9:41:24

e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and

Corresponding Source of the work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.

A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product. “Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term

(regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM). The requirement to provide Installation

Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network. Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.

7. Additional Terms.

“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this

License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions.

When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission. Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:

a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or

b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal

Notices displayed by works containing it; or

c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or

d) Limiting the use for publicity purposes of names of licensors or authors of the material; or

e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or

f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.

All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.

8. Termination.

You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.

English - 53

BN68-02064A_Eng.indd 53 2009-09-18 �� 9:41:24

9. Acceptance Not Required for Having Copies.

You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance.

However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.

10. Automatic Licensing of Downstream Recipients.

Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.

An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.

11. Patents.

A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”. A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.

A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28

March 2007.

Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.

12. No Surrender of Others’ Freedom.

If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the

Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.

13. Use with the GNU Affero General Public License.

Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General

Public License, section 13, concerning interaction through a network will apply to the combination as such.

14. Revised Versions of this License.

The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time.

Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General

Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.

English - 54

BN68-02064A_Eng.indd 54 2009-09-18 �� 9:41:24

15. Disclaimer of Warranty.

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “

AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO

THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU

ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. Limitation of Liability.

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR

ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE

USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED

INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH

ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

17. Interpretation of Sections 15 and 16.

If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the

Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.

❑

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively state the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

<one line to give the program’s name and a brief idea of what it does.> Copyright (C) <year> <name of author>

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/ licenses/>.

Also add information on how to contact you by electronic and paper mail.

If the program does terminal interaction, make it output a short notice like this when it starts in an interactive mode:

<program> Copyright (C) <year> <name of author> This program comes with ABSOLUTELY NO WARRANTY; for details type

`show w’. This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details.

The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public License. Of course, your program’s commands might be different; for a GUI interface, you would use an “about box”.

You should also get your employer (if you work as a programmer) or school, if any, to sign a “copyright disclaimer” for the program, if necessary.

For more information on this, and how to apply and follow the GNU GPL, see <http://www.gnu.org/licenses/>.

The GNU General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the

GNU Lesser General Public License instead of this License. But first, please read <http://www.gnu.org/philosophy/why-not-lgpl.html>.

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact [email protected].

OpenSSL License

Copyright (c) 1998-2007 The OpenSSL Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].

5. Products derived from this software may not be called “OpenSSL nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”

English - 55

BN68-02064A_Eng.indd 55 2009-09-18 �� 9:41:24

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim

Hudson ([email protected]).

Original SSLeay License

Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved.

This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson ([email protected])”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

BN68-02064A_Eng.indd 56

English - 56

2009-09-18 �� 9:41:24

This page is intentionally left blank.

BN68-02064A_Eng.indd 57 2009-09-18 �� 9:41:24

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

Country

AUSTRALIA

CHINA

HONG KONG

INDIA

INDONESIA

JAPAN

MALAYSIA

New

U.A.E

zealand

PHILIPPINES

SINGAPORE

SOUTH AFRICA

TAIWAN

THAILAND

Turkey

VIETNAM

Customer Care Centre 

1300 362 603

400-810-5858

010-6475 1880

3698-4698

3030 8282

1800 110011

1800 3000 8282

0800-112-8888

0120-327-527

1800-88-9999

0800 SAMSUNG (0800 726 786)

1-800-10-SAMSUNG(726-7864)

1-800-3-SAMSUNG(726-7864)

1-800-8-SAMSUNG(726-7864)

02-5805777

1800-SAMSUNG(726-7864)

0860-SAMSUNG(726-7864 )

0800-329-999

1800-29-3232

02-689-3232

444 77 11

800-SAMSUNG (726-7864)

8000-4726

1 800 588 889

Web Site www.samsung.com/au www.samsung.com/cn www.samsung.com/hk www.samsung.com/hk_en/ www.samsung.com/in www.samsung.com/id www.samsung.com/jp www.samsung.com/my www.samsung.com/nz www.samsung.com/ph www.samsung.com/sg www.samsung.com/za www.samsung.com/tw www.samsung.com/th www.samsung.com/tr www.samsung.com/ae www.samsung.com/vn

BN68-02064A_Eng.indd 58

BN68-02064A-01

2009-09-18 �� 9:41:24