PDX-1700 series manual GB.qxd

PDX-1700 series manual GB.qxd
USERS MANUAL
PDX-1700
series
INTRODUCTION
The PROFOON PDX-1700 series DECT telephones are cordless telecommunication systems, based on the DECT (Digital Enhanced Cordless Telephone)
technology.
The PDX-1700 comes with one handset only. The PDX-17xx models come with
multiple handsets and the model PDX-1715 has a built-in digital answering
machine.
The PROFOON PDX-1700 series DECT telephones are GAP compatible. Up to
6 handsets can be registered to a single base and each handset can be registered to up to 4 bases.
DECLARATION OF NETWORKCOMPATIBILITY
The Profoon PDX-1700 series is designed for use on the ‘public switched telephone networks (analogue single-line)’ of telephone- and cable-companies inside
the European Union.
Each country and/or provider might require a different telephoneplug.
The function Caller-ID is based on both the DTMF and the FSK system (automatic detection). It might be possible that you have to subscribe to this feature.
The Profoon PDX-1700 series complies with the essential requirements and provisions as described in the European Directive 1999/5/EC.
DECLARATION OF CONFORMITY
The declaration of conformity is available
on the website WWW.PROFOON.COM
This telephone is not designed for making emergency telephone calls when the
power fails. Make alternative arrangements for access to emergency services.
SAFETY INFORMATION
1. Please read all the instructions of this manual before using this product.
2. Observe all the instructions marked on this product.
3. Install this product on a stable surface and to avoid anyone from stepping
over the telephone line.
4. Do not fix the AC power supply cord to building surfaces with metal fittings.
5. This product should be operated only from the type of power source
indicated on the product. If you are not sure of the type of power supply to
your home, consult your local power company.
6. Do not use this product near water, or when your hands are wet. If the
product comes into contact with any liquids, disconnect the power supply
immediately and contact repair centre.
7. To prevent fire or electrical shock hazard, do not expose this product to rain
or moisture.
8. Before cleaning the product, disconnect it from the telephone jack and
power source. Use a soft, damp cloth to clean the product. Do not use liquid
cleaner, aerosol cleaners or abrasive powder to clean this product.
9. As there maybe electric shock from lightning, avoid using or installing this
product during thunderstorms.
10. If the product is not operating normally or if it is damaged, do not open the
cabinet or try to repair by yourself. This will void your warranty and also
expose you to dangerous electrical shock or other risks. Please contact
repair centre.
11. Do not use any metallic objects to connect the charging terminals on the
Base Station as this may cause fire due to overloading the power source.
12. Do not charge the battery by any devices other than that provided by this
product.
13. Never use ordinary (non-rechargeable) batteries. Only use approved
batteries of the same type (rechargeable), otherwise battery damage can
result.
14. Dispose the damaged battery properly.
15. Do not touch the uninsulated telephone wires or terminals unless the
telephone line and power source has been disconnected.
16. Do not overload wall outlets and extension cords as this can lead to
electrical shock.
17. Medical equipment can be affected by the handset.
3
TABLE OF CONTENTS
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LCD
................................................ 7
USAGE
to receive a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
preview dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
manual dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 last dialed number memories . . . . . . . . . . . . . . . . . . . . . . . . . .
recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
teleservices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
paging handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
receiving volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
8
8
8
9
9
CALLER-ID:
caller record review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
call back from caller record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
delete specific caller record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
delete all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
time/date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PHONE BOOK:
add entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SETTINGS:
change the base pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ringer melody and volume setting . . . . . . . . . . . . . . . . . . . . . . . . . 14
language setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
key beep setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
call barring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
baby call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
prefix code setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
handset name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUTO ANSWERING (PDX-1715 only):
introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
outgoing message (OGM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
play OGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
answering mode setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4
outgoing message setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
call screen setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
speaker volume setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
answer delay setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
messages playback / erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
erase all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
memo recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
MULTI HANDSET / MULTI BASE:
registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
prioritized ring setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
call transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
conference call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
base selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
de-registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SYSTEM FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PIN-CODE RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
WARRANTYCARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5
INSTALLATION
1. Connect the telephone line cord, one side into the wall socket, another side to
the base station socket.
2. Power-up the base station by connecting the AC power adapter to the mains
socket and another side to the power jack of the base station. The Power
LED at the base station will turn on.
3. Open the handset's battery door and insert the rechargeable battery to the
handset, ensuring correct polarity. Replace the battery door.
Never use non-rechargeable batteries.
4. After 5 seconds, the handset will emit a greet tone to indicate power-up reset
is confirmed. Place the handset to the base station for charging about 10
hours before any operation. The Battery Icon will start to scroll.
NOTE: When the handset battery is fully discharged, the base station will
charge the battery quickly for a few hours and then change to slow charging.
The handset becomes warm during fast charging. This is normal and not
dangerous. It cools down gradually when battery is almost fully charged.
5. The handset is already registered to the base when shipped. The Antenna
Icon should be in steady state to show that the handset is synchronized with
the base. If the Antenna Icon is flashing, press the telephone button to
activate the synchronization.
REMARKS:
1. This product operates at frequency 1.89GHz.
2. Place the base in a high location to ensure a maximum operating range.
3. Do not install the base station in bathrooms.
4. The operating range of the Dect Phone may vary depending on the
environment.
6
LCD
1.
2.
3.
4.
5.
6.
presentation of the name and number
presentation of the day (*)
presentation of the month (*)
presentation of the hours (*)
presentation of the minutes (*)
envelope:
flashes: unread calls in memory
continu on: all calls have been read
1
2
off: no calls in memory
7. handset in program-mode
8. ringer handset is OFF
9. battery:
3 segments on: battery full
2 segments on: battery 2/3 full
1 segment on: battery 1/3 full
0 segment on: battery empty
toggles: batteries are being charged
10. antenna:
flashes: handset is searching for the base
continu on: handset in reach of the base
11. handset in use
*:
6
3
4
5
8
7
10
9
11
Presentation of the time and the date only during the receiving of Caller-ID
and during the reading of the Caller-ID memory.
7
USAGE
TO RECEIVE A CALL:
When the handset is ringing, press any key on the handset and start conversation.
PREVIEW DIALING:
1. Enter the phone number (max. of 20 digits) during standby.
Use button
to edit any wrong entry.
2. If the phone number is correct, press the telephonebutton to dial out that
number. The display will show
and the In Use LED at the base station will
turn on.
After the call is made, the call timer will start to count.
3. Press the telephonebutton to terminate the call or put the handset to the base
station or charger-pod directly. The icon
on the display and the In Use LED
at the base station will turn off.
MANUAL DIALING:
1. If the phone number is more than 20 digits, press the telephonebutton and
then enter the phone number to make the call.
10 LAST DIALED NUMBER MEMORIES:
1. Press ∆ or ∇ button to review the dial-out memory during standby.
The last dial-out phone number will be placed in the first memory. If the
phonenumber matches one in the Phone Book, the corresponding name will
be displayed. There are 10 memories in the dialed list. The memory location
will be shown on the lower left corner of the display.
2. Press
button to dial out the number shown.
3. Once the number is shown, press and hold
button will delete that number.
RECALL:
Recall can be used if you subscribe to an optional "Call Waiting" service from
your local telephone company. If another party calls while you are having a conversation and you hear the special "Call Waiting" tone, press R button to hold the
first call and the second call can be answered.
You may then press R button again to hold the second call and resume your
conversation with the first caller.
TELESERVICES:
Buttons ∗ and # are functionbuttons, needed for divers telecom-services (teleshopping, telebanking, etc) or to control divers telecom devices (PABX, answering
machines, etc). Refer to the concerning manual.
8
PAGING HANDSET:
1. Press the
button on the base, the In-use LED will flash. All the registered
handsets within the operation range will ring and the display will show [BASE]
2. Press the
button on the base again to stop the paging. Or press any key
and button
on a handset to stop the ringing.
RECEIVING VOLUME CONTROL:
During a call you can use buttons ∆ or ∇ to decrease or increase the receiving
volume.
9
CALLER-ID
This telephone is equipped with Caller Display Function, which allows you to
read the caller's name / number before you answer an incoming call. In order to
have this Caller Display Function, you need to subscribe the Caller Display services provided by your local telephone company. Please note that the Caller Display services provided by different telephone companies may not be the same
and some of the features described below may not apply in your district.
There are 30 memories in the Caller Record, with a maximum of 10 characters
for name and 20 digits for phone number in each record. Each caller record
contains the caller's name, number and date / time of receiving that call.
Remarks:
1. If there are several private calls received, the caller record will only store
the latest one.
2. During repeat call, the previous call record of the same number will be
superseded. It will not increase the total number of incoming call in the
Call Record.
CALLER RECORD REVIEW:
1. In standby mode, press OK button. The display will show [NEWXXTOTALXX].
“NEW” represents the number of caller records not yet reviewed.
“TOTAL” represents the total number of memories stored in caller record.
2. Press ∆/∇ button to review the caller record.
3. Press
button to exit.
Remarks:
1. If there is a new call (not yet reviewed), the Message Icon
will flash.
2. When all caller records are reviewed, the display will show the Message Icon
(but not flashing).
3. If it is a repeat call, the display will show [1234567 >>], press button ∇ will
show [<<XX REPEAT] in which XX represents the number of calls repeated.
CALL BACK FROM CALLER RECORD:
Once you have found the desired name/number, press x button to dial out that
number.
Attention:
In case you are connected behind a PABX and you must first dial a -0-, than you
might program this -0- as a prefix. Please refer to chapter PREFIX CODE SETTING on page 16).
10
DELETE SPECIFIC CALLER RECORD:
1. Once you have found the desired name/number, press
show [DELETE?].
2. Press OK button to delete the record.
3. Press
button to exit.
, the display will
DELETE ALL:
1. In standby mode, press OK button. The display will show [NEWXXTOTALXX].
2. press
, the display will show [DELETE?].
2. Press OK button, the display will show [DELETE ALL?].
3. Press OK button to confirm.
Remarks:
1. Caller records which have not yet been reviewed, cannot be deleted
TIME/DATE:
With each call, the time and date will be registered. In case you receive Caller-ID
from a FSK based system, this system will provide the time and the date.
In case you are connected to a DTMF based system, the telephone makes use
of the time and the date you have set. Please refer to chapter ‘time and date’ on
page 17.
11
PHONE BOOK
There are 20 memories for the PHONE BOOK. You may store a name (with 10
characters) and a phone number (with 20 digits) into each memory.
Three basic operations are: ADD ENTRY, EDIT/DELETE, SEARCH.
ADD ENTRY:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [PHONEBOOK].
3. Press OK button to confirm the selection and the display will show [SEARCH].
4. Press ∆/∇ button to select [ADD ENTRY].
5. Press OK button to confirm the selection and the display will show [NAME?].
6. Press OK button to confirm the selection and the display will show [_
].
7. Enter the name (max. 10 characters) and press OK button.
8. Enter the phone number (max. 20 digits ) and press OK button.
9. Repeat from step 5 for more entries or press
to exit this mode.
notes:
Press # button and keep it pressed until the display shows [P] to insert a dialpause.
The counter on bottom left will show the memory location (e.g. 01/20). If more
than 20 entries are added, the display will show [MEM FULL]
The order of memory is name first in alphabetical order then followed by number
(If no name is stored with that number) in ascending order.
EDIT:
To change name / number stored in Phone book:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [PHONEBOOK].
3. Press OK button to confirm the selection and the display will show [SEARCH].
4. Press ∆/∇ button to select [EDIT].
5. Press OK button to confirm the selection.
6. Press ∆/∇ button to select the desired entry and press OK button
7. Press
button to delete the name and enter the new name, press OK button
8. Press
button to delete the number, enter the new number and press OK
9. Repeat from step 5 for more corrections or press
to exit this mode.
DELETE:
1. Follow the above section (EDIT) step1 to step 3 to select the memory to be
deleted.
2. Press
button and the display will show [DELETE?]
3. Press OK button to delete the memory.
12
SEARCH:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [PHONEBOOK].
3. Press OK button to confirm the selection and the display will show [SEARCH].
4. Press OK button to review the Phone Book.
The first name, according to the alphabetical order, will be displayed. (If the
Phone Book is empty, handset will emit an error tone.
5. Press ∆/∇ button to select the desired entry and press
to dial the number.
13
SETTINGS
CHANGE THE BASE PIN:
Base PIN (Personal Identification Number or Personal Security Code) is a fourdigit code to protect the base from illegal registration and access.
The factory default PIN-code is 0000.
1.
2.
3.
4.
5.
Press
button to enter menu mode during standby.
Press ∆/∇ button to select [SYSTEM].
Press OK button to confirm and the display will show [CHANGE PIN].
Press OK button to confirm and the display will show [BS PIN ----].
Enter the old PIN by pressing the corresponding keys.
If the old PIN is correct, the display will show [NEW ----].
6. Enter the four-digit new PIN, then the display will show [CONFIRM ----].
Re-enter the same new PIN for confirmation.
7. Press OK button to exit.
Remarks:
* The PIN-code must be a 4-digit code.
* Refer to chapter PINCODE-RESET on page 26 in case you forgot your PINcode.
* The PIN-code is the same for all registered handsets.
RINGER MELODY AND VOLUME SETTING:
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [ MELODY].
3. Press OK button to confirm and the display will show [MEL 1]
The handset will emit the Melody1 tone.
Press ∆/∇ button to select different melodies. There are three types of
melody: MEL1, MEL2 and MEL3.
Press OK button to confirm the selection.
4. If the melody is selected , the display will show [MEL x: HIGH].
5. Press ∆/∇ button to select different volume: HIGH, LOW or OFF.
6. Press OK button to confirm the selection and exit.
If OFF is selected, the Ringer Off Icon will turn on.
LANGUAGE SETTING:
1. Press
to enter the menu mode during standby.
2. Press ∆/∇ to select [LANGUAGE ] (TAAL).
3. Press OK button to confirm and the display will show [DUTCH].
4. Press ∆/∇ to select the desired language.
5. Press OK button to confirm the selection and exit.
14
KEY BEEP SETTING:
You may select to turn on or off the keypad tone.
1. Press button
to enter menu mode during standby.
2. Press ∆/∇ button to select [KEY BEEP].
3. Press OK button to confirm and the display will show [BEEP ON?]
4. Press ∆/∇ button will toggle between [BEEP ON ?] and [BEEP OFF?]
5. Press OK button to confirm the selection and exit.
CALL BARRING:
Call Barring is to prohibit certain telephonenumbers to be dialed out if the first
one to four digits of such phone numbers match with the Barring Number1 or
Barring Number2.
Store the Barring numbers:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [CALL BARING].
5. Press OK button to confirm, the display will show [BS PIN ----].
6. Enter the base PIN (factory setting: 0000). If the base PIN is correct , the
display will show [BARRING OFF?].
7. Press ∆/∇ button to select [BAR NUMBER1?].
8. Press OK button to confirm the selection and the display will show
[NUM0 ----].
9. Enter 1 to 4 digit Barring Number1 and press OK button to confirm and exit.
Follow the same procedures to program Barring Number 2.
Call Barring On/off:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [CALL BARING].
5. Press OK button to confirm, the display will show [BS PIN ----].
6. Enter the base PIN (factory setting: 0000). If the base PIN is correct , the
display will show [BARRING OFF?].
7. Press ∆/∇ button and select:
[BARRING: ON?] to activate the feature
[BARRING: OFF?] to disactivate the feature
8. Press OK button to finish and exit.
15
BABY CALL:
This feature is specially designed for the little kids (or old people) to make an
emergency call by pressing any single key. When this function is turned on, any
key-press (except OK button and
button) during standby will dial out the Baby
Call number only.
Store the number:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [BABY CALL].
3. Press OK button to confirm the selection, the display will show [CALL: OFF]
4. Press ∆/∇ button to select [NUMBER?].
5. Press OK button to confirm the selection, the display will show [_
] (or a
previous stored number, erase it with the
button).
6. Enter the Baby Call number. (max. of 20 digits).
7. Press OK button to finish and exit.
Baby Call On/off:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [BABY CALL].
3. Press OK button to confirm the selection, the display will show [CALL: OFF]
4. Press ∆/∇ button and select:
[CALL: ON?] to activate the feature
[CALL: OFF?] to deactivate the feature
5. Press OK button to finish and exit.
Notes:
The Baby Call cannot be turned on if no Baby Call number is programmed.
Make sure the Baby Call number does not match with the Barring Number1 and
Number2.
PREFIX CODE SETTING:
When you select Prefix Code dialing, a Prefix Code will be inserted in front of
any telephone number dialed out (including memory dialing).
Before activating this function, you have to program the Prefix Code first.
Store the Prefix Code:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [PREFIX CODE].
5. Press OK button to confirm, the display will show [PREFIX OFF?].
6. Press ∆/∇ button to select [NUMBER?].
7. Press OK button to confirm the selection.
8. Enter the Prefix Code. (max. of 8 digits).
9. Press OK button to confirm and exit.
16
Prefix Code On/off:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [PREFIX CODE].
5. Press OK button to confirm, the display will show [PREFIX OFF?].
6. Press ∆/∇ button and select:
[PREFIX: ON?] to activate the feature
[PREFIX: OFF?] to deactivate the feature
7. Press OK button to finish and exit.
HANDSET NAME:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [HANDSET NAME] and press OK button to confirm
3. Press
to erase the present name and to move the cursor to the left.
4. Use the dialbuttons to insert the new name.
5. Press OK button to confirm and exit.
TIME AND DATE:
In case you are connected to a FSK based system, together with the Caller-ID,
the provider sends the time and the date of the call. In case you are connected
to a DTMF based system, you have to program the time and date manually.
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [SET CID TIME].
5. Press OK button to confirm, the display will show “HH:MM 00:00”
6. Enter the time through the keyboard (2 digits for the hours and 2 digits for
the minutes).
7. After some seconds the display will show “yy 00”.
8. Enter the last 2 figures of the year.
9. After some seconds the display will show “DD/MM 01/01”.
10. Enter the date through the keyboard (2 digits for the date and 2 digits for
the month).
11. Press OK button to confirm and exit.
Attention: the LCD only shows the time and date during the receiving of Caller-ID
and during the reading of the Caller-ID memory.
17
AUTO ANSWERING (PDX-1715 only)
INTRODUCTION:
* When the Answer Mode is set to ON, the number of rings for the system to
answer a call could be selected as 2, 4, 5 or toll saver.
* When the Answer Mode is set to OFF, the number of rings for the system to
answer a call is 8 for user to use remote access.
* When the system runs out of memory, LCD will show [ANS FULL]. The
system will change to Answer-Only mode until some messages are deleted.
* When the predefined number of rings is received, the system will engaged the
line within 200ms after the last valid ring is ended. The system will pause for
1s and then play the OGM followed by a long beep to indicate ICM recording
is started.
* During ICM recording, the speaker will be mute or unmute depending on the
setting of Call Screen.
* ICM recording will stop as well for the following events:
A. A valid security code is detected (Line Remote Access)
B. Long period of silence (7s)
C. Long call progress tones
D. The TALK key is pressed (Call Intercept).
E. The memory is full
(Total record time: 10 min. Max. number of messages: 50).
F. ICM max. record time (54s) is reached.
OUTGOING MESSAGE (OGM):
The OGM is the text the caller will hear when the call is answered. Separated
OGM’s can be recorded for the modes ‘ANSWER RECORD’ and ‘ANSWER
ONLY’.
1. ANSWER-RECORD: the system will answer the call and the caller may leave
a message
2. ANSWER ONLY: the system will answer the call but after playing the OGM,
the line will be disconnected
Record OGM:
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [OGM].
5. Press OK button and press ∆/∇ button to select [RECORD OGM].
6. Press OK button and press ∆/∇ button to select [ANS-RECORD?] or
[ANSWER ONLY?].
7. Press OK button and the LCD display will show [RECORDING...].
Recording is through the handset microphone
Press OK button to stop recording or it will stop automatically when the
max. OGM record time (33s) is reached.
18
The red LED in the base unit will flash slowly at the beginning and flash
quickly at the last 5s of recording.
The OGM's cannot be deleted but they can be overwritten.
PLAY OGM:
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [OGM].
5. Press OK button and press ∆/∇ button to select [PLAY OGM].
6. Press OK button and press ∆/∇ button to select [ANS-RECORD ?] or
[ANSWER ONLY ?].
7. Press OK button to play the OGM record, the LCD will display [PLAYING...]
8. Press OK button to stop playing.
ANSWERING MODE SETTING: (Factory default is Answer Off)
1. press button 7 for 2 seconds
2. press ∆/∇ button to select [ANSWER-ON?] or [ANSWER-OFF?].
3. Press OK button to confirm and exit to previous menu.
through menu:
1. Press button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [SETUP].
5. Press OK button to confirm and the display will show [ANSWER MODE].
6. Press OK button and press ∆/∇ button to select [ANSWER-ON?] or
[ANSWER-OFF?].
7. Press OK button to confirm and exit to previous menu.
REMARKS:
- ANSWER-ON: the system will answer and record Incoming Message or the
system will answer but not record Incoming Message.
- After you choose ANSWER-ON, the default handset name will change to:
"ANS.ON".
- ANSWER-OFF: the system will not answer.
OUTGOING MESSAGE SETTING: (Factory default is Answer-Record mode)
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [OGM].
5. Press OK button to confirm and the display will show [SET OGM MODE].
6. Press OK button and press ∆/∇ button to select [ANS-RECORD?] Or
[ANSWER ONLY].
7. Press OK button to confirm and exit to previous menu.
19
CALL SCREEN SETTING: (Factory default is Enable)
(If Answer Record mode is chosen, select "Ans Record" to get the Call Screen)
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [SETUP].
5. Press OK button and press ∆/∇ button to select [CALL SCREEN].
6. Press OK button and press ∆/∇ button to select [ENABLE ?] or
[DISABLE ?]
7. Press OK button to confirm and exit to previous menu.
REMARKS:
- [ENABLE]: OGM and ICM will be routed to the loudspeaker in the base
unit.
- [DISABLE]: OGM and ICM will not be routed to base speaker.
SPEAKER VOLUME SETTING: (Factory default is High Level)
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [SETUP].
5. Press OK button and press ∆/∇ button to select [SPEAKER VOL].
6. Press OK button and press ∆/∇ button to select [HIGH?], [LOW?] or [OFF?]
7. Press OK button to confirm and exit to previous menu.
ANSWER DELAY SETTING: (Factory default is 4 ring)
1. Press button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [SETUP].
5. Press OK button and press ∆/∇ button to select [ANSWER DELAY].
6. Press OK button and press ∆/∇ button to select [2 RING?], [4 RING?].
[5 RING?] or [TOLL SAVER?]
7. Press OK button to confirm and exit to previous menu.
REMARKS:
When [TOLL SAVER] is selected, the system will answer a call after 2 rings if
there are unread new messages, otherwise it will answer the call after 5 rings.
20
MESSAGES PLAYBACK / ERASE:
1. Press button 1 for 2 seconds in standby mode.
The LCD displays [NEWxx TOTALyy]
Where xx represents the number of new messages and yy represents the
total number of messages.
2. Press OK button to start message playback.
3. Press "6" key to skip to the next message
4. Press "4" key once to repeat the current message
5. Press "4" key twice within 1s to skip to the previous message.
6. Press
button to erase the message which is playing
7. Press OK button at any time to stop.
REMARKS:
- If there are new messages (unread), the system plays the new message only,
otherwise it will play all old messages.
- During message playback, the corresponding number and time of receiving
will be shown.
- After all messages are finished, the system will return to standby mode.
ERASE ALL:
1. Press button 1 for 2 seconds in standby mode.
The LCD display [NEWxx TOTALyy].
2. Press
button, the LCD display [DELETE ALL?]
3. Press OK to delete all old messages. (unread messages cannot be deleted)
The LCD display [MSG DELETED].
MEMO RECORDING:
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [RECORD MEMO].
5. Press OK button and the LCD display will show [RECORDING...].
Recording is through the handset microphone.
6. Press OK button to stop recording or it will stop automatically when the max.
memo record time (1min.) is reached.
21
REMOTE CONTROL:
Line Remote Access:
Any phone with tone dialing function can be used to call the PDX-1715 and
check Incoming Messages in a remote way.
After the PDX-1715 answers the call and OGM is playing, enter the 4 digits
security code to enter the Remote mode.
Attention: When the remote access code=0000, line remote access is disable.
User must enter other 4 digits code in order to enable the line remote access.
Remote Access Code Setting: (Factory default code is 0000)
1. Press
button to enter the menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm and the display will show [ANSWERER].
4. Press OK button and press ∆/∇ button to select [SETUP].
5. Press OK button and press ∆/∇ button to select [SECURITY].
6. Press OK button to confirm and enter 4 digits code.
7. Press OK button to confirm and exit to previous menu.
Table for operation of DTMF code:
Function
Message Playback
Skip to next message
Back to previous message
Repeat current message
Delete current message
Stop all operation but not release the line
Stop all operation and release the line
DTMF Code
1
6
4+4
4
3
5
9
REMARKS:
If there are new messages (unread), the system plays the new message only,
otherwise it will play all old messages.
22
MULTI HANDSET / MULTI BASE
This product is GAP COMPATIBLE, providing advanced optional features:
* EACH BASE STATION CAN REGISTER 6 HANDSETS
* EACH HANDSET CAN BE REGISTERED TO 4 BASE STATIONS
* INTERCOM/ CALL TRANSFER / CONFERENCE CALL FOR MULTI
HANDSETS
* RING PRIORITY
Remark:
Handset/base registration to other brands of DECT Phone is possible provided
that they are GAP COMPATIBLE.
(Note: If base1 is already registered , it will be overwritten by the new registration)
REGISTRATION:
Although the handset(s) which came with this product is/are already registered to
the base from the factory, it can be registered again to the same base to change
its handset number or in case it was registered to other base(s).
There can be six handsets registered to one base. Registration is performed
when both the handset and base are in standby mode:
Base:
1. Press and hold the button on the base for 6 seconds, the In-use LED will
flash (Time allowed for registration will be 2 minutes).
Handset:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [REGISTER].
3. Press OK button to confirm, the display will show [BASE: 1234].
For an un-registered handset, all digits are flashing.
If the digit is steady, it means the handset is already registered to that base.
4. Press key -1- to select base1, the display will show [BS PIN ----].
(Note: If base1 is already registered, it will be overwritten by the new
registration)
5. Enter the four digits base PIN. (the default PIN is 0000)
6. The display will show [WAITING...], the handset is now searching a base that
is prepared for registration.
7. When the base is located, the display will show [HS 123456].
(or if there is another handset(s) already registered to this base e.g. handset 1
and handset 3, the display will become [HS _2_456])
8. Press the desired numerical key to set the handset number, the handset and
the base will go into standby mode.
23
PRIORITIZED RING SETTING:
If more than one handset are registered to a base, the ring sequence can be
programmed:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [RING SEQ].
5. Press OK button to confirm, the display will show [HANDSET: ∗]
6. Press the desired numeric key to select a particular handset to ring first (press
∗ for no ring priority).
7. Press OK button to confirm and exit.
Note:
If the selected handset number is not yet registered, there will be an error tone.
The selected handset will ring first, if the user does not answer the call in 2 rings,
other handset(s) will start to ring.
INTERCOM:
If there are two or more handsets registered to a base, a toll-free intercom conversation is possible within the base operation range.
1. Press
button on one of the handsets during standby
The Line Icon
will turn on and the display will show [CALL WHAT?]
2. Press the handset number which you want to call.
For instance, handset 1 calls handset 2 then the display on handset 1 will
show [CALL 2 ] while the display on handset 2 will show [CALL FROM 1]
3. Handset 2 will ring.
4. Press
button to answer the call.
Both handsets now enter the Intercom mode.
Press
button on either handset to exit the intercom mode.
CALL TRANSFER:
When a handset is making a call, it can transfer the call to other handset(s) within the base operation range.
1. During the telephone conversation, press the
button, the line will be put on
hold.
2. Enter the handset number, the called handset will ring.
3. On the called handset, the user must press the xx button to answer the call.
4. When the call is answered, you may press the
button to transfer the call to
the other handset.
After instruction 2, you may directly press the
button to transfer the call without inquiry. If the called handset does not answer the call within 30 seconds,
the call will be transfered back to your handset.
24
CONFERENCE CALL:
Any handset can make a conference call with the outside party and another
handset within the base operation range.
1. During the telephone conversation, press the
button, the line will be put on
hold.
2. Enter the handset number, the called handset will ring.
3. On the called handset, the user must press the
button to answer the call.
4. When the call is answered, press the # button to start the conference call
(press the
button in case the called party does not answer)
At the end of the call, both handsets must press the
button.
BASE SELECTION:
Each handset can be registered to four bases. If the handset is registered to
more than one base, one can choose the specific base manually or if the Auto
mode is selected, the handset will automatically locate to the nearest registered
base.
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SELECT BASE].
3. Press OK button to confirm, the display will show [AUTO 1 2 3 4] (if only 2
bases are registered, the display will show [AUTO 1 2 _ _], the current
selection is in steady form while other(s) is/are flashing).
4. Press the desired numeric key to select a particular base or press button -0to select AUTO .
5. Press OK button to confirm and exit.
DE-REGISTRATION:
In standby mode, you may de-register the handset(s) from the base:
1. Press
button to enter menu mode during standby.
2. Press ∆/∇ button to select [SYSTEM].
3. Press OK button to confirm.
4. Press ∆/∇ button to select [DE-REGISTER].
5. Press OK button to confirm, the display will show [BS PIN ----].
6. Enter the base PIN (factory setting: 0000). If the base PIN is correct, the
registered handset number(s) will be displayed, e.g. handset1 and handset2
are registered, the display will show [HS:12____ ]
7. Press the handset number to deregister that handset.
The de-registered handset will display [UNREGISTER].
SYSTEM FAILURE
In case of a possible system failure, please remove the battery-pack from the
handset(s) and disconnect the power adapter and telephone connectioncord
from the corresponding wall outlets. Wait several minutes and reconnect all. If
this does not help, than please consult your dealer.
25
PIN-CODE RESET
In case you forgot your PIN-code, than act as follow:
1. Press and hold the
button on the base for about 6 seconds until the In-use
LED starts to flash, than release this button.
2. Press again this button for about 6 seconds until the In-use LED starts
flashing rapidly, than release this button.
3. Now press this button momentarily, now the PIN-code is returned to 0000.
Attention: with this reset procedure, all extra handsets are now de-registered.
You may have to register them again as decribed on page 23.
MAINTENANCE
· Do not clean any part of your telephone with benzene, thinner or other solvent
chemicals - this may cause permanent damage that is not covered by the
guarantee. When necessary, clean it with a damp cloth.
· Keep your telephone away from hot, humid conditions or strong sunlight.
· Every effort has been made to ensure the highest standards of reliability for
your PDX-1700 series DECT telephone. However, if something does go
wrong, please do not try to repair it yourself - consult your supplier.
· Do not use your telephone outdoors in the rain, or handle it with wet hands water can damage electrical equipment.
· Exhausted batteries may never be disposed of in household waste but
must be handed in at your local depot for chemical waste.
TECHNICAL SPECIFICATIONS
Standard
Frequency range
Channel bandwidth
Modulation
Speech encoding
Communication range
Handset power supply
Operating time
Operating temperature
Storage temperature
DECT (Digital Enhanced Cordless
TeleCommunications )
1.88 to 1.9 GHz (bandwidth = 20 MHz)
1.728 MHz
GMSK
Adaptive Differential Pulse Code Modulation
(ADPCM) at 32 kbit/s
Up to 300m in open space
Up to 50 m in buildings
rechargeable batterypack, 3x AAA, NiMH,
3.6V 700mAh
Standby: > 100 hours
Talking: > 6 hours
0°C to 40°C
-20°C to 60°C
26
WARRANTYCARD
Name:
Address:
Zipcode:
City:
Telephone:
Modelnumber:
Serialnumber:
Attach here your
purchase ticket
You have a guarantee of 24 MONTHS after the date of purchase of this Telephone. We guarantee during this period the free repair of defects caused by material- and construction faults. This at the importers discretion. It is only possible to
claim to the guarantee when you enclose your purchase ticket with the PDX1700 series DECT telephone.
HOW TO ACT:
If you notice a defect, consult the manual first. If this manual gives you no definite answer, consult your dealer with a clear description of your complaint. He will
collect the device together with this guarantee card and the dated purchase ticket and he will take care of a prompt repair, respectively free sending to the
importer.
THE GUARANTEE EXPIRES:
When used inexpert, faulty connections, use of unoriginal parts or accessories,
negligence and defects caused by fire, flood, stroke of lightning and natural disasters. With unqualified modifications or repairs by third persons. With incorrect
transport without a suitable packing. If the device is not handed in with the correct filled in guarantee card and the purchase ticket.
NOT UNDER THIS GUARANTEE: cords, plugs and batteries.
All further responsibilities, in particular subsequent damages, are excluded.
27
0681
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement