Panasonic_PT-AE2000_User_Manual

Panasonic_PT-AE2000_User_Manual

S

P E C

F

I L E

P r o d u c t N u m b e r :

PT-AE2000

P r o d u c t N a m e :

Full High-Definition Home Cinema Projector

As of September 2007. Appearance and specifications are subject to change without notice.

http://www.pureglare.com.au

< 1 >

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

Specifications

Main Unit

Power supply:

Power consumption:

LCD* 1

Display method:

Drive method:

Pixels:

Lamp* 2 :

Lens:

Screen size:

Throw distance:

Colours:

Brightness* 3 :

Centre-to-corner uniformity ratio* 3 :

Contrast* 3 :

Resolution:

Scanning frequency: RGB:

Optical axis shift* 5 :

Keystone correction range:

Installation:

OSD languages:

Terminals:

YP

B

P

R

(YC

B

C

R

):

S-Video/Video:

HDMI* 6 IN:

COMPUTER IN:

R, G, B:

HD/SYNC, VD:

COMPONENT IN:

Y:

P

B

/C

B

, P

R

/C

R

:

VIDEO IN:

S-VIDEO IN:

SERIAL IN:

PT-AE2000

100 – 240 V AC, 50/60 Hz

240 W (0.08 W in standby mode with fan stopped)

0.74˝ diagonal (16:9 aspect ratio)

Transparent LCD panel (x 3, R/G/B)

Active matrix

2,073,600 (1,920 x 1,080) x 3, total of 6,220,800 pixels

165 W UHM™ lamp

Powered zoom/focus lens (1:1–1:2), F 1.9 – 3.2, f 22.4 – 44.8 mm

40 – 200 inches

1.2–12.0 m (3´11˝– 39´4˝) (16:9 aspect ratio)

Full colour (1,073,741,824 colours)

1,500 lumens* 4

85 %

16,000:1* 4 (full on/full off)

1,920 x 1,080 pixels f

H

30–70 kHz, f

V

50 – 87 Hz,

Dot clock: Less than 150 MHz

480i (525i): f

H

15.75 kHz; f

V

60 Hz,

576i (625i): f

H

15.63 kHz; f

V

50 Hz,

480p (525p): f

H

31.5 kHz; f

V

60 Hz,

576p (625p): f

H

31.25 kHz; f

V

50 Hz,

720/50p (750/50p): f

H

37.5 kHz; f

V

50 Hz,

720/60p (750/60p): f

H

45 kHz; f

V

60 Hz,

1080/50i (1125/50i): f

H

28.125 kHz; f

V

50 Hz,

1080/60i (1125/60i): f

H

33.75 kHz; f

V

60 Hz,

1080/24p (1125/24p): f

H

27 kHz; f

V

24 Hz,

1080/50p (1125/50p): f

H

56.3 kHz; f

V

50 Hz,

1080/60p (1125/60p): f

H

67.5 kHz; f

V

60 Hz f

H

15.75 kHz f

V

60 Hz (NTSC, NTSC4.43, PAL-M, PAL60) f

H

15.63 kHz f

V

50 Hz (PAL, PAL-N, SECAM)

Horizontal: ±40%, vertical: ±100%

Vertical: approx. ±30°

Ceiling/floor, front/rear (menu selection)

English, French, German, Spanish, Italian, Chinese, Korean, Russian,

Swedish, Danish, Norwegian, Polish, Czech, Hungarian, Portuguese,

Thai

HDMI connector x 3

D-sub HD 15-pin (female) x 1

0.7 Vp-p (1.0 Vp-p for Sync on G), 75 ohms

TTL, high impedance (positive/negative polarity)

RCA pin (Y, P

B

/C

B

, P

R

/C

R

) x 2

1.0 p-p, 75 ohms

0.7 Vp-p, 75 ohms

RCA pin x 1, 1.0 Vp-p, 75 ohms

Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

D-sub 9-pin (RS-232C) x 1, for external control

As of September 2007 < 2 >

http://www.pureglare.com.au

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

Power cord length:

Cabinet material:

Dimensions (W x H x D):

Weight:

Operating temperature:

Operating humidity:

PT-AE2000

3 m (9´10˝)

PC + ABS

460 x 130 x 300 mm (18-1/8˝ x 5-1/8˝ x 11-25/32˝) * 7

7.2 kg (15.9 lbs.)

0°–40°C (32°–104°F)

20%–80% (no condensation)

Remote Control Unit

Power supply:

Operation range* 8 :

Dimensions (W x H x D):

Weight:

Supplied Accessories

Optional Accessories

3 V DC (AA type battery x 2)

Approx. 7 m when operated from directly in front of the signal receptor

52 x 200 x 28.5 mm (2˝ x 6-15/16˝ x 7/8˝)

170 g (6 oz.)

Power cord

Wireless remote control unit

Batteries for remote control (AA type x 2)

Replacement lamp: ET-LAE1000

Ceiling mount bracket for high ceilings: ET-PKE2000

Ceiling mount bracket for low ceilings: ET-PKE1000S

Cable cover: ET-PCE2000

Weights and dimensions shown are approximate.

Specifications subject to change without notice.

*1: The projector uses a type of liquid crystal panel that typically consists of millions of pixels. This panel is built with very high-precision technology to provide the finest possible image. Occasionally, a few pixels may remain turned on (bright) or turned off (dark). Please note that this is an intrinsic characteristic of the manufacturing technology that affects all products using LCD technology.

*2: The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to illuminate, due to impact or extended use. The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions.

*3: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

*4: In AI mode, with dynamic iris on.

*5: Shift range is limited during simultaneous horizontal and vertical shifting.

*6: Supports Deep Color and xvYCC color space (effective in Color 1 image mode) of HDMI 1.3a standard.

*7: Lens and legs not included.

*8: Operation range differs depending on environments.

As of September 2007

http://www.pureglare.com.au

< 3 >

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

Dimensions

PT-AE2000

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

460

(18-1/8˝)

315

(12-13/32˝)

Terminals

1 2 3 4 5 6 7 8

9

1 HDMI 1 input

2 HDMI 2 input

3 HDMI 3 input

4 Computer input

5 Component (YP

B

P

R

/YC

B

C

R

) 1 input

6 Component (YP

B

P

R

/YC

B

C

R

) 2 input

7 S-Video input

8 Serial input

9 Video input

COMPUTER IN connector pin assignment

6 11 15

1 5 10

D-sub HD 15-pin, female

3

4

5 no.

1

2 signal

R

G

B

GND

GND

As of September 2007

http://www.pureglare.com.au

8

9

10 no.

6

7 signal

GND

GND

GND

NC

GND

13

14

15 no.

11

12 signal

GND

NC

HD/SYNC

VD

NC

< 4 >

S

P E C

F

I L E

Full High Definition Home Cinema Projector

Standard setting-up positions

Upper edge of projected image

Projected image

L

Lower edge of projected image

181

(7-1/8˝)

*1

70 (2-3/4˝)

L

Projected image

PT-AE2000

unit : mm (inch)

NOTE:

Illustrations show the projector installed using optional ceiling bracket ET-PKE1000S.

This illustration is not drawn to scale.

Values shown are approximate.

Projection distance (screen aspect ratio 16:9)

Projection size (16:9)

Diagonal length

1.01 m / 40˝

1.52 m / 60˝

2.03 m / 80˝

2.54 m / 100˝

3.05 m / 120˝

3.81 m / 150˝

5.08 m / 200˝

Projection distance (L)

Min (Wide) Max (Telephoto)

1.2 m / 3´11˝

1.8 m / 5´10˝

2.4 m / 7´10˝

3.0 m / 10´2˝

3.6 m / 11´10˝

4.5 m / 14´9˝

6.0 m / 19´8˝

2.3 m / 7´7˝

3.5 m / 11´6˝

4.7 m /

6.0 m /

15´5˝

19´8˝

7.2 m / 23´7˝

9.0 m / 29´6˝

12.0 m / 39´4˝

Height from the edge of screen to centre of lens

(E)

-0.25 m – 0.75 m / 9.8˝ – 2´6˝

-0.38 m – 1.13 m / 1´3˝ – 3´8˝

-0.50 m – 1.50 m / 1´8˝ – 4´11˝

-0.63 m – 1.87 m / 2´1˝ – 6´2˝

-0.75 m – 2.25 m / 2´6˝ – 7´5˝

-0.94 m – 2.81 m / 3´1˝ – 9´3˝

-1.25 m – 3.74 m / 4´1˝ – 12´3˝

Width from the right edge of screen to centre of lens

(W)

0.09 m – 0.80 m / 3.5˝ –

0.18 m – 1.60 m /

0.23 m – 2.00 m /

7˝ –

9˝ –

2´7˝

0.14 m – 1.20 m / 5.5˝ – 3´11˝

5´3˝

6´7˝

0.27 m – 2.40 m / 11˝ – 7´10˝

0.34 m – 2.99 m / 1´1˝ – 9´10˝

0.45 m – 3.99 m / 1´6˝ – 13´1˝

Projection distance (screen aspect ratio 4:3)

Projection size (4:3)

Diagonal length

1.01 m / 40˝

1.52 m / 60˝

2.03 m / 80˝

2.54 m / 100˝

3.81 m / 150˝

Projection distance (L)

Min (Wide)

1.5 m / 4´11˝

2.2 m / 7´3˝

3.0 m / 9´10˝

3.7 m / 12´2˝

5.6 m / 18´4˝

Max (Telephoto)

2.9 m / 9´6˝

4.3 m / 14´1˝

5.8 m / 19´

7.3 m / 23´11˝

11.0 m / 36´1˝

Height from the edge of screen to centre of lens

-0.30 m – 0.91 m

-0.45 m – 1.37 m

(E)

/ 11.8˝ –

/

-0.60 m – 1.82 m /

-0.76 m – 2.28 m /

-1.14 m – 3.42 m /

1´6˝ –

4´6˝

2´ –

2´6˝ –

7´6˝

3´9˝ – 11´3˝

Width from the right edge of screen to centre of lens

(W)

0.08 m – 0.73 m /

0.12 m – 1.09 m /

3.1˝ – 2´5˝

4.7˝ – 3´7˝

0.16 m – 1.46 m /

0.20 m – 1.82 m /

6.3˝

7.9˝

0.30 m – 2.74 m / 11.8˝ –

4´9˝

NOTE: The values of L shown above vary due to characteristics of the zoom lens. Images may slightly distort due to characteristics of the zoom lens when the zoom lens is set to the minimum throw distance.

Calculation of the projection distance

For a screen size different from the above, use the equation below to calculate the projection distance.

16 : 9 minimum maximum

L (m) = (diagonal screen size in inches) x 0.0302 - 0.04

L (m) = (diagonal screen size in inches) x 0.0604 - 0.05

4 : 3 minimum maximum

L (m) = (diagonal screen size in inches) x 0.0371 - 0.04

L (m) = (diagonal screen size in inches) x 0.0739 - 0.05

NOTE: The accuracy of calculated value by the formula shown above is ±5%.

As of September 2007 < 5 >

http://www.pureglare.com.au

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Shift range

Optical axis shift function allows to shift the position of a projected image as shown below.

H

(Width of projected image)

0.4H

0.4H

Standard position of projected image

Installable angle

Install the projector at an angle within the range shown below.

• Vertical direction

The projector may be installed at a vertical angle of ±30°.

+30°

-30°

• Horizontal direction

The projector may not be angled horizontally.

As of September 2007

http://www.pureglare.com.au

< 6 >

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Computer data compatibility

This projector accepts up to 70 kHz horizontal scanning frequency and 150 MHz dot clock.

NOTE: The display resolution of this projector is 1920 x 1080 pixels. If the display resolution indicated in the above data does not match this resolution, the input signal will be converted to 1920 x 1080 pixels.

List of Compatible Signals

Display mode

NTSC/NTSC4.43/PAL-M/PAL60

PAL/PAL-N/SECAM

480i (525i)

576i (625i)

480p (525p)

576p (625p)

720 (750)/60p

720 (750)/50p

1080 (1125)/60i

1080 (1125)/50i

1080 (1125)/24p

1080 (1125)/60p

1080 (1125)/50p

VGA480

WIDE480

SVGA

WIDE600

WIDE720

XGA

WIDE768

MXGA

SXGA

WIDE768-2

SXGA60+

WIDE800

WIDE900

Display resolution

(dots)

1

800 x 600

800 x 600

800 x 600

800 x 600

1,072 x 600

1,280 x 720

1,024 x 768

1,024 x 768

1,024 x 768

1,024 x 768

1,024 x 768

1,280 x 768

1,125 x 864

1,125 x 864

1,280 x 1,024

1,360 x 768

1,400 x 1,050

1,280 x 800

1,440 x 900

720 x 480i

720 x 576i

720 x 480i

720 x 576i

720 x 480

720 x 576

1,280 x 720

1,280 x 720

1,920 x 1,080i

1,920 x 1,080i

1,920 x 1,080

1,920 x 1,080

1,920 x 1,080

640 x 480

640 x 480

640 x 480

640 x 480

856 x 480

800 x 600

Scanning frequency

H V

(kHz) (kHz)

Dot clock frequency

(MHz)

Picture quality

2

Format

67.5

56.3

31.5

37.5

43.3

72.1

30.1

35.2

15.7

15.6

15.7

15.6

31.5

31.3

45.0

37.5

33.8

28.1

27.0

60.0

68.7

72.1

45.3

64.0

67.5

64.0

48.8

37.9

48.1

46.9

53.7

37.2

45.1

48.4

56.5

65.1

49.7

55.9

60.0

50.0

59.9

75.0

85.0

138.0

60.1

56.3

59.9

50.0

59.9

50.0

59.9

50.0

60.0

50.0

60.0

50.0

24.0

75.0

85.0

89.0

56.5

71.2

74.9

60.0

59.8

60.3

72.2

75.0

85.1

59.9

60.1

60.0

70.1

59.9

59.8

59.9

148.5

148.5

25.2

31.5

36.0

62.3

31.5

36.0

13.5

13.5

-

-

27.0

27.0

74.3

74.3

74.3

74.3

74.3

78.8

94.5

99.2

76.2

94.2

108.0

108.0

74.3

40.0

50.0

50.0

56.3

51.4

76.5

65.0

75.0

122.4

83.5

106.5

1. The “i” appearing after the resolution indicates an interlaced signal.

2. The following symbols are used to indicate picture quality.

AA

A

Maximum picture quality can be obtained.

Signals are converted by the image processing circuit before picture is projected.

A

A

A

A

A

A

A

A

A

AA

A

A

A

A

A

A

A

A

A

A

A

A

A

AA

AA

A

A

A

A

AA

AA

AA

AA

AA

A

A

A

A

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

PC

VIDEO/S-VIDEO

VIDEO/S-VIDEO

COMPONENT

COMPONENT

COMPONENT/HDMI

COMPONENT/HDMI

COMPONENT/HDMI

COMPONENT/HDMI

COMPONENT/PC/HDMI

COMPONENT/PC/HDMI

COMPONENT/HDMI

PC

PC

PC

PC

COMPONENT/PC/HDMI

COMPONENT/PC/HDMI

PC/HDMI

PC

As of September 2007 < 7 >

http://www.pureglare.com.au

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Serial connector

The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.

Pin assignments and signal names

D-sub 9-pin

3

4

1

2

5

No.

Signal name

TXD

RXD

GND

Description

NC

Send data

Receive data

NC

Ground

8

9

6

7

No.

Signal name

RTS

CTS

Description

NC

Connected internally

Connected internally

NC

Communication conditions (factory setting)

Signal level

Synchronization method

Baud rate

Parity

Character length

Stop bit

X parameter

S parameter

RS-232C-compliant

Start-stop synchronization

9,600 bps

None

8 bits

1 bit

None

None

Basic format

Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control.

STX C1 C2 C3 : P1 P2 P3 P4 ETX

Start

(1 byte) Command

(3 bytes)

Colon

(1 byte)

Parameter

(1-4 bytes)

(Control and/or query commands)

End

(1 byte)

CAUTIION

When sending multiple commands, be sure to send the next command after receiving a response from the projector.

Cable specifications

Projector

1

2

3

4

5

8

9

6

7

NC

NC

DSR

NC

NC

NC

NC

NC

PC (DTE)

1

2

3

4

5

8

9

6

7

As of September 2007 < 8 >

http://www.pureglare.com.au

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Control commands

Command: <Parameter>

Function

Callback: <Parameter> Parameter value

Min Max

P O N

P O F

*

I I S : < i n p u t s i g n a l >

O F Z : < o f f _ o n >

O E N

V P M : < p i c t u r e m o d e >

< N O R >

< D Y N >

< C N 1 >

< C N 2 >

< C N 3 >

< C L 1 >

< C L 2 >

O M N

O C U

O C D

O C L

O C R

O S H

*

O S T

O V M

V S 1

O B K

O L E

*

O O T : < o f f _ t i m e r >

O W M : < x >

Power on (standby mode on)

Power off (standby mode off)

Input signal selection

Freeze

Enter

Picture mode

Normal

Dynamic

Cinema 1

Cinema 2

Cinema 3

Colour 1

Colour 2

Menu

Cursor up

Cursor down

Cursor left

Cursor right

Shutter

The same function as “DEFAULT” button

The same function as “PICTURE MODE” button

The same function as “ASPECT” button

The same function as “RETURN” button

The same function as “LENS” button

Off timer

Waveform monitor activate/off

P O N

P O F

I I S : < i n p u t s i g n a l >

O F Z : < o f f _ o n >

O E N

V P M : < p i c t u r e m o d e >

< N O R >

< D Y N >

< C N 1 >

< C N 2 >

< C N 3 >

< C L 1 >

< C L 2 >

O M N

O C U

O C D

O C L

O C R

O S H

O S T

O V M

V S 1

O B K

O L E

O O T : < o f f _ t i m e r >

O W M : < x >

0

0

0

*

Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.

1

7

8

Status asking commands

Command

Q P W

Q I N

Q P M

Q F Z

Q O T

Q S H

Q W M

Description

Standby power status

Input signal status

Picture mode status Normal

Dynamic

Cinema 1

Cinema 2

Cinema 3

Colour 1

Colour 2

Freeze status

Off timer status

Shutter function status

Waveform monitor status

Callback

<Parameter>

< p o w e r c o n d i t i o n >

< i n p u t s i g n a l >

< N O R >

< D Y N >

< C N 1 >

< C N 2 >

< C N 3 >

< C L 1 >

< C L 2 >

< o f f _ o n >

< o f f _ t i m e r >

< o f f _ o n >

< x >

As of September 2007

http://www.pureglare.com.au

< 9 >

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Parameter format

Parameter format

<off_on>

<input signal>

<power condition>

<off_timer>

<x>

Size (Byte)

1

3

3

1

1

Difinition

0 = off, 1 = on

VID = video, SVD = S-video, RG1 = computer, CP1 = component 1,

CP2 = component 2, HD1 = HDMI 1, HD2 = HDMI 2, HD3 = HDMI 3

000 = power on (standby mode on), 001 = power off (standby mode off)

0 = off, 1 = 60 min, 2 = 90 min, 3 = 120 min, 4 = 150 min, 5 = 180 min,

6 = 210 min, 7 = 240 min

0 = off, 1 = full scan (Y), 2 = full scan (R), 3 = full scan (G), 4 = full scan (B),

5 = single line (Y), 6 = single line (R), 7 = single line (G), 8 = single line (B)

NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.

Command example

To set the volume to +30, send the command as shown below.

STX AVL : 30 ETX

Start Command Parameter End

NOTE: When sending commands without parameters, a colon (:) is not necessary.

As of September 2007

http://www.pureglare.com.au

< 10 >

S

P E C

F

I L E

Full High-Definition Home Cinema Projector

PT-AE2000

Notes on Projector Placement and Operation

The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

1.

Never place objects on top of the projector while it is operating.

2.

Make sure there is an unobstructed space of 100 mm (3-15/16˝) or more around the projector’s air intake openings.

3.

If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings.

100 mm (3-15/16˝) or more

100 mm (3-15/16˝) or more

100 mm (3-15/16˝) or more

Direction of Air Intake and Exhaust

Intake

Exhaust

Operating the Projector Continuously

1. If the projector is to be operated continuously 10 hours or more, lamp replacement cycle duration becomes shorter.

2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

As of September 2007 < 11 >

http://www.pureglare.com.au

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project