advertisement
QIG 253271827A Fast 1704_GB without WPS.book Page 1 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st™ 1704
Quick Installation Guide
QIG 253271827A Fast 1704_GB without WPS.book Page 1 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Sagem Communications SAS (hereafter referred to as Sagem Communications) thanks you for choosing the range of SAGEM F@st TM 1704 routers while hoping that it will provide you with full satisfaction.
SAGEM F@st TM 1704 products adapt the ADSL function respectively on POTS (ITU G.992.1/3/5 -
Appendix A) and on ISDN (ITU G.992.1/3/5 - Appendix B).
SAGEM F@st TM 1704 equipment include four ethernet interfaces (LAN1 to LAN4).
In addition, this router will provide you with access to all the services provided by your Internet Access
Provider, as shown in the diagram below.
The CE marking certifies that the product complies with the essential requirements of the Directive
1999/5/EC concerning radio equipment and telecommunication equipment, and of Directives 2006/95/EC concerning safety and 2004/108/EC concerning electromagnetic compatibility, defined by the European
Parliament and Council to reduce electromagnetic interferences and protect the health and safety of users.
The product named SAGEM F@st TM 1704 can be operated in the European Union without restrictions indoor but cannot be operated in France in the whole of the band until further notice.
The CE declaration of conformity can be viewed in the support section of the Sagem Communications site www.sagem-communications.com, or it can be obtained from the following address:
Sagem Communications SAS - Customer relations department
250, Route de l'Empereur
92500 RUEIL MALMAISON - FRANCE
Copyright © Sagem Communications SAS
All rights reserved.
SAGEM F@st TM is a registered trademark of Sagem Communications SAS.
Mac OS ®
Windows
is a registered trademark of Apple Computer, Inc.
® is a registered trademark of Microsoft Corporation.
1
QIG 253271827A Fast 1704_GB without WPS.book Page 2 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Contents
7.3.
2
QIG 253271827A Fast 1704_GB without WPS.book Page 3 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
1. Contents of the pack
Before you carry out the installation, make sure that the pack contains the following elements:
5
6
3
4
Item
1
2
SAGEM F@st
Mains adapter
ADSL line cable used to connect your router to your telephone line
Ethernet cable used to connect your router to the Ethernet port of your computer
Quick Installation Guide
CD-ROM
TM 1704 router
Description
7
8
Filter/Splitter used to connect one phone set and your router to your telephone line*
Microfilter used to connect another phone set to your telephone line*
9 802.11g USB Wi-Fi key*
* Option depending on pack content requested
3
QIG 253271827A Fast 1704_GB without WPS.book Page 4 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
2. Safety instructions
Power supply source
• Do not cover the router’s mains adapter.
• The router comes with its own mains adapter. Do not use another adapter.
• This class II adapter does not need to be grounded (earthed). The connection to the electrical network should comply with the indications given on the label.
• Use a readily accessible mains outlet located near the router. The power supply cord is 2 m long.
• Arrange the power supply cord in such a way as to avoid any accidental power cut to the router.
• The router is designed to be connected to a GG- (ground-to-ground) or GN- (ground-to-neutral) type power supply network.
• The router is not designed to be connected to an electrical installation with IT type diagram (neutral connected to earth through an impedance).
• Protection against short-circuits and leaks between the phase, neutral and earth should be provided by the building’s electrical installation. The power supply circuit for this equipment should be fitted with
16 A overcurrent protection and differential protection.
• Connect the router to the mains via a readily accessible wall socket ensuring the electric cutting.
Location conditions
By choosing an appropriate location, you will preserve the longevity of the device. Ensure that the selected location has the following characteristics:
• Install and use the router inside a building.
• The room temperature must not exceed 45°C.
• The router can be placed on a desktop or fixed vertically in its wall mounting.
• Do not expose the router to strong sunlight or place it near a substantial source of heat.
• Do not place the router in an environment where it could be subjected to considerable steam condensation.
• Do not expose the router to splashes of water.
• Do not cover the router’s casing.
• Do not use the router or its peripherals for outdoor transmissions.
Maintenance
• Never open the casing. This must be done only by qualified personnel approved by your supplier.
• Do not use liquid or aerosol cleaning agents.
Safety level
Primary power source access
Bipolar AC mains socket
DC power supply access
Miniature fixed connector (PWR)
RJ45 Ethernet access
(LAN1 to LAN4)
RJ11 line access (LINE)
HPV (Hazardous Primary Voltage circuit)
SELV (Safety Extra Low Voltage)
SELV
TNV3 (Telecommunication Network Voltage level 3 circuit)
4
QIG 253271827A Fast 1704_GB without WPS.book Page 5 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
3. Connection
Connecting your router
Important
Make sure that the router is not connected to your computer before you start the installation from the CD-ROM.
Make the connections as shown in the diagram below.
Line c able
Note
A "UK" mains adapter can be provided in option according to the customer.
Connecting additional telephones
Make the connections as shown in the diagram below.
5
QIG 253271827A Fast 1704_GB without WPS.book Page 6 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
4. Installation from the
CD-ROM
Important
Make sure that the router is not connected to your computer before you start the installation from the CD-
ROM.
Note
The installation procedure described below was undertaken in Windows
Vista TM . Installation in other Windows ®
(98, ME, 2000 and XP) can be slightly different.
1.
Insert the CD-ROM into the relevant drive of your computer.
2.
The welcome screen appears. Click on Next.
3.
Read carefully the precautions to be taken during the installation then click on Next.
4.
Select the type of installation you want to perform then click on Next. For a first-time installation, select "You want to install your
router modem for the first time".
5.
Select the interface you want to use to connect your router to your computer: Wi-Fi or Ethernet.
Installation by Wi-Fi interface
1.
You selected the Wireless interface (Wi-Fi), click on Next.
2.
Select the wireless connection mode (Wi-Fi).
The following connection modes are available:
• by installing a Wi-Fi USB adapter (or key) on your computer,
• or by using your computer’s built-in Wi-Fi.
USB Wi-Fi adapter
1. You selected Wi-Fi USB adapter, click on
Next.
2.
Follow the instructions displayed onscreen by connecting the USB Wi-Fi adapter to your computer, then configure the Wi-Fi interface.
The following Wi-Fi parameters must be entered:
• SSID,
• Security key.
Depending on the interface you select, refer to the relevant section to proceed with the installation:
•
Installation by Wi-Fi interface, page 6
•
Installation of the Ethernet port, page 8
Important
Whichever mode you select, you must plug in the router and connect it to the
ADSL line.
6
QIG 253271827A Fast 1704_GB without WPS.book Page 7 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
2.
The Internet connection screen appears.
Enter your connection ID and password, then click on Next.
Note
The Wi-Fi security key field only appears if a Wi-Fi security (WEP 128,
WPA-PSK and WPA2-PSK) is assigned to your router. The length of this field depends on the selected security.
The Wi-Fi information is marked on your router.
3.
Once you have filled in the Wi-Fi parameters, click on Next.
4.
The Internet connection screen appears.
Enter your connection ID and password, then click on Next.
Note
This information is provided by your
Internet Service Provider (ISP).
3.
A summary of the completed installation steps appear. Click on Finish to end the installation.
You may now use your Internet access.
Note
This information is provided by your
Internet Service Provider (ISP).
5.
A summary of the completed installation steps appear. Click on Finish to end the installation.
You may now use your Internet access.
Wi-Fi interface integrated into your computer
Important
Before you continue installing your router, you must first configure your computer’s wireless manager.
1. Once you have configured your computer’s wireless manager, click on Next.
7
QIG 253271827A Fast 1704_GB without WPS.book Page 8 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Installation of the Ethernet port
1.
You selected the Use the Ethernet cable, click on Next.
2.
Follow the instructions displayed on screen by plugging in the router supply, switching it on and connecting the ADSL line, then connect your computer to one of the four Ethernet sockets
(LAN1 to LAN4) of the router by using the
Ethernet cable.
Installation of an additional computer
Important
Your router is already connected.
1.
Insert the CD-ROM into the relevant drive of your computer.
2.
The welcome screen appears. Click on Next.
3.
When asked for the installation type, select "You
want to install an additional computer" then click on Next.
4.
The interface selection screen appears.
Select the interface you want to use to install an additional computer in the local network (LAN) then click on Next.
5.
Continue the installation as described in the case of a first-time installation.
Note
Given that the router has already been installed once, you do not need to plug it in or connect the ADSL line.
Once you have made the connections, click on
Next.
3.
The Internet connection screen appears.
Enter your connection ID and password, then click on Next.
Note
This information is provided by your
Internet Service Provider (ISP).
4.
A summary of the completed installation steps appear. Click on Finish to end the installation.
You may now use your Internet access.
8
QIG 253271827A Fast 1704_GB without WPS.book Page 9 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
5. Router supervision
You can monitor the router’s activity and status using the following sources:
• status of the LEDs on the front panel of the router
• using the router’s built-in «DSL Router» HTTP controller, available in the HTTP configuration tool
Status of the LEDs on the front panel
LED
Power
ADSL
Internet Green steady
LAN x
( 1 to 4 )
WLAN
Status
Off
Green
Red
Off
Green steady
Green blinking
Off
Green blinking
Red
Off
Green steady
Green blinking
Off
Green steady
Green blinking
Meaning
Power Off
Power On
Router in rescue mode
ADSL Down
ADSL Up
ADSL Synchronisation in progress
• Power Off or
• The Internet account must be configured
• The Internet account is configured or
• Bridge mode
Tx/Rx traffic
Invalid or unauthorised Internet account
No link detected on the Ethernet port
Ethernet port has detected a link with 100 Mbps device
Tx/Rx traffic at 100 Mbps
Wi-Fi deactivated
WI-Fi activated
Wi-Fi Tx/Rx
9
QIG 253271827A Fast 1704_GB without WPS.book Page 10 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Router supervision
The HTTP configuration tool lets you configure and monitor the router remotely.
To access the HTTP configuration tool:
1. Open your browser.
2.
Enter the router’s IP address or enter the following URL: http://myrouter
3.
In the login screen that appears, enter your username and password.
Note
This information is provided by your
Internet Service Provider (ISP).
The welcome page of the HTTP configuration tool appears.
The router’s activity status is always visible at the top right corner.
You can perform the following actions:
• click on Refresh to update the data displayed
• click on Reboot to restart your router
ADSL information
The following table presents the possible states of the ADSL field:
Status
Green
Yellow
Red
Meaning
ADSL line synchronised
ADSL line synchronising
ADSL line not connected
The Down field displays the nominal downlink bit rate.
The Up field displays the nominal uplink bit rate.
10
QIG 253271827A Fast 1704_GB without WPS.book Page 11 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Internet information
The following table presents the possible states of the Internet field:
Status
Off
Green
Yellow
Red
Message
Adsl Down
Not configured
Router rebooting
Connected
Waiting for ISP
Access denied
Meaning
ADSL line not connected or not activated
The Internet account must be configured
Router is rebooting
The Internet account is configured
ADSL line synchronising
Incorrect Internet account
11
QIG 253271827A Fast 1704_GB without WPS.book Page 12 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
6. Advanced router configuration
Use the HTTP configuration tool to access advanced router settings and configure your equipment according to your needs.
Example of an advanced Wi-Fi configuration:
12
QIG 253271827A Fast 1704_GB without WPS.book Page 13 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
7. Troubleshooting
Many sources of information are available to help you identify and resolve issues you may experience:
•
the LEDs on the front panel of the router (see Status of the LEDs on the front panel, page 9),
•
the HTTP configuration tool (see Router supervision, page 10).
For step-by-step and advanced problem-solving procedures, use the Diagnostic tool available in the
HTTP configuration tool.
If none of the above helps you solve the problem, and you are still having trouble connecting to the
Internet, we recommend that you restart your router and eventually reset the factory configuration. You will then need to re-configure your router as a first-time setup.
Diagnostics tool
To access the Diagnostic tool:
1.
Open the configuration tool (see Router supervision, page 10).
2.
Select the Diagnostics menu.
3.
Click on Test. The Internet connection is tested step-by-step:
• successful tests are marked as a pass.
• unsuccessful tests are marked as a fail.
Note
Status DOWN means that an interface was not detected (LAN or
Wi-Fi).
4.
If a test fails, click on the corresponding Help link to access detailed information and problem-solving procedures.
5.
Click on Test to check the problem is solved and resume the connection tests.
13
QIG 253271827A Fast 1704_GB without WPS.book Page 14 Mercredi, 7. octobre 2009 2:47 14
SAGEM F@st TM 1704
Restarting your router
To restart your router, use one of the following methods:
• press the Power button located on the rear panel of the router,
•
click on the Reboot action of the HTTP configuration tool (see Router supervision, page 10).
Resetting factory configuration
To reset the default settings and therefore restore the router to its factory configuration, use one of the following methods:
• press and hold for about 10 seconds the Reset button located on the rear panel of the router,
• in the HTTP configuration tool, select Management > Settings > Restore default.
14
QIG 253271827A Fast 1704_GB without WPS.book Page 15 Mercredi, 7. octobre 2009 2:47 14
Sagem Communications SAS
Broadband & Residential Terminals Business Unit
Headquarters: 250, route de l'Empereur
92500 Rueil-Malmaison - FRANCE www.sagem-communications.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project