User manual | Location of controls AC connection

Location of controls
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
27)
28)
29)
30)
Leather handle
Memory button
Repeat/Ran button
Function button
Volume up/down knob
On/standby button
Mute button
Source button
Folder down/Alarm button
Folder up/Clk adj
Skip up
/down
button
Tuning knob
Play/pause
button
button
Stop
Snooze button
LCD display
USB socket
3.5mm headphone jack
SD card slot
CD door open/close
Remote sensor
Dial pointer
FM-stereo LED indicator
Tuner LED indicator
Alarm sound mode selector
Rod antenna
Band switch
AC socket
Battery compartment (main unit)
Battery compartment (clock back up)
Caution:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
This unit should not be adjusted or repaired by anyone except qualified service personnel.
Precautions for use
Installation
•
•
•
Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the main voltage and before all other connections have been
made.
Do not cover any vents and make sure that there is a space of several centimeters at the back of the unit for
ventilation.
AC connection
1.
2.
3.
Connect the one end of the detachable power cord to the AC socket (28) and the other end to the ac outlet.
When you first plug the unit into the mains, the unit will go into standby mode.
Turn on the unit by On/Standby button (6), the TUNER LED indicator (24) will light up.
DC connection
For DC operation, please insert 6 pcs size C (UM-2) battery at batter compartment (29) as below direction:-
1
Setting the clock
1.
2.
3.
Set unit in standby mode.
Press and hold the “Folder up/Clk-adj ” button (10) a second, The minute digit flashing on the LCD display(16). Press
skip up
or skip down
button (11) to set the correct minute. Press “ Folder up/Clk-adj ” button (10) to store
the correct minute.
or skip down
button (11) to set the correct minutes. Then
The hour digit will flashing, press the skip up
press “ Folder up/Clk-adj ” button (10) to store the correct hour.
The clock setting will automatically stored if no button is being pressed in a period of about 10 seconds
during clock setting mode.
To avoid the re-set of clock frequently when exchange the battery, please insert 2 pcs AAA size
(um-4) battery at the clock/alarm back-up battery compartment (30) in the direction as below
direction:-
Remark : Pull down the ribbon while insert the battery, this can help to release it easier when
changing the battery in the next time.
Listening to radio
Operation
1.
2.
3.
4.
Turn on the unit by On/Standby button (6), unit defaulted on Tuner mode and the TUNER LED indicator (24) will light
up.
Select the descried band by band switch (27)
Turn the tuning knob (12) to set the station frequency as desired.
adjust volume know (5) to the desired volume level.
Hints for best reception:-
FM : the receiver has rod antenna (26) hanging at the rear cabinet. this wire should be totally unraveled and
extended for best reception.
AM : the receiver has a built-in am bar antenna. If am reception is weak, slightly rotate or re-positioning of the unit will
usually improve the am reception.
FM-stereo reception
The FM-stereo LED indicator (23) will light up to show FM stereo program is receiving.
Playing CD/MP3 disc
Getting start
1.
2.
3.
Press Function button (4) to select CD mode.
Open the CD compartment by pressing the CD door open/close (20). Put a CD disc into the compartment and close
the CD door.
Focus search is performance if disc is inside. Total number of tracks is read.
Play / pause mode
1.
2.
Press the “ play/pause
” button (13) to start playback, the first track will start playback.
To interrupt, press the “ play/pause
” button (13) once, and the playing time will be freeze on the lcd display
(16). Press again to resume normal playback.
Stop mode
1.
If Stop button (14) is pressed during play or pause mode. Go to stop mode and display total number of track on the
LCD display (16).
Skip mode (skip up
1.
/skip down
)
During play or pause mode, if skip up
button (11) is pressed it will go to next track and display the track no. and
then continuous the play or pause mode.
2
2.
3.
During play or pause mode, if Skip down
button (11) is pressed, it will go back to the beginning of the track,
same track no. is display and continuous the play or pause mode.
After step 2, press skip down
button (11) again, it will go to the previous track and continuous the play or pause
mode.
For MP3 disc/file
1.
2.
3.
Place the MP3-CD to CD compartment. After focus search is performing, the total number of track will be shown on
the LCD display (16).
Press Skip up
or Skip down
(11) button to select the track number.
When the desired track and album is being selected, press the “ Play/Pause
” button (13) to start playback.
Remark
Press “ Folder up
or down
“ button (9/10) on main unit can select the MP3 folder directly.
The number of folder will display on LCD (16) for 1-2 seconds selected and then it will resume to the number of the
track being playback
Repeat/Random mode
Press the “ Rep/Ran “ button (3) during playback to select repeat and random function, a single track, single folder (MP3
only) or all the tracks can be played in difference mode as follow:-
For CD
(1) Repeat 1
(2) Repeat all track
Play mode
Repeat track
Repeat all
Random
Off mode
Indicator
on LCD display
REP
REP
RANDOM
--------------
(3) Random
(4) Off mode
For MP3 disc/file
(1) Repeat 1
Play mode
Repeat single track
Repeat single folder
Repeat all tracks
Random
Off mode
(2) Repeat 1 folder
Indicator
on LCD display
REP
REP &
REP
RAN
-----------------
(3) Repeat all tracks
(4) Random
(5) Off mode
flashing
Repeat play
You can listen the desired tracks or folder repeatedly by this function.
Random play
You can listen all the tracks in a random order by this function
CD / MP3 disc programming
Up to 20 tacks can be programmed for disc play in any order. Before use, be sure to press the stop button.
1. Set in CD mode.
2. Press the Memory button (2), “ MEMORY “ & “ P01 ” will appear and flashing on LCD display (16).
3. Select a desired track by using the Skip up
/Skip down
buttons (11).
4. Press the Memory button (2) to enter the track into the memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6. When all the desired tracks have been programmed, press “ Play/Pause
“ button (13) to play the disc in the
order you have programmed.
7. Press “ Stop
” button (14) to terminate program play.
Press “ Stop
” button (13) at CD stop mode to cancel all programmed memory until the “ MEMORY “ indicator
disappear on LCD display (16).
st
For MP3 disc / file, press the “ Folder up “ button (10) to select the 1 track of next folder directly and hence to speed
up the song selection.
The programming mode will automatically stop if no button is being pressed in a period of about 30 seconds after
pressing the Memory button (2).
3
Remark:MP3 track format requirement:Bit rate : 32 kbps~320kbps, sampling rate : 32kHz, 44.1kHz and 48 kHz decodable
-
The performance of playing MP3 disc is various from the quality of recording disc and the method of recording.
Furthermore, the searching lead-time for MP3-CD is longer than normal CD due to difference format.
Playback of MP3 song via USB storage media or memory card
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media
with USB connecting port or SD/MMC memory card.
1.
2.
Set the system at standby mode first or other function except USB/SD mode.
Plug-in the USB pen-drive with the face up & make sure it going into completely or insert
the memory card in the direction of the arrow as shown in the label on the underside of
the memory card slot cover. Insert straight without bending..
Connecting the USB upside down or backwards could damage the audio system
or the storage media (USB thumb driver/SD/MMC card). Check to be sure the
direction is correct before connection.
3.
Turn on the unit again by On/Standby button (6) and set press Function button (4) to select CD mode. Press Source
button (8) to change to USB or SD mode. The system will start reading the storage media automatically after
connecting, and LCD display (16) will show the total number of MP3 files being detected.
Repeat the same playback procedure as playing CD/MP3 disc as above.
4.
Remark
-
The system can detect and read the file under MP3 format only at USB or SD mode but not other music file format.
If connect the system to MP3 player via the USB socket, due to variances in MP3 encoding format, some
MP3 player may not be able to play via the USB socket. This is not a malfunction of the system.
USB port does not support connection with USB extension cable and is not designed for communication
with computer directly
Due to ErP stage two requirement and protect the environment. The unit will switch to standby mode
automatically once no any music playing over 15 minutes.
Removing of USB or memory card
To remove the USB turn off the power or switch the function mode to either cd or tuner mode first. For USB port – un-plug
it by pulling out the USB socket directly. For memory card – pull out the SD/MMC card straightly without bending.
Setting the alarm
This unit able to set the alarm and wake up by buzzer, Ocean or bird sound
1
Set unit in standby mode.
2. Press and hold the “Folder down/Alarm” button (9) a second, the minute digit flashing on the LCD display (16). Press
skip up
or skip down
button (11) to set the correct minute. Press “Folder down/Alarm” button (9) to store
the correct minute.
3. The hour digit will flashing, press the skip up
or skip down
button (11) to set the correct minutes. Then
press “Folder down/Alarm ” button (9) to store the correct hour.
4. Choose the wake up sound mode by Alarm sound mode selector (25).
Active/de-active timer function
1.
2.
Press the “Folder down/Alarm” button (9) repeatedly until the timer indicator is shown on LCD display (16).
To cancel alarm function by press again “Folder down/Alarm” button (9) until the timer indicator disappear.
Remark : When alarm sound press “ snooze ” button (15) once to terminate the alarm mode temporarily and it will alarm
again after 9 minutes on each press. To cancel the alarm mode, press the “Folder down/Alarm” button (9). If no
any button press during alarm, it will automatically stop after running one hour.
The alarm setting will be automatically stored if no button is being pressed in a period of about 10 seconds
during alarm setting mode.
4
Remote control transmitter control functions
Battery installation (battery not provided)
The infra-red transmitter require 2 pcs “ AAA “ batteries for operation
Button description
Repeat/Random
Press to active repeat/random function
Memory
Press to active program function
Play/pause
Press once to start playback and press again to stop playback
temporarily
Skip up
Press to select previous / next track or press & hold to perform
fast forward/backward function
/down
Stop
Press to terminate playback or cancel programmed tracks
Folder up /down
Press to skip up/down the MP3 folder
Source
Press to change mode between CD/SD/USB
5

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project