luxCONTROL lighting control system DALI

luxCONTROL lighting control system DALI
luxCONTROL lighting control
system
DALI sensors
DALI MSensor 5DPI 14
Multi-sensor for DALI system
Product description
• Component of the comfortDIM system (DALI
standalone)
• With ambient light dependent control and motion
detection
• Multiple MSensors possible in a group
• Can be remote controlled
• Lighting control and motion detection can be
deactivated
• Individual adjustment of the parameters with
configuration software
• Multi-master compatible: Multiple control
modules are possible in a DALI system
Fig. 1
• Power supply via DALI line
• 5-year guarantee
È
Standards, page 5
Wiring diagrams and installation examples, page 5
Fig. 2
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
1
luxCONTROL lighting control
system
DALI sensors
16,4
DALI MSensor 5DPI 14
Multi-sensor for DALI system
Technical data
DALI cable
6 mA from DALI
0 ... +50 °C
-25 ... +55 °C
IP20
44,
4
1,
9
3
Ø13,
9
5,5
65,4
Fig.
1
2
12,8
Supply via
Current draw
Operating temperature
Storage temperature
Type of protection
Ø46,
75
Ø58
128
Fig. 2
Ordering data
Type
Article number
DALI MSensor 5DPI 14f Luminaire
installation
DALI MSensor 5DPI 14f black Luminaire
installation
DALI MSensor 5DPI 14rc Ceiling
28000935
28001697
Figur
e1
28000936
Packaging, carton
1
40 pc(s).
40 pc(s).
2
63 pc(s).
installation
Specific technical data
Type
DALI MSensor 5DPI 14f
DALI MSensor 5DPI 14f black
DALI MSensor 5DPI 14rc
Detection
Ø of detection range,
mounted at a height of 2.5
m
4m
Swivel
design
Detection angle
4m
no
no
360°
360°
4m
no
360°
1 The measured value at the sensor head corresponds to approx. 15 to 2,000 lux on the surface measured.
Light
measurement at
the sensor
10 – 650
head1 lx
10 – 650
10 –lx650
Infra-red
control
range
5m
5m
5m
lx
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
2
ACCES
SORIE
S
luxCONTROL lighting control
system
DALI sensors
REMOTECONTROL IR6
Product description
• Optional infra-red remote control
• Switching on and off (On/Off button)
• Dimming (Up/Down button)
• Activation of automatic lighting
control
• Setting the threshold control point
(Set button)
Ordering data
Article number Dimensions L x W x H Packaging carton
28000647
86.5 x 40.5 x 7.2 mm 500 pc(s).
ACCES
SORIE
S
Type
REMOTECONTROL IR6
DALI
RC
Product description
• Optional infra-red remote control
• Switching on and off (On/Off button)
• Dimming (Up/Down button)
• Activating automatic lighting control
(sun/cloud button)
• Calling up two scenes
• Calling up five fixed light output
values (100, 50, 25, 12 and 6
Ordering data
%)
Type
DALI-RC
• Individual adjustment of the button
Article number
86458263
Packaging, carton
10 pc(s).
assignments with configuration
software
• Setting the threshold control point
• With wall bracket
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
3
ACCESS
ORIES
luxCONTROL lighting control
system
DALI sensors
5DPI 14f Mounting Kit
Product description
• Mounting frame for attaching all 5DP 14f sensor
directly to the luminaire housing
• Shutter for preventing movement detection in one
direction
Ordering data
Type
5DPI 14f mounting kit
Article number Packaging carton Weight per pc.
28001558
1 pc(s).
0.004 kg
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
4
luxCONTROL lighting control
system
DALI sensors
The DALI MSensor is the ideal addition to the comfortDIM series of products as it offers daylight-dependent lighting control,
presence detection and remote control.
It has been designed for the following principal applications:
• Individual offices
• Open-plan offices
• Training / presentation rooms
• Corridors, passageways and garages
The DALI MSensor controls a DALI group and is designed that it can be used together with the comfortDIM components (e.g. DALIXC). For this reason the DALI MSensor can be addressed and grouped like an ECG, making system configuration easier. The
configuration of the sensors is done by the masterCONFIGURATOR software tool (since version V2.12). For further information
please refer to the DALI MSensor manual on www.tridonic.com.
As an option, the DALI MSensor can be operated from three remote controls. The remote controls available with the system are:
DALI-RC and REMOTECONTROL IR6.
A maximum of 12 sensors can be operated on one DALI circuit. This restriction is due to
the permitted data traffic on the DALI circuit.
To use the DALI MSensor in conjunction with an external system some modes are available. To ensure a proper function please t ake
account of the advices in the DALI MSensor manual on www.tridonic.com.
Wirin
g
Standards
EN 61547
EN 61347-1
EN 61347-2-11
EN 55015
EN 62386-101/102
L
N
DA
LI
PS
Uconverter
Uconverter
DALI
MSensor
DALI
XC
(GC)
DALI
XC
(SC)
DA
LI
US
B
Multiple sensors can be operated on a DALI
circuit.
The functions of the sensor can be activated
autonomously or in a network of several sensors.
Glow-wire test
according to
EN 61347-1 passed.
DALI standard
The DALI MSensor
is designed to
control con- trol
gear with DALI
stan- dard IEC
60929 (DALI V0)
and IEC 62386
(DALI V1).
Wiring type and cross section for rc version
The wiring can be solid wire or stranded wire with a cross-section of 0.2 mm² to
1.5 mm².
wire
preparation:
0.2 – 1.5
mm²
7.5 – 8.5 mm
Wiring type and cross section for f version
The wiring can be solid wire or stranded wire with a cross-section of 0.2 mm² to
0.5 mm².
wire
preparation:
0.2 – 0.5
mm²
7.5 – 8.5 mm
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
5
luxCONTROL lighting control
system
DALI sensors
Remote control
The DALI MSensor can be controlled with 2 remote controls:
• DALI-RC
• REMOTECONTROL IR6
DALI-RC
IR sender
LED status
display
Light
Switch all luminaires
in the DALI system
ON or OFF
value
100
%
value 25 % brightness
Increase or reduce the
light value (dimming the
DALI system)
Automatic control
Light
mode ON Call up
brightness Light value
50 % brightness Light
value
12
%
brightness Light value
6 % brightness
scene 2
Call up scene 1
Installation
• The DALI MSensor must not be connected to the mains. It is
supplied directly via the DALI signal line.
• A maximum of 12 DALI MSensors must be operated in one DALI circuit.
• DALI is not SELV.
The installation instructions for mains voltage therefore apply.
• Please ensure that the detection range of the sensor lies in the
lighting area of the controlled luminaires.
• Please ensure that the detection ranges of the sensors do not
overlap. This may have influence to the lighting control.
• When installed at a height other than the recommended
installation height (2,5m), the presence sensor might show
different characteristics. W hen mounted at a higher level, its
sensitivity is reduced. If mounted at a lower level, its range is
diminished.
• Heaters, fans, printers and copiers located in the detection
zone may cause incorrect presence detection.
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
6
luxCONTROL lighting control
system
DALI sensors
Light level recognition area
Presence / motion detection
Sensor alignment
Example for light and motion
detection area at height of 1.7 m:
x
2
y
x2
y
x1
yy
1
m
x1
h
α=
78°
y
αx2 =
22°
αx1 =
38°
αy = 30°
0.7
m
h
x2
x1
h
22°
38°
x2
y
y
x1
1.3
m
d
Light level
recognation
area
1m
Presence / motion
detection
y
x2
y
2.8 m
y
x1
x2
yy
x1
h*
x1
x2
y
d
1.7 m 1.3 m 0.7 m 1.0 m 2.8 m
2.0 m 1.6 m 0.8 m 1.2 m 3.2 m
2.3 m 1.8 m 0.9 m 1.3 m 3.7 m
2.5 m 2.0 m 1.0 m 1.4 m 4.0 m
2.7 m 2.1 m 1.1 m 1.6 m 4.4 m
3.0 m 2.3 m 1.2 m 1.7 m 4.9 m
3.5 m 2.7 m 1.4 m 2.0 m 5.7 m
4.0 m 3.1 m 1.6 m 2.3 m 6.5 m
*
The recommended maximum room height for office
applications is 3 m and for corridor applications for
example 4 m.
Up to 2 m mounting height presence is
detected and over 2 m motion is detected.
Calculation of the diameter (light
area): x1 = tan(x1)  h
x2 = tan(x2)  h
y = tan(y)  h
Calculation of the diameter
(motion area): d = 2  tan(0,5 
)  h
The following operating modes can be set for lighting
control via the masterCONFIGURATOR configuration
software:
The following operating modes can be set for the motion
detector via the masterCONFIGURATOR configuration software:
Active
Constant light control is active.
Active
Inactive
Constant light control is deactivated. The lighting is
switched on an adjustable light value.
Off Only
Setpoint adjustment
• REMOTECONTROL IR6: Pressing the Set button (> 3 s)
Never Off
stores the current light value as a new setpoint.
• DALI-RC: Über das Drücken der Automatic-Taste (>3 s) wird
der aktuell gemessene Lichtwert als neuer Sollwert abgespeichert. Inactive
• masterCONFIGURATOR
Bright-out
If the nominal illuminance (e.g. 500 lux) is exceeded for 10
minutes by more than 150 % (e.g. 750 lux), the lighting is
switched off even if motion is detected. The lighting is switched
on again when the measured light value falls below the setpoint.
This function can be adjusted via the masterCONFIGURATOR.
The light is switched on or off automatically
depending on whether or not there is a person in
the
The room.
motion detector only switches the
connected lighting off. The luminaires are
switched on manually via the con- nected
external
switch
or infra-red
control. the sensor
If it has not
detected
any movement
dims to the “Absence value” parameter and
remains
at this
value
The motion
sensor
is deactivated. The light must
be swit- ched on or off manually.
Run-on time
This is the time after which the lighting is switched off if no
movement is detected. It can be set via the “Run-on time”
parameter.
Absence value
On the DALI MSensor you can set whether the light is to be
switched off after the switch-off delay or dimmed to the second
light value. The light value and the dwell time (how long the
value is held) can be set via the “Absence value” and “Switch-off
delay” parameters.
Dead time “Manual-off”
If the system is switched off manually via the switch or remote
control the motion sensor is deactivated. At the end of a delay
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
7
luxCONTROL lighting control
system
DALI sensors
time if motion has not been detected the motion sensor is
activated again. If the sensor detects motion during the
“Manual-off” delay, the time will be reset to the start.
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
8
luxCONTROL lighting control
system
DALI sensors
General settings
Parameter
Motion Detector
Light Regulation
Setpoint Light Regulation
Power On Setting
Bright-out timeout
Bright-out threshold
Control Speed
Switch On Value
Controlled group
Default Values
enabled
enabled
150 lx
no action
10 min
150 %
4
auto (calculated)
Broadcast
Adjustable range
enabled, enabled (only OFF), disabled
enabled, disabled
10 – 650 lx
no action, last state, maximum level, off,
presence
1 – 120 minvalue
100 – 300 %
0 – 7, 0 = slow, 7 = fast
minimum level, maximum level, calculated
Broadcast or group 0 – 15
Default Parameter Motion Detector
Parameter
1 Fade-in time
A Presence value
2 Run-on time
3 Fade time
B Absence value
4 Switch-off delay
5 Fade-off time
Manual-off
Default Values
fast
ambient light-controlled
20 min
5.6 s
3%
10 min
5.6 s
10 min
Adjustable range
fast, 0.7 – 90.5 s
ambient light-controlled, fixed
30 s – 60 min, infinite
fast, 0.7 – 90.5 s
1 – 100 %
0.7 s – 60 min, never OFF
fast, 0.7 – 90.5 s
fast, 0 s – 20 min
ø14, +0,2
0
1
Mounting variants luminair installation sensor:
Size of the sheet: 0.8 –
1.8 mm
Size of the sheet: 0.6 – 0.8 mm
1,5 – 2,5
2,2 0
+0,2
19,
1
2
0
4 +0,2
0
+0,1
-0,1
ø1,
8
3,
2
+0,1
0
0
-0,15
Size of the sheet: 0.8 – 3.0 mm
3,3 – 5,5
+0,2
0
14,10
+0,2
41,
1
R1,
9
0
-0,2
Data sheet 06/16-CO073-12
Subject to change without notice.
www.tridonic.com
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement