F Series Indoor IP User`s Manua

F Series Indoor IP User`s Manua
HD Fisheye Panorama Network Camera Quick Start Guide
Version 1.2.3
i
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series
product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and
the Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power
supply requirement is subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for
emergent power off when necessary.
Please prevent the line cord from being trampled or pressed, especially the plug, power
socket and the junction from the device.
Note: Do not connect these two power supplying sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted
repair.
2.Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus;
otherwise it may cause overexposure (It is not the device malfunction), which will affect
the longevity of CCD or CMOS.
Please transport, use and store the device within the range of allowed humidity and
temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely
cold and with strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please do not allow rain or damp to the indoor device in case fire or lightning may occur.
Please keep the sound ventilation in case of heat accumulation.
Please pack the device with standard factory packaging or material with same quality
when transporting the device.
i
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
3. Operation and Daily Maintenance
Please do not touch the heat dissipation component of the device directly in order to
avoid scald.
Please do not dismantle the device; there is no component which can be fixed by users
themselves in the machine. It may cause water leakage or bad image for the device due
to unprofessional dismantling.
It is recommended to use the device with thunder proof device in order to improve
thunder proof effect.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean
the dust or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away
the dust gently if it is necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use
the water to dilute the mild detergent first and then use it to clean the device. Finally use
the dry cloth to clean the device. Don’t use volatile solvent like alcohol, benzene, thinner
and etc or strong detergent with abrasiveness, otherwise it will damage the surface
coating or reduce the working performance of the device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to deal with once dirt is found:
Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton
cloth or paper soaked with alcohol or detergent to wipe from the lens center to outward. It
is ok to change the cloth and wipe several times if it is not clean enough.
Warning
Please use the standard accessories provided by manufacturer and make sure the
device is installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser
beam device.
Please do not provide two or more power supply modes for the device, otherwise it may
cause damage to the device.
Statement
ii
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded
content will be added in the manual without prior announcement.
Please contact the supplier or customer service if there is any problem occurred when
using the device.
Please contact the customer service for the latest procedure and supplementary
documentation.
There may be deviation between the actual value of some data and the value provided in
the manual due to the reasons such as the real environment is not stable and so on.
Please refer to the company’s final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by
the manual.
Note:
Please refer to the disk for more details, check and download corresponding user’s
manual and tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
iii
Table of Contents
1
2
3
Structure ................................................................................................................ 1
1.1
Device External Cable ........................................................................... 1
1.2
Dimensions.............................................................................................. 1
1.3
Alarm Setup............................................................................................. 2
Installation ............................................................................................................. 4
2.1
Device Installation .................................................................................. 4
2.2
Micro SD Card Installation .................................................................... 5
Network Configuration ......................................................................................... 7
3.1
Modify IP Address .................................................................................. 7
3.2
Login WEB Interface .............................................................................. 8
ii
1 Structure
1.1 Device External Cable
Figure 1- 1
The device external cable is shown in Figure 1- 1.
Please refer to Sheet 1-1 for corresponding information about external cable functions.
NO.
Port
Port Name
Connector
Function Description
AUDIO
OUT
Audio output
1
RCA
Output audio signal to the speakers.
2
AUDIO IN
RCA
Input audio signal, receive the analog audio signal
from the sound pick-up.
3
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
4
I/O
I/O port
-
Connect I/O port
5
POWER
Power input
port
-
Connect DC 12V power, input power
port
Audio input
port
Sheet 1-1
1.2 Dimensions
Note:
There are two standards for side dimension of the device, which are: 33.7mm, 47.7mm and
36.6mm, 50.7mm. Please refer to the actual product model for more details.
You can refer to the following figures for dimension information. The Unit is mm. See Figure 1-2 and
Figure 1-3.
1
Figure 1-2
Front Side
Bottom Side
Figure 1-3
1.3 Alarm Setup
Please refer to Figure 1-4 for more information about alarm setup.
Figure 1-4
Please follow the steps listed below for alarm input and output connection.
2
Step 1
Step 2
Step 3
Step 4
Connect alarm input device to the alarm input of I/O cable.
Connect alarm output device to the alarm output of I/O cable, alarm output is collector open
circuit output which connects 10K resistor to 3.3V externally.
Open the Web, set alarm input and output correspondingly. Alarm input on WEB
corresponds to I/O cable on device. When there is alarm, alarm input device will generate
signal of high and low level. Set corresponding NO and NC inputs.
Set the WEB alarm output. The alarm output is for the alarm output port of the device. It is the
alarm output port of the I/O cable.
Alarm input, output figures:
Figure 1-5
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to 3.3V or it is idle, the device collects the
logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 1-6
When alarm output is OC, it needs to increase pull-up resistance externally to work normally; output
signal is high and low level. After external pull-up resistance is increased, the default of output signal is
high level, and it switches to low level when there is alarm output.
The working current of alarm output port is recommended as <= 10mA. The max current which is used
to drive external circuit is 80mA, it is advised to add a relay if it is beyond the value.
3
2 Installation
Important



The network camera can be put on the surface to monitor, it can also use bracket to install on the
ceiling, which means there are three kinds of installation modes which are ground mount, ceiling
mount and wall mount. The following chapter is an example of ceiling mount installation.
Before you complete the installation and debugging, do not remove the electrostatic attraction film
on the transparent enclosure. Otherwise it may result in injury. After removing the electrostatic
attraction film, don’t touch dome enclosure in case it may leave stain.
Before the installation, please make sure the installation surface can sustain at least 3X weight of
the bracket and the camera.
2.1 Device Installation
Installation Position Map
Ceiling Mount Effect
Wall Mount Effect
Figure 2-1
4
Figure 2-2
Step 1
Take the installation position diagram from the accessories bag and then paste it on the installation
ceiling or the wall according to the monitor area.
Step 2
Please dig three bottom holes of the plastic expansion bolts according to the diagram. If you need to
dig a hole to pull through the cable on top of installation surface, you need to dig a cable exit hole of no
less than 28MM on the installation surface according to the installation positioning diagram, which
makes the network cable go through.
Step 3
Insert 3 expansion bolts from the accessories bag into the bottom holes and lock them firmly, adjust
the position of device installation pedestal and pull the cable through the cable exit hole on the
installation surface.
Step 4
Aim 3 screw fixed holes on the installation chassis to 3 plastic expansion bolt fixed holes on the
installation surface, then tighten 3 ST3 self-tapping screws into 3 plastic expansion bolts and fasten
them firmly, fix the installation chassis on the installation surface.
Step 5
When installing dome body, find the little gap on the dome body and make it corresponding to the
“TOP” direction on the installation chassis, rotate the dome body in clockwise direction and secure it
firmly. So far, installation is completed.
Note:
If connect the host GND to ground lead, it may improve device reliability. The GND locates next to exit
hole on the rear side of the chassis and the GND screw is M2.5.
2.2 Micro SD Card Installation
Use the cross screwdriver to unfasten and take down 2screws on the SD card cover, find the Micro SD
card slot position according to the following figure then fasten back the 2 screws on SD card cover
after the Micro SD card is inserted.
5
Note:


The SD card cover is related to the device waterproof, make sure to put the silica gel ring of the
SD card cover back to the waterproof groove and tighten the two screws.
The time of changing SD card should be controlled within 4 hours; otherwise it will cause
desiccant failure and abnormities such as water mist and etc.
Figure 2-3
6
3 Network Configuration
The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in order
to make the camera get access to the network smoothly, please plan the useable IP segment
reasonably according to the actual network environment.
3.1 Modify IP Address
IP address can be acquired and modified through quick configuration tool for the cameras which are
accessed via wired network, it needs to connect wired network to configure wireless parameters
before using wireless network cameras. In this chapter, it will introduce the approach of modifying IP
address via “Quick Configuration Tool”; also you can modify the IP address in the network parameters
of the WEB interface, please refer to the document in the disk << WEB Operation Manual>> for more
details.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same network
segment with computer IP address.
Step 1 Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2 Double click the device to be configured, the system will pop out the “Login” dialog box. Enter
the IP address, user name, password and port number of the camera, and click “Confirm”.
Note:
The default user name and password are admin and admin respectively, the default of port is
37777. See Figure 3-1 for more details.
7
Figure 3-1
Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finish modification.
See Figure 3-2 for more details.
Figure 3-2
3.2 Login WEB Interface
Note:
Different devices may have different WEB interfaces, the figures below are just for reference, please
refer to the document <<WEB Operation Manual>> in the disk and the actual interface for more details
Step 1 Open IE and input the modified camera IP address in the address bar.
Step 2 The login interface is shown below, please input your user name and password (Default user
name is admin and password is admin respectively), click “login”.
See Figure 3-3 for more details.
8
Figure 3-3
Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main interface.
Please modify the administrator password as soon as possible after you successfully logged in.
Figure 3-4
9
Note
 This user’s manual is for reference only. Slight difference may be found in user
interface.
 All the designs and software here are subject to change without prior written
notice.
 All trademarks and registered trademarks mentioned are the properties of their
respective
owners.
 If there is any uncertainty or controversy, please refer to the final explanation of
us.
 Please visit our website for more information.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement