te-rvmcir - iBEAM, Vehicle Safety Systems
TE-RVMCIR
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
The TE-RVMCIR is a replacement rearview mirror that has a 4.3” TFT screen built in with dual
video sources, one for reverse viewing with the TE-BPCIR infrared camera, the other for any
video source with a composite video output. The mirror comes with the most widely used
mirror mount to fit many vehicles, or it can use the optional mirror brackets which are sold
separately (Check with your place of purchase for these optional brackets).
IV. Connection
INLINE
FUSE
Rearview Mirror
RED 12+
BLACK GROUND
GREEN TRIGGER
VIDEO 1
MIRROR
II. Specifications
Rearview Monitor Sensor
Screen Size: 4.3”
Display Screen: TFT-LCD
Display Resolution: 480(H)XRGBX272(V)
Aspect Ratio: 16:9
Power Consumption: ≤2W
Power Supply: DC12V
Video Input: AV1 to VCD/DVD (defaulted)
AV2 to backup camera
Signal System: PAL/AUTO/NTSC
Brightness: 250cd/m²
Contrast Ratio: 300:1
Camera Sensor - CMOS II
Effective Pixel: 656 x 492
Horizontal Sync Frequency: 15625KNZ
Vertical Sync Frequency: PAL 50HZ / NTSC
60HZ
Scanning System: 2:1 Interlace
Sync System: Internal
AGC: Auto
BLC: Auto
Resolution: 420 TV Lines
S/N Ratio: More than 48dB
Current Consumption: No more 150mA
Power Supply: DC12V±10%
Operating Temperature: -22° ~ 176° F
Storage Temperature: -40° ~ 176° F
Viewing Angle: 170°
Water-proof: IP67
Minimum Illumination: 0.5Lux / F1.2 (0 Lux
with Led)
III. Installation
Rearview Mirror
1) Remove the existing mirror from the vehicle.
2a) If the OEM mirror has the D style mounting tab on the windshield (most common
mounting tab)
then mount the mirror and continue to step 3.
2b) If the OEM mirror has any other style mount than the D style mounting tab, please contact
your place of purchase about optional mounts.
3) After mirror has been mounted, route wire harness down to connect power, ground and
the backup camera/video source. Be careful when routing the harness so it does not
interfere with any side curtain airbags or gets pinched when reinstalling any interior parts
needed to take off when routing harness. Neatly route it from the mirror to the headliner.
Camera
1)This is a behind license plate camera. Begin by removing the license plate bolts and the
license plate, then install camera. Replace license plate and bolts.
VIDEO 2
1) Connect the RED wire to the +12 volt reverse wire of the vehicle.
2) Connect the BLACK wire to ground (a metal, non-painted surface).
3)Connect the GREEN wire to the reverse trigger wire (RED wire coming from YELLOW
video rca) on camera. (The rearview mirror uses this to sense reverse and transmits a video
signal to the mirror).
Camera
Parking line loop (White)
Reverse Lights
RED (+)
BLACK (Ground)
Red (Reverse Switch)
Reverse Wire on Radio (Trigger)
TV
Video (in)
1) Connect the RED wire to the +12 volt reverse wire of the vehicle.
2) Connect the BLACK wire to ground (a metal, non-painted surface).
3)Run video cable though vehicle, up to video display. (Avoid placing video cable where it
can get pinched or damaged).
4)Attach the YELLOW video rca to the reverse camera input of the radio or video display;
connect the RED wire coming from the YELLOW video rca to the reverse trigger wire on
the radio or video display.
NOTE: The camera comes with the parking assist lines. If you want to remove the parking lines
follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Reconnect power to the camera
If the parking assist lines are wanted just follow the steps above and reconnect the wires.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising