Material Safety Data Sheet

Material Safety Data Sheet
MATERIAL SAFETY DATA SHEET MINE AND PORTABLE CABLE REPAIR KIT 8096-4
02/05/2009
Material Safety Data Sheet
Copyright, 2009, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
PRODUCT NAME: MINE AND PORTABLE CABLE REPAIR KIT 8096-4
MANUFACTURER: 3M
DIVISION: Electrical Markets Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 02/05/2009
Supercedes Date: 08/09/2001
Document Group: 10-5603-5
ID Number(s):
80-6100-7684-8
This product is a kit or a multipart product which consists of multiple, independently packaged components. An MSDS for
each of these components is included. Please do not separate the component MSDSs from this cover page. The document
numbers of the MSDSs for components of this product are:
11-4627-3, 06-9230-1, 06-9232-7
No revision information is available.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
_________________________________________________________________________________________________________
Page 1 of 2
MATERIAL SAFETY DATA SHEET MINE AND PORTABLE CABLE REPAIR KIT 8096-4
02/05/2009
_________________________________________________________________________________________________________
Page 2 of 2
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: SCOTCHCAST RESIN 2130 (PART A)
MANUFACTURER: 3M
DIVISION: Electrical Markets Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 12/17/2008
Supercedes Date: 09/29/1999
Document Group: 06-9230-1
Product Use:
Intended Use:
Specific Use:
Electrical
Part A of two part electrical resin
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
POLYETHER-HYDROCARBON-URETHANE POLYMER
154517-54-1
% by Wt
100
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Light straw colored liquid with pungent odor.
General Physical Form: Liquid
Immediate health, physical, and environmental hazards:
Hazardous polymerization may occur.
reaction.
May cause allergic respiratory reaction.
May cause target organ effects.
May cause allergic skin
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
_________________________________________________________________________________________________
Page 1 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Inhalation:
May be harmful or fatal if inhaled.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Allergic Respiratory Reaction: Signs/symptoms may include difficulty breathing, wheezing, cough, and tightness of chest.
Prolonged or repeated exposure may cause:
Respiratory Effects: Signs/symptoms may include cough, shortness of breath, chest tightness, wheezing, increased heart rate,
bluish colored skin (cyanosis), sputum production, changes in lung function tests, and/or respiratory failure.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
If signs/symptoms develop, get medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
_________________________________________________________________________________________________
Page 2 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
OSHA Flammability Classification:
No Data Available
>=300 ºF [Test Method: Closed Cup]
No Data Available
No Data Available
Class IIIB Combustible Liquid
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures:
(SCBA).
Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
Unusual Fire and Explosion Hazards:
Not applicable. No unusual fire or explosion hazards are anticipated.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical
ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition
source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. Pour isocyanate decontaminant
solution (90% water, 8% concentrated ammonia, 2% detergent) on spill and allow to react for 10 minutes. Or pour water on spill and
allow to react for more than 30 minutes. Cover with absorbent material. Place in a container approved for transportation by
appropriate authorities, but do not seal the container for 48 hours to avoid pressure build-up. Working from around the edges of the
spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent
until it appears dry. Collect as much of the spilled material as possible. Clean up residue with an appropriate solvent selected by a
qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS.
Collect the resulting residue containing solution. Place in a closed container approved for transportation by appropriate authorities.
Cover, but do not seal for 48 hours. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid eye contact. Avoid skin contact. Avoid breathing of vapors, mists or spray. Use general dilution ventilation and/or local
exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use
respiratory protection equipment. Do not ingest. Avoid contact with water. For industrial or professional use only.
7.2 STORAGE
Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container tightly closed. Store in a
cool, dry place.
_________________________________________________________________________________________________
Page 3 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. If exhaust ventilation is not available, use appropriate respiratory protection. Do not
use in a confined area or areas with little or no air movement.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact.
The following eye protection(s) are recommended: Full Face Shield, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber, Nitrile Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M Respiratory Selection
Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
None Established
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Light straw colored liquid with pungent odor.
Liquid
No Data Available
>=300 ºF [Test Method: Closed Cup]
No Data Available
No Data Available
>=300 ºF
Vapor Density
No Data Available
Vapor Pressure
No Data Available
Specific Gravity
pH
Melting point
1.08 [Ref Std: WATER=1]
Not Applicable
Not Applicable
_________________________________________________________________________________________________
Page 4 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
Solubility in Water
Evaporation rate
Volatile Organic Compounds
Percent volatile
VOC Less H2O & Exempt Solvents
Viscosity
12/17/2008
Nil
No Data Available
No Data Available
Nil
No Data Available
700 - 900 centipoise
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong bases; Alcohols; Water
Hazardous Polymerization: Hazardous polymerization may occur.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
Carbon dioxide
Hydrogen Cyanide
Oxides of Nitrogen
During Combustion
During Combustion
During Combustion
During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility in the presence of a combustible material. As a disposal
alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
_________________________________________________________________________________________________
Page 5 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
LH-A100-0638-1, LH-A100-0638-2, LH-A100-0638-3, LH-A100-0638-4, 80-6107-3192-1
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
_________________________________________________________________________________________________
Page 6 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART A)
12/17/2008
NFPA Hazard Classification
Health: 3 Flammability: 1
Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 1
Reactivity: 0
Protection: X - See PPE section.
Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and
Coatings Association (NPCA).
No revision information is available.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 7 of 7
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: SCOTCHCAST RESIN 2130 (PART B)
MANUFACTURER: 3M
DIVISION: Electrical Markets Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 12/17/2008
Supercedes Date: 03/14/2001
Document Group: 06-9232-7
Product Use:
Intended Use:
Specific Use:
Electrical
Part B of two part electrical resin
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
% by Wt
HOMOPOLYMER
DBDPE
DIUNDECYL PHTHALATE
N,N-DI(2-HYDROXYPROPYL)ANILINE
CASTOR OIL
ALUMINUM POTASSIUM SODIUM SILICATE
POLYPROPYLENE ETHER DIOL
DIPROPYLENE GLYCOL
ANTIMONY TRIOXIDE
CARBON BLACK
69102-90-5
1163-19-5
3648-20-2
3077-13-2
8001-79-4
12736-96-8
25322-69-4
25265-71-8
1309-64-4
1333-86-4
20 - 30
20 - 30
10 - 20
1 - 10
1 - 10
1 - 10
1 - 10
1 - 10
1 - 10
1- 5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Smooth black liquid with pungent odor.
General Physical Form: Liquid
Immediate health, physical, and environmental hazards:
May cause allergic skin reaction.
Contains a chemical or
_________________________________________________________________________________________________
Page 1 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
chemicals which can cause cancer. May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Carcinogenicity:
Contains a chemical or chemicals which can cause cancer.
Ingredient
ANTIMONY TRIOXIDE
CARBON BLACK
C.A.S. No.
1309-64-4
1333-86-4
Class Description
Group 2B
Group 2B
Regulation
International Agency for Research on Cancer
International Agency for Research on Cancer
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
_________________________________________________________________________________________________
Page 2 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
Inhalation: Remove person to fresh air.
12/17/2008
If signs/symptoms develop, get medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
OSHA Flammability Classification:
No Data Available
>=290 ºF [Test Method: Closed Cup]
No Data Available
No Data Available
Class IIIB Combustible Liquid
5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may be used to blanket the fire. Wear full protective equipment (Bunker Gear) and a
self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards:
Non-flammable: ordinary combustible material. None inherent in this product.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical
ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition
source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains
and build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with
bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry.
Collect as much of the spilled material as possible. Clean up residue with an appropriate solvent selected by a qualified and
authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Collect the
resulting residue containing solution. Place in a closed container approved for transportation by appropriate authorities. Dispose of
collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid eye contact. Avoid skin contact. Avoid breathing of vapors, mists or spray. Use general dilution ventilation and/or local
exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use
_________________________________________________________________________________________________
Page 3 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
respiratory protection equipment. Do not ingest. Contents may be under pressure, open carefully. For industrial or professional use
only.
7.2 STORAGE
Store away from heat. Keep container in well-ventilated area. Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers. If exhaust
ventilation is not available, use appropriate respiratory protection.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact.
The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient
ANTIMONY TRIOXIDE
ANTIMONY TRIOXIDE
CARBON BLACK
CARBON BLACK
CARBON BLACK
DBDPE
DBDPE
POLYPROPYLENE GLYCOLS
VEGETABLE OIL MISTS
Authority
Type
Limit
ACGIH
CMRG
ACGIH
CMRG
OSHA
AIHA
CMRG
AIHA
OSHA
TWA, as Sb
TWA, as Sb
TWA
TWA
TWA
TWA
TWA
TWA, as aerosol
TWA, as mist
0.5 mg/m3
0.2 mg/m3
3.5 mg/m3
0.5 mg/m3
3.5 mg/m3
5 mg/m3
5 mg/m3
10 mg/m3
10 mg/m3
Additional Information
Table A4
Table Z-1
Table Z-1A
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
_________________________________________________________________________________________________
Page 4 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Smooth black liquid with pungent odor.
Liquid
No Data Available
>=290 ºF [Test Method: Closed Cup]
No Data Available
No Data Available
>=290 ºF
Vapor Density
No Data Available
Vapor Pressure
< 27 psia [@ 131 ºF]
Specific Gravity
pH
Melting point
1.29 [Ref Std: WATER=1]
Not Applicable
Not Applicable
Solubility in Water
Evaporation rate
Volatile Organic Compounds
VOC Less H2O & Exempt Solvents
Nil
No Data Available
No Data Available
No Data Available
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
Carbon dioxide
Oxides of Nitrogen
Oxides of Antimony
During Combustion
During Combustion
During Combustion
During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 5 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility in the presence of a combustible material. As a disposal
alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
LH-A100-0639-9, LH-A100-0640-0, LH-A100-0640-1, LH-A100-0640-2, 80-6107-3193-9
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient
C.A.S. No
ANTIMONY TRIOXIDE (ANTIMONY
COMPOUNDS)
DBDPE
1309-64-4
% by Wt
1 - 10
1163-19-5
20 - 30
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Ingredient (Category if applicable)
C.A.S. No
Regulation
Status
DBDPE
1163-19-5
Applicable
DIUNDECYL PHTHALATE (ALKYL
3648-20-2
Toxic Substances Control Act (TSCA) 4 Test
Rule Chemicals
Toxic Substances Control Act (TSCA) 4 Test
Applicable
_________________________________________________________________________________________________
Page 6 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
PHTHALATES)
DIUNDECYL PHTHALATE
3648-20-2
12/17/2008
Rule Chemicals
Toxic Substances Control Act (TSCA) 4 Test
Rule Chemicals
Applicable
STATE REGULATIONS
Contact 3M for more information.
CALIFORNIA PROPOSITION 65
Ingredient
C.A.S. No.
Classification
ANTIMONY TRIOXIDE
CARBON BLACK
1309-64-4
1333-86-4
**Carcinogen
**Carcinogen
** WARNING: contains a chemical which can cause cancer.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 1
Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 1
Reactivity: 0
Protection: X - See PPE section.
Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and
Coatings Association (NPCA).
_________________________________________________________________________________________________
Page 7 of 8
MATERIAL SAFETY DATA SHEET SCOTCHCAST RESIN 2130 (PART B)
12/17/2008
No revision information is available.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: CC-2 PREP KIT (CABLE CLEANER)
MANUFACTURER: 3M
DIVISION: Electrical Markets Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 07/24/2008
Supercedes Date: 07/22/2008
Document Group: 11-4627-3
Product Use:
Intended Use:
SOLVENT SOAKED RAGS FOR CABLE CLEANING
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
% by Wt
PETROLEUM DISTILLATES
D-LIMONENE
64771-72-8
5989-27-5
80 - 95
5 - 20
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: clear, citrus-like odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Combustible liquid and vapor. Closed
containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an
ignition source and flash back.
May cause allergic skin reaction.
May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
_________________________________________________________________________________________________
Page 1 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Inhalation:
Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, nausea, diarrhea and vomiting.
Chemical (Aspiration) Pneumonitis: Signs/symptoms may include coughing, gasping, choking, burning of the mouth, difficulty
breathing, bluish colored skin (cyanosis), and may be fatal.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
3.3
POTENTIAL ENVIRONMENTAL EFFECTS
VOC Data: 740 grams/liter maximum VOC (less water and exempt compounds). U.S. EPA Waste Number: None. 5 Day Biological
Oxygen Demand (BOD-5) = 77,000 mg/L. Chemical Oxygen Demand (COD) = 290,000 mg/L.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
If signs/symptoms develop, get medical attention.
If Swallowed:
Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious
person. Get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
_________________________________________________________________________________________________
Page 2 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flash Point
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
OSHA Flammability Classification:
No Data Available
>=144 ºF [Test Method: Closed Cup]
144 ºF [Test Method: Closed Cup] [Details: MITS data]
>=165 ºF [Test Method: Open Cup]
No Data Available
No Data Available
Class IIIA Combustible Liquid
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Flammable liquid and vapor. Combustible liquid and vapor. Not applicable. Closed
containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an
ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by
qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with
bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry.
Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities.
Place in a metal container approved for transportation by appropriate authorities. Seal the container.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. No smoking while handling this material. Avoid breathing of vapors,
mists or spray. Avoid eye contact with vapors, mists, or spray. Avoid contact with oxidizing agents.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Store away from
oxidizing agents.
_________________________________________________________________________________________________
Page 3 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers. Use general dilution
ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control mist,
vapor, or spray. If ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Fluoroelastomer (Viton), Nitrile Rubber, Polyethylene.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient
PETROLEUM DISTILLATES
Authority
Type
Limit
CMRG
TWA
300 ppm
Additional Information
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flash Point
Flash Point
Flammable Limits - LEL
clear, citrus-like odor
Liquid
No Data Available
>=144 ºF [Test Method: Closed Cup]
144 ºF [Test Method: Closed Cup] [Details: MITS data]
>=165 ºF [Test Method: Open Cup]
No Data Available
_________________________________________________________________________________________________
Page 4 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
Flammable Limits - UEL
Boiling point
Boiling point
Density
Vapor Density
No Data Available
380.00 - 480.00 ºF
>=95 ºF [Details: MITS data]
0.76 g/ml
>=1.00 [Ref Std: AIR=1]
Vapor Pressure
<=1.0000 mmHg [Details: CONDITIONS: Less than 1 mmHg at 25
C]
Specific Gravity
pH
Melting point
0.76 [Details: MITS data]
7.0
No Data Available
Evaporation rate
Volatile Organic Compounds
VOC Less H2O & Exempt Solvents
Viscosity
Not Applicable
Approximately 740 g/l
No Data Available
No Data Available
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong oxidizing agents
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
Carbon dioxide
Not Specified
Not Specified
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
_________________________________________________________________________________________________
Page 5 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility. As a disposal alternative, dispose of waste product in a
facility permitted to accept chemical waste.
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
78-8061-7605-9, 78-8127-6979-8, 80-6105-9299-2, 80-6112-0013-2, 80-6114-2769-3
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - No
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
The components of this product are listed on the Canadian Domestic Substances List.
Additional Information:
All components are on the TSCA; EINECS; and CDSL Inventories.
_________________________________________________________________________________________________
Page 6 of 7
MATERIAL SAFETY DATA SHEET CC-2 PREP KIT (CABLE CLEANER)
07/24/2008
INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 2
Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 2
Reactivity: 0
Protection: B
Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and
Coatings Association (NPCA).
Revision Changes: Not Applicable
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement