Desoldering Iron - Howard Electronic Instruments

Desoldering Iron - Howard Electronic Instruments
www.jbctools.com
Desoldering Iron
Ref. DR560
Packing List
MANUAL
DR560-A
Desoldering Iron
w w w.jbctools.com
Desoldering Iron
Ref. Dr560
C560013
0812360
Internal
Joint Case
0965760
Long cleaning
tips set
C560004
C560005
0780840
Filter
0786640 Cleaning stick
0965970
Cleaning tips set
0780550
Spanner
0812630 Metal tin diposit
0812620 Tin diposit
2
w w w.jbctools.com
Features
MS-A
Desoldering Pump
Control Unit
Mains
Equipotential connection
Connectable control units:
DI, DD, DM and RM.
DR560-A
Desoldering Iron
DR-SD
Desoldering Stand
Desoldering process
Use the tip model with a larger diameter than the
pad to be desoldered, so as to achieve maximum
aspiration and thermal efficiency.
1
2
3
1. Apply the desoldering iron tip so that the
component terminal penetrates within its orifice.
2. When the solder liquefies, start gently to rotate
the desoldering tip so that the compo­nent’s terminal
can be eased away from the sides.
3. Press then, not before, the vacuum pump
push-button just long enough to aspirate the solder.
After pressing the desoldering key there is a slight
delay until the self-contained vacuum pump stops,
this is to make sure that the vacuum circuit is
completely empty.
If any solder remains are left on any terminal after
attempting to desolder it, resolder it with fresh solder
and repeat the desoldering operation.
3
Changing Tips
This operation should be done while the tip is hot,
at a minimum temperature of 250°C, so that any tin
left inside is in molten state.
250º C min.
- Unscrew the tip to be replaced, with the aid of
the spanner supplied.
- Fit the new tip, and tighten up with the spanner
to achieve a good air tightness.
Compatible Tips
The DR560 works with C560 tips. Find the model that best suits your soldering needs in www.jbctools.com
See here some of them in real size:
A ø
B ø
C560-001
ØA=1,4 ØB=0,6 Ømax. pin=0,4
C560-002
C560-001
C560-014
ØA=2,5 ØB=0,8 Ømax. pin=0,6
C560-002
C560-003
ØA=3,2 ØB=1,3 Ømax. pin=1,1
C560-004
4
ØA=2,7 ØB=1 Ømax. pin=0,8
C560-003
C560-014
C560-004
ØA=1,8 ØB=0,8 Ømax. pin=0,6
C560-009
ØA=5 ØB=1,3 Ømax. pin=1,1
C560-009
w w w.jbctools.com
Changing the Heating Element
2
1
1. To perform this operation, shut down the
station or disconnect the tool, the deposit lid
needs to be loosened.
3
2. Undo the screw indicated in the picture and
remove the heating element.
3. Place the new heating element.
Important.
- For a good connection it is essential to insert
the cartridge lining up the mark
.
- Tighten the screw indicated in the picture 2
and then tighten the lid 1.
5
Maintenance
Before carrying out maintenance or storage, always unplug the tool.
- Check periodically that the metal parts are clean to ensure a good detection when it is in the stand.
Use a damp cloth or alcohol.
- Periodically check all cables and tubes connections.
- Replace any defective or damaged pieces. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.
Tin Deposit Maintenance
2
1
Check
internal joint
Then its spiral must be removed to clean the inner
part of the deposit with the provided stick.
- The condition of the filter and internal joint must
be checked and replaced if dirty or damaged.
Check filter
3
The deposit needs to be inserted with spiral filter put
into place, positioned between the 2 lines marked
on the tin deposit. Then the whole must be closed
by screwing the lid 1.
For this, the lid needs to be unscrewed with the
DR560 in vertical position.
6
w w w.jbctools.com
Tip Care
- The largest rod that fits in the tip hole should
periodically be passed through in order to clean
the intake tube. You can use any one supplied
with the CL9885 Tip Cleaning Stand.
- Important: DO NOT press the pushbutton
vacuum pump while tinning the desoldering tip,
as the fumes given off by the flux would quickly
soil the ducts and filter of the air circuit.
Safety
It is imperative to follow safety guidelines to protect health and prevent electric
shock, injury, fire or explosions.
- Do not use the kit for any purpose other than soldering or rework. Incorrect use may cause fire.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Do not leave the appliance unattended when it is on.
- It is necessary to turn the station off before changing cartridges. The screw ensures the appropriate
operation of the tool.
- Heat can cause inflamable products to ignite even when out of sight.
- Be careful with the remains of liquid tin. In contact with skin, it can cause burns.
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
to avoid personal harm.
- This appliance can be used by children over the age of eight and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge once they have been
given adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance. Maintenance shall not be carried out by children
unless supervised.
7
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
www.jbctools.com
0008867-0614
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear due to use
or mis-use.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement