EASYBus-display and monitoring device for 9 channels

EASYBus-display and monitoring device for 9 channels
Handheld instrument
EASYBus-display and monitoring device for 9 channels
Front
48 x 96

s
.Bu
.S.Y
E.A Modul
-

Temperature probe
Transmitter
Logger / EASYBus
Display / Controller

EB 2000 MC
Specification
Measuring range: -1999 to +9999 digit
Resolution: automatic detection of resolution of connected sensor modules. Automatic positioning of decimal point.
Accuracy: depending on sensor module used. The EB2000MC
transfers this value digitally without any additional fault.
Sensor modules: (not included in scope of supply)
all intelligent EASYBus sensor modules as well as EASYLOG
(max. 9) can be connected. 2-wire connection in ring-, tree- or star
type. No polarity, max. cable length: 200m.
Sensor supply: via EB 2000 MC.
Fault messages: sensor damage, sensor short circuit, values
above/below permissible area.
Self diagnosis: const. monitoring to ensure trouble-free function.
Interface: RS232 for easy configuration, or as interface converter
RS232 - EASYBus.
Min./Max. value memory: for up to 9 different sensor modules,
selectable via front side keyboard.
Min./Max. alarm: 2 volt-free relays (make contact), 10A (ohmic
load), 250V, 50/60Hz, for min./max. alarm,
programmable via front side button or RS232-interface.
Alarm delay: from 0 to 9999 minutes, can be set individually for
each channel.
Display: 4-digit, red, 13mm high LED-display. 16 additional LEDs
for display and monitoring functions.
Front: Transparent membrane keyboard IP65. Sealing for
housing for installation according to IP65 will have to be ordered
separately.
Housing: rack-type housing 48 x 96 x 100mm (H x W x D).
Panel cutout: 43 x 90,5 mm (H x W).
Connection terminals: screw-type/plug-in terminals
Ambient temperature: 0 to 50°C (permissible ambient temperature)
Voltage supply: 230V AC 50/60Hz (standard)
Power consumption: approx. 3,5 VA
Options / upcharges
Voltage supply:
12V AC, 24V AC or 115V AC 50/60Hz (others upon request)
Alarm / Protection
Accessories
GGD 4896 (add. sealing for panel mounting acc. to IP65)
GRS 01/9 interface adapter RS232:
(adapter cable to 9-pin PC-interface)
(Please note: order Dsub9 -> Dsub25, if required! - GSA 9S-25B)
EBSK 01 (connection cable 1m, for EASYLOG, EBN, ...)
EBSK 03 (connection cable 3m, for EASYLOG, EBN, ...)
VSL 2P (twisted special cable
per m
for EASYBus-system, cross section 2 x 0,75 mm² )
AKL 1P (special-branch terminal for connection to VSL2P,
2 pieces)
72





The EB 2000 MC is able to display and monitor up to 9
sensor modules or loggers.
The EB 2000 MC automatically detects the number and
type of sensor modules connected (e.g. temperature,
humidity, pressure sensors etc.). Neither sensor adjustment nor re-configuration are required. The display will
always be in the correct dimension.
Sensor module and logger supply as well as data transfer are carried out via one single 2-wire line. No additional voltage supply for sensor modules required.
The EB 2000 MC monitors all sensor and logger functions as well as cable and sensor damage etc. and will
pass an alarm message in case of fault.
The EB 2000 MC is equipped with 2 volt-free relay outputs (make contact) for min./max. alarm.
The EB 2000 MC is equipped with a min./max. value
memory for 9 channels.
Its standard RS232-interface ensures easy configuration.
In addition the EB 2000 MC can be used as a interface
converter RS232 - EASYBus so that all EASYLOGs
connected can be read via the EB 2000 MC. (Software
required: GSOFT40K)
The EB 2000 MC device - cost savings in all areas !
 Short installation time - only one 2-pin line.
 Minimum material requirement - only one display and
monitoring device for up to 9 sensor modules.
 Minimum time requirement for planning and commissioning - automatic sensor module detection, expandable for up to 9 sensor modules of any type whatsoever.
EBS 9M
(nine channel)
Windows-software for low-cost installation of a multi-channel measuring data recording system. (please refer to page 39)
EB 3000
Up to 20 sensor-modules or loggers can be connected

Sensor module supply and data transfer are carried out
via one single 2-wire line. No additional voltage supply
for sensor modules required.

5 relay outputs (4 x controlling, 1 x alarm)

Controller functions can be assigned to any channel, e.g.:
- 4 x two-point-controllers (of 4 arbitrary sensors)
- 2 x three-point-controllers (of 2 arbitrary sensors)
- 4-way switch (of 1 arbitrary sensor), ....

2 calculated channels for displaying:
- average value over more sensors
- difference of 2 sensors
- special functions

Min-/Max- value memory from all sensors callable

Alarm monitoring for all connected sensors

easy configuration via front-side keypad or via interface

Via serial interface the connected devices can be read
or additionally be monitored with a PC.

With EASYBus interface to the PC:
- Up to 1000m cable-length from PC to EB3000 possible
(with interface converter EBW64 or EBW240)
- Additional connection of EASYBus-modules that are
not monitored or connection of a second EB3000 on
the same converter possible.
Specification
Display range: -1999 to +9999 digit
Resolution: automatic detection of resolution and decimal point
of connected sensor modules.
Accuracy: depending on sensor module used. The EB3000 transfers this value digitally without any additional fault.
Sensor modules: (not included in scope of supply)
all intelligent EASYBus sensor modules as well as EASYLOG can
be connected. 2-wire connection in ring-, tree- or star type. No
polarity.
Sensor supply:
via EB 3000
max. bus load:
30 EASYBus standard loads
max. meas. channels: 20
perm. cable length: 500 m (depending on type of cable and wiring)
Switching outputs: 4 relay outputs (make contact), switching to
common terminal.
Outputs can be assigned to any channel
Switching power: 230VAC, 5A, ohm resistive load
Switching function: 2-point controller, 2-point controller inverting
Switching points and delay for each output freely selectable
Alarm output: 1 relay output (change-over contacts)
Switching power: 230VAC, 5A, ohm resistive load
Alarm function:
Common alarm for all sensors.
Alarm-settings of the sensors changeable.
Configuration: All standard-functions can be entered and controlled via keypad.
A configuration software is available for extended configuration
The EB 3000 device - cost savings in all areas !

Short installation time - only one 2-pin line.

polarity must not be observed by installation

Minimum material requirement - only one display and
monitoring device for up to 20 sensor modules

Minimum time requirement for planning and commissioning - automatic sensor module detection, expandable for
up to 20 sensor modules of any type.
Handheld instrument

Display / Controller
s
.Bu
.S.Y
E.A Modul
-
Logger / EASYBus
Front
48 x 96
Transmitter
EASYBus-display and monitoring device for 20 channels
Accessories
GGD 4896 add. sealing for panel mounting acc. to IP65
Sensor, logger modules
p.r.t. page 44, 47 - 50, 60 - 63, 68 -71
for temperature, humidity, norm. signal, frequency, ...
EBW 1 interface converter: EASYBUS to RS232
EBSK 01 connection cable 1m, for EASYLOG, EBN, ...
VSL 2P twisted special cable
per m
for EASYBus-system, cross section 2 x 0,75 mm²
AKL 1P special-branch terminal
or connection to VSL2P, 2 pieces
EASYBus-Configurator
free of charge
Alarm / Protection
Min./Max. value memory: from all connected sensor modules the
max. and min. value are callable via front-side keypad.
Calculation-functions: there are 2 “virtual” channels additionally
to the sensor-channels. A calculated value can be displayed here.
Possible calculation functions: sensor-deviation, averaging above
x sensors, etc.
Self diagnosis: permanent self-diagnosis to ensure trouble-free
function. A corresponding fault massages will shown at an error
(e.g. sensor damage, ..)
Display: 4-digit, red, 13mm high LED-display (meas. value),
2-digit, red, 7mm high LED-display (channel display). 11 additional
LEDs to display the unit, switching state or alarm
Interface: EASYBus-interface
with supported converter (e.g. EBW1) GRS232 compatible, for
communication with a PC.
Housing: rack-type housing 48 x 96 x 100mm (H x W x D).
Front: Transparent membrane keyboard IP65. Sealing for housing
for installation according to IP65 will have to be ordered separately.
Panel cutout: 43 x 90,5 mm (H x W).
Connection terminals: screw-type/plug-in terminals
Ambient temperature: -25 to 50°C (permissible ambient temperature)
Voltage supply: 230V AC 50/60Hz
Power consumption: approx. 9 VA
Temperature probe
(supported converter is needed).
software for comfortable editing of all EB3000-parameters.
(downloadable from our homepage: Service --> Download)
73
Handheld instrument
Display / Controller
Logger / EASYBus
Transmitter
Temperature probe
Alarm / Protection
T-Logg - The logger series for stand-alone applications
TEMPERATURE-LOGGER
for individual programming of
recording time
NE
HUMIDITY-/TEMPERATURE-LOGGER
for individual programming of
recording time
W
T-Logg 100
T-Logg 100 E
T-Logg 120 W
T-Logg 120 K
NE
NE
W
W
TEMPERATURE-REGISTRATION
(16.000 meas. values) for any application
STANDARD SIGNAL REGISTRATION
(16.000 meas. values) for transducers etc.
HUMIDITY- / TEMPERATURE-REGISTRATION
(16.000 meas. values) for any application
T-Logg 100
T-Logg 100 E
T-Logg 120 W - ...
T-Logg 160
T-Logg 120 K - ...
Starter kit
NE
W
Starter kit
(with elbow type plug)
(with PG glanding and cable)
T-Logg 100 SET
Complete set: T-Logg 100 + USB 100 (incl. MINISOFT)
Note: please specify standard signal desired
when ordering
T-Logg 160 SET
Complete set with T-Logg 100 and interface
converter USB 100 (incl. MINISOFT)
Specification
Specification
Specification
Measuring range:
T-Logg 100:
-25,0 ... 60,0 °C
T-Logg 100 E:
-25,0 ... 120,0 °C
Resolution:
0,1 °C
Accuracy (at nominal temperature = 25°C):
T-Logg 100:
±0,5 °C
T-Logg 100 E:
±0.2 of meas. value ±0.5 °C
Sensor:
T-Logg 100:
integrated in device
T-Logg 100 E:
sensor tube made of stainless steel, Ø5 mm, approx.
50 mm long, approx. 1 m
silicone cable. Cable with antibuckling glanding to housing.
Display:
LCD-display, 10 mm high
Recording interval: from 2 sec. to 5 h
free programmable via software
Storage capacity:
16.000 measuring values
Recording time:
166 days (if interval is 15 min.)
Working temperature: -25 to +60 °C
Storage temperature: -30 to +85 °C
Battery:
CR2032, exchangeable
Battery service life: over 3 years
(if recording interval is 15 min.)
Display range:
Measuring ranges, display ranges:
Humidity:
0.0 ... 100.0 %RH
Temperature:
-25.0 ... 60.0 °C
Resolution:
0.1 °C / 0.1 %RH
Accuracy (at nominal temperature = 25°C):
Humidity:
< ±3 % in range 10 - 90 %
Temperature:
± 0,3 °C ± 0.017 * (T - 25°C)
Sensors:
mounted in sensor tube
Sensor tube:
approx. Ø15 mm made of
polyamide with screw-type
plastic protection cap
Display:
10 mm high LCD-display
Recording interval:
from 4 sec. to 5 h
freely programmable via software
Storage capacity:
16.000 measuring values each
Recording time:
166 days
(if interval is 15 min.)
Nominal temperature: 25 °C
Working temperature: -25 to +60 °C
Storage temperature: -30 to +85 °C
Battery:
CR2032, exchangeable
Battery service life: over 3 years
(if recording interval is 15 min.)
-1999 ... 9999 digit
freely programmable
Decimal point
any position
Input signal: only one signal!
0 - 1 V, 0 - 2 V, 0 - 10 V, 0 - 20 mA or 4 - 20 mA
other input signals upon request
(input is not isolated from interface)
Accuracy:
±0,5 % FS (at nom. temperature)
Display :
10 mm high LCD-display
Recording interval:
from 2 sec. to 5 h
freely programmable via software
Storage capacity:
16.000 measuring values
Recording time:
166 days
(if interval is 15 min.)
Working temperature: -25 to +60 °C
Storage temperature: -30 to +85 °C
Battery:
CR2032, exchangeable
Battery service life: over 3 years
(if recording interval is 15 min.)
Electric connection: (for input signals)
... 120 W - ..: elbow-plug in accordance with
DIN43650 for connection to an
existing transmitter.
... 120 K - ..: approx. 0.5 m connection cable
Interface:
serial interface, 3-pin miniature integral plug.
The T-Logg 100 is not suitable for bus operation and is not E.A.S.Y.Bus compatibel!
Housing:
48,5 x 48,5 x 35,5 mm (H x W x D). plugs, sensor connection, ... are not included
Housing made of shock resistant plastic, transparent front made of polycarbonate, splash water-proof: IP 65 (excl. protection cap at T-Logg 160).
Noise immunity (EMC): the T-Logg 100 have been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN61326 (appendix A, class B), additional error: < 0,5% (< 1% at T-Logg 100 E)
Software
MINISOFT
Accessories
free of charge
Read-out software for the T-Logg.
Software is contained at the USB 100 or free
available via the internet (www.greisinger.de).
We will be pleased to send you a separate CD
against a small charge covering our expenses
of € 15,40.
Note: the T-Logg can also be controlled
by the software GSOFT40K.
60
STANDARD SIGNAL LOGGER
for individual programming of
recording time
USB 100 interface converter,
for direct connection of one T-Logg to the USB-interface of a PC.
GWH 40K Wall suspension with lock against theft
(picture: see page 64)
suitable for e.g. T-Logg 100, T-Logg 120 K - ... and T-Logg 160.
GWH 10
Simple wall suspension, made of stainless steel (picture: see page 64)
Mount wall suspension at the monitoring point, logger may now be easily put in.
TEMPERATURE REGISTRATION (48.000 meas. values) for any application.
EASYLOG 40K sensor tube are attached on the device
EASYLOG 40KH sensor tube are connected via 1 m cable
EASYLOG 40KH-E300 tube con. via cable, increased meas. range (0,1°C)
EASYLOG 40KH-E600 tube con. via cable, increased meas. range (1°C)
EASYLOG 40KH-GOF logger with surface probe for pipe mounting
NE
W
WPT3 - Certificate of calibration (not available at ..40KH-GOF)
(measuring points: -20°C / 0°C / +60°C (at ..40K) or -20°C / 0°C / +70°C (at ..40KH))
Specification
Measuring ranges:
EASYLOG 40K:
-25.0 ... 60.0 °C
EASYLOG 40KH:
-50.0 ... 150.0 °C
EASYLOG 40KH-E300: -50.0 ... 300.0 °C
EASYLOG 40KH-E600:
0 ... 600 °C
EASYLOG 40KH-GOF: -50.0 ... 200.0 °C
For special measuring ranges refer to options
Working range (electronic): -25 ... 60°C
Resolution display and memory:
0.1°C or 1°C (corresponding type)
Accuracy (at nominal temperature = 25°C):
EASYLOG 40K:
±0.5°C
EASYLOG 40KH:
±0.5°C
EASYLOG 40KH-E300: ±0.5°C ±0.2% of m.v.
EASYLOG 40KH-E600: ±1°C ±0.2% of m.v.
EASYLOG 40KH-GOF: ±0.5°C ±0.2% of m.v.
Sensor: Pt1000 (2-wire)
- Design 40K: (refer upper picture)
sensor tube made of plastic, Ø7 mm, approx.
30 mm long, attached on the device.
(Note: at certificate: stainless steel tube,
Ø5 mm, approx. 60 mm long)
- Design 40KH: (refer upper picture)
sensor tube made of stainless steel, Ø5 mm,
approx. 50 mm long, approx. 1 m silicone cable.
Cable with anti-buckling glanding to housing.
- Design 40KH-E300: (probe picture below)
sensor tube made of stainless steel, Ø3 mm,
approx. 100 mm long, sleeve Ø5 x 50 mm,
approx. 1 m glass silk cable. Cable with antibuckling glanding to housing.
- Design 40KH-E600: (probe picture below)
sensor tube made of stainless steel, Ø3 mm,
approx. 100 mm long, sleeve Ø5 x 50 mm, flexible coating-element, approx. 1 m silicone cable.
Cable with anti-buckling glanding to housing.
- Design 40KH-GOF: (without picture)
self-adhesive surface temperature probe with
moulded silicone design (type GOF 115 Pt1000
- please refer to page 113)
approx. 2 m PFA-insulated cable. Cable with
anti-buckling glanding to housing.
- Special design types upon request
Display:
10 mm high LCD-display
Recording interval: 2 sec. to 5 h
free programmable via software GSOFT 40K
Storage capacity:
48.000 measuring values
Recording time:
500 days,
(if recording interval is 15 min.)
Battery service life: approx. 6 years (at 15 min)
double battery capacity against upcharge available!
Working temperature (electronic): -25 to +60 °C
Storage temperature: -30 to +70 °C
Interface:
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Note: With an according interface converter you
can connect 120 logger to one RS232-interface
without having any problems.
Housing: 48,5 x 48,5 x 35,5 mm (W x W x D)
sensor and plug not included, IP65.
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN50081-1 and EN50082-1
additional error: < 0,5%
Options (for extra charge)
- DBK: double battery capacity
recommended for high measure-rates
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1 m cable.
Max. switching power: 28 V, 50 mA
- AFK: plugable probe-cable
4-pole (IP65) miniature mounting connector
including assembling of the temperature-probe
to the corresponding connection socket
- SMB: extra measuring range
freely selectable between -200...+600°C.
The essential probe-adjustment is not included
in this price.
Note: at a measuring span <400°C (e.g. ±
200°C) a resolution of 0,1°C is possible. Taller
ranges have a resolution of 1°C
PULSE REGISTRATION
(48000 meas. values) for individual use
EASYLOG 40IMP/S
(type switching contact - with PG-glanding and cable)
EASYLOG 40IMP/T
Handheld instrument
Display / Controller
EASYLOG 40KH
(type TTL-signal - with PG-glanding and cable)
Specification
Measuring range:
Resolution:
Cycle:
Display range:
0 ... 30000 pulses/cycle
1 pulse
2 sec. to 5 h,
free programmable via
software GSOFT 40K
-1999 to 9999 Digit
free programmable
any position
Decimal point:
Input signals:
EASYLOG 40IMP/S: passive volt-free switching
contact
EASYLOG 40IMP/T: active TTL-signal
(input is not isolated for EASYBus)
Resolution display and memory: 1 digit
Accuracy:
cycle time ±50 msec
Display:
10 mm high LCD-display
Recording interval: equal to cycle
Storage capacity:
48.000 measuring values
Recording time:
500 days,
(if recording interval is 15 min.)
Battery service life: approx. 6 years (without
switching current, at 15 min)
double battery capacity against upcharge available!
Working temperature: -25 to +60°C
Storage temperature: -30 to +70°C
Interface:
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Housing: 48,5 x 48,5 x 35,5 mm (L x B x H)
plug and cable not included, IP65
Electric connection: (for input signals)
approx.. 0.5m connection cable, flying leads
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN50081-1 and EN50082-1
additional error: < 0,5%
Options (for extra charge)
- DBK: double battery capacity
recommended for high measure-rates
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1m cable.
Max. switching power: 28V, 50mA
Logger / EASYBus
EASYLOG 40K
s
.Bu
.S.Y
E.A Modul
-
Transmitter
s
.Bu
.S.Y
E.A Modul
-
Temperature probe
s
.Bu
.S.Y
E.A Modul
-
PULSE-LOGGER
for consumption and flow rate measuring, piece counting etc.
Alarm / Protection
TEMPERATURE LOGGER
for watching productioning and server-rooms as well as cooling chambers
according assignation of frozen food 92/1/EWG
61
Handheld instrument
Display / Controller
Logger / EASYBus
Transmitter
Temperature probe
Alarm / Protection
HUMIDITY-/TEMPERATURE-LOGGER
for museums, greenhouses, medicine technology etc.
s
.Bu
.S.Y
E.A Modul
-
s
.Bu
.S.Y
E.A Modul
-
STANDARD SIGNAL LOGGER
replaces for expensive recorders
s
.Bu
.S.Y
E.A Modul
-
EASYLOG 40NS W
EASYLOG 24RFT-E
EASYLOG 24RFT
HUMIDITY- / TEMPERATURE-REGISTRATION
(48.000 measuring values each) for climate monitoring.
STANDARD SIGNAL REGISTRATION
(48.000 meas. values) for transducers etc.
EASYLOG 24RFT
EASYLOG 24RFT-E
EASYLOG 40NS W - ...
WPF4 - Certificate of calibration humidity (measuring points: approx. 20/40/60/80%)
(with PG glanding and cable)
Specification
Note: please specify standard signal desired
when ordering
Measuring range, Display ranges:
Humidity:
0,0 ... 100,0 %RH
Temperature: -25,0 ... 60,0 °C
Display-Options:
Alternative display will shown instead of humidity measuring value.
FK: Wet bulb temperature: -27,0 ... 60,0 °C
TP: Dewpoint temperature: -40,0 ... 60,0 °C
EP: Enthalpy:
-25,0 ... 999,9 kJ/kg
FG: Atmospheric humidity: -0,0 ... 640,0 g/kg
Resolution display and memory:
0.1 °C and 0,1 %RH or 1 digit
Accuracy (at nominal temperature = 25°C):
Humidity:
< ±3 % in range 11-90%
Temperature: ±0,5°C
Sensors:
high-quality capacitive
polymer humidity sensor
and Pt1000 temperature
sensor
Sensor tube:
EASYLOG 24RFT:
Ø15mm made of polyamide
EASYLOG 24RFT-E: approx. Ø14 x 68mm made
of PVDF, connected to
logger via 1m teflon cable
Protection cap:
screw-type plastic
protection cap for quick
responses
Display:
LCD-display, 10 mm high
Recording interval: 4 sec. to 5 h
free programmable via software GSOFT 40K
Storage capacity:
48.000 measuring values
each channel
Recording time:
500 days,
(if recording interval is 15 min.)
Battery service life: approx. 6 years (at 15 min)
double battery capacity against upcharge available!
Working temperature: -25 to +60°C
Storage temperature: -30 to +70°C
Interface:
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Note: With an according interface converter you
can connect 120 logger to one RS232-interface
without having any problems.
(with elbow type plug)
Housing: 48,5 x 48,5 x 35,5 mm (H x W x D)
sensor and plug not included.
Housing made of shock resistant
plastic, transparent front made of
polycarbonate, splash water-proof:
IP 65 (excl. protection cap)
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN50081-1 and EN50082-1
additional error: < 0,5%
Options (for extra charge)
- FK: Wet bulb temperature
- TP: Dewpoint temperature
- EP: Enthalpy
- FG: Atmospheric humidity
- DBK: double battery capacity
recommended for high measure-rates
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1m cable.
Max. switching power: 28V, 50mA
Accessories (p.r.t. page 74, 76/77)
EBW 1
Level converter for connection of up to 9 EASYBus data logger to the RS232-interface of a PC.
(Power supply: 230V/50Hz)
EBW 3
Level converter for connection of one EASYBus
data logger to the USB-interface of a PC.
(Power supply: via USB)
GSOFT 40K incl. EBSK01
(connection cable EBSK01in scope of supply)
Windows software for setting of device, data
readout and printing of the stored data.
(for further description p.r.t. page 65)
EBSK 01
Special connector with approx. 1m cable for the
connection of one EASYLOG.
(note: cable is in scope of supply of the software
GSOFT 40K)
EASYLOG 40NS K - ...
Specification
Display range:
-1999 to 9999 Digit
free programmable
Decimal point:
any position
Input signals: one signal only!
0 - 2 V, 0 - 10 V, 0 - 20 mA or 4 - 20 mA
other input signals upon request
(input is not isolated for EASYBus)
Accuracy:
±0,5% (at nom. temperature)
Display:
10 mm high LCD-display
Recording interval: 2 sec. to 5 h
free programmable via software GSOFT 40K
Storage capacity:
48.000 measuring values
Recording time:
500 days,
(if recording interval is 15 min.)
Battery service life: approx. 6 years (at 15 min)
double battery capacity against upcharge available!
Working temperature: -25 to +60°C
Storage temperature: -30 to +70°C
Interface:
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Housing: 48,5 x 48,5 x 35,5 mm (L x B x H)
(with elbow-plug: 48,5 x 48,5 x 35,5 mm),
splash water-proof IP65
Electric connection: (for input signals)
... 40NS W: elbow-plug in accordance with
DIN43650 for connection to an
existing transmitter.
... 40NS K: approx. 0.5 m connection cable
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN50081-1 and EN50082-1
additional error: < 0,5%
Options (for extra charge)
- DBK: double battery capacity
recommended for high measure-rates
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1m cable.
Max. switching power: 28V, 50mA
Attention: Our software GSOFT40K as well as a level converter (EBW1, EBW3, EBW64 or EB2000MC)
are required for all EASYLOG devices for configuration and to read-out logger data. (p.r.t. p. 65 a. 74)
62
● Various additional measurement categories
are available: dew point temperature, wet
bulb temperature, enthalpy, atmospheric
humidity or absolute humidity
STATE REGISTRATION
(48000 meas. values) for individual use
EASYLOG 40BIN
HUMIDITY - / TEMPERATURE - / PRESSURE - REGISTRATION
(each 250.000 measured values) for climatic applications.
EASYLOG 80CL
WPF4 - Certificate of calibration humidity (measuring points: approx. 20/40/60/80%)
WPD5 - Certificate of calibration pressure (measuring points 300/500/700/900/1100 hPa)
Specification
General
Input signal:
The EASYLOG 80CL can be configured, started and stopped by its buttons. It is possible to record
max. 64 recording sequences (=start/stop processes) with max. 250.000 data sets (humidity/temperature/air pressure).
The device can also be configured and handled by the comfortable software GSOFT40K. There is
the possibility to block the stopping of the logger by the buttons to protect the logger of unauthorised handling.
The device supports the display of units relevant for the air conditioning technology: wet bulb temperature, dew point temperature, enthalpy, atmospheric humidity or absolute humidity.
The EASYLOG 80CL provides a big variety of additional functions:
- SeaLevel correction: instead of the barometric air pressure the pressure at sea level can be display
(input of height above sea level needed).
- Min-/max- value memory: callable by the buttons, the highest and lowest value since the start (or reset) of
the logger is saved here.
- Min-/max- alarm function: the exceeding of adjustable min-/max- alarm boundaries by the displayed value
is monitored. Optional: alarm output for alarm message of the logger available!
passive volt-free switching
contact
(input is not isolated for EASYBus)
Measuring values:
1 = contact is closed (R < 50 Ohm)
0 = contact is open (R > 20 kOhm)
Cycle:
2 sec. to 5 h,
free programmable via
software GSOFT 40K
Resolution display and memory: 1 digit
Display:
10 mm high LCD-display
Recording interval: equal to cycle
Storage capacity:
48.000 measuring values
Recording time:
500 days,
(if recording interval is 15 min.)
Battery service life: approx. 6 years (without
switching current, at 15 min)
double battery capacity against upcharge available!
Working temperature: -25 to +60°C
Storage temperature: -30 to +70°C
Interface:
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Note: With an according interface converter you
can connect 120 logger to one RS232-interface
without having any problems.
Housing: 48,5 x 48,5 x 35,5 mm (L x B x H)
plug and cable not included, IP65
Electric connection: (for input signals)
approx.. 0.5m connection cable, flying leads
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN50081-1 and EN50082-1
additional error: < 0,5%
Options (for extra charge)
- DBK: double battery capacity
recommended for high measure-rates
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1m cable.
Max. switching power: 28V, 50mA
Specification
Measuring range, Display ranges:
Humidity:
0,0 ... 100,0 %RH
Temperature: -25,0 ... +60,0 °C
Air pressure: 300,0 ... 1100,0 hPa
Additional available display ranges:
Wet bulb temperature:
-27,0 ... 60,0 °C
Dewpoint temperature:
-40,0 ... 60,0 °C
Enthalpy:
-25,0 ... 999,9 kJ/kg
Atmospheric humidity:
-0,0 ... 640,0 g/kg
Absolute humidity:
0,0 ... 200,0 g/cm³
Resolution display and memory:
0.1 °C, 0,1 %RH and 0,1 hPa or 1 digit
Accuracy:
Humidity:
± 2 % in range 10-90%
Temperature: ± 0,3 °C ± 0.017 * (T - 25°C)
Air pressure: ± 1.0 hPa (typ., at 0 - 60°C)
Sensoren:
Humidity/Temp.: sensor mounted in sensor tube
(sensor is exchangeable)
Air pressure: sensor integrated in housing
Sensor tube: Ø15 mm made of polyamide
Protection cap: screw-type plastic protection
cap for quick responses
Display:
two 4½-digit LC-displays
Recording interval: 4 sec. to 5 h
free programmable via buttons on the device or
via the software GSOFT 40K
Storage capacity:
250.000 data sets (humidity,
Recording time:
Battery service life:
Working temperature:
Storage temperature:
Interface:
7 years (at 15 min. interval)
approx. 5 years (at 15 min)
-25 to +60°C
-30 to +70°C
EASYBus-interface
3-pin mini-integral plug.
Needed connection-cable EBSK01 not included
in delivery (see accessories page 76)
Note: With an according interface converter you
can connect 120 logger to one RS232-interface
without having any problems.
Housing: 48,5 x 48,5 x 35,5 mm (H x W x D)
sensor and plug not included.
Housing made of shock resistant
plastic, transparent front made of
polycarbonate, splash water-proof:
IP 65 (excl. protection cap)
Noise immunity (EMC): the EASYLOG have
been manufactured in accordance with the regulations concerning EMC (2004/108/EG).
The device meets EN61326 (appendix A, class B)
additional error: < 0,5%
Options (for extra charge)
- ALARM: additional alarm-output
open-collector output via 4-pole miniature
mounting connector (IP65) including 1m cable.
Max. switching power: 28V, 50mA
temperature, air pressure)
in max. 64 recording sequences
Handheld instrument
● big storage for up to 250.000 measuring
values for each unit (humidity, temperature,
air pressure, ...) (= 1.000.000 values for all)
Display / Controller
● up to 64 recording sequences can be saved
Logger / EASYBus
● double display (i.e. to display humidity and
temperature at the same time)
Transmitter
The new generation of the logger series
s
.Bu
.S.Y
E.A Modul
-
Temperature probe
s
.Bu
.S.Y
E.A Modul
-
HUMIDITY-/TEMPERATURE-/AIR PRESSURE LOGGER
for climate monitoring etc.
Alarm / Protection
STATE-LOGGER
for state monitoring etc.
Please Note: For trademark reasons we currently do not deliver members of the EASYLOG family to GB
and USA. Please order there the constructional identical types: Logger type 40K, Logger type 40RF, ...
63
Handheld instrument
EASYLOG - accessories
ESK-1
GWH 40K wall suspension with lock as protection against theft suitable for all EASYLOG (with the exception of EASYLOG 40NS W), EBN/K - ...,
and also for GIA 0420 WK and GRA 0420 WK.
Scope of supply: Mounting plate with nut for instrument mounting,
2 screws, 2 dowel, lock with keys
Display / Controller
external starting key, independent from mains supply to start logger of the type EASYLOG 40... and EASYLOG 24... in the start mode St.Et
Power supply:
9 V DC - via integrated 9V-battery,
Dimensions: 107 x 62 x 26,5 mm (H x W x D)
GWH 10
simple wall suspension, made of stainless steel, for all EASYLOG (except EASYLOG 40NS W).
mount wall suspension at the monitoring point, the logger may now be easily put in.
Scope of supply:
wall suspension
EBW 1
EASYBus - interface converter, RS232
p.r.t. page 74 EBW 3
EASYBus - interface converter, USB
p.r.t. page 74 Logger / EASYBus
GSOFT 40K Windows software for handling the EASYLOG (incl. EBSK 01)
EBSK 01
p.r.t. page 65
Special plug with approx. 1 m cable for connection of a EASYLOG, EBN.. to the EASYBus
EASYBus - Remote Operation System for dataloggers
By using the software GSOFT40K in addtion to the local control of loggers connected at Your work place or laptop computer, they can be
operated remotely covering large distances. This is made possible by using MODEMs and conventional or mobile telephone nets. The loggers can be directly connected to the EASYBus-MODEMs just by using a level converter, no additional PC is needed!
Transmitter
Your advantages
With the EASYBus remote operation system any number of remote locations can be controlled from a single working place. Expensive journeys over hundreds of kilometres aren't necessary any more for the most of the cases, all necessary information is available
directly at the working place. Installation and putting into operation is as easy as possible. The operation of GSOFT40K is basically
the same as it used to be before. The comfortable configuration software MODKonfig (in scope of supply of GSOFT40K) gives a
maximum help when setting up your industry MODEM - without necessary previous knowledge about remote data transfer. With this
powerful tools You are enabled to setup the complete reliable system within minutes.
Simple Installation:
Extended system with SMS alarm function:
Alarm / Protection
Temperature probe
Alarm by SMS
message
64
ne
ho
lep
te
line
ne
te
ho
lep
line
Extended system with SMS alarm function
As a special feature an alarm message may be sent to your mobile phone (SMS) when using e.g. an EB2000MC / EB3000 or an
EBUW232A with a interface converter (EBW1, EBW64 oder EBW240). (MODEM 2500 or MODEM 3500 GSM required for SMS).
For example an alarm message is sent if a selectable temperature range is exceeded.
One or more alarm outputs of the used components are connected to the alarm input of the MODEM.
In case of an alarm the presetable alarm message is sent as SMS message to the mobile phone. When then message was received
the operator may e.g. connect to the remote location by using GSOFT40K to take a closer look on what is going on.
Required Components:
-For the working place commonly analog MODEMs will be supported, which also may be connected to ISDN nets via a suitable
terminal adapter.
-The MODEM of the remote location is a EASYBus - taylored industry MODEM (MODEM 1000, MODEM 2500, MODEM 3500 GSM).
-If there isn't any telephone connection available at the remote location, or if it is a mobile system, it is possible to use the mobile
GSM-MODEM. The MODEM 3500 GSM e.g. supports 900MHz mobile telephone nets and is approved for european use. It works
like a mobile phone with integrated MODEM. Common SIM cards are supported. It just to be made sure that data transfer is unlocked by the mobile net provider.
Operating software for EASYLOG, MINILOG and T-Logg datalogger
GSOFT40K is the comfortable operation software for the very easy operation of the EASYLOG’s (MINILOG’s) and T-Logg´s.
The software supports English, German and Czech language and is executable with Windows 98, Me, NT, 2000, XP and Vista.
Comfortable user interface - the essentials on a glance:
The programme is menu driven, the most important commands are additionally available in a toolbar. Whenever necessary the software gives hints and messages. Therefore any user with a few basics about how to operate standard Windows software will be able
to operate it. Loggers can be connected, started and read out by single mouseclicks.
Display of logger state informations
The loggers are supporting alarm functionality - easily configurable by the GSOFT40K Software. All other
important logger settings are displayed, too. E.g. a label
up to 16 characters long can be assigned to each logger channel, which is stored in the logger. You may for
example label the location or other useful details by using
this function.
Additional entering of remarks
If You have read out a logger and want to store the data
on disk or harddisk there is the possibility to additionally
enter remarks of any length for each recording, for example to describe and comment unusual occurrences during
the recording.
The data: Tables and diagrams
After reading out the recordings the data will be displayed in form of a table. With the diagram the data of
several loggers can be displayed simultaneously. Additional diagram functions:
• labelling of measuring values
• real time axis
• zooming of any section within the diagram
• legend (inactivate able)
• measurement cursor (inactivate able)
• marking of measurings with symbols
(inactivate able)
The main target of the design of GSOFT40k was most
easiest operationability, therefore just a few easy mouseclicks are necessary to display data fast and clear. Both
diagrams and tables are displaying the data in realtime,
even daylight savings time settings are taken into account automatically. And of course tables and diagrams
can be printed out.
E.A.S.Y.Bus & simultaneous operation and display of several loggers
Because of the EASYBus more than one logger can be connected at the same time at a single serial PC interface. Distances of up
to 1000 m can be covered. To simplify operation all connected loggers can be operated at the same time. This reduces the expense
of operation time and even largest EASYBus-systems can be controlled easily.
Remote operation via conventional and mobile telephone nets
Transmitter
Setting of special functions
Logger / EASYBus
Display / Controller
All necessary informations are compressed to a single
clearly arranged window for each connected logger.
Handheld instrument
(incl. connection cable EBSK01)
Temperature probe
GSOFT 40K
Automated Read Out
All loggers connected directly or via conventional an mobile telephone nets can be read out automatically. The points of time can be
entered separately (e.g. each day lor each week ... at X.XX o'clock), the read out data will be archived on hard disk.
The system gets even more reliable and the handling of multiple loggers gets much easter.
Export function
To be able to use the logger data with other software applications (EXCEL, WORD,... ), a flexible export function is integrated. The
data can be converted to textfiles which can be processed by all popular programmes.
Alarm / Protection
With GSOFT40k loggers can be operated and read out via any distance by the means of the conventional or the mobile telephone
nets. Because of this feature measuring values and recordings can be collected centrally covering distances of hundreds of kilo
meters. (p.r.t. page 64 and 77)
Update GSOFT 40K
(for registered users with declaration of serial number of original version)
Update can downloaded freely from our homepage (prerequisite: existence version > 7.0)
65
Display / Controller
Handheld instrument
EASYBus - interface converter
EBW 1
interface converter
for connection of max. 9 EASYBus-modules to the RS232-interface
(9-pin Dsub) of your PC.
Scope of supply: interface converter, 9-pin Dsub extension cable
EBW 2
main supply independent interface converter
for connection of one EASYBus-module (e.g. EASYLOG ) to the RS232interface (9-pin Dsub) of your PC.
(Power supply via integrated 9V-battery)
Scope of supply: interface converter incl. 9V-battery,
9-pin Dsub extension cable
EBW 3
interface converter
for connection of one EASYBus-module (e.g. EASYLOG ) to the USBinterface of your PC. (Power supply: via USB)
Scope of supply: interface converter
NE
W
EBW 64 interface converter
Alarm / Protection
Temperature probe
Transmitter
Logger / EASYBus
for connection of max. 64 EASYBus-modules to the RS232-interface
of your PC.
Scope of supply: interface converter, 9-pin Dsub extension cable
EBW 240 incl. software EASYControl
interface converter for connection of max. 240 EASYBus-modules
to the RS232-interface of your PC.
Scope of supply: interface converter, plug-in power adapter, 9-pin Dsub
extension cable, software EASYControl.
Specification:
EBW 1
EBW 2
EBW 3
EBW 64
EBW 240
Voltage supply:
230 V AC / 50Hz
9 V - battery
not necessary
230 V AC / 50Hz
230 V AC / 50Hz
Power consumption:
approx. 5 W
(over power adapter)
max. 1 W
max. 0.5 W
approx. 15 W
approx. 30 W
Max. permissible sensor modules *: 9
1
1
64
240
Permissible cable length **:
200 m
10 m
10 m
1000 m
1000 m
Baud rate:
4800 Baud
Serial connection:
RS232
RS232
USB
RS232
RS232
Electrical isolated:
yes
no
yes
yes
yes
Overload display:
no
no
no
yes
yes
Short-circuit proof:
yes
yes
yes
yes
yes
Operating temperature:
0 ... 50 °C
0 ... 50 °C
-25 ... 50 °C
0 ... 50 °C
0 ... 55 °C
Humidity:
20 ... 80 %RH, non-condensing
Storage temperature:
-20 ...+70 °C
-20 ...+70 °C
-25 ...+70 °C
-20 ...+70 °C
-20 ...+60 °C
Dimensions (H x W x D):
112 x 80 x 45 mm
107 x 62 x 26 mm
56 x 31 x 24 mm
100 x 75 x 110 mm 200 x 240 x 55 mm
(without power adapter)
* depending on type of the used sensor modules
** depending on type of cable and wiring
Interface accessories
USB-Adapter for connection of an interface converter to the USB-interface of yout PC
GRS 02/9
interface cable fotEBW 2 for connection to a MODEM ...
GSA 9S-25B connection-adapter: 9-pin Dsub-plug <=> 25-pin Dsub-socket
Note: the EASYBus-monitoring device EB2000 should be can used as a converter for max. 9 sensor modules.
74
Software for initial installation and configuration of EASYBus-systems.
Software executable with: Windows 2000, XP and Vista.
●
EASYBus modules, display- and controlling-devices can be handled easily and comfortably.
●
Listing of all connected modules in a treeview, therefore an easy
overview of the system is possible.
●
Settings of EASYBus modules can be done clearly.
●
Easy installation of the EB3000 control-, display- and monitoringdevice:
- Adding of modules via Drag&Drop.
- Programming of predefined virtual channel functions
(included in software).
- Switching- and alarm-outputs can be configured easily.
You can download this software from our homepage
(www.greisinger.de) for free.
Handheld instrument
free of charge
Display / Controller
EASYBus-Configurator
Software for recording, monitoring and displaying up to 9 sensor
modules of the EASYBus-series.
Software executable with: Windows 98, Me, NT, 2000 and XP.
The software contains 3 modules.
● Recording / large digit display: Measurement is displayed during
ongoing recording. The display type of each channel can be switched
form large-digit-display to chart recorder during operation.
Logger / EASYBus
EBS 9M
● Data display: Stored data sets can be displayed.
Software for recording, monitoring, display and documentation of up to 240
sensor modules of the EASYBus-series.
Software executable with: Windows 98, Me, NT, 2000 and XP.












min./max. value monitoring for each measuring point
straightforward display of current measuring values in form of table
simple sorting of sensor module sequ. by means of drag and drop
scanning cycle for each sensor module can be individually selected
adding and deleting of sensor modules during recording operation
display of measuring values as diagram or table
separate fault list
automatic system initialization with detection of all sensor modules connected
automatic detection of new sensor modules
fully automatic assignation and administration of bus addresses
aut. detection of sensor module type, meas. range and meas. unit
alarm supervision with EBB 4 OUT / ... - module (each one relais: min-, max-alarm,
alarm in general)
The only thing left for you to do is entering your description!
Advance notice:
The software EASYControl is currently being redesigned. At press time of this catalogue an exact publication issue was not fixed.
Temperature probe
EASYControl
Alarm / Protection
For further information please refer also to page 39.
Transmitter
● Export-Tool: For modification of stored data files to use the data in
other programs (e.g. Excel).
Please observe our announcements at our website.
75
Handheld instrument
Display / Controller
Logger / EASYBus
EASYBus - components
Sensor modules
Logger module (for temperature, humidity, pressure, norm. signals, frequency)
Sensor module (for temperature, humidity, norm. signals, frequency, ...)
GIA 20 EB EASYBus module for norm. signal and temperature, with 2 switching outputs
GIA 2000 EASYBus module for norm. signal and temperature
GIR 2002 EASYBus module for norm. signal and temperature, with 2 relay outputs
p.r.t. page 61 - 63
p.r.t. page 68 - 71
p.r.t. page 42
p.r.t. page 46
p.r.t. page 48
EBB 1 IN EASYBus sensor module with 1 digital input to monitor a electrically insulated contact
EBB 4 IN EASYBus sensor module with 4 digital input to monitor a electrically insulated contact
Input:
Housing:
Dimensions:
EBB 1 IN: 1 digital input for electrically insulated contact
EBB 4 IN: 4 digital input for electrically insulated contact
snap-on housing
approx. 22.5 x 78 x 105 mm
s
.Bu
.S.Y
E.A Modul
-
Logger accessories
ESK-1
external starting key, independent from mains supply
p.r.t. page 64
to start logger of the type EASYLOG 40... and EASYLOG 24... in the starting mode St.Et
GWH 40K wall suspension with lock as protection against theft
p.r.t. page 64
GWH 10
p.r.t. page 64
suitable for all EASYLOG (except EASYLOG 40NS W), EBN/K - ..., GIA0420WK and GRA0420WK
simple wall suspension, made of stainless steel,
suitable for all EASYLOG (except EASYLOG 40NS W).
mount wall suspension at the monitoring point,
the logger may now be easily put in.
Cable
EBSK 01 special plug with approx. 1 m of cable for connection of one EASYLOG, EBN.. to the EASYBus
EBSK 03 special plug with approx. 3 m of cable for connection of one EASYLOG, EBN.. to the EASYBus
EBSK 10 special plug with approx. 10 m of cable for connection of one EASYLOG, EBN.. to the EASYBus
Transmitter
(Please note: the EASYLOG will be supplied without connection cable. The GSOFT40K includes a connection cable EBSK01.
Please order EBSK01, EBSK03 resp. EBSK10 as required in case of permanent bus connection!)
VSL 2P
AKL 1P
twisted special cable for EASYBus-system, cross section 2 x 0,75 mm²
per m
special branch terminal for connection to VSL2P, 2 pieces
Alarm / Protection
Temperature probe
Interface converter
EBW 1, EBW 64, EBW 240 EASYBus interface converter, RS232, main supply
EBW 2
EASYBus interface converter, RS232, battery supply
EBW 3
EASYBus interface converter, USB
EB 2000 MC EASYBus-display and monitoring device for 9 channels
p.r.t. page 74
p.r.t. page 74
p.r.t. page 72
Interface accessories
USB-Adapter
GRS 01/9
GRS 02/9
GSA 25S-9B
GSA 9S-25B
for converter connection to an USB interface
interface cable for EB2000 MC for connection to 9-pin RS232 interface of a PC
interface cable for EBW2 for connection to a MODEM ...
connection-adapter: 25-pin Dsub-plug <=> 9-pin Dsub-socket
connection-adapter: 9-pin Dsub-plug <=> 25-pin Dsub-socket
Software
EBS 9M
Windows software for recording and archiving of max. 9 sensor modules
EASYControl
Windows software for monitoring of max. 240 sensor modules
GSOFT 40K
Windows software to service the EASYLOG
ProfiLab-Expert Windows software
EASYBUS.dll Windows-function library for interface communication EASYBus - PC,
to integrate in your own programmes
76
p.r.t. page 74
p.r.t. page 39
p.r.t. page 75
p.r.t. page 65
p.r.t. page 39
6 - 12 V DC, max. 10 mA (connection over approx. 50 cm adapter cable)
NPN open-collector,
max. switching capacity: 24 V, 50 mA (connection over adapter cable)
GNG 12 - LE plugin power supply 12 V DC / 300 mA
GNR 232 A Power supply and relay module for EBUW 232 A
Power supply:
Outout voltage:
Relay output:
Connection:
Dimensions:
EB 2000
EB 3000
230 V, 50/60 Hz
12 V DC ±5% (regulated) 25 mA
volt-free changeover contacts, switching current max. 10 A ohmic load
screw-type terminal
96 x 61 x 60 mm (H x B x T)
EASYBus-display and monitoring device for 9 channels
p.r.t. page 72
EASYBus-display, regulating and monitoring device for 20 channels
p.r.t. page 73
Switching modules
EBB 2 OUT / BP
EBB 2 OUT / 12V
EBB 4 OUT / BP
EBB 4 OUT / 12V
EASYBus switching module, 2 relay, bus-powered
EASYBus switching module, 2 relay
EASYBus switching module, 4 relay, bus-powered
s
.Bu
.S.Y
E.A Modul
-
EASYBus switching module, 4 relay
The EBB ... OUT / ... are switching modules for the EASYBus that can be arbitrarily placed on a location in
the bus system. The control of the modules' relays is realized by an alarm monitoring module EBUW232A
or by PC-software (e.g. EASYControl).
There are 2 different design types of the switching modules:
... / BP: Bus Power - no external auxiliary supply needed
... / 12V: external 12V-supply needed - this allows faster switching and a higher operating reliability due to
adjustable preferred relay states in case of a system failure. (Power supply unit not in scope of supply)
Power supply:
Switching outputs:
Switching reaction:
Switching power:
Connection:
Dimensions:
EBB 2 OUT / BP EBB 4 OUT / BP
Powered by the EASYBus
2 changers
4 changers
< 1 seconds
< 2 seconds
max. 250 V AC / 16 A ohmic load
screw type terminal
96 x 48 x 60 mm 96 x 94 x 60 mm
EBB 2 OUT / 12V EBB 4 OUT / 12V
12 V DC ±10% / 150 mA
2 changers
4 changers
< 0.1 seconds
< 0.1 seconds
96 x 48 x 60 mm
96 x 94 x 60 mm
Remote operation
MODEM 1000 analog standard industry-MODEM
refer to homepage
MODEM 2500 analog hat rail MODEM with alarm input and SMS alarm
refer to homepage
MODEM 3500 GSM GSM MODEM with alarm input and SMS alarm
refer to homepage
for the EASYBus remote data transfer via analog telephone nets.
for the EASYBus remote data transfer via analog telephone nets.
for the EASYBus remote data transfer via 900MHz mobile nets (D1, D2, etc.).
DFM 232 SET Wireless data connection, 433MHz, consisting of transmitter and receiver
for wireless data transmission to EASYBus-modules via 433Mhz radio network.
Bi-directional RS232 interface (DB9), e.g for the connection of EBW 1,
large range of up to 1500 m at free air, within buildings similar to DECT telephones.
LAN 3000 Serial-to-Ethernet-Converter
for remote access to EASYBus-modules via LAN or Internet.
Serial RS232 Input (DB-9) e.g. for EBW1, 1* LAN Port RJ-45 10/100Mbps
Supported protocols: TCP, DHCP, HTTP, etc.
Network connection via: Stat. IP, DHCP or PPPoE
Handheld instrument
Display / Controller
Power supply:
Switching output:
Logger / EASYBus
The EBUW232A monitores independently, it means without additional PC up to 240 EASYBus-modules
for their alarm conditions. If an alarm is present, the alarm output of the EBUW 232 A will be set.
With the included adapter cable the relay module GNR 232 A can be controlled. Additionally an adequate
to the bus connected switching module (EBB .. OUT) can be controlled.
Transmitter
EBUW 232 A independent alarm monitoring module for EASYBus-modules
Temperature probe
Alarm monitoring
Alarm / Protection
EASYBus - components
77
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement