Samsung | AWT18F1HBA | User manual | Samsung AWT18F1HBA User Manual

OWNER’S
INSTRUCTIONS
AWT18F1HBA/BB/BC
AWT19F1HEA/EB/EC
AWT24F1HBA/BB/BC
AWT24F1HEA/EB/EC
AWT18A1HBA/BB/BC
AWT19A1HEA/EB/EC
AWT24A1HBA/BB/BC
AWT24A1HEA/EB/EC
Window-type Room Air Conditioner
( Cool )
E PE DB98-13920A(2)
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
1 The unit must be plugged into an independent circuit.
The air conditioner must be installed in accordance with national wiring regulations and
safety regulations wherever applicable.
2 Some installation locations may require installation of a short circuit breaker or grounding.
3 If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
4 MAKE sure that the unit is correctly ventilated at all times :
do NOT place clothing or other materials over it.
5 NEVER spill any kind of liquid into the unit. Should this happen, unplug the unit and
contact an authorized service center.
6 Do NOT insert anything between the air outlet blades because the inner fan may be
damaged and could cause injury. Keep children away from the unit.
7 Do NOT place any obstacles in front of the unit.
8 Users of this product are cautioned not to attempt repairs.
Instead, they are requested to directly contact a designated service center or the
outlet at which the product was purchased.
9 Do not use an extension cord with this product.
10 The appliance is not intended for use by young children without supervision ;
young children should be supervised to ensure that they do not play with the appliance.
11 Never store or ship the air conditioner upside down or sideways to avoid damage to
the compressor.
12 Max current is measured according to IEC standard for safety
and current is measured according to ISO standard for energy efficiency.
CC
AA
UU
TT
IIOO
NN
IIOO
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
E-2
Contents
◆ PREPARING YOUR AIR CONDITIONER
■
■
■
Safety Precautions .........................................................................................
Air Conditioning Unit - Main Parts and Control Panel ....................................
Getting Started ...............................................................................................
2
4
5
◆ OPERATING YOUR AIR CONDITIONER
■
■
■
■
■
Cooling Your Room ........................................................................................
Airing Your Room ...........................................................................................
Switching the Air Conditioner Off ....................................................................
Adjusting the Air Flow Direction Horizontally ..................................................
Adjusting the Air Flow Direction Vertically ......................................................
6
7
7
8
8
◆ RECOMMENDATIONS FOR USE
■
■
■
■
■
Operating Recommendation ........................................................................... 9
Temperature and Humidity Ranges ................................................................ 9
Cleaning Your Air Conditioner ........................................................................ 10
Solving Common Problems ............................................................................ 12
Technical Specifications ................................................................................. 12
◆ METHOD OF INSTALLATION ................................................................................. 13
E-3
Air Conditioning Unit - Main Parts and Control Panel
❄ The design and shape are subject to change,
depending on the model.
Inner air flow blades
(right/left orientation)
Air inlet(Inside)
Outer air flow blades
(up/down orientation)
Air inlet (Outside)
Air filter(Inside)
Ventilation lever
Power Cable
BLUE BROWN YELLOW/GREEN
Main Power
Earth
❈ Power cable connection
should be committed to
an installation engineer.
Cooling lamp
Temperature
control dial
Operating mode
selection dial
Air flow blade swing switch
E-4
Getting Started
You have just purchased a window-type room air conditioner and it has been installed
by your installation specialist.
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s features.
The booklet is organized as follows.
◆ The illustration on page 4 shows the air conditioning unit;
it indicates the location and purpose of the main parts and controls on the unit.
◆ In the manual, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH
☛
➢
IMPORTANT
NOTE
E-5
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the fan speed.
1
Select the operating mode and fan speed.
To cool your room
with a...
Set the operating mode
selection dial to...
High fan speed
Hi Cool
Between High and Low
Med Cool
Low fan speed
Low Cool
Result:
◆ The air conditioner starts up in Cool mode.
◆ The fan starts up at the speed selected.
➢
2
27˚C ~ 23˚C
You can change modes at any time.
To adjust the temperature, turn the temperature control dial
to the desired position.
Possible temperatures: Between 18°C and 29°C inclusive.
27˚C
~ 29˚C
23˚C
~ 18˚C
Result:
3
E-6
The air conditioner starts cooling if the room temperature is higher
than the selected temperature.
To control the direction of the air flow, refer to page 8.
Airing Your Room
If the atmosphere in your room is stale, you can air it using
the Fan feature and if necessary, evacuate the stale air outside.
1
If you wish to evacuate stale air outside, push the ventilation lever on the front
of the unit to the right and the open position (
).
Result:
The air inside the room circulates and stale air is evacuated outside.
Otherwise, push the ventilation lever to the left and the closed position (
Result:
2
The air simply circulates inside the room.
Set the operating mode selection dial to the Hi Fan, Med Fan or
Low Fan position.
➢
Result:
3
).
Hi Fan : The fan turns high speed.
Med Fan : The fan turns med speed.
Low Fan : The fan turns low speed.
The air conditioner starts up in Fan mode.
To control the direction of the air flow, refer to page 8.
Switching the Air Conditioner Off
You can switch the air conditioner off whenever you want.
1
To switch the unit off, simply set the operating mode selection dial
to the
position.
Result:
The air conditioner stops operating.
E-7
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the
unit, thus increasing the efficiency of the air conditioner.
1
Set the air flow blade swing switch to the
Result:
2
position.
The inner blades swing automatically left and right.
To stop the blades moving left and right, set the air flow blade swing switch
to the
position.
➢
To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply set the switch to the
position
when the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Adjust the air flow blades to the desired position, by pushing them
upwards or downwards.
➢
E-8
If you orient the air flow blades downwards and the unit operates
in Cool mode for long periods of time, dew may:
◆ Form on the surface of the blades
◆ Drip from the blades
Operating Recommendation
Here is a recommendations that you should follow when using your air
conditioner.
Topic
Recommendation
Power failure
If a power failure occurs when the air conditioner is operating,
the unit is switched off. When the power returns,
the air conditioner starts up again automatically.
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges,
within which the air conditioner can be used.
Mode
Indoor
Temperature
Outdoor
Temperature
Indoor Humidity
Cooling
21°C to 32°C approx.
21°C to 54°C approx.
80% or less
If the air conditioner is used at...
Then...
Higher temperature
The automatic protection feature may be triggered
and the air conditioner stopped.
Lower temperature
A water leakage or some other malfunction may happen
if the heat exchanger freezes.
Higher humidity levels
Water may condense on and drip from the surface of the unit
if it is used for long periods.
E-9
Cleaning Your Air Conditioner (✴✴✴✴F1✴✴✴ models)
Be sure to clean the air filter periodically two weeks to maintain
the air conditioner in the best condition for a long period of time.
☛
1
When cleaning the air conditioner, turn it off and pull out
the power plug.
Hold the air filter handle, slightly pull it to the left side and open the front grille.
➢
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.
CAUTION
Removal and Reassembly of the Front Grille
1 Grasp the lower part of the front
grille and the air filter handle, then
open the grille. (The open angle
of front grille has not to be
exceeded 90 degree)
2 Push the front grille on the left and
remove it from the front panel.
Safety clip
3 Reassembling of front grille
should be done in reverse
order of disassembly.
Front grille
Grille groove
Body guide
2
Pull the air filter to the right side.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
➢
E-10
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for three to four hours
to dry the inside of the air conditioner
thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
Cleaning Your Air Conditioner (✴✴✴✴A1✴✴✴ models)
To get the best possible use out of your air conditioner,
you must clean it regularly by two weeks to remove the dust on the air filter.
☛
1
Open the front grille by pulling on the tabs of the unit.
➢
2
Before cleaning your air conditioner, ensure that it is
switched off and unplugged from the wall socket.
The removal of the front grille makes it easier to clean the air
conditioner. After opening the front grille, lift it up as much as
possible, then pull down to release it.
Grasp the handle on the air filter and lift it slightly and then out to the front.
Front grille
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, slide the air filter back into position.
5
Clean the outer surfaces with a damp cloth and mild detergent
(do NOT use benzene, solvents or other chemicals).
Wipe them dry with a clean, soft cloth.
➢
Front grille
Grille groove
Body guide
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for a few hours
to dry the inside of the air conditioner
thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
E-11
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks.
They may save you the time and expense of an unnecessary call.
PROBLEM
EXPLANATION / SOLUTION
The air conditioner does not
operate at all
◆ Check that the circuit breaker used for the air conditioner
has not been triggered.
◆ Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
◆ Check that the correct operating mode has been selected
(cooling or airing).
◆ Check that the correct operating mode has been selected.
The air conditioner does not
cool
◆ The room temperature may be too low.
◆ Dust may be blocking the air filter;
refer to page 10 and 11 for cleaning instructions.
◆ Check that there is no obstacle blocking the air flow into or out of the unit.
The air flow direction does not
change when you set the air flow
blade swing switch to the
position
◆ Check that the air conditioner has been switched on;
Odours are permeated in the
room during air conditioning
◆ Air the room.
if necessary, turn the operating mode selection dial.
Technical Specifications
Design and specifications are subject to change without notice.
Model
AWT18F1(A1)HBA/BB/BC
AWT24F1(A1)HBA/BB/BC
AWT19F1(A1)HEA/EB/EC
AWT24F1(A1)HEA/EB/EC
E-12
Power Supply
220V~, 60Hz
220V-240V~, 50Hz
Method of Installation
Before installation, be sure to check the installation area
for the air conditioner, and installation method of the drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
75mm
min.
500mm
500mm
300mm
240mm
500mm
Fence, wall
or other
obstacle
Approx.3˚
750mm
➢
150mm min.
◆ If the wall is greater than 150mm thick, cut the wall back on a 45˚ angle if possible.
Outdoor side 45˚
45˚
Indoor side
100mm or more
E-13
Method of Installation
Installation of the Drain Tube
Rear
Fix the drain tube as shown in the figure.
Rubber cap
Gasket
Drain Tube
Screws(2EA)
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
◆ In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1
Open the front grille.
CAUTION
Removal and Reassembly of the Front Grille
1 Grasp the lower part of the front grille and the air filter handle, then
open the grille.
(The open angle of front grille has not to be exceeded 90 degree)
2 Push the front grille on the left and remove it from the front panel.
3 Reassembling of front grille should be done in reverse order of
disassembly.
2
Remove the front panel.
2-1 Press both sides of the cabinet in the direction of the arrow
as shown in the figure.
2-2 Pull the lower part of the front panel slightly forward.
(below three inches)
2-3 Lift the front panel upward.
☛
Front panel
3
E-14
Applying excessive force to remove the front panel
may cause damage to the tab ; be sure not to use
excessive force.
Remove two screws on the lower, right and left sides of the unit.
Method of Installation
4
Remove the chassis from the cabinet.
5
Remove the rubber cap inserted into the basepan.
6
Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
7 Install the cabinet at the specified area after installing the drain pan,
and then re-assemble it in the original condition.
❇ When assembling the front panel be sure to fix with a supplied screw.
Drain Pan
Rear
Rubber cap
Drain Hose
Screw
Bottom-Side View with
Drain Pan and Hose in Place
(TH 2S 4X10)
◆ In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1
Follow steps 5 and 6 only.
Screw
E-15
THIS AIR CONDITIONER IS MANUFACTURED BY:
Printed in Korea
Download PDF