Important Safety Instructions
DRC97983
1.
2. 3. 4. 5. 6. 7. 8. 9. AVC Multimedia
Markham, Ontario L3R 1E3
http://www.RCAav.com
10.
11.
12.
Read these instructions before using your new product for the first time.
Safety Precautions
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to cause an
electric shock.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT PLACE
OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified may
result in hazardous radiation exposure.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR
EQUIVALENT TYPE.
* SEE REAR OF UNIT FOR GRAPHIC SYMBOLS *
CAUTION
INVISIBLE LASER RADIATION
This product
contains a low
power laser device.
WHEN OPEN.
AVOID EXPOSURE TO BEAM.
This Class B digital
apparatus complies
with Canadian ICES003.
On Placement
• Do not use the unit in places that are extremely hot, cold, dusty or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by
placing it on carpeting.
• To avoid magnetized, do not place the unit near speaker or magnet.
• Do not use this unit in direct sunlight or leave the unit in a closed automobile (or yacht, etc) where it would be
exposed to high temperatures above 104°F (40°C).
• No naked flame sources such as lighted candles should be placed on the car power adaptor and main unit.
• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on apparatus.
On Safety
• When connecting or disconnecting the car power adaptor, grip the plug and not the cord itself. Pulling the cord
may damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the car power adaptor.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit.
When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours
before turning the power on, or gradually heat the room and allow the unit to dry before use.
Ventilation Warning
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not operate the unit in a confined space, such as a bookcase or built-in cabinet, allow about 4 inch (10cm) of
free space all around the unit for adequate ventilation.
Rating Plate Location
• The rating plate is located on the rear of unit.
FCC Statements
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
WARNING:
• Should any trouble occur, disconnect the car power adaptor and refer servicing to a qualified technician.
• The AC/DC adaptor is used as disconnect device.
• The AC/DC adaptor of apparatus should not be obstructed OR should be easily accessed during intended used.
• To be completely disconnect the power input, the AC/DC adaptor of apparatus shall be disconnected
from the mains.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited
viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
E-1
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block the ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Remove the PLASTIC
sheet before using the
Remote Control.
BATTERY REPLACEMENT
When the battery becomes weak, the
operating distance of the remote control
will be greatly reduced and you will need
to replace the battery.
TO CHANGE REMOTE BATTERY
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
Notes:
• If the remote control is not going to be used for a long time, remove the battery to avoid damage caused by battery
leakage corrision.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of
these batteries must be strictly followed.
7
8
9
10
11
2
1
12
9) Screen Switch
WIDE: Wide Screen
NORMAL: Pan Screen
10) OFF/ON Switch
11) DC IN 9V-12V Jack
12) Stand
Audio CDs
[8cm/12cm disc]
Compatible
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management Information
that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, it
cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the
symbol appears on the screen, it indicates that the function or operation attempted is not available at that time.
This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain functions may not be available
on some DVDs. Be sure to read the documentation provided with the DVD.
Icons Used on DVDs
Language selections for audio
Sample lcons
Language selections for subtitles
Note:
When playing back a CD-G (Graphics) or CD EXTRA disc, the
audio portion will be played, but the graphic images will not
be shown.
Screen aspect ratio
Multiple camera angles
Region code indicator
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the disc has more than
one movie on it, each movie would be a separate “title”. “Chapters” are
sections of titles.
• Audio CDs are divided into “tracks”. A “track” is usually one song on an
Audio CD.
Title1
Chapter1
Track1
Title2
Chapter2
Track2
Chapter3
Track3
Chapter1
Track4
Chapter2
Track5
Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but some
do not.
Notes on Unauthorized Discs
You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area or
made for business purposes.
Sound System
DVD Player
Dolby Digital
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can reproduce from one
to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-channel listening. An
additional Dolby Digital decoder is required for reproduction of the discrete multi-channel soundtracks available on many
DVDs.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
Accessories
Please check and identify the supplied accessories.
Remote Control (with battery)...........................................................................................................................................................................x 1
Car Power Adaptor.................................................................................................................................................................................................x 1
DC-AV Cable.............................................................................................................................................................................................................x 1
Mounting Strap.......................................................................................................................................................................................................x 2
E-2
1) OPEN Button
Press the
OPEN button and hold the
front panel to unfold it, and press the DVD
door switch on the mid cabinet to open
the disc door.
2) STANDBY Indicator
When the STANDBY / ON switch is slid to
OFF position, the light will illuminate.
3) Headphone Jack
4) VOLUME Control
Adjusts the volume.
5) STANDBY / ON Switch
6) AUDIO & VIDEO OUT Jacks
7) DC IN 9V-12V Jack
8)
SEARCH Button
Performs fast reverse playback.
SEARCH Button
Performs fast forward playback.
PREV Button
Goes back to current or previous chapters/
tracks.
NEXT Button
Advances chapters/titles/tracks.
Button
Flips the screen image.
PAUSE Button
Pauses playback and frame advance.
1. Connect your TV to the DVD player using the
included DC-AV cable.
2. Turn on the TV and follow the instructions included
with it to play the DVD.
Notes:
• Make sure to use the correct DC-AV cable.
Connecting the plugs incorrectly may cause a weak
signal.
• If your TV does not have Audio/Video inputs,
you will need to purchase an RF modulator (sold
separately) and follow the instructions included
with it to connect the unit to your TV.
TV
DO NOT CONNECT
DO NOT CONNECT
DVD player
right side
C. Connecting a Stereo Receiver or Amplifier (for the DVD Player Only)
The DVD player can output stereo and down-mixed
two channel Dolby Digital audio.
Power Supply
The included 12V car power adaptor is designed for use with vehicles that have a 12V, negative ground electrical system.
Using the DVD Player and the Monitor Together
Control Reference Guide
DC-AV cable
(included)
Watching a DVD on Your TV
Listening on External Audio Equipment
WARNING: Do not dispose of the battery in a fire or it may leak and/or explode.
WARNING: Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DVD player
right side
IMPORTANT
This car adaptor is for use with 12 volt batteries only.
Monitor left side
right side
4
VIDEO MODE Button
Adjusts Brigntness, Contrast, Color or View Mode of
the LCD screen.
2)
PREV Button
Moves back through titles, chapters or tracks on a disc.
3)
/
SEARCH Buttons
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
4) GOTO Button
Skips directly to a location on a DVD or CD.
5) Cursor ( , , , ) Buttons
Moves between selections on a menu screen and
adjust certain settings.
ENTER Button
Confirms selections on a menu screen.
6) MEMORY Button
In STOP mode, sets titles/chapters in a favorite order.
7) Number (0 - 9) Buttons
Use when creating programs and locating a title/
chapter or specific time.
8) REPEAT A-B Button
Performs point-to-point repeat playback on a DVD or
CD.
REPEAT DISC Button
Repeats a DVD chapter or title.
Repeats a CD track or the entire disc.
SETUP Button
In stop mode, it brings up the SETUP menu.
9) MENU Button
Enters and exits the main DVD menu.
10)
NEXT Button
Moves forward through titles, chapters or tracks on a
disc.
11) STOP Button
Stops playing a disc.
PLAY Button
Starts or resumes playback of a disc.
PAUSE Button
Pauses playback of a disc.
12) DISPLAY Button
Shows status information on the screen.
If your TV has Audio/Video inputs, you can connect
the DVD player to your TV using the included DC-AV
cable.
4
3
1)
This unit can play
DVDs
[8cm/12cm disc]
• Point the remote control at the REMOTE SENSOR located on the
unit.
• When there is a strong ambient light source, the perform­ance of
the infrared REMOTE SENSOR may be degraded, causing unreliable
operation.
DC OUT 9V-12V Jack
AUDIO & VIDEO IN Jacks
VOLUME Control
Adjusts the volume.
Headphone Jack
LCD Screen
STANDBY Indicator
When the OFF/ON switch
is in OFF position, the light
will illuminate.
7) BRIGHTNESS Control
Adjusts the relative
lightness or darkness of
the screen.
8) COLOR Control
Adjusts the color intensity.
Remote Control
Disc Formats
Using the Remote Control
1) 2)
3)
4)
5)
6) B. Connecting a TV (for the DVD Player Only)
6
To cigarette
lighter socket
DC-AV cable
(included)
Car Power
Adaptor
DVD player
right side
1. Connect the DVD player to the left/right Audio In
jacks on the other equipment using the included
DC-AV cable.
2. Turn on your audio equipment and follow the
instructions provided with it to select the AUDIO IN
function.
DC-AV cable
(included)
Notes:
• Make sure to use the correct DC-AV cable. Connecting
the plugs incorrectly may cause a weak signal.
• If you have a stereo VCR, make sure you set it to
stereo mode.
• Due to copyright protection, DVD movies cannot be
copied. If you copy a DVD movie onto a videotape, the
resulting copy will be unclear, with poor sound quality.
This is NOT caused by a defective DVD system.
DO NOT CONNECT
DO NOT CONNECT
8" Dual Screen Mobile DVD System
5
Monitor
DO NOT CONNECT
D. Connecting Game Systems/Video Equipment (for the Monitor Only)
Monitor left side
You can connect game systems or other video equipment for playback using the monitor.
1
To A/V OUT &
DC IN 9V-12V
jacks
3
To A/V IN &
DC OUT 9V-12V
jacks
2
Watching Video Equipment
To DC IN 9V-12V
jack
1. Connect the other equipment to the monitor using a standard AV Cable (not included).
2. Turn on the monitor.
3. Turn on the video equipment and follow the instructions provided with it to playback.
Using the DVD Player or the Monitor Separately
WARNING:
Disconnect this car power adaptor when
not in use. Not for use in 24V vehicles.
Monitor
right side
DVD player
right side
Car Power Adaptor
Car Power Adaptor
13) ANGLE Button
Switches between multiple camera angles when
the DVD you are playing has been programmed
with multiple camera angles.
14) AUDIO Button
Selects one of the audio sound tracks on a DVD
(if more than one is available) or select the audio
output mode on an CD.
15) SUBTITLE Button
Selects one of the subtitle languages programmed
on a DVD (if available).
RETURN Button
Returns to normal operation after using the SETUP
menu of a DVD.
1
2
3
4
5
10
9
PLAY Button
Starts or resumes playback of a disc.
STOP Button
Stops playing a disc.
9) LCD Screen
10) Remote Sensor
Receives the remote control signal.
E-3
See more at http://www.manualsworld.net
8
To cigarette
lighter socket
E. Using the Monitor with Other Equipment while Playing DVD on the DVD Player
You can use a game console or other video equipment on the monitor while viewing a DVD on the DVD player.
To DC IN 9V-12V
jack
To DC IN 9V-12V
jack
•
AV cable
(not included)
To A/V IN jacks
To cigarette
lighter socket
•
•
Game System /
Video Equipment
2
2
• •
•
Notes:
• Make sure to use the correct Audio/
Video cable. Connecting the plugs
incorrectly may cause a weak signal.
• If you have a mono VCR, the volume
level from the speakers will be low.
1
1
Connections
6
You can watch the same DVD on the DVD player and
the monitor.
7
Watching a DVD on the DVD Player and the
Monitor
Monitor left side right side
DVD player
right side
Cautions:
• Use this unit only with the included 12V car power adaptor. Use with other car adaptors could damage the unit,
or even your vehicle.
The included 12V car power adaptor is for use with this unit only. Do not use it with any other equipment.
In the interest of traffic safety, drivers should not operate the unit or view videos while driving.
When the inside of the 12V power outlet is dirty with ashes or dust, the plug section may become hot due to poor
contact. Be sure to clean the 12V power outlet before use.
After use, disconnect the 12V car power adaptor from both the unit and 12V power outlet.
If the unit is not properly attached to a vehicle, it may become airborne in the event of an accident and cause damage,
injury, or death.
Check your local traffic laws for rules governing the use of video devices in vehicles.
A. Watching a DVD on the DVD Player and
the Monitor
Game System /
Video Equipment
DVD player
right side
Monitor left side
AV cable
(not included)
To
cigarette
lighter
socket
To A/V OUT &
DC IN 9V-12V jacks
DC-AV cable
(included)
DO NOT CONNECT
User Manual
Remote Control
DO NOT CONNECT
Important Safety Instructions
To DC IN
9V-12V
jack
To A/V IN &
DC OUT 9V-12V
jacks
Watching Video Equipment on the Monitor while Viewing a DVD on the DVD Player
1. Connect the DVD player and the monitor using the
included DC-AV Cable.
2. Turn on the DVD player and the monitor.
3. Play a DVD on the DVD player; the monitor will play
the same DVD at the same time.
DC-AV cable
(included)
To A/V OUT &
DC IN 9V-12V
jacks
E-4
To A/V IN &
DC OUT 9V-12V
jacks
1. Connect the power connector between the DVD player and the monitor. Do not connect the Audio/Video portion of the
DC-AV cable.
2. Connect the monitor to the other equipment using a standard AV cable (not included).
3. Turn on the DVD player, the monitor and the other equipment.
4. Play a DVD on the DVD player.
5. Use the monitor for the other equipment.
Notes:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.
• If you have a mono VCR, the volume level from the speakers will be low.
E-5
F. Using Headphones/Earphones
Repeat Playback
Playing a Disc
Headphones / Earphones
[1/8” (3.5mm) diameter plug]
Turn down the volume before connecting the
headphones/earphones. Slowly raise the volume
with the headphones on until you reach your desired
volume. When headphones are connected, the speaker
is automatically disabled.
This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a manner
that allows specific or limited operation during playback. Therefore, this unit may not respond to all operating
commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the specific DVD in question for
more information about the options available on that DVD.
“ ” may appear on the screen during operation. A “ ” means that the desired operation is not permitted by the
unit or disc.
Warning:
Playing a Disc
Excessive sound pressure from earphones and
headphones can cause hearing loss. Avoid listening to
sound at excessive levels which could be harmful to
your ears.
DVD player
right side
Monitor
left side
1. Slide the STANDBY / ON switch on the top of the unit to the ON position. (Slide the ON/OFF switch on the monitor to the
ON position.) See Customizing the Function Settings before proceeding to step 2.
2. Press the OPEN button and hold the front panel to unfold it, and press the DVD door switch on the mid cabinet to open
the disc door.
Press here to open
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a Chapter
1. While the DVD is playing, press the REPEAT DISC button until the “
current chapter is played repeatedly.
” indicator displays on the screen. The
Repeating a Title
2. While the DVD is playing, press the REPEAT DISC button until the “
current title is played repeatedly.
” indicator displays on the screen. The
To Resume Normal Playback
3. While the DVD is playing, press the REPEAT DISC button until the “
” indicator displays on the screen.
Repeating a Single Track
” indicator displays on the screen.
Repeating a Whole Disc
2. While the CD disc is playing, press the REPEAT DISC button until the “
whole disc is played repeatedly.
Mounting in the Vehicle
Use the supplied mounting straps to install the DVD player and monitor on the back of the vehicle's headrests. Tightly wrap
the mounting strap around the headrest.
Mounting the DVD Player
3. Hold the disc by its edge and gently push it onto the spindle, with the label side facing toward you, until you hear a “click”.
4. Push the disc door gently to close it. It takes a short while for your unit to load the disc. After loading, for most DVDs, the
unit will automatically take you main menu or start playing. If the unit does not automatically start playing the DVD, press
the  PLAY button.
Pausing Playback (Still Mode)
Press the PAUSE button. To resume normal playback, press the PLAY button.
Each time you press the PAUSE button, the picture advances one frame on a DVD.
Press the STOP button at the location where you want to interrupt playback. To resume playback at the position where the
disc was stopped, press the PLAY button.
PLAY button will reset the disc to
If you press the STOP button twice, the unit’s memory will be cleared and pressing the
the beginning.
Fast Forward / Fast Reverse
or
Mounting the Monitor
2. Press the PLAY button when you reach the desired point to resume normal playback.
Notes:
• The DVD player mutes sound and subtitles during reverse and forward scan of DVDs.
• The fast playback speed may differ depending on the disc.
Skip (Forward / Reverse)
• Press the
NEXT button to advance titles/chapters/tracks.
PREV button to go back to current or previous titles/chapters/tracks.
• Press the
• For Audio CDs, use the number buttons on the remote control to jump directly to the desired track.
Audio Selection
On some DVDs, the sound is recorded in two or more formats.
1. While a disc is playing, press the AUDIO button to show the current audio format
number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Notes:
• If only one audio format is recorded on the DVD, the number does not change.
• Some DVDs allow you to change audio selections using the disc menu only. If this is the case, press the MENU button and
choose the appropriate language on the disc menu.
• You can select different audio channels (Stereo, Left or Right) on an Audio CD by pressing the AUDIO button repeatedly.
Installation Guide
Subtitle Selection
DVD
1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown
in the example.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles
” is displayed.
off by pressing the SUBTITLE button repeatedly until the “
Notes:
• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the subtitle function to off.
• During some scenes, the subtitles may not appear immediately after you select your desired scene.
• The number of subtitle languages recorded differs depending on the disc. If only one language is recorded, the language
does not change.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• Some DVDs allow you to change subtitles using the disc menu only. If this is the case, press the MENU button and choose
the appropriate subtitle on the disc menu.
Angle Selection
DVD
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same scene can be
viewed from each of these different angles.
SAFETY WARNING !
• This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.
• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not obstruct any safety device, including air bags or seat belts.
• All passengers should wear seat belts when using this unit in a moving vehicle.
• If in doubt, please contact your vehicle manufacturer for further advice.
1. While you are playing a DVD with different angles recorded, press the ANGLE
button to view the number of current angles available.
2. Press the ANGLE button repeatedly to change the scene to the next recorded
angle.
• After approx. two seconds, playback will continue from the new angle you
selected.
• If no button is pressed within 10 seconds, playback continues without
changing the current angle.
Using the Stand for Desktop Use
Notes:
• This function can only be used for discs on which scenes shot from multiple angles have been recorded.
” is displayed.
• If only one angle is recorded, “
Unit Operation
You can stand the DVD player and monitor up on a desk or
table following the instructions described as below:
For DVD player: Press the
OPEN button on the top of
the unit, then unfold the screen and place the unit on a flat
surface.
For monitor: Flips the stand on the back of the monitor
shown as the following illustration.
Turning on the Unit
1. Slide the STANDBY / ON switch on the DVD player to the
ON position. Slide the ON / OFF switch on the monitor
to the ON position.
2. The start-up picture will appear on the screens.
Monitor
3. After use, slide the STANDBY / ON switch on the DVD
player to STANDBY (power off ). Slide the ON / OFF
switch on the monitor to the OFF position.
Display Function
DVD
While the disc is playing, press the DISPLAY button repeatedly to display
information on operation status.
Elapsed Time: Elapsed time from the beginning of the title
which is currently playing.
Remain Time: Remaining time of the title which is currently
playing.
Adjust the LCD Screen
You can adjust Brightness, Contrast, Color or View Mode of the LCD screen.
1. Press the VIDEO MODE button.
2. Press the or button to select Brightness, Contrast, Color or View Mode.
3. Press the or button to change the setting. (For View Mode, press the ENTER button to change the setting).
4. Press the VIDEO MODE button to exit the menu.
Note: For the monitor, you can adjust the LCD screen by the BRIGHTNESS control, COLOR control and Screen (16:9 / 4:3) switch
on the monitor.
E-6
E-7
Repeating a Specific Section
” indicator displays on the screen.
DVD
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“
” is displayed) you want
to play repeatedly.
” is displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section (“
3. The unit will immediately begin replaying your selection.
To Resume Normal Playback
Stopping Playback
or
SEARCH button when a disc is playing. Each time you press the SEARCH
1. Press the SEARCH
SEARCH button, the playback speed changes in the following sequence:
” indicator displays on the screen. The
To Resume Normal Playback
3. Press the REPEAT DISC button until the “
4. While the disc is playing, press the REPEAT A-B button until the “
” indicator displays on the screen.
Notes:
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that includes multiple camera angles.
• You can specify a segment only within the current title or track.
• There may be a slight difference between point A and the location where playback actually resumes depending on the disc.
Locating a Desired Section
Locating a Specific Title
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. Press the GOTO button.
Title
2. Press the corresponding number button(s) for the title you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
---
Locating a Specific Chapter
If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that number.
1. Press the GOTO button.
Chapter
--or
button to display Chapter and press the corresponding number
2. Press the
button(s) for the chapter you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Locating a Specific Time
Troubleshooting Guide
SYMPTOM
Language
DVD
1. While the CD disc is playing, press the REPEAT DISC button until the “
The current track is played repeatedly.
Installing in a Vehicle
DVD Player
Customizing the Function Settings
DVD
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button.
Time
--:--:-2. Press the or button to display Time and press the corresponding number buttons
for the setting point you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Notes:
• If the numbers you entered is not permitted by the DVD, after you press the ENTER button, it will restore to - - : - - : - -. You
should re-enter correct numbers.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
DVD Programmable Memory
You can combine your favorite titles/chapters and play them in the order you determine.
1. In stop mode, press the MEMORY button, the following display appears.
2. Select the items in the order you want by pressing the number buttons.Each time you
press the Cursor buttons ( , , , ), the space is highlighted. Highlight where you
want to enter, then press the corresponding number buttons.
3. Press the Cursor buttons ( , , , ) to move the highlighted bar to Play Memory, then
Title
Chapter
press the ENTER button. The DVD player starts memory playback.
4. To resume normal playback from memory playback
a) Press the MEMORY button in stop mode.
b) Press the Cursor buttons ( , , , ) to move the highlighted bar to “Clear All”, then press the ENTER button. All the
input programs will be cleared.
c) Press the PLAY button to resume normal playback.
Notes:
• If the title or chapter numbers you entered is not permitted by the DVD, after you press the ENTER button, it will restore to - - -.
You should re-enter correct numbers.
• Some discs may not permit memory playback operation.
• If you select repeat during memory playback, the DVD player repeats the current memory playback.
• If you press the MEMORY button while the display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you open the disc tray or turn off the DVD player.
Viewing JPG Files
No power.
OSD (On Screen Display) Language
1. Press the SETUP button in stop mode.
2. Press the button to select OSD Language.
3. Press the ENTER button, then the or button to shift and change the
Language.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Subtitle
1. Press the SETUP button in stop mode.
2. Press the button, then the or button to select Subtitle.
3. Press the ENTER button, then the or button to shift and change the Language.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Notes:
• Some DVDs may be set to display subtitles in a different language other than the ones you selected. A prior subtitle language
may be programmed on the disc.
• Some DVDs allow you to change subtitle selections using the disc menu only. If this is the case, press the MENU button and
choose the appropriate subtitle language from the selection on the disc menu.
Audio
Follow the steps mentioned in the “Subtitle“ section to set up the desired audio language.
Note: Some DVDs may not be played in the language you selected. A prior language may be programmed on the disc.
DVD Menu
Follow the steps mentioned in the “Subtitle“ section to set up the desired DVD menu language.
Note: Some DVDs may not include your pre-selected language. In this case, the DVD player automatically displays disc menus
consistent with the disc’s initial language setting.
Video
Aspect Ratio
1. Press the SETUP button in stop mode.
2. Press the or button to select Video.
3. Press the button, then the or button to select Aspect Ratio.
4. Press the ENTER button, then the or button to shift and change the aspect
ratio.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
View Mode
1. Press the SETUP button in stop mode.
2. Press the or button to select Video.
3. Press the button, then the or button to select View Mode.
4. Press the ENTER button, then the or button to shift and change the View Mode.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
Fill:
Fill the screen with decoded image.
Original:Display image as its original size.
Auto Fit: Automatically fit the decoded image on screen without distortion.
Black bars will be present on top/bottom or left/right of screen.
Pan Scan:Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Sides of the picture are cut off.
Note: Depending on the DVD, you may not be able to view the mode as selected.
Misc
Use Default Settings
1. Press the SETUP button in stop mode.
2. Press the or button to select Misc.
or
button to select “Use Default
3. Press the button, then press the
Settings” dialogue box.
4. Press the ENTER button, then press the or button to select “Yes”. Press the
ENTER button and the original setting will be restored. The unit will exit the
default setting menu automatically and re-load the disc in the disc tray.
Note: It will take 3-5 seconds to reset the DVD player to the factory default.
Screen Saver
1. Press the SETUP button in stop mode.
2. Press the or button to select Misc.
3. Press the button, then press the or button to select Screen Saver.
4. Press the ENTER button, then press the or button to change the On/Off
mode.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
1. Open the disc door.
2. Hold a JPG file disc by its edge and gently push it onto the spindle with the
label side facing toward you until you hear a “click”.
3. Close the disc door. A list of folders/files will appear on the screen.
4. Press the or button to select your desired file. The selected picture will
appear at the lower right corner. Press the PLAY button to start playback.
Press the STOP button to display a folder list.
Notes:
• You can press the PAUSE button to freeze the picture. Press the PLAY
button to resume picture slide show.
• You can press the STOP button to quit playback.
PREV or
NEXT button to change the picture.
• You can press the
• You can press the ANGLE button on the remote control to rotate direction of the picture by 90°.
• Some discs may not permit this operation.
E-8
See more at http://www.manualsworld.net
Make sure the infrared remote sensor is not blocked.
Make sure the plastic sheet has been removed from the remote control.
Point the remote directly at the infrared remote sensor on the unit.
Replace the battery in the remote control with a new one.
Use remote control near the unit.
No sound or only a very • low-level sound is heard. •
•
•
•
•
•
Make sure ON mode was selected.
Make sure the system is not paused. Press the PLAY button.
The unit is in fast-forward or fast-reverse mode. Press the PLAY button.
Make sure the AUDIO/VIDEO output and input connections are correct.
The DTS DVD cannot be decoded to have speaker output.
The unit is too hot; shut off the unit for 30 minutes to cool it down.
The volume control is located on the side of the unit – please try adjusting this.
No picture
• The region number of the disc doesn't match the region number of this unit.
The picture is not clear.
• The DVD is dirty. Gently clean the disc.
• The disc is scratched.
• Adjust the LCD's brightness, contrast and color using the VIDEO MODE button on the remote
control.
Severe hum or noise is
heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
• Clean the disc.
The disc does not play.
•
•
•
•
•
The picture is up-sidedown.
• Press the
There is no disc inside (“No Disc” appears on the screen).
Insert the disc correctly with the playback side facing towards you.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait
about an hour for it to clear and try again.
button located on the front of the DVD player.
Specifications and external appearance are subject to change without notice.
LIMITED WARRANTY
AVC MULTIMEDIA (“AVC”) makes the following limited warranty. This limited warranty extends to the original consumer purchaser and is
limited to non-commercial use of the product.
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of one year from
the date of their original retail purchase. If the unit fails to conform to this warranty, we will service the product using new or refurbished parts
and products, at AVC’s sole discretion.
During a period of one year from the effective warranty date, AVC will provide, when needed, service labor to repair a manufacturing defect
at its designated Service Center. To obtain warranty service in the United States, you must first call our Customer Support Center at 1-800506-5746 or 1-877-252-6873, during the hours listed in the box below. The determination of service will be made by AVC Customer
Support. PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION. New or remanufactured replacements for
defective parts or products will be used for repairs by AVC at its designated Service Center for one year from the effective warranty date. Such
replacement parts or products are warranted for an additional one year from the date of repair or replacement. The Customer will be required
to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs. The customer is
responsible for all transportation charges to the service facility.
Packaging and Shipping Instruction
When you send the product to the AVC service facility you must use the original carton box and packing material or an equivalent as
designated by AVC.
LIMITED WARRANTY
Your Responsibility
(1) You must retain the original sale receipt to provide proof of purchase.
(2) These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3) Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which have been lost or
discarded, or damage to product or parts caused by misuse, accident, improper operation or maintenance, or use in violation of
instructions provided with the product, or to product which has been altered or modified without authorization of AVC, or to products or
parts thereof which have had the serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has expired, please contact our Customer Support Center at
1-800-506-5746, 1-877-252-6873 or www.RCAav.com
Hours: Monday–Thursday: 9am–7pm, Friday: 9am–5pm, Saturday: 9am–NOON Eastern time.
Important: You are responsible for any transportation, shipping or insurance relative to the return of product to our Product Returns
Center.
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly
limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited,
the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller
with respect to the repair or replacement of any parts. In no event shall AVC be liable for consequential or incidental damages.
Maintenance
Cleaning the Disc
This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommendable).
• Ensure the car power adapter is connected.
• Make sure that the unit is turned on.
The remote control does • •
not function.
•
•
•
Aspect Ratio
Notes:
• The displayable picture size is preset on the DVD. Therefore, the playback picture of some DVDs may not conform to the
picture size you select.
• When you play DVDs recorded in the 4:3 picture size only, the playback picture always appears in the 4:3 picture size
regardless of the Aspect Ratio setting.
• Select 16:9 to conform to the LCD screen on the unit. Always be sure that your Aspect Ratio conforms to the actual TV in use
if you connect the unit to a TV.
CAUSE (AND REMEDY)
A defective or soiled disc inserted into the unit can cause sound to drop out during playback. Handle the disc by holding its
inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the Unit
• Be sure to turn the unit off and disconnect the car power adapter before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a
weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.
Important Note
• Before transporting the unit, remove any disc from the disc compartment.
E-9
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner
whatsoever. The time within action must be commenced to enforce any obligation of AVC arising under the warranty or under any statute, or
law of the United States or any state thereof, is hereby limited to one year from the date of purchase. This limitation does not apply to implied
warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary, from state to state. Some states do not allow
limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential
damages, so the above provisions may not apply to you.
For more information on other products and services, please visit our web site at
www.RCAav.com
Important: Also keep your “Bill of Sale” as proof of purchase.
Model no........................................................................................................................ Product name..................................................................................................................
Type of set....................................................................................................................................................................................................................................................................
Serial no.......................................................................................................................... Invoice no.........................................................................................................................
Date purchased............................................................................................................ Dealer name....................................................................................................................
FOR SERVICE AND REPAIR, PLEASE VISIT www.RCAav.com
Printed in China
811-798391W011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement