GANZ ZN-D100VE IP camera Quick User Guide

Below you will find brief information for IP camera ZN-D100VE. This document guides you through the initial setup process for the ZN-D100VE IP camera. It covers the installation of the device, connecting cables, setting up the network environment, viewing video on a web page, and configuring the IP address. It's a helpful resource for new users to get started with their camera.

PDF Download

Document

ZN-D100VE

Quick User Guide

This manual has been designed to guide you through basic settings of your IP devices, such as installation and configuration for using them.

Step1. . Assemble and install IP device

Manual adjustment for 3‐axis movements

After installation, make a manual adjustment on the inner liner. Perform 3‐axis movements manually by turning the inner liner to different directions as above, and check if it moves properly. After adjustment, fasten the screw of the rotation axis.

Lens Focus Adjustment

1) Open the dome cover from the device.

2) Uncover the latch(C) carefully to remove the lens cover.

3) Rotate the lens focus ring(D) to adjust the focus and fasten the screw(E) using the included hex wrench.

4) Push the lens cover to the module until the latch(C) clicks into position.

5) Attach the dome cover by aligning protrusion on the body (B) with the inverted triangle mark of the dome cover (A). Turn the dome cover clockwise to lock.

2010/2‐1

* Models herein and their appearance are subject to change without any prior notice.

Installation

1) Connect the LAN cable and power supply cable with the camera. For the detailed information, please refer to

the Step2.

2) Place the installation template

(which is included in the package) on

the ceiling.

3) Drill two holes on the template and insert anchor blocks into the holes.

Fasten the camera with screws.

4) Put the dome cover on the main body of the camera. Make sure the main body and the cover fit each other

into place.

Caution

When assembling the main body of the camera and its dome cover, make sure they fit

each other into place.

The camera may fall off the ceiling even after the proper installation and mounting. To prevent any accident, make sure the ceiling is firm and stable enough to support the camera . If any reinforcement is needed, consult with your safety personnel and proceed with the installation.

2010/2‐1

Step2. Connect cables to IP device

Connect each cable to the device. To see the correct positions of all connectors, refer to the following image below.

LAN

DC 12V

Caution

Make sure the polarity is correct. Incorrect connection may cause malfunction or damage to the IP device.

Step3. Set up network environment

* Models herein and their appearance are subject to change without any prior notice.

Power Adaptor Connector (DC 12V)

The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the

MAC address of your device. Please make sure the device and your PC are on the same network segment before running the installation. If the network segment was different between your PC and the device, change your PC’s settings as below.

IP address : 192.168.xxx.xxx

Subnet mask: 255.255.0.0

2010/2‐1

STEP4. View video on web page

View the live video on a web page using your IP device and its IP address. To have the correct IP address ready and use it on a web page:

1. Convert a MAC address to an IP address.

(The MAC address is attached on the side or bottom of the device.)

MAC address = 00‐1C‐B8‐C0‐14‐B1 → IP address = 192.168.20.177

the Hexadecimal number to Decimal number.

2. Open a web browser and enter the IP address of the device.

3. Click Continue to this website (not recommended) as below.

(The explanation and captured images at this manual are mainly on the basis of Internet Explorer 7.0)

4. Click pop‐up blocked and install the ActiveX control as below. You need to install the ActiveX for displaying the images.

2010/2‐1

5. Wait for a few seconds while the web page loads. The live video is displayed as below.

6. If the live video is not displayed and “Can not Create XMLDOMDocument Install MSXML4.0” message is shown as below, please download and Install from the link below. http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B‐B4F2‐46DA‐B4B6‐

C5D7485F2B42&displaylang=en

(VCA Library requires MS XML 4.0 library which is an xml parser made by Microsoft.)

2010/2‐1

Step5. Setting IP Address

To set up the Network configuration:

1. Click Setup on the upper right of the web page. The login page is displayed as below.

2. Enter the default user name (root) and the default password (pass), and then select OK.

The default username and password are: root and pass .

3. Click System Options, and then select TCP/IP from the drop‐down menu.

To change the IP address, please make sure to check and have the correct Subnet mask and Gateway ready. To

use DHCP, select Obtain an IP address via DHCP.

To learn how to set up the web page for advanced configuration, refer to the Web Page User's Manual, which is available on the SDK at the following path.

{SDK root}\DOC\

2010/2‐1

Advanced setup (ZNS-GIT IPAdminTool)

ZNS‐GIT IPAdminTool is a utility program for IP products. Following list shows a part of features that ZNS‐GIT

IPAdminTool provides. z Configure IP address, Subnet mask and Gateway z Shows network related information such as MAC address z Updates firmware z Reboots the device

ZNS‐GIT IPAdminTool is provided with SDK at the following SDK path.

{SDK root}\BIN\TOOLS\AdminTool\

More Information

To learn more about using other features of your devices, refer to the manual, which is available on the SDK at the following path.

{SDK root}\DOC\

2010/2‐1

Hello! I am an AI chatbot specifically trained to assist you with the ZN-D100VE IP camera Quick User Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Hide related prompts

Assistant typing

Assistant terminated

Key Features

3-axis movement manual adjustment
Lens focus adjustment
Installation
Network Configuration
Web Interface for Live Video
IP Address Config
Advanced Setup with IPAdminTool
Firmware Update
Reboot Device

Frequently Answers and Questions

What is the default IP address for the ZN-D100VE camera?

The default IP address is 192.168.XXX.XXX. You can find the specific IP address using the MAC address of the device.

How do I connect the ZN-D100VE camera to my network?

Connect the LAN cable and power supply cable to the camera. Make sure the polarity of the power supply connector is correct. Refer to the image in the manual for correct connector positions.

How do I adjust the focus of the lens?

Open the dome cover, remove the lens cover, rotate the lens focus ring to adjust focus, fasten the screw with an included hex wrench, and reattach the covers.

What if the live video is not displayed and shows an error message about installing MSXML4.0?

Download and install MSXML4.0 from the link provided in the manual. This library is required for the VCA Library to properly display images.

How do I change the IP address of the camera?

Access the camera's web interface, go to System Options > TCP/IP. Enter the desired IP address, Subnet mask, and Gateway. To use DHCP, select Obtain an IP address via DHCP.

What is ZNS-GIT IPAdminTool?

This is a utility program for IP products that provides features like configuring IP address, subnet mask, gateway, showing network information, updating firmware, and rebooting the device.