Yamaha | RX-V381 | Owner’s Manual | Owner`s Manual - Yamaha Corporation

AV Receiver
Owner's Manual
for U.S.A., Canada and Australia models
Read the supplied booklet “Safety Brochure” before using the unit.
EN
CONTENTS
BEFORE USING THE UNIT
4
6
7
Accessories................................................................................................ 4
Optimizing the speaker settings automatically (YPAO)................ 25
Error messages....................................................................................................................................................................... 27
How to use this manual............................................................................ 4
Warning messages................................................................................................................................................................ 28
Remote control.......................................................................................... 4
PLAYBACK
Insert the batteries................................................................................................................................................................... 4
Operating range of the remote control........................................................................................................................... 4
FEATURES
Selecting an on-screen menu language.......................................... 24
29
Basic playback procedure...................................................................... 29
5
Enjoying playback................................................................................................................................................................. 29
What you can do with the unit................................................................. 5
Selecting the input source and favorite settings with one touch
(SCENE).................................................................................................... 30
Switching information on the front display................................................................................................................. 29
Part names and functions......................................................................... 7
Selecting a registered scene.............................................................................................................................................. 30
Front panel................................................................................................................................................................................. 7
Registering a scene............................................................................................................................................................... 30
Front display (indicators)....................................................................................................................................................... 8
Rear panel................................................................................................................................................................................... 9
Selecting the sound mode..................................................................... 31
Remote control....................................................................................................................................................................... 10
Enjoying sound field effects (CINEMA DSP)................................................................................................................. 32
PREPARATIONS
1
2
Enjoying unprocessed playback...................................................................................................................................... 34
11
Enhancing the bass (Extra Bass)....................................................................................................................................... 35
Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed
Music Enhancer)..................................................................................................................................................................... 35
Placing speakers............................................................................... 12
Typical speaker layouts....................................................................................................................................................... 13
Listening to FM/AM radio....................................................................... 36
Other speaker layouts.......................................................................................................................................................... 14
Setting the frequency steps............................................................................................................................................... 36
Setting the speaker impedance....................................................................................................................................... 15
Selecting a frequency for reception............................................................................................................................... 36
Connecting speakers........................................................................ 16
Registering favorite radio stations (presets)................................................................................................................ 37
Radio Data System tuning.................................................................................................................................................. 40
Connecting speaker cables................................................................................................................................................ 17
3
Connecting the subwoofer (with built-in amplifier)................................................................................................. 17
Playing back music stored on a Bluetooth® device.............................. 41
Connecting a TV/playback devices.................................................. 18
Playback of Bluetooth® device contents....................................................................................................................... 42
Connecting a Bluetooth® device (pairing).................................................................................................................... 41
Input/output jacks and cables.......................................................................................................................................... 18
Disconnecting a Bluetooth® connection....................................................................................................................... 42
Connecting a TV..................................................................................................................................................................... 19
Configuring playback settings for different playback sources
(Option menu)......................................................................................... 43
Connecting video devices (such as BD/DVD players).............................................................................................. 20
Connecting audio devices (such as CD players)......................................................................................................... 22
Option menu items............................................................................................................................................................... 43
Connecting to the jack on the front panel................................................................................................................... 22
4
Connecting the FM/AM antennas.................................................... 23
5
Connecting the power cable............................................................ 23
2
En
CONFIGURATIONS
47
Video signal flow.................................................................................... 74
Information on HDMI.............................................................................. 75
Configuring various functions (Setup Menu)....................................... 47
HDMI Control.......................................................................................................................................................................... 75
Setup menu items................................................................................................................................................................. 48
Audio Return Channel (ARC)............................................................................................................................................. 77
Speaker...................................................................................................................................................................................... 50
HDMI signal compatibility.................................................................................................................................................. 77
HDMI........................................................................................................................................................................................... 53
Trademarks............................................................................................. 78
Sound......................................................................................................................................................................................... 55
Specifications.......................................................................................... 79
ECO............................................................................................................................................................................................. 57
Function.................................................................................................................................................................................... 58
Language.................................................................................................................................................................................. 60
Configuring the system settings (ADVANCED SETUP menu).............. 61
ADVANCED SETUP menu items........................................................................................................................................ 61
Changing the speaker impedance setting (SP IMP.)................................................................................................. 61
Selecting the remote control ID (REMOTE ID)............................................................................................................. 62
Changing the FM/AM tuning frequency setting (TU)............................................................................................... 62
Switching the video signal type (TV FORMAT)............................................................................................................ 62
Selecting the HDMI 4K signal format (4K MODE)....................................................................................................... 62
Restoring the default settings (INIT)............................................................................................................................... 63
Checking the firmware version (VERSION)................................................................................................................... 63
APPENDIX
64
Frequently asked questions................................................................... 64
Troubleshooting..................................................................................... 65
First, check the following:................................................................................................................................................... 65
Power, system and remote control................................................................................................................................. 65
Audio.......................................................................................................................................................................................... 66
Video.......................................................................................................................................................................................... 68
FM/AM radio............................................................................................................................................................................ 69
Bluetooth®................................................................................................................................................................................ 70
Error indications on the front display................................................... 71
Glossary................................................................................................... 72
Audio information................................................................................................................................................................. 72
HDMI and video information............................................................................................................................................. 73
Yamaha technologies.......................................................................................................................................................... 73
Supported devices.................................................................................. 74
Supported devices................................................................................................................................................................ 74
3
En
BEFORE USING THE UNIT
Accessories
Remote control
Check that the following accessories are supplied with the product.
The supplied remote control is used as follows.
£ AM antenna
Insert the batteries
£ FM antenna
Insert the batteries the right way round.
* One of the above is supplied depending on
the region of purchase.
£ YPAO microphone
£ Remote control
£ Batteries (AAA, R03, UM-4) (x2)
Operating range of the remote control
£ CD-ROM (Owner's Manual)
£ Easy Setup Guide
Point the remote control at the remote control sensor on the unit and remain within the
operating range shown below.
£ Safety Brochure
How to use this manual
• Some features are not available in certain regions.
Within 6 m (20 ft)
• Due to product improvements, specifications and appearance are subject to
change without notice.
30°
• This manual explains operations using the supplied remote control.
Notice:
Indicates precautions for use to avoid the possibility of malfunction/damage to the unit.
Note:
Indicates instructions and supplementary explanations for optimum use.
4
En
30°
FEATURES
What you can do with the unit
The unit is equipped with full of useful functions.
Supports 2- to 5.1-channel speaker system
The ECO mode (power saving function) allows you to
create an eco-friendly home theater system
You can enjoy your favorite acoustic spaces in various styles.
When the ECO mode is enabled, you can reduce the unit's power consumption.
• “ECO Mode” (p.57)
YPAO automatically optimizes the speaker settings to suit your room.
Sequential operation of a TV, AV receiver, and
BD/DVD player (HDMI Control)
• “Optimizing the speaker settings automatically (YPAO)” (p.25)
CINEMA DSP allows you to create stereo or multichannel sounds with
the sound fields like actual movie theaters and concert halls in your
own room.
When the unit is connected to an HDMI Control-compatible TV and BD/DVD player
with each HDMI cable, you can control the unit (such as power and volume) and
BD/DVD player with TV remote control operations.
• “Enjoying sound field effects (CINEMA DSP)” (p.32)
• “HDMI Control” (p.75)
You can enjoy compressed music with enhanced sound (Compressed
Music Enhancer).
Supports Bluetooth® devices
• “Playing back digitally compressed formats (such as MP3, etc.) with enriched sound
(Compressed Music Enhancer)” (p.35)
You can play back music stored on a Bluetooth device.
Change the input source and favorite settings with
one touch (SCENE)
• “Playing back music stored on a Bluetooth® device” (p.41)
Connecting various devices
The SCENE function allows you to select the input source and settings registered to
the corresponding scene, such as sound program and Compressed Music Enhancer
on/off, with just one touch.
A number of HDMI jacks and various input/output jacks on the unit allow you to
connect video devices (such as BD/DVD players), audio devices (such as CD
players), game consoles, portable audio player, and other devices.
• “Selecting the input source and favorite settings with one touch (SCENE)” (p.30)
• “Connecting a TV/playback devices” (p.18)
4K Ultra HD signal and HDCP 2.2 supported
You can enjoy the high definition video quality of 4K with HDCP 2.2 that complies with
the latest copyright protection.
• “Selecting the HDMI 4K signal format (4K MODE)” (p.62)
5
En
Playing back TV audio in surround sound with a
single HDMI cable connection (Audio Return
Channel: ARC)
Useful applications
The useful application for connections and operations of the unit is as follows.
n Application for tablets “AV SETUP GUIDE”
When using an ARC -compatible TV, you only need one HDMI cable to enable video
output to the TV, audio input from the TV, and the transmission of HDMI Control
signals.
AV SETUP GUIDE is an application that assists you with cable connections
between AV Receiver and source devices as well as AV Receiver setup. This
app guides you through the various settings such as speaker connections, TV
and source device connections.
• “Connecting a TV” (p.19)
Surround playback with 5 speakers placed in front
Functions:
1) Connection support guide
– Speaker connection
– TV/source devices connection
You can enjoy the surround sound even when the surround speakers are placed in
front.
• “Enjoying sound field effects without surround speakers (Virtual CINEMA
DSP)” (p.33)
2) Setup support guide
– Various setup assistance with illustrations.
– YPAO setting guidance
Enhanced bass reproduction
3) View Owner's Manual
Extra Bass allows you to enjoy enhanced bass reproduction that does not depend on
the speakers used.
• “Enhancing the bass (Extra Bass)” (p.35)
* This application is for tablets only.
Listening to FM/AM radio
For details, search for “AV SETUP GUIDE” on the App Store or Google Play™.
The unit is equipped with a built-in FM/AM tuner. You can register up to 40 favorite
radio stations as presets.
• “Listening to FM/AM radio” (p.36)
Easy operation with a TV screen
You can view information, or easily configure the settings using the on-screen menu.
Auto Rename function
The unit creates an input source name, displayed on the front display, automatically
according to the connected HDMI-compatible device.
• “Input Rename” (p.58)
6
En
Part names and functions
The part names and functions of the unit and the supplied remote control are as follows.
Front panel
1
2
3 4 5
6
7
8
9
YPAO MIC
INFO
MEMORY (PAIRING)
PRESET
FM
AM
TUNING
VOLUME
SCENE
BD
DVD
CD
TV
RADIO
AUX
PHONES
INPUT
TONE CONTROL
STRAIGHT
PROGRAM
SILENT CINEMA
AUDIO
0
1 z (power) key
Turns on/off (standby) the unit.
2 YPAO MIC jack
For connecting the supplied YPAO microphone (p.25).
3 Remote control sensor
Receives remote control signals (p.4).
4 INFO key
Selects the information displayed on the front display
(p.29).
5 MEMORY (PAIRING) key
Registers FM/AM radio stations as preset stations (p.37).
Starts pairing with a Bluetooth device by holding down for 3
seconds (p.41).
6 PRESET keys
Select a preset FM/AM radio station (p.39).
7 FM and AM keys
Switch between FM and AM (p.36).
A
BC D
E
F
G
E STRAIGHT key
8 TUNING keys
Select the radio frequency (p.36).
Enables/disables the straight decode mode (p.34).
F AUX jack
9 Front display
For connecting devices, such as portable audio players
(p.22).
Displays information (p.8).
: PHONES jack
G VOLUME knob
For connecting headphones.
Adjusts the volume.
A INPUT keys
Select an input source.
B TONE CONTROL key
Adjusts the high-frequency range and low-frequency range
of output sounds (p.44).
C SCENE keys
Select the registered input source and sound program with
one touch. Also, turns on the unit when it is in standby
mode (p.30).
D PROGRAM keys
Select a sound program or a surround decoder (p.31).
7
En
Front display (indicators)
2
1
3
4
5
ENHANCER STEREO TUNED
OUT
6
7
8
SLEEP MUTE
VOL.
ADAPTIVE DRC
SL
9
A
0
1 HDMI
Lights up when HDMI signals are being input or output.
OUT
Lights up when HDMI signals are being output.
2 ENHANCER
Lights up when Compressed Music Enhancer (p.35) is
working.
3 CINEMA DSP
Lights up when CINEMA DSP (p.32) is working.
4 STEREO
Lights up when the unit is receiving a stereo FM radio
signal.
0
: Cursor indicators
Indicate the remote control cursor keys currently
operational.
A Information display
Displays the current status (such as input name and sound
mode name). You can switch the information by pressing
INFO (p.29).
B Speaker indicators
Indicate speaker terminals from which signals are output.
A Front speaker (L)
S Front speaker (R)
D Center speaker
TUNED
F Surround speaker (L)
Lights up when the unit is receiving an FM/AM radio station
signal.
G Surround speaker (R)
5 Bluetooth indicator
Light up while the unit is connecting to a Bluetooth device.
L Subwoofer
C ADAPTIVE DRC
Lights up when Adaptive DRC (p.44) is working.
6 SLEEP
Lights up when the sleep timer is on.
7 MUTE
Blinks when audio is temporarily muted.
8 Volume indicator
Indicates the current volume.
9 ECO
Lights up when the eco mode (p.57) is enabled.
8
En
L C R
SW
SR
B
C
Rear panel
2
1
5
▪ The area around the video/audio output jacks is marked in white
on the actual product to prevent improper connections.
6
3
7
4
8
7 SUBWOOFER PRE OUT jack
For connecting to a subwoofer (with built-in amplifier)
(p.16).
8 SPEAKERS terminals
1 HDMI OUT jack
For connecting to an HDMI-compatible TV and outputting
video/audio signals (p.18). When using ARC, TV audio
signal can also be input through the HDMI OUT jack.
2 HDMI 1–4 jacks
For connecting to speakers (p.16).
9 VOLTAGE SELECTOR
(Taiwan, Brazil and General models only)
Selects the switch position according to your local voltage
(p.23).
For connecting to HDMI-compatible playback devices and
inputting video/audio signals (p.19).
3 ANTENNA jacks
For connecting to FM and AM antennas (p.23).
4 Power cable
For connecting to an AC wall outlet (p.23).
5 AV jacks
AUDIO jacks
For connecting to video/audio playback devices and
inputting video/audio signals (p.20).
6 MONITOR OUT jacks
For connecting to a TV and outputting video signals
(p.18).
9
En
9
Remote control
1
1 Remote control signal transmitter
C OPTION key
2 SLEEP key
2
0
SLEEP
SCENE
3
BD
DVD
TV
STRAIGHT
4
CD
RADIO
ENHANCER
BASS
Pressing this key repeatedly will specify the time (120 min,
90 min, 60 min, 30 min, off), in which the unit switches to
the standby mode.
3 SCENE keys
Select the registered input source and sound program with
one touch. Also, turn on the unit when it is in standby mode
(p.30).
PROGRAM
4 Sound mode keys
FM
Select a sound mode (p.31).
AM
5
INPUT
VOLUME
A
BLUETOOTH
5 Input selection keys
Select an input source for playback.
6 SETUP key
MUTE
6
Displays the setup menu (p.47).
7 Menu operation keys
SETUP
OPTION
ENTER
7
RETURN
TOP MENU
DISPLAY
HOME
POP-UP/MENU
8
C
Cursor keys
Select a menu or the parameter.
ENTER
Confirms a selected item.
RETURN
Returns to the previous screen.
789 External device operation keys
Let you control playback of the HDMI Control-compatible
playback device.
Note
RED
GREEN
YELLOW
BLUE
MEMORY
9
B
TUNING
TUNING
PRESET
B MUTE key
Mutes the audio output.
Transmits infrared signals.
▪ The playback devices must support HDMI Control. Some
HDMI Control-compatible devices cannot be used.
▪ You can assign the unit's functions to the RED/GREEN/
YELLOW/BLUE keys (p.60).
9 Radio keys
Operate the FM/AM radio when “TUNER” is selected as the
input source (p.36).
MEMORY
Registers FM/AM radio stations as
presets.
PRESET
Select a preset station.
TUNING
Select the radio frequency.
: z (receiver power) key
Turns on/off (standby) the unit.
A VOLUME keys
Adjust the volume.
10
En
Displays the option menu (p.43).
PREPARATIONS
General setup procedure
1 Placing speakers................................................................................................................................ (p.12)
2 Connecting speakers........................................................................................................................ (p.16)
3 Connecting a TV/playback devices.................................................................................................. (p.18)
4 Connecting the FM/AM antennas.................................................................................................... (p.23)
5 Connecting the power cable............................................................................................................ (p.23)
6 Selecting an on-screen menu language.......................................................................................... (p.24)
7 Optimizing the speaker settings automatically (YPAO)................................................................ (p.25)
This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!
11
En
1 Placing speakers
Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer in your room. This section describes the representative speaker
layout examples.
Notice
▪ (U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.15).
▪ (Except for U.S.A. and Canada models)
Use speakers with an impedance of at least 6 W.
▪ Use a subwoofer with built-in amplifier.
▪ Be sure to connect the front left and right speakers.
12
En
Typical speaker layouts
n 5.1-channel system
n 5.1-channel system (Virtual CINEMA FRONT)
We recommend this speaker layout which can maximize the performance of the unit.
We recommend this speaker layout when the speakers can't be placed in back of the
room.
1
1
2
2
4
9
9
3
4
5
10° to 30°
Speaker type
Front (L/R)
Center
Surround (L/R)
Subwoofer
5
3
Abbr.
1/2
3
4/5
9
10° to 30°
Speaker type
Function
Produce front left/right channel sounds (stereo sounds).
Front (L/R)
Produces center channel sounds (such as movie dialogue
and vocals).
Center
Produce surround left/right channel sounds.
Surround (L/R)
Produces LFE (low-frequency effect) channel sounds and
reinforces the bass parts of other channels.
Subwoofer
This channel is counted as “0.1”.
Abbr.
1/2
3
4/5
9
Function
Produce front left/right channel sounds (stereo sounds).
Produces center channel sounds (such as movie dialogue
and vocals).
Produce surround left/right channel sounds. By this
system, place the surround speakers in front.
Produces LFE (low-frequency effect) channel sounds and
reinforces the bass parts of other channels.
This channel is counted as “0.1”.
Note
Note
▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system).
▪ To utilize this configuration, set “Virtual CINEMA FRONT” (p.51) in the “Setup” menu to “On”.
▪ You can place the subwoofer either in the left or right side.
▪ You can enjoy surround sound even without the center speaker (front 4.1-channel system).
▪ You can place the subwoofer either in the left or right side.
13
En
Other speaker layouts
The following speaker layouts are also available.
n 2.1-channel system
n 3.1-channel system
1
9
2
1
3
9
14
En
2
Setting the speaker impedance
(U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm speakers. When connecting
6-ohm speakers, set the speaker impedance to “6 Ω MIN”.
1
2
Before connecting speakers, connect the power cable to an AC
wall outlet.
While holding down STRAIGHT on the front panel, press z
(power).
z (power)
STRAIGHT
3
Check that “SP IMP.” is displayed on the front display.
CHARGE
OUT 1 2
ECO
ENHANCER STEREO TUNED
PARTY SLEEP MUTE
ZONE ZONE
2 A 3 B VOL.
SP IMP.••8¬MIN
4
5
ADAPTIVE DRC VIRTUAL
Press STRAIGHT to select “6 Ω MIN”.
Press z (power) to set the unit to standby mode and remove the
power cable from the AC wall outlet.
You are now ready to connect the speakers.
15
En
2 Connecting speakers
Connect the speakers placed in your room to the unit. The following diagrams provide connections for a 5.1-channel system as an example. For other systems, connect speakers
while referring to the connection diagram for the 5.1-channel system.
Notice
▪ Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before connecting the speakers.
▪ The speaker has the polarity (+/-). Connect the speaker cable correctly between the positive (+) terminal of the unit and the speaker, and also between the negative (-) terminal of them.
Cables required for connection (commercially available)
Speaker cables (x the number of speakers)
+
–
Audio pin cable (x1: for connecting a subwoofer)
+
–
The unit (rear)
Precaution for connecting of the speaker cables
1
2
3
4
1
10 mm (3/8”)
10 mm (3/8”)
Improper connecting of the speaker cables may cause short circuit and
also damage the unit or the speakers.
2
▪ Twist the bare wires of the speaker cables
firmly together.
3
4
▪ Do not let the core wires of the speaker cable
touch one another.
▪ Do not let the core wires of the speaker cable
come into contact with the unit’s metal parts
(rear panel and screws).
Audio pin cable
Use a subwoofer with built-in amplifier.
9
Subwoofer
5
Surround (R)
4
Surround (L)
3
2
1
Center
Front (R)
Front (L)
16
En
If “Check SP Wires” appear on the front display when the unit is turned
on, turn off the unit, and then check the speaker cables short circuit.
n Connecting center/surround speakers
Connecting speaker cables
1
Speaker cables have two wires. One is for connecting the negative (-) terminal of the
unit and the speaker, and the other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to the negative and the other wire
to the positive terminal.
2
3
4
n Connecting front speakers
1
2
3
4
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable, and twist the bare wires of the cable firmly
together.
Remove approximately 10 mm (3/8”) of insulation from the ends of
the speaker cable, and twist the bare wires of the cable firmly
together.
Press down the tab.
Insert the bare wires of the cable into the hole in the terminal.
Release the tab.
SU
RR
OU
ND
Loosen the speaker terminal.
ER
d
Insert the bare wires of the cable into the gap on the side (upper
right or bottom left) of the terminal.
FR
ON
T
d
a
Audio pin cable
AV 2
AV 3
Using a banana plug
(U.S.A., Canada, Australia, Taiwan, Brazil and General models only)
Tighten the speaker terminal.
Insert a banana plug into the end of the terminal.
a
- (black)
Use an audio pin cable to connect the subwoofer.
- (black)
1
2
+ (red)
Connecting the subwoofer (with built-in amplifier)
c
b
b
c
Tighten the terminal.
+ (red)
CE
NT
a
FR
ON
T
Banana plug
b
17
En
3 Connecting a TV/playback devices
The unit is equipped with a variety of input jacks
including HDMI input jacks to allow you to connect
different types of playback devices. For information on
how to connect a Bluetooth device see the following
pages.
• Connecting a Bluetooth device (p.41)
n Video jacks
AUDIO jacks
(Stereo L/R jacks)
VIDEO jacks
Transmit analog video signals. Use a video pin
cable.
Input/output jacks and cables
Transmit analog stereo audio signals. Use a stereo
pin cable (RCA cable).
Stereo pin cable
Video pin cable
n Video/audio jacks
HDMI jacks
n Audio jacks
Transmit digital video and digital sound through a
single jack. Use an HDMI cable.
HDMI cable
OPTICAL jacks
Transmit digital audio signals. Use a digital optical
cable. Remove the tip protector (if available) before
using the cable.
Note
▪ Use a 19-pin HDMI cable with the HDMI logo. We
recommend using a cable less than 5.0 m (16.4 ft) long to
prevent signal quality degradation.
▪ The unit’s HDMI jacks support the HDMI Control, Audio
Return Channel (ARC), and 3D and 4K Ultra HD video
transmission (through output) features.
▪ Use high speed HDMI cables to enjoy 3D or 4K Ultra HD
videos.
(Stereo mini jack)
Transmits analog stereo audio signals. Use a
stereo mini-plug cable.
Digital optical cable
OPTICAL
COAXIAL jacks
Transmit digital audio signals. Use a digital coaxial
cable.
Digital coaxial cable
18
En
Stereo mini-plug cable
Connecting a TV
n Composite video connection
Connect a TV to the unit so that video input to the unit can be output to the TV. You
can also enjoy playback of TV audio on the unit.
When connecting any video device with a video pin cable, connect the TV to the
MONITOR OUT (VIDEO) jack.
To maximize the performance of the unit, we recommend connecting a TV with an
HDMI cable.
Note
n HDMI connection
▪ Operations with TV screen are available only when your TV is connected to the unit via HDMI.
▪ If you connect your TV to the unit with a cable other than HDMI, video input to the unit via HDMI cannot be
output to the TV.
▪ If you will receive TV broadcasts only from the set-top box, you do not need to make an audio cable
connection between the TV and the unit.
Connect the TV to the unit with an HDMI cable and a digital optical cable.
The unit (rear)
HDMI OUT jack
VIDEO (composite video) connection
HDMI input
Connect the TV to the unit with a video pin cable and a digital optical cable.
HDMI
HDMI
HDMI
The unit (rear)
Video input
(composite video)
MONITOR OUT (VIDEO) jack
VIDEO
OPTICAL
O
V
V
MONITOR
OUT
O
OPTICAL
(TV)
AUDIO 1
TV
AUDIO 1 (OPTICAL) jack
Audio output
(digital optical)
OPTICAL
O
Note
O
OPTICAL
(TV)
AUDIO 1
▪ You do not make a digital optical cable connection between the TV and the unit in the following cases:
AUDIO 1 (OPTICAL) jack
– If your TV supports Audio Return Channel (ARC)
– If you will receive TV broadcasts only from the set-top box
▪ If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s
power and volume with the TV’s remote control.
To use HDMI Control and ARC, you need to configure the HDMI settings on the unit.
For details on the settings, see “Information on HDMI” (p.75).
About Audio Return Channel (ARC)
▪ ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a
single HDMI cable, you can output video/audio to the TV or input TV audio to the unit.
▪ When using ARC, connect a TV with an HDMI cable that supports ARC.
19
En
TV
Audio output
(digital optical)
Connecting video devices (such as BD/DVD players)
n Composite video connection
Connect video devices such as BD/DVD players, set-top boxes (STBs) and game
consoles to the unit. Depending on the video/audio output jacks available on your
video device, choose one of the following connections. We recommend using an
HDMI connection if the video device has an HDMI output jack.
Connect a video device to the unit with a video pin cable and an audio cable (digital
coaxial or stereo pin cable). Choose a set of input jacks (on the unit) depending on the
audio output jacks available on your video device.
Output jacks on video device
Video
Note
If the combination of video/audio input jacks available on the unit does not match your video device, change
its combination according to the output jacks of your device (p.21).
Input jacks on the unit
Audio
Digital coaxial
Composite video
n HDMI connection
AV 1 (VIDEO + COAXIAL)
Analog stereo
AV 2–3 (VIDEO + AUDIO)
Digital optical
You need to change the combination
of video/audio input jacks (p.21).
Connect a video device to the unit with an HDMI cable.
Video output
(composite video)
AV 1–3 (VIDEO) jacks
HDMI 1–4 jacks
VIDEO
The unit (rear)
V
V
VIDEO
The unit (rear)
HDMI OUT jack
HDMI
Video device
HDMI
C
C
COAXIAL
HDMI
COAXIAL
L
L
L
L
R
R
R
R
Video device
AV 1 (COAXIAL) jack or AV 2–3
(AUDIO) jacks
If you select HDMI 1–4 as the input source by pressing INPUT, the video/audio played
back on the video device will be output from the unit.
Audio output
(digital coaxial or analog
stereo)
If you select AV 1-3 as the input source by pressing INPUT, the video/audio played
back on the video device will be output from the unit.
Note
To watch videos input to the HDMI 1–4 jacks, you need to connect your TV to the HDMI OUT jack of the unit
(p.19).
Note
To watch videos input to the AV 1–3 (VIDEO) jacks, you need to connect your TV to the MONITOR OUT
(VIDEO) jack of the unit (p.19).
20
En
n Changing the combination of video/audio input jacks
3
If the combination of video/audio input jacks available on the unit does not match your
video device, change its combination according to the output jacks of your device.
You can connect a video device that has the following video/audio output jacks.
Output jacks on video device
Press OPTION.
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
MUTE
OPTION
PROGRAM
FM
Input jacks on the unit
SETUPP
AM
INPUT
OPTION
VOLUME
BLUETOOTH
Video
HDMI
Composite video
Audio
Video
Audio
Digital optical
HDMI 1–4
AUDIO 1 (OPTICAL)
Digital coaxial
HDMI 1–4
AUDIO 2 (COAXIAL)
AV 1 (COAXIAL)
Analog stereo
HDMI 1–4
AV 2–3 (AUDIO)
Digital optical
AV 1–3 (VIDEO)
AUDIO 1 (OPTICAL)
MUTE
SETUP
RETURN
ENTER
DISPLAY
TOP MENU
HOME
POP-UP/MENU
RETURN
RED
GREEN
YELLOW
DISPLAYY
DISPLA
BLUE
MEMORY
TUNING
TOP MENU
TUNING
4
For example, if you have connected a video device to AV 2 (VIDEO) and AUDIO 1
(OPTICAL) jack of the unit, change the combination setting as follows.
ENHANCER STEREO TUNED
SLEEP MUTE
OUT
VOL.
ECO
ADAPTIVE DRC VIRTUAL
Audio In
5
VIDEO
V
V
Use the cursor keys (e/r) to select “AUDIO 1” (audio input
jack to be used).
CHARGE
ENHANCER STEREO TUNED
SLEEP MUTE
OUT
VOL.
ECO
Audio••AUDIO 1
Video device
6
OPTICAL
O
O
OPTICAL
AUDIO 1
1
2
ADAPTIVE DRC VIRTUAL
Press OPTION.
This completes the necessary settings.
(TV)
AUDIO 1 (OPTICAL) jack
POP-UP/MENU
Use the cursor keys (q/w) to select “Audio In” and press
ENTER.
CHARGE
Video output
(composite video)
AV 2 (VIDEO) jack
HOME
PRESET
Necessary setting
The unit (rear)
Cursor keys
ENTER
OPTION
ENTER
If you select “AV 2” as the input source by pressing INPUT, the video/audio
played back on the video device will be output from the unit.
Audio output
(digital optical)
After connecting external devices (such as a TV and playback
devices) and power cable of the unit, turn on the unit.
Press INPUT to select “AV 2” (video input jack to be used) as
the input source.
21
En
Connecting audio devices (such as CD players)
Connecting to the jack on the front panel
Connect audio devices such as CD players and MD players to the unit. Depending on
the audio output jacks available on your audio device, choose one of the following
connections.
Use the AUX jack on the front panel to temporarily connect devices such as portable
audio players to the unit.
Audio output jacks on audio device
Before making a connection, stop playback on the device and turn down the volume
on the unit.
Audio input jacks on the unit
Digital optical
AUDIO 1 (OPTICAL)
Digital coaxial
AUDIO 2 (COAXIAL)
AV 1 (COAXIAL)
Analog stereo
AV 2–3 (AUDIO)
SCENE
BD
DVD
CD
TV
RADIO
AUX
INPUT
TONE CONTROL
PROGRAM
STRAIGHT
AUDIO
The unit (rear)
The unit (front)
O
O
OPTICAL
OPTICAL
C
C
COAXIAL
COAXIAL
L
L
L
Audio device
Portable audio player
L
R
If you select “AUX” as the input source by pressing INPUT, the audio played back on
the device will be output from the unit.
R
R
AV 1–3 jacks
AUDIO 1–2 jacks
R
Note
Audio output
(either digital optical, digital coaxial,
or analog stereo)
You need to prepare the audio cable that matches the output jacks on your device.
If you select AV 1-3 or AUDIO 1-2 as the input source by pressing INPUT, the audio
played back on the audio device will be output from the unit.
22
En
4 Connecting the FM/AM antennas
5 Connecting the power cable
Connect the supplied FM/AM antennas to the unit.
Warning
Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.
(Taiwan, Brazil and General models only)
Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall
outlet. Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create a potential
fire hazard.
FM antenna
AM antenna
Before connecting the power cable
Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110–
120/220–240 V, 50/60 Hz.
The unit (rear)
VOLTAGE SELECTOR
VOLTAGE
SELECTOR
110V–
120V
220V–
240V
The unit (rear)
Assembling and connecting the AM antenna
After all the connections are complete, plug in the power cable.
The unit (rear)
To an AC wall outlet
Hold down
Insert
Release
Note
▪ Unwind only the length of cable needed from the AM antenna unit.
▪ The wires of the AM antenna have no polarity.
23
En
6 Selecting an on-screen menu language
Select the desired on-screen menu language.
1
2
6
Press z (receiver power) to turn on the unit.
Note
The information on the front display is provided in English only.
Turn on the TV and switch the TV input to display video from the
unit (HDMI OUT jack).
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If
not, carry out operations while viewing the front display.
3
4
Press SETUP.
Use the cursor keys to select “Language” and press ENTER.
Setup
Speaker
HDMI
Sound
ECO
Function
Language
RETURN
5
To exit from the menu, press SETUP.
Back
Use the cursor keys to select the desired language.
Language
English
日本語
Français
Deutsch
Español
Русский
Italiano
中文
24
En
7 Optimizing the speaker settings automatically (YPAO)
The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker
connections, measures the distances from them to your listening position(s), and then
automatically optimizes the speaker settings, such as volume balance and acoustic
parameters, to suit your room.
4
Place the YPAO microphone at your listening position and
connect it to the YPAO MIC jack on the front panel.
Note
Note
▪ When you use the front 5.1-channel speaker (Virtual CINEMA FRONT) configuration (p.13), set “Virtual
CINEMA FRONT” (p.51) in the “Setup” menu to “On” beforehand.
Place the YPAO microphone at your listening position (same height as your ears). We recommend
the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the
microphone.
▪ Please note the following when using YPAO.
The unit (front)
– Use YPAO after connecting a TV and speakers to the unit.
– During the measuring process, test tones are output at high volume. Ensure that the test tones do not
frighten small children.
– During the measuring process, you cannot adjust the volume.
– During the measuring process, keep the room as quiet as possible.
– Do not connect headphones.
1
– Do not stand between the speakers and the YPAO microphone during the measurement process (about
3 minutes).
1
2
9
Press z (receiver power) to turn on the unit.
Turn on the TV and switch the TV input to display video from the
unit (HDMI OUT jack).
2
3
4
5
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If
not, carry out operations while viewing the front display.
3
Ear height
Turn on the subwoofer and set the volume to half. If the crossover
frequency is adjustable, set it to maximum.
VOLUME
CROSSOVER/
HIGH CUT
The following screen appears on the TV.
Auto Setup
9
Start
Exit
MIN
MAX
MIN
MAX
25
En
5
7
To start the measurement, use the cursor keys to select “Start”
and press ENTER.
Use the cursor keys (e/r) to select “SAVE” and press ENTER.
Auto Setup
The measurement will start in 10 seconds. Press ENTER to start the
measurement immediately.
Start
Exit
< SAVE >
Note
To stop the measurement temporarily, press RETURN and follow the procedure in “Error
messages” (p.27).
The following screen appears on the TV when the measurement finishes.
The adjusted speaker settings are applied.
Auto Setup
Meaurement Finished
Result
3 / 2 / 0.1 ch
3.0 / 10.5 m
-3.0 / +10.0 dB
ENTER
OK
1
2
3
4
Note
To finish the measurement without saving the result, select “CANCEL”.
8
Disconnect the YPAO microphone from the unit.
This completes optimization of the speaker settings.
1
The number of speakers (front side/rear side/subwoofer)
2
Speaker distance (nearest/farthest)
3
Adjustment range of speaker output level
4
Warning message (if available)
Notice
▪ The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be
exposed to direct sunlight or high temperatures (such as on top of AV equipment).
Note
▪ If any error message (such as E-1) or warning message (such as W-1) appears, see “Error
messages” (p.27) or “Warning messages” (p.28).
▪ A speaker with a problem is indicated by blinking of the speaker indicators in the front display.
▪ If multiple warnings are given (when operating with the front display), use the cursor keys (q/w)
to check the other warning messages.
6
Confirm the results displayed on the screen and press ENTER.
26
En
Error messages
If any error message is displayed during the measurement, resolve the problem and
perform YPAO again.
Error message
Cause
E-1:No Front SP
Front speakers are not
detected.
(E-1:NO FRNT SP)
Auto Setup
ERROR
E-9 : User Cancel
E-2:No Sur. SP
Error message
(E-2:NO SUR SP)
< RETRY >
One of the surround
speakers cannot be
detected.
(E-5:NOISY)
E-7:No MIC
TV screen
(E-7:NO MIC)
ENHANCER STEREO TUNED
CHARGE
OUT
Keep the room quiet and retry YPAO. If
you select “PROCEED”, YPAO takes the
measurement again and ignores any
noise detected.
The YPAO microphone has
been removed.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO.
The YPAO microphone
cannot detect test tones.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
SLEEP MUTE
VOL.
ECO
E-5:NOISY
ADAPTIVE DRC VIRTUAL
E-8:No Signal
Front display
(E-8:NO SIGNAL)
n Procedure to handle errors
1
2
E-9:User Cancel
(E-9:CANCEL)
Check the content of error message and press ENTER.
E-10:Internal Err.
(E-10:INTERNAL)
Use the cursor keys (e/r) to select the desired operation.
To exit the YPAO measurement:
1
2
3
Use the cursor keys (q/w) to select “Exit” and press ENTER.
Disconnect the YPAO microphone from the unit.
Select “RETRY” and press ENTER.
To proceed with the current YPAO measurement (for E-5 and E-9
only):
1
An internal error has
occurred.
Texts in parentheses denote indicators on the front display.
To retry the YPAO measurement from beginning:
1
The measurement has been
Retry or exit YPAO as necessary.
canceled.
Note
Select “EXIT” and press ENTER.
Select “PROCEED” and press ENTER.
27
En
Exit YPAO, turn off the unit, and then
check the speaker connections.
The noise is too loud.
2%
E-5:Noisy
Remedy
Exit YPAO, and turn off and on the unit. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
Warning messages
If a warning message is displayed after the measurement, you can still save the
measurement results by following on-screen instructions.
Warning message
Cause
Check the cable connections (+/-) of the
problem speaker.
However, we recommend you perform YPAO again in order to use the unit with the
optimal speaker settings.
If the speaker is connected incorrectly:
Auto Setup
Meaurement Finished
Result
W-1:Out of Phase
3 / 2 / 0.1 ch
3.0 / 10.5 m
(W-1:PHASE)
-3.0 / +10.0 dB
ENTER
OK
W-1 : Out of Phase
A speaker cable may be
connected with the reverse
polarity (+/-).
Warning message
Problem speaker (blinks)
ENHANCER STEREO TUNED
CHARGE
OUT
W-2:Over Distance
(W-2:DISTANCE)
SLEEP MUTE
VOL.
ECO
W-1:PHASE
ADAPTIVE DRC VIRTUAL
Front display
n Procedure to handle warnings
W-3:Level Error
(W-3:LEVEL)
Check the content of warning message and press ENTER.
Note
Texts in parentheses denote indicators on the front display.
1
If the speaker is connected correctly:
Select “SAVE” and press ENTER.
Select “CANCEL” and press ENTER.
Disconnect the YPAO microphone from the unit.
28
En
Exit YPAO, turn off the unit, and place the
problem speaker within 24 m (80 ft) of the
listening position.
Check the usage environment and cable
connections (+/-) of each speaker, and
the volume of the subwoofer. If there is
There are significant volume any problem, exit YPAO, turn off the unit,
differences between the
and then reconnect speaker cable or
speakers.
correct the speaker positions. We
recommend using the same speakers or
speakers with specifications that are as
similar as possible.
To save the measurement results:
To discard the measurement result:
3
A speaker is placed more
than 24 m (80 ft) from the
listening position.
Use the cursor keys (e/r) to select the desired operation.
1
Turn off the unit, reconnect the speaker
cable.
Depending on the type of speakers or
room environment, this message may
appear even if the speakers are
connected correctly. In this case, you
can ignore the message.
TV screen
1
2
Remedy
PLAYBACK
Basic playback procedure
Enjoying playback
Switching information on the front display
1
1
2
Turn on the external devices (such as a TV or BD/DVD player)
connected to the unit.
Press INFO repeatedly to select between the various display
items.
ENHANCER STEREO TUNED
CHARGE
VOL.
ECO
Item name
SLEEP
TV
CD
RADIO
ENHANCER
BASS
PROGRAM
About 3 seconds after a display item is selected, its corresponding
information appears.
PROGRAM
FM
Input selection keys
AM
INPUT
VOLUME
BLUETOOTH
FM
ENHANCER STEREO TUNED
CHARGE
OUT
MUTE
INPUT
ENTER
RETURN
DISPLAY
TOP MENU
HOME
GREEN
YELLOW
†‡Pro Logic
AM
OPTION
VOLUME
VOLUME
BLUETOOTH
BLUE
Note
TUNING
PRESET
3
MUTE
MUTE
Available items vary depending on the selected input source. The displayed item can also be
applied separately to each input source.
Currently input source
Start playback on the external device or select a radio station.
Item
HDMI
AV
Refer to the instruction manual for the external device.
AUDIO
For details on the following operations, see the corresponding pages.
▪ “Listening to FM/AM radio” (p.36)
AUX
Input (input source name), DSP Program (sound mode name), Audio
Decoder (decoder name*)
Bluetooth
▪ “Playing back music stored on a Bluetooth® device” (p.41)
4
ADAPTIVE DRC VIRTUAL
Information
POP-UP/MENU
MEMORY
TUNING
SLEEP MUTE
VOL.
ECO
SETUP
RED
ADAPTIVE DRC VIRTUAL
Audio Decoder
SCENE
BD
DVD
STRAIGHT
SLEEP MUTE
OUT
Use the input selection keys to select an input source.
Frequency (frequency), DSP Program (sound mode name), Audio
Decoder (decoder name*)
TUNER
Press VOLUME to adjust the volume.
Note
▪ To mute the audio output, press MUTE. Press MUTE again to unmute.
▪ To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL on the front panel
(p.44).
29
(U.K. and Europe models only)
Radio Data System data is also available when the unit is tuned into a
Radio Data System broadcasting station (p.40).
* The name of the audio decoder currently activated is displayed. If no audio decoder
is activated, “Decoder Off” appears.
En
Selecting the input source and favorite settings with one touch (SCENE)
The SCENE function allows you to select the assigned input source, sound program,
and Compressed Music Enhancer on/off with just one touch.
Registering a scene
1
Selecting a registered scene
1
▪ Select an input source (p.29)
Press SCENE.
▪ Select a sound program (p.31) or straight decode (p.34)
The input source and settings registered to the corresponding scene are
selected. The unit turns on automatically when it is in standby mode.
▪ Enable/disable Compressed Music Enhancer (p.35)
2
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
Perform the following operations to prepare the settings you want
to assign to a scene.
Hold down the desired SCENE key until “SET Complete” appears
on the front display.
PROGRAM
CHARGE
ENHANCER STEREO TUNED
SLEEP MUTE
FM
OUT
AM
INPUT
SLEEP
VOLUME
SET Complete
SCENE
MUTE
SETUP
BD
DVD
OPTION
TV
CD
RADIO
ENHANCER
BASS
SCENE
ENTER
RETURN
TOP MENU
RED
STRAIGHT
DISPLAY
HOME
GREEN
YELLOW
POP-UP/MENU
BLUE
PROGRAM
MEMORY
TUNING
TUNING
PRESET
By default, the following settings are registered for each scene.
SCENE
Input
HDMI1
VOL.
ECO
BLUETOOTH
AUDIO1
AUDIO2
TUNER
Sound program
MOVIE (Sci-Fi)
STRAIGHT
STRAIGHT
STEREO
(5ch Stereo)
Compressed Music
Enhancer
Off
On
Off
On
SCENE link playback
On
On
Off
Off
Note
The SCENE link playback function allows you to automatically turn on the TV or start playback of an external
device connected to the unit via HDMI, in conjunction with a scene selection. To enable SCENE link
playback, set “SCENE” (p.54) in the “Setup” menu to “On”.
30
En
ADAPTIVE DRC VIRTUAL
Selecting the sound mode
I want to enjoy listening to compressed music.
The unit is equipped with a variety of sound programs and surround decoders that
allow you to enjoy playback sources with your favorite sound mode (such as sound
field effect or stereo playback).
• Enable Compressed Music Enhancer by pressing ENHANCER (p.35).
This mode lets you enjoy compressed music stored on a Bluetooth device with
additional depth and breadth (p.35).
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
Note
PROGRAM
▪ The sound mode can be applied separately to each input source.
FM
AM
INPUT
VOLUME
SLEEP
MUTE
SCENE
BLUETOOTH
SETUP
OPTION
BD
DVD
TV
CD
RADIO
ENHANCER
BASS
▪ When you play back audio signals with a sampling rate of higher than 96 kHz, the straight decode mode
(p.34) is automatically selected.
▪ You can check which speakers are currently outputting sound by looking at the speaker indicators on the
unit’s front panel (p.8).
ENTER
RETURN
TOP MENU
RED
DISPLAY
HOME
GREEN
YELLOW
BLUE
MEMORY
TUNING
STRAIGHT
POP-UP/MENU
PROGRAM
TUNING
PRESET
STRAIGHT
ENHANCER
BASS
PROGRAM
I want to enjoy viewing video sources such as movies, TV programs, or
games.
• Select a sound program suitable for each video source by pressing PROGRAM
repeatedly (p.32).
I want to enjoy listening to music sources or stereo playback.
• Select a sound program suitable for music or stereo playback by pressing
PROGRAM repeatedly (p.33).
I want to enjoy multichannel playback from 2-channel sources.
• Select a surround decoder in the “Option” menu (p.43).
I want to enjoy unprocessed sounds in original channels.
• Switch to the straight decode mode by pressing STRAIGHT (p.34).
I want to enjoy enhanced bass sounds.
• Enable Extra Bass by pressing BASS (p.35).
31
En
Enjoying sound field effects (CINEMA DSP)
Drama
This program features stable reverberations that match a wide range of
movie genres, from serious dramas to musicals and comedies. The
reverberations are modest, but suitably stereophonic. The sound effects
and background music are reproduced with a gentle echo that does not
impinge on the articulation of the dialogue. You’ll never get tired listening
for long periods.
Mono Movie
This program reproduces monaural video sources, such as classic
movies, in an atmosphere of a good old movie theater. The program
creates a pleasant space with depth, by adding breadth and the
appropriate reverberation to the original audio.
Sports
This program allows listeners to enjoy the rich vividness of sport
broadcasts and light entertainment programs. In sports broadcasts, the
commentators’ voices are positioned clearly at the center, while the
atmosphere inside the stadium is realistically conveyed by the peripheral
delivery of the sounds of the fans in a suitable space.
Action Game
This program is suitable for action games, such as car racing and
fighting games. The reality of, and emphasis on, various effects makes
the player feel like they are right in the middle of the action, allowing for
greater concentration. Use this program in combination with Compressed
Music Enhancer for a more dynamic and strong sound field.
Roleplaying Game
This program is suitable for role-playing and adventure games. This
program adds depth to the sound field for natural and realistic
reproduction of background music, special effects, and dialogue from a
wide variety of scenes. Use this program in combination with
Compressed Music Enhancer for a clearer and more spatial sound field.
The unit is equipped with a variety of sound programs that utilize Yamaha’s original
DSP technology (CINEMA DSP). It allows you to easily create sound fields like actual
movie theaters or concert halls in your room.
Sound program category
“CINEMA DSP” lights up
CHARGE
ENHANCER STEREO TUNED
OUT
SLEEP MUTE
VOL.
ECO
Sci-Fi
ADAPTIVE DRC VIRTUAL
Sound program
Note
You can adjust the sound field effect level in “DSP Level (DSP Level)” (p.44) in the “Option” menu.
n Sound programs suitable for movies (MOVIE)
The following sound programs are optimized for viewing video sources, such as
movies, TV programs, and games.
Standard
This program creates a sound field that emphasizes the surround feeling
without disturbing the original acoustic positioning of multichannel audio,
such as Dolby Digital and DTS. Its design is based on the concept of the
ideal movie theater, in which the audience is surrounded by beautiful
reverberations from the left, right, and rear.
Spectacle
This program delivers the scale and grandeur of spectacular movie
productions. It delivers an expansive sound space to match the
cinemascope wide-screen, and boasts a broad dynamic range,
providing everything from small delicate sounds to powerful loud booms.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of
the latest Sci-Fi and SFX movies. You can enjoy a variety of
cinematographically created virtual spaces reproduced with clear
separation between dialogue, sound effects, and background music.
Adventure
This program is ideal for reproducing the sound design of action and
adventure movies precisely. The sound field restrains reverberations, but
puts emphasis on reproducing a sensation of expansiveness on both
sides, powerful space expanded widely to the left and right. The
restrained depth creates a clear and powerful space, while also
maintaining the articulation of the sounds and the separation of the
channels.
32
En
n Sound programs suitable for music (MUSIC)
n Sound programs suitable for stereo playback (STEREO)
The following sound programs are optimized for listening to music sources.
You can select stereo playback.
Hall in Munich
This program simulates a Munich concert hall with approximately 2,500
seats that uses stylish wood for the interior finishing. Fine, beautiful
reverberations spread richly, creating a calming atmosphere. The
listener’s virtual seat is at the center left of the arena.
Hall in Vienna
This program simulates a 1700-seat, middle-sized concert hall with a
shoebox shape that is traditional in Vienna. Pillars and ornate carvings
create extremely complex reverberations from all around the audience,
producing a very full, rich sound.
Chamber
This program creates a relatively wide space with a high ceiling, like an
audience hall in a palace. It offers pleasant reverberations that are
suitable for courtly music and chamber music.
Cellar Club
This program simulates an intimate concert venue with a low ceiling and
homey atmosphere. A realistic, live sound field delivers powerful sounds
that make you feel as if you are sitting in the front row in front of a small
stage.
The Roxy Theatre
This program creates the sound field of a 460-seat rock music concert
venue in Los Angeles. The listener’s virtual seat is at the center left of the
hall.
The Bottom Line
This program creates the sound field at stage front in The Bottom Line, a
famous New York jazz club once. The floor can seat 300 people to the
left and right in a sound field offering real and vibrant sound.
Music Video
2ch Stereo
Use this program to mix down multichannel sources to 2 channels. When
multichannel signals are input, they are down mixed to 2 channels and
output from the front speakers (this program does not utilize CINEMA
DSP).
5ch Stereo
Use this program to output sound from all speakers. When you play back
multichannel sources, the unit mixes down the source to 2 channels, and
then outputs the sound from all speakers. This program creates a larger
sound field and is ideal for background music at parties.
n Enjoying sound field effects without surround speakers
(Virtual CINEMA DSP)
If you select one of the sound programs (except 2ch Stereo and 5ch Stereo) when no
surround speakers are connected, the unit automatically creates the surround sound
field using the front-side speakers.
n Enjoying surround sound with 5 speakers placed in
front (Virtual CINEMA FRONT)
You can enjoy the surround sound even when the surround speakers are placed in
front.
This program allows you to enjoy videos of pop, rock, and jazz concerts,
as if you were there yourself. Immerse yourself in the hot concert
atmosphere thanks to the vividness of the singers and solos on stage, a
presence sound field that emphasizes the beat of rhythm instruments,
and a surround sound field that reproduces the space of a big live hall.
n Enjoying surround sound with headphones (SILENT
CINEMA)
You can enjoy surround or sound field effects, like a multichannel speaker system, with
stereo headphones by connecting the headphones to the PHONES jack and selecting
a sound program or a surround decoder.
33
En
n Playing back 2-channel sources in multichannel
Enjoying unprocessed playback
(surround decoder)
You can play back input sources without any sound field effect processing.
The surround decoder enables unprocessed multichannel playback from 2-channel
sources. When a multichannel source is input, it works the same way as the straight
decode mode.
n Playing back in original channels (straight decode)
When the straight decode mode is enabled, the unit produces stereo sound from the
front speakers for 2-channel sources such as CDs, and produces unprocessed
multichannel sounds for multichannel sources.
1
For details on each decoder see “Glossary” (p.72).
1
Press STRAIGHT.
Press PROGRAM repeatedly to select a surround decoder.
The previously selected surround decoder is selected. You can change
the surround decoder in “Sur.Decode” (p.43) in the “Option” menu.
Each time you press the key, the straight decode mode is enabled or
disabled.
SLEEP
SCENE
BD
DVD
CHARGE
ENHANCER STEREO TUNED
OUT
SLEEP MUTE
TV
STRAIGHT
VOL.
ECO
STRAIGHT
CD
RADIO
ENHANCER
BASS
PROGRAM
ADAPTIVE DRC VIRTUAL
FM
AM
INPUT
VOLUME
SLEEP
MUTE
SCENE
BLUETOOTH
SETUP
BD
DVD
OPTION
TV
CD
RADIO
ENHANCER
BASS
ENTER
RETURN
TOP MENU
RED
STRAIGHT
DISPLAY
POP-UP/MENU
HOME
GREEN
YELLOW
BLUE
PROGRAM
MEMORY
TUNING
PROGRAM
TUNING
PRESET
“SUR. DECODE” appears
ENHANCER STEREO TUNED
CHARGE
OUT
SLEEP MUTE
VOL.
ECO
†‡Pro Logic
ADAPTIVE DRC VIRTUAL
bPro Logic
Uses the Dolby Pro Logic decoder suitable for all sources.
bPLII Movie
Uses the Dolby Pro Logic II decoder suitable for movies.
bPLII Music
Uses the Dolby Pro Logic II decoder suitable for music.
bPLII Game
Uses the Dolby Pro Logic II decoder suitable for games.
Neo:6 Cinema
Uses the DTS Neo: 6 decoder suitable for movies.
Neo:6 Music
Uses the DTS Neo: 6 decoder suitable for music.
Note
You can adjust the surround decoder parameters in “DSP Parameter” (p.55) in the “Setup” menu.
34
En
Enhancing the bass (Extra Bass)
Playing back digitally compressed formats (such as
MP3, etc.) with enriched sound (Compressed Music
Enhancer)
Extra Bass allows you to enjoy enhanced bass sounds, regardless of the size of the
front speakers and the presence or absence of the subwoofer.
1
Press BASS.
Each time you press the key, Extra Bass is enabled or disabled.
Compressed Music Enhancer adds depth and breadth to the sound, allowing you to
enjoy a dynamic sound close to the original sound before it was compressed. This
function can be used along with any other sound modes.
Note
You can also use “Extra Bass” (p.51) in the “Setup” menu to enable/disable Extra Bass.
1
Press ENHANCER.
Each time you press the key, Compressed Music Enhancer is enabled or
disabled.
“ENHANCER” lights up
CHARGE
ENHANCER STEREO TUNED
OUT
SLEEP MUTE
VOL.
ECO
Enhancer On
ADAPTIVE DRC VIRTUAL
Note
▪ Compressed Music Enhancer does not work on the following audio sources.
– Signals whose sampling rate is over 48 kHz
– High-definition streaming audio
▪ You can also use “Enhancer (Enhancer)” (p.44) in the “Option” menu to enable/disable
Compressed Music Enhancer.
35
En
Listening to FM/AM radio
You can tune into a radio station by specifying its frequency or selecting from
registered radio stations.
4
5
Note
▪ The radio frequencies differ depending on the country or region where the unit is being used. The
explanation of this section uses a display with frequencies used in U.K. and Europe models.
▪ If you cannot obtain good reception on the radio, adjust the direction of the FM/AM antennas.
Press STRAIGHT to select “FM100/AM10”.
Press z (power) to set the unit to standby mode and turn it on
again.
Selecting a frequency for reception
Setting the frequency steps
1
(Asia, Taiwan, Brazil and General models only)
At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz for AM.
Depending on your country or region, set the frequency steps to 100 kHz for FM and
10 kHz for AM.
Press FM or AM to select a band.
“TUNER” is selected as the input source and then the frequency currently
selected is displayed.
CHARGE
OUT
1
2
ECO
When holding down STRAIGHT on the front panel, press z
(power).
z (power)
3
STRAIGHT
Press PROGRAM repeatedly to select “TU”.
CHARGE
OUT
ECO
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
TU••••FM50/AM9
SLEEP MUTE
VOL.
FM 87.50MHz
Set the unit to standby mode.
PROGRAM
ENHANCER STEREO TUNED
ADAPTIVE DRC VIRTUAL
36
En
ADAPTIVE DRC VIRTUAL
2
Registering favorite radio stations (presets)
Press TUNING repeatedly to set a frequency.
You can register up to 40 radio stations as presets. Once you have registered stations,
you can easily tune into them by selecting their preset numbers.
Hold down the key for about a second to search stations automatically.
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
n Registering radio stations automatically (Auto Preset)
PROGRAM
FM
RED
AM
INPUT
VOLUME
GREEN
YELLOW
LO
Automatically register FM radio stations with strong signals (up to 40 stations).
BLUE
BLUETOOTH
TUNING
MEMORY
MUTE
SETUP
Note
OPTION
TUNING
ENTER
RETURN
TUNING
▪ To register AM radio stations, follow “Registering a radio station manually” (p.38).
DISPLAY
TOP MENU
HOME
▪ (U.K. and Europe models only)
Only Radio Data System broadcasting stations are registered automatically by the Auto Preset function.
POP-UP/MENU
PRESET
RED
GREEN
YELLOW
BLUE
MEMORY
TUNING
TUNING
PRESET
CHARGE
OUT
ECO
ENHANCER STEREO TUNED
1
2
3
SLEEP MUTE
VOL.
FM 98.50MHz
ADAPTIVE DRC VIRTUAL
“TUNED” lights up when a signal is received from a radio station.
“STEREO” also lights up when a stereo signal is received.
Press FM to select “TUNER” as the input source.
Press OPTION.
Use the cursor keys to select “Preset” and press ENTER.
CHARGE
OUT
Preset
Note
▪ You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio reception by
selecting “FM Mode” (p.43) in the “Option” menu. When the signal reception for an FM radio
station is unstable, switching to monaural may improve it.
▪ You can watch videos input from external devices while listening to radio by selecting the video
input jack in “Video Out (Video Out)” (p.46) in the “Option” menu.
37
En
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
ECO
ADAPTIVE DRC VIRTUAL
4
n Registering a radio station manually
To start the Auto Preset process, press ENTER.
Select a radio station manually and register it to a preset number.
“SEARCH” appears during Auto Preset
ENHANCER STEREO TUNED
CHARGE
OUT
1
SLEEP MUTE
VOL.
ECO
01:FM 87.50MHz
ADAPTIVE DRC VIRTUAL
2
Preset number from which to start the registration
Follow “Selecting a frequency for reception” (p.36) to tune into
the desired radio station.
Hold down MEMORY for a few seconds.
The first time that you do register a station, the selected radio station will
be registered to the preset number “01”. Thereafter, each radio station
you select will be registered to the next empty (unused) preset number
after the most recently registered number.
Note
▪ To specify the preset number from which to start the registration, press cursor keys (e/r) or
PRESET to select a preset number.
▪ To cancel the Auto Preset process, press RETURN.
When the Auto Preset process finishes, “FINISH” appears and the “Option” menu
closes automatically.
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
PROGRAM
CHARGE
ENHANCER STEREO TUNED
SLEEP MUTE
FM
OUT
VOL.
ECO
Auto Preset
RED
AM
INPUT
VOLUME
ADAPTIVE DRC VIRTUAL
GREEN
YELLOW
LO
BLUE
BLUETOOTH
MEMORY
MEMORY
MUTE
SETUP
OPTION
TUNING
ENTER
RETURN
TUNING
DISPLAY
TOP MENU
HOME
POP-UP/MENU
PRESET
RED
GREEN
YELLOW
BLUE
MEMORY
TUNING
TUNING
PRESET
ENHANCER STEREO TUNED
CHARGE
OUT
SLEEP MUTE
VOL.
ECO
01:FM 98.50MHz
ADAPTIVE DRC VIRTUAL
Preset number
Note
To specify the preset number for registering, press PRESET to select a preset number, and then
press MEMORY.
CHARGE
ENHANCER STEREO TUNED
OUT
SLEEP MUTE
VOL.
ECO
02:Empty
ADAPTIVE DRC VIRTUAL
“Empty” (not in use) or the frequency currently registered
38
En
n Selecting a preset station
n Clearing preset stations
Tune into a registered radio station by selecting its preset number.
Clear radio stations registered to the preset numbers.
1
2
1
2
3
Press FM or AM to select “TUNER” as the input source.
Press PRESET repeatedly to select the desired radio station.
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
Press FM or AM to select “TUNER” as the input source.
Press OPTION.
Use the cursor keys to select “Preset” and press ENTER.
PROGRAM
CHARGE
RED
VOLUME
GREEN
YELLOW
LO
SETUP
TUNING
TUNING
DISPLAY
HOME
POP-UP/MENU
PRESET
RED
4
5
OPTION
ENTER
GREEN
YELLOW
BLUE
PRESET
MEMORY
TUNING
ADAPTIVE DRC VIRTUAL
Preset
MEMORY
MUTE
RETURN
TUNING
PRESET
Use the cursor keys (q/w) to select “CLEAR”.
Use the cursor keys (e/r) to select a preset station to be cleared
and press ENTER.
CHARGE
ENHANCER STEREO TUNED
OUT
OUT
ENHANCER STEREO TUNED
01:FM 98.50MHz
SLEEP MUTE
VOL.
ECO
01:FM 98.50MHz
SLEEP MUTE
VOL.
ECO
CHARGE
SLEEP MUTE
VOL.
ECO
BLUE
BLUETOOTH
TOP MENU
ENHANCER STEREO TUNED
OUT
FM
AM
INPUT
ADAPTIVE DRC VIRTUAL
ADAPTIVE DRC VIRTUAL
Preset station to be cleared
If the preset station is cleared, “Cleared” appears and then the next in-use
preset number is displayed.
Note
“No Presets” appears when no radio stations are registered.
CHARGE
ENHANCER STEREO TUNED
OUT
01:Cleared
6
7
39
En
SLEEP MUTE
VOL.
ECO
ADAPTIVE DRC VIRTUAL
Repeat step 5 until all desired preset stations are cleared.
To exit from the menu, press OPTION.
Radio Data System tuning
n Receiving traffic information automatically
(U.K. and Europe models only)
When “TUNER” is selected as the input source, the unit automatically receives traffic
information. To enable this function, follow the procedure below to set the traffic
information station.
Radio Data System is a data transmission system used by FM stations in many
countries. The unit can receive various types of Radio Data System data, such as
“Program Service”, “Program Type”, “Radio Text” and “Clock Time”, when it is tuned
into a Radio Data System broadcasting station.
1
2
n Displaying the Radio Data System information
1
Use the cursor keys to select “Traffic Program” (TrafficProgram)
and press ENTER.
The traffic information station search will start in 5 seconds. Press ENTER
again to start the search immediately.
Tune into the desired Radio Data System broadcasting station.
Note
Note
We recommend using “Auto Preset” to tune into the Radio Data System broadcasting stations
(p.37).
2
When “TUNER” is selected as the input source, press OPTION.
▪ To search upward/downward from the current frequency, press the cursor keys (q/w) while
“READY” is displayed.
▪ To cancel the search, press RETURN.
Press INFO.
▪ Texts in parentheses denote indicators on the front display.
Each time you press the key, the displayed item changes.
ENHANCER STEREO TUNED
CHARGE
The following screen appears for about 3 seconds when the search
finishes.
SLEEP MUTE
OUT
VOL.
ECO
ADAPTIVE DRC VIRTUAL
Program Type
CHARGE
Note
“TP Not Found” appears for about 3 seconds when no traffic information stations are found.
VOL.
ECO
CLASSICS
ADAPTIVE DRC VIRTUAL
Information
Program service name
Program Type
Current program type
Radio Text
Information on the current program
Clock Time
Current time
DSP Program
Sound mode name
Audio Decoder
Decoder name
Frequency
Frequency
ADAPTIVE DRC VIRTUAL
Traffic information station (frequency)
SLEEP MUTE
OUT
Program Service
VOL.
TP FM101.30MHz
About 3 seconds later, the corresponding information for the displayed
item appears.
ENHANCER STEREO TUNED
SLEEP MUTE
ECO
Item name
CHARGE
ENHANCER STEREO TUNED
OUT
Note
“Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not displayed if the radio
station does not provide the Radio Data System service.
40
En
Playing back music stored on a Bluetooth® device
You can play back music files stored on a Bluetooth device on the unit.
4
Please also refer to the owner’s manual of your Bluetooth device.
Note
After pairing has been completed and the unit is connected to the
Bluetooth device, “Connected” appears on the front display. While a
Bluetooth connection is established, the Bluetooth indicators light up.
▪ The Bluetooth device must support A2DP.
▪ You cannot play back video files stored on a Bluetooth device on the unit.
Connecting a Bluetooth® device (pairing)
CHARGE
SLEEP MUTE
VOL.
ECO
Connected
ADAPTIVE DRC VIRTUAL
SL
L C R
SW
SR
Note
▪ If you are prompted to input a passkey during a pairing procedure, input the numerals “0000”.
▪ Complete a pairing procedure within 30 seconds.
▪ If no Bluetooth devices are found, “Not found” appears.
Press BLUETOOTH to select “Bluetooth” as the input source.
Hold down MEMORY on the front panel or the remote control for
more than 3 seconds.
“Searching…” appears on the front display.
Note
▪ You can also use the “Option” menu to pair a Bluetooth device. Press OPTION, and then use the
cursor keys to select “Pairing”.
▪ If another Bluetooth device is already connected, disconnect the Bluetooth connection before
you perform a pairing operation.
▪ To cancel pairing, press MEMORY.
3
ENHANCER STEREO TUNED
OUT
When connecting a Bluetooth device to the unit for the first time, the pairing operation
is required to perform. Pairing is an operation that registers the Bluetooth devices with
each other beforehand. Once pairing has been completed, subsequent reconnection
will be easy even after the Bluetooth connection is disconnected.
1
2
From the Bluetooth device list on your device, select “*******
Yamaha” (*******: model name of the unit).
Turn on the Bluetooth function on your device.
41
En
Playback of Bluetooth® device contents
Connect a paired Bluetooth device and start playback. Check the following
beforehand:
• Pairing has been completed.
• Bluetooth function on the Bluetooth device is turned on.
1
Operate the Bluetooth device to establish a Bluetooth connection.
Select the model name of the unit from the Bluetooth device list on your
device.
When a connection is established, the unit’s input source automatically
switches to “Bluetooth”.
Note
▪ If you do not want the input source to switch automatically when a connection is established, set
“Input Interlock” (p.43) to “Off” in the “Option” menu.
▪ You can operate the unit to search and connect the Bluetooth device (only the most recently
connected device). In that case, follow one of the procedures below.
– Switch the input source to “Bluetooth”.
– Press ENTER while the input source is “Bluetooth”. Otherwise, press OPTION and use the
cursor keys to select “Connect”.
▪ If you cannot connect the device, please perform pairing again.
2
Operate the Bluetooth device to play back music.
Note
You cannot operate the unit to select or play back music, or display informations such as song
names.
Disconnecting a Bluetooth® connection
Follow one of the procedures below to disconnect a Bluetooth connection.
• Perform the disconnect operation on the Bluetooth device.
• Press ENTER.
• Press OPTION and use the cursor keys to select “Disconnect”.
• Switch the unit's input source to other than “Bluetooth”.
42
En
Configuring playback settings for different playback sources (Option menu)
You can configure separate playback settings for different playback sources. This
menu is available on the front panel (or on the TV screen), allowing you to easily
configure settings during playback.
1
Option menu items
Note
▪ Available items vary depending on the selected input source.
Press OPTION.
▪ Text in parentheses denotes indicators on the front display.
ENHANCER STEREO TUNED
CHARGE
OUT
▪ Default settings are underlined.
SLEEP MUTE
VOL.
ECO
Input Select
ADAPTIVE DRC VIRTUAL
Front display
Option
Input Select
Item
Function
Input Select (Input Select)
Switches the input source.
p.44
Tone Control (Tone Control)
Adjusts the level of high-frequency range and lowfrequency range individually.
p.44
Program (PRG)
Select the sound programs and stereo playback.
p.32
Sur.Decode
(SrDec)
Select which surround decoder is used when
Sur.Decode is selected as the program.
p.34
Adjusts the sound field effect level.
p.44
Sets whether the dynamic range (from maximum to
minimum) is automatically adjusted when the volume
is adjusted.
p.44
Enables/disables Compressed Music Enhancer.
p.44
Tone Control
DSP/Surround
Volume Trim
Lipsync
Signal Info.
Audio In
RETURN
DSP Level
DSP/Surround
(DSP Level)
(DSP/
Surround)
Adaptive DRC
(A.DRC)
Back
TV screen
2
Enhancer
(Enhancer)
Use the cursor keys to select an item and press ENTER.
Input Trim
Corrects volume differences between input sources.
(In.Trim)
Volume Trim
(Volume Trim) Subwoofer Trim
Fine-adjusts the subwoofer volume.
(SW.Trim)
Note
To return to the previous screen during menu operations, press RETURN.
3
4
Use the cursor keys (e/r) to select a setting.
To exit from the menu, press OPTION.
p.45
p.45
Lipsync (Lipsync)
Enables/disables the “Lipsync” setting in the “Setup”
menu.
p.45
Signal Info. (Signal Info.)
Displays information about the video/audio signal.
p.45
Audio In (Audio In)
Combines the video jack of the selected input source
with an audio jack of others.
p.45
Video Out (Video Out)
Selects a video to be output with radio sounds.
p.46
FM Mode (FM Mode)
Switches between “Stereo” and “Mono” for FM radio
reception.
p.36
Automatically registers FM radio stations with strong
signals as presets.
p.37
Clear radio stations registered to preset numbers.
p.39
Preset (Preset)
Auto Preset
Clear Preset
Traffic Program
(TrafficProgram)
43
Page
En
(U.K. and Europe models only)
Automatically searches for a traffic information
station.
p.40
Item
Function
Pairing (Pairing)
Performs a pairing operation between the unit and
your Bluetooth device.
p.41
Connect/Disconnect (Connect/
Disconnect)
Connects/disconnects the Bluetooth device.
p.42
Input Interlock (Interlock)
Sets whether the input source automatically switches
to "Bluetooth" when a Bluetooth connection is
established.
p.42
n DSP/Surround (DSP/Surround)
Page
Configures the sound field program and surround settings.
DSP Level (DSP Level)
Adjusts the sound field effect level.
Setting range
-6 dB to 0 dB to +3 dB (1 dB increments)
n Input Select (Input Select)
Adaptive DRC (A.DRC)
Switches the input source. Press ENTER to switch to the selected input source.
Choices
HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, Bluetooth, AUX
Sets whether the dynamic range (from maximum to minimum) is automatically
adjusted when the volume level is adjusted. When it is set to “On”, it is useful for
listening to playback at a low volume at night.
n Tone Control (Tone Control)
Settings
Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass)
individually.
Choices
On (On)
Automatically adjusts the dynamic range.
Off (Off)
The dynamic range is not automatically adjusted.
If “On” is selected, the dynamic range becomes narrow at a low volume and wide
at a high volume.
Treble (Treble), Bass (Bass)
Setting range
Enhancer (Enhancer)
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
Enables/disables Compressed Music Enhancer (p.35).
Note
▪ When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears.
Note
▪ You can also adjust the tone with the front panel controls. Press TONE CONTROL to select “Treble” or
“Bass”, then press PROGRAM to make an adjustment.
▪ This setting is applied separately to each input source.
▪ You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer
(p.35).
▪ If you set an extreme value, sounds may not match those from other channels.
Settings
Off (Off)
Disables Compressed Music Enhancer.
On (On)
Enables Compressed Music Enhancer.
Default
Bluetooth, TUNER: On (On)
Others: Off (Off)
44
En
n Volume Trim (Volume Trim)
n Signal Info. (Signal Info.)
Fine-adjusts volume difference between input sources or subwoofer volume.
Displays information about the video/audio signal.
Choices
Input Trim (In.Trim)
Corrects volume differences between input sources. If you are bothered by volume
differences when switching between input sources, use this function to correct it.
Format (FORMAT)
The number of source channels in the input signal (front/surround/LFE)
Channel (CHANNEL)
Note
This setting is applied separately to each input source.
Audio format of the input signal
For example, “3/2/0.1” means 3 front channels, 2 surround channels, and
LFE.
Sampling (SAMPLING) The number of samples per second of the input digital signal
Setting range
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
Subwoofer Trim (SW.Trim)
Bitrate (BITRATE)
The amount of data per second of the input bitstream signal
Video In (VIDEO IN)
Type and resolution of the input digital signal
Video Out
(VIDEO OUT)
Type and resolution of the output digital signal
Note
Fine-adjusts the subwoofer volume.
To switch the information on the front display, press the cursor keys (q/w) repeatedly.
Setting range
n Audio In (Audio In)
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
n Lipsync (Lipsync)
Combines the video jack of the selected input source with an audio jack of others. For
example, use this function in the following cases.
Enables/disables the adjustment configured in “Lipsync” (p.55) in the “Setup” menu.
• Connecting a playback device that supports HDMI video output, but not HDMI
audio output
Note
This setting is applied separately to each input source.
Input sources
Settings
HDMI 1-4, AUDIO 1-2, AV 1-3
Off (Off)
Disables the “Lipsync” adjustment.
On (On)
Enables the “Lipsync” adjustment.
Setup procedure
See “Changing the combination of video/audio input jacks” (p.21).
45
En
n Video Out (Video Out)
Selects a video to be output with the selected audio source. For example, you can
watch the video while listening to the radio.
Input sources
AUDIO, TUNER, Bluetooth, AUX
Settings
Off (Off)
Does not output video.
HDMI 1-4, AV 1-3
Outputs video input through the corresponding video input jacks.
46
En
CONFIGURATIONS
Configuring various functions (Setup Menu)
You can configure the unit’s various function with the menu displayed on the TV
screen.
Note
Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out
operations while viewing the front display.
1
2
Press SETUP.
Use the cursor keys to select a menu and press ENTER.
Setup
Speaker
HDMI
Sound
ECO
Function
Language
RETURN
3
Back
Use the cursor keys to select an item and press ENTER.
Speaker
Configuration
Distance
Level
Equalizer
Test Tone
Note
To return to the previous screen during menu operations, press RETURN.
4
5
Use the cursor keys (e/r) to select a setting and press ENTER.
To exit from the menu, press SETUP.
47
En
Setup menu items
Menu
Item
Configuration
Speaker
Function
Selects whether or not a subwoofer is connected.
Front
Selects the size of the front speakers.
p.50
Center
Selects whether or not a center speaker is connected and its size.
p.50
p.51
Surround
Selects whether or not surround speakers are connected and their size.
Sets the lower limit of the low-frequency component that can be output from speakers whose size is set to “Small”.
p.51
Subwoofer Phase
Sets the phase of the subwoofer.
p.51
Extra Bass
Enables/disables Extra Bass.
p.51
Virtual CINEMA FRONT
Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT) configuration.
p.51
Sets the distance between each speaker and listening position.
p.51
Level
Adjusts the volume of each speaker.
p.52
Equalizer
Adjusts the tone with an equalizer.
p.52
Test Tone
Enables/disables the test tone output.
p.52
HDMI Control
Enables/disables HDMI Control.
p.53
Audio Output
Selects a device to output audio.
p.53
TV Audio Input
Selects an audio input jack of the unit to be used for TV audio input.
p.53
Standby Sync
Selects whether to use HDMI control to link the standby behavior of the TV and the unit.
p.54
ARC
Enables/disables ARC.
p.54
SCENE
Enables/disables SCENE link playback.
p.54
Panorama
Enables/disables the broadening effect of the front sound field.
p.55
Center Width
Adjusts the broadening effect of the center sound field.
p.55
Dimension
Adjusts the difference in level between the front and surround sound fields.
p.55
Center Image
Adjusts the center orientation level (broadening effect) of the front sound field.
p.55
Select
Selects the method to adjust the delay between video and audio output.
p.55
Adjustment
Adjusts the delay between video and audio output manually.
p.56
Dialogue Level
Adjusts the volume of dialogue sounds.
p.56
Scale
Switches the scale of the volume display.
p.56
Dynamic Range
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback.
p.56
Max Volume
Sets the limit value of the volume.
p.56
Initial Volume
Sets the initial volume for when this receiver is turned on.
p.56
DSP Parameter
Sound
p.50
Crossover
Distance
HDMI
Page
Subwoofer
Lipsync
Dialogue
Volume
48
En
Menu
ECO
Function
Language
Item
Function
Auto Power Standby
Set the amount of time for the auto-standby function.
Page
p.57
ECO Mode
Enables/disables the eco mode (power saving mode).
p.57
Input Rename
Changes the input source name displayed on the front display.
p.58
Input Skip
Set which input source is skipped when operating the INPUT key.
p.59
Dimmer
Adjusts the brightness of the front display.
p.59
Memory Guard
Prevents accidental changes to the settings.
p.59
Remote Color Key
Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control.
p.60
Select an on-screen menu language.
p.60
49
En
Speaker
Configures the speaker settings manually.
Front
Note
Selects the size of the front speakers.
Default settings are underlined.
Settings
n Configuration
Select this option for small speakers.
Small
Configures the output characteristics of the speakers.
Note
Select this option for large speakers.
When you configure the speaker size, select “Large” if the woofer diameter of your speaker is 16 cm (6‑1/4”)
or larger or “Small” if it is smaller than 16 cm (6‑1/4”).
Large
“Front” is automatically set to “Large” when “Subwoofer” is set to “None”.
Selects whether or not a subwoofer is connected.
Center
Settings
Select this option when a subwoofer is connected.
Selects whether or not a center speaker is connected and its size.
The subwoofer will produce LFE (low-frequency effect) channel audio
and low-frequency components from other channels.
Settings
Select this option for small speakers.
Select this option when no subwoofer is connected.
None
The front speakers will produce all of the front channel frequency
components.
Note
Subwoofer
Use
The subwoofer will produce front channel low-frequency components
(configurable in “Crossover”).
Small
The front speakers will produce LFE (low-frequency effect) channel
audio and low-frequency components from other channels.
The subwoofer or front speakers will produce center channel lowfrequency components (configurable in “Crossover”).
Select this option for large speakers.
Large
None
50
En
The center speaker will produce all of the center channel frequency
components.
Select this option when no center speaker is connected.
The front speakers will produce center channel audio.
Surround
Extra Bass
Selects whether or not surround speakers are connected and their sizes.
Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy
enhanced bass sounds, regardless of the size of the front speakers and the
presence or absence of the subwoofer.
Settings
Select this option for small speakers.
Small
Large
Settings
The subwoofer or front speakers will produce surround channel lowfrequency components (configurable in “Crossover”).
Off
Disables Extra Bass.
Select this option for large speakers.
On
Enables Extra Bass.
The surround speakers will produce all of the surround channel
frequency components.
Note
You can also use BASS on the remote control to enable/disable Extra Bass (p.35).
Select this option when no surround speakers are connected.
None
The front speakers will produce surround channel audio. Virtual
CINEMA DSP works when you select a sound program.
Virtual CINEMA FRONT
Selects whether to use the front 5-channel speaker (Virtual CINEMA FRONT)
configuration.
Crossover
Settings
Sets the lower limit of the low-frequency components that can be output from a
speaker whose size is set to “Small”. A frequency sound lower than the specified
value will be produced from the subwoofer or front speakers.
Settings
Off
Disables the front 5-channel speaker configuration.
On
Enables the front 5-channel speaker configuration.
Note
40 Hz, 60 Hz, 80 Hz, 90 Hz, 100 Hz, 110 Hz, 120 Hz, 160 Hz, 200 Hz
▪ Select “On” only when utilizing the Virtual CINEMA FRONT configuration (p.13).
Note
▪ This setting is not available when “Surround” is set to “None”.
If the volume and crossover frequency are adjustable on your subwoofer, set the volume to half and
crossover frequency to maximum.
n Distance
Subwoofer Phase
Sets the distance between each speaker and listening position so that sounds from the
speakers reach the listening position at the same time. First, select the unit of distance
from “Meter” or “Feet”.
Sets the phase of the subwoofer. When the bass sound is lacking or unclear,
switch the subwoofer phase.
Choices
Settings
Front L, Front R, Center, Surround L, Surround R, Subwoofer
Normal
Does not reverse the subwoofer phase.
Reverse
Reverses the subwoofer phase.
Setting range
0.30 m to 24.00 m (1.0 ft to 80.0 ft), 0.05 m (0.2 ft) increments
Default
Front L, Front R, Subwoofer: 3.00 m (10.0 ft)
Center: 2.60 m (8.6 ft)
Others: 2.40 m (8.0 ft)
51
En
n Manual equalizer adjustment
n Level
1
2
Adjusts the volume of each speaker.
Choices
Front L, Front R, Center, Surround L, Surround R, Subwoofer
Setting range
-10.0 dB to +10.0 dB (0.5 dB increments)
3
Default
Front L, Front R, Subwoofer: 0.0 dB
4
Adjusts the tone with an equalizer.
To exit from the menu, press SETUP.
n Test Tone
EQ Select
Enables/disables the test tone output. Test tone output helps you to adjust the speaker
balance or equalizer while confirming its effect.
Selects the type of equalizer to be used.
Settings
Off
Use the cursor keys (q/w) to select the desired band
(frequency) and the cursor keys (e/r) to adjust the gain.
-6.0 dB to +6.0 dB
n Equalizer
GEQ
Use the cursor keys (q/w) to select “Channel” and the cursor
keys (e/r) to select the desired speaker channel.
Setting range
Others: -1.0 dB
PEQ
Set “EQ Select” to “GEQ”.
Settings
Applies the parametric equalizer values obtained by the YPAO
measurement (p.25).
Off
Does not output test tones.
Select this option when you want to adjust the equalizer manually.
On
Outputs test tones automatically when you adjust the speaker balance or
equalizer.
For details, see “Manual equalizer adjustment”.
Does not use the equalizer.
Note
“PEQ” is available only when the YPAO has been performed (p.25).
52
En
HDMI
Configures the HDMI settings.
HDMI OUT (TV)
Note
Enables/disables the audio output from a TV connected to the HDMI OUT jack.
Default settings are underlined.
Settings
n HDMI Control
Off
Disables the audio output from the TV.
Enables/disables HDMI Control (p.75).
On
Enables the audio output from the TV.
Settings
Off
n TV Audio Input
Disables HDMI Control.
Selects an audio input jack of the unit to be used for TV audio input when “HDMI
Control” is set to “On”. The unit’s input source automatically switches to TV audio when
the TV input is switched to its built-in tuner.
Enables HDMI Control.
On
Configure the settings in “TV Audio Input”, “Standby Sync”, “ARC”, and
“SCENE”.
Settings
Note
AV 1–3, AUDIO 1–2
To use HDMI control, you need to perform the HDMI Control link setup (p.75) after connecting HDMI
Control-compatible devices.
Default
AV 2
n Audio Output
Note
When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an
external device because the input will be used for TV audio input.
Selects a device to output audio.
Note
This setting is available only when “HDMI Control” is set to “Off”.
Amp
Enables/disables the audio output from the speakers connected to the unit.
Settings
Off
Disables the audio output from the speakers.
On
Enables the audio output from the speakers.
53
En
n Standby Sync
n SCENE
Select whether to use HDMI control to link the standby behavior of the TV and the unit
when “HDMI Control” is set to “On”.
Enables/disable SCENE link playback when “HDMI Control” is set to “On”.
When SCENE link playback is enabled, HDMI Control-compatible devices connected
to the unit via HDMI automatically works as follows, with a scene selection.
Settings
Off
Does not set the unit to standby mode when the TV is turned off.
On
Sets the unit to standby mode when the TV is turned off.
Auto
• TV: turning on and displaying video from the playback device
• Playback device: starting playback
Choices (SCENE keys)
Sets the unit to standby mode when the TV is turned off only when the unit
is receiving TV audio or HDMI signals.
BD / DVD, TV, CD, RADIO
Settings
n ARC
Enables/disables ARC (p.19) when “HDMI Control” is set to “On”.
Settings
Off
Disables SCENE link playback for the selected SCENE key.
On
Enables SCENE link playback for the selected SCENE key.
Default
Off
Disables ARC.
BD / DVD, TV: On
On
Enables ARC.
CD, RADIO: Off
Note
You do not need to change this setting normally. In case noises are produced from the speakers connected
to the unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off”
and use the TV’s speakers.
54
Note
SCENE link playback may not work properly due to the compatibility between devices. We recommend using
TV and playback devices from the same manufacturer so that HDMI Control works more effectively.
En
Sound
Configures the audio output settings.
Center Image
Note
n DSP Parameter
Adjusts the center orientation level (broadening effect) of the front sound field.
Higher to strengthen the center orientation level (less broadening effect) and lower
to weaken (more broadening effect). This setting is effective when “Neo:6 Music”
is selected.
Configures the surround decoder settings.
Setting range
Default settings are underlined.
0.0 to 0.3 to 1.0
Panorama
Enables/disables the broadening effect of the front sound field. When this function
is enabled, you can wrap front left/right channel sounds around the field and
generate a spacious sound field in combination with the surround sound field. This
setting is effective when “bPLII Music” is selected.
Settings
Off
Disables the broadening effect of the front sound field.
On
Enables the broadening effect of the front sound field.
n Lipsync
Adjusts the delay between video and audio output.
Note
You can enable/disable the Lipsync function by input sources in “Lipsync (Lipsync)” (p.45) in the “Option”
menu.
Select
Selects the method to adjust the delay between video and audio output.
Center Width
Setting range
Adjusts the broadening effect of the center sound field. Higher to enhance the
broadening effect, and lower to reduce it (closer to center). This setting is effective
when “bPLII Music” is selected.
Manual
Adjust the audio output timing in “Adjustment”.
Setting range
0 to 3 to 7
Auto
Dimension
Adjusts the delay between video and audio output automatically when
a TV that supports an automatic lipsync function is connected to the
unit via HDMI.
If necessary, you can fine-adjust the audio output timing in
“Adjustment”.
Adjusts the difference in level between the front and surround sound fields. Higher
to strengthen the front sound field and lower to strengthen the surround sound
field. This setting is effective when “bPLII Music” is selected.
Note
“Select” is automatically set to “Manual” depending on the TV connected to the unit.
Setting range
-3 to 0 to +3
55
Select this option when you want to adjust the delay between video
and audio output manually.
En
Adjustment
Dynamic Range
Adjusts the delay between video and audio output manually when “Select” is set to
“Manual”. You can fine-adjust the audio output timing when “Select” is set to
“Auto”.
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital
and DTS signals) playback.
Settings
Setting range
0 ms to 500 ms (1 ms increments)
n Dialogue
Maximum
Produces audio without adjusting the dynamic range.
Standard
Optimizes the dynamic range for regular home use.
Min/Auto
Adjusts the volume of dialogue sounds.
Dialogue Level
Sets the dynamic range for clear sound even at night or at low
volumes.
When playing back Dolby TrueHD signals, the dynamic range is
automatically adjusted based on the input signal information.
Max Volume
Adjusts the volume of the center orientation sounds such as dialogue.
Sets the limit value of the volume.
Setting range
Setting range
0 to 3 (higher to strengthen)
-30.0 dB to +15.0 dB (5.0 dB increments), +16.5 dB [50.0 to 95.0 (5.0 increments),
97.0]
n Volume
Initial Volume
Configures the volume settings.
Sets the initial volume when the receiver is turned on.
Scale
Settings
Switches the scale of the volume display.
Settings
Off
Sets the level to the volume level of the unit when it last entered
standby mode.
Sets the unit to mute the audio output.
dB
Displays the volume in the “dB” unit.
Mute
0-97
Displays the volume in the numeric value (0.5 to 97.0).
-80.0 dB to +16.5 dB
(0.5 dB increments)
Sets the level to the specified volume level.
[0.5 to 97.0
(0.5 increments)]
56
En
ECO
Configures the power supply settings.
Note
Default settings are underlined.
n Auto Power Standby
Set the amount of time for the auto-standby function.
Settings
Off
Does not set the unit to standby mode automatically.
20 minutes
Sets the unit to standby mode when you have not operated the unit and
the unit has not detected any input signal for the specified time.
2 hours, 4 hours,
8 hours, 12 hours
Sets the unit to standby mode when you have not operated the unit for the
specified time.
Default
U.K. and Europe models: 20 minutes
Other models: Off
Note
Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front
display.
n ECO Mode
You can reduce the unit’s power consumption by setting the eco mode to “On”. After
setting, be sure to press ENTER to restart the unit.
When the eco mode is enabled, you can reduce the unit’s power consumption.
Settings
Off
Disables the eco mode.
On
Enables the eco mode.
Note
▪ When “ECO Mode” is set to “On”, the front panel display may become dark.
▪ If you want to play audio at high volume, set “ECO Mode” to “Off”.
57
En
Function
Configures the functions that make the unit easier to use.
Procedure to rename manually
Note
Default settings are underlined.
1
n Input Rename
2
Changes the input source name displayed on the front display. You can also select a
name from the presets or a name created by the Auto Rename function.
Use the cursor keys (q/w) to select an input source to be
renamed.
Use the cursor keys (e/r) to select “Manual” and press
ENTER.
Input sources
Note
HDMI 1-4, AUDIO 1-2, AV 1-3, Bluetooth, AUX
To select the preset name, use the cursor keys (e/r).
Default
3
HDMI 1-4: Auto
Others: Manual (For Bluetooth, AUX only “Manual” can be selected.)
The edit screen is displayed.
4
Procedure to rename automatically
1
2
Use the cursor keys (q/w) to select an input source to be
renamed.
To cancel the entry, select “CANCEL”.
5
6
Use the cursor keys (e/r) to select “Auto”.
To check a created name, press ENTER.
Note
During selecting “Auto”, the created name is saved even after the device connection is
terminated. To reset to the default setting, switch the setting to “Manual” at once and then set
it again to “Auto”.
4
5
Use the cursor keys and ENTER key to edit the name, and then
select “OK” to confirm the new name.
Note
The unit creates a name automatically according to the connected
device.
3
Press ENTER.
To change another input source name, repeat steps 1 to 3.
To exit from the menu, press SETUP.
58
En
To change another input source name, repeat steps 1 to 4.
To exit from the menu, press SETUP.
n Input Skip
n Dimmer
Set which input source is skipped when operating the INPUT key.
Adjusts the brightness of the front display.
You can select the desired input source quickly by using this function.
Setting range
Input sources
-4 to 0 (higher to brighten)
HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, Bluetooth, AUX
Note
Settings
The front display may become dark when “ECO Mode” (p.57) is set to “On”.
Off
Does not skip the selected input source.
On
Skips the selected input source.
n Memory Guard
Prevents accidental changes to the settings.
Settings
Off
Does not protect the settings.
On
Protects the settings until “Off” is selected.
Note
When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen.
59
En
n Remote Color Key
Language
Set the unit's functions for the RED/GREEN/YELLOW/BLUE key of the remote control.
Select an on-screen menu language.
Settings
Default
Note
Default settings are underlined.
Assigns the functions of playback devices connected to the unit with an
HDMI cable.
Settings
Assigns the unit's input sources to each key. The assigned input sources
can be set separately.
Input
Input sources
HDMI 1-4, AUDIO 1-2, AV 1-3, TUNER, Bluetooth, AUX
Default
RED: HDMI2, GREEN: HDMI4, YELLOW: AV 2, BLUE: AUX
Assigns the functions of sound mode to each key.
RED: MOVIE
GREEN: MUSIC
Program
YELLOW: STEREO
English
English
日本語
Japanese
Français
French
Deutsch
German
Español
Spanish
Русский
Russian
Italiano
Italian
中文
Chinese
BLUE: SUR.DECODE
Note
For example, if you press the RED key repeatedly, you can select your
favorite sound program from the sound programs (MOVIE) (p.32) suitable
for the video source.
The information on the front display is provided in English only.
60
En
Configuring the system settings (ADVANCED SETUP menu)
Configure the system settings of the unit while viewing the front display.
1
2
ADVANCED SETUP menu items
Set the unit to standby mode.
Note
Default settings are underlined.
While holding down STRAIGHT on the front panel, press
z (power).
Item
SP IMP.
z (power)
REMOTE ID
3
4
5
STRAIGHT
Press PROGRAM to select an item.
Page
(U.S.A. and Canada models only)
Changes the speaker impedance setting.
Selects the unit’s remote control ID.
(Asia, Taiwan and General models only)
TU
PROGRAM
Function
Changes the FM/AM tuning frequency setting.
p.61
p.62
p.62
TV FORMAT
Switches the video signal type of HDMI output.
p.62
4K MODE
Selects the HDMI 4K signal format.
p.62
INIT
Restores the default settings.
p.63
VERSION
Checks the version of firmware currently installed on the unit.
p.63
Press STRAIGHT to select a setting.
Changing the speaker impedance setting (SP IMP.)
Press z (power) to set the unit to standby mode and turn it on
again.
(U.S.A. and Canada models only)
CHARGE
OUT
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
ECO
SP IMP.••8¬MIN
The new settings take effect.
ADAPTIVE DRC VIRTUAL
Change the unit’s speaker impedance settings depending on the impedance of the
speakers connected.
Settings
61
6 Ω MIN
Select this option when you connect 6-ohm speakers to the unit.
8 Ω MIN
Select this option when you connect 8-ohm or higher speakers to the unit.
En
Selecting the remote control ID (REMOTE ID)
ENHANCER STEREO TUNED
CHARGE
OUT
Switching the video signal type (TV FORMAT)
SLEEP MUTE
CHARGE
OUT
VOL.
ECO
REMOTE ID••ID1
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
ECO
ADAPTIVE DRC VIRTUAL
TV FORMAT•NTSC
Change the unit’s remote control ID so that it matches the remote control’s ID (default:
ID1). When using multiple Yamaha AV receivers, you can set each remote control with
a unique remote control ID for its corresponding receiver.
ADAPTIVE DRC VIRTUAL
Switch the video signal type of HDMI output so that it matches to the format of your TV.
Settings
Since the unit automatically selects the video signal type so that it matches to the TV, it
is unnecessary to change the setting normally. Change the setting only when images
on the TV screen do not appear correctly.
ID1, ID2
Settings
NTSC, PAL
n Changing the remote control ID of the remote control
1
Default
U.S.A., Canada, Korea, Taiwan and General models: NTSC
To select ID1, while holding down the cursor key (e), hold down
SCENE (BD/DVD) for more than 3 seconds.
To select ID2, while holding down the cursor key (e), hold down
SCENE (TV) for more than 3 seconds.
Other models: PAL
Selecting the HDMI 4K signal format (4K MODE)
Changing the FM/AM tuning frequency setting (TU)
4K MODE•MODE 2
Selects the format of signals input/output at the unit when HDMI 4K (60 Hz/50 Hz)
compatible TV and playback device are connected to the unit.
(Asia, Taiwan and General models only)
CHARGE
OUT
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
ECO
TU••••FM50/AM9
Settings
ADAPTIVE DRC VIRTUAL
Change the FM/AM tuning frequency setting of the unit depending on your country or
region.
MODE 1
Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:4:4, 4:2:2 or 4:2:0 format.
Depending on the connected device or HDMI cables, video may not be
displayed correctly. In this case, select “MODE 2”.
Settings
MODE 2
Inputs/outputs 4K (60 Hz/50 Hz) signals in 4:2:0 format.
FM100/AM10
Select this when you want to adjust the FM frequency by 100-kHz steps
and AM by 10-kHz steps.
FM50/AM9
Select this when you want to adjust the FM frequency by 50-kHz steps
and AM by 9-kHz steps.
Note
When “MODE 1” is selected, use a high-speed HDMI cable that supports 18 Gbps.
62
En
Restoring the default settings (INIT)
CHARGE
OUT
ENHANCER STEREO TUNED
Checking the firmware version (VERSION)
SLEEP MUTE
CHARGE
OUT
VOL.
ECO
INIT••••CANCEL
ENHANCER STEREO TUNED
SLEEP MUTE
VOL.
ECO
ADAPTIVE DRC VIRTUAL
VERSION••xx.xx
ADAPTIVE DRC VIRTUAL
Restores the default settings for the unit.
Check the version of firmware currently installed on the unit.
Choices
Note
ALL
Restores the default settings for the unit.
CANCEL
Does not perform an initialization.
It may take a while until the firmware version is displayed.
63
En
APPENDIX
Frequently asked questions
The frequently asked questions from customers and the answers are shown below.
I want to prevent accidental changes to the settings...
The new speaker system does not provide an ideal sound balance...
You can protect the settings configured on the unit (such as speaker settings) by
utilizing “Memory Guard” in the “Setup” menu (p.59).
If you have changed speakers or have a new speaker system, use YPAO to optimize
the speaker settings again (p.25). If you want to adjust the speaker settings manually,
use “Speaker” in the “Setup” menu (p.50).
The unit’s remote control is simultaneously controlling another Yamaha
product as well as the unit...
When using multiple Yamaha products, the remote control may work on another
Yamaha product or another remote control may work on the unit. If this happens,
register different remote control IDs for the devices that you want to control with each
remote control (p.62).
We want to set limitations on the volume control...
If someone accidentally operates the controls on the main unit or remote control, the
volume may suddenly increase. This may also cause injury or damage the unit or
speakers. We recommend using “Max Volume” in the “Setup” menu to set the
maximum volume level for the unit in advance (p.56).
The combination of video/audio input jacks does not match an external
device...
I want to fix the volume when turning on the unit...
Use “Audio In” in the “Option” menu to change the combination of video/audio input
jacks so that it matches the output jack(s) of your external device (p.21).
By default, the volume level when the unit last entered standby mode is automatically
applied. If you want to fix the volume, use “Initial Volume” in the “Setup” menu to set
the volume to be applied when the receiver is turned on (p.56).
Video and audio are not synchronized...
Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output
(p.55).
The volume varies depending on the input sources...
You can correct volume differences between input sources by utilizing “Input Trim” in
the “Option” menu (p.45).
I want to hear audio from the TV speakers...
Use “Audio Output” in the “Setup” menu to select the output destination of signals
input into the unit (p.53). Your TV speakers may be selected as an output destination.
HDMI Control does not work at all...
To use HDMI Control, you need to perform the HDMI Control link setup (p.75). After
connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit,
enable HDMI Control on each device and perform the HDMI Control link setup. This
setup is required every time you add a new HDMI Control-compatible device to your
system. For information on how HDMI Control works between your TV and playback
devices, refer to the instruction manuals for each device.
I want to change the on-screen menu language...
Use “Language” in the “Setup” menu to select a language from English, Japanese,
French, German, Spanish, Russian, Italian and Chinese (p.24).
I want to change the input source name...
By default, input source names (such as “HDMI1” and “AV 1”) are displayed on the
front display when an input source is selected. If you want to rename them as you like,
use “Input Rename” (p.58) in the “Setup” menu. You can also select a name from the
presets (such as “Blu-ray” and “DVD”).
64
En
Troubleshooting
Refer to the table below when the unit does not function properly.
If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
First, check the following:
1
2
3
The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely.
The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on.
The connectors of each cable are securely inserted in to jacks on each device.
Power, system and remote control
Problem
Cause
Remedy
The power does not turn on.
The protection circuitry has been activated three times
consecutively.
As a safety precaution, capability to turn on the power is disabled. Contact your
nearest Yamaha dealer or service center to request repair.
The power does not turn off.
The internal microcomputer has frozen, due to an external electric Hold down z (power) on the front panel for more than 15 seconds to reboot the
shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet
in the power supply voltage.
and plug it again.)
The power turns off (standby mode) immediately. The unit was turned on while a speaker cable was shorted.
The sleep timer worked.
The unit enters standby mode automatically.
The unit is not reacting.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and
speakers (p.17).
Turn on the unit and start playback again.
The auto-standby function activated because the unit was not used To disable the auto-standby function, set “Auto Power Standby” in the “Setup”
for the specified time.
menu to “Off” (p.57).
The speaker impedance setting is incorrect.
Set the speaker impedance to match your speakers (p.61).
The protection circuitry has been activated because of a short
circuit.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and
speakers (p.17).
Hold down z (power) on the front panel for more than 15 seconds to reboot the
The internal microcomputer is frozen, due to an external electric
shock (such as lightning or excessive static electricity) or to a drop unit. (If the problem persists, disconnect the power cable from the AC wall outlet
in the power supply voltage.
and plug it again.)
65
En
Problem
The unit cannot be controlled using the remote
control.
Cannot select the desired input source even if
“INPUT” is pressed.
The RED/GREEN/YELLOW/BLUE keys of the
remote control do not operate.
Cause
Remedy
The unit is out of the operating range.
Use the remote control within the operating range (p.4).
The batteries are weak.
Replace with new batteries.
The unit’s remote control sensor is exposed to direct sunlight or
strong lighting.
Adjust the lighting angle, or reposition the unit.
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.62).
The function which skips some input sources is set.
Set “Input Skip” of the desired input source in the “Setup” menu to “Off” (p.59).
The device which is connected to the unit via HDMI does not
support the operation of the RED/GREEN/YELLOW/BLUE keys.
Use a device which supports the operation of the RED/GREEN/YELLOW/BLUE
keys.
The settings of the RED/GREEN/YELLOW/BLUE keys of the unit's
remote control have been changed.
Set the “Remote Color Key” settings in the “Setup” menu to “Default” (p.60).
Audio
Problem
No sound.
The volume cannot be increased.
No sound is coming from a specific speaker.
Cause
Remedy
Another input source is selected.
Select an appropriate input source with the input selection keys.
Signals that the unit cannot reproduce are being input.
Some digital audio formats cannot be played back on the unit. To check the
audio format of the input signal, use “Signal Info.” in the “Option” menu (p.45).
The cable connecting the unit and playback device is defective.
If there is no problem with the connection, replace with another cable.
The maximum volume is set.
Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.56).
A device connected to the output jacks of the unit is not turned on. Turn on all devices connected to the output jacks of the unit.
The playback source does not contain a signal for the channel.
To check it, use “Signal Info.” in the “Option” menu (p.45).
The currently selected sound program/decoder does not use the
speaker.
To check it, select “5ch Stereo” (p.31).
Audio output of the speaker is disabled.
Perform YPAO (p.25) or use “Configuration” in the “Setup” menu to change the
speaker settings (p.50).
The volume of the speaker is set too low.
Perform YPAO (p.25) or use “Level” in the “Setup” menu to adjust the speaker
volume (p.52).
The speaker cable connecting the unit and the speaker is
defective.
If there is no problem with the connection, replace with another speaker cable.
The speaker is malfunctioning.
To check it, replace with another speaker. If the problem persists, the unit may be
malfunctioning.
66
En
Problem
Cause
Remedy
The playback source does not contain Low Frequency Effect (LFE) To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the
or low-frequency signals.
front channel low-frequency components from the subwoofer (p.51).
No sound is coming from the subwoofer.
Subwoofer output is disabled.
Perform YPAO (p.25) or set “Subwoofer” in the “Setup” menu to “Use” (p.50).
The volume of the subwoofer is too low.
Adjust the volume on the subwoofer.
The subwoofer has been turned off by its auto-standby function.
Disable the auto-standby function of the subwoofer or adjust its sensitivity level.
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
No sound from the playback device (connected to The unit is set not to output audio input through HDMI jacks from
the unit with HDMI).
the SPEAKERS terminals.
No sound from the TV (when HDMI Control is
used).
In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.53).
The number of devices connected to the HDMI OUT jack exceeds
the limit.
Disconnect some of the HDMI devices.
The TV is set to output audio from the TV speakers.
Change the audio output setting on your TV so that the TV audio is output from
the speakers connected to the unit.
A TV that does not support ARC is connected to the unit only with
an HDMI cable.
Use a digital optical cable to make an audio connection (p.19).
(If the TV is connected to the unit with an audio cable)
The TV audio input setting does not match the actual connection.
(If you are trying to use ARC)
Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack
(p.53).
Set “ARC” in the “Setup” menu to “On” (p.54). Also, enable ARC on the TV.
ARC is disabled on the unit or TV.
When playing back DSD audio, the unit disables
the audio output from a TV.
The unit does not support DSD audio output from a TV.
Change the audio output setting on the playback device to PCM.
Only the front speakers work on multichannel
audio.
The playback device is set to output 2-channel audio (such as
PCM) only.
To check it, use “Signal Info.” in the “Option” menu (p.45). If necessary, change
the digital audio output setting on the playback device.
Noise/hum is heard.
The sound is distorted.
The unit is too close to another digital or radio frequency device.
Move the unit further away from the device.
The cable connecting the unit and playback device is defective.
If there is no problem with the connection, replace with another cable.
The volume of the unit is too high.
Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to
“Off” (p.57).
A device connected to the unit’s output jacks is not turned on.
Turn on all devices connected to the unit’s output jacks.
67
En
Video
Problem
No video.
No video from the playback device (connected to
the unit with HDMI).
No image (contents required the HDCP 2.2 compatible HDMI device) from the playback
device connected to the unit with HDMI.
The menu of the unit is not displayed on the TV.
Cause
Remedy
Another input source is selected on the unit.
Select an appropriate input source with the input selection keys.
Another input source is selected on the TV.
Switch the TV input to display the video from the unit.
The video signal output from the unit is not supported by the TV.
Check the video output setting of the playback device. For information about
video signals supported by the TV, refer to the instruction manuals for the TV.
The cable connecting the unit and TV (or playback device) is
defective.
If there is no problem with the connection, replace with another cable.
The input video signal (resolution) is not supported by the unit.
To check the information about the current video signal (resolution), use “Signal
Info.” in the “Option” menu (p.45). For information about video signals supported
by the unit, see “HDMI signal compatibility” (p.77).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The number of devices connected to the HDMI OUT jack is over
the limit.
Disconnect some of the HDMI devices.
The TV (HDMI input jack) does not support HDCP 2.2. (The
Warning message can be displayed on the TV screen.)
Connect the unit to the TV (HDMI input jack) that supports HDCP 2.2.
The TV is not connected to the unit via HDMI.
You can display the menu of the unit on the TV only when they are connected
with an HDMI cable. If necessary, use an HDMI cable to connect them (p.19 to
p.20).
Another input source is selected on the TV.
Switch the TV input to display the video from the unit (HDMI OUT jack).
68
En
FM/AM radio
Problem
FM radio reception is weak or noisy.
Cause
Remedy
There is multi-path interference.
Adjust the FM antenna height or orientation, or place it in a different location.
Your area is too far from the FM station transmitter.
To select monaural FM radio reception “FM Mode” in the “Option” menu to
“Mono” (p.36).
The noises may be caused by fluorescent lamps, motors,
thermostats, or other electrical equipment.
It is difficult to completely eliminate noise. It may be reduced by using an outdoor
AM antenna.
Use an outdoor FM antenna.
AM radio reception is weak or noisy.
Select the station manually (p.36).
Your area is too far from the FM station transmitter.
Use an outdoor antenna. We recommend using a sensitive multi-element
antenna.
Adjust the AM antenna orientation.
Radio stations cannot be selected automatically.
Select the station manually (p.36).
The AM radio signal is weak.
AM radio stations cannot be registered as
presets.
Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with
the supplied AM antenna.
Auto Preset is for registering FM radio stations only. Register AM radio stations
manually (p.37).
Auto Preset has been used.
69
En
Bluetooth®
Problem
Cannot make the unit pair with a Bluetooth
device.
Cause
Remedy
Another Bluetooth device is connected.
Terminate current Bluetooth connection, and perform pairing with the new device.
This unit and the device are too far apart.
Move the device closer to this unit.
There is a device (microwave oven, wireless LAN, etc.) that outputs
Move this unit away from the device that is emitting radio-frequency signals.
signals in the 2.4 GHz frequency band nearby.
The Bluetooth device does not support A2DP.
Perform pairing with a device which supports A2DP.
Another Bluetooth device is connected.
Terminate current Bluetooth connection, then establish a Bluetooth connection
with that device again.
The Bluetooth function of the device is turned off.
Turn on the Bluetooth function of the device.
Delete the pairing information of the device, and then perform pairing again
(p.41).
Cannot make a Bluetooth connection.
The pairing information has been deleted.
This unit can be paired with eight devices. If pairing with a ninth device is
performed, the pairing information with the earliest connection date will be
deleted.
This unit is not registered on the device’s Bluetooth connection list. Perform paring again (p.41).
The volume of the connecting device is set too low.
Turn up the volume of the connecting device.
The connecting device is not set to send Bluetooth audio signals to
Switch the output of Bluetooth audio signals of the connecting device to the unit.
the unit.
No sound is produced, or the sound is
interrupted during playback.
The Bluetooth connection of the unit with the device has
terminated.
Perform Bluetooth connection operations again (p.42).
There is a device (microwave oven, wireless LAN, etc.) that outputs
Move this unit away from the device that is emitting radio-frequency signals.
signals in the 2.4 GHz frequency band nearby.
This unit and the connecting device are too far apart.
70
En
Move the connecting device closer to this unit.
Error indications on the front display
Refer to the table below when the error message is indicated on the front display.
Message
Cause
Remedy
Check SP Wires
The speaker cables short circuit.
Twist the bare wires of the cables firmly and connect to the unit and speakers properly.
Internal Error
An internal error has occurred.
Contact the nearest authorized Yamaha dealer or service center.
Not found
The Bluetooth device is not found.
RemID Mismatch
The remote control IDs of the unit and the remote control are not
identical.
• Place the Bluetooth device within 10 m (32 ft) of the Bluetooth receiver.
• Perform pairing again.
Change the remote control ID of the unit or the remote control (p.62).
71
En
Glossary
This is a glossary of the technical terms used in this manual.
DTS-HD Master Audio
Audio information
DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition
home theater experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio
can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)
simultaneously. This technology is used for audio on BD (Blu-ray Disc).
n Audio decoding format
DTS Neo: 6
DTS Neo: 6 enables 6-channel playback from 2-channel sources. There are two modes available:
“Music mode” for music sources and “Cinema mode” for movie sources. This technology provides
discrete full-bandwidth matrix channels of surround sound.
Dolby Digital
Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that
supports 5.1-channel audio. This technology is used for audio on most DVD disc.
DSD (Direct Stream Digital)
Dolby Pro Logic II
Dolby Pro Logic II enables 5-channel playback from 2-channel sources. There are three modes
available: “Music mode” for music sources, “Movie mode” for movie sources, and “Game mode”
for game sources.
DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as
SACD (Super Audio CDs). The signals are stored at a high-frequency sampling rate of 2.8224
MHz. The highest frequency response is equal to or higher than 100 kHz, with a dynamic range of
120 dB. This technology offers better audio quality than that used for CDs.
Dolby TrueHD
MP3
Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to
offer a high-definition home theater experience with the quality of the studio master. Dolby TrueHD
can carry up to eight channels of 96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio)
simultaneously. This technology is used for audio on BD (Blu-ray Disc).
One of the compressed digital audio format used by MPEG. With psychoacoustic technologies,
this compression method achieves a high compression rate. Reportedly, it is capable of
compressing data quantity by about 1/10 maintaining a certain level of audio quality.
DTS 96/24
An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio
streaming services on Internet because it allows a high compression rate of data while
maintaining better audio quality than MP3.
DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit
audio. This format remains fully compatible with the existing multichannel audio systems that
support DTS Digital Surround. This technology is used for music DVDs, etc.
MPEG-4 AAC
PCM (Pulse Code Modulation)
DTS Digital Surround
DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports
5.1-channel audio. This technology is used for audio on most DVD discs.
PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted.
This technology is the basis of all other audio format. This technology is used as a lossless audio
format called Linear PCM for audio on a variety of media, including CDs and BD (Blu-ray Disc).
DTS-ES
Sampling frequency/Quantization bit
DTS-ES creates total 6.1-channel audio from 5.1-channel sources that are recorded with DTS-ES.
This decoder adds a surround back sound to the original 5.1-channel sound. In the DTS-ES Matrix
6.1 format, a surround back sound is recorded in the surround channels, and in the DTS-ES
Discrete 6.1 format, a discrete surround back channel is recorded.
Sampling frequency and quantization bits indicate the quantity of information when an analog
audio signal is digitized. These values are noted as in the following example: “48 kHz/24-bit”.
DTS Express
DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a
higher compression rate than the DTS Digital Surround format developed by DTS, Inc. This
technology is developed for audio streaming services on the Internet and secondary audio on BD
(Blu-ray Disc).
• Sampling frequency
Sampling frequency (the number of times the signal is sampled per second) is called the
sampling rate. When the sampling frequency is higher, the range of frequencies that can be
played back are wider.
• Quantization bit
The number of quantization bits indicate the degree of accuracy when converting the sound
level into a numeric value. When the number of quantized bits is higher, the expression of the
sound level is more accurate.
DTS-HD High Resolution Audio
WAV
DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that
supports 7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully
compatible with the existing multichannel audio systems that support DTS Digital Surround. This
technology is used for audio on most BD (Blu-ray Disc).
Windows standard audio file format, which defines the method of recording the digital data
obtained by converting audio signals. By default, the PCM method (no compression) is used, but
you can also use other compression methods.
72
En
Yamaha technologies
WMA (Windows Media Audio)
One of the compressed digital audio formats developed by Microsoft Corporation. With
psychoacoustic technologies, this compression method achieves a high compression rate.
Reportedly, it is capable of compressing data quantity by about 1/20 maintaining a certain level of
audio quality.
CINEMA DSP (Digital Sound Field Processor)
n Others
LFE (Low Frequency Effects) 0.1 channel
This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to
120 Hz. This channel is added to the channels for all bands with Dolby Digital or DTS to enhance
low frequency audio effects. This channel is labeled 0.1 because it is limited to only low frequency
audio.
Lip sync
Since the Dolby Surround and DTS systems were originally designed for use in movie theaters,
their effect is best experienced in a theater that has many speakers designed for acoustic effects.
Since home conditions (such as room size, wall material, and number of speakers) can differ so
widely, it is inevitable that there are differences in the sound that you hear. Based on a wealth of
actually measured data, CINEMA DSP, Yamaha’s original DSP technology provides the
audiovisual experience of a movie theater in your own home.
Compressed Music Enhancer
The Compressed Music Enhancer feature compensates for missing harmonics in compression
music formats (such as MP3). As a result, this technology provides improved performance for the
overall sound system.
SILENT CINEMA
Video output sometimes lags behind audio output due to the complexity of signal processing
caused by an increase in video signal capacity. Lip sync is a technique for automatically
correcting the timing lag between audio and video output.
Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones.
Parameters for headphones have been set for each sound program, so that accurate
representations of all the sound programs can be enjoyed on headphones.
Virtual CINEMA DSP
HDMI and video information
Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround
speakers with front left and right speakers. Even if the surround speakers are not connected, the
unit creates the realistic sound field in a listening room.
Composite video signal
With the composite video signal system, color, brightness, and synchronization data signals are
combined and transmitted with a single cable.
YPAO (Yamaha Parametric room Acoustic Optimizer)
Deep Color
Deep Color is a technology that HDMI specification supports. Deep Color increases the number of
available colors within the boundaries defined by the RGB or YCbCr color space. Conventional
color systems process the color using 8 bits. Deep Color processes the color with 10, 12, or 16
bits. This technology allows HDTVs and other displays to increase from millions of colors to
billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle
gradations between colors.
The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections,
measures the distances from them to your listening position(s), and then automatically optimizes
the speaker settings, such as volume balance and acoustic parameters, to suit your room.
HDMI
HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/
video signal transmission. This interface transmits both digital audio and digital video signals
using a single cable without any loss. HDMI complies with HDCP (High-bandwidth Digital Content
Protection) and provides a secure audio/video interface. For further information on HDMI, visit the
HDMI website at “http://www.hdmi.org/”.
x.v.Color
“x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color
space than sRGB and allows the expression of colors that were not hitherto possible. While
remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color
space, and thus can produce more vivid, natural images.
73
En
Supported devices
Video signal flow
The following devices can be used by the unit.
Video signals input from a video device to the unit are output to a TV as shown below.
Video device
Supported devices
The unit
TV
n Bluetooth® devices
• Bluetooth devices that support A2DP can be used.
• Yamaha does not assure the connections of all Bluetooth devices.
HDMI connection
HDMI in
HDMI
HDMI out
HDMI
HDMI
HDMI
Composite video connection
VIDEO in
VIDEO
74
En
VIDEO
VIDEO out
VIDEO
VIDEO
Information on HDMI
(Example)
The additional information on HDMI is as follows.
HDMI Control
HDMI Control
HDMI Control allows you to operate external devices via HDMI. If you connect a TV
that supports HDMI Control to the unit with an HDMI cable, you can control the unit
(such as power and volume) with TV remote control operations. You can also control
playback devices (such as HDMI Control-compatible BD/DVD players) connected to
the unit with an HDMI cable.
Playback starts
Press SCENE (BD/DVD)
Turns on and displays
video from the playback
device
To use HDMI Control, you need to perform the following HDMI Control link setup after
connecting the TV and playback devices.
n Operations available from the TV’s remote control
For details on settings and operating your TV, refer to the instruction manual for the TV.
• Standby synchronization
Note
• Volume control including mute
This setup is required every time you add a new HDMI Control-compatible device to your system.
• Switching to input audio from the TV when the TV input is switched to its built-in
tuner
1
2
• Switching to input video/audio from the selected playback device
• Switching between audio output devices (the unit or TV speaker)
(Example)
HDMI Control
HDMI Control
HDMI Control
Turn on the unit, TV, and playback devices.
Configure the settings of the unit.
1
2
Switch the TV input to display video from the unit.
Press SETUP.
SLEEP
SCENE
BD
DVD
TV
STRAIGHT
CD
RADIO
ENHANCER
BASS
MUTE
SETUP
PROGRAM
Playback device
also turns off
The unit turns off
(standby)
FM
SETUP
AM
INPUT
OPTION
VOLUME
BLUETOOTH
Turn off the TV
MUTE
SETUP
Cursor keys
ENTER
OPTION
ENTER
ENTER
n Operations available from the unit’s remote control
RETURN
TOP MENU
DISPLAY
HOME
POP-UP/MENU
RETURN
RED
GREEN
YELLOW
DISPLAYY
DISPLA
BLUE
MEMORY
TUNING
• Starting playback on the playback device and turning on the TV with a scene
selection (p.30)
TUNING
PRESET
• Switching the TV input to display the “Setup” menu (when SETUP is pressed)
• Controlling the playback device (playback and menu operations)
75
En
TOP MENU
HOME
POP-UP/MENU
3
8
Use the cursor keys to select “HDMI” and press ENTER.
Setup
Speaker
HDMI
Sound
ECO
Note
Function
Language
RETURN
4
▪ If HDMI Control does not work properly, try unplugging the TV in Step 2 and plugging in the TV again in
Step 3. It may solve the problem. Also, HDMI Control may not work if the number of connected devices
exceeds the limit. In this case, disable HDMI Control on the devices not in use.
Back
▪ If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting
on the TV.
Use the cursor keys (q/w) to select “HDMI Control” and the cursor keys
(e/r) to select “On” as shown below.
HDMI
HDMI Control
▪ If you reconnect the HDMI cable, perform the procedure 5-8 again.
▪ We recommend using TV and playback devices from the same manufacturer so that HDMI Control works
more effectively.
On
Audio Output
TV Audio Input
Standby Sync
ARC
AV2
Auto
On
SCENE
RETURN
5
6
3
4
5
6
7
Check that the unit is properly synchronized with the TV by
turning off the TV or adjusting the TV volume with the TV remote
control.
Back
If you made a digital optical cable connection between the TV and the
unit, use the cursor keys (q/w) to select “TV Audio Input” and the
cursor keys (e/r) to select “AUDIO1”.
Press SETUP.
Enable HDMI Control on the TV and playback devices (such as
HDMI Control-compatible BD/DVD players).
Turn off the main power of the TV and then turn off the unit and
playback devices.
Turn on the unit and playback devices and then turn on the TV.
Switch the TV input to display the video from the unit.
Check the followings.
On the unit: The input to which the playback device is connected is
selected. If not, select the input source manually.
On the TV: The video from the playback device is displayed.
76
En
Audio Return Channel (ARC)
HDMI signal compatibility
ARC allows you to input TV audio to the unit with the HDMI cable which transmits video
signal to the TV.
n Audio signals
Check the following after the HDMI Control settings.
1
2
Select a TV program with the TV remote control.
Check that the input source of the unit will be automatically
switched to “AV 2” and the TV audio will be played back on the
unit.
If you cannot hear the TV audio, check the following:
▪ “ARC” (p.54) in the “Setup” menu is set to “On”.
▪ The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI
jack marked “ARC”) on the TV.
Audio signal type
Audio signal format
2ch Linear PCM
2ch, 32 to 192 kHz, 16/20/24 bit
Compatible media (example)
CD, DVD-Video, DVD-Audio
Multichannel Linear PCM
8ch, 32 to 192 kHz, 16/20/24 bit
DVD-Audio, BD (Blu-ray disc),
HD DVD
DSD
2 to 5.1ch, 2.8224 MHz, 1 bit
SACD
Bitstream
Dolby Digital, DTS
DVD-Video
Bitstream
(High definition audio)
Dolby TrueHD, Dolby Digital Plus,
DTS-HD Master Audio, DTS-HD
BD (Blu-ray disc), HD DVD
High Resolution Audio, DTS
Express
n Video signals
Some HDMI jack on the TV is not compatible with ARC. For details, refer
to the instruction manual for the TV.
The unit is compatible with the video signals of the following resolutions:
Note
• VGA
• 720p/60 Hz, 50 Hz
▪ If the audio is interrupted while using ARC, set “ARC” (p.54) in the “Setup” menu to “Off” and use a digital
optical cable to input TV audio to the unit (p.19).
• 480i/60 Hz
• 1080i/60 Hz, 50 Hz
• 576i/50 Hz
• 1080p/60 Hz, 50 Hz, 24 Hz
▪ When using ARC, connect a TV with an HDMI cable that supports ARC.
• 480p/60 Hz
• 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz
▪ “AV 2” is set as TV audio input at the factory. If you have connected any external device to the AV 2 jacks,
use “TV Audio Input” (p.53) in the “Setup” menu to change the TV audio input assignment. To use the
SCENE function (p.30), you also need to change the input assignment for SCENE (TV).
• 576p/50 Hz
Note
▪ When CPPM copy-protected DVD-Audio is played back, video/audio signals may not be output,
depending on the type of the DVD player.
▪ The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For details, refer to the
instruction manual for each device.
▪ To decode audio bitstream signals on the unit, set the input source device appropriately so that the device
outputs the bitstream audio signals directly (does not decode the bitstream signals on the playback
device). For details, refer to the instruction manual for the playback device.
77
En
Trademarks
The trademarks used in this manual are as follows.
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing Limited. DTS,
DTS-HD, the Symbol, & DTS and the Symbol together are
registered trademarks of DTS, Inc. © DTS, Inc. All Rights
Reserved.
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Yamaha Corporation is under license.
App Store is a service mark of Apple Inc.
Android™ is a trademark of Google Inc.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
78
En
Specifications
The specifications of this unit are as follows.
HDMI
Input jacks
HDMI Features:
• 4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC (Audio Return Channel), HDMI
Control (CEC), Auto Lip Sync, Deep Color, “x.v.Color”, HD audio playback, 21:9 Aspect Ratio,
BT.2020 Colorimetry, HDR Compatible
Analog Audio
• Audio x 3
Video Format (Repeater Mode)
• VGA
• 480i/60 Hz
• 576i/50 Hz
• 480p/60 Hz
• 576p/50 Hz
• 720p/60 Hz, 50 Hz
• 1080i/60 Hz, 50 Hz
• 1080p/60 Hz, 50 Hz, 24 Hz
• 4K/60Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz
Digital Audio (Supported frequencies: 32 kHz to 96 kHz)
• Optical x 1
• Coaxial x 2
Video
• Composite x 3
HDMI Input
• HDMI x 4
Output jacks
HDMI Output
• HDMI OUT x 1
Audio Format
• Dolby TrueHD
• Dolby Digital Plus
• Dolby Digital
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Express
• DTS
• DSD 2-ch to 6-ch
• PCM 2-ch to 8-ch (Max. 192 kHz/24-bit)
Other jacks
Content Protection: HDCP 2.2 compatible
YPAO MIC x 1
Link Function: CEC supported
Analog Audio
• Speaker Out x 5 (FRONT L/R, CENTER, SURROUND L/R)
• Subwoofer Out x 1
• Headphone x 1
Video
• Composite x 1
TUNER
Analog Tuner
• [U.K. and Europe models]
FM/AM with Radio Data System x 1 (TUNER)
• [Other models]
FM/AM x 1 (TUNER)
79
En
Bluetooth
Rated Output Power (1-channel driven)
• [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω)
• [Other models] (1 kHz, 0.9% THD, 6 Ω)
Bluetooth version
• Ver. 2.1+EDR
Supported profile
• A2DP
Supported codec
• SBC
– Front L/R
100 W/ch
– Center
100 W/ch
– Surround L/R
100 W/ch
Maximum Effective Output Power (1-channel driven)
• [U.S.A. and Canada models]
Wireless output
• Bluetooth Class 2
Maximum communication distance
• 10 m (33 ft) without interference
(1 kHz, 10% THD, 8 Ω)
– Front L/R, Center, Surround L/R
130 W/ch
(1 kHz, 10% THD, 6 Ω)
– Front L/R, Center, Surround L/R
140 W/ch
• [Other models] (1 kHz, 10% THD, 6 Ω)
Compatible Decoding Formats
– Front L/R, Center, Surround L/R
Decoding Format
• Dolby TrueHD, Dolby Digital Plus
• Dolby Digital
• DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Express
• DTS, DTS 96/24, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1
135 W/ch
Dynamic Power (IHF)
• [U.S.A. and Canada models]
– Front L/R (8/6/4/2 Ω)
110/130/160/180 W
• [Other models]
– Front L/R (6/4/2 Ω)
Post Decoding Format
• Dolby Pro Logic
• Dolby Pro Logic II Music, Dolby Pro Logic II Movie, Dolby Pro Logic II Game
• DTS Neo: 6 Music, DTS Neo: 6 Cinema
110/130/150 W
Damping Factor
• Front L/R, 20 Hz to 20 kHz, 8 Ω
100 or more
Input Sensitivity / Input Impedance
Audio Section
• AV 2 etc. (1 kHz, 100 W/6 Ω)
200 mV/47 kΩ
Rated Output Power (2-channel driven)
Maximum Input Signal
• [U.S.A. and Canada models] (20 Hz to 20 kHz, 0.09% THD, 8 Ω)
• [Other models] (20 Hz to 20 kHz, 0.09% THD, 6 Ω)
– Front L/R
• AV 2 etc. (1 kHz, 0.5% THD, Effect On)
70 W+70 W
Output Level / Output Impedance
• [U.S.A. and Canada models] (1 kHz, 0.9% THD, 8 Ω)
– Front L/R
– Center
– Surround L/R
2.3 V
• SUBWOOFER
85 W+85 W
85 W
1 V/1.2 kΩ
Headphone Jack Rated Output / Impedance
85 W+85 W
• AV 2 etc. (1 kHz, 50 mV, 8 Ω)
100 mV/470 Ω
Frequency Response
• AV 2 etc. to Front (10 Hz to 100 kHz)
80
En
+0/-3 dB
FM Section
Signal to Noise Ratio (IHF-A Network)
• AV 2 etc. (Input 1 kΩ Shorted, Speaker Out)
110 dB or more
Tuning Range
• [U.S.A. and Canada models]
Residual Noise (IHF-A Network)
• Front L/R (Speaker Out)
• [Asia, Taiwan, Brazil and General models]
150 μV or less
• [Other models]
Channel Separation
• AV 2 etc. (Input 1 kΩ Shorted, 1 kHz/10 kHz)
• Step
• Mono
• Bass Turnover
• Treble Boost/Cut
• Treble Turnover
0.5 dB
• Mono
65 dB
• Stereo
64 dB
Harmonic Distortion (IHF, 1 kHz)
±6 dB/0.5 dB Step at 50 Hz
350 Hz
±6 dB/0.5 dB Step at 20 kHz
3.5 kHz
• Mono
0.5%
• Stereo
0.6%
Antenna Input
75 Ω unbalanced
Filter Characteristics
(fc=40/60/80/90/100/110/120/160/200 Hz)
• H.P.F. (Front, Center, Surround)
12 dB/oct.
• L.P.F. (Subwoofer)
24 dB/oct.
AM section
Tuning Range
• [U.S.A. and Canada models]
Video Section
• [Asia, Taiwan, Brazil and General models]
• [Other models]
Video Signal Type
• [U.S.A., Canada, Korea, Taiwan, Brazil and General models]
• [Other models]
NTSC
530 kHz to 1710 kHz
530/531 kHz to 1710/1611 kHz
531 kHz to 1611 kHz
General
PAL
Power Supply
Video Signal Level
• Composite
3 μV (20.8 dBf)
Signal to Noise Ratio (IHF)
MUTE, -80 dB to +16.5 dB
Tone Control Characteristics
• Bass Boost/Cut
87.50 MHz to 108.00 MHz
50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.)
70 dB/50 dB or more
Volume Control
• Range
87.5 MHz to 107.9 MHz
87.5/87.50 MHz to 108.0/108.00 MHz
• [U.S.A. and Canada models]
1 Vp-p/75 Ω
• [Taiwan, Brazil and General model]
Video Maximum Input Level
1.5 Vp-p or more
• [Korea model]
AC 220 V, 60 Hz
• [Australia model]
AC 240 V, 50 Hz
• [U.K. and Europe models]
• [Asia model]
Video Signal to Noise Ratio
50 dB or more
AC 120 V, 60 Hz
AC110 to 120/220 to 240 V, 50/60 Hz
AC 230 V, 50 Hz
AC 220 to 240 V, 50/60 Hz
Power Consumption
260 W
81
En
Standby Power Consumption
• HDMI Control Off
– [Taiwan, Brazil and General model]
0.5 W
– [Other models]
0.3 W
• HDMI Control On (No Signals)
0.9 W
Maximum Power Consumption
• [Taiwan, Brazil and General models]
470 W
Dimensions (W x H x D)
435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”)
Weight
7.4 kg (16.3 lbs)
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain
the latest manual, access the Yamaha website then download the manual file.
82
En
Yamaha Global Site
http://www.yamaha.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Department
© 2016 Yamaha Corporation
Published 01/2016 NV-A0
YH629A0/EN1
Download PDF

advertising