Secubest DKN A1052 R Small dome camera User’s Manual
Below you will find brief information for Small dome camera DKN_A1052_R. This camera offers several features such as adjustable zoom, focus and tilt, as well as motion detection and alarm input/output. It also supports SD card recording and DDNS registration.
PDF
Download
Document
Advertisement
Advertisement
Full HD IP Fixed Indoor Small Dome Camera User’s Manual Ver. 1.1 / 2013.06 Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference. Safety Information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning Precaution This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING Precaution To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. Operating t Before using, make sure power supply and all other parts are properly connected. t While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and contact your dealer. WARNING 1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product. Handling tDo not disassemble or tamper with parts inside the camera. tDo not drop the camera or subject it to shock or vibration as this can damage the camera. tClean the clear dome cover with extra care. Scratches and dust can ruin the quality of the camera image. 2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product. 3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause excessive heat generation or fire. Installation and Storage tDo not install the camera in areas of extreme temperature, exceeding the allowed range. tAvoid installing in humid or dusty environments. tAvoid installing in places where radiation is present. tAvoid installing in places where there are strong magnetic fields and electric signals. tAvoid installing in places where the camera would be subject to strong vibrations. tNever expose the camera to rain or water. 4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire. 5. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury. 6. Do not place conductive objects (e.g. screw drivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power sorce and contact the service center. Continued use in such a condition may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock. 2 Important Safety Instructions 1. Read these instructions. - All these safety and operating instructions should be read before the product is installed or operated. 2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference. 3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to. 4. Follow all instructions. - All operating and use instructions should be followed. 5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc. 6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s unstructions have been adhere to. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 3 Disposal of Old Appliances 1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interferenece at his own expense. 4 Introduction - Product & Accessories Screw & Plastic Anchor-2pcs Camera Manual CD Test Monitor Cable Focusing Cover Quick Manual NOTE: The ‘Test Monitor Cable’ is used to test the camera by connecting to a portable display. 5 Introduction - Part Name & Functions 5 Zoom Lever 6 Focus Lever 1 Dome Cover 7 Tilt Stopper Screw 8 Test Video Slot Micro SD Memory Card Slot 2 9 Audio In/Out Port Factory Reset Switch 3 10 Terminal Block 11 RJ-45 Connector 4 Main Body 1 Dome Cover Covers the inner cover, lens, and main body to protect them. 2 Micro SD Memory Card Slot 3 Factory Reset Switch All the settings will be restored to the factory default. Power On the unit and push the switch for 5 seconds. WARNING YOU WILL LOSE ALL DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE IP DOME CAMERA WILL BE SET TO ITS FACTORY RESETS. 4 5 Main Body Includes a lens, a connecting slot, a PCB board, screws and such. Zoom Lever Using this lever, the lens zoom can be adjusted and fixed. 6 6 Focus Lever The lens focus can be adjusted by rotating it left or right. Rotate it clockwise for fixing. 7 Tilt Stopper Screw Using this screw, the slope of the lens can be adjusted and fixed. 8 Test Video Slot Use it to connect the test video calbe. 9 Audio In/Out Port 10 Terminal Block Connect the power, alarm I/O device. 11 RJ-45 Connector Connect the crossover cable. Installation - Installation Before installing your camera, you have to read the following cautions. 1. You have to check whether the location can bear five times of the weight of your camera. 2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or fire. 3. When installing your camera, don’t allow any person to approach the installation site. If you have any valuable things under the place, move them away. 1 7 Disassemble the camera Detach the dome cover from main body by squeezing the front and back of dome cover. Installation - Installation 8 2 Making holes on the Ceiling Panel To pass cables through the ceiling and insert plastic anchor, drill holes on the ceiling panel. 3 Connecting Cables Connect the power, audio, alarm and network cables respectively. See the section 2 ‘Installation - Cabling’ for details. 4 Fix the main body Insert the plastic anchor into the hole and fix the main body on the ceiling by screw provided. Installation - Installation 5 Adjusting Camera Angle To achieve desired view direction and orientation, rotate 3-axis gimbal. To fix the setting, tighten the Tilt stopper screw. 6 Adjusting View angle By turning screws of the lens, decide the view angle. 7 Adjusting Focus and Zoom [1] Insert the focusing cover on the camera lens. [2] Adjust the focus and zoom of the video. [3] Remove the focusing cover after finishing the focusing and zoomimg. If adjust the focus and zoom without focusing cover, focus and zoom might out after attaching the dome cover. [2] [1] [3] 9 Installation - Installation 10 8 Attaching the Dome cover After aligning dome cover on to the main body properly, push the dome cover. 9 Detaching the Protection Film Detach the protection film from the dome cover after finishing all installation. Installation - Cabling 1 Alarm Input 4 Network 2 Relay Output 5 Audio Input 1 Alarm Input/Sensor It connects to IR sensor, IrDA sensor or door switch. If the sensor is activated, it can activate to work the alarm device. 2 Relay Output It connects to the alarm lights, siren or lamps, and it is activated according to the Setup menu setting. 3 Power Connection Please, check the voltage and current capacity of rated power carefully. 3 Power 6 Audio Output Connection 11 Rated Power Current Consumption PoE DC 12V 6W (IR Model: 7.5W) IEEE 802.3af Class 0 4 Network Connection Connect the crossover cable into the RJ-45. 5 Audio Input Connect the ‘Audio In’ cable of the camera to the device like microphone. and audio input device is activated according to the web-viewer. 6 Audio Output Connect the ‘Audio Out’ cable of the camera to device like speaker. Audio volume is controled according to the web-viewer. Installation - Inserting/Removing an SD Memory Card The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Micro Recommended SD Card Specification (Not Included) - Type: Micro SD (SDHC) - Manufacturer: Transcend, Kingston, Toshiba, Sanddisk - Capacity: 4~16G - Class: over Class 6 1 Inserting an SD Memory Card Insert the SD card in the arrow direction. Don’t insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card. 2 Removing an SD Memory Card Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. If you have saved data in the SD memory card, removing the SD memory card prior to setting record to OFF will cause damage to the data stored in the card. 12 Network Setup - Quick Start of Network Connection 11. Configure the IP Camera’s TCP/IP settings as you normally do any other PCs on your network by providing a proper IP address, subnet mask, default gateway, and DNS server. Please follow the steps below to complete the initial setup of the network function. Please do not power on the IP Camera until instructed. If this is a stand-alone unit with a direct connection to cable/DSL/ Broadband modem, input the addresses you have received from your ISP. If you have received no IP address from your ISP, select Dynamic and choose the proper settings. Temporarily disable any proxy servers configured in internet Explorer. If connecting the IP Camera directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP Camera and the IP Camera has been correctly connected to the modem. 12. The IP Camera utilizes five TCP ports - a Web Port, a Video Port, a Control Server Port, Audio ports. A Web Port is to utilize Internet Explorer, a Video Server port is to support the streaming video, a Control Control Port is to transmit to control commands and Audio Ports are to transmit and receive Audio data. If the IP Camera will be directly attached to a cable/DSL/Broadband modem or it has been assigned a static IP from your ISP, then leave the default port settings. If you are installing the IP Camera on a network, you must define a Web Port other than 80. The other ports, a Video Port, a Control Port, Audio Ports can remain unchanged. 1. In order to communicate with the IP Camera, access to PC/laptop and configure the PC. Keep a record of TCP/IP properties of the PC. (IP address, subnet mask, gateway, DNS, etc.) Current TCP/IP Settings IP Address Subnet Mask Default Gateway 13. If the IP Camera is connected to a network which utilizes a router, you must have Port Forwarding configured on your personal router to forward all ports to the IP address you have assigned the IP Camera. Primary DNS Server Secondary DNS Server (Option) If your PC obtains its IP address automatically, there is no need to record any information. 14. After configuring Port Forwarding on your router (if necessary), you may access your IP Camera on your local network by opening Internet Explorer and specifying the IP address and Web Port that you have assigned to the IP Camera. 2. Change the IP address of the host PC to 192.168.1.11 and subnet mask to 255.255.255.0 (leave all other entries blank) 3. Connect the IP Camera to your PC’s Ethernet port via the supplied crossover cable. (It does not matter what end is used for the PC) Example: http://192.168.0.200:8888 If you leave your Web Port set to 80, you don’t need to specify the port in the Address Bar to access to your IP Camera. 4. Power on the IP camera using the supplied power adapter. 15. Access your IP Camera via the Internet : 5. After 1 minute of power, verify a flashing ACTIVE indicator and a flashing or solid LINK indicator. After the corresponding indicator lights are properly displayed, open Internet Explorer. If you use a static IP address assigned by your ISP 1) Open Internet Explorer. 2) Type the IP of the IP Camera. 3) If you use a router, type the routers’ static IP and the web port number of the IP Camera. 6. Type - http://192.168.1.80 (the default IP of the IP Camera) into your address bar. 7. Default ID/Password to access IP Camera are both the word: admin. If you have a dynamic address provided by your ISP 1) Open Internet Explorer and visit the DDNS website. 2) Register the IP Camera. 3) Reboot the IP Camera. 4) Give the DDNS server 10 minutes to locate your IP Camera’s IP information. 5) Click the refresh button in the Internet Explore. 6) After your camera is connected, select your camera. 8. Familiarize yourself with the Viewer Interface Screen. 9. Locate the TCP/IP configuration under Setup. Supply the same ID and Password to enter Setup. (admin : admin) 10. Select STATIC under ‘Network Type’ . You will select Dynamic only if you are connecting the IP Camera directly to your cable/DSL/Broadband modem and your Internet Service Provider is supplying a dynamic address. If you have a network with other devices (such as PC/laptop, etc.) or a router, you will NEVER select Dynamic. 15 Network Setup - Initial Setup via a Crossover Cable 6. Now you will be able to access the viewer software within the IP Camera. This section provides a guide on how to connect the IP Camera to your PC/Laptop for initial setup. Please follow the instructions in the order below without skipping steps. Do not supply power to the IP Camera until instructed. In order to access the IP Camera’s firmware you will need to connect the Video Server to a PC or Laptop directly via the supplied crossover cable. Open Internet Explorer and type the IP address of 192.168.1.80 (default IP of the IP Camera from the factory) into the Address Bar of the web browser (as seen below). Press Enter. If a message box similar to the image below appears, choose ‘Try Again’. The message will vary depending on the operating system. 1. Before you begin, you must determine the current network/ INTERNET (TCP/IP) settings on the PC or laptop. Write down your entries below for quick reference. Current TCP/IP Settings IP Address Subnet Mask 7. Now you will be able to see the login screen for the IP Camera. Default Gateway Primary DNS Server Secondary DNS Server (Option) The 3 authorities are available : Administrator, Operator and Viewer. The authority setup is available in Setup. For information on how to determine your currents settings, see Appendix A. t7JFXFS t0QFSBUPS 0OMZNPOJUPSJOHJTBMMPXFE Most of the functions are allowed except ‘Setup’. t"ENJOJTUSBUPS"MMGVODUJPOTBSFBMMPXFE If you are obtaining an IP Address automatically, there is no need to write down the information. 2. To make the IP Camera to communicate with your PC, change your PC’s IP address and subnet mask. 8. The default ID and Password are both the word ‘admin’ (without the “ ”) You should change your IP address to 192.168.1.11 and change the subnet mask to 255.255.255.0 9. At any time if you are prompted to download ActiveX controls, Click ‘Yes’ as all contents are safe. Leave all other entries (Default Gateway, DNS Servers, etc.) blank. For information on how to change your IP address and subnet mask, see Appendix B. You will have to click ‘Yes’ twice to two individual prompts. This allows your video to be displayed in Internet Explorer. 3. After you have made the changes to your IP address and subnet mask, you may attach the IP Camera to your PC via the supplied crossover cable. Plug-in either end of the crossover cable into the PC’s network card and the other end into your IP Camera. 4. After connecting the PC and IP Camera using the crossover cable, power on the IP Camera by plugging in the power supply shipped with the IP Camera. 5. No longer than 1 minute after powering on the IP Camera, verify that the ACTIVE indicator light is flashing, and the LINK indicator light is flickering or solid. No longer than 1 minute after power on the IP Camera, verify that the ACTIVE indicator light is flashing and the LINK indicator light is flickering or solid. If they are not, read the FAQ. 16 Network Setup - DDNS Registration If you have DYNAMIC IP service from your Internet Service Provider (ISP), you can’t tell the current IP address of the IP Camera. To solve this problem, you have to register to our DDNS service. At first, you have to check if you are using dynamic addressing. If so, register your IP Video Server on our DDNS website before you configure, setup, or install the IP Camera. Even though your IP is not dynamic, you will get benefit if you register to DDNS. In this case, just remember ‘alex.net4c.net/gate1’ instead of complicated series of numbers like http://201.23.4.76:8078. For more details, contact our Support Center. To register IP Camera to DDNS, ‘Serial No.’ of the IP Camera should be known. The ‘Serial No.’ can be found in section 6 ‘Setup - DDNS’ menu. To use a public DDNS called ‘dyndns’ or ‘no-ip’, refer to the detail information on how to use the service. (Visit the web site : http://www.dyndns.com or http://www.no-ip.com) 17 Network Setup - Guide to Network Environment 5. The following descriptions are several basic network scenarios. Determine which scenario describes your network. If your network does not match one of the scenarios below and you are unsure how to setup your IP Camera, contact your network administrator and then call our Support Center. Please configure the IP Camera at the installation site. You must determine your network scenario in order to configure the IP Camera with the proper TCP/IP settings. This tutorial will guide you through the process. Before actually configuring the IP Camera, determine settings to be applied. Record those settings to be used to configure your IP Camera for reference. You cannot control the rectangular gray areas and only the ISP has access to the devices. When configuring your IP Camera, treat the IP Camera as another PC on your network. You will assign it several addresses and other TCP/IP properties to match your current network. This step-by-step tutorial will teach what IP addresses and network configurations should be assigned based on the network scenario. 1. Before you begin, locate any information and settings received from your Internet Service Provider (ISP). You may need to refer to these IP addresses at a later time during the configuration. Current TCP/IP Settings IP Address Subnet Mask Default Gateway Primary DNS Server Secondary DNS Server (Option) Static Dynamic If you were not given any IP addresses or the ISP was responsible for the setup and installation of your Internet connection, go to step 2. If you are not using a router on your network, your ‘Current TCP/IP Settings’ (from the previous section) and ‘Assigned IP Addresses from My ISP’ will be exactly the same. 2. You must determine whether the IP address is STATIC or DYNAMIC. At this moment, you are only concerned about the ISP. Did they provide you with a STATIC or DYNAMIC address? If you are unsure, contact your ISP. 3. Configure your IP Camera’s TCP/IP settings for network connectivity by selecting Setup from the main interface and selecting TCP/IP located on the left of the Setup screen. 4. If prompted for ID and Password, use ‘admin’ for both entries. The default web port number is 80. If port 80 is blocked by the ISP, a value between 1025 ~ 60000 should be used. If TCP port 80 is blocked, consult the ISP 18 Network Setup - Setup Case A, B Configure your IP Camera's TCP/IP properties as follows : Case A: Dynamic IP + Personal Router [Most SOHO] 1. Network Type : STATIC (even though you have Dynamic IP from your ISP, use STATIC on the IP Camera) Camera 2. Internet Address : A private IP address such as 192.168.0.200 (Example) PC You need to assign an IP address to the IP Camera just as you do with PC. Personal Router W/Intergrated Switch Phone Line or CATV The IP address you assign must be unique to your network and match your network as well. For information on how to choose a unique IP and match your network, read the FAQ. Cable/xDSL Modem (ISP Provided) The IP address you assign must be a private IP. For information on how to choose a private IP please, read the FAQ. Internet 3. Subnet Mask : 255.255.255.0 (Example) Case B: Static(Fixed) IP + Personal Router [Efficient] You must use the same subnet mask as the one you noted under ‘Current TCP/IP Settings’. Camera 4. Default Gateway : 192.168.0.1 (Example) This IP address must be the IP address of your router. (private or LAN side) PC Use the same Default Gateway you noted under ‘Current TCP/IP Settings’. Personal Router W/Intergrated Switch Public Line Gateway or Router at ISP 5. Preferred DNS Server : Use the 1st DNS Server from ‘Assigned IP Address from My ISP’. Internet If you did not receive any IP addresses from your ISP, contact the ISP and acquire the IP address of their DNS server. 6. DDNS Server : Use the DDNS server. This is the same site you will register later to accommodate dynamic IP from your ISP. 7. Web Port : 8888 Do not use the default port 80 as this number must be changed. You may select any number between 1025 ~ 60000. 8. Control Port : 7777 You may select any number between 1025 ~ 60000. 9. Video Port : 7778 You may select any number between 1025 ~ 60000. 10. Audio Transmit Port : 7779 You may select any number between 1025 ~ 60000. 11. Audio Receive Port : 7780 You may select any number between 1025 ~ 60000. 19 Network Setup - Setup Case C, D Case C: Static(Fixed) IP [Dedicated line directly to the IP Camera] Case D: Dynamic IP + DSL/Cable Modem [Connected directly to the IP Camera] Camera Camera Phone Line or CATV Cable/xDSL Modem (ISP Provided) Public Line Gateway or Router at ISP Internet Internet Configure your IP Camera's TCP/IP properties as follows : To connect the IP Camera directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP Camera and the IP Camera has been connected correctly to the modem. Then power on the modem, followed by the IP Camera. 1. Network Type : STATIC 2. Internet Address : A static IP address received from your ISP such as 24.107.88.125 (Example) Configure your IP Camera's TCP/IP properties as follows : You need to assign an IP address to the IP Camera just as you do with PC. 1. Network Type : DYNAMIC 3. Subnet Mask : Subnet mask assigned from your ISP such as 255.255.255.240 (Example) 2. DDNS Server : Use the DDNS server 4. Default Gateway : 24.107.88.113 (Example) This is the same site you will register later to accommodate dynamic IP from your ISP. Use the assigned default gateway from your ISP 3. Web Port : 80 5. Preferred DNS Server : Use the 1st DNS Server from ‘Assigned IP Address from My ISP’ You may select any number between 1025 ~ 60000. If you have not received any IP addresses from your ISP, contact them to acquire the IP address of their DNS server. 4. Control Port : 7777 You may select any number between 1025 ~ 60000. 6. DDNS Server : Use the DDNS server 5. Video Port : 7778 This is the same site you will register later to utilize our DDNS service. You may select any number between 1025 ~ 60000. 7. Web Port : 80 6. Audio Transmit Port : 7779 You may select any number between 1025 ~ 60000. You may select any number between 1025 ~ 60000. 8. Control Port : 7777 7. Audio Receive Port : 7780 You may select any number between 1025 ~ 60000. You may select any number between 1025 ~ 60000. 9. Video Port : 7778 You may select any number between 1025 ~ 60000. 10. Audio Transmit Port : 7779 You may select any number between 1025 ~ 60000. 11. Audio Receive Port : 7780 You may select any number between 1025 ~ 60000. 20 Network Setup - Port Forwarding After entering the correct TCP/IP settings, you are ready for ‘Port Forwarding’(Cases A, B). 1. Please record the TCP/IP settings of your IP Camera for future reference. You may need this information to access your IP Camera and to configure ‘Port Forwarding’. IP Camera TCP/IP Settings IP Address Subnet Mask Default Gateway Preferred DNS Server DDNS Server 8FC1PSU Control Port Video Port Audio Transmit Port Audio Receive Port 2. After clicking ‘Apply’, the system will prompt for a reboot. Please allow the system 50 seconds to reboot and accept the changes. After 50 seconds, close the configuration screen. The view will display ‘Trying to Reconnect’. If the ACTIVE light on the IP Camera has gone off and is now back on again flashing, the IP Camera has rebooted. After the system reboots completely, remove the power supply from the unit and close Internet Explorer. 3. Return your PC/Laptop TCP/IP properties to their original settings. 4. Before installing the IP Camera, you must use ‘Port Forwarding’ on your personal router (Cases A, B). You will need to forward 5 ports: t8FC1PSU t$POUSPM1PSU t7JEFP1PSU t"VEJP5SBOTNJU1PSU t"VEJP3FDFJWF1PSU All the ports will be forwarded to the IP address you assigned to the IP Camera. In the example above, you would forward: t t t t t For information on how to use ‘Port Forwarding’, please read Appendix C. 21 Network Setup - Starting IP Camera After forwarding correctly the Web Port, Video Port, Control Port and two Audio Ports through your router (if applicable), install the IP Camera in a proper location. 1. Locate the serial number located on the label attached to the bottom of the IP Camera, you will need this for DDNS registration. 2. Connect the IP Camera to your router or cable/DSL modem (per your network scenario) via a Cat5/5e UTP Ethernet network cable. 3. Supply power to the IP Camera. 4. After 1 minute, verify the IP Camera indicators: t"$5*7&'MBTIJOH t-*/,'MJDLFSJOH4PMJE 5. "GUFSDPOGJHVSJOH1PSU'PSXBSEJOHPOZPVSDPNQVUFS (if necessary), access your IP Camera on your local network by opening Internet Explorer and specifying the IP address and Web Port assigned to the IP Camera. Examples: http://192.168.0.200:8888 or http://24.106.88.123 If you left your Web Port set to 80, do not need to specify the port in the Address Bar to access the IP Camera. 6. Access your IP Camera via the Internet : If you use Case B, C 1) Open Internet Explorer. 2) Type the IP of the IP Camera. If you use Case A, D 1) Open Internet Explorer. 7JTJUUIF%%/4XFCTJUF 3) Register the IP Camera. 4) Give the DDNS server 10 minutes (MAX) to locate your IP Camera’s IP information. You may reboot the server to send an immediate request to our DDNS server. 5) After your camera is connected, select your camera. The difference between B and C is that B needs to set the port forwarding. Since the type of DDNS differs from the service type, refer to the related service site. 22 Web Viewer Screen - Basic Screen 2 3 4 5 6 7 8 1 Web viewer is optimized with Windows XP or above version and explorer browser. 5 Control tab button. Click it to extend the panel to control the function of web-viewer. See the next page for detail. 1 Live video display. This is the region for live video stream from the camera. 6 Full screen button. Click it to extend the live video to full screen. To return to normal mode, press ‘Esc’ or ‘Enter’ key. 2 Resolution. The resolution of video that displays currently on the screen. 7 Camera Setup popup button. Click it to open the Setup page to setup details of Lens, White Balance, Auto Exposure, image Backlight and etc. See the section ‘Camera Setup’ . 3 SD Card Search. Searching or Playing the Image which stored in the SD Card. 8 Event alert icon. If Alarm in and Motion detection are detected, below icons will appear. 4 Setup popup button. Click it to open the Setup page to setup details of IP camera like Video, Network, Events, System and etc. See the section ‘Setup’ . <Alarm Input> 23 <Motion Detection> Web Viewer Screen - Control Tab 1 1 When the image goes unsmoothly because of bad network connection, it stored image during setup time and shows the image on the live view screen. User will see the delayed images as much as setup time. 2 2 Video stream button. Select a stream produced from the camera between Stream 1 ~ 3 to display it in the live view screen. Refer the ‘Setup > Basic > Video’ to setup the Video Stream. 3 3 4 5 Capture button. Capture the live video in the form of BMP or JPG file. The location and file name of image can be decided after clicking this button. 6 Refer the ‘Setup > Basic > Backup’ to setup the type of Image. 7 4 Print Button. Print current live image to the printer connected to the PC. 5 Record Button. If you click this button, the current live video will be stored as AVI format file in your PC. During the recording, you cannot change the Video Format. If you change the Video Format, the recording will be stopped automatically. 8 If remained disk space of the HDD drive where the video is recorded is less than 1GByte, a warning message box regarding the disk space will be shown and the recording will be stopped automatically. To play the recorded video in the Windows Media Player, H.264 codec must be installed. Recorded files folder 6 Windows Vista & Windows 7 c:\user\(username)\AppData\LocalLow\ IP Network Camera\RECORD Windows xp, 2000 & Windows me, 98 :\My Documents\IP Network Camera\ RECORD\(MAC Address)\Stream1(or 2, 3, 4, 5)\(Date)\Date,Time_Filename.avi’. Alarm Input Status. It shows the Alarm Input status. If the status of alarm input becomes On state, the ‘Off’ button will be changed to ‘On’ button and event alert icon( ) is displayed on the ‘Live video display’. If alarm is removed, the alarm input status is reset. Regardless of alarm status, the Alert Icon will remain unless 'Event Display Clear' button is clicked. 24 7 Relay Out Button. Enable or Disable relay out function. 8 Event Display Clear Button. Remove Event Alert Icons result from Alarm Input or Motion detection. Web Viewer Screen - Control Tab 9 Speaker Control. Enable/Disable Audio stream received from the camera and Volume control of the speaker in the computer. 10 Mic Control. Enable/Disable the Audio stream to the camera. 11 Motion Detection. Enable or Disable motion detection function. ‘Area Setup’ below must be done in advance. 14 Event Alert Icon( ) appears on the screen if 'Motion Detection' is activated. Icon will remain unless 'Event Display Clear' button is clicked. While the motion detection is activated, this function is de-activated momentarily if the OSD and OSD menu is shown on the screen. Then, it is re-activated when the OSD and OSD menu is disappeared. 12 Sensitivity. Define the sensitivity of motion detection. If High is selected, it will detect very small motion while it becomes relatively insensitive when Low is selected. 13 Area Setup. Setup the target area of motion detection. 9 10 <How To Setup> 1) If ‘Set’ button is clicked, Live screen shows grids to help area setup. 2) By clicking or dragging mouse on the grids, create or erase the masks on the main view. 3) Motion detection is effective in the masked Area. 4) Save setting by clicking ‘Save’ button. 11 12 Area Setup is possible only on the Ch No.1 in the ‘Video Format’. If you change the video format, motion detection area will return the setup to the default. 13 Unmasked Area No Detection Masked Area Detection Effective 14 25 Hide Button. Hide all control panels extended. Camera Setup - Camera Setup Flickerless(Read Only) Day & Night Auto: In this mode, the IR cut filter is removed automatically depending on the light condition around. Day: In this mode, the IR cut filter is applied to the image sensor all the time. Thus, the sensitivity will be reduced in the dark light condition but the better color reproduction performance are obtained. Night: In this mode, the IR cut filter on the image sensor is removed all the time. The sensitivity will be enhanced in the dark light condition but the image is black and white. TDN BW Level It is a level to change Day mode into Night mode when Day & Night mode is Auto. TDN Color Level It is a level to change Night mode into Day mode when Day & Night mode is Auto. WDR / BLC WDR: This function is intended to provide clear live image even under back light circumstances when there are both very bright and very dark areas simultaneously in live video. BLC: When the background is too bright or the object is too dark, the backlight compensation will make the target object look clearer. Digital Slow Shutter The slower the shutter setting, the brighter the image is. However, the haunting can happen on the image when the object is moving fast. AGC Enhances the brightness of the image by amplifying gain when the illumination is low. DNR If reduces the noise caused by ‘AGC’ action. If set towards ‘HIGH’, the noise will be reduced but the ghost effect on moving objects will be increased. White Balance Auto: The color temperature is adjusted automatically between 2500K and 10000K. Auto-L: The color temperature is adjusted automatically between 2500K and 7000K. Auto-H: The color temperature is adjusted automatically between 4000K and 10000K. Preset: Color temperature of moment of select to Preset is set to WB in current environment. Manual: The color temperature and the R/B gain level can be set up manually. Bright Using this control, brightness of image can be adjusted to meet your preference. Kelvin This function is set to the range of color temperture to adjust the WB. Sharpness Using this control, sharpness of image can be adjusted to meet your preference. R / B Gain Mirror Reverse the video from side to side. Shutter If Shutter is set to Auto, shutter speed is adjusted automatically which refers to surrounding illumination. Flip Reverse the video from up to down. Shutter Speed If this speed is faster, the moving object can be photographed without the ghost effect. However, picture can be dark if there is no sufficient lighting. This menu is activated when Shtter is set to Manual. Mode This function will prevent flickering screen from the natural outdoor light or indoor light. 26 Setup - Video Setup 1 2 3 4 5 6 7 8 9 10 1 Live Video Channel Setup 4 Resolution Setup the multiple codec and Video according to the environment of installed camera. Using selected channel on the ‘Web-Viewer > Control Tab > Video Format’. CH No.1 and No.2 are the default CH, so they can't be changed. However, detailed category of default codec can be setup. CH No.3 is the user channel, and codec and detailed category of codec can be setup. Select the video resolution. Available resolution can be depends on the codec setup between the channels. 1080p/i 720p/i D1 2 Codec 4CIF Choose the video codec. According to the selected codec, the subcategories can be changed automatically. CIF QCIF NTSC 1920 x 1080 1280 x 720 720 x 480 704 x 480 352 x 240 176 x 120 PAL 1920 x 1080 1280 x 720 720 x 576 704 x 576 352 x 288 176 x 144 <Resolution of Video Format> 3 Description Input the additional description about the selected channel. Max. 15 alphabets are allowed(Including space). For the description, English Alphabets, numbers and special characters ( / ~ ` ! @ $ ^ ( ) _ - { } [ ] ; , ) can be used. 5 Frame Rate Select the maximum Frame Rate. Available Frame Rate can be different although same codecs were set up. 27 Setup - Video Setup 1 2 3 4 5 6 7 8 9 10 6 Bitrate Mode 8 GOP(Group of Pictures) Size Set up the number of frames (P-frame) which contain only changed information based on basic frame (I-frame). Regarding videos with lots of movement, if you set GOP size bigger, only the number of P-frames is bigger. As a result, video resolution will be low but ‘File size’ and ‘Bit-rate can be decreased. Select the bit rate control scheme of video compression from CBR (Constant Bit Rate) or VBR (Variable Bit Rate). CBR To guarantee the designated constant bit rate, the quality of video are controlled in this mode. Therefore, the quality of video is likely to be varying when network traffic is changing. GOP(Group of Pictures) Size is.. I-frame and P-frame can be created for MPEG4 and H.264 video compression. I-frame(=key-frame) means the whole image data for one specific scene of video. P-frame is image data which has been changed information compared to I-frame GOP is made up of one I-frame and corresponding several P-frames. To improve video quality, set the number of P-frames smaller and to decrease image size, set the number of P-frames bigger. VBR To guarantee the designated quality, the bit rate of video stream is changed in this mode. Therefore, the frame rate of video is likely to be varying when network traffic is changing This category won't be appear if you select the codec. 7 Target Bitrate If Bitrate Control is set to be CBR, you can set the Target Bitrate. ............................................................................................................ 9 Video Output(Optional Function) Quality For VBR control mode, The Target Quality of video can be setup. To check the display output status during the installation, 'On' status is required. Recommend 'Off' status after installation. 10 Click ‘Apply’ to make above setting effective. Click this button when completed setup each channels. 28 Setup - Audio Setup 1 2 3 1 Input Gain Adjust the input gain of audio. 2 Output Gain Adjust the output gain of audio. Output gain 0 is mute. 3 Click ‘Apply’ to make above setting effective. 29 Setup - TCP/IP Setup 1 2 3 4 5 6 7 8 1 Network Type 5 Preferred DNS Server Define network IP address type from the Static Mode for the fixed IP or the Dynamic Mode by the dynamic IP address. If you select the Static Mode, you must fill out IP Address, Subnet Mask, Gateway, DNS Server and all ports. If you select the Dynamic Mode, the IP address will be allocated automatically by DHCP equipment. If you click the Apply button to update changes, the system will be re-booted. In this case, you have to reconnect the camera using new IP address. Define the DNS server IP address. Format is same as the IP address. 6 Port There are five ports in the camera providing different services. To get those services separately, unique port number must be assigned to each servers. 7 IPv6 Setting Create the IPv6 address. If you click the Apply button after checking the Enable check box, the system will be re-booted. If you re-visit this screen after finishing reboot, IPv6 address will be shown. 2 IP Address Define the IP address. The address is consisted of four numbers separated by dots and the range of each number is from 0 to 255. To use IPv6, network camera has to connect with the router for IPv6. 3 Subnet Mask Define the Subnet Mask. Format is same as the IP address. 8 Click ‘Apply’ to make above setting effective. 4 Default Gateway If the network type is dynamic, the IP address is changed in below cases. Therefore, the IP address needs to be searched again, and the camera needs to be reconnected in these cases. Default the Gateway IP Address. Format is same as the IP address. - When the camera power is on/off. - After Firmware update, Default set and reboot. 30 Setup - DDNS Setup 1 2 3 4 1 DDNS Disable If it is selected, DDNS service does not work. 2 Basic DDNS Please register the camera in net4c site so as to use net4c DDNS. Insert the serial number shown on the screen in the serial entry field. 3 Public DDNS To use public DDNS service, select a site address listed in the list. After filling out the Host Name of the site, the setup is completed by entering User Name and Password registered in that DDNS site. DDNS Provider Site Address DynDNS www.dyndns.com No-IP www.no-ip.com If you setup DDNS properly, the IP address of your camera will be updated automatically whenever IP address is changed or system is rebooted. If IP updating to DDNS site is failed, camera will keep retrying in 1min. interval. 4 Click ‘Apply’ to make above setting effective. 31 Setup - HTTPS Setup 1 2 3 2 Install a public certificate 1 Secure Connection System Secure Connection System chooses a method of security connection. A certificate issued by Certificate Authority can be installed to the camera and the installed certificate can be deleted. HTTP HTTP mode does not use a security connection method. <How to install or delete the certificate> 1) Input the description(name) of a certificate. 2) Click ‘Install’ button after selecting the certificate files and key file to be installed. 3) To remove the certificate files, click ‘Delete’ button. HTTPS (Secure connection mode using a unique certificate) This mode is a security connection method which uses the (temporary) certificate in the camera. While using HTTPS (Secure connection mode using the public certificate) method, the certificate cannot be deleted. HTTPS (Secure connection mode using the public certificate) This mode is a security connection method which uses a certificate issued by certificate authority. 3 Click ‘Apply’ to make above setting effective. HTTPS (Secure connection mode using the public certificate) method can be selected only if a certificate has been already installed. When HTTPS mode is chosen, input https://<IP Address> to connect to the camera. 32 Setup - SNMP Setup 1 2 1 SNMP V3 Secure Setup - The information of camera system can be known and configured with SNMP. - The changes for configuration use version 3 and username and password should be certified at that time. Username Username is the information of user account for user authentication. Authentication Password(MD5) The Authentication Password (MD5) is an encryption for authentication and they are at least 8 digits and up to 30 digits allowed. Privacy Password(DES) Information protection password is a private encryption and they are at least 8 digits and up to 30 digits allowed. 2 Click ‘Apply’ to make above setting effective. 33 Setup - Status This menu will show you all the information of Network setting in the camera. However, you cannot change those here. 34 Setup - Alarm Input Setup 1 2 3 4 3 Action 1 Input Device Setup Select input device type from OFF / N.O. / N.C. Define a counter action from Alarm Output / Alarm Image Transfer / Camera Action when Alarm Input is detected. Operation Off Ignore this Input sensor. NO The contact is normally open and closed when activated. NC The contact is normally closed and open when activated. 2 Activation Time Description Alarm Image Transfer Turn ON / OFF Image Transfer. Send image via E-mail or FTP server. (For more detail see Transfer Setup in this chapter) Alarm Output Activate alarm out (relay). Output Duration Select activation time from Always / Only Scheduled Time. Always Action Select time duration to maintain output. An alarm event is activated whenever sensor Input is detected. 4 Click ‘Apply’ to make above setting effective. Only An alarm event is activated only when sensor Scheduled Time input is detected during the scheduled time. To setup the schedule, you need to define Start time and End time followed by selecting Days. If End time is earlier than Start time, End time is regarded as next day. Ex) Assume you select Tue. If you set Start time as 16:00 and End Time as 09:00, Alarm Input will work from 4:00pm Tue to 9:00am Wed. 35 Setup - Motion Detection Setup 1 2 3 2 Action 1 Activation Time Select activation time from Always / Only Scheduled Time. Always Define a counter action from Alarm Output / Alarm Image transfer when motion is detected. An alarm is activated whenever motion is detected. Action Description Only An alarm event is activated only when motion Scheduled Time is detected during the scheduled time. Alarm Image Transfer Turn ON / OFF Image Transfer. Send image via E-mail or FTP server. (For more detail see Transfer Setup in this chapter) To setup schedule, you need to define Start time and End time followed by selecting Days. Alarm Output Activate alarm out (relay). Output Duration If End time is earlier than Start time, End time is regarded as next day. Ex) Assume you select Tue. If you set Start time as 16:00 and End Time as 09:00, Alarm Input will work from 4:00pm Tue to 9:00 am Wed. Select time duration to maintain output. 3 Click ‘Apply’ to make above setting effective. 36 Setup - Schedule Setup 1 2 3 4 3 Activation Time Schedule function enables to transfer series of still images in a time interval specified via E-mail or FTP. (For more detail, see ‘Transfer Setup’ in this chapter) Select activation time from Always / Only Scheduled Time. Always 1 Enable / Disable Transfer image at all times. Only Scheduled Time Transfer image during the scheduled time. Set Schedule function to be enabled or disabled. Schedule function enables to transfer series of still images in a time interval specified. To setup ‘Only Scheduled Time’, you need to define Start time and End time followed by selecting Days. The setup schedule is repeated every week. 2 Transfer Interval Define time interval of image transfer. If End time is earlier than Start time, End time is regarded as next day. Ex) Assume you select Tue. If you set Start time as 16:00 and End Time as 09:00, Alarm Input will work from 4:00pm Tue to 9:00am Wed. 4 Click ‘Apply’ to make above setting effective. 37 Setup - Transfer Setup 1 2 3 4 1 Transfer Mode 4 Click ‘Apply’ to make above setting effective. Image Transfer method is selected from FTP and E-Mail (SMTP). To use image transfer, FTP and SMTP in the next sections must be configured properly. 2 SD Card Record If it is set to On, the image is saved into the SD card as well. It will setup OFF automatically when SD card doesn't applied. The SD card setting can be configured on the SD CARD section. 3 Pre/Post Alarm Image Image Transfer due to event is configured by setting Image transfer rate and Pre/Post alarm duration. Descriptions Number of Image Define Number of image transferred per second. Pre-alarm Duration Define duration of image transfer before an event. Post-alarm Duration Define duration of image transfer after an event. Range of Pre/Post alarm duration can be changed according to Number of image setting. 38 Setup - FTP Setup 1 2 3 4 5 6 7 4 Port To transfer/save the image to the relevant sites through FTP, then FTP needs to be setup. Define the FTP Server Port. If Port is not appropriate, it is impossible to access to FTP Server. 1 Use Passive Mode 5 User ID Check it to use Passive mode for FTP transfer. If it is not check, the transfer becomes Active Mode. However, if you select active mode, it is possible that there might be problems due to the firewall. Consult with your network manager. Define User ID to access to the FTP Server. Fill out the correct User ID registered in the FTP Server. 6 Password In Active mode, the FTP transfer might not work due to the firewall. In this case, ask to the network administrator. Define Password to access to the FTP Server. Fill out the correct Password registered in the FTP Server. 2 FTP Server Address 7 Click ‘Apply’ to make above setting effective. Define FTP Server IP Address. If IP Address form is incorrect, a Message box will be shown to try again. Refer the above screen image for the example. 3 Upload Path Define a path in FTP server to store video. For the path name, English Alphabets, numbers and special characters aC #AB^`>@can be used. 39 Setup - SMTP Setup 1 2 3 4 5 6 7 8 9 10 6 E-Mail Sender To send/save the image to the relevant sites by Email, SMTP needs to be setup. Define the e-mail address of E-Mail Sender. It will be displayed as the sender when the camera sends an E-mail. 1 Plain, SSL/TLS 7 E-Mail Receiver Select Security mode of SMTP from Plain or SSL/TLS. After checking account setup of your SMTP Server, you may select one. Define the e-mail address of E-Mail Receiver. It will be displayed as the Receiver when the camera sends an E-mail. 2 SMTP Server Address 8 Title Define the SMTP Server Address. If the IP Address form is incorrect, a Message box will be shown to try again. Define the title of the E-Mail when the camera sends an E-mail. The title of the Email is limited to 40 characters including the spaces. 3 Port Define the Port used in the Plain or SSL/TLS security mode in the above. 9 Message Define the contents of E-Mail when camera sends an E-mail. 4 User ID The message of the Email is limited to 40 characters including the spaces. Define the User ID to access to SMTP Server. Fill out the correct User ID registered in the SMTP Server. 10 Click ‘Apply’ to make above setting effective. 5 Password Define the Password to access to SMTP Server. Fill out the correct Password registered in the SMTP Server. 40 Setup - SD CARD Setup 1 2 3 4 5 6 4 Capacity Warning E-mail 1 Total size / Free size Total capacity of SD card and the remainder of it are displayed. If it is set ON and remained space of SD card reach to less than 8MB, a warning e-mail will be sent to the e-mail account set in SMTP menu. 2 Format 5 Overwriting Mode Delete the all contents that stored in SD card. If it is set ON and remained space of SD card reach to less than 8MB, new data will start to be overwritten on the oldest data. However, if it is set OFF and remained space of SD card reach to less than 8MB, image recording will be stopped. If the SD card doesn't applied, ‘Format’ button will be deactivated. 3 Auto Delete Select the period for Auto delete. The image data stored before period will be deleted automatically. NONE Do not use ‘Auto Delete’. 1 Week Delete all stored image older than 1 week from 00:00 today. 1 Month Delete all stored image older than 1 Month from 00:00 today. 1 Year 6 Click ‘Apply’ to make above setting effective. Delete all stored image older than 1 Year from 00:00 today. It is noted that this function will be executed everyday to delete data before designated period. 41 Setup - Users Setup 1 2 3 4 3 Modify 1 Users List all the user accounts for authentication. Modify the information of the user accounts registered. For admin account, only Password and Auto Login function can be modified. 2 Add Register a new user 4 Delete Delete the selected user account. Admin account cannot be deleted. ID Password Verify Enter a new user ID except Admin since it exists. Enter the user Password. Enter the user Password again for verification. User Level Select Operator or Viewer. t7JFXFS t0QFSBUPS : Only monitoring is allowed. : Most of the functions are allowed except ‘Setup’. t"ENJOJTUSBUPS"MMGVODUJPOTBSFBMMPXFE Auto Login If you check the auto login for an account, this account becomes the public account. From the next login, everybody can access the camera using this account without authentication. Only one account can have the Auto Login. The ID and Password are limited to 10 characters. 42 Setup - Date/Time Setup 1 2 3 4 5 4 Synchronize with the time server 1 Current Date & Time Shows the current date and time setting in the Camera. In this mode, date/time is automatically updated using the Time Server selected. After selecting the Time Zone properly, Time Server must be selected. However, if you want to assign a time server not in the list, select Manual. Once synchronization is configured successfully, the time and date will be updated every 1 hour automatically. 2 Synchronize with my computer Set the date/time using those of PC currently connected. 3 Setup manually Set the date/time by typing manually. 5 Click ‘Apply’ to make above setting effective. 43 Setup - Firmware Update 1 2 3 1 Firmware Version Warning: 1. Do not turn off the power of camera during the Firmware update. Otherwise, the system can be stuck to be unstable. If updating is finished, the system will be rebooted automatically. It shows the current Firmware Version in the system. 2 Firmware Filename Designate the Firmware file name in your computer by clicking [Browse…] button. 2. Please make sure to check the ‘Notice’ shown on screen. If firmware update is completed, the camera will reboot automatically and ‘Setup window’ will be closed 3 Start Update Click this button to start update. Progress of uploading will be displayed using Progress Bar. If you assign the wrong file name, an error massage will be shown. 44 Setup - Default Set 1 2 1 Reset to the Factory Defaults Return the setup to the Factory Default. All Reset all Settings to the Factory Defaults. Except Except Network related settings, reset all Network Settings others to the Factory Defaults. Warning: If you click ‘Apply’, you will lose all setting data. If needed, please, make a note for further installation. 2 Click ‘Apply’ to make above setting effective. It takes approximated 4 minutes after clicking ‘Apply’ for the Default Set. 45 Setup - Restart If you click the ‘RESTART’ menu, a message box will be shown to confirm. Click the ‘Ok’ button to restart. 46 Setup - Log System Start, Network Connection Status(Including IP Address), Changing System Time, Changing Video Setup, Network Setup and Event(Alarm / Motion) Alert will be recorded. 1000 PCS of Log can be stored and the recorded data won't be deleted. 47 SD Card Search - Search 3 1 2 4 5 1 Date of stored image Choosing the date to find the stored events. 2 Stored Events(Schedule / Motion / Alarm) The interval of stored time and number of stored images in the Event Setup can be different. 3 Page No. of searched Images The latest page will be loaded at the head. 4 Stored Images Image will be stored by value at CH No. 2 in ‘Setup>Video configuration’. By clicking the image, see the image on the larger screen. 5 Stored Time of Images The interval of stored image can be setup depending on the each Events. 48 Appendix A : Current TCP/IP Settings If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your IP address. For information on how to do this, please read the FAQ. 1. Windows 98 / ME Users 2. Windows 2000 or XP Users 3. Windows Vista or 7 Users Start Start Start Setting Control Panel Control Panel Control Panel Network and Dial-up Connection or Network Connection Network and sharing center Network Configuration Tab Right-click Local Area Connection Manage network connections Properties Select the TCP/IP 10/100 Protocol Click Properties Note the settings under the IP Address, DNS Configuration, and Gateway tabs Properties Select the TCP/IP in General Tab Select either Internet Protocol Ver.4 (TCP/IPv4) or Internet Protocol Ver.6 (TCP/IPv4) Click Properties Click Properties Under the ‘General’ tab of the TCP/IP Properties you will see your IP address information. 49 Under the ‘General’ tab of the TCP/IP Properties you will see your IP address information. Appendix - B : Changing IP address and subnet mask 1. Windows 98 / ME Users 2. Windows 2000 or XP Users 3. Windows Vista or 7 Users Start Start Start Setting Control Panel Control Panel Control Panel Network and Dial-up Connection or Network Connection Network and sharing center Network Configuration Tab Right-click Local Area Connection Manage network connections Properties Select the TCP/IP 10/100 Protocol Click Properties Select 'Use the following IP address' and change the IP address and Subnet Mask. Properties Select the TCP/IP in General Tab Select either Internet Protocol Ver.4 (TCP/IPv4) or Internet Protocol Ver.6 (TCP/IPv4) Click Properties Click Properties Select 'Use the following IP address' 50 Select 'Use the following IP address' Appendix - C : Port Forwarding 2. For Linksys BEFSR41 Cable/DSL routers: After assigning the IP Camera a web server port and video server port you must use Port Forwarding. (for cases A, B) Please consult your router’s user guide on how to correctly configure Port Forwarding. For your convenience, we have provided two example configurations. 1) Open a web browser and type http://192.168.1.1 into you Address bar. (the default IP address to access the router) 2) You will have to supply your User Name and Password to log onto the router. Default from factory (User Name:[leave blank] Password: admin) 3) Select “ 4 Applications & Gaming” from the menu bar. 4 1. For D-Link DI-604 broadband routers: 1) Open a web browser and type http://192.168.0.1 into your Address bar. (the default IP address to access the router) 2) You will have to supply your User Name and Password to log onto the router. Default from factory. (User Name: admin Password: [leave blank]) 3) Select the “ 1 Advanced” tab and click " menu. 1 2 Virtual Server" 2 4) Input port numbers in " 5 Port Range" as below and click “ 6 Save Setting” button. Both of Web Server Port and Video Server Port should be added. The example is as below. 5 4) Click " 3 Apply" button after inputting proper values. The example is as below 6 Enabled / Disabled Input IP Camera Web Server Port and Video Server Port. 3 Start / End Enabled / Disabled Select “Enabled”. Name Input IVS name. Private IP Select “TCP”. Private Port / Public Port Input IVS Web Server Port. Schedule Select “Always” Start should be same as End. Both of Web Server Port and Video Server Port should be added. Input IVS address. Protocol Type Input IP Camera name. 5) If 'Setting Saved' shows, click [Continue] button. 6) With the same method as above, add Video Server Port. 7) The Web Server Port, Video Server Port and 2 Audio Ports shows in "Virtual Server List" as below. 51 Protocol Select “TCP” in Protocol option. IP Address Input IP Camera IP Address. Enabled Check the square. Appendix - C : Port Forwarding 3. For Netgear RP614 routers: 1) Input http://192.168.0.1 in address bar of web browser. http://192.168.0.1 is the default IP address. 2) If it asks ID and password, input admin as ID and password as password. 3) Click “Port Forwarding” in "Advanced". 4) Click " 1 Add Custom Service" button in Port Forwarding page. 1 5) Input proper values in "Ports - Custom Services" page as below. 5 2 Enable Check it. Service Name Input IP Camera name. Starting/ Ending Port Input IP Camera Web Server port. Starting Port should be same as Ending Port. Server IP Address Input IP Camera IP Address. 6) Click " 2 Add" button. 7) With the same method as above, add Video Server Port. 8) Click "Apply" button to finish Port Forwarding. 52 "QQFOEJY FAQ 1. My POWER light is not on? Power is not being supplied to the unit. Please use the power supply shipped with the unit and verify that a power source is active from the attached power outlet used to connect the adapter. You can test this by plugging in any other electrical device and verify its operation. After using the power supply shipped with the product, checking the power source, and reinserting the power connector into the IP Camera, please call our Support Center. The power supply may be defective. 7. I can’t connect!! In the case of a connection failure. .PEFN3FCPPU.PEFN3FCPPU'JOJTIFE3PVUFS3FCPPU > Router Reboot Finished > IP Camera Reboot > IP Camera Reboot Finish > Verify DDNS and IP Camera connection, if applicable. 8. How do I “PING” an IP address? 0QFOBO.4%04PS$PNNBOE QSPNQU "UUIFQSPNQUUZQFiQJOHYYYYYYYYYYYYwXJUIPVUUIF RVPUFTBOESFQMBDFUIFiYwTXJUIBO*1BEESFTT 2. My ACTIVE light is not flashing? Verify the power supply to the unit. Power off the unit and back on again, wait 1 minute, if the ACTIVE light still does not begin to flash, you will have to set the unit to its factory default (THIS WILL DELETE ANY CONFIGURATION AND SET THE UNIT TO THE FACTORY DEFAULTS). Power on the unit and insert the end of a paper clip into the small recessed opening on the back of the unit. Use the clip to press the button located within that opening. 3) Press Enter 3. My LINK light is not flashing or solid? Verify the cable connection. 99% of the time the cable’s connection to the unit is causing this problem. Try using a different network cable or crossover cable (for PC connection only). Try reinserting the cable, if this still doesn’t solve the problem call our Support Center. 9. I’m accessing my video server remotely over the Internet and the video stream is choppy, is this normal? Yes. The frames per second received remotely are determined by your bandwidth capabilities both at your site where the IP Camera is installed and your remote location. The lower of the two sites will determine how fast your video stream is received. It is recommended to have at least B,CTFDVQTUSFBNDPOOFDUJPOGSPNUIFTJUFXIFSFUIF IP Camera is installed. Lower speeds will operate properly, but provide poor remote performance. The Faster the Internet connection at both ends, the faster the video stream. 4. I can access the video server on my LAN, but not from the Internet. Verify that your router (if applicable) has port forwarding properly configured. If accessing from our DDNS service, verify correct serial number. Firewall issues may prevent user access. 10. How do I enable or check ActiveX on my browser 0QFO*OUFSOFU&YQMPSFS5PPMTPOUIFNFOVCBS*OUFSOFU Options > Security Tab > Custom Level > Scroll down and WFSJGZUIBUZPVBSFQSPNQUFEPSIBWFFOBCMFE"DUJWF9 DPOUSPMTBOEQMVHJOTUPCFEPXOMPBEFEBOEFYFDVUFE DMJDL0,SFTUBSUCSPXTFS 5. How do I open an MS-DOS or Command Prompt? t8JOEPXT.&6TFST 4UBSU1SPHSBNT"DDFTTPSJFT.4%04QSPNQU 11. How do I reset the unit to factory defaults? On the underside of the unit you will find a recessed opening MPDBUFEOFBSUIFUPQMFGUTJEFPGUIFMBCFM1PXFS0/UIFVOJU and use a paper clip to push the reset button within that opening. You should then see the ACTIVE light turn off and after a few seconds the ACTIVE light will begin to flash, signifying a successful reboot. If the ACTIVE light does not turn off after depressing the reset button, please try holding the button in for a few seconds and releasing. YOU WILL LOSE ALL DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE *1$".&3"8*--#&4&550*54'"$503:3&4&54 t8JOEPXT916TFST Start > (All) Programs > Accessories > Command Prompt 6. How do I find out my IP address information if my settings were automatically detected? Windows 98 / ME Users 0QFOBO.4%041SPNQU "UUIFQSPNQUUZQFiXJOJQDGHwXJUIPVUUIFRVPUBUJPONBSLT 6TFUIFESPQEPXOMJTUUPTFMFDUZPVS&UIFSOFU"EBQUFS (not a PPP adapter) /PXZPVXJMMTFFZPVS*1"EESFTT4VCOFU.BTLBOE%FGBVMU Gateway information 5) For DNS information contact your Internet Service Provider Windows 2000 / XP Users 1) Open a Command Prompt "UUIFQSPNQUUZQFiJQDPOGJHBMMwXJUIPVUUIFRVPUFT 3) Near the end of the information supplied, should be your current IP address, subnet mask, default gateway and DNS servers 53 Specifications - Dimension Unit: mm ø120 56.3 44.5 ø120 54 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Adjustable zoom, focus and tilt
- Motion detection
- Alarm input/output
- SD card recording
- DDNS registration