VCC-FC20V49CL

VCC-FC20V49CL Rev.900-723-33-00

English

Camera link I/F

29mm cubic VGA

High-Speed Color CMOS Camera

VCC-FC20V49CL

Product Specification

& Operational Manual

CIS Corporation

©2013 CIS Corporation. All rights reserved.

VCC-FC20V49CL Rev.900-723-33-00

Table of Contents

PAGE

1.

Scope of Application .................................................................................................................................................. 3

2.

Handling Precautions ................................................................................................................................................. 3

3.

Notes on Partial Scan Mode Operation ........................................................................................................................ 5

4.

Product Outline ......................................................................................................................................................... 5

5.

Specification ............................................................................................................................................................. 6

5.1.

General Specification ..................................................................................................................................... 6

5.2.

Camera Output Signal Specification ................................................................................................................ 8

5.3.

CMOS Spectral Response (Representative value) ............................................................................................. 9

5.4.

Video Output Format ..................................................................................................................................... 9

5.5.

Camera Link Port Data Bit Assignment (Base Configuration) ........................................................................... 10

6.

Function Settings .................................................................................................................................................... 11

7.

External Connector Pin Assignment ........................................................................................................................... 13

7.1.

6pins Circular Connector HR10-7R-6PA (HIROSE) equivalent ........................................................................ 13

7.2.

26pins Mini Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M) ..................................................... 13

8.

Timing Chart ........................................................................................................................................................... 14

8.1.

Horizontal Synchronous Signal Timing ........................................................................................................... 14

8.2.

Vertical Synchronous Signal Timing ............................................................................................................... 14

8.2.1

Full Frame Scan Mode .................................................................................................................................. 14

8.2.2

Fixed Trigger Shutter Mode .......................................................................................................................... 15

8.2.3

Pulse Width Trigger Shutter Mode ................................................................................................................. 16

9.

Partial Scan Mode .................................................................................................................................................... 17

10.

Remote Interface Function ................................................................................................................................... 18

11.

Initial Settings ..................................................................................................................................................... 19

12.

CMOS Optical Axis Accuracy .............................................................................................................................. 20

13.

Dimensions ......................................................................................................................................................... 21

14.

Cases for Indemnity (Limited Warranty) ................................................................................................................ 22

15.

Sensor Pixel Defect .............................................................................................................................................. 22

16.

Product Support .................................................................................................................................................. 22

©2013 CIS Corporation. All rights reserved.

2

VCC-FC20V49CL Rev.900-723-33-00

1.

Scope of Application

This is to describe VCC-FC20V49CL, high-speed Color CMOS Camera. All specifications contained herein are subject to change without prior notice. Reproduction in whole or in part is prohibited.

2.

Handling Precautions

The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the product.

Please observe all warnings and cautions stated below.

Our warranty does not apply to damages or malfunctions caused by neglecting these precautions. z Do not use or store the camera in the following extreme conditions:

¾ Extremely dusty or humid places.

¾ Extremely hot or cold places (operating temperature –5 to +45 )

¾ Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

¾ Places subject to fluorescent light reflections.

¾ Places subject to unstable (flickering, etc.) lighting conditions.

¾ Places subject to strong vibration. z Remove dust or dirt on the surface of the lens with a blower. z Do not apply excessive force or static electricity that could damage the camera. z Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera

is not in use, put the lens cap on. z Follow the instructions typeapter 7, “External connector pin assignment” for connecting the camera.

Improper connection may cause damages not only to the camera but also to the connected devices. z Confirm the mutual ground potential carefully and then connect the camera to monitors or computers. AC leaks from the connected devices may cause damages or destroy the camera. z Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power supply

voltage may cause damages or malfunction of the camera.

©2013 CIS Corporation. All rights reserved.

3

VCC-FC20V49CL Rev.900-723-33-00 z The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power

supply voltage may cause noises on the video signals. z The rising time of camera power supply voltage shall be less than +10V, Max 60ms.

Please avoid noises like chattering when rising.

9

8

7

12

11

10

10 20 30 40

Voltage Rising Time [ ms]

50 60 70

In case of abnormal operation, contact the distributor from whom you purchased the product.

©2013 CIS Corporation. All rights reserved.

4

VCC-FC20V49CL Rev.900-723-33-00

3.

Notes on Partial Scan Mode Operation

At vertical partial scan mode, the smaller the set reading out lines, the faster the camera exposure and output operation will be. And, at the same time, power consumption will be increased.

Power consumption when the minimum partial scan line number is set will be approx. 2.4W, while it will be approx. 1.6W at full frame scan. That is about 1.5 times higher. With higher power consumption, heat will be increased as well.

We recommend promoting heat dissipation when installing our camera to your system, especially when reading out line is set between the ranges of 50lines to 1line.

For instance, installing the camera to the place under 40 degrees C ambient temperature, or installing the camera to a metalic part, would be effective.

4.

Product Outline

VCC-FC20V49CL is an industrial Color high-speed digital video camera module utilizing a global shutter type,

CMOS sensor. Interface of FC20V49CL complies with camera link (Base Configuration) with its resolution

300K pixels. Clipping part of the image for VGA 1/4 type size, entire pixels can be read out within approx.

1/500s.

Key Features

High frame rate, 502.29 fps, at full frame scan mode with Camera Link Base Configuration.

Frame rate = (pixel clock) / (((horizontal output pixels/output tap number)

+ Horizontal Blanking) × (Vertical Output Lines + Vertical Blanking))

29mm cubic in size (excluding projection).

Camera Link 2Tap output (Base Configuration)

RAW data output 8bit / 10bit selectable

External Trigger

Shutter Speed: 1/500s ~1/50,000s

Fixed Trigger Shutter Mode

Pulse Width Trigger Shutter Mode

Partial Scan Mode (Vertical)

Free sample control software for evaluation purpose only is downloadable via our web.

©2013 CIS Corporation. All rights reserved.

5

VCC-FC20V49CL Rev.900-723-33-00

5. Specification

5.1. General Specification

Item Specification

(1) Pickup Device

Device Type Color CMOS

Effective Pixel Number

640(H) × 480(V)

Unit Cell Size

Chip Size

5.50μm(H) × 5.50μm(V)

3.52mm(H) × 2.64mm(V) (640×5.5μm(H) × 480×5.5μm(V)

Image Circle

φ

4.4mm

4.4

0

2.64

(2) Video output frequency

(3) Sync. system

(4) Video output standard

(5) Resolution

(6) Output Format

(7) Sensitivity

(8) Minimum illumination

(9) Dust or stains in optical system

(10) Power requirements

(11) Power consumption

(12) Dimension

3.52

(Unit: mm)

Pixel Clock

Horizontal Frequency

Vertical Frequency

79.99 MHz

246.12kHz Pixel Clock: 325CLK

Full Frame Scan Mode:

Partial Scan Mode

502.29Hz Scanning Lines: 490H

(Vertical 1/2):

Internal Sync. System

Camera Link 2Tap Output (Base Configuration)

480 TV lines equivalent (VGA size)

RAW data output 8bit/10bit selectable

F2.0 2000lx (Shutter Speed: 1/500s, Gain 0dB)

F1.4 150lx (Shutter Speed: 1/500s, Gain +12dB)

No dust or stain shall be detected on the testing screen with setting the camera aperture at F16.

DC+12V±10% (Max voltage shall not be exceeded +15V.)

Approx. 1.6W at ful frame scan (DC+12V IN).

Approx. 2.4W at partial scan with minimum line number setting (DC DC+12V IN).

Refer to overall dimension drawing (Clause 12)

H:29mm W:29mm D:29mm (excluding projection)

(14) Lens mount

(15) Optical axis accuracy

(16) Gain variable range

(17) White balance

C mount (Refer to overall dimension drawing)

Refer to drawing for CMOS Optical Axis Accuracy (Clause 11)

0~+12dB (Digital Gain:+0.1dB/step)

2800K~9000K(Manual White Balance )(Guaranteed range) adjustment range

(18) Gamma 1(Fixed)

(19) Shutter speed variable range

OFF(1/500),1/750s,1/1000s,1/1500s,1/2000s,1/2500s,1/4000s,1/5000s,1/10000s,1/15000s,

(20) Trigger shutter mode

1/20000s,1/25000s,1/30000s,1/40000s,1/50000s

Fixed Trigger Shutter Mode

Pulse Width Trigger Shutter Mode (Exposure time is set with the pulse width of trigger signal.)

©2013 CIS Corporation. All rights reserved.

6

VCC-FC20V49CL Rev.900-723-33-00

Item Specification

(21) Safety/Quality standards

(22) Durability

(23) Operation environment

(24) Storage environment

UL:

CE:

Conform to UL Standard including materials and others.

Conform to EN55022: 2006 (Class B) for Emmission

Conform to EN61000-6-2: 2005 for Immunity

RoHS:

FCC:

Conform to RoHS

To be applied for FCC Class A Digital Device

This device complies with Part 15 of FCC Rules. Operation is subject to the followiong two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

98m/s

2

(10G)

Frequency

: 20~200 Hz

Vibration

Shock

Temperature

Direction : X,Y,Z 3 directions

Testing time : 120 min for each direction

No malfunction shall be occurred with 980m/s

2

(100G) for ±X, ±Y, and ±Z, 6 directions. (without package)

Operation guaranteed: -5℃~+45℃

Performance guaranteed: 0℃~+40℃

Humidity

RH 20~80% with no condensation

Temperature -25℃ ~ +60℃

Humidity RH 20~80% with no condensation

©2013 CIS Corporation. All rights reserved.

7

VCC-FC20V49CL Rev.900-723-33-00

5.2. Camera Output Signal Specification

Item Specification

(1) Video output data Video Output

LVAL output

FVAL output

DVAL output

(2) Sync. Signal I/O

640 (H) × 480(V)

LVDS

LVDS

LVDS

At Full Frame Scan Mode

Camera Link connector

SP(Exposure) LVDS

HD output LVTTL 6pins Circular connector

VD output LVTTL

Exposure LVTTL

Polarity POSI/NEGA Selectable

(3) Trigger input

Min width of trigger pulse 10μs

Camera Link input LVDS : CC1 input

TTL input LVTTL: No.2 pin

Camera Link connector

6pins Circular connector

V

IH

Min. 2.0V

VIL Max. 0.8V

(4) Serial

Communication

(5) Video output signal

SerTC (Serial to Camera) Camera Link input (LVDS)

SerTFG (Serial to Frame Grabber) Camera Link output (LVDS)

White Clip Level

Digital 8bit :FFh

Setup Level

Digital 8bit :00h

Dark Shading

Digital 8bit :under ±04h for both vertical and horizontal.

(condition: gain 0dB)

5 seconds shall be waited after turning on power to get proper camera operation.

+5.0V(VCC)

HD74LV1GT32ACME

(RENESAS)

Voh 3.8V (Min)

Vol 0.55V (Max)

100Ω

47pF

100Ω

VD,HD

Exposure Output

HD74LV1GT14 ACME

(RENESAS)

Vih 2.0V (Min)

Vil 0.8V (Max)

470pF

1KΩ

Trigger Input

6pins Circular Connector at rear: GPIO interface

©2013 CIS Corporation. All rights reserved.

8

VCC-FC20V49CL Rev.900-723-33-00

5.3.

CMOS Spectral Response (Representative value)

Lens characteristics and illuminant characteristics are not considered.

5.4.

Video Output Format

VGA 500fps Mode: 2Tap Interleaved

Bayer Pattern: GBRG (At full frame scan)

DA

2

DB

2

DA

1

DB

1

From Camera

(2 Tap Output)

DA

0

DB

0

0

1

2

~ ~

0

DA

0

(G)

DA

0

(R)

1

DB

0

(B)

DB

0

(G)

2

DA

1

(G)

DA

1

(R)

3

DB

1

(B)

DB

1

(G)

4

DA

2

(G)

DA

2

(R)

DB

2

(B)

DB

2

(G)

~ ~

Pixels

2047

1087

Lines

*

At manual partial scan mode, Bayer Pattern changes per 1 line according to the set vertical starting position value.

©2013 CIS Corporation. All rights reserved.

9

VCC-FC20V49CL Rev.900-723-33-00

5.5.

Camera Link Port Data Bit Assignment (Base Configuration)

Port/bit

At 8bit output setting At 10bit output setting

Port A0 DA:bit0[LSB]

Port A1 DA:bit1

Port A2 DA:bit2

Port A3 DA:bit3

Port A4 DA:bit4

Port A5 DA:bit5

Port A6 DA:bit6

Port A7 DA:bit7[MSB]

DA:bit0[LSB]

DA:bit1

DA:bit2

DA:bit3

DA:bit4

DA:bit5

DA:bit6

DA:bit7

Port B0 DB: bit0[LSB] DA:bit8

Port B1 DB: bit1

Port B2 DB:bit2

Port B3 DB:bit3

Port B4 DB:bit4

DA:bit9[MSB]

Not in use

Not in use

DB:bit8

Port B5 DB:bit5

Port B6 DB:bit6

Port B7 DB:bit7[MSB]

Port C0 Not in use

DB:bit9[MSB]

Not in use

Not in use

DB:bit0[LSB]

Port C1 Not in use

Port C2 Not in use

Port C3 Not in use

Port C4 Not in use

Port C5 Not in use

Port C6 Not in use

Port C7 Not in use

DB:bit1

DB:bit2

DB:bit3

DB:bit4

DB:bit5

DB:bit6

DB:bit7

©2013 CIS Corporation. All rights reserved.

10

VCC-FC20V49CL Rev.900-723-33-00

6.

Function Settings

Camera functions can be set with serial data communications.

Shutter

(at full frame scan mode)

For partial scan mode, please refer to Section 9.

002

White Balance

Trigger Shutter Mode

Scan Mode

Manual White Balance

R Gain Control

Manual White Balance

B Gain Control

Manual Gain Control

006

007

008

003

004

005

0: 0 dB

1: + 6 dB

3: Manual Gain (Refer to address 008.)

4~255: 0dB

0: 1/500s

1: 1/500s

2: 1/750s

3: 1/1000s

4: 1/1500s

5: 1/2000s

6: 1/2500s

7: 1/4000s

8: 1/5000s

9: 1/10000s

10: 1/15000s

11: 1/20000s

12: 1/25000s

13: 1/30000s

14: 1/40000s

15: 1/50000s

16: Manual Shutter (Refer to address 009&010.)

17~255: 1/500s

0: Through

1: 3200K

2: Spare

3: Spare

4: Manual White Balance (Refer to the Address 006&007.)

5~255: Through

0:

1:

Normal Shutter Mode (Trigger Shutter Mode OFF)

Fixed Trigger Shutter Mode

2:

(Shutter speed can be set with address 002.)

Pulse Width Trigger Shutter Mode

(Shutter speed can be set with trigger pulse width.)

3~255:

Normal Shutter Mode (Trigger Shutter Mode OFF)

0: Full Frame Scan Mode

1: Partial Scan Mode (Vertical 1/2)

2: Manual Partial Scan Mode (Refer to address 016/017 & 019/020.)

3~255:

Full Frame Scan Mode

0~120: 0~+12dB 0.1dB/step ※Make the data of Address 003 to 004.

121~255: +12dB

0~120: 0~+12dB 0.1dB/step ※Make the data of Address 003 to 004.

121~255: +12dB

0~120: 0~+12dB 0.1dB/step ※Set the data of address 001 to 003.

121~255: +12dB

©2013 CIS Corporation. All rights reserved.

11

VCC-FC20V49CL Rev.900-723-33-00

Manual Shutter Control

Trigger Polarity

Input Trigger Port Selection

0~480: 1/50000s~1/500s

481~2047: 480

The setting will be 1 line when 0 is set.

009&010

Exposure Time = The set value × 1line Time [s]

1line Time [s] = ((output pixels/2tap)+5)×1/79.99MHz

At full frame scan, output pixels = 480

1line Time ≒ 4.06μs

Address 002 data shall be 016.

Address 009 MSB and Address 010 LSB make 11bit in total.

0: Positive Input

011

012

2~255:

Positive Input

0: Camera Link Connector 12226-1100-00 PL

1: 6pins Circular Connector

2~255: Camera Link Connector: 12226-1100-00 PL

LVDS

TTL

Output Data Selection

Trigger Input Signals

Camera Internal H Sync ON/OFF

Vertical Partial Scan

Start Position

013

014

0: 8bit output data (RAW)

1: 10bit output data (RAW)

2~255: 8bit output data

2: OFF

3: ON

0~Max. Value ※ 1line/step

Max. value shall be limited according to the formula below.

016&017 480 (Vertical Partial Scan output max. lines – Vertical Partial Scan output lines)

Address 005 data shalla be 002.

Vertical Partial Scan

Output Lines

Remote Communication

Baud Rate Setting

Data Save

019&020

Address 016 MSB and Address 017 LSB make 11bit in total.

0~480:

1line/step Min.:1line/Max :480 lines

481~2047: 480

1 line shall be set when 0 is set.

Address 019 MSB and Address 020 LSB make 11bit in total.

Address 005 data shalla be 002.

030

032

0: 9600bps

1: 19200bps

2: 38400bps

3: 57600bps

4: 115200bps

5~255: 9600bps

Input 083 to save address 000 ~ 031 to EEP-ROM.

©2013 CIS Corporation. All rights reserved.

12

VCC-FC20V49CL Rev.900-723-33-00

7.

External Connector Pin Assignment

7.1.

6pins Circular Connector HR10-7R-6PA (HIROSE) equivalent

Pin No.

1

2

Power IN DC+12V

Trigger IN(TTL level)

3 HD

4 VD

5 Exposure

6 GND

13

26

6

1

2

5

4

3

1

14

7.2.

26pins Mini Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M)

Pin No. Pin No.

1 GND

2 X0-

3 X1-

4 X2-

5 Xclk-

6 X3-

7 SerTC+

8 SerTFG-

9 CC1- (Trigger IN-)

10 CC2+

11 CC3-

12 CC4+

13 GND

14 GND

15 X0+

16 X1+

17 X2+

18 Xclk+

19 X3+

20 SerTC-

21 SerTFG+

22 CC1+ (Trigger IN+)

23 CC2-

24 CC3+

25 CC4-

26 GND

©2013 CIS Corporation. All rights reserved.

13

VCC-FC20V49CL Rev.900-723-33-00

8.

8.1.

Timing Chart

Horizontal Synchronous Signal Timing

Video Output

LVAL Output

DVAL Output

5CLK

5CLK

1

2

3

4

5

6

7

8

1H = 325 CLK

・ ・ ・ ・ ・ ・ ・ ・ ・

320 CLK

320 CLK

8.2.

Vertical Synchronous Signal Timing

8.2.1 Full Frame Scan Mode

Video Output

Exposure Time

LVAL Output

487 488

2 H

489 490 1 2

· · ·

2 H

9 10

490 H

· · · · · · ·

Min. 1H ~ Max. 480 H

11 12

· · · · · · ·

· · · · · · ·

DVAL Output

FVAL Output

10 H

1 2

· · · · · · ·

480 H

Video output signal delays by 2H from Exposure Time.

633 635 637 639

634 636 638 640

1 H

2 H

487 488 489 490

477 478 479 480

CLK 79.99MHz

©2013 CIS Corporation. All rights reserved.

14

VCC-FC20V49CL Rev.900-723-33-00

8.2.2 Fixed Trigger Shutter Mode

This is the mode to start exposure with external input trigger signals, and set the exposure time with

Trigger operation is CLK Sync. HV-Sync Reset. The delay time (Exposure Time Delay) from detecting

trigger edge in the camera to starting exposure is approx. 330ns.

Triggers can be accepted even when outputting video signals. However, trigger signals for exposure

to start the next video output prior to the completion of video transmission for the prior video output

signals cannot be accepted.

If the edge part of trigger signals is overlapped with video outputting period, 1 line noise may be detected on the video output screen. To input trigger signals during video output period, set the data

003 to the address 014 (Trigger input signal, camera internal H sync ON). External trigger signals are synchronized with camera internal H signals so that max. 1HD jitter to Exposure Time delay would occur.

When changing the camera to fixed trigger shutter mode, the first output image can be unstable.

Please input the first trigger as a dummy to ignore and take the second and after as the actual triggers.

Trigger Input

Video Output

Exposure Time

LVAL Output

DVAL Output

FVAL Output

Trigger Input

1

2 H

2 3 4

10 H

11 12 11

1

Exposure Time

Delay(Fixed)

330ns

Exposure Time

(nHD ×4.06μs )

Video output signal delays by 2H from Exposure Time.

12

2

480 H

・ ・ ・ ・ ・

・ ・ ・ ・ ・

・ ・ ・ ・ ・

480 H

491 492

479 480

©2013 CIS Corporation. All rights reserved.

15

VCC-FC20V49CL Rev.900-723-33-00

8.2.3 Pulse Width Trigger Shutter Mode

This is the mode to start exposure with external input trigger signals, and set the exposure time with

pulse width of the trigger signals.

Trigger operation is CLK Sync. HV-Sync Reset. The delay time (Exposure Time Delay) from detecting

trigger edge in the camera to starting exposure is approx. 330ns. And, the delay time from detecting

trigger end edge to completing exposure is approx. 270ns.

Pulse width is min. 1HD to approx. 2 frames. Functionally, there is no upper limitation, but noises

such as dark noises and shadings may be noticeable at long time exposure.

Triggers can be accepted even when outputting video signals. However, trigger signals for exposure to start the next video output prior to the completion of video transmission for the prior video output signals cannot be accepted.

If the edge part of trigger signals is overlapped with video outputting period, 1 line noise may be detected on the video output screen. To input trigger signals during video output period, set the data

003 to the address 014 (Trigger input signal, camera internal H sync ON). External trigger signals are synchronized with camera internal H signals so that max. 1HD jitter to Exposure Time delay would occur.

When changing the camera to pulse width trigger shutter mode, the first output image can be unstable.

Please input the first trigger as a dummy to ignore and take the second and after as the actual triggers.

Trigger Input

480 H

Video Output

・ ・ ・ ・ ・

Exposure Time

2 H

LVAL Output

1 2 3 4 11 12 13 14

・ ・ ・ ・ ・

481 482

DVAL Output

1 2

・ ・ ・ ・ ・

479 480

FVAL Output

10 H

480 H

Trigger Input

Exposure Time

Delay(Fixed)

330ns

Exposure Time

Delay(Fixed)

270ns

※Video output signal delays by 2H from Exposure Time.

©2013 CIS Corporation. All rights reserved.

16

VCC-FC20V49CL Rev.900-723-33-00

9.

Partial Scan Mode

Vertical Partial Scan

· At full frame scan

Video Output

FVAL Output

· At vertical partial scan s+n s+n

-2 -1 s+n

Video Output

Exposure Time

LVAL Output

DVAL Output

FVAL Output

2 H

· · ·

10 H

2 H

0 1 2

· · ·

119 120

Partial scan (vertical 1/2) s: 120H

Manual partial scan s: any s s+1

· · · · · · · n H (Max.)

· · · · · · ·

· · · · · · · n H s: Vertical partial scan starting position (address 016&017) n: Vertical partial scan output lines (address 019&020)

480

· · · s+n

-3 s+n s+n

-2 -1 s+n

2 H

359 360

· · ·

478 479

Partial scan (vertical 1/2) n: 240H

Manual partial scan n: any

Scan Mode (address:005)

0:Full frame scan mode s

0 n

480

Vertical Sync. Frequency (Hz)

502.29

1:Partial scan mode (Vertical 1/2) 120 240 984.49

2:Manual partial scan mode Any any 79.99MHz /((Vertical partial scan output lines +10)×(325))

The max value of vertical partial scan starting position is limited with the formula below since vertical partial scan output line has priority.

The max value of vertical partial scan starting position

=480(The max value of vertical partial scan output line) – Vertical partial scan output lines

(Ex.) When 400 is set as vertical partial scan output lines, the max value of vertical partial scan starting position will be

480-400 = 80.

If vertical partial scan starting position is set to 90 with this time, vertical partial scan output line has priority so that vertical partial scan starting position shall be limited to 80.

0

0 ~ 80

Vertical partial scan

Starting position

Setting range

480

(The max vertical partial scan output lines)

80

90 s = 80 (with limitation)

vertical partial scan

starting position n = 400

The set vertical partial scan

output lines s = 90 (invalid)

vertical partial scan

starting position

Set value

479

At manual partial scan mode, manual shutter value to be set shall meet the following conditions.

The set manual shutter lines ≦ Vertical partial scan output lines

If the condition above is not met, shutter lines to be set will be the same number as vertical partial scan output lines.

©2013 CIS Corporation. All rights reserved.

17

VCC-FC20V49CL Rev.900-723-33-00

10.

Remote Interface Function

Camera can be controlled by external computers and others via camera link interface.

(1)The settings for RS-232C are as follows.

Baud Rate

Data

Stop bit

Parity

XON/XOFF

: 9600bps,19200bps,38400bps,57600bps,115200bps

: 8bit

: 1bit

: None

: not controlled

(2) Control code

The total control code is 14 bits, which conforms to ASCII code.

The control code consists of camera No. process code, remote controller address, remote controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.

1 2 3 4 5 6 7byte目 8 9 10 11 12 13 14

Camera No.

000000: Common No.

Dedicated Camera No.

Process code Remote controller address

“R” Read mode Please refer to

“W” Write mode the address

“C”Camera table of 6. mode

Function setting.

Remote controller data

000~255

CR

0Dh

Camera No

Please send the common code, “000000”, consist of 6 bytes of characters/numeric strings.

The returned data from the camera shall be the dedicated camera No assinged for that specific camera.

Process code

Input any one of R, W, or C to the process code.

R (read mode) is to read the data of remote controller address.

Please be noted to set any dummy data (000~255) to 11 th

~13 th

, since a command shall consists of

14 bytes.

W (write mode) is to write the data to the remote controller address.

Please be noted that the data cannot be saved into EEPROM of the camera.

(Reboot the camera, and the data is reset to the initial setting.)

To save the data into EEPROM, please refer to Clause 5.Function Setting.

Note: Once the data was saved into EEPROM, it may not be reset to t he initial settings.

C is the code to send the data back from the camera.

Note: Do not set code C when sending the data from PC side.

©2013 CIS Corporation. All rights reserved.

18

VCC-FC20V49CL Rev.900-723-33-00

Remote controller address

Note: Do not save the data into the address other than specified, since it may cause the damages or malfunction of the camera.

Remote controller data

Set the decimal number (000~255) for the remote controller data. Please be noted to set any dummy data at read mode.

CR

Be sure to input “CR” to confirm the end of the command.

11.

Initial Settings

White Balance

Trigger Mode

Scan Mode

Manual White Balance

R Gain Control

Manual White Balance

B Gain Control

Manual Gain Control

Manual Shutter Control

Trigger Polarity

Input Trigger Port Selection

Output Data Selection

Trigger Input Signals

Camera Internal H Sync

ON/OFF

Baud Rate

003

004

005

0: Through

0: Normal Shutter Mode (Trigger Shutter Mode OFF)

0: Full Frame Scan Mode

008 0: 0dB

009&010 480: 1/500s

011 0: Positive Input

012

013

0: Camera Link connector (12226-1100-00 PL)

0: 8bit Output Data (RAW)

030 0:9600bps

©2013 CIS Corporation. All rights reserved.

19

VCC-FC20V49CL Rev.900-723-33-00

12.

CMOS Optical Axis Accuracy

6±0.3

29

6±0.3

M2

Inclination of optical axis to datum plane

0.

±

12 29

M2

M3

Datum

Plane

6±0.3

10±0.3

6±0.3

10±0.3

Datum

Plane

Product Label Position ( ? )

0.5

±

°

?? ±0.5°

The center of effective pixels shall be within f 0.6 to the center of C lens mount

Inclination of effective pixels, Theta,?, to datum plane shall be

(*) Dimensions from datum plane to the center of the lens mount

910-006-01-01

(Unit:mm)

©2013 CIS Corporation. All rights reserved.

20

VCC-FC20V49CL Rev.900-723-33-00

13.

Dimensions

29

C

M ou nt

(*

)

2-M2

Depth 3

3-M3

Depth 3

12

4.5

3

Hi-Speed

VGA

41

4.5

29

23.7

(M3 size)

22

(M2 size)

4-M2

Depth 3

DC IN

Product Label Position

*2)C mount screws comply with ANSI/ASME B1.1, 1-32UN(2B).

*1)Screw length from the lens mount surface shall be under 6mm.

And protruding portion shall be less than 10mm.

999-547-00-00

(Unit:mm)

©2013 CIS Corporation. All rights reserved.

21

VCC-FC20V49CL Rev.900-723-33-00

14.

Cases for Indemnity (Limited Warranty)

We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in the following cases.

— In case damage or losses are caused by fire, earthquake, or other acts of God, acts by third party, deliberate or accidental misuse by the user, or use under extreme operating conditions.

— In case indirect, additional, consequential damages (loss of business interests, suspension of business activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from responsibility for such damages.

— In case damage or losses are caused by failure to observe the information contained in the instructions in this product specification & operation manual.

— In case damage or losses are caused by use contrary to the instructions in this product specification & operation manual.

— In case damage or losses are caused by malfunction or other problems resulting from use of equipment or software that is not specified.

— In case damage or losses are caused by repair or modification conducted by the customer or any unauthorized third party (such as an unauthorized service representative).

— Expenses we bear on this product shall be limited to the individual price of the product.

15.

Sensor Pixel Defect

Sensor pixel defects might be noted with time of usage of the products.

Cause of the Sensor pixel defects is the characteristic phenomenon of CMOS itself and CIS is exempted from taking any responsibilities for them.

16.

Product Support

When defects or malfunction of our products occur, and if you would like us to investigate on the cause and repair, please contact your distributors you purchased from to consult and coordinate.

Camera control sample software (RS232C) is downloadable from our web but we shall be exempted from taking responsibility and held harmless for damage or malfunction of your hardware and software caused by using this control software. The purpose of the control software prepared is for you to check operation and evaluate our products. Please be noted that CIS does not customize the program nor provide source code.

©2013 CIS Corporation. All rights reserved.

22

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project