Kenwood DDX8036BTM Car Video System Installation manual

MONITOR WITH DVD RECEIVER
DDX SERIES
DDX8036BT
DDX8036BTM
INSTALLATION MANUAL
© B54-4782-00/00 (MW/M2W/XW)
Accessories
1
Installation Procedure
9
..........1
2
..........6
0
..........1
..........1
3
!
..........1
4
..........1
@
..........1
5
..........2
6
..........1
7
..........1
1. To prevent a short circuit, remove the key
from the ignition and disconnect the battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring
harness.
4. Connect the wiring harness wires in the
following order: ground, battery, ignition.
5. Connect the wiring harness connector to
the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
9. Perform the Initial Setup. (Refer to the
Instruction Manual.)
2WARNING
..........1
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
About the Front Panel
When removing the product from the
box or installing it, the front panel may be
positioned at the angle shown in (Fig. 1). This
is due to the characteristics of a mechanism
the product is equipped with.
If the program that is activated when the
product is first powered on works properly,
the front panel will automatically move into
the position (initial setting angle) shown in
(Fig. 2).
8
(Fig. 1)
(Fig. 2)
..........6
2
DDX SERIES
After the Installation
After the installation, perform the Initial Setup
by referring to the instruction manual.
•
¤
•
• Mounting and wiring this product requires
skills and experience. For safety’s sake, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON (“PROTECT” is
displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to a
power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the wires or ground them to any metal part in the car.
• When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not mix front and rear).
For example, if you connect the + connector
of the left speaker to a front output terminal, do
•
•
•
not connect the - connector to a rear output
terminal.
After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
Mount the unit so that the mounting angle is 30°
or less.
This unit has the cooling fan (page 5) to decrease
the internal temperature. Do not mount the unit
in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the
cooling of the internal temperature and result in
malfunction.
Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
Reception may drop if there are metal objects
near the Bluetooth antenna.
Bluetooth antenna unit
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
English
3
Connection
connect the ignition wire (red) and the battery wire (yellow)
¤ Iftoyou
the car chassis (ground), you may cause a short circuit, that in
Ignition key
switch
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
ACC
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
(Main fuse)
Antenna Cord
Car fuse box
A
Ground wire (Black) (To car chassis)
FM/AM antenna input
A
Battery
to the vehicle's parking brake
⁄ Connect
detection switch harness.
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Connect to vehicle's reverse lamp harness when
using the optional rear view camera.
To steering remote
⁄
To use the steering wheel remote control feature, you need to
an exclusive remote adapter (not supplied) matches your car is
required.
To car light control switch
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
⁄
To connect the Kenwood navigation system,
consult your navigation manual.
Depending on what antenna you are using,
connect either to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier,
connect to its power control terminal.
⁄
4
If no connections are made, do not let the cable come out from the tab.
DDX SERIES
Bluetooth Microphone
(Accessory !) (see page 8)
Cooling fan
FUSE (15A )
Reverse sensor wire (Purple/White)
REVERSE
Accessory 1
To front left speaker
White/Black
White
+
Steering remote control input (Light Blue/Yellow)
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
Dimmer control wire (Orange/White)
To front right speaker
Gray/Black
Gray
+
ILLUMI
Mute control wire (Brown)
MUTE
To rear left speaker
Green/Black
+
Green
Motor antenna control wire (Blue)
ANT. CONT
Power control wire (Blue/White)
P.CONT
To rear right speaker
Purple/Black
Purple
+
English
5
System Connection
iPod (commercially available)
USB terminal
iPod
USB device (commercially available)
Audio input (iPod/AV Input 3 switchable)
Resistance-free stereo type mini plug (3.5φ)
Visual input (iPod/AV Input 3 switchable)
Resistance-free mini plug (3.5φ)
Accessory 4
Accessory 2
AV IN1
To Camera
control terminal
AV OUT
Accessory 3
To Relay Box
(Blue/Red)
CENTER
SUB
WOOFER
REAR
RELAY 2
RELAY 1
(Blue/Red)
FRONT
(Green/White)
REAR VIEW
CAMERA
AV IN 2
(Green/Red)
6
Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
Audio/Visual Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Audio/Visual Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Rear View Camera Input
• Visual input (Yellow)
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Center Preout
DDX SERIES
Optional Accessory Connection
iPod
(commercially available)
KCA-iP301V
(Optional Accessory)
Visual Output (Yellow)
USB terminal
USB terminal
iPod
Audio Output (Black)
USB device
(commercially available)
TV Tuner
(Optional Accessory)
Navigation System
(Optional Accessory)
Connection cable
(Included in the
Navigation System)
TO MONITOR UNIT
Connection cable
(Included in the TV tuner)
units that can be connected to this unit.
⁄ Navigation
(As of December, 2009):
• KNA-G630
• KNA-G630CN
For latest information, access the
www.kenwood.com/cs/ce/.
English
7
Installing the Microphone Unit
1. Check the installation position of the
microphone (accessory !).
2. Remove oil and other dirt from the
installation surface.
3. Install the microphone.
4. Wire the microphone cable up to the unit
with it secured at several positions using
tape or the like.
Accessory !
Fix a cable with a commercial item of tape.
Peel the release coated paper of double-face
adhesive tape to fix on the place shown above.
Adjust the direction of the microphone to the driver.
⁄
8
Install the microphone as far as possible
from the cell-phone.
DDX SERIES
Installing the Escutcheon
For General Motors
For Toyota/Scion
1. Cut out accessory 6 to meet the shape of
the opening of the center console.
2. Attach accessory 6 to the unit.
1. Cut out accessory 6 as illustrated.
Cutting line
Cut out to meet the
shape of the opening
in the vehicle.
Accessory 6
Accessory 6
For Volkswagen
1. Attach accessory 0 to the unit.
2. Fold double-sided adhesive (accessory 7)
along the slit and attach it to accessory
6 cut-out against the center rib as
illustrated. Use 2 pieces of accessory 7 for
1 accessory 6 cut-out.
3. Attach accessory 6 cut-out to the unit.
Accessory 7
Accessory 0
English
9
Installation for Monitor/Player Unit
Installation the Monitor/Player
unit
Attaching the monitor panel
Accessory @
Bend the tabs of the mounting sleeve
with a screwdriver or similar utensil and
attach it in place.
⁄
• Make sure that the unit is installed securely in
place. If the unit is unstable, it may malfunction
(eg, the sound may skip).
Installation on Toyota, Nissan or
Mitsubishi Car using Brackets
Hold the monitor panel securely so as not to
drop it accidentally.
Fit the monitor panel onto the attaching
plate until it is firmly locked.
1
1
2
Accessory 8 (M5x6mm)
or Accessory 9 (M5x7mm)
Car Bracket
3
Accessory 8 (M5x6mm)
or Accessory 9 (M5x7mm)
10
DDX SERIES
Removing Monitor/Player Unit
Removing the Hard Rubber
Frame (escutcheon)
1. Engage the catch pins on the removal tool
5 and remove the two locks on the lower
level.
Lower the frame and pull it forward as
shown in the figure.
Removing the Unit
1. Remove the hard rubber frame by referring
to the removal procedure in the section
<Removing the Hard Rubber Frame>.
2. Insert the two removal tools 5 deeply into
the slots on each side, as shown.
Accessory 5
Accessory 5
Catch
Lock
⁄
3. Lower the removal tool toward the
bottom, and pull out the unit halfway
while pressing towards the inside.
• The frame can be removed from the top side in
the same manner.
2. When the lower level is removed, remove
the upper two locations.
⁄
• Be careful to avoid injury from the catch pins on
the removal tool.
4. Pull the unit all the way out with your
hands, being careful not to drop it.
English
11