aftermarket radio - CRUX Interfacing Solutions
Rev. 012115
RADIO REPLACEMENT W/SWC RETENTION FOR FORD, LINCOLN, VEHICLES 2011-UP
SWRFD-60B
FORD
2011 - 2015 Edge
2013 - 2015 Explorer
2013 - 2015 F-Series
2012 - 2015 Focus
2013 - 2015 Fusion
2013 - 2015 Taurus
LINCOLN
2011 - 2012 MKX
*Important Note:
Does not retain SYNC
We recommend reading this installation guide first before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We offer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
OVERVIEW OF INSTALLATION
CONNECT THE WIRES,
COLOR FOR COLOR.
MATCH LOOSE WIRES TO AFTERMARKET RADIO
PARTS INCLUDED:
auxiliary Input (3.5mm Input)
(1) FD-60 Interface Module
(1) FD-60 24-Pin Harness
(1) Instruction Sheet
front left speakers
front right speakers
rear left speakers
rear right speakers
constant
accessory
ground
power antenna
illumination
crank 12v output
vss
AFTERMARKET
RADIO
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
PRELIMINARY:
Please read the entire mannual before installing this interface.
Before installing this interface please review the options before
removing the factory radio. Some options may need to be adjusted
prior to removing the factory radio.
BLACK
OPTION B
OPTION A
24-PIN
(male plug)
TO FACTORY
HARNESS
ON
WIRING COLOR CODES
Black Red Yellow Orange Blue/White
White White/Black Gray Gray/Black
Green Green/Black Purple Purple/Black
Red/Black
Red/White
Brown
Blue/Yellow
= Ground
= Accessory (2A Max)
= Constant
= Illumination (100mA Max)
= Antenna Turn-On
= Left Front (+)
= Left Front (-)
= Right Front (+)
= Right Front (-)
= Left Rear (+)
= Left Rear (-)
= Right Rear (+)
= Right Rear (-)
= VSS (Vehicle Speed Sense)
= Reverse
= Crank Output (Constant 12v)
= SWC for Kenwood
INSTALLATION TIPS
1. Test the radio for power, turn the key to the “ON” position and confirm
that the new radio is getting power. If no power, please revise your
wiring connections with multi-meter, avialable at your local car audio
dealer.
SWC 4-PIN CONNECTOR
The module allows for both type of SWC connections:
Option A is used for the Alpine, Clarion, JVC, and Kenwood units.
(Blue/Yellow wire attached)
Option B is used for the Pioneer, and Sony units. (See Overview)
Select the proper harness type for your aftermarket radio and
connect the 4-pin molex to its proper connection.
12-PIN
4-PIN
1
2
3
12-PIN 4-PIN
SETTING THE RADIO TYPE
This step is only needed if the vehicle has steering wheel controls
and you are installing one of the listed radios. With the ignition key
in the off position turn set the dip switchesall steering wheel control
functions.
DIP:
RADIO TYPE:
Pioneer/ SONY/ Jensen
Alpine Clarion Kenwood JVC Blaupunkt Zenec & Digitaldynamic
1
OFF
OFF
ON
ON
ON
ON
OFF
2
3
ON
ON
OFF OFF
ON OFF
ON
ON
OFF
ON
OFF OFF
OFF
ON
USING A RELAY
The module has been rated for upto 2A max of output.
For applications demanding a continuous output of 3A or more,
we reccomend using a standard BOSCH (SPDT) relay.
See your local car audio specialist.
Below is a diagram on how to install the BOSCH relay.
FUSE
ON
1
CAR 12V CONSTANT
87
2
3
CHASIS
GROUND
86
87a
85
TO ACC 12V
30
NEW ACC 12C (HIGH CURRENT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising