dvd player sd5010ky
DIGITAL VIDEO
DVD PLAYER
SD5010KY
OWNER’S MANUAL
© 2010 Toshiba Corporation
Introduction
2
Connections
14
Basic playback
19
Function setup
23
Others
27
Introduction
SAFETY PRECAUTIONS
CAUTION: VISIBLE LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM.
AVIS
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
CLASS 1
LASER PRODUCT
The symbol for Class
(Double lnsulation)
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Dangerous high
voltages are present inside the enclosure. Do not open the cabinet. Refer servicing to qualified personnel only.
CAUTION: This Digital Video Disc Player employs a Laser System. To ensure proper use of this product, please read
this owner’s manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized
service location.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
WARNINGS
• The main plug is used as disconnect device and it should remain readily operable during intended used. In order to
disconnect the apparatus from the mains completely, the main plug should be disconnected from the mains socket
outlet completely.
• The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use.
• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall
be placed on the apparatus.
• Minimum 10 cm (4 inches) distances around the apparatus for sufficient ventilations.
• The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths,
curtains, etc.
• No naked flame sources such as lighted candles should be placed on the apparatus.
• The use of apparatus in moderate climates.
Location of the required label
The rating plate and the
safety caution are on
the rear of the unit.
2
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
2.
Keep these instructions.
3.
Read all warnings.
4.
Follow all instructions.
5.
Do not use this appliance near water.
6.
Clean only with a dry cloth.
7.
Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Introduction
1.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Portable Cart
Warning
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
14. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire
or electric shock.
15. Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled
with liquid, or candles on top of the unit.
16. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.
17. Do not place anything on top of this unit.
18. Do not place the apparatus on amplifiers or equipment that may produce heat.
19. Never block or cover the slots or openings in the unit.
Never place the unit:
• on a bed, sofa, rug or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, built-in cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the unit from overheating and to help maintain reliable operation.
20. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal
injury and apparatus malfunction.
21. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet.
Wait until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause
fire.
22. During thunderstorms, do not touch the connecting cables or the apparatus.
23. Warning: To prevent spread of fire, keep candles or other open flames away from this product at all times.
3
Introduction
PRECAUTIONS
Notes on handling
When shipping the DVD player, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was originally
packed at the factory. Take care not to give it a shock or
shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic products
in contact with the DVD player for a long time. They will
leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is not a
malfunction.
When the DVD player is not in use, be sure to remove
the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on and
use the DVD player occasionally.
Notes on locating
Place the DVD player on a level surface. Do not use it on
a shaky or unstable surface such as a wobbling table or
inclined stand. The loaded disc may come off the proper
position and cause damage to the DVD player.
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD
player away from the TV, radio, or VCR.
Notes on moisture condensation
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when you pour
a cold drink into a glass on a warm day. Drops of water form
on the outside of the glass. In the same way, moisture may
condense on the optical pick-up lens inside this unit, one
of the most crucial internal parts of the DVD player.
Moisture condensation occurs during the following
cases.
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe it
dry.
Do not use any type of solvent, such as thinners and
benzene, as they may damage the surface of the DVD
player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Inspection and Maintenance
This DVD player is a high technology, precision device.
If the optical pick-up lens and disc drive parts become
dirty or worn down, the picture quality may be reduced.
To avoid reduction in picture quality, it is recommended
that regular inspection and maintenance (cleaning or
parts replacement) be performed every 1,000 hours of
use. For further details, contact your nearest consumer
electronics dealer.
4
Do not use the DVD player when moisture
condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player will
have warmed up and evaporated any moisture. Keep the
DVD player connected to the wall outlet and moisture
condensation will seldom occur.
NOTES ON DISCS
On VIDEO CDs
On handling discs
Playback side
Do not attach paper or tape to discs.
This DVD player supports VIDEO CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback variations
depending on types of discs.
Introduction
Do not touch the playback side of the disc.
• VIDEO CD not equipped with PBC function (Version
1.1)
Sound and movie can be played on this DVD player in
the same way as an audio CD.
• VIDEO CD equipped with PBC function (Version
2.0)
In addition to operation of a VIDEO CD not equipped with
the PBC function, you can enjoy playback of interactive
software with search function by using the menu
displayed on the TV screen (Menu Playback). Some of
the functions described in this owner’s manual may not
work with some discs.
Notes on region numbers
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc clean.
The region number of this DVD player is 4. If region
numbers, which stand for their playable area, are printed
on your DVD and you do not find 4 or
, disc playback
will not be allowed by the player. (In this case, the DVD
player will display a message on-screen).
Notes on copyright
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for
vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
The unauthorized recording, use, distribution, or revision
of copyrighted materials including, without limitation,
television programs, videotapes, and DVDs, is prohibited
under the Copyright Laws of the United States and other
countries, and may subject you to civil and criminal
liability.
This product incorporates copyright protection technology
that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
5
Introduction
NOTES ON DISCS
Playable discs
About this owner’s manual
This DVD player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
Audio
+
video
(moving
pictures)
DVDs
12 cm
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
VIDEO
CDs
DIGITAL VIDEO
Audio
CDs
SUPER
VIDEO
CDs
DivX®
Audio
+
video
(moving
pictures)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
Audio
+
video
(moving
pictures)
12 cm
35 min.
8 cm
10 min.
Audio
+
video
(moving
pictures)
12 cm
Audio
SUPER VIDEO
Approx. 160 minutes
(double sided disc)
8 cm
It depends on DivX®
quality
The following discs are also available.
DVD±R/±RW and DVD-ROM discs of DVD format
CD-R/CD-RW discs of CD-DA, Video CD, MP3 or JPEG
format
DivX Certified® to play DivX® video, including premium
content
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or non-standardized
discs, etc., even if they may be labeled as above.
• This DVD player uses the NTSC/PAL colour system, and
cannot play DVDs recorded in any other colour system
(SECAM, etc.).
Because of problems and errors that can occur during the
creation of DVD and CD software and/or the manufacture
of DVD and CD discs, Toshiba cannot assure that this DVD
player will successfully play every disc bearing the DVD
and CD logos. If you happen to experience any difficulty
playing a DVD and/or CD disc on this DVD player, please
contact Toshiba Customer Service.
is a trademark of DVD Format/Logo Licensing
Corporation.
6
This owner’s manual explains the basic instructions of
this DVD player. Some DVDs are produced in a manner
that allows specific or limited operation during playback.
As such, the DVD player may not respond to all operating
commands. This is not a defect in the DVD player. Refer
to instruction notes of discs.
” may appear on the TV screen during operation.
“
” means that the operation is not permitted by the
A“
DVD player or the disc.
About
The
icons on the heading bar show the
playable discs for the function described under that
heading.
DVD : You can use this function with DVD discs.
: You can use this function with Video CDs.
CD : You can use this function with Audio CDs/CD-R/RW
CDs.
Table of Contents
Introduction
Function setup
2
3
4
5
Notes on region numbers ................................... 5
Table of Contents ...................................... 7
Identification of Controls ......................... 8
Front panel ...........................................................8
Rear panel ...........................................................8
DVD display ........................................................8
Customizing the Function Settings.......... 23
Using the Language setup menu ........................23
Using the Video setup menu ...............................23
Using the Audio setup menu ...............................24
Using the Parental Lock setup menu ..................25
Using the TV System setup menu.......................25
Introduction
SAFETY PRECAUTIONS ...........................
IMPORTANT SAFETY INSTRUCTIONS ....
PRECAUTIONS ..........................................
NOTES ON DISCS .....................................
Others
Before Calling Service Personnel............. 27
Specifications............................................. 28
Using the Remote Control ........................ 9
Loading batteries .................................................9
Operating with the remote control ........................9
Remote control ..................................................10
Names and functions .........................................11
Connections
Connecting to a TV ................................... 14
Connecting to a TV (Using the phono type jacks) . 14
Connecting to a display (Using a HDMI® cable) ........15
Connecting to Optional Equipment ........ 16
Connecting to an amplifier equipped with a
Dolby® Digital decoder ...................................... 16
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ................................. 17
Connecting to an amplifier equipped with a
DTS® decoder ................................................... 17
Connecting to an amplifier equipped with an
MPEG2 audio decoder ..................................... 18
Connecting to an amplifier equipped with a
digital audio input .............................................. 18
Basic playback
Playing a Disc ........................................... 19
Basic playback .................................................. 19
Playing MP3/DivX®/JPEG Files................. 20
Playing MP3/DivX®/JPEG Files ......................... 20
Using USB Device ..................................... 22
Connecting to USB flash drive ......................... 22
MP3 Converter (converting CD to USB device) ... 22
7
Introduction
Identification of Controls
See the page in
for details.
Front panel
HDMI indicator 15
19
11
12
9
8
12
11
HDMI SELECT
15
USB jack
22
Rear panel
14
Power Cord
HDMI OUT
jack
15
VIDEO
L
R
COAXIAL DIGITAL
HDMI OUT
ANALOG
14
16
17
18
DVD display
The indicators vary depending on the kinds of discs you play.
No disc
8
Bad disc
OPEN
DVD VIDEO
VIDEO CD
Audio CD
• During playback:
Example
• During playback:
Example
• During playback:
Example
Some discs may only
display chapter numbers.
Some discs may only
display track numbers.
Some discs may only
display track numbers.
LOAD/CLOSE
USB
Power off
Title/Chapter/Track
number Indicator
• In USB mode
with no USB
device connected:
Multifunctional indicator
(indicates operating
status or messages, etc.)
Using the Remote control
Loading batteries
Open the cover.
2
Insert batteries (R03/AAA size).
Introduction
1
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Make sure to match the + and – on the batteries to
the marks inside the battery compartment.
Caution
• Never throw batteries into a fire.
Notes
• Be sure to use R03/AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries
in combination.
• Always remove batteries from remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid
from leaking into the battery compartment.
• Battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
* Do not expose the remote sensor of the DVD player
to a strong light source such as direct sunlight or
other illumination. If you do so, you may not be able
to operate the DVD player via the remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode
of operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot
or humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
9
Introduction
Using the Remote control (continued)
Remote control
The instructions in this manual describe the functions on the remote control. See the page in
1.
2. ON/STANDBY button 11
11
3.
for details.
11
18. SEARCH (T) button 12
4.
5.
11
MUTE
11
SUBTITLE/MP3 CONV.
6.
11
7.
11
8.
11
8.
11
9.
11
9.
25.
11
10.
11.
12.
13.
11
27.
28.
29.
11
11
TV SYSTEM
15.
12
26.
11
11
14.
12
DVD
USB
30.
31.
32.
13
13
13
*13
13
13
13
16. TV SYSTEM button 12
33. HDMI button 13
17. DVD button 12
34. USB button 13
* RETURN button
Return to menu display for VCD (2.0) discs with menu
(PBC should be ON).
10
19. MUTE button 12
20.
12
21. SUBTITLE/MP3 CONV. button 12
22.
12
23.
12
24.
12
* MENU button
Use the MENU button to display the menu included on
many DVDs.
Names and functions
1. OPEN/CLOSE button
• Press the button to open/close the disc tray.
• The function is the same as the OPEN/CLOSE button on
the front panel.
3. Number buttons
Press number buttons to play relevant chapter/track.
4. E.A.M button (Enhanced Audio Mode)
Use to select the sound enhancement on or off.
3D*:
To obtain expansive virtual surround sound effects from
two speakers. To use this enhancement on sounds output
from the ANALOG AUDIO OUT jacks, be sure to set
“Digital out” to “PCM”.
* Effective in playback of a DVD .
Notes
• Actual effects to sounds may vary depending on the speaker
system. Make selection according to your preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD player is connected to an amplifier
equipped with Dolby Surround Pro Logic, select “3D
effect”. Otherwise, Dolby Surround Pro Logic may function
differently than usual.
• The sound effect might not be heard easily on small TVs.
• The sound effect can be heard more easily at higher
volume.
• The sound effect might take a few seconds to be heard
after turning on the E.A.M.
5. E.P.M button (Enhanced Picture Mode)
Use to select the picture enhancement.
Brightness 1
6
12
Contrast
6
12
1
Select the picture enhancement by pressing / , then
press / to make your selections.
To exit the picture enhancement selection, press E.P.M
again.
To locate succeeding chapters or tracks.
To locate preceding chapters or tracks.
9. REV/FWD buttons
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or FWD button, the playback
speed changes.
10. Direction buttons
Use / / / to select a selection in setup menu.
11. TOP MENU button
Display the title menu on DVD.
12. PLAY MODE button
While playing a disc, press the PLAY MODE button
repeatedly to select a repeat mode.
For DVD:
- Repeat Chapter (currently playing chapter)
- Repeat Title (currently playing title)
- Repeat All (entire disc)
- Off (cancel)
For Video CD, Audio CD:
- Repeat Single (currently playing track)
- Repeat All (entire disc)
- Off (cancel)
For MP3, JPEG, DivX®:
- Repeat Single (currently playing file)
- Repeat Folder (current folder)
- Repeat All (all files)
- Off (cancel)
Note
For VCD with PBC on, you cannot select a repeat
mode.
Note
Actual effect to picture may vary depending on the TV.
Make selection according to your preference.
13. CLEAR button
Use CLEAR to delete the scheduled program or to cancel
input data in setting mode.
6. ANGLE button
• While playing a scene recorded with multiple angles, press
the ANGLE button.
Number changes to show the number of the current angle.
(The maximum number of possible angles is 9)
14. MEMORY button
• Press this button, the program screen is displayed as
below:
e.g. DVD
e.g. VCD/Audio CD
:
[ 1/3
ANGLE button is also used to rotate the picture in
clockwise direction during JPEG playback.
Note
This function can only be used for discs on which scenes
shot from multiple angles have been recorded. If only one
angle is recorded, “ ” will be displayed.
7. PAUSE/STEP button
• Press PAUSE/STEP to freeze playback.
• During still playback, press PAUSE/STEP advance the
picture frame by frame.
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
[- -]
Clear
Chapter number
Title number
[- -]
[- -]
Clear
Track number
• Select the items in the order you want by pressing the
number buttons.
Each time you press the / / / button, the space
is highlighted in turn. Highlight where you want to enter,
then press the corresponding number buttons.
11
Introduction
2. ON/STANDBY button
Turn the unit on or set the unit to standby mode.
8. SKIP buttons
Introduction
Names and functions (continued)
To change the programmed selections, use
/ / / to move the highlighted bar to the item
you want to change and press CLEAR, then input
the new number.
• Press / / / to move the highlighted bar to
,
then press PLAY or ENTER to start playback.
• To resume normal playback from memory playback,
use / / / to move the highlighted bar to “Clear”,
then press ENTER. All the input programs will be
cleared.
Press PLAY button to resume normal playback.
Notes
• Some discs may not permit memory playback
operation.
• If you select repeat during memory playback, the DVD
player repeats the current memory playback.
• The programmed selections will be cleared when you
open the disc tray or turn off the DVD player.
15.SETUP button
Access the on-screen Setup menu for settings
adjustment.
16. TV System button
Press to select TV system (NTSC, PAL or Auto)
26
.
17.DVD button
Press to select the DVD mode if it is in the USB mode.
18.SEARCH (T) button
• Press SEARCH (T) and use / to move the cursor
to the title (TT) / chapter (CH) / track (TRK) / time.
e.g.
DVD TT
CH
DVD TT
CH
DVD TT
CH
VCD 2.0 TR K
CDDA
TR K
PB C
X
X
19.MUTE button
Press to mute and restore the sound.
20.SLOW button
Forward slow playback.
Each time you press the SLOW button, the slow-motion
speed changes in the following sequence:
1/4
1/8
Play
Note
The sound is muted during slow-motion playback.
21.SUBTITLE/MP3 CONV. button
For DVDs, press this button to change the language of
the subtitle.
To turn off the subtitle, press the SUBTITLE button
repeatedly until the .... : [ off is displayed.
For CDs, access the MP3 converting menu.
Notes
• Some DVDs are set to display subtitles automatically,
and you cannot turn them off even if you set the subtitle
function to off.
• During some scenes, the subtitles may not appear
immediately after you select your desired.
• Some DVDs will allow you to make subtitle selections
and turn subtitles on or off only via the disc menu.
22.AUDIO button
For DVDs, press the AUDIO button to toggle between
different audio modes. The selected audio mode will be
displayed on the screen.
For VIDEO CDs, press the AUDIO button repeatedly
during playback to hear a different audio channel (Stereo,
Left, Right or Mono).
Notes
• When you turn on the DVD player or replace a disc,
player returns to the initial default setting.
• If you select a sound track which is not included on
the disc, the DVD player plays a prior soundtrack
programmed on the disc.
• Some discs allow you to change audio selections only
via the disc menu. If this is the case, press the MENU
button and choose the appropriate language from the
selections on the disc menu.
• Press the corresponding number button(s) for the title
(TT) / chapter (CH) / track (TRK) / time, then press
ENTER. Playback starts from the selected section.
23.PLAY button
• Press to start playback.
• The function is the same as the PLAY button on the
front panel.
Notes
• Pressing the CLEAR button resets the numbers. To
clear the display, press the SEARCH (T) button several
times.
• For VCD with PBC on, accessing tracks using number
buttons does not work.
24.STOP button
• Press once to stop playback and the DVD player
memorizes the location where playback is stopped.
• Press twice to clear the last playback position.
• The function is the same as the STOP button on the
front panel.
25.ENTER button
Press to confirm selections on a menu screen.
12
26.DISPLAY button
Press to view the operational status.
CD Information display
e.g.
DVD Information display
e.g.
Track
Title
D
Title
DVD TT
Camera angle
Subtitles
6CH
1/1
ENG
Remaining time of the
current chapter
Chapter
CH
Title
DVD TT
Elapsed time of the
current title
Chapter
CH
Title
DVD TT
Remaining time of the
current title
Chapter
1) Press DISPLAY while a disc is playing, the first banner
shows the track, play mode information and the elapsed
time display of the current track.
2) Press DISPLAY again for the remaining time display of
the current track.
3) Press DISPLAY a third time for the elapsed time display
of the played tracks.
4) Press DISPLAY a fourth time for the remaining time
display of the disc.
5) To turn off the display, press DISPLAY again.
Track
VCD 2.0 TR K
Track
VCD 2.0 TR K
Track
VCD 2.0 TR K
Elapsed time of the
played track
X
Repeat Off
TR K
Remaining time of the
current disc
X
40
27.MENU button
Display the menu of DVD.
28.NAVI button (DVD/VCD)
Press this button to display and access features and
settings.
29.RETURN button
Press to return to previous menu or exit the menu.
For VCD 2.0, PBC must be On in order to return to the
menu when RETURN is pressed.
31. A-B RPT button
Set the beginning and end points of a section to repeat.
VCD Information display
e.g.
VCD 2.0 TR K
X
Repeat Off
TR K
Track
Remaining time of the
current track
30.PBC button
Press to toggle between PBC On and PBC Off.
CH
Track
CDDA
Repeat Off
TR K
Track
CDDA
CH
Audio language
1/3 ENG
CDDA
Elapsed time of the
current track
X
TR K
Track
Elapsed time of the
current chapter
Chapter
DVD TT
CDDA
Repeat Off
Introduction
1) Press DISPLAY while a disc is playing, the first banner
shows the title, chapter information and the elapsed
time display of the current chapter.
2) Press DISPLAY again for Audio language, Subtitles and
Camera angle information.
3) Press DISPLAY a third time for the remaining time
display of the current chapter.
4) Press DISPLAY a fourth time for the elapsed time
display of the current chapter.
5) Press DISPLAY a fifth time for the remaining time
display of the current title.
6) To turn off the display, press DISPLAY again.
Repeat Off
PB C
X
Repeat Off
PB C
Elapsed time of the
played track
X
Repeat Off
PB C
Remaining time of the
current track
X
Repeat Off
PB C
Elapsed time of the
current track
X
Remaining time of the
current disc
40
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment
that includes multiple camera angles.
• You can specify a segment only within the current title
or track (VIDEO CD).
• There may be a slight difference between point A
and the location where playback actually resumes
depending on the disc.
32. ZOOM button
Press to zoom in the current picture.
Notes
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included
on DVDs.
33. HDMI button
Press HDMI to receive a suitable video quality
15
.
The function is the same as the HDMI SELECT on the
front panel.
34. USB button
Select the USB mode during DVD stop.
Note
“PBC” display will change from light green to black when
PBC is set to Off.
13
Connections
Connecting to a TV
Connect the DVD player to your TV.
Connecting to a TV (Using the phono type jacks)
L
VIDEO
HDMI OUT
Normal TV
To audio
input
To wall outlet
To VIDEO
OUT
(yellow)
COAXIAL DIGITAL
ANALOG
R
To 2ch AUDIO OUT
(R: red, L:white)
To video
input
(yellow)
Audio/Video cable (not supplied)
• Make the following setting.
On-screen display
Select:
Page
“Digital out”
“Off”, “PCM”
or “Bitstream”
24
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD player to a Y cable adapter
(not supplied) and then connect to your TV.
• Connect the DVD player directly to your TV. If you connect the DVD player to a VCR, TV/VCR combination or video
selector, the playback picture may be distorted as DVDs are copy protected.
• Analogue audio out will not have sound if DTS playback is selected.
14
About HDMI
HDMI (High Definition Multimedia Interface) supports both
video and audio on a single digital connection for use with
DVD players, DTV, set-top boxes, and other AV devices.
HDMI was developed to provide the technologies of High
Bandwidth Digital Content Protection (HDCP) as well as
Digital Visual Interface (DVI) in one specification. HDCP
is used to protect digital content transmitted and received
by DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced, or
high-definition video plus standard to multi-channel surroundsound audio. HDMI features included uncompressed digital
video, a bandwidth of up to 2.2 gigabytes per second (with
HDTV signals), one connector (instead of several cables and
connectors), and communication between the AV source and
AV devices such as DTVs.
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
L
VIDEO
HDMI OUT
Connections
Connecting to a display (Using a HDMI® cable)
COAXIAL DIGITAL
ANALOG
R
To HDMI
Output
HDMI Cable
Available output signals are below:
• Auto
• 576p/480p (progressive)
• 720p (progressive)
• 1080i (interlaced)
• 1080p (progressive)
(not supplied)
HDMI-compatible display
• Make the following setting.
Switching the video quality (HDMI mode) using
HDMI button on the remote control or HDMI
SELECT button on the front panel.
Press HDMI button on the remote control or HDMI
SELECT button on the front panel to receive a suitable
video quality. The video quality is required to match your
TV having HDMI feature and suitable quality. Please
also check your TV owner’s manual. Press this button
to change the output signals as below. See the HDMI
indicator and select the appropriate output signal.
HDMI indicator
Video output signal
illuminates “ • 1080p ”
1080p (progressive)
Press
illuminates “ • 1080i ”
1080i (interlaced)
Press
illuminates “ • 720p ”
720p (progressive)
Press
illuminates “ • 576p/480p ” 576p/480p (progressive)
Press
illuminates “• 576p/480p,
• 720p, • 1080i, • 1080p”
Auto
Press
576p/480p, 720p, 1080i and 1080p are signals created
with this DVD Player from original 576i/480i signal. The
resolution of the picture may not be increased even if
they are selected.
On-screen display
Select:
Page
“Digital out”
“PCM”
24
Notes
• Refer to the owner’s manual of the connected TV as well.
• If Auto is selected, it follows preference HDMI aspect ratio
of TV.
• When you connect the DVD player to your TV, be sure to
turn off the power and unplug both units from the wall outlet
before making any connections.
• If you have a HDMI (with HDCP) equipped monitor or
display, you can connect it to this player using a HDMI
cable.
• The HDMI connector outputs uncompressed digital video,
as well as almost every kind of digital audio that the player
is compatible with, including DVD-Video, Video CD/Super
VCD, CD, MP3 and DivX®.
• This unit has been designed to be compliant with HDMI
(High Definition Multimedia Interface) depending on the
component you have connected. Using a HDMI connection
may result in unreliable signal transfers.
• Because HDMI is an evolving technology, it is possible that
some devices with an HDMI input may not operate properly
with this DVD player.
• When using HDMI cable, do not connect to other analog
video outputs.
15
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
• For connection to your TV, see “Connecting to a TV” .
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Warning
• When you are connecting (via the COAXIAL DIGITAL
AUDIO OUT jack) an AV decoder that does not have
Dolby Digital, DTS® or MPEG2 decoding function, be
sure to set “Digital out” to “PCM” from the on-screen
displays. Otherwise, high volume sound may damage
your hearing as well as the speakers.
• When playing DTS-encoded discs (DVDs and audio
CDs), excessive noise may be output from the analog
audio output jacks. To avoid possible damage to the
audio system, you should take proper precautions when
the analog audio output jacks of the DVD player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the COAXIAL DIGITAL AUDIO OUT jack
of the DVD player.
Notes
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital
Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL
DIGITAL AUDIO OUT jack of the DVD player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the “DIGITAL (COAXIAL)” input of a Receiver or
Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on,
the speakers may be damaged.
Connecting to an amplifier equipped with a Dolby® Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest
movies, and is now available to reproduce this realistic effect in the home. You can Manufactured under license from
Dolby Laboratories. Dolby and the
enjoy motion picture and live concert DVDs with this dynamic realistic sound by
double-D symbol are trademarks of
connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital
Dolby Laboratories.
decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder,
you will obtain the full benefit of Pro Logic from the same DVD movies that provide • Use DVDs encoded via the Dolby
full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby
Digital recording system.
Surround mark.
• Make the following setting.
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL
type digital
audio input
COAXIAL DIGITAL
To wall
outlet
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
16
L
VIDEO
ANALOG
R
On-screen display
Select:
Page
“Digital out”
“PCM” or
“Bitstream”
24
Connecting to an amplifier equipped with Dolby Surround Pro Logic
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby® Digital decoder.” Refer to that amplifier’s owner’s manual
and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
“Digital out”
“PCM” or
“Bitstream”
24
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
Amplifier equipped with
Dolby Surround Pro Logic
To audio
input
* Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if
you connect two rear speakers.
L
VIDEO
COAXIAL DIGITAL
ANALOG
R
To ANALOG
AUDIO OUT
To wall
outlet
Audio cable (not supplied)
Connecting to an amplifier equipped with a DTS® decoder
DTS®
DTS is a high quality surround technology used in theaters and now available for
home use, on DVDs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVDs or audio CDs.
Amplifier equipped with a
DTS decoder
COAXIAL DIGITAL
To COAXIAL
type digital
audio input
L
VIDEO
To wall
outlet
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
ANALOG
Manufactured under license under
U.S. Patent #: 5,451,942 & other
U.S. and worldwide patents issued
& pending. DTS and the Symbol
are registered trademarks and DTS
Digital Out and the DTS logos are
trademarks of DTS, Inc. Product
includes software. © DTS, Inc. All
Rights Reserved.
R
• Use DVDs or audio CDs encoded via
the DTS recording system.
• Make the following setting.
On-screen display
Select:
Page
“Digital out”
“Bitstream”
24
17
Connections
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting • Make the following setting.
an amplifier and speaker system (right and left front speakers, a center speaker,
On-screen display
Select:
Page
and one or two rear speakers).
Connections
Connecting to Optional Equipment (continued)
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVDs with dynamic realistic sound • Use DVDs encoded via the MPEG2
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2
recording system.
audio processor.
• Make the following setting.
Amplifier equipped with an
MEPG2 audio decoder
COAXIAL DIGITAL
To COAXIAL
type digital
audio input
To wall
outlet
On-screen display
Select:
Page
“Digital out”
“PCM” or
“Bitstream”
24
L
VIDEO
ANALOG
R
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an • Make the following setting.
amplifier equipped with a digital audio input and speaker system (right and left
On-screen display
Select:
Page
front speakers).
“Digital out”
Amplifier equipped with
a digital audio input
To COAXIAL
type digital
audio input
COAXIAL DIGITAL
To wall
outlet
To COAXIAL
DIGITAL
AUDIO OUT
75 Ω coaxial cable (not supplied)
18
L
VIDEO
ANALOG
R
“PCM”
24
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to
the DVD player.
1
Press the ON/STANDBY button.
2
Press OPEN/CLOSE.
The DVD player turns on.
To pause playback (still mode)
The disc tray opens.
Press PAUSE/STEP during playback.
To resume normal playback, press the
PLAY button.
• The sound is muted during still
mode.
Place the disc on the disc tray.
With the playback
side down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out
of the guide, it may damage the disc and cause the
DVD player to malfunction.
• Do not place a disc which is unplayable in this DVD
player.
4
Basic playback
3
To start playback in the stop mode
Press PLAY.
Press OPEN/CLOSE to close the disc tray.
Playback starts.
To stop playback
Press STOP.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Be sure to press the OPEN/CLOSE
button to close the disc tray after you
remove the disc.
To turn the power off
Press ON/STANDBY button to turn the unit off.
If you insert a DVD that contains a top menu, a
to select the
menu may appear. Use / / /
title you want to view, then press ENTER to start
playback.
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the actual
DVD.)
Notes
• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last
stopped.
• Some video CD are recorded with PBC (Playback
Control), a menu with recorded contents may appear
on the TV if you have turned the PBC on. You can make
your selection according to its PBC menu. Press the PBC
button on the remote control to turn PBC on or off anytime
during Video CD playback. When switching from PBC off
to PBC on mode, playback will start from the beginning
of the disc. To turn on the menu display again, press the
RETURN button.
Automatic Power Off function
If the DVD player is stopped, or the screen saver is
engaged for approximately 20 minutes, the DVD player
will automatically turn itself off.
Notes
• Do not move the DVD player during playback. Doing so
may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc
tray. Do not push the disc tray while it is moving. Doing
so may cause the DVD player to malfunction.
• Do not push up on the disc tray or put any objects other
than discs on the disc tray. Doing so may cause the DVD
player to malfunction.
• In many instances, a menu screen will appear after
playback of a movie is completed. Prolonged display
of an on-screen menu may damage your television set,
permanently etching that image onto its screen. To avoid
this, be sure to press the STOP button on your remote
control once the movie is completed.
19
Basic playback
Playing MP3/DivX®/JPEG Files
You can play MP3, DivX® or JPEG files that have been recorded on a CD-R or CD-RW on the DVD player.
Playing MP3/DivX®/JPEG Files
1
Press OPEN/CLOSE to open the disc tray,
place a disc that contains MP3/DivX®/
JPEG Files.
A selection menu
will appear on the
screen.
ENTER
: music icon
2
: picture icon
: video icon
Press / to select the Music, Picture or
Video icon, and then press ENTER.
(For example: selecting the Picture icon)
MP3 Playable files
MP3 disc compatibility with this player is limited as
follows:
• Playable discs:
CD-R (650MB / 74 min. only)
CD-RW may not be compatible.
• Sampling Frequency: 44.1 kHz only
• Bit rate:
32 kbps - 320 kbps (CBR*)
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet
and numerals only, and must
incorporate “MP3” extension.
e.g. “********.MP3”.
• Total number of folders: Less than 100
• Total number of files: Less than 1000
* CBR = Constant Bit Rate
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files). Because this area of technology is still
evolving, Toshiba cannot guarantee that all recordable
discs will produce optimal playback quality. The technical
criteria set forth in this owner’s manual are meant only
as a guide.
Please be advised that you must obtain permission from
the applicable copyright owners to download copyrighted
content, including music files, in any format, including the
MP3 formats, prior to the downloading thereof. Toshiba
has no right to grant and does not grant permission to
download any copyrighted content.
Make sure the disc you are playing contains the
music, picture or video files.
...[PHOTOS]123.JPG
A list of folders in the
disc appears, press
/ button to select
a folder and then
press ENTER.
e.g.
...
C0001
C0002
C0003
C0004
2288X1712
766KB
1
C0005
C0006
2009/12/01
PGUP/DN RETURN
C0007
ENTER
MENU
: selects a file.
: Page up or Page down
MENU : views a thumbnail view.
RETURN : returns to previous menu.
ENTER : plays your selected file.
DivX® Playable files
DivX® disc compatibility with this player is limited as
follows:
• Playable discs:
Notes
• Make sure that a disc you want to play is compatible with
this DVD player.
• Some discs may not permit this operation.
• When the MP3 file is out of the above specifications, the
song may be skipped or muted with counter moving.
• If your DivX® files include the subtitle file supported by
this unit (see 23 ), press SUBTITLE to toggle the available
subtitles or off.
• Some DivX ® Video-On-Demand files may require
registration code of your DVD player, you may get the code
in TV System settings 26 .
• It is recommended to record the same kind of files in a
CD-R or CD-RW.
20
•
•
•
•
•
•
•
•
•
CD-R (650MB / 74 min. only)
CD-RW may not be compatible.
DivX® 3.11, 4.12, 5.0, 5.1
DivX versions:
Audio format:
CBR MP3, VBR MP3, Mono
MP3, DivX® AC3
Enhance video:
GMC, Qpel, Progressive
B-frames
Frame rate:
8 to 25 fps
CD physical format:
Mode 1, Mode 2 X A Form 1
File system:
ISO9660 Level 1, 2 or Joliet
File name:
A file name should be in
alphabet and numerals only, and
must incorporate “DIVX” or “AVI”
extension.
e.g. “ ********.DIVX ”, “ ********.AVI ”
Total number of folders: Less than 100
Total number of files: Less than 1000
®
ABOUT DIVX VIDEO : DivX® is a digital video format
created by DivX, Inc. This is an official DivX Certified
device that plays DivX video. Visit www.divx.com for more
information and software tools to convert your files into
DivX video.
Zooming in an image
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play DivX Video-onDemand (VOD) content. To generate the registration code,
locate the DivX VOD section in the device setup menu. Go
to vod.divx.com with this code to complete the registration
process and learn more about DivX VOD.
Press the / / /
buttons to view a different part
of the image. You may move the image from the centre
position to up, down, left and right direction. When you
reach the edge of the image, the display will not shift
anymore in that direction.
DivX Certified® to play DivX® video, including premium
content.
Rotating an image
Press the ANGLE button repeatedly. The image will rotate
in the clockwise direction as follows:
®
DivX , DivX Certified and associated logos are
registered trademarks of DivX, Inc. and are used under
license.
JPEG files compatibility
Viewing a thumbnail view
JPEG disc compatibility with this DVD player is limited as
follows:
• Playable discs:
CD-R (650MB / 74 min. only)
CD-RW may not be compatible.
• CD physical format: Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet
and numerals only, and must
incorporate “JPG” extension.
e.g.“********.JPG” (Do not name
the file with “JPE” or “JPEG”
extension.)
• Total number of folders: Less than 100
• Total number of files: Less than 1000
Press MENU in the photo list screen
e.g.
Depending on the file size, some files may not display the
entire image.
Some discs may not permit this operation. Especially, the
following conditions of included files will increase the disc’s
disability.
1. Pixels over 4000 x 4000 in height and/or width
2. File size over 16M bytes
3. File format except Exif
Slide Show playback
20
C0001 [784k]
C0002 [704k]
C0003 [684k]
C0004 [584k]
C0005 [804k]
C0006 [484k]
.
1. Press the / / / to select an image, press the
ENTER button to view one image in full-screen.
2. Press SKIP
/
to view other thumbnail screen.
The Slide Show enables you to view picture (files) one
after another automatically.
• Set “JPEG Interval” setting to “5 seconds”, “10 seconds”
or “15 seconds” 24 .
21
Basic playback
®
Press ZOOM repeatedly to toggle through Q1, Q2 and
Q3.
To return to normal playback, press ZOOM until the Q:Off
appears.
Basic playback
Playing USB Device
You can connect the USB flash drives (not included) to the USB jack on the front of DVD player.
You can play the files in MP3, DivX® or JPEG format stored on a USB flash drive by connecting it to this player.
Connecting to USB flash drive
1
2
Plug the USB flash drive to the USB jack on
the front of DVD player.
Press the USB button on the remote control
to select USB mode during DVD stop.
A selection menu will appear on the screen if it
contains music, picture or video files in the USB
device.
USB
ENTER
3
Press / to select the Music, Picture or
Video icon, and then press ENTER.
(please see 20 for details.)
To return to DVD mode
DVD
• Pressing the DVD button on the remote
control to resume DVD playback during
USB device stop.
Notes
• It is recommended to plug the USB flash drive when the
DVD player is off.
• It does not support USB harddisk mass storage device,
multi-card reader and other USB computer peripheral.
• It only supports FAT format (e.g. It does not support
NTFS).
• It only supports USB flash drive (max. 4G bytes).
• The unit can recognise up to 127 folders and 999 files
only.
• It is not possible to play back files whose file size exceeds
1G bytes.
• The connection may not be available depending on the
type of your USB flash drive.
• Do not disconnect the USB flash drive when you are
playing it, it may corrupt the data. You may remove it in
stop mode or DVD mode.
MP3 Converter (converting CD to USB device)
MP3 Converter allows you to convert tracks on CD to USB device. Connect the USB device first before converting.
1
During CD playback, press SUBTITLE/MP3
CONV. button on the remote to activate the
converting menu.
SUBTITLE/MP3 CONV.
MP3 CONVERTER
1’S
ENCODER OPTIONS
OPTIONS
1X
SPEED
BITRATE
TRACKS
START
128KBPS
FILE OPTIONS
CREATE ID3 TAG
CREATE PLAYLIST
QUIT
2
Select one of the menu items using the
buttons.
/
OPTIONS
Press the
button and use the
/
buttons to select the
setting option (SPEED, BITRATE, CREATE ID3 TAG or CREATE
PLAYLIST), then press the ENTER button to change the
setting.
Speed
High speed converting mode can save time when converting from
CDs. Select 1x(normal speed) or 2x(double speed) by pressing
the ENTER button.
Bitrate
Select 128kbps, 160kbps,192kbps, 256kbps or 320kbps by
pressing the ENTER button.
22
Create ID3 TAG/Create Playlist
It allows you to create ID3 TAG and playlist for your converted
files. The default ( ) is for creating them and press the ENTER
button to shift the setting.
• Only CDDA with CD Text supports creating ID3 TAG.
• All converted files will be saved to the folder named as the
album of the CD TEXT of the CD (e.g. “#1’S”) with file name
as the track number (e.g. if it is track02, it will generate a
track02.mp3).
• After creating ID3 TAG, the artist name and the song name
also will be converted to the MP3 file, and they will appear
during playback.
• After creating Playlist, you can play all tracks in playlist folder
you converted if your MP3 player has the playlist function.
TRACKS
Press the button and use the / buttons to select the tracks
you want to convert, then press the ENTER button.
START
Press the ENTER button to start converting.
QUIT
Press the ENTER button to quit the converting menu.
Notes
• MP3 Converter function only supports CDDA discs.
• During 2x converting, the audio output is muted.
• If your discs have the copyright protection, it cannot convert
to USB device.
Customizing the Function Settings
You can change the default settings to customize performance to your preference.
Using the Language setup menu
1. Press SETUP during stop, the system setup menu
appears.
2. Press
/
button to select the setting item: Language,
Subtitle, Audio, DVD Menu or DivX Subtitle.
3. Press button, then use / button to select the setting
choice on the right.
4. Press ENTER button.
5. Press SETUP button to exit the menu.
DivX® Subtitle
If your DivX® files include a subtitle file, then you may select
a supported DivX® subtitle language:
Standard (English)
Russian
Czech
Hebrew
Modern Greek
Turkish
Notes
• If your DivX® files do not include the subtitle file, you cannot
use this selection.
• Supported subtitle file formats:
.srt, .sub, .txt, .smi, .ssa.
Language
Language
Subtitle
Audio
DVD Menu
DivX Subtitle
Using the Video setup menu
Language
To select a preferred language for on-screen displays.
English:
To view on-screen displays in English.
Français:
To view on-screen displays in French.
:
To view on-screen displays in Arabic.
Ðóññêèé:
To view on-screen displays in Russian.
Bahasa Indonesia: To view on-screen displays in Indonesian.
:
To view on-screen displays in Persian.
Subtitle/Audio/DVD Menu
Video
Aspect Ratio
HDMI Res.
JPEG Interval
DVD
These menus contain various language options for Subtitle,
Audio and DVD Menu which may be recorded on the DVD.
Notes
• Some DVDs may be set to display subtitles in a different
language other than your selection. A prior subtitle
language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections only
via the disc menu. If this is the case, press the MENU
button and choose the appropriate subtitle language from
the selection on the disc menu.
• Some DVDs may not be played in a different language
that you selected. A prior language may be programmed
on the disc.
• Some DVDs may not include your pre-selected language.
In this case, the DVD player automatically displays
disc menus consistent with the disc’s initial language
setting.
Aspect Ratio
DVD
Depending on the format of the DVD disc, you can choose the
picture format (aspect ratio) best suited to the format of your
TV screen.
4:3 LB : Select when a standard 4:3 TV
is connected. When wide-screen
video is played in this mode on a
conventional screen, black bands
appear at the top and bottom of
the screen.
4:3 PS : Select when a standard 4:3 TV
is connected. Displays pictures
cropped to fill your TV screen.
Either or both sides of the picture
are cut off.
16 : 9 : Select when a 16:9 TV is connected.
For playing wide-screen videos on
a wide-screen TV.
23
Function setup
1. Press SETUP during stop.
2. Press button to select Video.
3. Press / button to select the setting item: Aspect Ratio,
HDMI Res. or JPEG Interval.
4. Press button, then use / button to select the setting
choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
Function setup
Customizing the Function Settings (continued)
Notes
• The displayable picture size is preset on the DVD.
Therefore, the playback picture of some DVDs may not
conform to the picture size you select.
• When you play DVDs recorded in the 4:3 picture size only,
and you own a 16:9 TV set, Video output picture will be
16:9 only when you select the TV picture setting on the
TV.
• If you select “16:9” and you own a 4:3 TV set, the DVD
playback picture will be horizontally distorted during
playback. Images will appear to be horizontally compressed.
Always be sure that your TV shape conforms to the actual
TV in use.
Using the Audio setup menu
1. Press SETUP during stop.
2. Press button to select Audio.
3. Press / button to select the setting item: Digital out or
Night Mode.
4. Press button, then use / button to select the setting
choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
Audio
HDMI Res. (Resolution)
Digital out
Night Mode
You can set the HDMI Res. (Resolution) to be Auto,
480p/576p, 720p, 1080i or 1080p, according to the
connected TV.
Note
Select the HDMI resolution according to the performance
of the connected TV.
Digital out
JPEG Interval
To set the JPEG Interval for slide show playback. Select
“Off” to disable the slide show feature.
5 seconds: Plays back images in the form of a slide show
at 5 seconds interval.
10 seconds: Plays back images in the form of a slide show
at 10 seconds interval.
15 seconds: Plays back images in the form of a slide show
at 15 seconds interval.
Selects the output sound format corresponding to your
system connection.
Off:
To disable Digital out.
Bitstream: Disc audio raw data will be output. Select
“Bitstream” if your amplifier supports “DTS”.
PCM:
Select when connected to a Multi-channel digital
stereo amplifier. The DVD player outputs sound
in the PCM stereo format when you play a DVD
recorded on the Dolby Digital, MPEG1 or MPEG2
recording system.
Night Mode
DVD
Night mode is equivalent to Dynamic Range Compress.
When it is On, it reduces the variations between loud and
soft sounds in audio output. You can still hear softer sounds
and dialogue even in very low volume.
Note
Night mode is Dynamic Range Control (DRC) option for
analogue audio output.
24
Using the Parental Lock setup menu
1. Press SETUP during stop.
2. Press button to select Parental Lock.
3. Press / button to select the setting option: Password
or Parental Lock.
Parental Lock
Password
Parental Lock
The parental lock levels are equivalent to the following
ratings.
Level 1 : Kid Safe
Level 2 : G
Level 3 : PG
Level 4 : PG-13
Level 5 : PG-R
Level 6 : R
Level 7 : NC-17
Level 8 : Adult
• DVDs may or may not respond to the parental lock settings.
This is not a defect in the DVD player. Make sure this
function works with your DVDs.
• Parental lock level cannot be changed when the Parental
lock is active.
DVD
Press / button to select the Password option, then press
button. Enter your 4-digit security code and then press the
ENTER button.
If you forget the password, you can erase your current
password by pressing number button 8 on the remote
control four times, then press ENTER button to confirm
the setting. (PASSWORD: 8888)
The Parental lock
is active.
Parental Lock
The Parental lock is
NOT active.
Using the TV System setup menu
1. Press SETUP during stop.
2. Press button to select TV System.
3. Press / button to select the setting item: Initialization,
View DivX(R) VOD, Screen Saver, HDMI CEC or TV
System.
4. Press button, then use / button to select the setting
choice on the right.
5. Press ENTER button.
6. Press SETUP button to exit the menu.
DVD
DVDs equipped with the password function are rated
according to their content. The contents allowed by a
parental lock level and the way a DVD can be controlled
may vary from disc to disc.
For example, if the disc allowed, you could edit out violent
scenes unsuitable for children and replace them with more
suitable scenes, or you could lock out playback of the disc
altogether.
1) Press / button to select the Parental Lock option,
then press button.
2) Press / button to select parental lock level and then
press the ENTER button.
3) Press / button to select the Password option, then
press button. Enter your 4-digit security code and then
press the ENTER button.
You cannot play DVD discs rated higher than the level
you selected unless you cancel the parental lock
function and enter the 4-digit security code. Then
press ENTER to confirm the password.
TV System
Initialization
View DivX(R) VOD
Screen Saver
HDMI CEC
TV System
Initialization
This option allows you to return the unit’s setting to the factory
default. Any changes you have made to the unit’s settings will
be reverted back to the original setting except your password
and parental lock level.
Note
When you reset the DVD player to the factory default, the
DVD player will take 3-5 seconds to reset.
25
Function setup
Password
If you forget your password at this moment, you cannot
use the super password (8888). You need to go to the
Parental Lock setup menu to reset and input a new
password.
Function setup
Customizing the Function Settings (continued)
View DivX(R) VOD
HDMI CEC
DivX® Deregistration
DivX® deregistration code allows you to deregister your
DVD player using the DivX® VOD service from the internet,
please get the deregistration code as follow:
DEREGISTRATION CODE:
DEREGISTER AT HTTP://VOD.DIVX.COM
CONTINUE WITH REGISTRATION?
OK
CANCEL
For more information, please visit http://vod.divx.com
If you want to continue with registration, please select “OK”
then press “ENTER” on the remote control.
DivX® Registration
DivX® registration code allows you to rent and purchase
movies using the DivX® VOD service from the internet,
please get the registration code of your DVD player as
follow:
YOU MUST REGISTER
YOUR DEVICE TO PLAY
DIVX PROTECTED VIDEOS.
REGISTRATION CODE:
REGISTER AT HTTP://VOD.DIVX.COM
OK
Registration service at http://vod.divx.com
Follow the instructions and download the movie from your
computer onto a CD-R/RW or DVD±R/RW for playback on
this DVD player.
Note
This registration code is for DivX® Video-On-Demand only.
Do not apply this code for other applications or websites.
Screen Saver
To turn on or off the screen saver (screen protection to
prevent image burn).
Note
When you leave the unit in DVD stop mode for approximately
2 minutes, the screen saver of the DVD player automatically
appears if you set the Screen Saver to On mode. To turn
off the screen saver, press the PLAY button.
26
You can control this DVD unit from TV’s remote which is
connected via HDMI cable.
Functions available for the HDMI-CEC
• One touch play
When the operations with following buttons of this unit’s
remote control are performed, the TV will automatically
switch to appropriate input channel.
Button for one touch play: [PLAY] (make sure a disc is
inserted.)
• System information
Get & Set Menu Language:
This unit recognizes the OSD languages set for the TV and
automatically set the same language as the player menu
language (OSD menu language) for this unit.
Power off:
When you turn the TV off, this unit will automatically turn
off.
Receiving operational signal from TV’s Remote:
You can operate this unit with TV’s remote control. Check
your TV owner’s manual for details.
Notes
• This function may not work properly depending on the TV
you are connecting.
• Other components must be compatible with HDMI-CEC in
order to use this function.
TV System
NTSC: Select if your TV system is NTSC.
PAL: Select if your TV system is PAL.
Auto: The DVD player automatically identifies PAL or NTSC
video system of a disc. Connect a multisystem TV
(PAL / NTSC compatible) to view a picture. A playback
picture may be distorted when detected a signal
change between PAL and NTSC on the disc. For
the case of Progressive mode, your multisystem TV
must be able to support 525p and 625p.
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Cause
Correction
No power.
Symptom
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
The DVD player turned off
by itself.
• The automatic power off function turned
the unit off.
• Press the PLAY button.
No picture.
• The TV is not set to receive DVD signal • Select the appropriate video input mode on
output.
the TV so the picture from the DVD player
appears on the TV screen.
19
• The video/HDMI cable is not connected • Connect the video/HDMI cable securely into
securely.
the appropriate jacks.
14-15
• Wrong connection.
14-15
No sound.
• Check the connection.
Page
14-15
19
• The equipment connected with the audio • Select the correct input mode of the audio
cable is not set to receive DVD signal
receiver so you can listen to the sound from the
output.
DVD player.
19
• The audio cable is not connected • Connect the audio cable securely into the
securely.
appropriate jacks.
14-18
• Turn on the equipment connected with the
audio cable.
19
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
24
The playback picture has • The disc is dirty.
occasional distortion.
• It is in fast forward or fast reverse
playback.
• Remove the disc and clean it.
5
• Sometimes a small amount of picture distortion
may appear. This is not a malfunction.
-
Brightness is unstable or • The effect of copy protection.
noises are present in the
playback pictures.
• Connect the DVD player directly to the TV.
Avoid connecting the DVD player to a VCR
or TV/VCR combination.
14
• No disc is inserted.
• Insert a disc.
19
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type
and colour system.)
6
• The disc is placed upside down.
• Place the disc with the playback side down.
19
• The disc is not placed within the guide.
• Place the disc correctly inside the guide on
the disc tray.
19
• The disc is dirty.
• Clean the disc.
• The parental lock function is set.
• Cancel the parental lock function or change
the parental lock level.
The DVD player does not
start playback.
Others
• The audio receiver or TV is turned off.
5
25
Playback does not follow
the course of the disc’s
program.
• It is in the mode of repeat playback, memory • These operations may prevent a proper
playback, etc.
progress of the contents.
-
Buttons do not work.
• Power supply fluctuations or other • Press and hold the ON/STANDBY button on
abnormalities such as static electricity may
the front panel for more than about 3 seconds.
interrupt correct operations.
The DVD player turns off. Press the button
again to turn it on. If the buttons still do not
work, disconnect the power plug and insert it
into the wall outlet again.
-
The remote control does
not work properly.
• The remote control is not pointed at the
remote sensor of the DVD player.
• Point the remote control at the remote sensor
of the DVD player.
9
• The remote control is too far from the DVD
player.
• Operate the remote control within about 7 m.
9
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
9
27
Others
Specifications
DVD player / outputs / supplied accessories
DVD Player
Power supply
100V - 240 V AC, 50/60 Hz
Power consumption
9 W (standby: less than 1.0W)
Mass
1.28 kg
External dimensions
430 x 42 x 209 mm (W/H/D)
Signal system
PAL/3.58 NTSC
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio
More than 93 dB
Audio dynamic range
More than 80 dB
Harmonic distortion
Less than 0.05 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Outputs
Video output
1.0 V (p-p), 75 Ω, pin jack x 1
Audio output (COAXIAL DIGITAL)
0.5V (p-p), 75 Ω, pin jack x 1
Audio output (ANALOG)
2.0 V (rms), 680 Ω, pin jacks (L, R) x 1
HDMI output
19 pin
Supplied Accessories
Remote control (SE-R0384) ..................................1
Batteries (R03/AAA) ...............................................2
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
811-501091W110
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement