FCC Information Safety Information

FCC Information Safety Information
EN
Safety Information
FCC Information
Technical Specification
FCC Information
Product: Clock Radio with CD player
Brand: RCA
Model: RP5610
Electrical Consumption
Power Supply: 120V~60Hz
Power Consumption: 11 Watts
IMPORTER
Comercializadora Thomson de México, S.A. de C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
For Your Records
In the event that service should be required, you may need the model number. In
the space below, record the date and place of purchase:
Date of Purchase:
Place of Purchase:
Service Information
This product should be serviced only by those specially trained in appropriate
servicing techniques. For instructions on how to obtain service, refer to the warranty
included in this Guide.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson
Inc. could void the user’s authority to operate this
product.
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:
• Re-orient the receiving antenna (that is, the
antenna for the radio or television that is
“receiving” the interference).
• Move the unit away from the equipment that is
receiving interference.
• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference
are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problems.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
For Your Safety
The AC power plug is polarized
(one blade is wider than the
other) and only fits into AC
power outlets one way. If the
plug will not go into the outlet
completely, turn the plug over
and try to insert it the other
way. If it still does not fit, contact a qualified
electrician to change the outlet, or use a different
one. Do not attempt to bypass this safety feature.
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
Main plug is used as the disconnect device,it shall
remain operable and should not be obstructed
during intended used.To be completely
disconnected the apparatus from supply
mains,the main plug of the apparatus shall be
disconnected from the mains socket outlet
completely.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme de NMB-003 du Canada.
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY WITH
SAME TYPE FUSE.
1
RP5610_EN(US)
2-3
4/10/06, 2:14 PM
EN
Before you begin
EN
This clock radio is equipped with a memory
holding system that can be powered with
9V battery (not included). The power
failure protection circuit will not operate
unless battery is installed.
When normal household power is
interrupted, or AC cord is unplugged, the
battery will power the clock radio to keep
track of time and alarm settings
programmed into the memory. When the
battery backup functions, the digital
display will not light, however, the
function of alarm still occurs during the
power interruption if remaining battery
power is adequate. Normal operation will
resume after AC power is restored so you
will not have to reset the time or the
alarm.
Operating the Clock
Power Failure Indicator
EN
When the AC power is interrupted
(disconnected) for a short period of time,
both time and alarm settings will change
(unless optional battery is installed). After
AC power is restored (reconnected), the
Digital Display will blink to indicate that
power was interrupted and you should
re-adjust the time and alarm settings.
Setting time:
1. Press the SET button until is displayed .
or FWD
to set the time.
2. Press REV
3. AM or PM icon will show beside the
time.
Tip:
No icon will be flashing if all
selectors are set, if you see any
icon flashing on display, press
the SET button repeatedly to confirm
everything is set correctly.
Install battery as below:
1. Remove battery compartment door
(located at the bottom of the radio) by
applying thumb pressure to area
indicated on battery door and then lift
the door out and off the cabinet.
2. Connect a 9V battery to the connector
plug.
3. Insert battery in the compartment and
replace the compartment door.
The descriptions and characteristics in this owner’s manual are for the purpose of general
reference only and not as a guarantee. In order to provide you with the highest quality
product, we may make changes or modifications without prior notice. The English version serves
as the final reference on all product and operational details should any discrepancies arise in
other languages.
2
RP5610_EN(US)
3
4-5
4/10/06, 2:14 PM
Operating the Radio
Operating the CD player
EN
EN
FM
AM
TUNING
AM/FM
Tuning the Stations
Antennas
1. Press ON to turn on the radio.
2. Slide the FM/AM switch to the desired
broadcast band.
3. Turn the TUNING knob to select a
station.
4. Press OFF to turn off the radio.
AM Antenna - A built-in ferrite rod
antenna eliminates the need for an outside antenna for AM reception. Rotating
the unit slightly may improve the reception of distant AM stations.
Built-In AFC
The Built In Automatic Frequency Control
(AFC) works only on FM. It helps reducing
drift on FM reception and keeping the
radio locked in on the FM station to which
it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning can
be well-tuned on two or three nearby
points on the dial. Always tune carefully
at the loudest and clearest point.
Listening to compact disc
Selecting play mode
1. Lift to open the CD compartment door.
2. Insert a disc and close the door.
.
3. Press PLAY/PAUSE
4. Adjust volume to your desired level.
5. Press REV
or FWD
to skip backward and forward.
6. Press STOP to stop CD playback.
1. Start CD playback.
2. During playback, press CD MODE to
toggle between different play modes.
Note:
FM antenna - The power cord acts as your
FM antenna. It picks up moderate to
strong stations and eliminates the need for
an external antenna in most strong signal
areas. Be sure the power cord is stretched
to its full length. Do not coil or bunch the
cord together. Changing position of the
power cord may improve reception.
Tip:
You may try to move the power
cord in order to improve the reception.
When there is no disc in the
CD compartment, “nd” will
show on display.
Listening to auxiliary source
1. Connect the external auxiliary source
(e.g. mp3 player) to AUX IN jack on the
left of the unit with an audio cable.
2. Press ON twice to select auxililary input
mode with AUX shows on the display.
3. Adjust volume by rotating the volume
control knob. Control other playback operations on the auxiliary unit.
4
RP5610_EN(US)
REPEAT ONE - repeat the current track.
REPEAT ALL
- repeat the whole disc.
SHUFFLE
- play tracks randomly.
- play random
SHUFFLE REPEAT
tracks repeatedly.
5
6-7
4/10/06, 2:14 PM
Operating the Alarm
Operating the Clock Radio
Sleep Mode
EN
In sleep mode, the radio or CD will turn
off automatically. Simply:
Setting the WAKE Time
Waking by Selected Source
Your digital clock operates on a 12-hour
standard mechanism.
You may be woken up by WAKE
or CD .
1. Press the SET button until WAKE 1 /
WAKE 2 icon is blinking.
2. Press REV
or FWD
to set the wake
time. The time decrements or increments
will follow by a faster rate when you press
or FWD
.
and hold either REV
3. After the WAKE time is set, press SET
repeatedly until no icon is blinking.
1. Select an AM or FM station.
2. Set wake time (see above directions).
3. Press WAKE 1 or WAKE 2 to select waking up by WAKE , RADIO
or CD .
Corresponding indicator will be shown
next to the selected setting.
4. Adjust the volume by turning VOL.
Tip:
The unit equips with GRADU-WAKE feature, the alarm
tone volume will increase
gradually to its maximum in
about 30 to 45 seconds.
Tip:
If you set the SLEEP
function with low volume level
before going to bed, we
mode
advise using WAKE
to wake you up since its volume will
automatically increase.
, RADIO
1. Listen to CD or radio.
2. While holding SLEEP, press REV
or
FWD
to set the sleep time. The time
range is from 1 minute to 2 hours.
3. Release SLEEP and the current time will
be shown again. The radio or CD will turn
off when the preset time elapses. If you
decide to turn off the radio or CD sooner,
press SNOOZE or OFF.
4. When SLEEP is activated again, the sleep
time will be the same as the one you have
set before.
5. Press SLEEP to read the remaining sleep
time.
Press NAP or follow “Turning off Alarm”.
1. Press and hold NAP to cancel the nap
setting.
2. Only alarm sound can be selected.
3. Nap alarm is equipped with GRAD-UWAKE feature.
Turning off Alarm
Silence the alarm momentarily
Press SNOOZE. The alarm will sound again
when the snooze period is over. (See
“Snooze Alarm Operation”).
Stop the alarm
Press OFF. The alarm will sound on the
following day at the same time.
Nap Mode
Disable the alarm permanently
You can select your CD wake track by the
following procedures.
This function wakes you up after a short
period of time. Simply:
1. Make sure you have inserted a CD.
2. While holding WAKE UP CD TRACK,
or FWD
to select your
press REV
desired CD wake up track.
1. Press NAP and release. The
indicator will flash. During this period, adjust
or FWD .
NAP time by pressing REV
The range is from 10 minutes to 2 hours.
2. The clock will be shown after 5 seconds
if no button is pressed. The
indicator
will lit up.
3. Press NAP once to show time left.
1. Press CANCEL.
2. The WAKE indicator will be flashing.
3. Press WAKE 1 or WAKE 2 within 3 seconds to deactivate the corresponding
alarm function permanently.
Note:
When you turn off the alarm by
pressing OFF
OFF, the alarm will
turn on at the same time on the
following day.
Tip:
You can activate the previously
set alarm time by pressing
WAKE 1 or WAKE 2
2.
7
6
RP5610_EN(US)
Stop the Nap alarm
8-9
4/10/06, 2:14 PM
EN
Operating the Clock Radio
U.S. Limited Warranty
EN
COLOR
SELECT
BRIGHTNESS
switch
Snooze Alarm Operation
Brightness control
This operation allows extra sleep time
after the alarm is on. The alarm will turn
off by pressing SNOOZE until the snooze
period is over. Snooze function can be
used repeatedly up to 2 hours. After this,
the alarm will turn off until the next alarm
conditions are met. Set the “quiet” period
as follow:
You can adjust the backlight by adjusting
the BRIGHTNESS switch at the back of
the unit, there are two modes you may
select from:
1. Press and hold SNOOZE.
or FWD
to set the
2. Press REV
“quiet” period (the default time is 9 minutes) from 1 minute to 30 minutes. Release the button, then the “quiet” period
is set.
Seconds Time Display
The unit may display in seconds.
or FWD
to
1. Press and hold REV
show seconds display.
2. Release REV
or FWD
to return
to the hour and minute display.
HI — Stronger Backlight.
LO — Weaker Backlight.
Backlight Color Select
You can choose among 4 different backlight colors - green, blue, amber and
white.
1. Before a specific color is set, the backlight colors will keep changing.
2. Press COLOR SELECT at the back of the
unit to toggle among different backlight colors.
3. If the AC power and backup battery
are removed, the 4 backlight colors will
start changing again once the AC
power is resumed.
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year from date of purchase.
The warranty period for rental units begins with
the first rental or 45 days from date of shipment
to the rental firm, whichever comes first.
What we will do:
• Provide you with a new, or at our option, a
refurbished unit. The exchange unit is under
warranty for the remainder of the original
product’s warranty period.
• Proof of purchase in the form of a bill of sale or
receipted invoice which is evidence that the
product is within the warranty period must be
presented to obtain warranty service. For rental
firms, proof of first rental is also required.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc.,
which were originally provided with the product.
We recommend using the original carton and
packing materials.
• Include evidence of purchase date such as the
bill of sale. Also print your name and address and
a description of the defect. Send via standard UPS
or its equivalent to:
Thomson Inc.,
Product Exchange Center
11721 B Alameda Avenue,
Socorro, Texas 79927
• Insure your shipment for of loss or damage.
Thomson accepts no liability in case of damage or
loss en route to Thomson.
• Pay any charges billed to you by the Exchange
Center for service not covered by the warranty.
• A new or refurbished unit will be shipped to
you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual
provides information regarding operating
Instructions and user controls. For additional
information, ask your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or
incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to
lightning damage.
8
RP5610_EN(US)
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY
WARRANTY APPLICABLE TO THIS PRODUCT.
ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR
WRITTEN INFORMATION GIVEN BY THOMSON
INC., ITS AGENTS OR EMPLOYEES SHALL
CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. THOMSON INC.
SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING
OUT OF ANY BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. THIS
DISCLAIMER OF WARRANTIES AND LIMITED
WARRANTY ARE GOVERNED BY THE LAWS OF
THE STATE OF INDIANA. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW,
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor
limitation of incidental or consequential damages,
or limitations on how long an implied warranty
lasts, so the above limitations or exclusions may
not apply to you.
• This warranty gives you specific legal rights, and
you also may have other rights that vary from
state to state.
If you purchased your product outside the
USA:
This warranty does not apply. Contact your dealer
for warranty information.
9
10-11
4/10/06, 2:14 PM
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement