Feed L302 Feed L304
GB
Origo™ M08, Origo™ M09
Feed L302
Feed L304
Instruction manual
0459 508 101 GB 110203
Valid for serial no. 620-xxx-xxxx
1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
5
3.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
5.1 Lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6.1
6.2
6.3
6.4
6.5
6.6
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanation of function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing feed roller Feed L302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing feed roller Feed L304 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
10
11
11
12
12
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
7.1 Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
8 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
14
16
17
21
Rights reserved to alter specifications without notice.
TOCe
-2-
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE-695 81 Laxå, Sweden, declares that Wire feed unit Feed
L302/Feed L304 from serial number 620 are constructed and tested in compliance with the standard
EN 60974-5 and EN 60974-10 (Class A) in accordance with the requirements of directive
(2006/95/EC) and (2004/108/EEC).
-------------------------------------------------------------------------------------------------------------Laxå 2007-03-14
Kent Eimbrodt
Global Director
Equipment and Automation
2
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves. Note! Do not use safety gloves when replacing wire.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
-3bm38d1ea
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING
Do not use the power source for thawing frozen pipes.
CAUTION
This product is solely intended for arc welding.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION
Read and understand the instruction manual before
installing or operating.
-4bm38d1ea
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
3
INTRODUCTION
The Feed L302 with control panel M08 and Feed L304 with control panel M09 wire
feed units are intended for MIG/MAG welding with the Mig L405 power source.
They come in different variants, see page 16.
The feed units can be used together with wire on ESAB's MarathonPact, or on wire
bobbin Ø 300 mm.
They can be installed either at the power source, suspended above the workplace,
on a support arm or on the floor with or without wheel set.
ESAB's accessories for the product can be found on page 21.
3.1
Equipment
The wire feed units are supplied with an instruction manual and stickers.
4
TECHNICAL DATA
Feed L302
Feed L304
Power supply
42 V 50-60 Hz
42 V 50-60 Hz
Power requirement
150 VA
150 VA
Motor current Imax
3.5 A
3.5 A
Settings data
Wire feed speed
Burnback time
Spot welding time
1.5-22.0 m/min
0-0.7 s
-
1.5-22.0 m/min
0-0.7 s
0.2-5 s
Gun connection
EURO
EURO
Max. diameter wire bobbin
300 mm
300 mm
Wire dimension
Fe
Ss
Al
Cored wire
0.6-1.2 mm
0.6-1.2 mm
1.0-1.2 mm
0.8-1.2 mm
0.6-1.6 mm
0.6-1.2 mm
1.0-1.6 mm
0.8-1.6 mm
Weight
12.6 kg
13.2 kg
Dimensions (l x b x h)
569 x 259 x 355 mm
569 x 259 x 355 mm
Operating temperature
-10 to +40° C
-10 to +40° C
Shielding gas
max pressure
Gases for MIG/MAG welding
5 bar
Gases for MIG/MAG welding
5 bar
-5bm38d1ea
GB
Feed L302
Feed L304
Coolant
max pressure
-
50% water / 50% glycol
5 bar
Maximum permissible load at
60% duty cycle
100% duty cycle
365 A
280 A
365 A
280 A
Enclosure class
basic version
with sealed bobbin holder*
with MarathonPact
IP2X
IP23
IP23
IP2X
IP23
IP23
* Accessories, see page 21.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Apparatus marked IP2X are intended for indoor use.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
5
INSTALLATION
The installation must be executed by a professional.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
WARNING
When welding in an environment with increased electrical danger, only power
sources intended for this environment may be used. These power sources are
marked with the symbol
-6bm38d1ea
GB
5.1
Lifting instructions
Order number for lifting eyelet can be found on page 21.
Note! If another mounting device is used, this should be insulated from the wire feed
unit.
6
OPERATION
AH 0935
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
-7bm38d1ea
GB
WARNING
Assure that the side panels are closed during operation.
WARNING
To prevent the reel from sliding off the hub: Lock the
reel in place by turning the red knob as shown on the
warning label attached next to the hub.
WARNING
Rotating parts can cause injury, take great care.
WARNING
There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm.
Secure the equipment, especially if used on an uneven or sloping surface.
NOTE: When moving the equipment use intended handle. Never pull on the gun.
6.1
Connections and control devices
Connecting control cable
When connecting the control cable, it is
important to secure the cable with the
load-removing grommet.
Ensure that the cover is properly screwed
into place.
-8bm38d1ea
GB
Feed L302
1
Knob for setting wire feed speed
4
Connection for welding gun
2
Knob for setting burnback time
5
Connection for welding current from power
source, (OKC)
3
Switch for 2-stroke / 4-stroke
6
Connection for shielding gas
7
Connection for control cable from power
source
Feed L304
1
Knob for setting wire feed
speed
7
Connection RED for cooling water from
welding gun
2
Switch for activation of 2/4 stroke, spot
welding, cold wire feed or gas purging
8
Connection BLUE, for cooling water to
welding gun
3
Knob for setting spot welding time
9
Connection for welding current from power
source, (OKC)
4
Knob for setting burnback time
10
Connection for shielding gas
5
Switch for creep start OFF / ON
11
Connection for control cable from power
source
6
Connection for welding gun
NOTE! Cooling water connections only available on certain models.
10
-9bm38d1ea
GB
6.2
Explanation of function
Wire feed speed
This sets the required feed speed of the filler wire in m/minute.
2 stroke
With 2-stroke, the gas flow starts followed by the wire feed when the trigger switch is
pressed in. The welding process is concluded when the trigger switch is released,
the wire feed stops and the gas stops flowing.
4 stroke
With 4 stroke, the gas flow starts when the trigger switch is pressed in and the wire
feed starts when it is released. The welding process continues until the switch is
pressed in again, the wire feed stops and when the switch is released the gas stops
flowing.
Spot welding
Spot welding is used when you want to weld on short, repeated occasions with a
pre-set time.
When the trigger switch is pressed in, the gas flow starts for a period of time
governed by the printed circuit board. After this the welding process starts for the set
time. When the welding process is complete, the gas flow stops.
Cold wire feed
Cold wire feed is used to feed wire without welding voltage and gas flow.
Activation of cold wire feed: press in the trigger switch and the wire feed starts.
Gas purging
Gas purging is used to measure that gas flow or to flush the gas hoses to clean them
of any air and moisture before commencing welding. Gas purging is carried out with
the voltage and wire feed switched off.
Activation of gas purging: press in the trigger switch and gas purging starts.
Burnback time
Burnback time is a delay between the time when the wire brakes until the time when
the power source switches off the welding voltage. Too short burnback time results
in a long wire stickout after completion of welding, with a risk of the wire being
caught in the weld pool. Too long a burnback time results in a shorter stickout, with
increased risk of the arc striking back to the contact tip.
Creep start
Creep start means that the wire is fed at 50% lower speed until it comes into
electrical contact with the workpiece, at which point the speed increases to the set
speed.
- 10 bm38d1ea
GB
6.3
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder's pressure rollers. It is important that the
pressure is not too great.
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
6.4
Replacing and inserting wire
WARNING
Risk of crushing! Do not use safety gloves when replacing wire, feed rollers
and wire bobbins.
S
Open the side panel.
S
Disconnect the pressure sensor by folding it backwards, the pressure arm is
folded up.
S
Straighten out 10-20 cm of the new wire. File away burrs and sharp edges from
the end of the wire before inserting it into the wire feed unit.
S
Make sure that the wire goes properly into the feed roller's track and into the
outflow nozzle or wire guide.
S
Fold down the pressure arm and secure it to the pressure sensor.
S
Close the side pannel.
- 11 bm38d1ea
GB
6.5
Changing feed roller Feed L302
S
S
Open the side panel.
Disconnect the pressure sensor (1) by folding it
backwards.
S Disconnect and remove the Allen screw (2) and the
washer.
S Pull out the feed roller (3).
During installation, repeat the above in the reverse
order.
Choice of track in the feed roller
Turn the feed roller with the dimensioning mark for the
required track towards you.
6.6
Changing feed roller Feed L304
S
S
Open the side panel.
Disconnect the pressure sensor (1) by folding it
backwards.
S Disconnect the feed rollers (2) by unscrewing the
nuts (3) and pulling out the rollers.
During installation, repeat the above in the reverse
order.
Choice of track in the feed roller
Turn the feed roller with the dimensioning mark for the
required track towards you.
7
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any faults.
7.1
Inspection and cleaning
Wire feed unit
Check regularly that the wire feed unit is not clogged with dirt.
S
Cleaning and replacement of the wire feed unit mechanism's worn parts should
take place at regular intervals in order to achieve trouble-free wire feed. Note
that if pre-tensioning is set too hard, this can result in abnormal wear on the
pressure roller, feed roller and wire guide.
- 12 bm38d1ea
GB
The brake hub
The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.
S
Adjusting the braking torque:
S
Turn the red handle to the locked position.
S
Insert a screwdriver into the springs in the hub.
Turn the springs clockwise to reduce the braking torque
Turn the springs counterclockwise to increase the braking torque. NB: Turn
both springs through the same amount.
Welding gun
S
Cleaning and replacement of the welding gun's wear parts should take place at
regular intervals in order to achieve trouble-free wire feed. Blow the wire guide
clean regularly and clean the contact tip.
8
ORDERING SPARE PARTS
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Feed L302 / Feed L304 is designed and tested in accordance with the international and
European standards IEC/EN 60974-5 and IEC/EN 60974-10 . It is the obligation of the
service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 13 bm38d1ea
Diagram
Feed L302
- 14 bm38e11a
Edition 110203
Feed L304
- 15 bm38e11a
Edition 110203
Feed L302, Feed L304
Ordering number
Ordering no.
Denomination
Type
0459 495 782 Wire feed unit
Origot Feed L302, M08
0459 495 882 Wire feed unit
Origot Feed L304, M09
0459 495 892 Wire feed unit
Origot Feed L304, M09 with water
cooling
0459 508 990 Spare parts list
- 16 bm38o11a
Edition 110203
Feed L302
Wear parts
Item
Ordering no.
HM1
0455 889 001*
0455 894 001*
Insert tube
Insert tube
For Fe, Ss & cored wire
For Al wire
HM2
0455 886 001*
0455 885 001*
Outlet nozzle
Outlet nozzle
For Fe, Ss & cored wire
For Al wire
HM3
0455 898 001
0215 201 202
Screw
O-ring
(M5x12)
HM4
0455 881 001
Cover plate
HM5
Denomination
Notes
Screw
M4x12
HM6
0193 104 002
Washer
Ø16/5x1
HM7
0367 556 001
0367 556 002
0367 556 003
0367 556 004
Feed roller
Feed roller
Feed roller
Feed roller
For Fe, Ss & cored wire, Ø 0.6 - 0.8 mm, V groove
For Fe, Ss & cored wire, Ø 0.8 - 1.0 mm, V groove
For Fe, SS & cored wire Ø 1.0 - 1.2 mm, V groove
For Al wire, Ø 1.0 - 1.2 mm, U groove
HM8
0466 074 001
Insert tube
HM9
0455 906 001
Spacer sleeve
Included in item HM100
HM10
0455 907 001
Pressure roller
Flat, Included in item HM100
Nut
M8, Included in item HM100
HM11
HM12
0469 835 001
Pressure arm
Included in item HM100
HM13
0456 088 001
Shaft
Included in item HM100
HM14
0455 896 001
Spring
HM15
Nut
M10
HM16
0458 748 002
Insulating washer
HM17
0458 748 001
Insulating bushing
HM18
0156 602 001
0332 318 001
Inlet nozzle
Inlet nozzle
HM19
0191 496 114
Woodruff wedge
For Fe, Ss, Al & Cored wire, Ø 2 mm plastic for 0.6-1.6 mm
For Fe, Ss & Cored wire, Ø 2.4 mm steel for 1.2-2.0 mm
* Insert tube 0455 889 001 and outlet nozzle 0455 886 001 must be used together.
Insert tube 0455 894 001 and outlet nozzle 0455 885 001 must be used together.
PARTS SET
Item
Ordering no.
Denomination
HM100
0367 529 001
Pressure arm compl.
Notes
Includes item HM9, HM10, HM11, HM12 and HM13
Welding with aluminium wire
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.
- 17 bm38whm1
R0459
508/E110203/P24
Feed L302
- 18 bm38whm1
R0459
508/E110203/P24
Feed L304
HD = Heavy Duty
Item
Ordering no.
Denomination
Notes
HN1
0455 072 002
0456 615 001
Intermediate nozzle
Intermediate nozzle
For Fe, Ss & cored wire
For Al Wire
HN2
0469 837 880
0469 837 881
Outlet nozzle
Outlet nozzle
For Fe, Ss & cored wire, Ø 2.0 mm steel for 0.6-1.6 mm
For Al wire, Ø 2.0 mm plastic for 0.8-1.6 mm
HN3
0191 496 114
Woodruff wedge
HN4
0459 440 001
Motor gear euro
HN5
Washer
Ø 16/5x1
HN6
Screw
M4x12
HN7
Screw
M6x12
HN8
Washer
Ø 12/6.4x1.5
HN9
0469 838 001
Cover
HN10
0458 722 880
Axle and Nut
HN11
0369 557 001
0369 557 002
0369 557 003
Feed roller
Feed roller
Feed roller
For Fe, Ss & cored wire, Ø 0.6 & 0.8 mm, V groove
For Fe, Ss & cored wire, Ø 0.8 & 1.0 mm, V groove
For Fe, Ss & cored wire, Ø 1.0 & 1.2 mm, V groove
0369 557 004
0369 557 013
0369 557 011
0369 557 006
Feed roller
Feed roller
Feed roller
Feed roller
For Cored wire, Ø 1.0 & 1.2 mm, V-Knurled groove
For Cored wire, Ø 1.4 & 1.6 mm, V-Knurled groove
For Al wire, Ø 0.8 & 0.9 mm, U groove
For Al wire, Ø 1.0 & 1.2 mm, U groove
HN12
0459 441 880
Gear adapter
HN13
0455 049 001
Inlet nozzle
HN14
0455 906 001
Spacer sleeve
HN15
0455 907 001
Pressure roller
HN16
0215 702 708
Locking washer
HN17
0459 518 001
Axel pressure roll
HN18
Nut
HN19
0458 748 002
Insulating washer
HN20
0458 748 001
Insulating bushing
HN21
0156 602 001
0332 318 001
Inlet nozzle
Inlet nozzle (HD)
Flat
M10
For Fe, Ss, Al & Cored wire, Ø 2 mm plastic for 0.6-1.6 mm
For Fe, Ss & Cored wire, Ø 2.4 mm steel for 1.2-2.0 mm
Welding with aluminium wire
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.
- 19 bm38whn1
R0459
508/E110203/P24
Feed L304
- 20 bm38whn1
R0459
508/E110203/P24
Feed L302, Feed L304
Accessories
1
Bobbin cover, plastic Ø 300mm . . . . . . . . . . . 0458 674 880
1
Adapter for 5 kg bobbin . . . . . . . . . . . . . . . . . . . . 0455 410 001
1
2
Lifting eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0458 706 880
Brake hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0146 967 881
1
2
Turning piece . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0458 703 880
Quick connector MarathonPact . . . . . . . . . . . F102 440 880
1
Wheel kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0458 707 880
- 21 bm38a11a
R0459
508/E110203/P24
Feed L302, Feed L304
1
Strain relief for welding gun . . . . . . . . . . . . . . 0457 341 881
Strain relief bracket for connection set . . . . 0459 234 880
Counter balance device . . . . . . . . . . . . . . . . . . . 0458 705 880
(includes mast and counter balance)
Water kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 564 880
Connection set
Connection set 1.7 m . . . . . . . . . . . . . . . . . . . . . .
Connection set 5 m . . . . . . . . . . . . . . . . . . . . . . . .
Connection set 10 m . . . . . . . . . . . . . . . . . . . . . . .
Connection set 10 m, water . . . . . . . . . . . . . . . . .
- 22 bm38a11a
R0459
0459 532 880
0459 532 881
0459 532 882
0459 532 892
508/E110203/P24
NOTES
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
- 23 notes
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
ESAB AB
SE-695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
101217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising