Samsung CT-29V10MQ User manual

Document
AA68-03173A_00(E)-FRONT COVER
9/15/03
11:03 AM
Page 1
.............................................................................................................................
CT21S8W/CT21M7W/
CT25M6W/CT25K10MQ/
CT29V10MQ/CT29K10MQ
.............
AA68-03173A-00
COLOR TELEVISION
Owner’s
Instructions
AA68-03173A_00(E)-Inside COVER
9/15/03
11:05 AM
Page 2
Warning! Important
Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is
dangerous to make any kind of contact with any inside part of
this product.
This symbol alerts you that important literature concerning
operation and maintenance has been included with this product.
Note to CATV system installer: This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of
Canadian Electrical Code, Part I), that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practical.
Important: One Federal Court has held that unauthorized recording of
copyrighted TV programs is an infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized
recording in whole or in part may be in violation of these rights.
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
2
AA68-03173A_00(E)-PREFACE
9/15/03
11:27 AM
Page 3
Thank You for Choosing Samsung
Thank you for choosing Samsung! Your new Samsung TV receiver represents the latest in
television technology. It has easy-to-use, on-screen menus and closed-captioning capabilities,
making this TV one of the best products in its class. This product will provide convenient,
dependable service and enjoyment for years to come.
Important Safety Information
To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in
mind when installing, using, and maintaining your machine.
• Read all safety and operating instructions before operating the TV receiver.
• Retain the safety and operating instructions for future reference.
• Heed all warnings on the TV receiver and in the operating instructions.
• Follow all operating instructions.
• Unplug the TV receiver from the wall outlet before cleaning, Use a damp cloth, Do not use
liquid or aerosol cleaners.
• Never add any attachments and/or equipment without approval of the manufacturer. Such
additions may cause risk of fire, electric shock, or other personal injury.
• Do not use the TV receiver where contact with or immersion in water is a possibility, such as
near bath tubs, sinks, washing machines, swimming pools, etc.
• Do not place the TV receiver on an unstable cart, stand, tripod,
bracket, or table. The TV receiver may fall, causing injury to
people and/or damage to the TV. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer or
sold with the TV receiver.
• Follow the manufacturer’s instructions when mounting the unit,
and use a mounting accessory recommended by the manufacturer.
Move the TV receiver and its cart with care. Quick stops, excessive
force, and uneven surfaces may cause the unit and cart to overturn.
• Provide ventilation for the TV receiver. The unit is designed with slots in the cabinet for
ventilation to protect it from overheating. Do not block these openings with any object, and
do not place the TV receiver on a bed, sofa, rug, or other similar surface. Do not place it near
a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that
there is adequate ventilation and that you’ve followed the manufacturer’s instructions for
mounting.
• Operate your TV receiver only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance dealer
or local power company.
• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized
alternating-current line plug having one blade wider than the other. This plug will fit into the
power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.
3
AA68-03173A_00(E)-PREFACE
9/15/03
11:27 AM
Page 4
• Protect the power cord. Power supply cords should be routed so that they will not be walked
on or pinched by items placed on or against them. Pay particular attention to cord placement
at plugs, convenience receptacles, and at the point where they exit from the unit.
• Unplug the TV receiver from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will
prevent damage to the unit due to lightning and power-line surges.
• An outside antenna system should not be placed in the vicinity of overhead power lines or
other electric light or power circuits or where it can fall into such power lines or circuits.
Avoid overhead power lines: When installing an outside antenna system, be extremely careful
to keep from touching the power lines or circuits. Contact with such lines might be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric
shock.
• Do not insert foreign objects through openings in the unit, as they may touch dangerous
voltages or cause damage. Never spill liquid of any kind on the TV receiver.
• Ground outdoor antennas. If an outside antenna or cable
system is connected to the TV receiver, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Read information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF
ANTENNA GROUNDING
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
• Do not attempt to service the TV receiver yourself. Refer all servicing to qualified service
personnel. Unplug the unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
- When the power-supply cord or plug is damaged
- If liquid has been spilled on the unit or if objects have fallen into the TV
- If the TV receiver has been exposed to rain or water
- If the TV receiver does not operate normally by following the operating instructions
- If the TV receiver has been dropped or the cabinet has been damaged
- When the TV receiver exhibits a distinct degradation in performance
• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the TV receiver to normal.
• When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
• Upon completion of any service or repairs to this TV receiver, ask the service technician to
perform safety checks to determine that the TV receiver is in a safe operating condition.
4
AA68-03173A_00(E)-CONTENTS
9/15/03
11:27 AM
Page 5
CONTENTS
Chapter 1: Your New TV . . . . . . . . . . . . . . . . 7
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Familiarizing Yourself with The TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2: Installation . . . . . . . . . . . . . . . . . 14
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . . 14
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . . 14
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . . 15
Separate VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . 15
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting to a Cable Box that Descrambles
All Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting to a Cable Box that Descrambles
Some Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting a VCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting an S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting a Second VCR to Record from the TV. . . . . . . . . 20
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting a Camcorder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installing Batteries in the Remote Control . . . . . . . . . . . . . . . . . . . . . . 22
Chapter 3: Operation . . . . . . . . . . . . . . . . . . 23
Turning the TV On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Plug &amp; Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Viewing the Menus and On-Screen Displays . . . . . . . . . . . . . . . . . . . . 25
Viewing the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . . 27
Storing Channels in Memory (Automatic Method) . . . . . . . . 28
Adding and Erasing Channels (Manual Method). . . . . . . . . . 29
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Directly Accessing Channels . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the PRE-CH Button to select the Previous Channel . . . 30
5
AA68-03173A_00(E)-CONTENTS
9/15/03
11:27 AM
Page 6
CONTENTS
Chapter 3: Operation (Cont...) . . . . . . . . . . . 30
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Labeling the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Customizing the Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using Automatic Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setting The On/Off Melody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Viewing a VCR or Camcorder Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Chapter 4: Special Features . . . . . . . . . . . . . 39
Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting Up Your Remote Control to Operate Your VCR . . . . . 39
Setting Up Your Remote Control to Operate Your Cable Box . . . 41
Fine Tuning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Using the Surf Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Setting the On/Off Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Sound Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Choosing a Multi-Channel Sound (MTS) Soundtrack . . . . . . 49
Extra Sound Settings
(Turbo Sound, Surround, or Auto Volume) . . . . . . . . . . . . . 50
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Viewing the Demonstration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Chapter 5: Troubleshooting . . . . . . . . . . . . . 53
Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 7
Chapter One
YOUR NEW TV
List of Features
Your TV was designed with the latest technology. This TV is a high-performance unit that
includes the following special features:
• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• Built-in, dual channel speakers
• A special sleep timer
7
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 8
YOUR NEW TV
Familiarizing Yourself with The TV
Front Panel Buttons
The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.
CT21M7W/CT25M6W
CT29V10MQ
CT25K10MQ/CT29K10MQ
CT21S8W
Œ MENU
Press to see an on-screen menu of your TV's features.
&acute; VOL – , +
Press to increase or decrease the volume.
Also used to select items on the on-screen menu.
ˇ CH ▼ and CH ▲
Press to change channels. Also press to select
various items on the on-screen menu.
8
&uml; Remote Control Sensor
Aim the remote control towards this spot on the
TV.
ˆ STAND BY indicator
Lights up when you turn the power off.
&Oslash; POWER
Press to turn the TV on and off.
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 9
YOUR NEW TV
Side Panel Jacks
You can use the Side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment,
see pages 14 - 21)
CT21S8W
CT21M7W/CT25M6W/
CT25K10MQ/CT29V10MQ/
CT29K10MQ
Œ AUDIO INPUTS
Audio signals from VCRs, DVD players and similar devices.
ˇ HEADPHONE
Connect a set of external headphones to this jack
for private listening.
&acute; VIDEO INPUT
Video signals from VCRs, DVD players and similar
devices.
9
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 10
YOUR NEW TV
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
Because there are two sets of input jacks, you can connect two different A/V
components (i.e., a VCR and a DVD, 2 VCRs, etc.)
For more information on connecting equipment, see pages 14 - 21.
Œ AUDIO-VIDEO MONITOR
OUTPUTS
These audio-video signals are identical to A/V
signals being displayed on the big screen.
(Typically used as the input signals for a recording VCR.)
ˆ S-VIDEO INPUT
Connect to an S-VHS VCR or DVD player.
&Oslash; DVD VIDEO INPUT
Connect video from a DVD player.
Note: Monitor Output doesn’t operate in the DVD
mode.
&acute; VIDEO INPUT
Video signals from VCRs, DVD players and similar
devices.
ˇ AUDIO INPUTS
Audio signals from VCRs, DVD players and similar
devices.
&uml; DVD AUDIO INPUTS
(INPUT 2)
Use these jacks to connect the audio signals
from a DVD player when using the DVD video
input jacks. When not using the DVD jacks, these
audio jacks function as audio for Video 2 or SVIDEO.
10
∏ VHF/UHF
Connect to an antenna or to a cable TV system.
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 11
YOUR NEW TV
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
You can also use your remote control to operate your VCR and cable box. See page 39
for details.
Œ POWER
&Ocirc; MODE
Turns the TV on and off.
Selects a target device to be controlled by the Samsung remote
control (i.e., TV, Set Top Box, VCR,
Cable box, or DVD).
&acute; S.MODE
Adjust the TV sound by selecting
one of the preset factory settings
(or select your personal, customized sound settings).
 PRE-CH
Tunes to the previous channel.
ˇ P.MODE
&Ograve; TV/VIDEO
Adjust the TV picture by selecting
one of the preset factory settings
(or select your personal, customized picture settings).
Press to display all of the available
video sources (i.e., Antenna/Cable,
VCR).
&Uacute; CH
and CH
(Channel Up/Down)
&uml; Number buttons
Press to select channels directly
on the TV.
Press CH
channels.
+100
to change
&AElig; INFO
Press to select channels over 100.
For example, to select
channel 121, press “+100,” then
press “2” and “1.”
ˆ VOL -, VOL
or CH
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
ı EXIT
+
Press the menu to exit.
Press to increase or decrease the
volume.
˜ Up,Down,Left,
Right (▲,▼,œ,√)/
ENTER
&Oslash; MUTE
Press to temporarily cut off
the sound.
Press to select highlight up, down,
left, or right. While using the onscreen menus, press ENTER to
activate (or change) a particular
item.
∏ SLEEP
Press to select a preset time interval for automatic shutoff.
&macr; TURBO
” MENU
Press to turn the TURBO sound On
or Off.
Displays the main on-screen
menu.
˘ MTS (Multichannel
Television Stereo)
’ P.SIZE
Press to change the screen size.
Your choices are Normal, Zoom.
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
˝ R.SURF
Press the R.SURF button to automatically return to a preferred
channel after a user-preset time
delay.
CT29K10MQ
11
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 12
YOUR NEW TV
Remote Control
&iquest; VCR Controls
˛ RESET
If your remote control is not functioning properly, take out the batteries and press the reset button
for about 2~3 seconds. Re-insert
the batteries and try using the
remote control again.
REW (Rewind)
Press to rewind a tape in your
VCR.
STOP
Press this button to stop a tape
during play, record, rewind or
fast forward. If the button is
pressed during Full-Automatic
play, the function will be cancelled.
PLAY/PAUSE
Press the PLAY/PAUSE button to
play back prerecorded tapes or
pause the tape.
FF
Press to fast forward the tape in
your VCR.
&cedil; SET
Use this button when you are setting up your remote control to
operate your Set Top Box, VCR,
Cable box, or DVD.
CT29K10MQ
12
AA68-03173A_00(E)-CHAPTER 1
9/15/03
11:29 AM
Page 13
YOUR NEW TV
Remote Control
Œ POWER
” PRE-CH
Turns the TV on and off.
Tunes to the previous channel.
&acute; Number buttons
’ TV/VIDEO
Press to select channels directly
on the TV.
Press to display all of the
available video sources (i.e.,
Antenna/cable, VCR).
ˇ +100
˝ CH
and CH
(Channel Up/Down)
Press to select channels over 100.
For example, to select
channel 121, press “+100,” then
press “2” and “1.”
&uml; VOL -, VOL
Press CH
channels.
+
or CH
to change
&Ocirc; INFO
Press increase or decrease the
volume.
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
ˆ SLEEP
 EXIT
Press to select a preset time interval for automatic shutoff.
Press the menu to exit.
&Oslash; MENU
&Ograve; Up,Down,Left,
Right (▲,▼,œ,√)/
ENTER
Displays the main on-screen
menu.
Press to select highlight up, down,
left, or right. While using the onscreen menus, press ENTER to
activate (or change) a particular
item.
∏ MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
&Uacute; R-SURF
Press the SURF button to automatically return to a preferred channel
after a user-preset time delay.
CT21M7W/CT25M6W/CT25K10MQ/
CT29V10MQ/CT21S8W
13
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 14
2
C h a p t e r Tw o
I N S TA L L AT I O N
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads” on page 15.
If you have two antennas, see “Separate
VHF and UHF Antennas” on page 15.
Antennas with 300-ohm Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from the
twin leads under the
screws on the 300-75 ohm
adaptor (not supplied).
Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the
VHF/UHF terminal on the
bottom of the back panel.
14
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 15
I N S TA L L AT I O N
Antennas with 75-ohm Round Leads
1
Plug the antenna lead into
the VHF/UHF
terminal on the bottom of
the back panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
2
Plug the combiner into the
VHF/UHF terminal on the
bottom of the rear panel.
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
Plug the incoming cable
into the VHF/UHF antenna
terminal on back of the TV.
Because this TV is cable-ready,
you do not need a cable box to view
unscrambled cable channels.
▼
1
15
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 16
I N S TA L L AT I O N
Connecting to a Cable Box that Descrambles All Channels
Find the cable that is connected to the ANTENNA
OUT terminal on your
cable box.
This terminal might be labeled
“ANT OUT”, “VHF OUT” or simply,
“OUT”.
▼
1
2
Connect the other end of
this cable to the VHF/UHF
antenna terminal on the
back of the TV.
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
Find and disconnect the
cable that is connected to
the ANTENNA IN
terminal on your cable
box.
2
Connect this cable to a
two-way splitter.
3
Connect a coaxial cable
between an OUTPUT terminal on the splitter and
the IN terminal on the
cable box.
16
This terminal might be labeled
“ANT IN”, “VHF IN” or simply,
“IN”.
▼
1
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 17
I N S TA L L AT I O N
4
Connect a coaxial cable
between the ANTENNA
OUT terminal on the cable
box and the B–IN terminal
on the A/B switch.
5
Connect another cable
between the other OUT
terminal on the splitter
and the A–IN terminal on
the RF (A/B) switch.
6
Connect the last coaxial
cable between the OUT
terminal on the RF (A/B)
switch and the VHF/UHF
terminal on the rear of the
TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the
A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is
usually channel 3 or 4.)
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 14 -16). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the back of
the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal on
the back of the VCR.
17
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 18
I N S TA L L AT I O N
3
Connect a coaxial cable
between the ANTENNA
OUT terminal on the VCR
and the antenna
terminal on the TV.
A coaxial cable is usually included with a VCR. (If not, check your local electronics
store).
4
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the AUDIO jacks
on the TV.
5
Connect a video cable
between the VIDEO OUT
jack on the VCR and the
VIDEO jack on the TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
18
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 19
I N S TA L L AT I O N
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
1
To begin, follow steps
1–3 in the previous
section to connect the
antenna or cable to your
VCR and your TV.
2
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the 2 AUDIO
INPUT jacks on the TV.
Make sure the jacks you are using are underneath the number “2”.
3
Connect an S-video cable
between the S-VIDEO OUT
jack on the VCR and the
S-VIDEO INPUT jack on
the TV.
An S-video cable is usually included with an S-VHS VCR. (If not, check your local
electronics store.)
19
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 20
I N S TA L L AT I O N
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR.
To do this, connect your second VCR as follows:
1
Connect a set of audio
cables between the
AUDIO OUT jacks on the
TV and the AUDIO IN
jacks on the VCR.
(The VCR input jacks might be either on the front or on back of the VCR.)
2
Connect a video cable
between the VIDEO OUT
jack on the TV and the
VIDEO IN jack on the VCR.
Refer to your VCR’s instructions for more information about how to record using this kind
of connection.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Note: Only 480i formats are supported.
1
Connect a set of audio
cables between the
AUDIO INPUT 2 jacks on
the TV and the AUDIO
OUT jacks on the DVD
player.
2
Connect a video cable
between the DVD-IN (Y,
Pb, Pr) jacks on the TV
and the DVD-OUT (Y, Pb,
Pr) jacks on the DVD
player.
Note: For an explanation of Component video, see your DVD player's owner's manual.
20
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 21
I N S TA L L AT I O N
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow
you to view the camcorder tapes without using a VCR. (Also see “Viewing a VCR or
Camcorder Tape” on page 38)
1
Locate the A/V output
jacks on the camcorder.
They are usually found on
the side or back of the
camcorder.
2
Connect an audio cable
between the AUDIO OUTPUT jack on the camcorder and the AUDIO
terminals on the side of
the TV.
3
Connect a video cable
between the VIDEO OUTPUT jack on the camcorder and the VIDEO terminal on the side of the
TV.
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
21
AA68-03173A_00(E)-CHAPTER 2
9/15/03
11:57 AM
Page 22
I N S TA L L AT I O N
Installing Batteries in the Remote Control
1
Slide the cover out completely.
Install two AAA size
batteries.
Replace the cover.
Remove the batteries and store
them in a cool, dry place if you won’t
be using the remote control for a
long time.
▼
3
Make sure to match the “+” and
“–” ends of the batteries with the
diagram inside the compartment.
▼
2
The remote control can be used up
to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
22
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 23
C h a pOtP EeR AT
r I OTN h r e e
O P E R AT I O N
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Plug &amp; Play Feature
When the TV is initially powered On, five basic customer settings proceed automatically
and subsequently: Setting the language, Video signal source, Ant. input check, Auto program, and Clock.
1
Press the POWER button
on the remote control.
The message “Plug &amp;
Play” is displayed.
It flickers for a little while
and then the “Language”
menu is automatically
displayed.
2
Press the œ or √ button
to select the desired language. Press the MENU
button to enter the language, and then the
“Channel” menu is automatically displayed.
3
Press the œ or √ button
to select the desired video
signal source.
Press the MENU button to
enter the video signal
source, and then the
“Ant Input check” is
automatically displayed.
continued...
23
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 24
O P E R AT I O N
4
Make sure that the
antenna is connected to
the TV. And then press the
œ or √ button to activate
&quot;Auto Program&quot; or
press the MENU button to
skip. (refer to “Auto
program” on page 28.)
5
Press the œ or √ button
to move to the hour or
minute. Set the hour or
minute by pressing the
▲ or ▼ button. (refer to
“Setting the clock” on
page 32.)
6
When you have finished,
press the MENU button.
The message “Enjoy your
watching..” is displayed.
7
If you want to reset this
feature
(1)Press the MENU button.
(2)Press the ▼ button
three times to select the
Function menu and
press the √ button.
(3)Press the ▼ button to
select Plug &amp; Play and
press the √ button.
The message “Plug &amp;
Play” is displayed.
Note: Plug &amp; Play feature doesn’t work when in the A/V mode.
24
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 25
O P E R AT I O N
Viewing the Menus and On-Screen Displays
Viewing the Menus
With the power on, press
the MENU button.
The on-screen menus disappear
from the screen after about thirty
seconds.
▼
1
The main menu appears
on the screen. Its left side
has four icons: Picture,
Sound, Channel, and
Function.
Use the ▲ and ▼ buttons to highlight one of the 4 icons.
Then press the √ button to access the icon’s sub-menu.
Press the MENU button to exit.
You can also use the MENU,
CHANNEL, and VOLUME buttons
on the control panel of the TV to
make selections.
▼
2
Viewing the Display
Press the INFO button.
on the remote control.
The on-screen display
shows any or all of the
following: Active channel,
Audio source and the
time.
The on-screen displays
disappear after about twelve seconds.
▼
1
When Closed Caption has been set,
the icon(
) will appear by pressing the Display button.
25
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 26
O P E R AT I O N
Selecting a Menu Language
1
Press the MENU button to
display the menu.
Press the ▼ button three
times to select “Function”,
then press the √ button.
2
Press the œ or √ button
to select the appropriate
language: English,
Spanish or French.
3
Press the MENU button twice to exit.
26
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 27
O P E R AT I O N
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH
and
CH
buttons to scan through the channels. This eliminates the need to change
channels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and
deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press MENU to
display the menu.
Press the ▼ button two
times to select “Channel”,
then press the √ button.
2
Repeatedly press the
œ or √ button to cycle
through these choices:
ANT (antenna),
STD, HRC or IRC (all cable
TV).
Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next
page).
3
Press the MENU button twice to exit.
27
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 28
O P E R AT I O N
Storing Channels in Memory (Automatic Method)
1
First, select the correct
signal source (ANT, STD,
HRC, IRC). See steps 1~2
on previous page.
Press the MENU button,
then press the ▼ button
twice to select “Channel,”
then press the √ button.
2
Press the ▼ button to
select “Auto program”.
The TV automatically cycles
through all of the available channels
and stores them in memory. This
takes about one to two minutes.
Press the MENU button at any time
to interrupt the memorization
process and return to the Channel
menu.
▼
3
Press the œ or √ button.
The TV will begin
memorizing all of the
available channels.
4
After all the available channels are stored, the Auto program
menu reappears. Press the MENU button twice to exit.
28
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 29
O P E R AT I O N
Adding and Erasing Channels (Manual Method)
1
Press the MENU button.
Press the ▼ button twice
to select “Channel”, then
press the √ button.
2
Press the ▲ or ▼ button
to select “Add/Erase”.
Press the √ button.
3
Press the œ / √ or number
buttons to select the channel you want added or
erased.
4
Press the ▲ or ▼ button
to select “Select”.
Press the œ or √ button
to select “Added” or
“Erased”.
Press the MENU button
three times to exit.
29
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 30
O P E R AT I O N
Changing Channels
Using the Channel Buttons
1
Press the CH
or CH
button to change channels.
When you press CH
or CH , the TV changes channels in sequence. You will see all the
channels that the TV has memorized. (The TV must have memorized at least three channels.)
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Use the number buttons to quickly tune to any channel.
1
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2”, then “7”.
The TV will change channels when you press the
second number.
When you use the number buttons, you can directly select channels that were either erased or
not memorized.
To select a channel over 100, press the +100 button. (For channel 122, press “+100”, then “2”,
then “2”.)
To change to single-digit channels (0–9) faster, press “0” before the
single digit. (For channel “4”, press “0”, then “4”.)
Using the PRE-CH Button to select the Previous Channel
Press the PRE-CH button.
The TV will switch to the last channel viewed.
To quickly switch between two
channels that are far apart, tune to
one channel, then use the number
button to select the second channel.
Then, use the PRE-CH button to
quickly alternate between them.
▼
1
Adjusting the Volume
Press the VOL + or VOL– button to increase or decrease the volume.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
1
Press the MUTE button and the sound cuts off.
The word “Mute” will appear in the lower-left corner of the
screen.
2
To turn mute off, press the MUTE button again, or simply press
either the VOL – or VOL + button.
30
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 31
O P E R AT I O N
Labeling the Channels
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”,
“PBS2”, CNN1”, etc.) A label consists of four fields, where each field is a letter, a number, “*”, or a blank. When the DISPLAY button is pressed, the channel label will appear
next to the channel number.
1
Press the CH
or CH
button to tune to the channel
that will be labeled.
Note: You cannot select
“Labeling” in the A/V mode.
▼
2
Press the MENU button to display the menu, then press the
▼ button to select “Channel”.
Press the √ button.
3
Press the ▼ button to select
“Labeling”.
Press the √ button to begin
labeling. The left-most field will
be highlighted.
(Each label has four fields.
See top paragraph.)
4
Press the ▲ or ▼ button to
select a letter, a number, “*”, or
a blank. (Pressing the ▲ button
results in this sequence:
A,B,...Z,*, blank,0,1,...9).
5
Press the √ button to switch to
the next field, which will be
highlighted. Select a second
letter or digit using the ▲ and ▼
buttons, as above. Repeat the
process to select the last two
digits.
Press the MENU button to set the label and clear the menus from
the screen.
31
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 32
O P E R AT I O N
Setting the Clock
1
Press the MENU button to
display the on-screen
menu.
Press the ▼ button three
times to select “Function”.
Press the √ button.
2
Press the ▼ button to
select “Time” menu.
Press the √ button: The
Time menu will appear on
the screen, and “Clock”
will be selected.
Press the √ button again
(the hours digits will be
selected). Press the ▲ or ▼
button repeatedly until the
correct hour appears.
When selecting the hours, be sure
to select the proper time of day (AM
or PM).
▼
3
You can change the hours by pressing
▲ or ▼ repeatedly (or by holding
down either of these buttons).
After the hour is entered,
press the √ button. (at this
point the minutes digits will
be selected.)
Press the ▲ or ▼ button
to select the
correct minutes.
After selecting the correct
minutes, press the √
button.
Press the MENU button
three times to exit.
32
The time will appear every time
you press INFO.
▼
4
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 33
O P E R AT I O N
Customizing the Picture
You can use the on-screen menus to change the contrast, brightness, tint, color, and
sharpness according to personal preference. (Alternatively, you can use one of the
“automatic” settings. See next page.)
1
Press the MENU button
to display menu.
2
Press the œ or √ button
repeatedly, until the word
“Custom” is selected.
(When Custom is highlighted, the words
“Adjust” will appear on
the screen.)
Press the ▼ button to
select “Adjust”, then
press the √ button. (The
words Color Tone,
Contrast, Brightness,
Sharpness, Color, and Tint
will appear on the
screen.)
Press the ▲ or ▼ button
to select a particular item.
The customer can select
“Normal”, “Warm” or “Cool” according to personal preference.
▼
3
After adjusting an item, the gauge
will automatically disappear (after
about 5 seconds).
▼
4
Press the œ or √ button
to increase or decrease
the value of a particular
item.
Press the MENU button
four times to exit.
33
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 34
O P E R AT I O N
Using Automatic Picture Settings
Your TV has three automatic picture settings (“Dynamic”, “Standard” and “Movie”) that
are preset at the factory. You can activate either Dynamic, Standard or Movie by making
a selection from the menu. Or, you can select “Custom” which automatically recalls your
personalized picture settings.
1
Press the MENU button to
display the menu.
2
Press the œ or √ button
to select the “Dynamic”,
“Standard”, “Movie” or
“Custom” picture setting.
•
•
•
•
34
Choose Dynamic for viewing the TV during the day or when there is brightlight in the room.
Standard: Optimal indoor screen condition.
Choose Movie when viewing the TV in low light, or when
playing video games.
Choose Custom if you want to adjust the settings according to personal preference (see “Customizing the Picture”, page 33.)
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 35
O P E R AT I O N
Customizing the Sound
You can use the on-screen menus to adjust the bass, treble, and balance according to
individual preference. (Alternatively, you can use one of the “automatic” settings. See
next page.)
1
Press the MENU button to
display the menu.
Press the ▼ button to
select “Sound” menu.
2
Press the œ or √ button
repeatedly, until the word
“Custom” is selected.
(When Custom is selected, the words “Adjust”
will appear on the
screen.)
3
Press the ▼ button to
select “Adjust”, then
press the √ button. (The
words Bass, Treble, and
Balance will appear on
the screen.)
Press the ▲ or ▼ button
to select a particular item
to be changed.
4
Press the œ or √ button
to increase or decrease
the value of a particular
item.
Press the MENU button
four times to exit.
35
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 36
O P E R AT I O N
Using Automatic Sound Settings
Your TV has four automatic sound settings (“Standard”, “Music”, “Movie” and “Speech”)
that are preset at the factory. You can activate any of them by making a selection from the
on-screen menu. Or, you can select “Custom”, which automatically recalls your personalized
sound settings.
1
Press the MENU button to
display the menu.
Press the ▼ button to
select “Sound” menu.
2
Press the œ or √ button
repeatedly to select the
“Standard”, “Music”,
“Movie”, “Speech” or
“Custom” sound settings.
•
•
•
•
•
36
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movies when watching movies.
Choose Speech when watching a show that is mostly dialogue (i.e., news).
Choose Custom to recall your personalized settings.
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 37
O P E R AT I O N
Setting The On/Off Melody
You can hear clear melody sound when the TV is powered On or Off.
1
Press the MENU button to
display the menu.
Press the ▼ button to
select “Sound” menu ,
then press the √ button.
2
Press the ▼ button to
select “Melody”, then
press the œ or √ button
to select the “On” or
“Off”.
3
Press the MENU button twice to exit.
37
AA68-03173A_00(E)-CHAPTER 3
9/15/03
11:56 AM
Page 38
O P E R AT I O N
Viewing a VCR or Camcorder Tape
You must select the appropriate mode in order to view the VCR or
Camcorder signal on the TV.
1
Press the MENU button to
display the menu.
Press the ▼ button twice
to select “Channel”, then
press the √ button.
2
Press the ▼ button twice
to select the “TV/AV”.
3
Press the œ or √ button .
You will switch between
viewing the signals coming from equipment connected to the TV’s A/V
jacks, and the TV signal.
4
Press the MENU button twice to exit.
38
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 39
Chapter Four
S P E C I A L F E AT U R E S
Customizing Your Remote Control
(CT29K10MQ)
Your TV comes equipped with a “universal” remote control. In addition to
controlling the TV, the universal remote can also operate a VCR, DVD and a cable box
(even if your VCR, DVD and cable box are made by manufacturers other than Samsung).
Note: The remote control might not be compatible with all DVD players, VCRs, and Cable
boxes.
Setting Up Your Remote Control to Operate Your VCR or DVD
1
Turn off your VCR.
Press the MODE button and make sure that the VCR (or DVD)
LED is illuminated.
The remote control has four
“modes”: “TV,” “VCR”, “Cable” and
“DVD.” Press the “MODE” button
to switch the remote control to the
“VCR” (or DVD) mode.
▼
2
3
On your Samsung remote control, press the SET button.
Enter 3 digits of the VCR (or DVD) code listed on the next
page for your brand of VCR (or DVD).
Make sure you enter 3 digits of the
code, even if the first digit is a “0.”
If more than one code listed, try the
first one.
▼
4
6
When your remote control is in
the “VCR” (or DVD) mode, the volume
buttons still control your TV’s volume.
▼
Once your remote control is set up, press the MODE button
any time you want to use the remote to operate your VCR (or
DVD).
▼
Press the POWER button on the remote control. Your VCR
(or DVD) should turn on. If your VCR (or DVD) turns on, your
remote control is now set correctly.
If your VCR (or DVD) does not
turn on, repeat steps 2, 3, and 4, but try
one of the other codes listed for the
brand of your particular VCR (or DVD).
If no other codes are listed, try each
code, 000 through 073.
5
When your remote is in the “TV”
mode, the VCR control buttons (PLAY,
PAUSE, etc.) will still operate your
VCR.
39
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
S P E C I A L F E AT U R E S
VCR Codes (CT29K10MQ)
DVD Codes (CT29K10MQ)
40
Page 40
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 41
S P E C I A L F E AT U R E S
Setting Up Your Remote Control to Operate Your Cable Box
1
Turn off your cable box.
Press the MODE button and make sure that the CABLE LED
is illuminated.
The remote control has four
“modes”: “TV”, “VCR”, “Cable” and
“DVD”.
Press the “MODE” button to switch the
remote control to the “Cable” mode.
▼
2
3
On your Samsung remote control, press the SET button.
Enter 3 digits of the cable box code listed below for your
brand of cable box.
Press the POWER button. Your cable box should turn on. If your
cable box turns on, your remote control is now “set up” correctly.
Once your remote control is set up, press the MODE button
any time you want to use the remote to operate your cable
box.
When your remote control is
in the “CABLE” mode, the volume buttons still control your TV’s volume. Also,
the VCR control buttons (PLAY, PAUSE,
etc.) will still operate your VCR.
▼
6
If your cable box does not turn on,
repeat steps 2, 3, and 4, but try one of the
other codes listed for your particular
brand of cable box (If no other codes are
listed, try each cable box code, 000
through 046).
▼
5
Make sure you enter 3 digits of the
code, even if the first digit is a “0.” (If
more than one code listed, try the first
one.)
▼
4
Cabl Box Codes (CT29K10MQ)
41
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 42
S P E C I A L F E AT U R E S
Fine Tuning Channels
Use fine tuning to manually adjust a particular channel for optimal reception.
1
Select the appropriate
channel.
Press the MENU button to
display the menu.
Press the ▼ button twice
to select “Channel” menu,
then press the √ button.
2
Press the ▼ button three
times to select “Fine
tune”, then press the √
button.
3
Press the œ or √ buttons
to adjust the fine tuning.
Press the MENU button to
resume normal viewing.
▼
4
To store the fine tuning
setting in the TV’s memory, press the ▼ button to
select “Select”.
Press the œ or √ button
to select “Added”.
To reset the fine tuning to
“0”, press the œ or √
button to select “Erased”.
42
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 43
S P E C I A L F E AT U R E S
Changing the Screen Size
1
Press the MENU button to
display the menu.
Press the √ button to
select the “Picture” menu.
2
Press the ▼ button to
select &quot;Size&quot;.
3
Press the œ or √ button
repeatedly to select
“Normal” or “Zoom”.
Press the MENU button
twice to exit.
•
•
Normal : Sets the picture to 4:3 normal mode. This is a standard TV screen size.
Zoom : Magnifies the size of the picture on screen.
43
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 44
S P E C I A L F E AT U R E S
Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital
Noise Reduction feature to help reduce any static and ghosting that may appear on
the screen.
1
Press the MENU button to
display the menu.
Press the √ button to
select the “Picture” menu.
2
Press the ▼ button to
select &quot;Digital NR.&quot;
Pressing the œ or √ button will
alternate between “On” and “Off”.
▼
3
Press the œ or √ button
to select Digital NR “On”.
Press the MENU button to
exit.
44
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 45
S P E C I A L F E AT U R E S
Tilt (CT29K10MQ)
Due to the Earth’s magnetic field there may be same minor image tilt depending on
the TV’s location. When this occurs, follow the steps below.
1
Press the MENU button to
display the menu.
Press the √ button to
select the “Picture” menu.
2
Press the ▼ button to
select &quot;Tilt&quot;.
3
press the œ or √ buttons
to adjust the Tilt.
Press the MENU button to
exit.
45
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 46
S P E C I A L F E AT U R E S
Using the Surf Feature
This feature allows you to set the TV to return to a particular channel after a certain
amount of time. For example, you may be watching a channel when commercials
start. You can set the Surf to “5 minutes”, then switch channels. After 5 minutes,
the TV will return to the original channel. To use the Surf:
1
While you are watching
the channel to which you
want to return, press the
R.SURF button. The onscreen display will read
“Surf off”.
2
Press the R.SURF button
again to set the timer in
thirty second intervals, up
to five minutes.
3
The time you set will begin counting down on the screen.
When the time runs out, the TV will return to the channel
you were watching when you set the timer.
46
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 47
S P E C I A L F E AT U R E S
Setting the On/Off Timer
▼
Before using the timer, you must
set the TV’s clock. (See “Setting the
Clock” on page 32.)
1
Press the MENU button to
display the menu.
Press the ▼ button three
times to select &quot;Function&quot;
menu, then press the √
button.
2
Press the ▼ button to
select &quot;Time&quot;, then press
the √ button.
When you set the hours, make
sure the correct time of day (AM or
PM) appears to the right of the hour.
▼
3
Press the ▼ button to
select &quot;On time&quot;.
Press the √ button to
select the “On time”
hours.
(The hours digits will be
highlighted.)
Press the ▲ or ▼ button
repeatedly to select the
appropriate hours (i.e., the
hour when the TV will turn
on.)
4
Press √ to select the “On
time” minutes.
(The minutes digits will be
highlighted.)
Press the ▲ or ▼ button
to select the appropriate
minutes.
47
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 48
S P E C I A L F E AT U R E S
To deactivate the “On time,”
select “Off” during this step.
▼
5
Press the √ button to
select “On/Off.”
Press the ▲ or ▼ button
to turn the on-timer “On.”
(Repeatedly pressing the
▲ or ▼ button will
alternate between on and
off.)
6
When finished, press the
√ button .
Absent Power Off
When you set the timer “On”, your
television will eventually be turned
off, if you do not operate any
controls during the 3 hours after the
TV is turned on by timer.
This function is available in only the
timer “On” mode and will prevent a
leakage accident or overheating,
caused by your TV left on for a long
time due to the timer “On” (when
you are away on holiday, for
example).
▼
7
To set the Off time, press
the ▼ button to select
“Off time.”
Press the √ button and
set the hours and minutes.
(Follow the same procedure as in steps 1~6
above.)
8
When finished setting the timer, press the MENU button
three times to exit.
Setting the Sleep Timer
The sleep timer automatically shuts off the TV after a preset time
(from 10 to 180 minutes).
After about 5 seconds, the sleep
display will disappear from the
screen, and the time interval will be
set.
▼
1
Press the SLEEP button on the remote control.
2
Press the SLEEP button repeatedly until the appropriate
time interval appears (any of the preset values from “Off” to
“180”).
48
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 49
S P E C I A L F E AT U R E S
Sound Features
Choosing a Multi-Channel Sound (MTS) Soundtrack
Depending on the particular program being broadcast, you can listen to stereo, mono, or
a Separate Audio Program. (SAP audio is usually a foreign-language translation.
Sometimes SAP has unrelated information like news or weather.)
1
Press the MENU button
to display the menu.
Press the ▼ button to
select the “Sound” menu,
then press the √ button.
2
Press the ▼ butto to
select “MTS”.
The text at the bottom of the
menu tells you if the incoming
audio is stereo, SAP, or mono.
▼
3
Press the œ or √ button
to select “Mono,” “SAP,”
or “Stereo.”
Press the MENU button
twice to exit
•
•
•
Choose Stereo for channels that are broadcasting in stereo.
Choose Mono for channels that are broadcasting in mono, or if you are
having difficulty receiving a stereo signal.
Choose SAP to listen to the Separate Audio Program, which is usually a
foreign-language translation.
You can also change the MTS setting by pressing the “MTS” button on the remote
control. (When you change channels, MTS is set to “Stereo” automatically.
To listen in ‘SAP’ or ‘Mono,’ change the MTS setting.)
49
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 50
S P E C I A L F E AT U R E S
Extra sound settings (Turbo Sound, Surround, or Auto Volume )
• Turbo Sound
Turbo sound suitably emphasizes both higher and lower bands of sound (and includes
other effects).
• Surround
“Surround” converts a monaural sound signal into two identical left and right channels.
Once the “Surround” is set to “On” or “Off”, the setting applies to the sound effects such
as Standard, Music, Movie and Speech.
• Auto Volume
Each broadcasting station has its own signal conditions, and so it is not easy for you to
adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the modulation signal is
low.
1
Press the MENU button to
display the menu.
Press the ▼ button to
select the “Sound” menu,
then press the √ button.
2
Press the ▼ button to
select “Turbo sound”.
3
Press the √ button to
select “On”.
Press the MENU button
twice to exit
You can set Surround and Auto volume the same way as setting Turbo
sound.
50
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 51
S P E C I A L F E AT U R E S
Viewing Closed Captions
Your TV decodes and displays the closed captions that are broadcast with certain TV shows.
These captions are usually subtitles for the hearing impaired or foreign-language translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions. Most pre-recorded commercial video tapes provide closed captions as well. Check for the closed caption symbol in your television schedule
and on the tape’s packaging:
.
1
Press the MENU button to
display the menu.
Press the ▼ button to
select the “Function”
menu.
Press the √ button.
2
Press the ▼ button to
select the “Caption”
menu, then press the √
button.
Misspellings and unusual
characters sometimes occur during
closed caption transmissions, especially those of live events. There may be a
small delay before captions appear
when you change channels. These are
not malfunctions of the TV.
▼
3
Press the œ or √ button
to turn closed captioning
on/off.
In caption mode, captions
appear at the bottom of the screen,
and they usually cover only a small
portion of the picture.
▼
4
Press the ▼ button to
select “Mode”.
Press the œ or √ button
to select “Caption” or
“Text”.
Depending on the particular broadcast, it might be necessary to
make changes to “Channels” and “Field”:
Use the ▲, ▼, œ and √ buttons to make the changes. (Follow
the same procedure as in steps 3~4 above.)
Press the MENU button three times to exit.
Different channels and fields
display different information: Field 2
carries additional information that
supplements the information in
Field 1. (For example, Channel 1
may have subtitles in English, while
Channel 2 has subtitles in Spanish.)
▼
5
In text mode, information unrelated
to the program, such as news or
weather, is displayed. Text often
covers a large portion of the screen.
51
AA68-03173A_00(E)-CHAPTER 4
9/15/03
11:58 AM
Page 52
S P E C I A L F E AT U R E S
Viewing the Demonstration
To become familiar with the various menus provided by your television, you can view the
in built demonstration.
1
Press the MENU button to
display the menu.
Press the ▼ button to
select the “Function”
menu.
Press the √ button.
2
Press the ▼ button to
select “Demonstration”
menu.
Press the √ button.
3
Each of the menu options
is displayed in turn.
When you wish to stop the
demonstration, press any
button on the remote control.
52
AA68-03173A_00(E)-CHAPTER 5
9/15/03
11:59 AM
Page 53
Chapter Five
TROUBLESHOOTING
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, then call your nearest service center.
Identifying Problems
Problem
Possible Solution
Poor picture
Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality.
Try another channel.
Adjust the antenna.
No picture or sound.
Try another channel.
Press the TV/VIDEO button.
Make sure the TV is plugged in.
Check the antenna connections.
No color, wrong colors or tints.
Make sure the program is broadcast in color.
Adjust the picture settings.
If the set is moved or turned in a different
direction, the power should be OFF for
at least 30 minutes.
Picture rolls vertically.
Adjust the antenna.
Check all wire connections.
The TV operates erratically
Unplug the TV for 30 seconds, then try
operating it again.
The TV won’t turn on.
Make sure the wall outlet is working.
53
AA68-03173A_00(E)-APPENDIX
9/15/03
11:28 AM
Page 54
APPENDIX
Cleaning and Maintaining Your TV
With proper care, your TV unit will give you many years of service. Please follow these
guidelines to get the maximum performance from your TV.
Placement
• Do not place the TV near extremely hot, cold, humid or dusty places.
• Do not place the TV near appliances with electric motors that create magnetic fields,
such as vacuum cleaners.
• Keep the ventilation openings clear; do not place the TV on a soft surface, such as
cloth or paper.
• Place the TV in a vertical position only.
Liquids
• Do not handle liquids near or on the TV. Liquids that spill into it can cause serious
damage.
Cabinet
• Never open the cabinet or touch the parts inside.
• Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or
chemicals.
• Do not put heavy objects on top of the cabinet.
Temperature
• If your TV is suddenly moved from a cold to a warm place, unplug the power cord,
and allow at least two hours for moisture that may have formed inside the unit to dry
completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the different
television systems that are in use around the world. A TV designed for one system may
not work properly with another system due to differences in the TV channel frequencies.
Specifications
Model
CT21S8W/ CT21M7W
50/60Hz
Frequency of Operation
54
CT29K10MQ
AC 100-240V
Voltage
Power Consumption
CT25M6W/CT25K10MQ/
CT29V10MQ
110W
130W
150W
AA68-03173A_00(E)-APPENDIX
9/15/03
MEMO
11:28 AM
Page 55
">
Hello! I am an AI chatbot specifically trained to assist you with the Samsung CT-29V10MQ User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Assistant typing
Assistant terminated
Related

Samsung CL-17K10MJ Manual de Usuario

Samsung LTN1735 LCD Television Owner's Manual

Samsung LTN 1535, LTN 1735 Owner's Instructions Manual

Samsung TX-P2665W TX-P2766, TX-P3066W TX-P3266, TX-P2664W TX-P2764, TX-P3064W TX-P3264 Owner's Instructions

Samsung LTN1535 Specification

Samsung ST-54T6 Quick start guide

Samsung TXM 1967, TXM 1367, TXM 1997 Color Television Owner's Instructions

Samsung TXM2792F & TXL2767 Color Television Owner's Instructions

Samsung TX-P Series Digital TV Owner's Instructions

Samsung CL-32Z40HM Manual de Usuario

Samsung CL-21M21EQ Specification

Samsung CT-29M16MQ User manual
