Samsung | AZ09F1KE | User manual | Samsung AZ09F1KE User Manual

OWNER’S
INSTRUCTIONS
AZ09F1KE
WINDOW-TYPE
ROOM AIR CONDITIONER
(Cool and Heat)
E R DB68-02037A(1)
Safety Precautions
The following safety precautions must be taken when installing
and using your air conditioner.
1 The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
◆ A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2 Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
3 NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
4 Do NOT insert anything between the air outlet blades, as the inner fan may be damaged
and you may be hurt. Particularly, keep children away from the unit.
5 ALWAYS ensure that the power cable is in good condition.
Make sure that it is not walked on or damaged by items placed on or against it.
If the power cord is damaged in any way, it must be replaced by an approved
power cord available from the manufacturer or its service agent.
6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
◆ An approved service center
◆ The outlet at which the air conditioner was purchased
7 Do NOT place any obstacles in front of the unit.
8 The appliance is not intended for use by young children or infirm person without
supervision; young children should be supervised to ensure that they do not play with
the appliance.
CAUTION
The manufacturer do not take the responsibility of the accident happened
because the air conditioner is not fixed firmly or installed securely, during
installing or using the product. In case you have difficulty in installation,
you must ask for an installation specialist help. The accident will be happened in case of installing improperly.
E-2
Contents
◆ PREPARING YOUR AIR CONDITIONER
■
■
■
Safety Precautions .........................................................................................
Air Conditioning Unit - Main Parts and Control Panel ....................................
Getting Started ...............................................................................................
2
4
5
◆ OPERATING YOUR AIR CONDITIONER
■
■
■
■
■
■
Cooling Your Room .........................................................................................
Heating Your Room .........................................................................................
Airing Your Room ............................................................................................
Switching the Air Conditioner Off ...................................................................
Adjusting the Air Flow Direction Horizontally .................................................
Adjusting the Air Flow Direction Vertically ......................................................
6
7
8
8
9
9
◆ RECOMMENDATIONS FOR USE
■
■
■
■
■
Operating Recommendations .........................................................................
Temperature and Humidity Ranges ................................................................
Cleaning Your Air Conditioner .........................................................................
Solving Common Problems ............................................................................
Technical Specifications .................................................................................
10
10
11
12
13
◆ METHOD OF INSTALLATION ................................................................................. 14
E-3
Air Conditioning Unit - Main Parts and Control Panel
❄ The design and shape are subject to
change according to the model.
Inner air flow blades
(right/left orientation)
Air Outlet
Outer air flow blades
(up/down orientation)
Air inlet (Outside)
Air inlet (Inside)
Ventilation lever
Air filter
(The air filter is located in inside )
Power plug
(The type of power plug may
differ, depending on the local
power supply.)
Temperature
control dial
Operating mode
selection dial
Air flow blade swing switch
E-4
Getting Started
You have just purchased a window-type room air conditioner and it has been installed
by your installation specialist.
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s features.
The booklet is organised as follows.
◆ The illustration on page 4 shows the air conditioning unit;
it indicates the location and purpose of the main parts and controls on the unit.
◆ In the main part of the document, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH
☛
➢
IMPORTANT
NOTE
E-5
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the fan speed.
1
Select the operating mode and fan speed.
To cool your room with a...
Set the operating mode
selection dial to...
High fan speed
HI COOL
Low fan speed
LOW COOL
Result:
◆ The air conditioner starts up in Cool mode.
◆ The fan starts up at the speed selected.
➢
2
27˚C ~ 23˚C
You can change modes at any time.
To adjust the temperature, turn the temperature control dial towards
the right and the blue position.
Possible temperatures: Between 18°C and 25°C inclusive.
29˚C
~ 27˚C
Result:
23˚C
~ 18˚C
3
E-6
The air conditioner starts cooling if the room temperature
is higher than the selected temperature.
To control the direction of the air flow, refer to page 9.
Heating Your Room
You must select the Heat mode if you wish to heat your room
to a specific temperature. You can also select the fan speed.
1
Select the operating mode and fan speed.
To heat your room with a...
Set the operating mode
selection dial to...
High fan speed
HI HEAT
Low fan speed
LOW HEAT
Result:
◆ The air conditioner starts up in Heat mode.
◆ The fan starts up at the speed selected.
➢
2
You can change modes at any time.
To adjust the temperature, turn the temperature control dial towards
the left and the red position.
27˚C ~ 23˚C
Possible temperatures: Between 25°C and 29°C inclusive.
Result: The air conditioner starts heating if the room temperature
is lower than the selected temperature.
3
29˚C
~ 27˚C
23˚C
~ 18˚C
To control the direction of the air flow, refer to page 9.
E-7
Airing Your Room
If the atmosphere in your room is stale, you can air it using
the Fan feature and if necessary, evacuate the stale air outside.
1 If you wish to evacuate stale air outside, pull the ventilation lever on the front
of the unit and the open position (
Result:
).
The air inside the room circulates and stale air is evacuated outside.
Otherwise, push the ventilation lever and the closed position (
Result:
Open
Position
).
The air simply circulates inside the room.
Closed
Position
2
Set the operating mode selection dial to the FAN position.
➢
Both fan settings (left and right) have the same function.
Result:
3
The air conditioner starts up in Fan mode.
To control the direction of the air flow, refer to page 9.
Switching the Air Conditioner Off
You can switch the air conditioner off whenever you want.
To switch the unit off, simply set the operating mode selection dial
to the OFF position.
Result:
E-8
The air conditioner stops operating.
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the
unit, thus increasing the efficiency of the air conditioner.
1
Set the air flow blade swing switch to the
Result:
➢
2
position .
The inner blades swing automatically left and right.
The blades may stop swinging momentarily when the Deice function
is activated (see page 10 for further details on this function).
They will start swinging again automatically as soon as the Deice
function stops.
To stop the blades moving left and right, set the air flow blade swing switch
to the
position.
➢
To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply set the switch to the
position
when the blades are in the required position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Heating
Upwards.
Downwards.
Adjust the air flow blades to the required position, by pushing them
upwards or downwards.
➢
If you orient the air flow blades downwards and the unit operates
in Cool mode for a long period of time, dew may:
◆ Form on the surface of the blades
◆ Drip from the blades
E-9
Operating Recommendations
Here are a few recommendations that you should follow when using
your air conditioner.
Topic
Recommendation
Heating
The heat pump inside the air conditioner absorbs heat from
performances outside air and brings it indoors. If the temperature of the outside
air drops, the air conditioner will heat less. If you find that the room
is not warm enough, use an additional heating appliance.
Warm air
circulation
The air conditioner circulates warm air to heat your room;
as a result, some time will be required after starting
the air conditioner to warm the entire room. If necessary,
set the air conditioner going a short time before you wish
to use the room.
Frost
When outside temperatures are low and humidity is high,
frost may form in the unit’s condenser when heating with your
air conditioner.
If this happens:
◆ The unit stops heating
◆ The air flow blades stop swinging
◆ The Deice mode is triggered automatically for about
five minutes.
No intervention is required from you; after about five minutes,
the air conditioner starts operating again normally.
High indoor
and outdoor
temperatures
If both the indoor and outdoor temperatures are high and you
select the Heat mode, the fan and compressor in the unit may
stop at times. This is normal; simply wait until the air conditioner
switches on again.
Power failure
If a power failure occurs when the air conditioner is operating,
the unit is switched off. When the power returns,
the air conditioner starts up again automatically.
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges,
within which the air conditioner can be used.
E-10
Mode
Indoor
Temperatures
Outdoor
Temperature
Indoor Humidity
Heating
28°C or less
0°C to 21°C approx.
-
Cooling
21°C to 32°C approx.
21°C to 43°C approx.
80% or less
If the air conditioner is used at...
Higher temperature
Then...
The automatic protection feature may be triggered
and the air conditioner stopped.
Lower temperature
A water leakage or some other malfunction may happen
if the heat exchanger freezes.
Higher humidity levels
Water may condense on and drip from the surface of the unit
if it is used for long periods.
Cleaning Your Air Conditioner
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
IMPORTANT When cleaning the air conditioner, turn it off and pull out
the power plug.
1
Hold the air filter handle, slightly pull it to the left side and open the front grille.
➢
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.
CAUTION
Removal and Reassembly of the Front Grille
For user's safety, a safety clip has been installed in the front grille.
1 Grasp the lower part of the
front grille and the air filter
handle, then open the grille.
Safety clip
2 Remove the safety clip and
the front grille.
3 When reassembling the front
grille, you should install the
safety clip again.
2
Pull the air filter to the right side.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
➢
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to dry
the inside of the air conditioner
thoroughly.
The air conditioner has two or three
grille grooves depending on the model.
E-11
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
PROBLEM
EXPLANATION / SOLUTION
The air conditioner does not
operate at all
◆ Check that the circuit breaker used for the air conditioner
has not been triggered.
◆ Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
◆ Check that the correct operating mode has been selected
(cooling, heating or airing).
The air conditioner does not
cool or heat
◆ Check that the correct operating mode has been selected, COOL or HEAT.
◆ The room temperature may be too low or too high.
◆ Dust may be blocking the air filter;
refer to page 11 for cleaning instructions.
◆ Check that there is no obstacle blocking the air flow into or out of the unit.
E-12
When heating, the required room
temperature is never reached
and the air conditioner
frequently stops
◆ Check that the required temperature has been set correctly.
The air flow direction does not
change when you set the air flow
blade swing switch to the
position
◆ Check that the air conditioner has been switched on;
Odours are permeated in the
room during air conditioning
◆ Air the room.
◆ Increase the fan speed.
◆ If the air flow is directed downwards, direct it upwards.
if necessary, turn the operating mode selection dial.
Technical Specifications
Design and specifications are subject to change without
notice.
Model
Power Supply
AZ09F1KE
220-240V~, 50Hz
E-13
Method of Installation
Before installation, be sure to check the installation area
for the air conditioner, and installation method of the drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
85mm
min.
300mm
200mm
500mm
500mm
500mm
Fence, wall
or other
obstacle
Approx.3˚
750mm
150mm min.
➢
◆ If the wall is greater than 150mm thick,
cut the wall back on a 45˚ angle if possible.
45˚
100mm or more
E-14
45˚
Installation of the Drain Tube
Rear
Fix the drain tube as shown in the figure.
Rubber cap
Gasket
Drain Tube
Screws(2EA)
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
◆ In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1
Open the front grille ; refer to page 11.
2
Remove the screw located at the lower section of the front grille.
It is secured in the
section depending on the model.
3
Remove the front panel.
Screw
Front grille
3-1 Press both sides of the cabinet in the direction of the arrow
as shown in the figure.
3-2 Pull the lower part of the front panel slightly forward.
(below three inches/7cm)
3-3 Lift the front panel upward.
☛
Applying excessive force to remove the front panel
may cause damage to the tab ; be sure not to use
excessive force.
4
Remove two screws on the lower, right and left sides of the unit.
5
Remove the chassis from the cabinet.
6
Remove the rubber cap inserted into the basepan.
7
Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
8
Install the cabinet at the specified area after installing the drain pan,
and then re-assemble it in the original condition.
➢
Secure the front panel to the case by replacing the screw removed in
step 2. If a screw not removed in step 2, secure the panel with a
supplied screw.
◆ In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1
Follow steps 6 and 7 only
Front panel
Screw
Rear
Rubber cap
Drain Pan
Drain Hose
Bottom-Side View with
Drain Pan and Hose in Place
E-15
THIS AIR CONDITIONER IS MANUFACTURED BY:
ELECTRONICS
Printed in Korea
Download PDF

advertising