Document
Initial Setup
TV / DVD / VCR Combination
Operating Instructions
PV-DF2003/PV-DF2703
Basic Operation
Model No.
TV Operation
*Ability to play back may depend on recording conditions.
As an ENERGY STAR® Partner, Matsushita Electric Corporation
of America has determined that this product or product model
meets the ENERGY STAR® guidelines for energy efficiency.
This operating instruction book is designed for use with models PV-DF2003 and PV-DF2703.
Illustrations in this manual show the PV-DF2703. Features may vary, so please read carefully.
LSQT0668B
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 14 to 15.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the AC
power cord.
Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet only one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not tamper
with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances and
walking traffic. Do not rest heavy objects on, or roll
such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug
(polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords are fire
hazards.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes or discs.
For your protection:
a.Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa, rug,
or other soft surface.
b.Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator, in
direct sunlight, inside closed vehicles, in high
temperature [over 95 °F (35 °C)], or in over 75%
humidity. If unit is suddenly moved from a cold place
to a warm one, moisture may condense in unit and on
the tape causing damage. Never subject unit to
vibration, impact, or place it so that the surface is tilted
as internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level, and
adequately strong. The unit could
fall causing serious injury to a
child or adult and damage to the
unit.
• Move any appliance and cart
combination with care.
Quick stops, excessive force, and uneven surfaces
may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly grounded
to provide some protection against built up static charges and
voltage. Section 810 of the National Electrical Code,
ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical
Code) provides information regarding
proper grounding of the mast and
supporting structure, grounding of the
lead-in wire to an antenna discharge
unit, size of grounding conductors,
location of antenna discharge unit,
connection to grounding electrodes,
and requirements for the grounding
electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES
OR CIRCUITS
Locate an outside antenna system well away from power lines
and electric light or power circuits so it will never touch these
power sources should it ever fall. When installing antenna,
absolutely never touch power lines, circuits or other power
sources as this could be fatal.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,
such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,
unplug unit and have it inspected by a qualified service
technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, odours, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire
hazard. Do not put any foreign object on the tray.
• Keep magnetic objects, such as speakers, away from unit to
avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit
and cause electrical shock. Any substance, such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal
parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the unit
does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified by the
manufacturer, or have equal safety characteristics as original
parts. The use of unauthorized substitutes may result in fire,
electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a thorough safety
check be done as described in the manufacturer’s service
literature to ensure video unit is in safe operating condition.
Safety Precautions/Mesures de sécurité
Warning :
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
Caution :
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer
cet appareil à la pluie ou à une humidité excessive.
Attention :
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans
la borne correspondante de la prise et pousser jusqu’au fond.
FCC WARNING : Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate.
This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS
mark. It is recommended that only cassette tapes that
equipment. Only use those tapes with the
have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television
receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH
COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER
EN CAS D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTICE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize an
electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced
radio/TV technician for help. You may find the booklet, “Something About Interference” available from
FCC local regional offices helpful.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal
of these materials may be regulated in your community due to environmental considerations. For
disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the
unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any
inside part of this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any
problems.
Region Management Information
This unit is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this unit, this unit
cannot play this disc.
• The region number of this player is “1.”
• The player will play DVD-Video marked with labels containing “1”
or “ALL.”
Example:
1
3
Before Using
Loading the Batteries
Congratulations
On your purchase of one of the most
sophisticated and reliable products on the market
today. Used properly, it will bring you and your
family years of enjoyment. Please fill in the
information below. The serial number is on the
tag located on the back of your unit.
1) Open the cover.
2) Insert batteries as
marked.
Date of Purchase
Dealer Purchased From
3) Close the cover.
Dealer Address
Battery replacement caution
Dealer Phone No.
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Model No.
Serial No.
Prevent Accidental Tape Erasure
Break off the tab to
protect.
Record Tab
Screw driver
Accessories
To record again.
Remote Control
LSSQ0302
S UR RO UND
Cover the hole
with cellophane tape.
Record/Playback Time
Batteries 2 “AA”
Only use tapes with the
Tape Speed
Setting
To order accessories,
call toll free
1-800-332-5368.
4
mark in this unit.
Type of Video Cassette
T60
T120
T160
SP
(Standard
Play)
1 Hour
2 Hours
2 Hours
40 Minutes
LP
(Long Play)
2 Hours
4 Hours
5 Hours
20 Minutes
SLP
(Super Long
Play)
3 Hours
6 Hours
8 Hours
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Table of Contents
TV / VCR
Playback a Tape.............................................................................................................18
Record On a Tape..........................................................................................................18
Copy Your Tapes (Dubbing) .........................................................................................19
Basic DVD Operation ....................................................................................................20
DVD
TV / VCR
Timer Recording ............................................................................................................30
TV / VCR
Cable Box Universal Remote Control Feature............................................................32
Tape Operation ..............................................................................................................34
Special VCR Features ...................................................................................................38
V-Chip Control Feature ................................................................................................40
Audio Features ..............................................................................................................44
Video/Audio Menu .........................................................................................................46
Video/Audio Adjustment...............................................................................................47
Disc Operation ..............................................................................................................48
DVD Operation using On-Screen Displays .................................................................53
MP3/WMA/JPEG Playback Operation ..........................................................................56
DVD Lock Feature..........................................................................................................59
DVD
DVD
TV / VCR
Settings for DVD Operation ..........................................................................................60
Language Code List ......................................................................................................63
Before Requesting Service...........................................................................................64
Warning and Instruction Displays ...............................................................................66
Spanish Quick Use Guide/Guía para rápida consulta................................................67
Limited Warranty ...........................................................................................................74
Customer Services Directory .......................................................................................75
Index ...............................................................................................................................76
Timer Operation Advanced Operation For Your Information
TV Operation ..................................................................................................................22
MTS Broadcast/TV Stereo System...............................................................................23
Closed Caption System ................................................................................................24
TV Timer Features .........................................................................................................26
On-Screen Display (OSD) .............................................................................................27
FM Radio ........................................................................................................................28
TV Operation
TV / VCR
Basic Operation
Important Safeguards and Precautions ........................................................................2
Safety Precautions/Mesures de sécurité.......................................................................3
Before Using ....................................................................................................................4
Information (Unit, Cassette, Disc)..................................................................................6
Location of Controls .......................................................................................................8
Connections...................................................................................................................11
Initial Setup (Ready to Play) .........................................................................................14
Reset Language, Channels, Clock, Time Zone Adjust...............................................16
Initial Setup
TV / VCR
5
Information (Unit, Cassette, Disc)
Head Cleaning
Specifications
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Display
Head Clog Sensor
Picture Tube
During playback this
screen appears if
clogging is detected.
To clear message from
screen, press PLAY on
the remote or unit.
V I DEO HEADS MAY
NEED CLEAN I NG
PL EASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
VCR
Video Recording
System
END : PLAY
Audio Track
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully. Excessive
use of head cleaning tape can shorten the video head
life.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving
Time.)
■ Spring (First Sunday in April)
DST: ON ➞ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST: OFF ➞ Turns clock back one hour.
• If your area does not observe Daylight Saving Time,
select DST : OFF (see “Clock” on pages 16 and 17).
• Keep these time changes in mind when programming
the unit for timer recordings.
Features for a Quality Picture
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 NUMBER
on the unit
key on the remote control or CH
until the picture clears up. To return to Auto
Tracking, press POWER off, then on again a few
seconds later.
V-Lock Control
In Still mode, the 3 or 6 NUMBER key on the
on the unit operate as a
remote control or CH
V-Lock control to reduce jitter.
Apparatus Claims of U.S. Patent Nos. 4,631,603,
4,577,216, 4,819,098, and 4,907,093, licensed
for limited viewing uses only.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. Patents and other intellectual
property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is
prohibited.
6
20 inch measured diagonal pure flat
Picture Tube (PV-DF2003)
27 inch measured diagonal pure flat
Picture Tube (PV-DF2703)
4 rotary heads helical scanning
system
1 track (Normal)
2 channel (Hi-Fi Audio Sound)
Tuner
Broadcast Channels VHF 2 ~ 13, UHF 14 ~ 69
Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
CABLE Channels
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band Range
General
Power Source
Power
On
Power
Consumption Power
Off
Television System
Speaker
Operating
Temperature
Operating Humidity
Weight
Dimensions
(W x H x D)
87.5 MHz ~ 108.1 MHz
120 V AC, 60 Hz
Approx. 134 W (PV-DF2003)
Approx. 161 W (PV-DF2703)
Approx. 3.5 W
EIA Standard NTSC color
2 pieces 5 W
5 °C ~ 35 °C (41 °F ~ 95 °F)
10 % ~ 75 %
30 kg (66.1 lbs.) (PV-DF2003)
52 kg (114.4 lbs.) (PV-DF2703)
604 mm (23-3/4″) x 523 mm (20-5/8″) x
503 mm (19-3/4″) (PV-DF2003)
760 mm (29-7/8″) x 651 mm (25-5/8″) x
503 mm (19-3/4″) (PV-DF2703)
Discs played
12 cm (5″) single-sided, single-layer
12 cm (5″) single-sided, double-layer
12 cm (5″) double-sided, double-layer
(one layer per side)
DVD disc
(DVD-Video, DVD-R) 8 cm (3″) single-sided, single-layer
8 cm (3″) single-sided, double-layer
8 cm (3″) double-sided, double-layer
(one layer per side)
Compact disc
(CD-DA, VIDEO CD, 5″ (12 cm) disc
3″ (8 cm) disc
CD-R, CD-RW)
MP3, WMA, JPEG
Digital audio output
Optical digital output Optical connector
Pickup
Wavelength
655 nm (DVD)
790 nm (Video CD/CD)
Laser power: CLASS II
Note
• Designs and specifications are subject to change
without notice.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Discs that can be played
Disc
Logo
Disc formats supported by this
unit
DVD-Video
• DVD-Video format
DVD-R
• DVD-Video formatted discs
(finalized*)
It may not be possible to play these
discs in all cases due to the type of
disc or condition of the recording.
Video CD
• Video-CD format
CD-DA
• CD-DA format
CD-R
• CD-DA format
• Video-CD format
• MP3/WMA/JPEG file and finalized*.
CD-RW
• Discs played 8 cm (3″) or 12 cm (5″)
• * A process that allows play on compatible equipment.
Discs which cannot be played with this unit
• CD-ROM
• DVD with Region No. other
• CDV
than “1” or “ALL”
• CVD
• DVD of PAL system
• CD-G
• DVD-ROM
• CD-TEXT
• DVD-AUDIO
• SACD
• DVD-RW
• Photo-CD
• DVD+RW
Definition of Terms
Angle
Some DVD discs feature scenes simultaneously shot from different
angles. The ANGLE button can be used to view the scene from different
angles. (ANGLE Indicator lights up on the unit when a scene recorded at
different angles is detected.)
Chapter Number
Titles are subdivided into numbered sections. You can quickly search for
a favorite scene using these numbers.
DVD
A high-density optical disc on which high-quality pictures and sound have
been digitally recorded. DVD incorporates new video compression
technology (MPEG II) and high-density recording technology which allow
entire movies to be recorded with incredible playback quality.
Playback Control
With Video CD (version 2.0), scenes or information may be selected for
viewing or listening from an interactive menu that appears on the TV
screen.
Subtitles
Written dialogue which appears at the bottom of the screen.
Time Number
The elapsed play time from the start of a disc or title. Use to quickly find
scenes. (May not work with some discs.)
Title Number
For DVD discs with two or more titles, the title is numbered as title 1, title 2,
etc.
Track Number
Numbers assigned to tracks on Video CDs and CDs to allow specific
tracks to be quickly located.
Video CD
CD containing picture and sound with same quality level as video tape.
This unit also supports Video CDs with playback control (version 2.0).
Handling precautions
• Sticking a label on the disc may impair
DVD-R playback.
• Do not attach sticker to discs. (Do not use
discs with exposed adhesive from tape or
left over peeled-off stickers.)
• Only hold disc by
edges as shown.
Fingerprints, dirt, and
scratches can cause
skipping and
distortion.
• Do not write on
label side of disc.
• Never use record
cleaning sprays,
benzine, thinner,
static electricity
prevention
liquids, or
Disc tray
any other
solvent.
Disc
• Be careful
not to drop
or bend
disc.
• Do not place more than 1 disc on disc tray.
• Do not try to close disc tray when disc is not
properly placed.
• Always store discs in their proper cases
when
not in use.
Initial Setup
Disc type
Disc Handling
To clean disc surface
With a soft, damp (water only) cloth,
gently wipe from the center hole to the
outer edge as shown below. (Wiping in a
circular pattern will scratch the surface.)
If disc is brought from a cold to a
warm
environment, moisture may form on
the disc
Wipe away moisture with a soft, dry,
lint-free cloth before using disc. (See
above.)
Improper disc storage
Discs could be damaged if stored or left
in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
7
Location of Controls
Remote Control Buttons
EJECT/OPEN/CLOSE
See next page.
DVD
Sets to DVD mode.
POWER
Turns the unit on or off.
LIGHT
See next page.
TV/VCR
Sets to TV/VCR mode.
DSS/CABLE
Sets the remote to control some
basic DSS or Cable box
functions.
FM
Receives FM radio signal.
MUTE
Mutes the sound instantly.
CHANNEL UP/DOWN
Selects a channel.
SURROUND
Creates a deeper, 3-D sound effect.
NUMBER Keys
Selects a channel directly.
ANGLE
Selects the desired angle
in DVD mode.
AUDIO
Selects the desired audio mode.
TITLE
Selects the desired title by number on
some DVDs.
SELECT
Controls navigation around on-screen
menu.
ACTION
Displays Main Menu.
SET
Sets a selected menu.
REW/SLOWRewinds tape and searches reverse
scene. Decreases slow motion speed
in Still mode.
RAPID TUNE
Displays the last channel you
were watching.
ADD/DELETE/CLEAR
Adds or deletes a channel.
Cancels an item on the screen.
SUBTITLE
Selects a different subtitle
language.
DISPLAY/ENTER
Displays the TV status and
clock. In DVD mode, displays
disc and unit information. In
DSS or CABLE mode, it may be
necessary after channel
selection.
MENU
Displays DVD menu.
PROGRAM
Displays SET PROGRAM
screen. You can set Timer
Program and On-Timer
STILL/PAUSE
Pauses picture in Playback mode and
frame advance picture in Still mode.
FF/SLOW+
Fast forwards tape and forward
visual search. Increases slow
motion speed in Still mode.
/SEARCH
SKIPSkips back one chapter or track. Goes
to previous menu screen. Goes directly
to the desired recording. Locates end
point of recording.
ZOOM/COUNTER RESET
Enlarges specific portions of
DVD picture. Resets to “0:00:00”
at desired portion of tape.
PLAY
Begins playback.
/CM SKIP/ZERO SEARCH
SKIP+
Skips one chapter or track. Goes to next
screen. In Stop mode, goes to the counter
“0:00:00.” In Play mode, skips over 1 to 3
minutes of tape.
8
VOLUME UP/DOWN
Adjusts volume.
REC
Records a program.
RETURN/SPEED
Returns to DVD menu screen.
Selects recording speed of tape.
STOP
Stops recording or playback.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
LIGHT button:
EJECT/OPEN/CLOSE button:
When this button is pressed in TV-VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
Initial Setup
When LIGHT is pressed, (DVD,
, DSS/CABLE, CH UP/DOWN, VOL UP/DOWN) buttons will light for
5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the batteries.
Indicators on the Front Panel
<Model PV-DF2703 unit shown>
REC Indicator (RED)
Lights during recording. In Rec
Pause or OTR Pause mode,
the indicator flashes.
Pg 18.
ANGLE Indicator (RED)
Lights when a scene
recorded at a different
angles is detected. (DVD
only).
Pg 49.
Remote Sensor
ON TIMER Indicator (ORANGE)
Lights when the On-Timer is set.
Pg 26.
PROG TIMER Indicator
(GREEN)
Lights when the unit is set
for Timer Recording. It
flashes when a Timer
Recording has been set
with no tape inserted, the
clock is not set, or the tape
is in motion.
Pg 30.
9
Location of Controls (continued)
Front View of the unit
<Model PV-DF2703 unit shown>
Built In Speaker
If the disc cannot be removed,
First unplug unit.
Then, prepare a rigid wire (e.g.
an extended paper clip, etc.) and,
applying moderate force, insert it
straight into the hole at the base of
the tray. The tray will eject a little.
Now, pull the tray all the way out and
remove the disc.
Disc Tray
Phones Jack
Connect an earphone
or headphones.
Audio/Video Input
Connector 2 (LINE 2)
Connect from other
component.
S-Video Input Connector 2
(LINE 2)
Connect from other component
with S-Video.
POWER
Turns the unit on or off.
Disc Operation
STOP
Stops playback.
PAUSE
Pauses picture in Playback mode
and frame advance picture in Still
mode.
PLAY
Begins playback.
SKIP
Skips back one chapter or track.
Goes to previous menu screen.
SKIP
Skips one chapter or track.
Goes to next screen.
OPEN/CLOSE
Opens or closes the disc tray.
10
Cassette Compartment
Tape Operation
REC
Records a program.
FAST FORWARD/SEARCH
Fast forwards tape and
forward visual search.
Increases slow motion
speed in Still mode.
PLAY
Begins playback.
REPEAT
Set to see a recording over
and over.
REWIND/SEARCH
Rewinds tape and searches
reverse scene. Decreases
slow motion speed in Still
mode.
STOP
Stops playback.
EJECT
Eject the tape.
TV/FM
Sets to TV/FM mode.
CHANNEL UP/DOWN
Selects a channel.
TRACKING UP/DOWN
Reduces picture noise during Playback
and Slow Motion.
VOLUME UP/DOWN
Adjusts volume.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
11
Connections (continued)
Audio connections
Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on
DVDs by connecting an amplifier and speakers. There are two types of connection, digital and analog.
■ Digital connection
■ Analog connection
Connect an amplifier with Dolby Digital and
DTS decoders to enjoy surround sound.
You can also enjoy stereo sound with
sampling frequencies of 48 kHz if the material
is not copy-protected and the equipment you
connect is compatible with these signals.
Connect an amplifier to enjoy high-quality stereo
sound with sampling frequencies of 96 kHz.
Firmly
connect the
cable to the
connector.
OPTICAL
Speakers (example)
Speakers (example)
Connect three or
more speakers for
surround sound.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
IMPORTANT NOTE:
Check List
Enjoying digital audio output from the
digital audio output connector
Notes on audio output from the optical
digital audio output connector
Disc
Sound
recording
format
Dolby Digital
DVD
Linear PCM
(48/96 kHz
16/20/24 bit)
dts
Video CD MPEG 1
CD
Linear PCM
MP3
MP3
WMA
WMA
Optical digital audio output
from connector
Dolby Digital bitstream
(1-5.1 ch) or PCM (48 kHz
sampling/16 bit only)*1
Linear PCM (2ch)
(48 kHz sampling/16 bit
only)*2
Bitstream or PCM (48 kHz
sampling/16 bit only)*1
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)
Linear PCM
(It depends on the MP3 file)
Linear PCM
(It depends on the WMA file)
*1 The type of audio output from the connector can be
selected by the Settings for DVD Operation. (See
page 61.)
*2 Sound having 96 kHz sampling is converted into 48
kHz sampling when it is output from the unit’s optical
digital audio output connector.
Caution for optical digital audio
output connector:
• When connecting an amplifier (with an Optical
digital input connector) which does not contain
the Dolby Digital or dts decoder, be sure to
select “PCM” at “Dolby Digital” and “PCM” at
“dts” of the Settings for DVD Operation “AUDIO
OUTPUT” (see page 61). Otherwise, any
attempt to play DVDs may cause such a high
level of noise that it may be harmful to your
ears and damage your speakers.
• When a dts decoder is connected, please
select “Bitstream” at “dts” of the Settings for
DVD Operation “AUDIO OUTPUT.” If “PCM” is
selected, there will be stereo sound. (See
page 61).
• Video CDs and CDs can be played as usual.
Initial Setup
Turn down the volume, then turn this unit, as well
as other equipment to be connected, off before
proceeding with connection.
Do not block ventilation holes of any equipment
and arrange them so that air can circulate freely.
Read through the instructions before connecting
other equipment.
Ensure that you observe the color coding when
connecting audio and video cables.
Note
• Some dts decoders which do not support
DVD-dts Interface may not work properly with
the unit.
Manufactured under license from Digital
Theater Systems, Inc. US Pat. No.
5,451,942, 5,956,674, 5,974,380,
5,978,762 and other world-wide patents
issued and pending. “DTS” is a registered
trademark of Digital Theater Systems,
Inc. Copyright 1996, 2000 Digital Theater
Systems, Inc. All rights reserved.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby
Laboratories.
For your reference:
• Dolby Digital is a digital sound compression technique
developed by the Dolby Laboratories Licensing Corporation.
Supporting 5.1-channel surround sound, as well as stereo
(2-channel) sound, this technique enables a large quantity of
sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs. While
CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48
kHz/16 bit up to 96 kHz/24 bit.
• If you have a Dolby Pro Logic Surround decoder, you will
obtain the full benefit of Pro Logic from the same DVD
movies that provide full 5.1 channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround
mark. For information on Panasonic or Technics Dolby Pro
Logic Surround Sound Decoders please contact your local
dealer.
13
Initial Setup (Ready to Play)
Please make all cable or antenna connections before powering on.
Initial Setup (Ready to Play)
Press
on the remote for TV-VCR mode.
1
Plug the unit power cord into an AC wall outlet.
2
Press POWER* on the remote or unit. The unit
comes on and auto channel and clock set
starts.
EJECT
POWER
TV-VCR
S UR RO UND
SELECT
CH AUTO SET PROCEEDING
SET
ACTION
• If you use a cable box, turn it on and set it to the Public
Broadcasting Service (PBS) channel in your time zone.
If you use a DSS receiver, it must be turned off.
AUTO CLOCK SET
PROCEEDING
CANCEL : PRESS STOP KEY
3
Settings are made automatically. When setup
is done, this screen appears.
2 / 6 / 2003 THUDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
STOP
If AUTO CLOCK SET IS INCOMPLETE screen appears,
set the clock using MANUAL CLOCK SET procedure on
next page.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
14
Notes
• Function buttons are inoperative during
Initial Setup.
• To remove a cassette during Auto Set,
press EJECT twice on the remote or
STOP twice on the unit. In this case,
settings must be made manually. (See
pages 16-17.)
• Depending on conditions, Auto Clock
Set may take longer than 30 minutes. If
so, press STOP to stop setup and
perform settings manually. (See pages
16-17.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
THU
Note to CABLE system installer:
This reminder is provided to call the CABLE (Cable TV) System Installers attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close to the point of cable entry as
practical.
15
Reset Language, Channels, Clock,
1
Press ACTION*
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
2
CH
CLOCK
SELECT :
END
: ACT I ON
to display MAIN MENU.
1
SET : SET
■ Language
■ Channels
1) Press
to
select language
icon.
1) Press
select “CH.”
■ Clock
to
1) Press
to
select “CLOCK.”
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
1
CH
CLOCK
SET : SET
2) Press SET.
2) Press SET.
2) Press SET
repeatedly.
MENU PRINCIPAL
HOLA
DVD
BLOQUEO IDIOMA
53
TV
RELOJ
1
CANAL
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
For Spanish
MENU
DVD
BLOCAGE LANGUE
TELE
HORLOGE CANAL
SEL. :
FIN
REGLER : SET
: ACT I ON
For French
For English
3) Press ACTION
to exit.
16
3) Press
to select
“ANTENNA,” then
press SET to set
your antenna system
(“TV” or “CABLE”).
4) Press
to select
“AUTO SET,” then
press SET.
(“TIME ZONE ADJUST”
appears only when
auto clock is set.)
3) Press
to select
“MANUAL,” then
press SET.
(For Auto Clock Set,
select “AUTO CLOCK
SET,” and press SET.)
• After Channel Auto Set is
finished, Clock Auto Set will be
performed.
(If clock is set manually, Clock
Auto Set will not be performed.)
<Example MANUAL
CLOCK SET screen>
Continued on
the next page.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
17
Playback a Tape Record On a Tape
1
Insert a cassette.
• The unit power comes
on automatically.
Record tab
1
2
3
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
■
➞
➞
■
➞
➞
■
➞
➞
■
➞
➞
Insert a tape with record tab.
• The unit power comes on automatically.
Press CH
a channel.
or NUMBER keys to select
• For “LINE” input, see bottom of next page.
Press SPEED to select recording speed
(see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
Press PLAY* to play a tape.
• If tape has no record tab (see page 4), auto play
begins.
Forward/Reverse scene search
Press FF/SLOW+ or REW/SLOW-.
Press again or PLAY to release.
Still (Freeze) picture
Press STILL/PAUSE.
Press PLAY to release.
Slow Motion picture
Press FF/SLOW+ (increases speed) or
REW/SLOW- (decreases speed) in Still
mode.
Press PLAY to release.
Frame by Frame picture
Press STILL/PAUSE in Still mode.
Press PLAY to release.
• These features work best in SP or SLP mode.
• After the unit is in Still or Slow mode for 3 minutes, it will
switch to Stop mode automatically to protect the tape
and the video head.
Press REC to start recording.
• To edit out unwanted portions, press
STILL/PAUSE to pause and resume recording.
• You cannot view another channel during
recording.
■ Stop ➞ Press STOP
■ One Touch Recording (OTR)
[recording in progress]
Press REC
Normal Rec
repeatedly to set
the recording length 4:00 3:00
(30 min - 4 hours.)
0:30
2:00
1:00
1:30
• The unit stops recording at a preset time.
• PROG TIMER Indicator lights on the unit.
• It is not possible to record from DVD/Video CD/CD
to VHS tape using this unit.
• After the unit has been in Rec Pause mode for 5
minutes, it will stop automatically to protect the tape
and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
EJECT
S UR RO UND
■ Stop ➞ Press STOP
■ Rewind tape ➞ Press REW/SLOW- in
Stop mode
■ Fast forward tape ➞ Press FF/SLOW+
in Stop mode
■ Eject tape ➞ Press EJECT on the
remote or STOP/EJECT on the unit
4
Operation using unit buttons
PLAY/REPEAT
Insert a tape.
CH
Press to stop
and/or eject tape.
18
REC
REC Indicator
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Copy Your Tapes (Dubbing)
*Important:
If a remote control button does not work when pressed, press the
the button again.
button on the remote and try
Connections you’ll need to make
Recording (Editing) unit
Playing (Source) VCR
VIDEO IN2 L-AUDIO IN2-R S-VIDEO IN2
If cables are connected to both connectors (S-VIDEO IN or VIDEO IN), the S-VIDEO
signal will be selected automatically. (The S-VIDEO signal has priority.) If you would
like to display the VIDEO signals being input to the VIDEO IN connector, do not
connect any cables to the S-VIDEO IN connector.
Playback (Source)
1
2
3
Basic Operation
R-AUDIO IN1-L VIDEO IN1 S-VIDEO IN1
R-AUDIO OUT-L VIDEO OUT S-VIDEO OUT
Recording (Editing) unit
Insert blank tape with
record tab.
Insert pre-recorded
tape.
• Dubbing tapes protected with
Copy Guard will have poor
quality results.
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then press PAUSE at starting
point to put in Standby mode.
Press REC, then press STILL/PAUSE
immediately to put in Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
Press PLAY to start dubbing.
Press STILL/PAUSE to start dubbing.
Press STOP to stop dubbing.
Press STOP to stop dubbing.
Selecting Input Mode
Method 1:
Press CH
. The display will change as follows.
LINE2
Caution
• Unauthorized exchanging and/or copying
of copyrighted recordings may be copyright
infringement.
• Please note that some tapes cannot be dubbed
on this unit. Also, it is not possible to dub
DVD/Video CD/CD to VHS tape using this unit.
LINE1
1
3
2
(CABLE) (TV)
125 or 69
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV,” then press SET
for SET UP TV screen.
to select “INPUT SELECT,” and
c Press
then press SET to select “TUNER,” “LINE1” or
“LINE2.”
d Press ACTION twice to exit this mode.
19
Basic DVD Operation
1
2
Press POWER* on the remote or unit.
Insert a disc.
• If a disc is already inserted, go to step 3.
(Depending on the disc, playback may start
automatically.)
1) Press OPEN/CLOSE.
2) Place disc into disc tray.
1
2
• Hold disc by its edges only (page
7) with printed side up and use
guides to place into tray. Use 1
3″(8 cm) or 2 5″ (12 cm) disc.
Operation using unit buttons
3Press PLAY.
Press
2Insert disc. 2•6 OPEN/CLOSE.
1 Press POWER. 5 Press STOP.
*1 Interactive DVD...
May include multiple camera angles, stories, etc.
*2 Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that appears
on the screen.
20
To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD)
5
6
Press STOP to stop play.
Press OPEN/CLOSE to eject the disc.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
■ Forward/Reverse rapid scene search
➞ Press FF/SLOW+ or REW/SLOWduring play.
➞ Press PLAY to release.
• Starting forward/reverse search during play started from
menu on Video CDs may recall menu.
• Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
■ Forward/Reverse Chapter/Track Skip
Pressing SKIP- |
once midway through a
chapter/track returns to start of that chapter/track.
Each additional press skips back one chapter/track.
| or SKIP- |
• Pressing SKIP+
during play
started from menu on Video CDs may recall menu.
Current playback position
Chapter/Track Chapter/Track Chapter/Track Chapter/Track
Reverse Skip
Forward Skip
■ Still (Pause) Picture
➞ Press STILL/PAUSE during play.
➞ Press PLAY to release.
• DVD/Video CD : The unit will enter Still picture mode.
• CD : The unit will enter Pause mode.
■ Frame by Frame picture (DVD/Video
CD)
➞ Press STILL/PAUSE in Still mode.
➞ Press PLAY to release.
• Each press advances picture one frame.
• Hold down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically (see page 62).
■ Slow Motion picture (DVD/Video CD)
➞ Press FF/SLOW+ or REW/SLOW- (DVD
only) in Still mode.
➞ Press PLAY to release.
RESUME function
The unit memorizes the point where STOP is
pressed (STOP display on the screen).
Press PLAY to resume play from this point.
Pressing STOP again or opening the tray cancels
RESUME, however, RESUME is not canceled
when power is turned off and on.
• RESUME works only with discs for which elapsed
play time is displayed during play.
Auto-Power Off function
Basic Operation
| or SKIP- |
during
➞ Press SKIP+
play.
Each press skips a chapter (DVD) or track
(Video CD/CD).
• When
appears on the screen while a
button is being pressed, it means that the
corresponding operation is prohibited by the
unit or the disc.
Power turns off after unit has been in Stop mode
(DVD) for about 5 minutes.
Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)
1. Do steps 1-3 (previous page).
When menu appears, press STOP.
2. Press NUMBER key(s) to select desired
track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP, and press PLAY, then the menu
appears. Now, go to step 4 (previous page).
Notes
• Please read the disc jacket for operation information.
• If a single sided disc is placed in upside down, “THIS
TYPE OF DISC CANNOT BE PLAYED. PLEASE
INSERT A DIFFERENT DISC” is displayed.
• Remove disc and press unit POWER off when not in
use.
• Disc continues to rotate with menu displayed even
after play is done. Press STOP to clear menu display
when finished with menu.
• Slow motion speed, slow at first, is increased with
each additional press of the button up to 5 levels.
• Reverse slow motion is not available for video CDs.
21
TV Operation
1
*Important: If a remote control button does not work
when pressed, press the
button on the
remote and try the button again.
Press POWER* on the remote or unit.
Use CH
or
NUMBER keys to
select a channel.
2
VOL+/VOLPOWER
Press VOL + or
VOL - to adjust
volume.
3
24
PHONES
Jack
CH
■ Using the 100 key
When selecting CABLE channels 100 to 125 with
the NUMBER keys, first press the 100 key, and
then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you
were watching.
■ Audio Mute
Press MUTE to instantly mute the sound. Press
again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones
(not supplied) to the Phones Jack.
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MTS Broadcast/TV Stereo System
Equipped with
-TV Noise
Reduction for true MTS
reproduction.
-TV Noise
Reduction is required for good
stereo separation and audio fidelity.
is a registered trademark,
and is licensed by
Technology Licensing.
Receivable Broadcast Types
The following are possible audio broadcast types and
on-screen displays. The signal being received is indicated with
an “ ” mark while the selected audio mode is indicated with
an arrow. To change the audio mode for these broadcasts, see
the “Audio Mode for TV Viewing” section below.
Press DISPLAY to display the broadcast signal being
received.
1 2 : 0 0AM
CH08
SP
STEREO
SAP
MONO
S UR RO UND
1 2 : 0 0AM
CH08
SP
MTS Stereo broadcast
Multi-channel Television Sound Stereo
broadcast. Select STEREO audio
mode.
• If stereo broadcast is weak and the
display flickers, select MONO audio mode
for possible improvement.
AUDIO
DISPLAY
1 2 : 0 0AM
CH08
SP
STEREO
SAP
MONO
1 2 : 0 0AM
STEREO
SAP
MONO
CH08
SP
SAP broadcast
Secondary Audio Program (sub
language). Select SAP audio mode for
the sub language.
TV Operation
STEREO
SAP
MONO
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo
(main language) and Secondary Audio
Program (sub language) broadcasts
are being received simultaneously.
Select the STEREO or SAP audio
mode.
MONO broadcast
Normal monaural sound broadcast.
Audio Mode for TV Viewing
Press AUDIO to select the desired audio mode as described above.
(Arrow shows selection.)
• Each press of AUDIO will change the audio mode as shown below.
• “SAP” is selected with first press of AUDIO.
< Example >
Press AUDIO
STEREO
SAP
MONO
STEREO
SAP
MONO
STEREO
SAP
MONO
Press AUDIO
Press AUDIO
23
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes
useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION* to display MAIN MENU.
Closed Caption Mode Selections
Caption Mode: CAP C1 or C2
A narration of selected TV
1) Press
M A I N MENU
programs is displayed.
to select “TV.”
Check TV program listings for CC
LOCK LANGUAGE 2) Press SET to
DVD
(Closed Caption) broadcasts.
display SET
53
Caption Mode: TEXT C1 or C2
CH
TV
CLOCK
UP TV screen.
Most of the screen will be blocked
SELECT :
SET : SET
END
: ACT I ON
out. When the TV station
broadcasts information, such as
1) Press
to
SET UP TV
program listings, it will appear in
select
CAPT I ON
this space.
I NPUT SELECT
: TUNER
“CAPTION.”
SET UP V I DEO / AUD I O
Caption Mode: OFF
DVD VOL ADJU
: +2
2) Press SET to
Closed Caption/Text narration will
REMOTE W
ARNING : O
N
display
not be displayed.
SET : SET
SELECT :
CAPTION
1
3
END
4
: ACT I O
screen.
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
SET
: SET
END
: ACT I ON
OFF
CAP C1
TEXT C2
1) Press
to
select
CAPTION
MODE.
2) Press SET
repeatedly to
select mode.
(See left.)
Notes
• The closed caption or text signal may
be broadcast over C1, C2, or both.
Also, text contents can vary so you
may wish to try different settings.
• While recording one station and
watching another, Captioning will
not be displayed.
TEXT C1
CAP C2
5
Press ACTION three times to return to
the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record : Record normally. Closed Caption/Text signal, if present, is recorded
automatically.
Playback : Start playback. Perform above steps to select desired caption mode.
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
the remote and try the button again.
button on
Caption On Mute Feature
Closed Caption narration, if available, is displayed when
MUTE button is pressed for silence.
1
MUTE
Press ACTION to display MAIN MENU.
2
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
CH
CLOCK
S UR RO UND
SELECT :
END
: ACT I ON
SELECT
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
1) Press
to select
“CAPTION.”
2) Press SET to display
CAPTION screen.
SET : SET
SELECT :
END
: ACT I ON
SET
ACTION
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
1) Press
to select
CAPTION MODE.
2) Press SET repeatedly
to select “OFF.”
TV Operation
3
1
1) Press
to select
“TV.”
2) Press SET to display
SET UP TV screen.
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to select CC
ON MUTE.
2) Press SET repeatedly
to select desired mode.
5
NO
CAP C1
• Each press of SET will
change the display as shown
left.
• The caption may be broadcast
over CAP C1 or C2.
CAP C2
6
Press ACTION three times to return to the normal
screen.
7
Press MUTE to mute the sound and display
closed captioning.
Note
• When a disc supporting closed caption is
used, the subtitle and the closed caption
may overlap. In this case, turn the subtitle
or caption on mute mode off. (See page
48.)
• To cancel, press MUTE again.
25
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of
4 modes (TV, VCR Playback, FM radio, or DVD/Video
CD/CD.) You can also combine the On-Timer with a
one minute alarm that gradually increases in volume.
1
2
Press PROG* to display SET PROGRAM
screen.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
3
1) Press
to select
desired settings.
2) Press SET to set
the ON-TIMER
time or ON-TIMER
mode.
ON T I MER
ALARM : ON
SELE CT HOUR
SELECT :
SET
: SET
END
: PROG
• ON-TIMER mode
selection order
CH02
CH03
CH125
CH01
VCR
DVD
4
FM9
FM8
FM1
• Make sure a tape is
inserted if Playback
mode is selected.
• Make sure a disc is
inserted if DVD
(DVD/Video CD/CD)
mode is selected.
• See “FM Radio” on pages
28 and 29 for instructions
on how to preset FM
stations.
Press
to select
ALARM “ON” or
“OFF.”
ON T I MER
ALARM : ON
SELE CT ALARM
CANCEL : ADD / DLT
SELECT :
SET
: SET
END
: PROG
1) Press
to select
“ON TIMER.”
2) Press SET to
display ON TIMER
screen.
BACK :
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
and
to move back and correct.
use
5
Press PROG to set ON TIMER.
This unit can be set for auto power off.
1
2
Press PROG to display SET
PROGRAM screen.
1) Press
to
select SLEEP
TIMER.
2) Press SET
repeatedly to
select the
desired time.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
SLEEP TIMER 30
60
90
00
To cancel,
press SET repeatedly until 00 appears.
3
Press PROG to return to the normal
screen.
• Pressing DISPLAY with sleep timer set
displays remaining time.
• “ON TIMER SET” is displayed.
• ON-TIMER Indicator lights up on the unit.
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear
the time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
26
Sleep Timer
• If no button on the remote or unit (including a
button used to turn off the alarm) is pressed
within 60 minutes after unit turns itself on, it will
turn itself back off.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
On-Screen Display (OSD)
*Important:
If a remote control button does not work when pressed, press the
the button again.
button on the remote and try
TV/VCR Status & Clock Display
Press DISPLAY to display or remove the overlay.
Function Status
S UR RO UND
Rec Time
Remaining
(OTR mode
only, see page
18.)
Current Time
CH08
REC
1 2 : 0 0PM
-0 : 1 2 : 3 4
0 : 25
SP
STEREO
SAP
MONO
Receivable
Broadcast
Types (See
page 23.)
Counter
Tape
Speed
(See
page 4.)
DISPLAY
SELECT
SET
Blue Screen Display
PROG
TV Operation
ADD/DLT
Channel
Whenever a blank section of a tape comes up in Playback
mode, or when the selected channel has no broadcast signal
with the Weak Signal Display Feature set to “OFF” (see page
38), the screen will turn solid blue.
Channel & Function Display
When a function button is pressed (PLAY, FF, etc.) or you
change channels, the unit mode or channel number will be
displayed.
CH08
PLAY
27
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1
MHz. You can set the On-Timer (page 26) to wake up to your favorite radio station.
FM Radio Setup
1
Press FM* on the remote or TV/FM on the
unit to display FM radio mode.
2
1 2 : 0 0PM
3
1 2 : 0 0PM
FM 1
FM 1
Press a NUMBER
key (1~9) to select the
FM preset number.
87. 5MHz
1) Press CH
to
select the desired
radio station. (Each
8 7. 7MHz
MEMORY : PRESS ADD / DLT KEY
2) Press ADD/DLT to
set the radio
station.
1 2 : 0 0PM
FM 1
press changes
frequency by 200
kHz.)
8 7. 7MHz
MEMOR I ZED
To Make Corrections,
select station with a
NUMBER key, then do step
3 again.
TV/FM
Hold down CH or
for a few seconds,
then release to
quickly scan for FM
stations in your area.
• To cancel, press CH
or
while in search
mode.
CH
To exit FM mode, press
or DVD on the remote
or TV/FM on the unit.
FM Antenna Setup
Make sure FM tuning is done correctly (see FM
Radio Setup).
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
1
CH
1) Press
to
select “TV.”
2) Press SET to
display SET UP TV
screen.
SET : SET
Continued on next page.
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the FM button on the
remote and try the button again.
3
TV-VCR
DVD
to
1) Press
select FM
ANTENNA.
2) Press SET to
select “INT
SET : SET
SELECT :
(INTERNAL)” or
END
: ACT I ON
“EXT
(EXTERNAL)” to
■ For cable TV users determine which
one sounds best.
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
➞ “INT”
■ For antenna users
➞ “EXT”
FM
S UR RO UND
CH
NUMBER
keys
4
Press ACTION twice to end setup.
SELECT
SET
ACTION
Using FM Radio
1
2
Press FM on the remote or TV/FM on the
unit to display FM radio mode.
1 2 : 0 0PM
FM 1
87. 5MHz
TV Operation
ADD/DLT
DISPLAY
AUDIO
Press a NUMBER
key (1~9) to select
a preset FM number
(see FM Radio Setup
on page 28).
To exit FM mode,
or DVD on the remote or TV/FM
press
on the unit.
Notes
• FM radio cannot be recorded on a Video
cassette.
• You may get better reception by
repositioning the unit.
• You cannot select FM Radio mode during
playback or record, or while a blue back
screen (PROG, ACTION, MENU) is
displayed.
• Once stations are set, the selected station
and current time are displayed when FM
Radio mode is entered. To remove time,
press DISPLAY. If DISPLAY is pressed
again, the unit status screen appears.
Audio Mode for FM Radio
1 2 : 0 0PM
STEREO
MONO
FM 1
8 7. 7MHz
Press AUDIO repeatedly
to select “STEREO” or
“MONO” in FM Radio
mode.
29
Timer Recording
You can set up to 8 programs to be recorded while you
are away.
1
2
Press PROG* to display SET PROGRAM
screen.
1) Press
to
select TIMER
PROGRAMMING.
2) Press SET to
display screen.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
• If a program is already in memory, press
SET to select an unused program number.
3
Check List
Cable or antenna is connected.
Power cord is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
, and
to select
to
TODAY
set the recording
SP
------------------------ DATE.
SELE CT START DATE
DATE
START
STOP
CH
Press
7 FR I --:-- --:-- -- and SET or
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT =
Same time once a week
SELECT :
SET
: SET
: PROG
END
Example
8
Today’s
Date
9
31
SELECT
7
/
WEEKLY
(SAT)
1
2
6
Selection Order
WEEKLY
(MON)
DAILY
WEEKLY
(SUN)
Repeat step 3 to set:
• Start time, Stop time
• Channel (or LINE for outside source)
• Speed (SP, LP, SLP)
4
P
1
2
3
4
DT
day
----
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
5
30
CH SPD
08 SP
-- --- --- --
PROG TIMER Indicator
Press PROG to end
the program.
To Enter More
Programs,
to select
press
and SET to set a
blank program
number, and then
repeat step 3.
Press PROG twice to exit this mode.
• If you’re using a cable box, make sure that it is tuned
to the desired channel and the power is left on for
timer recording.
• PROG TIMER Indicator lights up on the unit.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few
seconds to cancel the Timer
Recording.
• Any future daily or weekly recordings will
be performed as programmed.
button on the
Review, Replace or Clear
Program Contents : (Recording
is not in progress)
1
Repeat steps 1 and 2 on page 30.
Press
to select
the desired program.
2
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
3
To Replace program...
DATE
START
STOP
CH
8 SAT 9:00P 12:00A 08
TODAY
SLP
-----------------------S UR RO UND
SELE CT START DATE
SELECT :
SET
: SET
BACK :
END
: PROG
1) Press SET to
display.
to
2) Press
select and press
to set
SET or
new program
contents.
3) Press PROG.
P
1
2
3
4
SELECT
DT START STOP CH SPD
-- -- : -- -- : -- -- -8 10 : 00p 12 : 00a 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press ADD/DLT.
SELECT 1 - 8 :
ENTER : SET
END
: PROG
SET
Timer Operation
To Clear program...
ADD/DLT
PROG
STOP
4
Press PROG twice to exit this mode.
Notes
• 2 minutes before Timer recording is performed, “PLEASE
PREPARE FOR TIMER REC” appears and/or the PROG
TIMER Indicator flashes. Be sure a cassette with record
tab is loaded and the unit is in Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up during a
normal recording or One Touch Recording (page 18), the
Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been set,
check all entries and make necessary corrections.
31
Cable Box Universal Remote Control Feature
Universal Remote Control is...
The Remote Control may be set up to control some basic
DSS or Cable box functions.
The Universal Remote Control Setup
1
Find your DSS box or Cable box Brand Code
Number from one of the charts on the next
page.
POWER
2
Set up remote. Hold down DSS CABLE and
press NUMBER keys to enter code.
DVD
• If code number is 100 or greater, e.g., press 1 - 0 - 2 for
102.
DSS CABLE
FM
S UR RO UND
3
Confirm code entry. Press POWER* to turn
selected unit ON or OFF.
TV-VCR
• See below for controllable functions in each mode.
NUMBER
keys
Notes
• Please repeat the Universal Remote Control Setup after
replacing remote control batteries.
• The remote control will not operate all DSS receivers or Cable
Boxes made by the manufacturers listed. If you get no results,
your particular brand cannot be controlled.
ENTER
Using the Universal Remote Control
(Available Buttons / Functions)
Once the remote control has been properly set up, you can
select TV-VCR, FM, DVD, DSS or CABLE mode depending
on which functions you wish to control.
Press , FM, DVD or DSS CABLE on the remote
control to select the desired mode. (See below for buttons
available in each mode.)
Set to
, FM, DVD:
All TV functions, as well as functions of TV-VCR, FM, or
DVD.
Set to DSS CABLE:
• Basic VCR functions, e.g. PLAY, REC, etc.
• CABLE/DSS function, e.g. POWER, ENTER, NUMBER keys
(except 100 key), CH UP/DOWN.
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
button on the remote and try the button again.
, DVD, FM
DSS Brand Code Numbers
Toshiba.................................................................90
Hitachi/ Hughes..............................................91, 99
Primestar..............................................................92
Drake....................................................................93
Magnavox.......................................................94, 95
Uniden............................................................94, 95
Optimus..........................................................94, 95
Panasonic ............................................................96
ProScan ...............................................................97
RCA......................................................................97
SONY ...........................................................98, 105
Cable Box Brand Code Numbers
Oak Sigma .....................................46, 11, 129, 101
Panasonic ..................................17, 16, 08, 87, 109
Philips.....................23, 24, 20, 13, 07, 50, 128, 129
Pioneer.....................................................06, 05, 12
Pulsar .....................04, 42, 63, 44, 30, 52, 124, 126
Quest........................................................06, 05, 12
Radio Shack...............................44, 51, 75, 59, 126
RCA............................................17, 16, 08, 87, 109
Realistic......................................44, 51, 75, 59, 126
Recoton......................................44, 51, 75, 59, 126
Regal..................41, 14, 15, 28, 102, 104, 103, 130
Regency .................................................28, 29, 130
Rembrandt .......44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ......................................42, 06, 32, 05, 40
Scientific Atlanta.....................08, 09, 25, 61, 53, 87
Sheritech..............................................................27
Signal ...........................................................26, 112
SL Marx ................ 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ........................................ 17, 16, 08, 87, 109
Standard Components ................. 32, 39, 42, 44, 126
Stargate ................. 04, 42, 32, 40, 63, 44, 30, 52, 06,
124, 126
Sylvania..........................................................19, 18
Teknika ...........................................................74, 35
Telecaption ...................................................77, 127
Teleview..................................40, 19, 38, 32, 42, 06
Texscan ..........................................................19, 18
Tocom...................................34, 33, 01, 42, 66, 120
Toshiba.................................................................36
Unika ............................44, 42, 63, 29, 01, 126, 120
Universal ..............................52, 43, 44, 63, 42, 126
Viewstar ...................62, 40, 22, 13, 58, 20, 26, 107
Videoway..........................................07, 23, 50, 129
Vidtek ...................................................................64
Zenith ...............................................07, 23, 50, 129
Notes
Advanced Operation
Archer .............................44, 06, 01, 120, 05, 63, 126
Cableview ........... 29, 09, 01, 63, 120, 44, 42, 30, 52,
04, 124, 126
Citizen ....................44, 52, 30, 63, 42, 04, 124, 126
Curtis......................................08, 09, 25, 61, 53, 87
Century ......................................44, 51, 75, 59, 126
Cabletenna...................29, 09, 01, 63, 120, 44, 126
Cable Cinema..................29, 09, 01, 63, 120, 44, 126
Diamond .........................29, 09, 01, 63, 120, 44, 126
Eagle .........................62, 40, 22, 13, 58, 20, 26, 107
Eastern ................................................... 28, 29, 130
Explorer ................................... 08, 09, 25, 61, 53, 87
Gemini .................................................... 30, 04, 124
General Electric....................................... 01, 57, 120
General Instruments............ 01, 84, 83, 34, 03, 02, 04,
55, 65, 66, 67, 68, 120, 106,
121, 122, 115, 117, 118, 124
Gerrard ................................................44, 51, 75, 59
GC Electronics ................44, 42, 63, 29, 30, 52, 04,
124, 126
Hamlin ................41, 14, 15, 28, 102, 104, 103, 130
Hitachi ..................................................................31
Jerrold ...............01, 84, 83, 34, 03, 02, 04, 55, 65, 66,
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ...................................................... 30, 04, 124
Macom..................................................................31
Magnavox ..................................................... 26, 112
Matsushita ................................... 17, 16, 08, 87, 109
Movietime ........................ 32, 39, 42, 44, 126, 38, 40
Maestro........................................................... 74, 35
NEC.....................................................40, 19, 38, 32
NSC.....................................................40, 19, 38, 32
Novavision ............................... 08, 09, 25, 61, 53, 87
Next Level....................01, 84, 83, 34, 03, 02, 04, 55,
65, 66, 67, 68, 120, 106, 121, 122
Oak.................................................46, 11, 129, 101
• In DSS or CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.
• In DSS or CABLE mode, POWER, CH Up/Down, NUMBER Keys, ACTION, PROG, DISPLAY/ENTER,
SEARCH/SKIP- | , R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+
, COUNTER RESET/ZOOM, ANGLE,
AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are not available. Press
, FM, DVD to use these functions.
• Depending on your DSS receiver or Cable box brand, some of the functions listed may not be remote controllable.
• Some DSS receiver or Cable box brands require you to turn on the power manually.
• Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does
not respond to the first code, please try the next one.
|
33
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are
made, program index and information are also included. These index marks can be used to access or
scan recordings.
Index Search
Go directly to the desired recording.
1
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
EX I T : SEARCH
Press SEARCH*
in Playback or
Stop mode to
display INDEX
SEARCH screen,
and then press
NUMBER keys to
select the
recording number.
• To calculate
number, see below.
REW
FF
Press FF or REW to start search.
2
FORWARD SEARCH : FF
REVERSE SEARCH : REW
S UR RO UND
Playback begins
at search end. To
search forward
or back 1 index,
press FF or REW
while screen left
is displayed (10
seconds).
I NDEX SEARCH
To cancel, press PLAY.
NUMBER
keys
SELECT
SET
■ To calculate the Index Number
Example 1:
REW
FF
To go to rec. 2 from rec. 4, enter 3 and press
REW.
1
2
3
4
5
6
7
SEARCH
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
3
4
5
6
7
NOTE: indicates start points of each recording.
34
Note
• If Index Search is started very close to an index
mark, that index mark may not be counted in
the search.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
button on the
Repeat Play
Set to see a recording over and over.
PLAY
REPEAT ON
To turn “ON,”
press PLAY/REPEAT on the unit repeatedly
in Playback mode to select “REPEAT ON.”
To turn “OFF,”
repeat above to select “REPEAT OFF.”
PLAY/REPEAT
• Playback repeats when tape end is reached or
an unrecorded portion longer than 30 seconds is
detected.
Note
• For repeat play in DVD mode, see page 55.
Advanced Operation
35
Tape Operation (continued)
Zero Search
To quickly return to a specific tape counter
location.
1
2
Press DISPLAY* during playback to
display the Counter.
PLAY 12 : 00 PM
0 : 00 : 00
SLP
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
3
Continue playback, rewind, or fast
forward.
4
Press STOP.
5
Press CM/ZERO in stop mode to start
ZERO SEARCH.
• Unit goes into FF or REW mode and stops at the
last point the Counter was set to 0:00:00.
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
button on the
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV mode (Only when Weak Signal
Display is set to OFF.), DVD stops, or blank tape is played
for 5 minutes.
➞ Power turns off
• This feature is canceled if any button is pressed during above
conditions.
■ Auto Playback
Insert a tape in Power off mode
➞ Power turns on
• Playback begins if tape has no record tab.
■ Auto Rewind (except for Recording)
Tape reaches its end
➞ Rewind, ➞ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
➞ Rewind, ➞ Stop, ➞ Eject
Commercial Skip
By pressing the CM/ZERO button in Playback mode you
can skip over 1 to 3 minutes of recorded tape in just a few
seconds.
Press CM/ZERO repeatedly to select skip time in
Playback mode.
• No indication appears.
1st Press
1 min skip
2nd Press
2 min skip
3rd Press
3 min skip
Advanced Operation
OFF
37
Special VCR Features
Weak Signal Display Feature
When “ON” is selected, the picture is displayed
even when a broadcast signal is weak or
non-existent.
1
Press ACTION* to display MAIN MENU.
2
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
1
CH
SET : SET
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
: SET
END
: ACT I ON
to
select “CH.”
2) Press SET to
display SET
UP CHANNEL
screen.
1) Press
to
select WEAK
SIGNAL
DISPLAY.
2) Press SET to
set “ON” or
“OFF.”
S UR RO UND
3
It is necessary to enter TV
before
mode by pressing
selecting “CH” on the MAIN
MENU.
1) Press
M A I N MENU
DVD
Check List
ADD/DLT
SELECT
SET
Notes
• “ON” = Picture is displayed regardless of signal
condition, and may not always be clearly
visible.
“OFF” = Screen turns solid blue when signal is absent
or weak.
• If unit is connected to equipment which has blue back
feature, selecting “ON” will have no effect on the other
equipment.
4
38
ACTION
Press ACTION twice to return to the
normal screen.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
button on the
VCR Lock
All operations are prohibited except Timer
recording and tape eject. Useful for families with
small children.
VCR LOCK ACT I VATED
In Stop mode, hold
down REC on
the unit without a
cassette inserted for 7
seconds to turn “ON.”
(Please ignore “NO
CASSETTE” warning.)
Repeat above with or
without cassette to turn
“OFF.”
VCR LOCK OFF
• VCR Lock is canceled automatically after about 24
hours if clock is set.
Advanced Operation
39
V-Chip Control Feature
V-Chip Control Feature is...
Process of V-Chip Control Feature
This unit has a built-in V-Chip Control which allows you
to block unwanted TV usage based on US MOVIES and
US TV PROGRAMS Ratings.
Enter Code
Setup
Blocking
Enter Secret Code
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
Press ACTION* to display MAIN MENU.
2
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
3
1
CH
1) Press
to
select “LOCK.”
2) Press SET to
display LOCK
screen.
SET : SET
LOCK
ENTER 4-D I G I T CODE
-BACK SPACE:
ENTER : 0 - 9
END
: ACT I ON
1) Press NUMBER
keys to enter your
secret code.
2) Enter same
code again for
confirmation.
• Step 2) not necessary when changing rating or
secret code.
• Take care that you are not observed entering the
secret code.
To Make Corrections
Press repeatedly to move the cursor.
Press NUMBER keys to make the correction.
4
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE : SET
END
: ACT I ON
Press SET to display
US Ratings menu
(see pages 41-42).
Or
Press ACTION twice
to exit.
Changing your secret code
• You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR to clear
current code.
Repeat steps 3 and 4 to enter new code.
40
• Some rental movies do not include V-Chip
data.
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes or
programs cannot be accessed unless the
secret code is entered.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
If LOCK menu is not displayed, perform “Enter
Secret Code” steps on page 40.
US MOVIES Ratings
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
to select
US MOVIES.
2) Press SET to set
“ON” or “OFF.”
• “NEXT PAGE” displays CANADIAN V-Chip
setting menu. Not necessary except when viewing
Canadian tapes or broadcasts.
2
3
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
to
select CHANGE
SETTINGS.
2) Press SET to
display screen.
Setup
Blocking
US MOVIES RATINGS
G
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable
for children.
PARENTS CAUTIONED:
PG-13 Some material may be inappropriate
for children under 13.
R
NC-17
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
No one 17 and under admitted.
ADULTS ONLY:
1) Press
to
select VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
Press
to select
and SET to set
ratings to be blocked.
(See ratings chart on
this page.)
Advanced Operation
5
Enter Code
X
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign
movies usually have no ratings.
4
Process of V-Chip Control Feature
PG
■ “ON” ➞ V-Chip Control is activated.
■ “OFF” ➞ V-Chip Control is deactivated.
Note
button on the
Press ACTION to redisplay LOCK
menu and continue with US TV
PROGRAMS Ratings Setup (page 42).
Or,
press ACTION three times to exit.
41
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do “Enter
Secret Code” steps on page 40.
Process of V-Chip Control Feature
US TV PROGRAMS Ratings
US TV PROGRAMS RATINGS: Chart 1
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
* to
select US TV
PROGRAMS.
2) Press SET to set
“ON” or “OFF.”
■ “ON” ➞ V-Chip Control is activated.
■ “OFF” ➞ V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
2
3
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET : SET
END
: ACT I ON
1) Press
to
select CHANGE
SETTINGS.
2) Press SET to
display screen.
1) Press
to
select VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports, weather,
bulletins, emergency information usually have no
ratings.
4
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET : SET
END
: ACT I ON
Press
to select
and SET to set
ratings to be blocked.
(See ratings charts on
this page.)
• Ratings highlighted in
green will be blocked.
Ratings in white letters
will not be blocked.
Note
• You may select from standard TV ratings (chart 1), or
customize to a specific content rating (chart 2).
5
42
Enter Code
Setup
Blocking
TV-Y FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
TV-Y7 FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
TV-G GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
TV-PG PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
TV-14 PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language,
and more intense violence.
TV-MA MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and
sexual situations.
US TV PROGRAMS RATINGS: Chart 2
FV
Fantasy Violence
V
Violence
S
Sexual Situations
L
Adult Language
D
Sexually Suggestive Dialogue
Press ACTION three times to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
button on the
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
CH08
PROGRAM RAT I NG EXCEEDED
S UR RO UND
RAT I NG : PG-1 3
ACCESS CODE
----
• If a program or movie
exceeds the ratings you
have set, a message
will appear on a black
background and sound is
muted.
ENTER : 0-9
To View a Blocked Program/Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in the
Blocking Message screen.
SELECT
SET
ACTION
• V-Chip Control is reactivated when power is turned off
or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-3 page 40). Then,
set US MOVIES and/or US TV PROGRAMS to
and SET. (Ratings set on pages
“OFF” using
41 and 42 is retained and will be in effect when
V-Chip Control is activated again.)
Advanced Operation
43
Audio Features
Audio Mode for Playback
Choose the type of sound track for playback.
1
2
See the “Playback a Tape” section on page
18 to playback the tape.
H I F I ( L/R)
H I F I ( L)
H I F I ( R)
NORMAL
Press AUDIO*
repeatedly (each press
within 5 seconds) to
select desired mode.
With the proper audio mode
setting, your unit can:
• Record and playback MTS stereo broadcast
(main language) in stereo Hi-Fi. Stereo sound is
recorded on the left and right audio tracks and
on the video portion of a tape.
• Record and playback a monaural broadcast
(main language) or SAP (Secondary Audio
Program, usually in a second language) on the
Hi-Fi tracks for better quality monaural sound.
• Playback non-Hi-Fi tapes in monaural.
• Select “HIFI (L/R),” “HIFI
(L)” or “HIFI (R)” to listen
to stereo recordings in
stereo sound. Select
“NORMAL” for monaural
sound.
VOL +/S UR RO UND
• This screen appears when you press AUDIO during
playback.
MUTE
SURROUND
Audio Mode for Recording
Choose audio mode to match recording type.
1
Press AUDIO repeatedly to select the audio
mode according to the type of broadcast to be
recorded.
• The Audio mode selected stays in effect until it is
changed.
2
AUDIO
SELECT
SET
ACTION
See the “Record On a Tape” section on page
18 to do a recording.
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true
stereo sound. Standard stereo tapes will playback with
monaural sound.
• To listen to Hi-Fi stereo playback, the unit AUDIO (L/R)
jacks must be connected to a stereo amp and speakers.
• There may be a difference in audio level between Hi-Fi
and normal audio playback.
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
DVD Volume Adjust
Some DVDs are recorded in lower average volume
level. For these DVDs, this unit can be set so that
the average volume is increased automatically.
1
2
Press ACTION to display MAIN MENU.
1) Press
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
SET : SET
to
select “TV.”
2) Press SET to
display SET UP
TV screen.
button on the
V.S.S. (Virtual Surround Sound)
[DVD only]
Enjoy a surround-like effect if you are using two
front speakers only. The effect is broadened
and sound seems to come from virtual speakers
on either side if the disc has surround signals
recorded on it.
Press SURROUND in DVD mode.
• The Surround sound effects can be changed by
pressing SURROUND repeatedly as shown by the
figure below.
VSS OFF
3
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
SELECT :
END
: ACT I ON
4
SET : SET
1) Press
to
select DVD
VOL ADJUST.
2) Press SET to
set the level (0,
+1, or +2).
Default
VSS1
Press ACTION twice to return to the
normal screen.
VSS2
Surround Sound System
VSS3
SURROUND ON
SURROUND OFF
Press SURROUND.
• “SURROUND ON” is
displayed.
To Cancel,
press SURROUND.
Notes
Advanced Operation
You can hear a deeper, 3-D sound effect using
just the unit’s two front speakers.
• V.S.S. effects is available in DVD mode only.
• Turn off the surround effects on the other equipment.
• V.S.S. will not work, or will have less effect, with some
discs.
• Turn V.S.S. off if it causes distortion.
Notes
• Surround sound effect is not available for normal
(mono) broadcasts.
• The surround effect (TV, VCR mode only) is not
output to Audio Output L/R Connector.
45
Video/Audio Menu
This feature allows easy setting of picture and sound suitable for each program source.
Audio Menu
Video Menu
1
2
Press ACTION* to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
3
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
SET UP TV
4
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to
select “VIDEO
MENU.”
2) Press SET
repeatedly to
select desired
mode. (See
below.)
Press ACTION three times to end setup.
Do steps 1 - 3 left.
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
SELECT :
END
: ACT I ON
5
1
CH
CLOCK
1) Press
to select “TV.”
2) Press SET to
display SET
UP TV screen.
a
b
c
1) Press
to
select “AUDIO
MENU.”
2) Press SET to
select desired
mode. (See
below.)
Press ACTION three times to end setup.
[Audio Menu]
■ NORMAL
■ AUTO
[Audio AGC (Auto Gain Control)]
The sound level is automatically adjusted to suit
the program source (see below left).
■ MOVIE
Sound suited to movies.
■ MUSIC
Sound suited to music. (Factory setting)
■ SPEECH
Sound suited to dialogue.
[Video Menu]
■ NORMAL
Factory setting.
■ MOVIE
Picture is adjusted for a movie-like feel.
■ NIGHT
Color and picture intensity are adjusted to be
easier on the eyes for night viewing.
Volume level
High
Standard
TV
Volume level
High
CD
TV
Low
Standard
TV
TV
Low
AUDIO MENU : NORMAL
AUDIO MENU : AUTO
<Audio AGC Example>
46
CD
• The effects of this feature on the signal is not output
to the Audio/Video Output Connector.
• When AUDIO MENU mode is “AUTO,” the AUDIO
ADJUST setting will be “STANDARD.”
• AUDIO MENU settings remain in memory.
• VIDEO MENU settings do not remain in memory.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Video/Audio Adjustment
*Important: If a remote control button does not work when pressed, press the
and try the button again.
Audio Adjustment
Video Adjustment
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
3
SET UP TV
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
5
V I DEO ADJUST
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
M A I N MENU
DVD
LOCK LANGUAGE
53
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
c
d
SET UP TV
1) Press
to
select an item.
(See below.)
2) Press
to
adjust.
e
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
AUDIO ADJUST
BASS
TREBLE
BALANCE
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
f
Press ACTION four times to end setup.
[AUDIO Adjustment]
■ COLOR Control
■ BASS Control
■ TINT Control
Adjust for natural flesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by adjusting both
contrast and color level in the proper balance.
1) Press
to
select an item.
(See below.)
2) Press
to
adjust.
To Reset AUDIO Controls,
and SET to select and set
press
“STANDARD.” All controls return to their factory
settings.
[VIDEO Adjustment]
Adjust color intensity.
1) Press
to
select “AUDIO
ADJUST.”
2) Press SET to
display.
Advanced Operation
Press ACTION four times to end setup.
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
SELECT :
END
: ACT I ON
1) Press
to
select “VIDEO
ADJUST.”
2) Press SET to
display.
1
CH
CLOCK
SELECT :
END
: ACT I ON
To Reset VIDEO Controls,
and SET to select and set
press
“STANDARD.” All controls return to their factory
settings.
6
Press ACTION to display MAIN MENU.
TV
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
1) Press
to select “TV.”
2) Press SET to
display SET
UP TV screen.
a
b
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
REMOTE WARNING : ON
SELECT :
END
: ACT I ON
4
1
CH
CLOCK
button on the remote
To adjust the intensity of low frequency sound.
■ TREBLE Control
To adjust the intensity of high frequency sound.
■ BALANCE Control
To adjust the (L/R) unit speaker output level.
• The levels set here do not affect other audio
equipment when connected to the Audio Output
L/R Connector.
■ SHARPNESS Control
Adjust picture sharpness.
47
Disc Operation
Subtitle Language (DVD only)
You can select a different subtitle language (if offered)
than the one set at the Settings for DVD Operation. (See
page 60.)
Press SUB TITLE* in
Play mode to display
the subtitle selection
on-screen.
1
Check List
Please read “Basic DVD Operation” on
page 20.
[Subtitle language]
[Audio soundtrack language]
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS
JPN
CHI
KOR
MAL
VIE
THA
• Display disappears
after 5 seconds.
• When no subtitles
are offered, “-” will be
displayed instead of
the language number.
2
Te amo
1) Press
to select
desired language.
2) Press (or )
to select “ON” or
“OFF.”
Number of subtitle language being played back.
Notes
• When closed captioning is used along with subtitles, they may
overlap. If so, turn one function off. (See pages 24 and 25.)
• If after several presses of the button the language does not
change, language selection is not offered on the disc.
• Subtitles may not change to the selected language
immediately.
• When disc is removed, subtitles revert to initial setting
language. If the initial language is not recorded on the disc,
the disc’s priority language will appear.
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Other
• Change the No. by pressing
SET.
, and press
Audio Soundtrack Language (DVD only)
You can change the audio soundtrack language,
selected at the Settings for DVD Operation, to a
different language if available. (See page 60.)
(This operation works only with discs on which multiple
audio soundtrack languages are recorded.)
a
AUDIO: 1 ENG
Dolby Digital 3/2.1ch
Hello
SELECT :
END
: AUDIO
Press AUDIO in
Play mode to display
the audio selection
on-screen.
• Display disappears after
5 seconds.
Audio attribute 1 type,
sampling frequency, bit
No. of the disc.
b
AUDIO: 3 ESP
Dolby Digital 3/2.1ch
Press
to select
desired language.
Hola
SELECT :
END
: AUDIO
48
Audio soundtrack
language being played
back.
[Audio attribute 1 type, sampling
frequency, bit No. of the disc (see
page 61)]
96 kHz
LPCM
or
48 kHz
16 bit
20 bit Linear PCM disc
24 bit
Dolby
Digital
1 ch - 5.1 ch
Dolby Digital disc
dts
1 ch - 5.1 ch
dts disc
Notes
• If, after several presses of the AUDIO button the
language does not change, language selection is
not offered on the disc.
• When disc is removed, language reverts to initial
setting. If this language is not recorded on the disc,
the language recorded will be heard.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
appears on the screen while a
When
button is being pressed, it means that the
corresponding operation is prohibited by
the unit or the disc.
Multiple Angle Viewing (DVD only)
DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at different
angles. You can view these angles, if available, using the
ANGLE button.
Press ANGLE in Play
mode to display the angle
selection on-screen.
1
• Display disappears after 5
seconds.
Press
to select the
desired angle.
2
ANGLE Indicator
Number of angle being played back.
• ANGLE Indicator lights up on the unit when
a scene recorded at different angles is
detected.
• The angle number can be set beforehand
so that the angle is switched whenever
ANGLE Indicator lights up.
Vocal selection for Karaoke discs (DVD/Video CD)
a
b
Press AUDIO in Play mode to display the audio
screen.
1) Press
(or
) to
select as shown below.
2) Press (or ) to set.
(DVD only)
SELECT :
END
: AUDIO
You can enlarge specific portions of a picture and select the
zoom ratio using the ZOOM button on the remote during
DVD playback.
Set Zoom size.
Press ZOOM repeatedly to change display as follows.
• Closed captioning will not be displayed
while Picture Zoom is used. To see
subtitles, set the subtitle feature to ON (see
page 48).
• The subtitle cannot be enlarged nor can it’s
position be changed.
• The picture zoom feature does not work
with a Video CD.
• During picture zoom, “ZOOM1” or “ZOOM2”
appears on-screen for 5 second.
• Zooming, on some discs, may result in poor
picture quality, or may not operate at all.
Advanced Operation
Picture Zoom (DVD only)
• You can enlarge the center portion of the image to one of 2
magnifications.
X 1.0 (ORIGINAL)
X 1.5 (ZOOM 1)
1st press
X 2.0 (ZOOM 2)
2nd press
ZOOM 2
ZOOM 1
3rd press
■ Use the , , and buttons to move the
position up, down, left and right.
49
Disc Operation (continued)
Title menu (DVD only)
Some DVDs have more than one title, e.g. movies. If
the disc offers a title menu, you can select the desired
title number. (Operation may vary according to the disc.)
1
T I TLE MENU
Cas t l es
Love r s
B i r ds
S UR RO UND
Dogs
Press TITLE* in Play
mode to display title
screen.
<Example>
2
T I TLE MENU
Dogs
Cas t l es
Love r s
B i r ds
B i rds
of the world
1) Press
or
NUMBER key(s) to
select a title.
2) Press SET or
PLAY to start play.
• Step 2) not necessary
when using NUMBER
key(s).
NUMBER
keys
CLEAR
TITLE
DISPLAY
MENU
SELECT
SET
ACTION
PLAY
STOP
<Example>
DVD menu (DVD only)
DVDs may offer a special menu. This menu may
include guides to unique contents, audio/subtitle
languages, etc. Although contents and operation may
vary, the following steps show basic steps for using the
menu.
a
DVD MENU
1 . SUBT I TLE
2 . AUD I O
Press MENU in Play
mode to display DVD
menu.
3 . ANGLE
<Example>
b
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
1) Press
or
NUMBER key(s) to
select an item.
2) Press SET or
PLAY to access.
• Step 2) not necessary
when using NUMBER
key(s).
Repeat step “b” if there is more than one menu.
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
remote and try the button again.
Program Play (Video CD/CD)
Check List
Unit is in TV-VCR mode, press
Video CD or CD is inserted.
You can program specific tracks and order of
play.
1
2
Press ACTION in Stop mode to display MAIN
MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
3
SET : SET
DVD MAIN MENU
4:3 Pan & Scan
SELECT
SET
END
4
1 6
2 7
3 8
4 9
5 10
PROGRAM PLAY
DISC
PROGRAM
11 16
5 8
12 17
15 6
13 18
1 13
14 19
3 2
15 20
2
Press DISPLAY to display Disc
Information screen.
(Disc Information Screen)
TRACK
PBC
START
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
START
: SET
VIDEO CD
1 : 35 : 12
NEXT : DISPLAY
Press DISPLAY again to display Unit
Information screen.
d
Press SET to enter Select mode.
Cursor move to “OFF.”
(Unit Information Screen)
SET
e
1) Press
to
select “START.”
2) Press SET to start
play of programs
in the sequence
selected.
Press
: SET
END : DISPLAY
to select “DISC.”
(Unit Information Screen)
PLAY
REPEAT: DISC
PROGRAM PLAY
SELECT :
SET
: SET
END : DISPLAY
•To cancel, press STOP during play, then press CLEAR.
Notes
• Up to 15 tracks can be programmed.
• “ ” or “ ” (depending on disc) indicates additional
for next or
PROGRAM PLAY screen. Press
previous screen.
• To clear the last program one by one,
to move to “CLEAR LAST” and press
Press
SET. (Pressing CLEAR also clears last program.)
• To clear all programs,
to move to “CLEAR ALL” and press SET.
Press
(Programs are also cleared when the power is turned off or the
disc is removed.)
f
Advanced Operation
PROGRAM PLAY
DISC
PROGRAM
11 16
5 8
12 17
15 6
13 18
1 13
14 19
3 2
15 20
2
: 1
: OFF
c
1) Press
to select a track
number. (Track
numbers on disc
are displayed.)
2) Press SET to set.
•Repeat step 5 to select another track.
•The selected track is added on the right side.
6
Do steps 1 through 6 on this page.
SET
:
: SET
: ACTION
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
1 6
2 7
3 8
4 9
5 10
a
b
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
1) Press
to
select “PROGRAM
PLAY.”
2) Press SET to
display screen.
.
Program Repeat Play
(Video CD/CD)
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
5
CH
CLOCK
SELECT :
END
: ACT I ON
1
1) Press
to
select “DVD.”
2) Press SET to
display screen.
, DVD button on the
Press SET to set mode. Cursor
move to “REPEAT.” To cancel, select
“REPEAT: OFF” in step e, then press
SET.
51
Disc Operation (continued)
Random Play (Video CD/CD)
Tracks are played in a random order.
1
2
Press ACTION* in Stop mode to display
MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
3
4:3 Pan & Scan
4
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
1) Press
to select “DVD.”
2) Press SET to
display screen.
SET : SET
DVD MAIN MENU
SELECT
SET
END
If a remote control button
does not work when pressed,
, DVD button on
press the
the remote and try the button
again.
CH
CLOCK
SELECT :
END
: ACT I ON
1
*Important:
1) Press
to select
“RANDOM PLAY.”
2) Press SET to begin
random play.
:
: SET
: ACTION
• To cancel, press STOP during play, then press CLEAR.
52
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD Operation using On-Screen Displays
When DISPLAY is pressed, On-Screen Displays show disc
information (title/chapter/track number, elapsed playing
time) and unit information (Repeat Play, Play mode).
1
Press DISPLAY in Play or Stop mode to display
“On-Screen Display.”
• Each press of DISPLAY changes the on-screen display
as follows. (Please refer to page 54 or 55.)
• DISPLAY button does not function while DVD TITLE MENU
is displayed.
2
1) Press
(or
) to select an item.
2) Press SET to set.
3
1) Press
to select the setting.
2) Press SET to set.
<Example of DVD>
T I TLE
: 12
CHAPTER : 11
DVD
0 : 12 : 34
T I TLE
: 12
CHAPTER : 24
NEXT : DISPLAY
SELECT :
SET
: SET
NEXT : DISPLAY
<Example of Video CD>
TRACK
PBC
: 12
: OFF
TRACK
PBC
SET
: 17
: OFF
: SET
SET
: SET
VIDEO CD
0 : 12 : 34
VIDEO CD
0 : 12 : 34
NEXT : DISPLAY
To return to the
normal screen,
press CLEAR or
DISPLAY repeatedly.
• When DISPLAY is pressed during
play of a Video CD with Play control,
the NUMBER keys are not available
on the displayed screen. In this case,
press DISPLAY again to remove the
displayed screen.
• When appears on the screen while
a button is being pressed, it means
that the corresponding operation is
prohibited by the unit or the disc.
Advanced Operation
SELECT :
SET
: SET
DVD
0 : 12 : 34
NEXT : DISPLAY
53
DVD Operation using On-Screen Displays (continued)
Detailed Descriptions of Each On-Screen Display
Disc information screen (for DVD)
1. TITLE No.
• Select “TITLE,” and press SET*.
• Change the No. by pressing
or NUMBER keys, and
press SET.
1
2
T I TLE
: 1
CHAPTER : 12
DVD
1 : 12 : 55
3
4
2. Chapter No.
• Select “CHAPTER,” and press SET.
• Change the No. by pressing
or NUMBER keys, and
press SET.
SELECT :
SET
: SET
3. Disc currently being played
4. Elapsed playing time
T I TLE
: 1
CHAPTER : 12
The screen may be changed by selecting the elapsed time.
• Select the elapsed playing time (“xx:xx:xx”), and press SET.
• Change the elapsed time by pressing NUMBER keys.
Hours ➞ Minutes ➞ Seconds are entered in order.
If the time entered is not on the disc, the entry will have
no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
SELECT :
SET
: SET
NEXT : DISPLAY
DVD
1 : --: --
NEXT : DISPLAY
If SET is pressed while
making entries, unit returns
to the condition before
entries were made.
Hour Minutes Seconds
• This function does not work with some discs.
Disc information screen (for Video CD/ CD)
A. Track No.
• Select “TRACK,” and press SET.
• Change the No. by pressing
or NUMBER keys, and
press SET.
A
B
TRACK
PBC
: 1
: OFF
VIDEO CD
1 : 35 : 12
C
D
B. Playback control ON/OFF
[Video CD with playback control only]
SET
ON
OFF
C. Disc currently being played
Video CD
: SET
NEXT : DISPLAY
Video CD menu play is displayed.
Video CD menu play is not displayed.
CD
NUMBER
keys
D. Elapsed playing time
Notes
• Track No. and elapsed playing time are not displayed during
play started from menu of Video CDs with playback control.
• When appears on the screen while a button is being pressed,
it means that the corresponding operation is prohibited by the
unit or the disc.
54
SELECT
SET
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
Detailed Descriptions of Each On-Screen Display
Unit information screen
• Select “REPEAT”, and press SET.
• Change the desired mode during play by pressing
, and press SET.
a. Repeat Play
DVD
Video CD/CD
CHAPTER REPEAT
TRACK REPEAT
TITLE REPEAT
DISC REPEAT
REPEAT OFF
REPEAT OFF
PLAY
REPEAT : CHAPTER
a
SET
: SET
END : DISPLAY
b. Play mode [Video CD/ CD only] (See page 51 or 52.)
PROGRAM PLAY
RANDOM PLAY
----
program play
random play
normal play
PLAY
REPEAT : DISC
RANDOM PLAY
b
SET
: SET
END : DISPLAY
• CHAPTER/TITLE REPEAT PLAY (DVD)
CURRENT PLAYBACK POSITION
• TRACK/DISC REPEAT PLAY (Video CD/CD)
CURRENT PLAYBACK POSITION
TITLE
chapter
track
chapter
chapter
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
track
Advanced Operation
For your reference
track
TRACK REPEAT
DISC REPEAT
NORMAL PLAY
• For repeat play in VCR mode, see page 35.
55
MP3/WMA/JPEG Playback Operation
This unit can play MP3/WMA/JPEG
format CD-R or CD-RW recorded for
personal use on a PC, etc.
Some discs may not play due to
recording condition.
1
2
3
ROOT
My favorite
Press POWER* on the
remote or unit.
Press OPEN/CLOSE,
and then place an
MP3/WMA/JPEG disc
into the disc tray. Press
OPEN/CLOSE to close.
• MP3/WMA/JPEG menu
is displayed.
• Playback starts
automatically (except
JPEG files).
• CD directory is displayed.
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
TECHNO
picture1.jpg
picture2.jpg
picture3.jpg
picture4.jpg
POPS
Example: If the CD-R/CD-RW
file hierarchy is displayed on the
PC as shown in diagram at left,
MP3/WMA/JPEG Menu Screen,
like the one below is displayed.
Note
• File names are displayed in
ascending order (1, 2, 3...9, A, B,
C...Y, Z) in the MP3/WMA/JPEG
MENU Screen ROOT.
JAZZ.wma
MP3/WMA/JPEG MENU SCREEN
Function
Status
Folder area
(Current folder
appears green.)
ROOT
My favorite
TECHNO
POPS
JAZZ
..
CAR1
CAR2
END_WALTZ
PICTURES
PLAY MODE : NORMAL
4
Press
to move cursor to
File area or PLAY MODE.
(In STOP mode)
■ File area Operation
(In STOP mode)
Press
to select items and SET
or PLAY to start.
| (next) or
Press SKIP+
(previous) to skip a
SKIP- |
file/folder page (7files) in the File area.
Select an MP3/WMA file ( / ).
MP3/WMA Playback (See next page)
Select an JPEG file ( ).
JPEG Playback (See next page)
Select a folder ( ).
Display files/folders contained in the
folder.
Select a Parent folder ( ).
Make changes to the previous
directory display.
Counter
00 : 00 : 00
PLAY
PLAY MODE
File area
(Selected
file/folder is
highlighted.
Titles are
displayed up to
11 characters.)
Explanation of Icons
:MP3 file
:Folder
:JPEG file
:WMA file
:Parent folder
PLAY MODE selection
PLAY
MODE:
JPEG Playback
- Slide-show All MP3/WMA files are
All JPEG files are selected
NORMAL selected and played back
and played back one time
one time only.
only.
SINGLE
The selected MP3/WMA file The selected JPEG file is
REPEAT is played back repeatedly.
played back repeatedly.
The MP3/WMA files
The JPEG files contained in
contained in the selected
the selected folder are played
FOLDER folder are played back
back repeatedly.
REPEAT repeatedly. However, folders However, folders below the
below the selected folder are selected folder are not played
not played back.
back.
DISC
All MP3/WMA files are played All JPEG files are played
back repeatedly.
REPEAT back repeatedly.
MP3/WMA Playback
■ Play mode Operation
(In STOP mode)
Press
to select the desired
PLAY MODE.
5
56
Press ACTION to
return to the DVD MAIN
MENU. (Press ACTION
again to return to the
MP3/WMA/JPEG MENU.)
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.
Windows Media, and the Windows logo are trademarks,
or registered trademarks of Microsoft Corporation in
the United States and/or other countries. WMA is a
compression format developed by Microsoft Corporation.
It achieves the same sound quality as MP3 with a file size
that is smaller than that of MP3.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MP3/WMA Playback
JPEG Playback
to select an MP3/WMA file
1 (Press/ ) in STOP
mode.
You can play JPEG images.
Displayable Image Size: 32x32~7680x7680 pixels
2
• Some JPEG format may not be played back.
Do steps 1~3 on page 56.
Press SET or PLAY to start playback.
■ Forward/Reverse Search
Press FF/SLOW+ or REW/SLOW- during play.
Press PLAY to release.
• Search speed, slow at first, increases with
each additional press of the button up to 5
levels.
■ Forward/Reverse Track Skip
| or SKIP- |
during play.
Press SKIP+
Each press skips a track.
• If pressed within first 3 seconds of playback,
skips to the previous track. If over 3 seconds,
only.)
returns to top of track. (SKIP- |
• Put unit in Stop mode before performing
folder/file selection (see step 4 on previous
page.)
■ Pause
Press PAUSE during play.
Press PLAY to release.
3
4
Note
1
Do steps 1~3 on page 56.
Press
to select an JPEG file (
).
00 : 00 : 00
PLAY
ROOT
My favorite
TECHNO
POPS
JAZZ
..
CAR1
CAR2
END_WALTZ
PICTURES
PLAY MODE : NORMAL
2
Press SET or PLAY. Selected file is
displayed.
JPEG Playback Screen
<Example: CAR1>
■ Next/Previous Search
| or SKIP- |
Press SKIP+
<Example>
Press STOP to stop play.
Only the JPEG
files in a folder that
were saved while
being displayed
are displayed.
ROOT
Press OPEN/CLOSE to eject the disc.
My favorite
The MP3 MENU is closed automatically.
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
Note
• Copyright protected files and files containing errors
cannot be played back. The unit skips to the next file.
picture1.jpg
<Example: CAR2>
POWER
S UR RO UND
SKIP- |
ANGLE
ACTION
PLAY
REW/
SLOWSTILL/
PAUSE
SKIP- |
SELECT
SET
STOP
FF/SLOW+
ZOOM
SKIP+
|
SKIP+
|
■ Start Slide-show
Press FF/SLOW+ or REW/SLOW-.
(see next page)
■ Enlarging an image
Press ZOOM. (see next page)
■ Rotating an image
Press ANGLE. (see next page)
■ Returned on the MP3/WMA/JPEG MENU
Press STOP. (see previous page)
3
Advanced Operation
<Example: CAR1>
OPEN/
CLOSE
Press ACTION to return to the DVD MAIN
MENU.
57
MP3/WMA/JPEG Playback Operation (continued)
JPEG Playback - Slide-show -
JPEG Playback - Zoom (During JPEG Playback.)
You can enlarge specific portions of a JPEG
picture and select the zoom ratio using the ZOOM
button on the remote during JPEG Playback.
Set Zoom size.
Press ZOOM repeatedly to change display as
follows.
Press STOP to return to the MP3/WMA/JPEG
MENU.
• You can enlarge the center portion of the image to
one of 2 magnifications.
• Operation can be done during Rotation (below).
X 1.0 (ORIGINAL)
X 1.5 (ZOOM 1)
1st press
(During JPEG Playback.)
JPEG files are displayed automatically (about
every 3 seconds) as a slide-show.
1
Press FF/SLOW+ or REW/SLOW-.
Only the JPEG files in a folder that were saved
while being displayed are displayed.
<Example>
ROOT
X 2.0 (ZOOM 2)
2nd press
My favorite
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
3rd press
■ Use the , , and buttons to move the
position up, down, left and right.
Note
TECHNO
• Position cannot be changed on X1.0 ORIGINAL
images.
picture1.jpg
picture2.jpg
picture3.jpg
picture4.jpg
REW/SLOWFF/SLOW+
JPEG Playback - Rotation (During JPEG Playback.)
You can rotate a JPEG picture using the ANGLE
button on the remote during JPEG Playback. (The
JPEG picture will be rotated 90° clockwise.)
Set rotation.
Press ANGLE repeatedly to change display
as below. (During JPEG Playback screen)
Press STOP to return to the MP3/WMA/JPEG
MENU.
<Example>
If FF/SLOW is pressed while picture 1 is displayed.
picture 1
picture 2
picture 3
picture 4
Image changes every 3 seconds.
If REW/SLOW- is pressed while picture 3 is
displayed.
picture 3
picture 2
picture 1
1st Press
4th Press
2nd Press
3rd Press
Notes
• Operation can be done during ZOOM (above).
• The vertical/horizontal ratio of rotated JPEG
images may vary when they are displayed.
58
Image changes every 3 seconds.
■ Still picture
Press PAUSE (only SLIDE)
■ Forward/Reverse Track Skip
| or SKIP- |
. Each press
Press SKIP+
skips a file.
■ Cancel slide show
Press STOP to return to the MP3/WMA/JPEG
MENU.
2
Press ACTION to return to the DVD MAIN
MENU.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Advanced Operation
59
1
Once initial settings are done, they remain
in memory (even after the power is off) until
changed. This means the unit will always
operate under the same conditions (especially
DVDs) each time.
3
DISC LANGUAGES (See below.)
Any languages offered on the disc can be set. If a
language not offered is set, the original disc language
will be selected.
AUDIO OUTPUT (See page 61.)
You can set the audio output that comes from the
digital audio output terminal.
STILL MODE (See page 62.)
Tolected at utomaticly See page 62.)
“AUDIO” selections
To select the audio soundtrack language.
(Factory preset: English)
English/Spanish/French/Japanese
Original: Original disc language
OTHER ✱✱✱✱: Other language selection*1
“SUBTITLE” selections
DISC LANGUAGES (DVD only)
To select and set the language of the audio soundtrack,
subtitles, or title/DVD menus for all discs to be played.
To select the subtitle language.
(Factory preset: AUTO)
AUTO: Same language selected for “AUDIO”
• If language set for “AUDIO” is
used in playback, subtitles will not
appear.
• If another language is used during
playback, the subtitles will appear
in the language selected at “AUDIO”
setup.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
“MENUS” selections
(Factory preset: English)
To select the language used in title menus or
DVD menus.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
To enter OTHER ✱✱✱✱ code number,
Press NUMBER keys (Please refer to
language codes on page 63).
To make corrections, press repeatedly to
delete language code number, and correct.
60
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the
on the remote and try the button again.
, DVD button
AUDIO OUTPUT
Select the digital output to be output from the optical
digital audio output connector of the unit.
1
2
Do steps 1 and 2 on page 60.
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4:3 Pan & Scan
SELECT
SET
END
LPCM(DVD)
Dolby Digital
dts
DRC
SELECT
SET
END
: OFF
: Bitstream
: Bitstream
: OFF
:
: SET
: ACTION
1) Press
to select
an item.
2) Press SET
repeatedly for
output. (See
below.)
■ “LPCM (DVD)” selections
OFF:
PCM:
Linear PCM of less than 48 kHz/16 bit
is output. When playing DVDs recorded
in linear PCM of over 48 kHz/20 bit, no
digital audio is output. (Factory preset)
When playing DVDs recorded in
linear PCM of 48 kHz/20 bit/24 bit or
more, digital audio converted to 44.1
kHz/16 bit or 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted
to48 kHz/16 bit or below for copyright
protection.)
■ “Dolby Digital” selections
■ “dts” selections
Bitstream: dts bitstream is output. (Factory preset)
PCM:
When you have connected a amplifier
that doesn’t have a built-in dts decoder.
■ “DRC (Dynamic Range Compression)”
selections
ON:
4
ACTION
Normal audio range is selected. (Factory
preset)
For dynamic sound even at low volume,
this is useful for late-night listening.
[Dolby Digital DVDs only].
Press ACTION to redisplay DVD MAIN MENU
and go to step 2 to setup another item. Or,
press ACTION three times to exit.
Type of
amplifier
to be
connected
Recommended setting
LPCM
(DVD)
Dolby
Digital
dts
AV amplifier
without Dolby
Digital/dts
decoder
PCM
PCM*1
PCM*1
AV amplifier
including
Dolby Digital
decoder
PCM
Bitstream
PCM
AV amplifier
including
Dolby
Digital/dts
decoder
PCM
Bitstream Bitstream*2
No amplifier
is connected
• Make settings according to amplifier
connected to optical audio output as shown
in above table.
Advanced Operation
Bitstream: Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
PCM:
When you have connected a amplifier
that doesn’t have a built-in Dolby Digital
decoder.
OFF:
SET
1) Press
to select
“AUDIO OUTPUT.”
2) Press SET to
display screen.
:
: SET
: ACTION
AUDIO OUTPUT
3
SELECT
*1 When connecting an amplifier (with an
optical digital input connector) which
does not contain the Dolby Digital or
dts decoder, be sure to select “PCM.”
If “Bitstream” is selected, starting DVD
play may cause such a high level of noise
as to be harmful to your ears and damage
the speakers.
*2 When a dts decoder is connected, please
select “Bitstream” in “dts.” If “PCM” is
selected, there will be stereo sound.
61
Settings for DVD Operation (continued)
STILL MODE
Set to reduce jitter in a displayed still picture or a motion
picture.
1
2
Do steps 1 and 2 on page 60.
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
1) Press
* to select
“STILL MODE.”
2) Press SET repeatedly
for mode. (See below)
S UR RO UND
SELECT
SET
END
*Important:
If a remote control button does not
work when pressed, press the DVD
button on the remote and try the
button again.
:
: SET
: ACTION
AUTO:
“FIELD” (Field still) or “FRAME” (Frame still)
is automatically selected during the still mode.
(Factory preset)
FIELD: “FIELD” (Field still) is always selected.
This setting will reduce jitter when compared
with “AUTO” on some discs.
FRAME: “FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly
when compared with “AUTO” on some discs.
SELECT
SET
ACTION
3
Press ACTION twice to exit this mode.
Selecting TV MODE
Set the screen display style for widescreen video material
playback.
a
b
Do steps 1 and 2 on page 60.
Example
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
SELECT
SET
END
1) Press
to select “TV
MODE.”
2) Press SET repeatedly
for mode. (See below.)
:
: SET
: ACTION
4:3 Pan & Scan : Widescreen video data is played in Pan
(Factory preset)
& Scan style (left and right of screen is
trimmed.)
• Video data not formatted in Pan &
Scan will play in letterbox style.
4:3 Letterbox : Widescreen video data is played in
Letterbox style (top and bottom of
screen has black margin).
c
62
4:3 Pan & Scan (Factory preset)
4:3 Letterbox
Press ACTION twice to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Language Code List
Enter the appropriate code number for the initial settings “AUDIO,” “SUBTITLE” and/or “MENUS” (see
page 60).
Code Language
Code Language
Code Language
Code Language
7079 Faroese
7678 Lingala
8375 Slovak
6566 Abkhazian
7082 French
7679 Laothian
8376 Slovenian
6570 Afrikaans
7089 Frisian
7684 Lithuanian
8377 Samoan
6577 Ameharic
7165 Irish
7686 Latvian, Lettish
8378 Shona
6582 Arabic
7168 Scots Gaelic
7771 Malagasy
8379 Somali
6583 Assamese
7176 Galician
7773 Maori
8381 Albanian
6588 Aymara
7178 Guarani
7775 Macedonian
8382 Serbian
6590 Azerbaijani
7185 Gujarati
7776 Malayalam
8385 Sundanese
6665 Bashkir
7265 Hausa
7778 Mongolian
8386 Swedish
6669 Byelorussian
7273 Hindi
7779 Moldavian
8387 Swahili
6671 Bulgarian
7282 Croatian
7782 Marathi
8465 Tamil
6672 Bihari
7285 Hungarian
7783 Malay
8469 Telugu
6678 Bengali;Bangla
7289 Armenian
7784 Maltese
8471 Tajik
6679 Tibetan
7365 Interlingua
7789 Burmese
8472 Thai
6682 Breton
7378 Indonesian
7865 Nauru
8473 Tigrinya
6765 Catalan
7383 Icelandic
7869 Nepali
8475 Turkmen
6779 Corsican
7384 Italian
7876 Dutch
8476 Tagalog
6783 Czech
7387 Hebrew
7879 Norwegian
8479 Tonga
6789 Welsh
7465 Japanese
7982 Oriya
8482 Turkish
6865 Danish
7473 Yiddish
8065 Panjabi
8484 Tatar
6869 German
7487 Javanese
8076 Polish
8487 Twi
6890 Bhutani
7565 Georgian
8083 Pashto, Pushto
8575 Ukrainian
6976 Greek
7575 Kazakh
8084 Portuguese
8582 Urdu
6978 English
7576 Greenlandic
8185 Quechua
8590 Uzbek
6979 Esperanto
7577 Cambodian
8277 Rhaeto-Romance
8673 Vietnamese
6983 Spanish
7578 Kannada
8279 Romanian
8679 Volapük
6984 Estonian
7579 Korean
8285 Russian
8779 Wolof
6985 Basque
7583 Kashmiri
8365 Sanskrit
8872 Xhosa
7065 Persian
7585 Kurdish
8368 Sindhi
8979 Yoruba
7073 Finnish
7589 Kirghiz
8372 Serbo-Croatian
9072 Chinese
7074 Fiji
7665 Latin
8373 Singhalese
9085 Zulu
For Your Information
6565 Afar
63
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Correction
No power…
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
• Auto power-off (shut off) occurs after about 5 min. in DVD mode with no
operation, or if there is no broadcast signal in TV or Playback mode. Turn the
power back on.(P. 21, 37)
Power turns itself off...
Monitor
Correction
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 11)
No picture or sound...
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Poor picture with normal • Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP
sound...
Video Adjustment. (P. 47)
Poor sound with normal • Adjust VOLUME control. (P. 22)
picture...
• Adjust SHARPNESS and PICTURE controls in the SET UP Video
Poor TV reception...
Adjustment. (P. 47)
No color or poor color... • Adjust TINT and COLOR controls in the SET UP Video Adjustment. (P. 47)
Ghost (multiple)
• Install a directional antenna.
images...
TV programs cannot be
• Make sure the selected channel is in unit’s memory. (P. 16)
watched...
Channel cannot be
• Only the channel being recorded can be viewed on this unit.
selected...
VCR
Correction
TV program cannot be
recorded...
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 11)
• Make sure cassette record tab is intact. (P. 4)
• Check that clock is set to current time and date.
• Make sure DSS/CABLE box (if used) is left on and tuned to channel to be
recorded.
Timer recording cannot
• Set recording Start/Stop times correctly. (P. 30-31)
be performed…
• Timer recording may not be performed or continued if a power interruption of
more than 1 minute occurs before or during a Timer Recording, even after
power is restored.
No playback picture, or
the playback picture is • Adjust TRACKING control in either direction. (P. 6)
• Try Head Cleaning. (P. 6)
noisy or contains
streaks...
VCR cannot be
• Make sure VCR LOCK is set to off. (P. 39)
controlled...
Remote Control Correction
• Aim Remote directly at the remote sensor on the unit. (P. 9)
Unit cannot be
controlled...
ACTION, PLAY,
SELECT, SET POWER,
etc. buttons cannot be
selected...
64
•
•
•
•
Avoid any object blocking signal path.
Inspect the remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 39)
Exposing unit remote sensor to direct fluorescent or outdoor light may cause
signal interference.
• Press
for TV-VCR mode. (P. 32)
• Press DVD for DVD mode. (P. 32)
• Press FM for FM mode. (P. 32)
• Check remote batteries.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD/Video CD/CD Correction
Play fails to start even
when PLAY is pressed...
Play starts but then
stops
immediately...
Picture is distorted
during rapid advance or
rapid reverse...
No Forward/Reverse
search play...
Play does not start even
when title is selected...
Audio soundtrack and/or
subtitle language is not
the one selected at the
initial settings...
• This unit cannot play discs other than DVDs, Video CDs and CDs.
• The disc may be dirty and require cleaning.
No subtitles...
• Subtitles appear only when available on disc.
• Select “ON” at the “Subtitle language” section (P. 48) to display subtitles.
Alternative audio
soundtrack
(or subtitle) language
cannot be selected...
• Alternative language cannot be selected with discs which do not contain more than
one language.
• For some discs, alternative language cannot be selected with the AUDIO or SUB
TITLE button. Try selecting it from the DVD MAIN MENU if available.
Angle cannot be
changed...
• This function is dependent on software availability. Even if disc has multiple angles,
they may be recorded for specific scenes only (ANGLE Indicator on unit lights up). (P.
49)
Miscellaneous
Correction
Video cassette cannot
be inserted...
Video cassette cannot
be removed...
Eject does not function
or insertion cannot be
done...
Video cassette ejects
when a recording is
started, or the power is
turned off for timer
recording...
The disc cannot be
removed...
• Be sure disc is installed with label side up.
• The picture will be somewhat distorted at times: this is normal.
• Some discs may have sections which prohibit Forward/Reverse search. (P. 21)
• Confirm the “DVD LOCK” setting. (P. 59)
• If the audio soundtrack and/or subtitle language selected at DVD initial settings
does not exist on the disc, it will not be accessible.
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet.
• Turn the POWER off and then on, and try ejecting or inserting the tape again.
• Make sure cassette record tab is intact. (P. 4)
• First, unplug unit. Then, prepare a rigid wire (e.g. an extended paper clip, etc.) and,
applying moderate force, insert it straight into the hole at the base of the tray. The
tray will eject a little. Now, pull the tray all the way out and remove the disc. (P. 10)
In Stop mode, the VCR • To enable Quick Play mechanism, the VCR cylinder will rotate for about 3 minutes.
This reduces response time from Stop to Play mode and from Play to Rewind Search
motor (CYLINDER)
mode.
continues to rotate..
For Your Information
If you cannot resolve the problem, please call the Customer Satisfaction Center for product
assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected]
65
Warning and Instruction Displays
These displays will alert you of a missed operation or provide further instructions.
OSD
PLEASE SET
CLOCK BEFORE
PROGRAMMING
CHECK CASSETTE
RECORD TAB
TO CANCEL TIMER
REC HOLD DOWN
STOP KEY FOR
APPROX 3 SEC
NO CASSETTE
PLEASE INSERT A
CASSETTE
PLEASE PREPARE
FOR TIMER REC
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT
HEAD CLEANING
CASSETTE OR
REFER TO MANUAL
END: PLAY
VCR LOCK
ACTIVATED
PLEASE CHECK
THE DISC, AND
FOR STAINS OR
SCRATCHES ON
DISC
THIS DISC MAY NOT
BE PLAYED IN YOUR
REGION
THIS TYPE OF DISC
CANNOT BE PLAYED.
PLEASE INSERT A
DIFFERENT DISC
CANNOT PLAY THIS
FILE
THIS FILE IS
PROTECTED
IT IS PROHIBITED
TO COPY DVD/
VIDEO CD/CD TO
VHS
66
Caution
If you attempt to set or review a Timer Recording or set the On-Timer and the Clock
is not set... (P.16-17)
If you press REC, and a cassette is inserted with no record tab... (P.4, 18)
If you press STOP during a Timer Recording... (P.31)
If you press PLAY, FF, REW, or REC without a cassette inserted... (P.18)
If the unit is not in Stop mode or a cassette with record tab is not inserted two
minutes before a Timer Recording is about to begin... (P.30-31)
If head cleaning becomes necessary while playing back a tape... (P.6)
If you press a function button other than STOP/EJECT or POWER while the unit is
in VCR Lock mode... (P.39)
If you press PLAY, or the unit reads data from a stained or scratched disc in DVD
mode. Also, if the type of disc is other than DVD, Video CD or CD... (P.7)
Playback of a disc with different region number was attempted. Only discs marked
region “1,” “ALL,” or those that include “1” are playable on this unit. (P.3)
An unusable disc is inserted in the unit. (P.7)
This file format cannot be played.
(Appears during MP3/WMA/JPEG file playback)(P.56)
This file is copyright protected and cannot be played back.
(Playback is prohibited.)(P.56)
If you press REC in DVD mode... (P.18-19)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/Guía para rápida consulta
■ Conexión para Ant./Cable
Nota
Conecte Ant./Cable a la entrada de antena de la TV
(VHF/UHF).
Ant./Cable
VHF/UHF
VHF/UHF
■ Conexión para Sistema Digital de
Satelite (DSS)/Convertidor de cable
Conecte la salida del convertidor de cable la entrada
“VFH/UHF” con el RF cable.
Convertidoe de cable
Ant./Cable
VHF/UHF
Conecte por favor todas las conexiones del cable o
de la antena antes de energizar los aparatos.
• Los botones de funciones son inoperantes
durante la Configuración inicial.
• Para retirar un cassette durante el Ajuste
automático, pulse EJECT dos veces en el control
remoto o STOP dos veces en el VCR. En este
caso, los ajustes se deben realizar manualmente.
(Vea la p.16-17 de Libro de operaciones
avanzadas).
• Dependiendo de las condiciones, puede que
el Ajuste automático del reloj tarde más de
30 minutos. En ese caso, pulse STOP para
detener la configuración y realice los ajustes
manualmente. (Vea la p.16-17 de Libro de
operaciones avanzadas).
Ajuste Manual del Reloj
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente de la
siguiente manera.
1
2
Presione ACTION en el control
remoto para visualizar la pantalla
del menú RELOJ.
Presione ▲▼ para seleccionar el
mes y SET para colocarlo. De la
misma forma, seleccione y ajuste
la fecha, año, hora y DST (Hora de
Verano).
3
Presione dos veces la tecla
ACTION para poner el RELOJ en
marcha y salir.
Realizando Configuración Inicial
Presione
1
2
para la modalidad TV-VCR.
Conecte el cable electrico de la unidad
en el enchufe de pared de la CA.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
Encienda la TV
mediante el control
o directamente en
la unidad. La unidad
inicia la busqueda
de canales y
ajusta el tiempo
automaticamente.
Ajustar de nuevo el reloj
1
2
• Si usa convertidor de cable, enciendala y seleccione el
Servicio Publico de Canales de Television (PBS) en su
horario de uso o tiempo de su zona. Si utiliza receptor
DSS este debe de estar apagado.
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
DVD
BLOQUEO IDIOMA
53
Selecciones
se realizaran
automaticamente,
cuando la
configuracion
termine la pantalla
siguiente aparecera.
• Si “AUTO CLOCK SET IS
INCOMPLETE” aparece
en pantalla, coloque
el tiempo usando el
procedimiento manual
(MANUAL CLOCK SET),
vealo enseguida.
Continúa...
RELOJ
1
CANAL
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
3
FIJAR RELOJ
FIJACION AUTOMATICA
MANUAL
AJUSTE ZONA HORA : 0
ELEGIR :
FIJAR : SET
TERMINAR : ACTION
4
FIJAR RELOJ
2 / 6/2003 JUE 12: 00PM
VERANO : ACT
ELEGIR HORA
ELEGIR:
FIJAR : SET RETROCEDER:
I NIC I AR : ACTION
5
Presione ▲▼◄
► para
seleccionar
“RELOJ,” y
luego Presione
SET.
Presione ▲▼
para seleccionar
“MANUAL” y
luego presione
SET.
Presione ▲▼ y
SET para
seleccionar y
ajustar la hora y
la fecha.
Presione ACTION dos veces para
que el reloj comience a funcionar y
salir de este modo.
For Your Information
3
MENU PRINCIPAL
TV
CANCEL : PRESS STOP KEY
2 / 6 / 2003 THUDST
12 :: ON
00PM
Presione ACTION para visualizar el
menú.
67
Spanish Quick Use Guide/Guía para rápida consulta
Operaciones básicas para la
reproducción (VCR)
1
2
Inserte un cassette.
• El videograbador combinado se enciende
automáticamente.
Presione PLAY.
• La reproducción comienza automáticamente si
el cassette no tiene la lengüeta para prevención
de grabación.
■ Para encontrar una escena en particular
Búsqueda hacia adelante
➞ Presione FF/SLOW+
Búsqueda hacia atrás ➞ Presione
REW/SLOW■ Para ver una imagen fija (congelada) ➞
Presione STILL/PAUSE
■ Para ver en cámara lenta ➞ Presione
FF/SLOW+ o REW/SLOW- en el modo de
imagen fija
■ Para ver imágenes cuadro a cuadro ➞
Presione STILL/PAUSE en el modo de imagen
fija
■ Para parar ➞ Presione STOP
■ Para rebobinar la cinta ➞ Presione
REW/SLOW■ Para hacer avanzar la cinta rápidamente ➞
Presione FF/SLOW+
■ Para expulsar el cassette ➞ Presione EJECT
en el control remoto o STOP/EJECT en el
videograbador combinado
Operaciones básicas para la grabación
1
2
3
Inserte un cassette con la lengüeta
para prevención de grabado.
• El videograbador combinado se enciende
automáticamente.
Presione CH ▲▼ o las teclas numéricas
para seleccionar el canal.
1
2
• Para no editar ó grabar partes de una grabación,
presione STILL/PAUSE para hacer una pausa
durante la grabación.
• No podrá ver otro canal durante la grabación.
F I JAR PROGRAMAC I ON
TEMPOR l ZADOR
ENCENDIDO AUTOMATICO
TEMPOR l ZADOR - DORMIR : 00
1) Presione ▲▼
para seleccionar
“TEMPORIZADOR.”
2) Presione SET
para visualizar.
• Si ya existe un programa en la memoria,
presione ▲▼ y SET para seleccionar un
número de programa sin usar.
3
FECHA
INICIO
PARADA
CA
7 VIE --:-- --:-- -SLP
HOY
-----------------------ELEGIR FECHA DE INICIO
ELEG l R :
F I JAR : SET
TERM l NAR : PROG
Presione ▲▼
para seleccionar y
presione SET o ◄►
para colocar.
• 1-31 = Grabación única
• DIARIO = a la misma
hora de lunes a viernes
• SEMANAL = a la misma
hora una vez a la
semana
Fecha
de hoy
Repita el paso 3 para ajustar:
hora de comienzo, hora de parada, canal (o LINEA
para una fuente exterior), velocidad (SP, LP, SLP)
4
P
1
2
3
4
FE I N I C PARADA
D I 9 : 00p 12 : 00a
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
CANCELAR : ADD/DLT
ELEG I R 1-8 :
ENTRAR : SET
TERM I NAR : PROG
SP = reproducción normal
LP = reproducción larga
SLP = reproducción super larga
Presione REC para comenzar la
grabación.
Presione PROG para visualizar “FIJAR
PROGRAMACION.”
ELEG l R :
F I JAR : SET
TERM l NAR : PROG
Presione SPEED para seleccionar
la velocidad de grabación.
• La velocidad seleccionada debe aparecer en la
pantalla.
4
Grabación con temporizador
5
CA VEL
08 SP
-- --- --- --
Presione PROG para
terminar el programa.
Para introducir
más programas,
presione ▲▼ y SET
para seleccionar el n
úmero de programa
en blanco, y luego
repita los pasos 3.
Presione PROG dos veces para salir de
este modo.
• Si está usando un decodificador de TV cable,
asegúrese que se encuentra en el canal
deseado y que la alimentación queda conectada
para grabar con temporizador.
• El indicador PROG TIMER se enciende en el
videograbador combinado.
■ Para parar ➞ Presione STOP.
■ Si se desea que el videograbador
deje de grabar a una hora
prefijada. (Grabación de un toque)
Presione REC repetidamente para ajustar la
hora de grabación (30 min - 4 horas.)
68
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Operaciones básicas del DVD
1
2
Presione POWER en el control remoto o
el aparato y luego el boton DVD.
Introducir un disco.
1) Presione OPEN/CLOSE.
2) Ponga un disco en la bandeja de disco.
• Sujete el disco sin tocar ninguna de sus
superficies, póngalo con el lado donde esté
impreso el título hacia arriba, alinéelo con las
guías y póngalo en su posición apropiada.
Disco de 3”(8 cm)
Disco de 5” (12 cm)
3
Presione PLAY para Iniciar la
reproducción. La bandeja del disco se
cierra automáticamente.
• Si está usando un DVD interactivo (Interactive
DVD) o un Vídeo CD con contol de reproducción
(playback control) y aparece un menú de títulos
(TITLE MENU) en la pantalla, siga al paso 4.
4
5
6
1) Presione ▲▼◄► o las teclas
numéricas para seleccionar el
artículo deseado.
2) Presione SET para la reproducción.
Si usa las teclas numéricas,
la reproducción comienza
automáticamente.
Presione STOP para parar la
reproducción.
EI idioma de los subtítulos seleccionado al hacer
las fijaciones iniciales se puede cambiar por otro
idioma diferente, si éste se encuentra disponible.
SUBTITULO : 1 ENG ACTIVO
I love you
■ Para ver una imagen fija
Presione PAUSE durante la reproducción. (Para
liberar, presione PLAY)
■ Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione STILL/PAUSE en el modo de imagen
fija. La imagen avanza un cuadro cada vez que
presiona la tecla. (Para volver a la reproducción
normal, presione PLAY.)
■ Para ver en cámara lenta
(DVD/Vídeo CD)
Presione FF/SLOW+ o FF/SLOW- en el modo
de imagen fija. (Para liberar, presione PLAY)
Presione SUBTITLE
durante la
reproducción.
• Cuando no haya subt
ítulos grabados, “-” se
visualizará en lugar del
número de idioma.
Cambio del idioma de la pista de sonido
[DVD solamente]
EI idioma de la pista de sonido seleccionado al
hacer las fijaciones iniciales se puede cambiar
por otro idioma diferente, si éste se encuentra
disponible.
1
Presione AUDIO
durante la
reproducción para
visualizar la pantalla
AUDIO.
SUBTITULO : 3 ESP ACTIVO
Te amo
ELEGIR
:
ACTIVO/INACTIVO :
TERMINAR
: SUB TITLE
2
Presione ▲▼ para
seleccion el idioma
deseado.
For Your Information
ELEGIR
:
ACTIVO/INACTIVO :
TERMINAR
: SUB TITLE
2
■ Para saltar un capítulo o una pista Salto
hacia adelante
l en el modo de reproducción.
Presione SKIP+
Un capítulo (DVD) o una pista (Vídeo CD/CD)
se salta cada ves que se oprime la tecla.
Salto hacia atrás ➞
en el modo de reproducci
Presione SKIP- l
ón.
Presione OPEN/CLOSE para expulsar el
disco.
Cambio del idioma de subtítulos
[DVD solamente]
1
■ Para buscar una escena en particular
Búsqueda hacia adelante
Presione FF/SLOW+ en el modo de
reproducción.
Búsqueda hacia atrás ➞
Presione FF/SLOW- en el modo de reproducción.
(Para liberar, presione PLAY)
69
Visión desde otro ángulo [DVD solamente]
Algunos discos DVD tienen escenas que han sido filmadas
simultáneamente desde un número de ángulos diferentes.
Con estos discos, la misma escena podrá verse desde
cada uno de estos ángulos diferentes utilizando el botón
ANGLE.
1
ANGULO: 1
Presione ANGLE
durante la
reproducción para
visualizar la pantalla
de ángulo.
Utilización de un menú de títulos
[DVD solamente]
Algunos discos con películas, por ejemplo,
vienen con dos o más títulos. Si el disco tiene
un menú de títulos grabados, el botón TITLE
podrá utilizarse para seleccionar el título de la
película.
1
Presione TITLE durante la
reproducción. Ahora se visualiza una
lista de los títulos del disco.
ELEGIR :
2
ANGULO: 2
Presione ▲▼ para
seleccionar el ángulo
deseado.
2
ELEGIR :
Selección de vocal para los discos de Karaoke
[DVD/Video CD]
1
2
Presione AUDIO durante la reproducción
para visualizar la pantalla AUDIO.
SONIDO: 2 ENG VOZ ACTIVO
:
ELEGIR
TERMINAR : AUDIO
1) Presione ▲▼ (o ◄►)
para seleccionar el
ajuste deseado.
2) Presione ►(o ◄)
para ajustar. (DVD
solamente)
Ampliación de la imagen [DVD solamente]
Utilización de un menu de DVD
[DVD solamente]
Algunos discos DVD tienen estructuras
únicas de menús llamadas menús DVD.
Por ejemplo, los DVDs programados con un
contenido complejo proporcionan menús guía,
y los grabados con varios idiomas proporcionan
menús para audio e idiomas de subtítulos.
Aunque los contenidos de los menús DVD
y la operación cambian de disco a disco, a
continuación se explica la operación básica
cuando se utiliza esta característica.
1
Durante la reproducción de un DVD, puede ampliar a
imagen seleccionando la relación de zoom usando el
botón ZOOM mediante control remoto.
Seleccione el tamaño de la imagen.
Presione ZOOM repetidamente para cambiar el
tamaño de la imagen como se indica a continuación:
1) Presione ▲▼◄
► o las teclas
numéricas para
seleccionar el
título deseado.
2) Presione SET o
PLAY.
2
Presione MENU durante la
reproducción. El menú de DVD
introducido en el disco se visualiza
ahora.
1) Presione
▲▼◄► o
las teclas
numéricas para
seleccionar
el articulo
deseado.
2) Presione SET o
PLAY.
■ Use los botones , , y para desplazar
la posición hacia arriba, hacia abajo, hacia la
izquierda o hacia la derecha.
70
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Reproducción programada
[Vídeo CD/CD]
Reproducción arbitraria
[Vídeo CD/CD]
Puede usted programar pistas específicas y el orden de
reproducción.
Las pistas se reproducen de forma arbitraria.
1
1
2
2
Presione ACTION en el modo paro (STOP)
para visualizar MAIN MENU.
MENU PRINCIPAL
DVD
BLOQUEO IDIOMA
53
TV
RELOJ
1
CANAL
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
3
DVD MENU PRINCIPAL
IDIOMAS DEL DISCO
SALIDA DE AUDIO
DETENER RASTREO : CAMPO
4 : 3 PREFERENCIA : L e t t e r b o x
MODO DE REPRODUCCION
ELEGIR
FIJAR
TERMINAR
4
MODO DE REPRODUCCION
REPRODUCCION DE PROGRAMAS
REPRODUCCION ALEATORIA
ELEGIR
FIJAR
TERMINAR
5
:
: SET
: ACTION
:
: SET
: ACTION
REPRODUCCION DE PROGRAMAS
DISCO
PROGRAMA
1 6 11 16
5 8
2 7 12 17
15 6
3 8 13 18
1 13
4 9 14 19
3 2
5 10 15 20
2
BORRAR EL ULTIMO
BORRAR TODO
ELEGIR
:
FIJAR
: SET
TERMINAR : ACTION
INICIAR
1) Presione
▲▼◄► para
seleccionar “DVD.”
2) Presione SET para
visualizar.
1) Presione ▲▼
para seleccionar
“MODO DE
REPRODUCCION.”
2) Presione SET para
visualizar.
Repita los pasos 1-3 de la
“Reproduccion programa”.
MODO DE REPRODUCCION
REPRODUCCION DE PROGRAMAS
REPRODUCCION ALEATORIA
ELEGIR
FIJAR
TERMINAR
:
: SET
: ACTION
1) Presione
▲▼ para
seleccionar
“REPRODUCCION
ALEATORIA.”
2) Presione SET.
• Comienza la
reproducción
arbitraria.
• Para cancelar,
presione STOP
durante la
reproducción y
luego presione
CLEAR.
1) Presione ▲▼
para seleccionar
“REPRODUCCION
DE PROGRAMAS.”
2) Presione SET para
visualizar.
1) Presione ▲▼◄►
para seleccionar el
número de la pista
deseada. (Se
visualizan los
números de la pista
del disco).
2) Presione SET para
seleccionar.
• Repita el paso 5 para
seleccionar otra pista.
• La pista seleccionada se
añade a la parte derecha.
REPRODUCCION DE PROGRAMAS
DISCO
PROGRAMA
1 6 11 16
5 8
2 7 12 17
15 6
3 8 13 18
1 13
4 9 14 19
3 2
5 10 15 20
2
BORRAR EL ULTIMO
BORRAR TODO
ELEGIR
:
FIJAR
: SET
TERMINAR : ACTION
INICIAR
1) Presione ▲▼◄►
para seleccionar
“INICIAR.”
2) Presione SET.
• La reproducción
comienza en la secuencia
programada.
• Para cancelar, presione
STOP durante la
reproducción y luego
presione CLEAR.
For Your Information
6
71
Spanish Quick Use Guide/Guía para rápida consulta
Funcionamiento del DVD utilizando
visualizaciones en pantalla
Cuando se presiona DISPLAY, la visualización
en pantalla muestra la información del disco
(título / capítulo / número de lista, tiempo
transcurrido de reproducción, audio / idioma
del subtítulo, y ángulo) e información (repetir
la reproducción, modo reproducción, Karaoke
vocal encendido / apagado, etc.).
1
Presione DISPLAY en el modo
reproducción o parada para visualizar
en pantalla.
• Cada vez que se presione DISPLAY, la
visualización en pantalla cambia como se
muestra a continuación.
Información seleccionada del disco
Información seleccionada de la unidad
Pantalla normal
1) Presione ▲▼ (o ◄►) para
seleccionar el articulo deseado.
2) Presione SET para colocar.
2
3
<Ejemplo de DVD>
T I TULO : 12
CAPITULO: 11
DVD
0 : 12 : 34
T I TULO : 12
CAPITULO: 24
DVD
0 : 12 : 34
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
1) Presione
▲▼ para
seleccionar
el ajuste
deseado.
2) Presione
SET para
colocar.
<Ejemplo de Vídeo CD>
PISTA
PBC
: 12
: INACTIVO
PISTA
PBC
FIJAR
VIDEO CD
0 : 12 : 34
: 17
: INACTIVO
VIDEO CD
0 : 12 : 34
: SET SIGUIENTE: DISPLAY
FIJAR
: SET SIGUIENTE: DISPLAY
Para volver
a la pantalla
normal,
presione
repetidamente
CLEAR o
DISPLAY.
Fijaciones iniciales
1
2
3
Presione ACTION en el modo de paro
(STOP) para visualizar MAIN MENU.
1) Presione ▲▼◄► para seleccionar
“DVD.”
2) Presione SET para visualizar.
1) Presione st para seleccionar el artículo
deseado.
2) Presione SET.
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser
ajustados, Si el idioma ajustado no es ofrecido en el
disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente de la
terminal de salida audio digital.
DETENER RASTREO
Para seleccionar “CAMPO” o “CUADRO” para
prevenir inestabilidad o para permitir ver textos
pequeños o patrones finos claramente en el modo de
imagen fija.
4 : 3 PREFERENCIA
Para seleccionar si el material del vídeo para pantalla
ancha será vuelto a reproducir en el estilo Pan&Scan
o en el estilo Letterbox en la pantalla.
4
5
1) Presione st para seleccionar el artículo
deseado.
2) Presione SET.
Volver a visualizar el menú de
DVD para continuar el ajuste.
Presione ACTION y pase al paso 3 para ajustar
otro articulo o, para salir, presione ACTION
tres veces.
Selección de IDIOMAS DEL DISCO
[DVD solamente]
Seleccione “AUDIO”
Inglés/Español/Francés/Japones: (Fijación de fábrica : inglés)
Original : Se seleccionará el idioma original de cada
disco.
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “SUBTITULO”
AUTO : Se seleccionará el mismo que fue seleccionado en
la preparación de “AUDIO”. (Fijación de fábrica)
• Si el idioma seleccionado en la preparación de
“AUDIO” se utiliza durante la reproducción, los
subtítulos no aparecerán.
• Si se utiliza otro idioma durante la
reproducción, los subtítulos aparecerán en
el idioma seleccionado en la preparación de
“AUDIO”
Inglés/Español/Francés/Japones
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “MENU”
Inglés/Español/Francés/Japones : (Fijación de fábrica : inglés)
OTRO **** : Se puede seleccionar el otro idioma.
72
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Selección de 4 : 3 PREFERENCIA
4:3 Pan&Scan : Datos de la pantalla ancha
de vídeo son reproducidos
en el estilo Pan & Scan (la
parte derecha e izquierda de
la pantalla son recortadas).
(Fijación de fábrica)
• Datos de vídeo no
formateados en Pan & Scan
serán reproducidos en el estilo
letterbox.
4:3 Letterbox :
Datos de la pantalla ancha de
vídeo son reproducidos en el
estilo Letterbox (la parte de
arriba y abajo de la pantalla
tienen un margen negro).
Selección de DETENER RASTREO
AUTO :
Durante el modo de imagen fija se
seleccionarán automáticamente
“Campo fijo” o “Cuadro fijo” (Fijacion
de fabrica)
CAMPO :
Seleccione este ajuste cuando ocurra
“distorsión” en las imagenes, incluso
cuando se haya seleccionado “AUTO”.
CUADRO : “Cuadro fijo” esta siempre
seleccionado. Se utiliza cuando no
se puedan ver claramente textos
pequeño o patrones finos incluso
cuando esté seleccionado “AUTO”.
Funcionamiento de la ejecución de MP3/WMA/JPEG
Puede utilizar esta unidad para reproducir audio
de formato MP3/WMA/JPEG, grabado para uso
personal con una computadora, etc., en un
CD-ROM o CD-RW.
La ejecución puede no tener lugar en algunos
casos, debido a las condiciones de la grabación.
1
2
3
Presione POWER en el control remoto o
unidad.
Presione OPEN/CLOSE y a continuacion
coloque un disco MP3/WMA/JPEG en la
bandeja de discos.
Presione OPEN/CLOSE para cerrarla.
Se visualizará el MENU MP3/WMA/JPEG
y la ejecución se iniciará
automáticamente.
(Se visualizará el directorio del CD.)
Contador
Estado de
la función
REPROD
00 : 00 : 00
..
CAR1
CAR2
END_WALTZ
PICTURES
:Archivo MP3
:Archivo WMA
:Carpeta
:Carpeta principal
:Archivo JPEG
■Seleccione MODO DE REPRODUCCION
(Durante el modo STOP)
para mover el cursor a MODO DE
Presione
para
REPRODUCCION, y Presione
seleccionar el
MODO DE REPRODUCCIÓN deseado.
[MODO DE REPRODUCCIÓN]
NORMAL: Todos los archivos se reproducen sólo
una vez
REPETICION DE UNA MUSIC:
El archivo seleccionado se reproduce
repetidamente.
REPETICION DE UN ARCHIVO:
Los archivos que se encuentran en la carpeta
seleccionada se reproducen repetidamente.
REPETICION DEL DISCO:
Todos los archivos se reproducen repetidamente.
4
Presione ACTION para regresar al DVD
MAIN PRINCIPAL.
For Your Information
Carpeta
principal
Área de las
Área de
carpetas
archivos
(La carpeta
(El
visualizada
MODE DE REPRODUCCION:
archivo/ la
NORMAL
actualmente
carpeta se
se volverá
visualiza
verde)
con un
MODO DE REPRODUCCIÓN cursor.)
ROOT
My favorite
TECHNO
POPS
JAZZ
■Ejecución MP3/WMA/JPEG (Durante el modo STOP)
Presione
para seleccionar un archivo
MP3/WMA ( / ) o un archivo JPEG ( ), y
presione SET o PLAY.
• MP3/WMA
Búsqueda hacia adelante/hacia atrás
➞Presione FF/SLOW+ o REW/SLOW- durante la
ejecución.
Salto de Pista hacia adelante/hacia atrás
| o SKIP-|
➞Presione SKIP+
durante la
ejecución.
• JPEG
Búsqueda siguiente/anterior
| o SKIP-| .
➞Presione SKIP+
Inicie la muestra-diapositiva
➞Presione FF/SLOW+ o REW/SLOW-.
Ampliando una imagen ➞Presione ZOOM.
Rotando una imagen ➞Presione ANGLE.
Presione STOP para detener la operacion descrita
arriba.
73
Limited Warranty
PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF
MATSUSHITA ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial
Park, Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original
purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, or
(b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the
warrantor.
Product
Camcorder
DVD/VCR Deck,
A/V Mixer
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
TV/HDR
Combination
Rechargeable
Batteries
(in exchange for
defective item)
Tape
(in exchange for
defective item)
Memory Cards
(in exchange for
defective item)
Parts
Labor
One (1) Year (except CCD Ninety (90) Days
Image Sensor)
CCD Image Sensor - 6 (Six) Ninety (90) Days
Months
One (1) Year
Ninety (90) Days
One (1) Year (except CRT) Ninety (90) Days
CRT - Two (2) Years
Ninety (90) Days
Service
Contact Number
Carry-In or Mail-In
1-800-211-PANA(7262)
Carry-In or Mail-In
1-800-211-PANA(7262)
Carry-In: 21″ CRT and Smaller
In-Home or Carry-In: 22″ CRT and 1-800-211-PANA(7262)
Larger
One (1) Year (except CRT) Ninety (90) Days
CRT - Two (2) Years
Ninety (90) Days
In-Home or Carry-In
1-888-843-9788
Ten (10) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Five (5) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,
there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home
service, as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to
products purchased and serviced in the United States or Puer to Rico. This warranty is extended only to
the original purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of
the original purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact
number listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the
authorized servicer and does not include removal or re-installation of an installed product. It is possible
that certain in-home repairs will not be completed in-home, but will require that the product, or parts of
the product, be removed for shop diagnosis and/or repair and then returned.
74
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on
the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures
on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen
data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which
occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures
which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power
line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or
other business), rental use of the product, service by anyone other than a Factory Servicenter or other
Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone
remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or
images, data or other memory or recorded content. The items listed are not exclusive, but are for
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state. If a problem with this product develops during or after the warranty period, you may contact
your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’
s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE
APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR
RESPONSIBILITY.
Customer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer
Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm,
EST. or send e-mail : [email protected]
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of August 2002
For Your Information
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
75
Index
TV / VCR
A Accessories ................................................. 4
B
C
D
E
F
76
AC Power Plug........................................... 11
ACTION button ...................................... 8, 16
ADD/DLT/CLEAR button........................ 8, 17
Audio Adjustment ...................................... 47
Audio Auto Gain Control (AGC) ................. 46
AUDIO button .................................. 8, 23, 44
Audio Connections .................................... 12
Audio Features .....................................44-45
Audio Menu ............................................... 46
Audio Mode for FM Radio.......................... 29
Audio Mode for Playback ........................... 44
Audio Mode for Recording ......................... 44
Audio Mode for TV Viewing........................ 23
Audio Mute ................................................ 22
Audio/Video Input connector (LINE) .... 10, 19
Audio Output Connector (L/R) ..............11-12
Auto Operation Functions .......................... 37
Batteries ...................................................... 4
Before Requesting Service...................64-65
Before Using................................................ 4
Blocking Message ..................................... 43
Blue Screen Display .................................. 27
Broadcast Types ........................................ 23
Cable Box Brand Code Number ................ 33
Cable Box Universal Remote
Control Feature.......................................... 32
Cassette Compartment ............................. 10
Caption On Mute ...................................... 25
Channel ..........................................16-17, 27
CHANNEL UP/DOWN button ................ 8, 22
Clock.....................................................16-17
Closed Caption .....................................24-25
CM SKIP/ZERO SEARCH button .....8, 36-37
Code Numbers, DSS/Cable Box Brand ..... 33
Commercial Skip ....................................... 37
Connections............................................... 11
Connections, Audio.................................... 12
Connections, DSS/Cable Box.................... 11
Connections, Antenna/Cable ..................... 11
Copy Your Tapes (Dubbing) ....................... 19
COUNTER RESET button..................... 8, 36
Customer Services Directory ................... 75
DISPLAY/ENTER button.................. 8, 27, 32
DSS Brand Code Number ......................... 33
DSS CABLE button ............................... 8, 32
DSS/Cable Box Connections..................... 11
DST (Daylight Saving Time) ........................ 6
EJECT button ...........................................8-9
Eject tape................................................... 18
Fast Forward.............................................. 18
FF/SLOW+ button.................................. 8, 18
FM button .........................................8, 28-29
FM Radio ..............................................28-29
Forward Search ......................................... 18
Frame by Frame Advance ......................... 18
Front Panel Indicators.................................. 9
Function Display ........................................ 27
H Head Cleaning............................................. 6
I Important Safeguards and Precautions ....... 2
L
M
N
O
P
Q
R
S
Information (Unit, Cassette, Disc).............6-7
Initial Setup................................................ 14
Index Search ............................................. 34
Indicators on the Front Panel....................... 9
Input Mode................................................. 19
Language................................................... 16
LIGHT button ............................................8-9
Limited Warranty...................................74-75
Location of Controls................................8-11
MTS Broadcast/TV Stereo System............ 23
MUTE button ......................................... 8, 22
NUMBER keys....................................... 8, 22
100 Key...................................................... 22
One Touch Recording (OTR) ..................... 18
On-Screen Display (OSD) ......................... 27
ON-TIMER Indicator .............................. 9, 26
ON-TIMER with Alarm ............................... 26
Phones ...................................................... 22
Playback .................................................... 18
PLAY button........................................... 8, 18
POWER button ...................................... 8, 14
PROG button ................................... 8, 26, 30
PROG TIMER Indicator ......................... 9, 30
Quality Picture ............................................. 6
Rapid Tune................................................. 22
R-TUNE button ...................................... 8, 22
REC button ............................................ 8, 18
REC Indicator ........................................ 9, 18
Rec(ord)..................................................... 18
Record/Playback Speed Settings ................ 4
Remote Control Buttons .............................. 8
Remote Sensor............................................ 9
Remote Warning Feature .......................... 39
Repeat Play ............................................... 35
Reset Language, Channels, Clock .......16-17
Reset unit .................................................. 15
Reverse Search ......................................... 18
REW/SLOW- button............................... 8, 18
Rewind....................................................... 18
Safety Precautions ...................................... 3
SEARCH button................................8, 34-35
Secret Code............................................... 40
Selecting Input Mode................................. 19
SELECT/SET button.............................. 8, 16
Sleep Timer ............................................... 26
Slow Motion ............................................... 18
Spanish Quick Use Guide .................. 67-73
Special VCR Features ..........................38-39
Specifications .............................................. 6
SPEED button ....................................... 8, 18
Still Picture................................................. 18
STILL/PAUSE button ............................. 8, 18
STOP button .......................................... 8, 18
SURROUND button ............................... 8, 45
Surround Sound ........................................ 45
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : con[email protected]
TV / VCR
T Table of Contents......................................... 5
Tape Erasure Prevention ............................. 4
Tape Operation .....................................34-37
Timer Program Review, Replace, Clear ..... 31
Timer Recording ........................................ 30
Timer Recording Cancellation ................... 31
Time Zone Adjust....................................... 17
TRACKING/V-LOCK buttons ................... 6, 8
TV Operation ............................................. 22
TV Timer Features ..................................... 26
TV - VCR button..................................... 8, 32
TV/VCR Status & Clock Display ................ 27
U Unit, Front/Rear View............................10-11
Universal Remote Control ......................... 32
US MOVIES Ratings.................................. 41
US TV PROGRAMS Ratings ..................... 42
DVD
A ANGLE button ................................. 8, 49, 58
B
C
D
J
K
Video Adjustment....................................... 47
Video Menu................................................ 46
V-Chip Control Feature .......................40 - 43
VHF/UHF Antenna Input Terminal ............. 11
VOLUME UP/DOWN button .................. 8, 22
W Warning and Instruction Displays .............. 66
Weak Signal Display Feature..................... 38
Z Zero Search............................................... 36
L Language Code List .................................. 63
M MENU button ......................................... 8, 50
O
P
R
S
T
U
V
W
Z
MP3 Playback............................................. 57
Multiple angle viewing (DVD)..................... 49
OPEN/CLOSE button ............................ 8, 20
Optical digital audio output connector .....11-13
Picture Zoom (DVD) .................................. 49
Play............................................................ 20
Playback control (Video CDs).................... 21
PLAY button........................................... 8, 20
Program Play (Video CD/CD).................... 51
Program Repeat Play (Video CD/CD) ....... 51
Random Play (Video CD/CD) .................... 52
Region number ............................................ 3
Repeat Play ............................................... 55
RESUME function ..................................... 21
RETURN button .................................... 8, 20
REW/FF/SLOW +/- button .....8, 20-21, 57-58
Settings for DVD Operation ..................60-62
|/SKIP- |
..........8, 20-21, 56-58
SKIP+
Slow Motion (DVD/Video CD).................... 21
STILL MODE ............................................. 62
Still (Pause) Picture ................................... 21
STILL/PAUSE button ............................. 8, 21
Subtitle language (DVD) ............................ 48
SURROUND button............................... 8, 45
TV MODE .................................................. 62
Title menu (DVD) ....................................... 50
Unit information screen (Unit).................... 55
V.S.S. (Virtual Surround Sound) ................ 45
WMA Playback ........................................... 57
ZOOM button......................................... 8, 49
For Your Information
F
ANGLE Indicator.................................... 9, 49
Auto-Power Off function............................. 21
AUDIO button .................................. 8, 48, 49
AUDIO OUTPUT........................................ 61
Audio soundtrack language (DVD) ............ 48
Basic DVD Operation................................. 20
CLEAR button...................................8, 51-53
Definition of terms ....................................... 7
Disc Audio attribute 1 type, sampling
frequency, bit No........................................ 48
Disc format .................................................. 7
Disc handling ............................................... 7
Disc information screen ............................. 54
DISC LANGUAGES (DVD) ........................ 60
Disc Operation......................................48-52
Disc Tray .......................................... 7, 10, 20
DISPLAY button..................................... 8, 53
DVD button ............................................ 8, 20
DVD Lock Feature (DVD)........................... 59
DVD Lock Ratings (DVD)........................... 59
DVD menu (DVD) ...................................... 50
DVD Operation using On-Screen Displays ..... 53
DVD Volume Adjust ................................... 45
Forward/Reverse Chapter/Track skip .......... 21
Forward/Reverse rapid scene search ........ 21
Frame by Frame picture
(DVD/Video CD) ........................................ 21
JPEG Playback ......................................57-58
Karaoke (DVD/Video CD) .......................... 49
V VCR Lock .................................................. 39
77
NOTES
78
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
NOTES
79
LSQT0668B
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
P
Printed in Indonesia
LSQT0668B
S0203-1033
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement