Analog Interface Module
Module d’interface analogique
Analog-Schnittstellenmodul
Modulo interfaccia analogica
Módulo de interface analoga
(Cat 1492-AIFM8-3, -RAIFM8-3)
To prevent electrical shock, disconnect from power source before installing or servicing. FM Class 1, Div.2 requires
device installation in a tool-accessible enclosure compliant with ANSI/ISA S82.
AVERTISSEMENT Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toutes décharges. FM Classe 1, Div. 2
nécessite l'installation de l'équipement dans une armoire accessible aux interventions, conforme à ANSI/ISA S82.
Vor Installations- oder Servicearbeiten Strom-versorgung unterbrechen, um Elektroschocks zu vermeiden. FM-Klasse 1,
WARNUNG
Gruppe 2 erfordert die Installation des Gerätes in einem Gehäuse, das für Werkzeuge zugänglich ist und den
Anforderungen gemäß ANSI/ISA S82 entspricht.
Per prevenire infortuni, togliere tensione prima dell’installazione o manutenzione. FM Classe 1, Divisione 2 richiede
AVVERTENZA
l'installazione del dispositivo in un alloggiamento con capacità di accesso per strumenti conforme allo standard
ANSI/ISA S82.
Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. El
ADVERTENCIA
requisito de FM (Factory Mutual) Clase 1, Div. 2, establece que el dispositivo debe instalarse en un envolvente que
permita la introducción y uso de herramientas y cumpla con la norma ANSI/ISA S82.
WARNING
13
1
SH
25
= D-Connector Pin Number
= Numéro de broche du connecteur D
= D-Steckstift-Nummer
= Numero di pin del connettore a D
= Número de patillas del conector D
Module Identification Area.
Identification du module
Modulkennzeichnungsbereich
Area per l'identificazione del modulo
Area de identificación del módulo
= Field-side Terminals
= Borne exterieure
= Feldseitiger Terminal
= Terminale lato-campo
= Terminal de campo
B
1
A
1
1492-EJA35
35 mm DIN Rail
199-DR1
199-DR4
1492-DR7
1
Adhesive Label Card. Provides terminal wiring identification.
Carte étiquette adhésive. Identifie le câblage des bornes.
Aufklebbare Etiketten zur Kennzeichnung der Klemmenverdrahtung.
Scheda etichette adesive. Fornisce l'identificazione del cablaggio dei terminali.
Tarjeta de etiquetas adhesivas. Proporciona identificación de cableado del terminal.
PN-104504
DIR 40063-326 (Version 11)
Printed in U.S.A.
Lower = A
Upper = B
1
Removable Terminal Block
Installation / Removal
Montage / Retrait
Installation / Entfernen
Montaggio / Smontaggio
Instalación / Extracción
Module
Installation / Removal
Montage / Retrait
Installation / Entfernen
Montaggio / Smontaggio
Instalación / Extracción
1
1
3
3
1492-N90
1492-N90
2
2
3.5-4.5 lb-in
(0.38-0.50 Nm)
0.32 in
(8 mm)
3.5-4.5 lb-in
(0.38-0.50 Nm)
0.32 in
(8 mm)
W
H
#22-#12 AWG
(0.2-4 mm2)
Cu only
Cuivre seulement
Nur Kupfer
Solo Cu (rame)
Solamente Cu
Applies to modules with fixed and
removable (R) terminal block
PN-104504
DIR 40063-326 (Version 11)
#22-#12 AWG
(0.2-4 mm2)
Cu only
Cuivre seulement
Nur Kupfer
Solo Cu (rame)
Solamente Cu
Applies to modules with
removable terminal block plugs (1492-RAIFM_)
(2)
Cable Matrix
Tableau des câbles
I/O Module
Module E/S
E/A-Modul
Modulo I/O
Módulo de E/S
(Voltage)
(Tension)
(Spannung)
(Tensione)
(Voltaje)
(Current)
(Courant)
1746-NI16V (Strom)
(Corrente)
(Corriente)
1746-NO8I
1746-N08V
1492-AIFM8-3
1492-RAIFM8-3
1492-ACABLE
1746-NI8
1746-NI16I
Kabelmatrix
Matrice dei cavi
(Voltage)
(Tension)
(Spannung)
(Tensione)
(Voltaje)
(Current)
(Courant)
(Strom)
(Corrente)
(Corriente)
(Single-ended Voltage)
(Tension assymétrique)
1756-IF8
(Asymmetrische Spannung)
TC-IAH081 (Tensione asimmetrica)
(Tensión asimétrica)
1492-ACAB
1492-ACAB
1
1
A46
A46
1492-ACABLE
I/O Module
Module E/S
E/A-Modul
Modulo I/O
Módulo de E/S
C
1
1492-ACABLE
Matriz de cables
1
1
1756-IF16
TC-IAH161
1492-AIFM8-3
1492-RAIFM8-3
(Differential Current)
(Courant différentiel)
(Differentialstrom)
(Corrente differenziale)
(Corriente diferencial)
(Voltage)
(Tension)
1756-OF8
(Spannung)
TC-OAV081
(Tensione)
(Voltaje)
1769-OF8
(Voltage)
(Tension)
(Spannung)
(Tensione)
(Voltaje)
1492-ACABLE 1 WA
1492-HWACAB 1 WA
1771-IFE
(Differential)
(Différentiel)
(Differential)
(Differenziale)
(Diferencial)
1492-ACABLE
1
E
1771-IFE
(Single-ended)
(Assymétrique)
(Asymmetrische)
(Asimmetrica)
(Asimétrica)
1492-ACABLE
1
F
1771-IFF
(Differential)
(Différentiel)
(Differential)
(Differenziale)
(Diferencial)
1492-ACABLE
1
E
1771-IFF
(Single-ended)
(Assymétrique)
(Asymmetrische)
(Asimmetrica)
(Asimétrica)
1492-ACABLE
1
F
1771-IL
1492-ACABLE
1
H
1794-IE4XOE2
1794-IE8
1794-IF2XOF2I
1794-IF4I
1794-OE4
1794-OF4I
1492-ACAB
1756-OF8H (Current Output Hart Protocol)
1492-ACABLE
1
WB
1756-OF8H (Voltage Output)
1492-ACABLE
1
(Current)
(Courant)
1756-OF8
(Strom)
TC-OAV081
(Corrente)
(Corriente)
1492-ACABLE 1 WB
1492-HWACAB 1 WB
R
WA
R
1492-ACABLE 1 TA
1492-HWACAB 1 TA
1769-IF8
1492-ACAB
1492-ACABLE 1 TB
1492-HWACAB 1 TB
(Differential Voltage)
(Tension différentiel)
1756-IF8
(Differentialspannung)
TC-IAH081
(Tensione differenziale)
(Tensión diferencial)
1769-IF8
1492-ACAB
1
1492-ACABLE 1 TC
1492-HWACAB 1 TC
(Single-Ended Current)
(Courant assymétrique)
(Asymmetrische Strom)
(Corrente asimmetrica)
(Corriente asimétrica)
EB69
(Differential Current)
(Courant différentiel)
1756-IF8
(Differentialstrom)
TC-IAH081
(Corrente differenziale)
(Corriente diferencial)
1492-ACABLE 1 TD
1492-HWACAB 1 TD
1769-IF8
(Differential Voltage)
(Tension différentiel)
(Differentialspannung)
(Tensione differenziale)
(Tensión diferencial)
1492-ACAB
1
EC69
1769-IF8
(Differential Current)
(Courant différentiel)
(Differentialstrom)
(Corrente differenziale)
(Corriente diferencial)
1492-ACAB
1
ED69
(Differential Current)
(Courant différentiel)
1769-IF16C (Differentialstrom)
(Corrente differenziale)
(Corriente diferencial)
1492-ACAB
1
EE69
(Voltage)
(Tension)
1769-IF16V (Spannung)
(Tensione)
(Voltaje)
1492-ACAB
1
EE69
1756-IF8H
1756-IF8H
(Current Input Hart Protocol)
(Voltage Input)
(Single-ended Voltage)
(Tension assymétrique)
1756-IF16
(Asymmetrische Spannung)
TC-IAH161
(Tensione asimmetrica)
(Tensión asimétrica)
1492-ACABLE
1492-ACABLE
1
1
UD
UC
1492-ACABLE 1 UA
1492-HWACAB 1 UA
1756-IF16
TC-IAH161
(Single-Ended Current)
(Courant assymétrique)
(Asymmetrische Strom)
(Corrente asimmetrica)
(Corriente asimétrica)
1492-ACABLE 1 UB
1492-HWACAB 1 UB
1756-IF16
TC-IAH161
(Differential Voltage)
(Tension différentiel)
(Differentialspannung)
(Tensione differenziale)
(Tensión diferencial)
1492-ACABLE 1 UC
1492-HWACAB 1 UC
PN-104504
DIR 40063-326 (Version 11)
1492-AIFM8-3
1492-RAIFM8-3
1492-ACABLE 1 UD
1492-HWACAB 1 UD
(Single-ended Voltage)
(Tension assymétrique)
(Asymmetrische Spannung)
(Tensione asimmetrica)
(Tensión asimétrica)
(Single-Ended Current)
(Courant assymétrique)
1756-IF8
(Asymmetrische Strom)
TC-IAH081 (Corrente asimmetrica)
(Corriente asimétrica)
I/O Module
Module E/S
E/A-Modul
Modulo I/O
Módulo de E/S
1
EA69
(Current)
(Courant)
(Strom)
(Corrente)
(Corriente)
1492-ACAB
1
1
D69
Z94
Cables are available in 0.5m, 1.0m, 2.5m and 5.0m lengths (005=0.5m, 010=1.0m, 025=2.5m, 050=5.0m).
Custom length cables also available. Contact local Sales Office for more information.
Câbles disponibles en 0,5m, 1,0m, 2,5m et 5,0m de longueur (005=0,5m; 010=1,0m; 025=2,5m; 050=5,0m).
Câbles sur mesure à la demande. Contactez e bureau le plus proche.
Verfügbare Kabellängen 0,5m, 1,0m, 2,5m und 5,0m (005=0,5m; 010=1,0m; 025=2,5m; 050=5,0m).
Anwenderspezifizifische Längen stehen ebenfalls zur Verfügung. Kontaktieren Sie bitte Ihr lokales Vertriebsbüro für weitere
Informationen.
I cavi sono disponibili in lunghezze di 0,5m, 1,0m, 2,5m e 5,0m (005=0,5m; 010=1,0m; 025=2,5m; 050=5,0m).
Sono disponibili anche cavi su misura. Per ulteriori informazioni, contattare l’ufficio vendite locale.
Cables disponibles en longitudes de 0,5m, 1,0m, 2,5m, 5,0m (005=0,5m; 010=1,0m; 025=2,5m; 050=5,0m).
Hay disponibles cables de varias longitudes. Para más información comuníquese con la oficina de ventas.
Supports Removable Terminal Block (RTB) plug. Compatible screw style plug, 1492-RTB16N (pkg. qty. 2).
Compatible push-in style plug 1492-RTB16P (pkg. qty. 2). Order plugs separately.
Cable is limited for use within the control panel unless it is run through conduit. Cable is ITC (Instrumentation Tray Cable) rated.
(3)
Cable Shield
Installation
Installation du
câble blindé
Kabelabschirmungs
Installation
Installazione
schermo del
cavo
Instalación de
pantalla de
cable
NOTICE
Refer to your PLC modules Installation Manual for unique grounding requirements
REMARQUE
Voir le manuel d'installation de vos modules PLC pour les conditions uniques de mise à la masse.
HINWEIS
Informationen zu besonderen Erdungsanforderungen finden Sie im Installationshandbuch für PLC-Module.
NOTA
Per requisiti specifici di messa a terra consultare il manuale di installazione dei moduli PLC.
AVISO
Consulte el manual de instalación de módulos PLC para conocer los requisitos sobre la conexión única a tierra.
PLC Analog Module
Shield
Blindé
Abschirmung
Schermo
Pantalla
1492-ACABLE 1 YY
1492-ACAB 1 XX
Earth Ground
Masse Terre
Erdung
Messa a terra
Tierra
Drain
Drain
Drain
Drenaggio
Drenaje
NOTICE
Refer to Publications 1770-4.1 for generally recommended wiring and shield grounding guidelines.
REMARQUE
Voir les publications 1770-4.1 pour les conseils généraux de mise à la masse des câbles blindés.
HINWEIS
Sehen Sie Publikationen 1770-4.1 DE für generell empfohlene Verdrahtungs- und Abschirmungsanweisungen.
NOTA
Per procedure di cablaggio e messa a terra dello schermo generalmente consigliate consultare le pubblicazioni 1770-4.1.
AVISO
Consulte las publicaciones 1770-4.1 para obtener las recomendaciones más comunes sobre cableado y pautas para conexión a tierra.
To ground Cable Shield at chassis:
Pour mettre à la masse le câble blindé sur le chàssis:
Zur Erdung der Kabelabschirmung am Gehäuse:
Per mettere a terra lo schermo del cavo sul telaio:
Para hacer tierra con protector de cable en el chassis:
PLC
Analog
Module
10-32 x .312 Thread Roll Type TT Screw (included with cable)
Vis Type TT à filetage roulé 10-32 x ,312 (fournie avec le càble)
US-NR. 10-32 x ,312 Gewindeschraube Typ TT (wird mit Kabel geliefert)
Vite tipo TT Thread Roll 10-32 x ,312 (inclusa con il cavo)
Barra roscada de 10-32 x 0,312 Tipo de tornillo TT (incluído con cable)
1492-ACABLE YY
1492-ACAB 1 XX
1
PN-104504
DIR 40063-326 (Version 11)
(4)
Pinout
Brochage
Anschlußbelegung
Disposizione dei piedini
Esquema de pins
1492-AIFM8-3
1492-RAIFM8-3
3
B1
2
B2
1
B3
14
B4
15
B5
16
B6
17
B7
18
B8
12
B9
13
B10
25
B11
24
B12
23
B13
22
B14
20
B15
21
B16
4
6
8
10
19
A9
A10
A11
A12
A13
A14
A15
A16
SH
A1
A2
A3
A4
A5
A6
A7
A8
I/O Wiring Data
NOTICE
Wiring information for your I/O module, AIFM module and cable (e.g. wiring diagram and pinouts)are available online at www.rockwellautomation.com/en/e-tools.
To obtain information follow this procedure.
1) In the Catalog Number BOX at the above online site type in the catalog number of the IFM, AIFM, etc. module you are using and click on Submit.
2) At the next screen displayed, click on the Modify key (lower left of screen).
3) Click on the areas that indicate NO SELECTION and enter your specific configuration information (e.g. I/O platform, I/O MODULE, ETC.). NOTE: To obtain the
wiring diagram, you must select th Pre-Wired Cable Connector selection.
4) Configure your 1492 cable by filing in the NO SELECTION areas.
5) Click on the ACCEPT key for the configured 1492 cable. At the next screen click on ACCEPT for the 1492 module.
6) At the next screen (Configuration Results) displays the results of your specific configuration. The "supplementary Documents" column contains I/O wiring information
for the configuration (e.g. I/O Wiring Diagrams).
PN-104504
DIR 40063-326 (Version 11)
(5)
Specifications
Spécifications
Technische Daten
Specifiche
Especificaciones
Catalog No.
Référence
Bestell-Nr.
N. Catalogo
Referencia
Voltage
Tension
Spannung
Tensione
Voltaje
1492-AIFM8-3
1492-RAIFM8-3
Current / Circuit
Courant / Circuit
Strom / Schaltkreis
Corrente / circuito
Intensidad / circuito
0 - 132V AC / DC
2 Amps
Maximum Recurring Peak Voltage Tension de crele réurrente maximale
Maximale periodische Hochstspannung
Tensione massima di cresta ricorrente
Voltaje de cresta iterativo máximo
Catalog No.
Référence
Bestell-Nr.
N. Catalogo
Referencia
1492-AIFM8-3
1492-RAIFM8-3
600 Vp Current / Module
Courant / Module
Strom / Modul
Corrente / modulo
Intensidad / módulo
#Terminals / Shield Common
Nbre bornes / blindage commun
Anzahl der Terminals / Abschirmungsmasse
#Terminali / comune dello schermo
#Terminales / Protector común
12 Amps
Humidity
Humidité
Feuchtigkeit
Humedad
Umidità
0° C - 60° C
8
Approx. Shipping Weight
Poids d'embarquement approximatif
Ungefähres Versandgewicht
Peso approssimativo del carico
Peso aproximado al momento de
embarque
5 - 95% Operating Temperature Range
Plage températures de fonctionnement
Betriebstemperaturbereich
Limiti temperatura di funzionamento
Rango de temperatura de funcionamient
.64 lb.
(289 g)
Dimensions
Dimensions
Abmessungen
Dimensioni
Dimensiones
Standards
Normes
Standards
Standard
Estándares
cULus (File: E10314, Guide No. NRAG)
Suitable for use in Class 1 Div 2 Groups A,
B, C and D Hazardous and Non-Hazardous
4.33 in. (110 mm) W Locations.
3.27 in. (83 mm) H Temperature Code = T3C at 60°C 2.74 in (69.5 mm) D CE: Compliant for all applicable directives
FM Class 1 Div 2 Groups A, B, C and D
Temperature Rating T3C = 60°C (J.I. 3000590,
all except relay modules)
For transients > 600 Vp use a UL recognized suppression device rated at 2.5 kV withstand.
Pour des transitoires > 600 Vp utilisez un dispositif de suppression certifié UL à 2,5 kV nominal de tenue.
Für Einschaltstöße > 600 Vp verwenden Sie einen UL anerkannten Entstörer, der bewertet wurde bei 2,5 kV standzuhalten.
Per transitori > 600 Vp usare dispositivo di soppressione riconosciuto da UL capace di sopportare 2,5 kV.
Para transitorios > 600 Vp use un dispositivo de supresión reconocido UL clasificado con 2,5 kV.
Non-condensing
Sans condensation
Nicht kondensierend
Senza condensa
sin condensación
Power, input and output (I/O) wiring must be in accordance with Class I Division 2 wiring methods - Artticle 501-10(B)(1) of the National Electrical Code.
WARNING Explosion Hazard - substitution of components may impair suitability for Class I Division 2.
Explosion Hazard - Do Not Disconnect Equipment unless power has been switched off or the area is known to be Non-Hazardous.
Add 0.39 in. to the width dimension for 1492-Rxx type modules.
SURGE SUPPRESSION follow the literature recommendations of the PLC module being used.
La section SUPPRESSION DES SURTENSIONS se trouve à la suite de la littérature qui contient les recommandations relatives au module PLC utilisé.
ÜBERSPANNUNGSSCHUTZ Bitte beachten Sie die Dokumentationsempfehlungen für das jeweils benutzte SPS-Modul.
Per la SOPPRESSIONE DEI PICCHI TEMPORANEI, seguire le istruzioni riportate nella documentazione in dotazione al Modulo PLC utilizzato.
SUPRESIÓN DE SOBRETENSIÓN, siga las recomendaciones indicadas en la documentación del módulo PLC respectivo.
Reference Publications: Refer to 1770-4.1 and appropriate PLC I/O module installation manual.
PN-104504
DIR 40063-326 (Version 11)
Printed in U.S.A.
">
