Sony RDR-HX510 User manual

Sony RDR-HX510 User manual
2-589-941-12(1)
DVD Recorder
Operating Instructions
RDR-HX510
© 2005 Sony Corporation
CAUTION
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
The mains lead must only be changed
at a qualified service shop.
The use of optical instruments with this
product will increase eye hazard. As
the laser beam used in this DVD
recorder is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel
only.
Precautions
This equipment has been tested and
found to comply with the limits set
out in the EMC Directive using a
connection cable shorter than 3
metres.
On safety
Should any solid object or liquid fall
into the cabinet, unplug the recorder
and have it checked by qualified
personnel before operating it any
further.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the laser
protective housing inisde the
enclosure.
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product
shall not be treated as household waste.
Instead it shall be handed over to the
applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative
consequences for the environment and
human health, which could otherwise
be caused by inappropriate waste
handling of this product. The recycling
of materials will help to conserve
natural resources. For more detailed
information about recycling of this
product, please contact your local city
office, your household waste disposal
service or the shop where you
purchased the product.
About the hard disk drive
This label is located on the laser
protective housing inside the
enclosure.
Notice for customers in the
United Kingdom and Republic of
Ireland
A moulded plug complying with
BS1363 is fitted to this equipment for
your safety and convenience.
Should the fuse in the plug supplied
need to be replaced, a 5 AMP fuse
approved by ASTA or BSI to BS1362,
(i.e., marked with
or
mark)
must be used.
If the plug supplied with this
equipment has a detachable fuse cover,
be sure to attach the fuse cover after
you change the fuse. Never use the
plug without the fuse cover. If you
should lose the fuse cover, please
contact your nearest Sony service
station.
Precautions
• This unit operates on 220 – 240 V
AC, 50/60 Hz. Check that the unit’s
operating voltage is identical with
your local power supply.
• To prevent fire or shock hazard, do
not place objects filled with liquids,
such as vases, on the apparatus.
VIDEO Plus+ and PlusCode are
registered trademarks of Gemstar
Development Corporation.
The VIDEO Plus+ system is
manufactured under license from
Gemstar Development Corporation.
The hard disk has a high storage
density, which enables long
recording durations and quick
access to the written data. However,
it can easily be damaged by shock,
vibration or dust, and should be kept
away from magnets. To avoid losing
important data, observe the
following precautions.
• Do not apply a strong shock to the
recorder.
• Do not place the recorder in a
location subject to mechanical
vibrations or in an unstable
location.
• Do not place the recorder on top of
a hot surface, such as a VCR or
amplifier (receiver).
• Do not use the recorder in a place
subject to extreme changes in
temperature (temperature gradient
less than 10 °C/hour).
• Do not move the recorder with its
mains lead connected.
• Do not disconnect the mains lead
while the power is on.
• When disconnecting the mains
lead, turn off the power and make
sure that the hard disk drive is not
operating (the clock is displayed in
the front panel display and all
recording or dubbing has stopped).
• Do not move the recorder for one
minute after you have unplugged
the mains lead.
• Do not attempt to replace or
upgrade the hard disk by yourself,
as this may result in malfunction.
If the hard disk drive should
malfunction, you cannot recover lost
data. The hard disk drive is only a
temporary storage space.
2
About repairing the hard disk
drive
• The contents of the hard disk drive
may be checked in case of repair
or inspection during a malfunction
or modification. However, the
contents will not be backed up or
saved by Sony.
• If the hard disk needs to be
formatted or replaced, it will be
done at the discretion of Sony. All
contents of the hard disk drive will
be erased, including contents that
violate copyright laws.
On power sources
• The recorder is not disconnected
from the AC power source (mains)
as long as it is connected to the
wall outlet, even if the recorder
itself has been turned off.
• If you are not going to use the
recorder for a long time, be sure to
disconnect the recorder from the
wall outlet. To disconnect the AC
power cord (mains lead), grasp the
plug itself; never pull the cord.
• Before disconnecting the AC
power cord (mains lead), check
that the recorder’s hard disk is not
operating (recording or dubbing)
on the front panel display.
On placement
• Place the recorder in a location with
adequate ventilation to prevent heat
build-up in the recorder.
• Do not place the recorder on a soft
surface such as a rug that might
block the ventilation holes.
• Do not place the recorder in a
confined space such as a bookshelf
or similar unit.
• Do not place the recorder in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
• Do not place the recorder in an
inclined position. It is designed to
be operated in a horizontal
position only.
• Keep the recorder and discs away
from equipment with strong
magnets, such as microwave
ovens, or large loudspeakers.
• Do not place heavy objects on the
recorder.
On recording
• Note that the contents of the
recording cannot be compensated
for under any and all conditions,
including conditions that may
arise due to a malfunction of this
unit.
• Make trial recordings before
making the actual recording.
Copyrights
• Television programmes, films,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of such
material may be contrary to the
provisions of the copyright laws.
Also, use of this recorder with
cable television transmission may
require authorization from the
cable television transmitter and/or
programme owner.
• This product incorporates
copyright protection technology
that is protected by U.S. patents
and other intellectual property
rights. Use of this copyright
protection technology must be
authorized by Macrovision, and is
intended for home and other
limited viewing uses only unless
otherwise authorized by
Macrovision. Reverse engineering
or disassembly is prohibited.
Copy guard function
Since the recorder has a copy guard
function, programmes received
through an external tuner (not
supplied) may contain copy
protection signals (copy guard
function) and as such may not be
recordable, depending on the type of
signal.
IMPORTANT NOTICE
Caution: This recorder is capable
of holding a still video image or
on-screen display image on your
television screen indefinitely. If
you leave the still video image or
on-screen display image
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma display
panels and projection televisions
are especially susceptible to this.
If you have any questions or
problems concerning your recorder,
please consult your nearest Sony
dealer.
About this manual
• In this manual, the internal hard
disk drive is written as “HDD,”
and “disc” is used as a general
reference for the HDD, DVDs, or
CDs unless otherwise specified by
the text or illustrations.
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar names as
those on the remote.
• The on-screen display illustrations
used in this manual may not match
the graphics displayed on your TV
screen.
• The explanations regarding DVDs
in this manual refer to DVDs
created on this recorder. The
explanations do not apply to
DVDs that are created on other
recorders and played back on this
recorder.
3
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ways to Use Your DVD Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Quick Guide to Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recordable and playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Hookups and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 2: Connecting the Aerial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
About the SMARTLINK features (for SCART connections only) . . . . . . . . . . . . . . 15
Using the PROGRESSIVE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 5: Connecting the Mains Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Step 6: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Controlling TVs with the remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Controlling the volume of your AV amplifier (receiver) with the remote . . . . . . . . . 20
If you have a Sony DVD player or more than one Sony DVD recorder . . . . . . . . . 21
Step 7: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting a VCR or Similar Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting to the LINE 3/DECODER jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting to the LINE 2 IN or LINE 4 IN jacks . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting to a Satellite or Digital Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting a PAY-TV/Canal Plus Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connecting a decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Setting PAY-TV/Canal Plus channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Seven Basic Operations — Getting to Know Your DVD Recorder
1. Inserting and Formatting a DVD Disc (Disc Info) . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Inserting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Formatting a DVD disc (Disc Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2. Recording a Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Checking the disc status while recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3. Playing the Recorded Programme (Title List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4. Displaying the Playing Time and Play Information . . . . . . . . . . . . . . . . . . . . . . . . . 34
Checking the playing/remaining time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5. Changing the Name of a Recorded Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6. Labelling and Protecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Labelling a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Protecting a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7. Playing the Disc on Other DVD Equipment (Finalize) . . . . . . . . . . . . . . . . . . . . . . . 39
Unfinalizing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Recording mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Recording stereo and bilingual programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Unrecordable pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Timer Recording (Standard/VIDEO Plus+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Setting the timer manually (Standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Recording TV programmes using the VIDEO Plus+ system . . . . . . . . . . . . . . . . . 45
Using the Quick Timer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Adjusting the recording picture quality and size . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Creating chapters in a title. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Checking/Changing/Cancelling Timer Settings (Timer List) . . . . . . . . . . . . . . . . . . . . 47
Automatically erasing old titles (Auto Title Erase) . . . . . . . . . . . . . . . . . . . . . . . . . 49
Recording From Connected Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Recording from connected equipment with a timer (Synchro Rec) . . . . . . . . . . . . 49
Recording from connected equipment without a timer . . . . . . . . . . . . . . . . . . . . . 50
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Playback options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Adjusting the picture quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Adjusting the sound quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Pausing a TV Broadcast (TV Pause). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Playing from the beginning of the programme you are recording
(Chasing Playback) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Playing a previous recording while making another
(Simultaneous Rec and Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Searching for a Title/Chapter/Track, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Searching by Thumbnail (Visual Search) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Searching by title number or time code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Playing MP3 Audio Tracks or JPEG Image Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Selecting an MP3 album or track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Selecting a JPEG album or image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
About MP3 audio tracks and JPEG image files. . . . . . . . . . . . . . . . . . . . . . . . . . . 62
MP3 audio tracks or JPEG image files that the recorder can play . . . . . . . . . . . . 62
About playback order of albums, tracks, and files . . . . . . . . . . . . . . . . . . . . . . . . . 63
Erasing and Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Before Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Edit options for the HDD and DVD-RWs (VR mode). . . . . . . . . . . . . . . . . . . . . . . 64
Edit options for DVD+RWs/DVD-RWs (Video mode)/DVD+Rs/DVD-Rs. . . . . . . . 65
Erasing and Editing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Erasing a chapter (Delete Chapter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Erasing a section of a title (A-B Erase) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Erasing multiple titles (Erase Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Dividing a title (Divide). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Erasing all titles on the disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Erasing titles to open up disc space (Disc Map) . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Creating chapters manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
,continued
5
Creating and Editing a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Moving a Playlist title (Change Order) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Combining multiple Playlist titles (Combine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Dividing a Playlist title (Divide). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Dubbing (HDD y DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
About “Dub Mode” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Dubbing a single title (Title Dub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Dubbing multiple titles (Dub Selected Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Aerial Reception and Language Settings (Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Channel Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Channel List (Changing/Disabling the channels) . . . . . . . . . . . . . . . . . . . . . . . . . . 78
TV Guide Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Recording and Parental Control Settings (Features) . . . . . . . . . . . . . . . . . . . . . . . . . 85
Disc and Remote Control Settings/Factory Settings (Options) . . . . . . . . . . . . . . . . . . 87
Easy Setup
(Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Self-diagnosis Function
(When letters/numbers appear in the display) . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6
Ways to Use Your DVD Recorder
Recording/Playback
Compatible media and reference pages
Quick access to recorded titles
– Title List
,
Play the beginning of a title
while it is being recorded
– Chasing Playback
,
Watching one title while
recording another
– Simultaneous Rec and Play
,
Dubbing/Editing
HDD
+RW
-RWVR -RWVideo
+R
-R
“3. Playing the Recorded Programme (Title List)” on
page 32
HDD
-RWVR
“Playing from the beginning of the programme you are
recording (Chasing Playback)” on page 57
HDD
VCD
+RW
-RWVR -RWVideo
CD
DATA DVD DATA CD
+R
-R
“Playing a previous recording while making another
(Simultaneous Rec and Play)” on page 58
Compatible media and reference pages
Creating your own programme
– Playlist
,
Copying a recorded title to and
from the HDD
– Dubbing (HDD y DVD)
,
HDD
-RWVR
“Creating and Editing a Playlist” on page 69
HDD
+RW
-RWVR -RWVideo
+R
-R
“Dubbing (HDD y DVD)” on page 71
A list of recordable and playable discs is on page 8.
7
Quick Guide to Disc Types
Recordable and playable discs
Icon used in
this manual
Formatting
(new discs)
Compatibility with other DVD
players (finalizing)
Hard disk drive
(internal)
HDD
(Formatting
unnecessary)
Dub HDD contents to a DVD to
play on other DVD players
DVD+RW
+RW
Automatically
formatted in +VR
mode
Playable on DVD+RW
compatible players
(automatically finalized)
-RWVR
Format in VR mode
(page 29)
Playable only on VR mode
compatible players (finalization
unnecessary)
-RWVideo
Format in Video mode
(page 29)
Playable on most DVD players
(finalization necessary)
(page 39)
+R
Automatically
formatted
Playable on most DVD players
(finalization necessary)
(page 39)
-R
Automatically
formatted
Playable on most DVD players
(finalization necessary)
(page 39)
Type
Disc Logo
VR
mode
DVDRW
*2
Video
mode
DVD+R
DVD+R DL
DVD-R
Usable disc versions (as of March 2005)
• 8x-speed or slower DVD+RWs
• 6x-speed or slower DVD-RWs (Ver.1.1, Ver.1.2
with CPRM*1)
• 16x-speed or slower DVD+Rs
• 16x-speed or slower DVD-Rs (Ver.2.0, Ver.2.1)
• 2.4x-speed DVD+R DL (Double Layer) discs
8
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R DL,”
and “DVD-R” are trademarks.
*1
CPRM (Content Protection for Recordable Media) is
a coding technology that protects copyrights for
images.
*2
This logo applies to 4x and 6x speed DVD-RW discs.
Recording Features
Rewrite
(page 41)
Auto
Chapter
(page 85)
Editing Features
Manual
Chapter
(page 68)
Record
16:9 sizes
(page 46)
Change
title name
(page 65)
Delete
title
(page 67)
A-B Erase
(page 66)
Playlist
(page 69)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes*3
Yes
Yes
No
No
No
Yes
No
No
Yes
Yes*4
No
No
No
Yes
No
Yes*3
Yes
Yes*4
No
No
Discs that cannot be recorded on
• 8 cm discs
• DVD-Rs in VR mode (Video Recording format)
*3
Only if the recording mode is LSP, SP, HSP, or HQ,
and “DVD Rec. Picture Size” is set to “16:9.”
*4 Erasing titles does not free up disc space.
,continued
9
Playable discs
Type
Disc Logo
Icon used
in this
manual
DVD VIDEO
DVD
Discs such as movies that can be purchased or
rented
VIDEO CD
VCD
VIDEO CDs or CD-Rs/CD-RWs in VIDEO
CD/Super VIDEO CD format
CD
Music CDs or CD-Rs/CD-RWs in music CD
format that can be purchased
CD
DATA DVD
—
DATA DVD
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs/
DVD-ROMs containing JPEG image files
DATA CD
—
DATA CD
CD-ROMs/CD-Rs/CD-RWs containing MP3
audio tracks or JPEG image files
8 cm DVD+RW/
DVD-RW/DVD-R
—
—
“DVD VIDEO” and “CD” are trademarks.
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are not
recorded in music CD or Video CD format, or do
not contain MP3 or JPEG files
• Data part of CD-Extras
• DVD-ROMs that do not contain JPEG files or
are not in DVD Video format
• DVD Audio discs
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
(page 11)
• DVD-Rs recorded in VR mode (Video
Recording format)
10
Characteristics
8 cm DVD+RW, DVD-RW, and DVD-R
recorded with a DVD video camera.
(Still images recorded with a DVD video
camera cannot be played.)
Maximum recordable number of titles
Disc
Number of titles*
HDD
300
DVD-RW/DVD-R
99
DVD+RW/DVD+R
49
DVD+R DL
49
* The maximum length for each title is eight hours.
Note on playback operations of DVD VIDEOs/
VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by software
producers. Since this recorder plays DVD
VIDEOs/VIDEO CDs according to the disc
contents the software producers designed, some
playback features may not be available. Also, see
the instructions supplied with the DVD VIDEOs/
VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on the rear
of the unit and will only play DVD VIDEOs
(playback only) labelled with identical region
codes. This system is used to protect copyrights.
DVD VIDEOs labelled ALL will also play on this
recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region code.”
will appear on the TV screen. Depending on the
DVD VIDEO, no region code indication may be
labelled even though playing the DVD VIDEO is
prohibited by area restrictions.
X
RDR–XXXX
00V 00Hz
00W
NO.
0-000-000-00
Region code
Music discs encoded with copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please be
aware that among those discs, there are some that
do not conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
b Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or
CD-RWs/CD-Rs cannot be played on this recorder due
to the recording quality or physical condition of the
disc, or the characteristics of the recording device and
authoring software. The disc will not play if it has not
been correctly finalized. For more information, see the
operating instructions for the recording device.
• You cannot mix VR mode and Video mode on the same
DVD-RW. To change the disc’s format, reformat the
disc (page 29). Note that the disc’s contents will be
erased after reformatting.
• You cannot shorten the time required for recording
even with high-speed discs.
• It is recommended that you use discs with “For Video”
printed on their packaging.
• You cannot add new recordings to DVD+Rs, DVD-Rs,
or DVD-RWs (Video mode) that contain recordings
made on other DVD equipment.
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings made
on other DVD equipment. If you do add a new
recording, note that this recorder will rewrite the DVD
menu.
• You cannot edit recordings on DVD+RWs, DVD-RWs
(Video mode), DVD+Rs, or DVD-Rs that are made on
other DVD equipment.
• If the disc contains PC data unrecognizable by this
recorder, the data may be erased.
• You may not be able to record on some recordable
discs, depending on the disc.
11
Hookups and Settings
Hooking Up the Recorder
Follow steps 1 to 7 to hook up and adjust the settings of the recorder.
b Notes
•
•
•
•
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this recorder to a TV that does not have a SCART or video input jack.
Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (phono plug × 3 y phono plug × 3) (1)
• Mains lead (1)
• Aerial cable (1)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
12
Step 2: Connecting the Aerial Cable
Connect the aerial cable by following the steps below. Do not connect the mains lead until you reach
“Step 5: Connecting the Mains Lead” on page 18.
DVD recorder
LINE 1 - TV
LINE 3
Y
Hookups and Settings
to AERIAL IN
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
AERIAL
PB / CB
PR / CR
OPTICAL
LINE 4 IN
LINE 2 OUT
~ AC IN
COMPONENT
VIDEO OUT
IN
OUT
AERIAL
TV
to AERIAL OUT
Aerial cable (supplied)
: Signal flow
1
Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the
recorder.
2
Connect AERIAL OUT of the recorder to the aerial input of your TV, using the supplied aerial
cable.
13
Step 3: Connecting the Video Cords
Select one of the following patterns A through D, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver). This will enable you to view pictures.
A Connecting to a SCART input jack
When you set “Line1 Output” to “S Video” or “RGB” in “Easy Setup” (page 22), use a SCART cord that
conforms to the selected signal.
B Connecting to a video input jack
You will enjoy standard quality images.
C Connecting to an S VIDEO input jack
You will enjoy high quality images.
D Connecting to component video input jacks (Y, PB/CB, PR/CR)
You will enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, you must use this connection and set
“Component Out” in “Video” setup to “On” (page 81). Then press PROGRESSIVE on the remote to send
progressive video signals. For details, see “Using the PROGRESSIVE button” on page 16.
B
S-video cord
(not supplied)
INPUT
Audio/video
cord (supplied)
VIDEO
INPUT
S VIDEO
C
L
AUDIO
TV, projector, or AV
amplifier (receiver)
(yellow)
R
TV, projector, or AV
amplifier (receiver)
to LINE 2 OUT (VIDEO)
LINE 1 - TV
to LINE 2 OUT (S VIDEO)
DVD recorder
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
PB / CB
S VIDEO
DIGITAL OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
AERIAL
PR / C R
OPTICAL
LINE 4 IN
To i LINE 1 – TV
LINE 2 OUT
(red)
~ AC IN
COMPONENT
VIDEO OUT
(blue)
(green)
SCART cord (not supplied)
COMPONENT
VIDEO IN
Y
A
Component video
cord (not supplied)
TV
: Signal flow
14
to COMPONENT
VIDEO OUT
D
(green)
PB/CB
(blue)
PR/CR
(red)
TV, projector, or AV
amplifier (receiver)
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the picture size, see page 81.
If you are connecting to a VCR
b Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same time.
• You cannot use the PROGRESSIVE button with the
connections B and C.
• When you connect the recorder to your TV via the
SCART jacks, the TV’s input source is set to the
recorder automatically when you start playback. If
necessary, press t TV/VIDEO to return the input to
the TV.
• For correct SMARTLINK connection, you will need a
SCART cord that has the full 21 pins. Refer to your
TV’s instruction manual as well for this connection.
• If you connect this recorder to a TV with
SMARTLINK, set “Line1 Output” to “Video” in “Easy
Setup.”
*1
About the SMARTLINK features
(for SCART connections only)
If the connected TV (or other connected
equipment such as a set top box) complies with
SMARTLINK, NexTView Link*3,
MEGALOGIC*1, EASYLINK*2,
CINEMALINK*2, Q-Link*3, EURO VIEW
LINK*4, or T-V LINK*5, this recorder
automatically runs the SMARTLINK function
after you complete the connection pattern A on
page 14 (the SMARTLINK indicator lights up
when you turn on your TV). You can enjoy the
following SMARTLINK features.
• Preset Download
You can download the tuner preset data from
your TV to this recorder, and tune the recorder
according to that data in “Easy Setup.” This
greatly simplifies the “Easy Setup” procedure.
Be careful not to disconnect the cables or exit the
“Easy Setup” function during this procedure
(page 22).
• TV Direct Rec
You can easily record what you are watching on
your TV (page 31).
*2
*3
*4
*5
Hookups and Settings
Connect your VCR to the LINE 3/DECODER
jack on the recorder (page 23).
• One Touch Play
You can turn on the recorder and TV, set the
TV’s input to the recorder, and start playback
with one touch of the H (play) button
(page 53).
• One Touch Menu
You can turn on the recorder and TV, set the TV
to the recorder’s channel, and display the Title
List menu with one touch of the TITLE LIST
button (page 53).
• One Touch Timer
You can turn on the recorder and TV, set the TV
to the recorder’s channel, and display the timer
programming menu with one touch of the
[TIMER] button (page 44).
• Automatic Power Off
The recorder will turn off automatically if the
recorder is not used after you turn off the TV.
• NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
See your TV’s instruction manual.
“MEGALOGIC” is a registered trademark of Grundig
Corporation.
“EASYLINK” and “CINEMALINK” are trademarks
of Philips Corporation.
“Q-Link” and “NexTView Link” are trademarks of
Panasonic Corporation.
“EURO VIEW LINK” is a trademark of Toshiba
Corporation.
“T-V LINK” is a trademark of JVC Corporation.
z Hint
SMARTLINK also works with TVs or other equipment
having EPG Timer Control, EPG Title Download, and
Now Recording functions. For details, refer to the
operating instructions supplied with your TV or other
equipment.
b Notes
• The SMARTLINK features are available only when
“Video” is selected in “Line1 Output.”
• Not all TVs respond to the functions above.
,continued
15
Using the PROGRESSIVE button
By using the PROGRESSIVE button, you can
select the signal format in which the recorder
outputs video signals: interlace or progressive.
1
Connect the recorder using the
COMPONENT VIDEO OUT jacks (pattern
D on page 14).
2
Set “Component Out” in “Video” setup to
“On” (page 81).
3
Press the PROGRESSIVE button.
“PROGRESSIVE” appears in the front panel
display when the recorder outputs progressive
signals.
Progressive
Select this when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT
VIDEO OUT jacks.
Note that the pictures will not be clear or no
picture will appear if you select progressive signal
output when either of the above conditions is not
met.
Interlace
Set to this position when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the
COMPONENT VIDEO OUT jacks (LINE 2
OUT (VIDEO or S VIDEO)).
z Hint
When you select progressive signal output, you can finetune the signal according to the type of software you are
watching (page 82).
b Note
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In the
case of 525/625 progressive scan picture problems, it is
recommended that the user switch the connection to the
‘standard definition’ output. If there are questions
regarding our TV set compatibility with this model 525p/
625p DVD recorder, please contact our customer service
centre.
16
Step 4: Connecting the Audio Cords
Select one of the following patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver). This will enable you to listen to sound.
This connection will use your TV’s or stereo amplifier’s (receiver’s) two speakers for sound. You can
enjoy the following surround effects (page 54).
• TV: Dynamic, Wide, Night
• Stereo amplifier (receiver): Standard, Night
B Connecting to a digital audio input jack
Hookups and Settings
A Connecting to audio L/R input jacks
If your AV amplifier (receiver) has a Dolby*1 Digital, DTS*2, or MPEG audio decoder and a digital input
jack, use this connection. You can enjoy Dolby Digital (5.1ch), DTS (5.1ch), and MPEG audio (5.1ch)
surround effects.
(yellow)
(red)
Audio/video
cord (supplied)
A
INPUT
VIDEO
(white)
(white)
L
(red)
(yellow)*
AUDIO
R
R-AUDIO-L
VIDEO
S VIDEO
TV, projector, or AV
amplifier (receiver)
LINE 2 OUT
to LINE 2 OUT (R-AUDIO-L)
LINE 1 - TV
DVD recorder
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
PB / CB
S VIDEO
DIGITAL OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
AERIAL
PR / C R
OPTICAL
LINE 4 IN
~ AC IN
COMPONENT
VIDEO OUT
LINE 2 OUT
to DIGITAL OUT (COAXIAL or OPTICAL)
COAXIAL
or
DIGITAL OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
OPTICAL
Coaxial digital cord (not supplied)
Optical digital cord (not supplied)
[Speakers]
to optical
digital input
to coaxial
digital input
Rear (L)
Front (L)
[Speakers]
B
Rear (R)
AV amplifier (receiver)
with a decoder
Centre
Front (R)
Subwoofer
: Signal flow
* The yellow plug is used for video signals (page 14).
,continued
17
z Hint
For correct speaker location, see the operating
instructions supplied with the connected components.
b Notes
• Do not connect your TV’s audio output jacks to the
LINE IN (R-AUDIO-L) jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.
• In the connection A, do not connect the LINE IN (RAUDIO-L) and LINE 2 OUT (R-AUDIO-L) jacks to
your TV’s audio output jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.
• In the connection B, after you have completed the
connection, make the appropriate settings under
“Audio Connection” in “Easy Setup” (page 22).
Otherwise, no sound or a loud noise will come from
your speakers.
• With the connection B, the surround sound effects of
this recorder cannot be used.
Step 5: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the recorder
and TV mains leads (power cords) into the mains.
After you connect the mains lead, you must wait
for a short while before operating the
recorder. You can operate the recorder once the
front panel display lights up and the recorder
enters standby mode.
If you connect additional equipment to this
recorder (page 23), be sure to connect the mains
lead after all connections are complete.
*1 Manufactured
under license from Dolby Laboratories.
“Dolby,” and the double-D symbol are trademarks of
Dolby Laboratories.
*2 “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
~ AC IN
1
to AC IN
2
to mains
18
Step 6: Preparing the
Remote
You can adjust the remote’s signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.
b Notes
• Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
Hookups and Settings
You can control the recorder using the supplied
remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the
markings inside the battery compartment. When
using the remote, point it at the remote sensor
on the recorder.
Controlling TVs with the remote
TV/DVD switch
[/1
Number
buttons, SET,
-/--
1
2
3
4
5
6
7
8
9
PROG +/–
2 +/–
0
b Notes
• If the supplied remote interferes your other Sony DVD
recorder or player, change the command mode number
for this recorder (page 21).
• Use the batteries correctly to avoid possible leakage
and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an extended
period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid inside
the battery compartment, and insert new batteries.
• Do not expose the remote sensor (marked
on the
front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.
t TV/VIDEO
1
2
3
Slide the TV/DVD switch to TV.
Hold down [/1.
Enter your TV’s manufacturer code (see
“Code numbers of controllable TVs”
below) using the number buttons.
,continued
19
4
Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
Buttons
Operations
[/1
Turns your TV on or off
2 (volume) +/–
Adjusts the volume of
your TV
Manufacturer
Code number
Philips
06, 07, 08, 23, 45, 72
Saba
12, 13, 36, 43, 74, 75
Samsung
06, 22, 23, 71, 72
Sanyo
25
Sharp
29
Telefunken
12, 13, 36, 43, 74, 75
Thomson
12, 13, 43, 74, 75
Switches to or from the
wide mode of a Sony
wide-screen TV
Toshiba
38
LG
06
t TV/VIDEO
Switches your TV’s
input source
JVC
33
Number buttons
and SET, -/--*
Selects the programme
position on your TV
PROG +/–
(wide mode)
Selects the programme
position on your TV
* If you use the number buttons to select the TV’s
programme position, press -/-- followed by the
number buttons for two-digit numbers.
Controlling the volume of your AV
amplifier (receiver) with the
remote
TV/DVD
switch
To operate the t TV/VIDEO button
(for SCART connections only)
The t TV/VIDEO button switches between the
recorder and the last input source selected on the
TV. Point your remote at the recorder when using
this button. The button works even if the TV/DVD
switch is set to DVD.
When you connect the recorder to the TV via the
SCART jacks, the input source for the TV is set to
the recorder automatically when you start
playback. To watch another source, press the
t TV/VIDEO button to switch the TV’s input
source.
[/1
Number buttons
20
Manufacturer
Code number
Sony
01 (default)
Aiwa
01 (default)
Grundig
11
Hitachi
23, 24, 72
Loewe
06, 45
Nokia
15, 16, 69, 73
Panasonic
17, 49
2
3
4
5
6
7
8
9
0
2 +/–
1
2
Slide the TV/DVD switch to DVD.
3
Release [/1.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
1
Hold down [/1, and enter the
manufacturer code (see the table below)
for your AV amplifier (receiver) using the
number buttons.
The 2 (volume) +/– buttons control the AV
amplifier’s volume.
If you want to control the TV’s volume, slide
the TV/DVD switch to TV.
z Hint
If you want to control the TV’s volume even when the
TV/DVD switch is set to DVD, repeat the steps above
and enter the code number 90 (default).
Code numbers of controllable AV amplifiers
(receivers)
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your AV amplifier (receiver).
Press SYSTEM MENU.
The System Menu appears.
2
Select “SETUP,” and press ENTER.
SETUP
Code number
Settings
Channel Setting
Video
Channel List
Audio
TV Guide Page
Features
Clock
84, 85, 86
Options
Language
Kenwood
92, 93
Easy Setup
Onkyo
81, 82, 83
Sony
78, 79, 80, 91
Denon
Pioneer
99
Sansui
87
Technics
97, 98
Yamaha
94, 95, 96
3
Select “Options,” and press ENTER.
Hookups and Settings
Manufacturer
1
SETUP
If you have a Sony DVD player or
more than one Sony DVD recorder
If the supplied remote interferes with your other
Sony DVD recorder or player, set the command
mode number for this recorder and the supplied
remote to one that differs from the other Sony
DVD recorder or player.
The default command mode setting for this
recorder and the supplied remote is DVD3.
Settings
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Normal
Options
Power Save :
Off
Auto Display :
On
Command Mode :
DVD3
Easy Setup
Factory Setup
4
Select “Command Mode,” and press
ENTER.
SETUP
Settings
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Options
Power Save :
Easy Setup
1
2
3
4
5
6
7
8
9
0
SYSTEM
MENU
M/m,
ENTER
O RETURN
Normal
Command Mode :
Off
DVD1
On
DVD2
DVD3
Factory Setup
DVD3
Auto Display :
5
Select the Command mode (DVD1, DVD2,
or DVD3), and press ENTER.
6
Slide the COMMAND MODE switch on the
remote so it matches the mode you
selected above.
To return to the previous step
Press O RETURN.
COMMAND
MODE
switch
Check that the command mode switch on the
remote is set to the default setting of DVD3
before you try to change the command mode for
the recorder. If the command mode for the remote
is changed to DVD1 or DVD2, you may be
unable to operate this recorder.
21
TV Type
If you have a wide-screen TV, select “16:9.”
If you have a standard TV, select either “4:3
Letter Box” (shrink to fit) or “4:3 Pan Scan”
(stretch to fit). This will determine how
“wide-screen” images are displayed on your
TV.
Step 7: Easy Setup
Make the basic adjustments by following the
on-screen instructions in “Easy Setup.”
Component Out
If you are using the COMPONENT VIDEO
OUT jack, select “On.”
[/1
1
2
3
4
5
6
7
8
9
PROG +/–
Line3 Input
If you will connect a decoder to the LINE 3/
DECODER jack, select “Yes.”
0
Line1 Output
To output video signals, select “Video.”
To output S video signals, select “S Video.”
To output RGB signals, select “RGB.”
Select “Video” to enjoy the SMARTLINK
features.
• If you set “Component Out” to “On,” you
cannot select “RGB.”
If you set “Line3 Input” to “Yes,” you
cannot select “S Video.”
</M/m/,,
ENTER
O RETURN
1
Turn on the recorder and switch the input
selector on your TV so that the signal from
the recorder appears on your TV screen.
The message about the initial settings appears.
• If this message does not appear, select “Easy
Setup” from “SETUP” in the System Menu
to run “Easy Setup” function (“Settings and
Adjustments” on page 76).
2
3
Press ENTER when “Finish” appears.
“Easy Setup” is finished.
Press ENTER.
Follow the on-screen instructions to make the
following settings.
OSD
Select the language for the on-screen displays.
Tuner System
Select your country or language.
The programme position order will be set
according to the country you set.
To set the programme positions manually, see
page 76.
• If you live in a French speaking country that
is not listed on the display, select “ELSE.”
Clock
The recorder will automatically search for a
clock signal. If a clock signal cannot be found,
set the clock manually using </M/m/,, and
press ENTER.
22
Audio Connection
If you connected an AV amplifier (receiver)
using either a digital optical or coaxial cord,
select “Yes: DIGITAL OUT” and set the
digital output signal (page 84).
To return to the previous step
Press O RETURN.
z Hints
• If your AV amplifier (receiver) has an MPEG audio
decoder, set “MPEG” to “MPEG” (page 84).
• If you want to run “Easy Setup” again, select “Easy
Setup” from “SETUP” in the System Menu (page 88).
Connecting a VCR or Similar Device
Connecting to the LINE 3/DECODER jack
Connect a VCR or similar recording device to the LINE 3/DECODER jack of this recorder.
TV
Hookups and Settings
After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar recording device
to the LINE IN jacks of this recorder.
See also the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording from connected equipment without a timer” on page 50.
VCR
SCART cord (not supplied)
to SCART input
to i LINE 3/DECODER
to i LINE 1 – TV
LINE 1 - TV
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
AERIAL
PCM/DTS/MPEG/
DOLBY DIGITAL
PB / CB
PR / CR
OPTICAL
LINE 4 IN
LINE 2 OUT
~ AC IN
COMPONENT
VIDEO OUT
DVD recorder
b Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen.
DVD recorder
VCR
TV
Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes,
watch the tapes through a second line input on your TV.
Line input 1
VCR
DVD recorder
TV
Line input 2
• The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3/DECODER jack.
• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the t TV/
VIDEO button on the remote.
• If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected VCR.
,continued
23
Connecting to the LINE 2 IN or LINE 4 IN jacks
Connect a VCR or similar recording device to the LINE 2 IN or LINE 4 IN jacks of this recorder. If the
equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
OUTPUT
VIDEO
S VIDEO
AUDIO
L
R
Audio/video cord
(not supplied)
S-video cord
(not supplied)
to LINE 2 IN
DVD recorder (front)
(rear)
LINE 1 - TV
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
AERIAL
PCM/DTS/MPEG/
DOLBY DIGITAL
PB / CB
PR / CR
OPTICAL
LINE 4 IN
LINE 2 OUT
~ AC IN
COMPONENT
VIDEO OUT
to LINE 4 IN
VCR, etc.
: Signal flow
z Hint
When the connected equipment outputs only monaural sound, use audio cables that distribute monaural sounds to left/
right channels (not supplied).
b Notes
• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
• Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output
jack connected to the input jack of this recorder. Noise (feedback) may result.
• Do not connect more than one type of video cord between the recorder and your TV at the same time.
24
Connecting to a Satellite or Digital Tuner
TV
to SCART input
Hookups and Settings
Connect a satellite or digital tuner to this recorder using the LINE 3/DECODER jack. Disconnect the
recorder’s mains lead from the mains when connecting the tuner.
To use the Synchro-Rec function, see below.
Satellite tuner, etc.
SCART cord
(not supplied)
to i LINE 1 – TV
to i LINE 3/DECODER
LINE 1 - TV
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
AERIAL
PCM/DTS/MPEG/
DOLBY DIGITAL
PB / CB
PR / CR
OPTICAL
LINE 4 IN
LINE 2 OUT
~ AC IN
COMPONENT
VIDEO OUT
DVD recorder
If the satellite tuner can output RGB signals
This recorder accepts RGB signals. If the satellite
tuner can output RGB signals, connect the TV
SCART connector on the satellite tuner to the
LINE 3/DECODER jack, and set “Line3 Input” of
“Scart Setting” to “Video/RGB” in “Video” setup
(page 82). Note that this connection and setup
disable the SMARTLINK function. If you want to
use the SMARTLINK function with a compatible
set top box, see the instructions supplied with the
set top box.
If you want to use the Synchro Rec function
This connection is necessary to use the SynchroRecording function. See “Recording from
connected equipment with a timer (Synchro Rec)”
on page 49.
Set “Line3 Input” of “Scart Setting” in “Video”
setup (page 82) according to the specifications of
your satellite tuner. See your satellite tuner’s
instructions for more information.
If you are using a B Sky B tuner, be sure to
connect the tuner’s VCR SCART jack to the LINE
3/DECODER jack. Then set “Line3 Input” of
“Scart Setting” according to the specifications of
the VCR SCART jack on your satellite tuner.
b Notes
• Do not set “Line3 Input” of “Scart Setting” in “Video”
setup to “Decoder.”
• Synchronized Recording does not work with some
tuners. For details, see the tuner’s operating
instructions.
• If you disconnect the recorder’s mains lead, you will
not be able to view the signals from the connected
tuner.
25
Connecting a PAY-TV/Canal Plus Decoder
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder (not supplied) to the
recorder. Disconnect the recorder’s mains lead from the mains when connecting the decoder.
Connecting a decoder
TV
Aerial cable
(supplied)
to AERIAL IN
to SCART input
PAY-TV/Canal Plus
decoder
SCART cord
(not supplied)
SCART cord (not supplied)
to i LINE 1 – TV
to AERIAL OUT
to i LINE 3/DECODER
DVD recorder
LINE 1 - TV
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
AERIAL
PCM/DTS/MPEG/
DOLBY DIGITAL
LINE 4 IN
26
PB / CB
PR / CR
OPTICAL
LINE 2 OUT
COMPONENT
VIDEO OUT
~ AC IN
Setting PAY-TV/Canal Plus
channels
1
2
3
4
5
6
7
8
9
PROG +/–
Select “Scart Setting,” and press ENTER.
Video - Scart Setting
5
Line1 Output
Line3 Input
Video
Video/RGB
Video
Video
Video/RGB
Line3 Output
S Video
Video
Decoder
Video
S Video
S Video
Video
S Video
S Video
S Video
RGB
Video/RGB
Video
Press M/m to select “Video” or “RGB” for
“Line1 Output,” “Decoder” for “Line3
Input,” and “Video” for “Line3 Output,”
and press ENTER.
The “Video” setup display appears again.
6
Press O RETURN to return the cursor to
the left column.
7
Select “Settings,” and press ENTER.
0
SYSTEM
MENU
Hookups and Settings
To watch or record PAY-TV/Canal Plus
programmes, set your recorder to receive the
channels using the on-screen display.
In order to set the channels correctly, be sure to
follow all of the steps below.
4
SETUP
</M/m/,,
ENTER
O RETURN
Settings
Channel Setting
Video
Channel List
Audio
TV Guide Page
Features
Clock
Options
Language
Easy Setup
1
Press SYSTEM MENU.
The System Menu appears.
2
8
Select “SETUP,” and press ENTER.
Settings - Channel Setting
SETUP
System :
BG
Normal / CATV :
Normal
Channel Set :
C2
Settings
Channel Setting
Station Name :
CDE
Video
Channel List
PAY - TV / CANAL+ :
Off
Audio
TV Guide Page
Audio :
NICAM
Features
Clock
Options
Language
9
Easy Setup
3
Select “Channel Setting,” and press
ENTER.
Prog. 8
Press PROG +/– to select the desired
programme position.
Selected programme position
Select “Video,” and press ENTER.
Settings - Channel Setting
SETUP
System :
BG
Normal / CATV :
Normal
Settings
TV Type :
16 : 9
Channel Set :
C24
Video
Pause Mode :
Auto
Station Name :
PQR
Audio
Component Out :
Off
PAY - TV / CANAL+ :
Off
Features
Progressive Mode :
Auto
Audio :
NICAM
Options
Scart Setting
Line4 Input :
Prog. 6
Video
Easy Setup
,continued
27
10 Select “System,” and press ENTER.
Settings - Channel Setting
System :
BG
BG
Normal / CATV :
Normal
DK
Channel Set :
C
I2
Station Name :
CDE
L
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 6
11 Press M/m to select an available TV
system, BG, DK, I, or L, and press ENTER.
To receive broadcasts in France, select “L.”
12 Select “Normal/CATV,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Normal
Channel Set :
2
C
CATV
Station Name :
PQR
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 6
13 Select “Normal,” and press ENTER.
To preset CATV (Cable Television) channels,
select “CATV.”
14 Select “Channel Set,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
2
C
C24
Station Name :
PQR
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 6
15 Select the PAY-TV/Canal Plus channel,
and press ENTER.
16 Select “PAY-TV/CANAL+,” and press
ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
C24
Station Name :
PQR
PAY - TV / CANAL+ :
Off
On
Audio :
NICAM
Off
Prog. 6
17 Select “On,” and press ENTER.
28
To return to the previous step
Press O RETURN.
b Notes
• When you set “Line3 Input” to “Decoder” in step 5
above, you will not be able to select “L3” because Line
3 will become a dedicated line for the decoder.
• If you disconnect the recorder’s mains lead, you will
not be able to view the signals from the connected
decoder.
Formatting a DVD disc (Disc Info)
Seven Basic Operations
— Getting to Know Your DVD Recorder
+RW
1. Inserting and Formatting
a DVD Disc (Disc Info)
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
New discs are automatically formatted when
inserted. If necessary, you can manually re-format
a DVD+RW or DVD-RW disc to make a blank
disc. For DVD-RWs, you can select a recording
format (VR mode or Video mode) according to
your needs (page 8).
-R
DATA DVD DATA CD
Z
DVD
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
0
0
</M/m/,,
ENTER
1
2
TOOLS
Press DVD.
Press Z (open/close), and place a disc on
the disc tray.
1
Insert a disc.
See “Inserting a Disc” on page 29.
2
Seven Basic Operations — Getting to Know Your DVD Recorder
Inserting a Disc
-RWVR -RWVideo
Press TOOLS.
The TOOLS menu appears.
Close
With the recording/playing side facing down
Stop
Erase
Protect
3
Press Z (open/close) to close the disc
tray.
Wait until “LOAD” disappears from the front
panel display.
Unused DVDs are formatted automatically.
Dubbing
Options for the disc or picture
The TOOLS menu displays options
applicable to the entire disc (e.g. disc
protection), recorder (e.g. audio settings
during recording), or multiple items on a list
menu (e.g. erasing multiple titles). The
displayed options differ depending on the
situation and disc type.
,continued
29
3
Move the cursor down the TOOLS menu
until “Disc Info” is selected, and press
ENTER.
Example: When a DVD-RW (VR mode) is
inserted.
Disc Information
Close
DiscName Movie
Disc Name
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Format
2. 3 / 4. 7GB
1 “Disc Name” (DVD only)
2 “Media”: Disc type
3 “Format”: Recording format type (DVDRW only)
4 “On”/“Off”: Indicates whether
protection is set (DVD-RW in VR mode
only)
5 “Title no.”: Total number of titles
6 “Date”: Dates of when the oldest and the
most recent titles were recorded (DVD
only)
7 “Continuous Rem. Time”/“Remainder”
(approximate)
• The remaining recording time in each of the
recording modes
• Disc space bar
• Remaining disc space/total disc space
8 Disc setting buttons
“Disc Name” (page 38)
“Protect Disc” (page 38)
“Finalize”/“Unfinalize” (page 39)
“Erase All” (page 68)
“Format”
Available settings differ depending on the
disc type.
4
5
Select “Format,” and press ENTER.
Select “OK,” and press ENTER.
For DVD-RWs, select “VR” or “Video,” and
press ENTER.
All contents on the disc are erased.
30
z Hints
• By reformatting, you can change the recording format
on DVD-RWs, or record again on DVD-RWs that have
been finalized.
• For DVD+RWs and DVD-RWs (Video mode), you can
check free space and title location on the disc using the
Disc Map display (page 68).
b Note
On this model, 1 GB (read “gigabyte”) is equivalent to 1
billion bytes. The larger the number, the larger the disc
space.
2. Recording a Programme
HDD
+RW
-RWVR -RWVideo
+R
-R
HDD
Press z REC.
Recording starts.
Recording stops automatically after 8 hours of
continuous recording or when the HDD or
DVD is full.
To stop recording
Press x REC STOP located beneath the remote
control cover.
Note that it may take a few seconds for recorder to
stop recording.
DVD
1
2
3
4
5
6
7
8
9
PROG +/–
0
t TV/VIDEO
DISPLAY
To pause recording
Press X REC PAUSE located beneath the remote
control cover.
To restart recording, press the button again.
To watch another TV programme while
recording
X REC PAUSE
x REC STOP
z REC
REC MODE
1
If your TV is connected to the LINE 1 – TV jack,
set your TV to the TV input using the t TV/
VIDEO button and select the programme you
want to watch. If your TV is connected to the
LINE OUT or COMPONENT VIDEO OUT
jacks, set the TV to TV input using the t TV/
VIDEO button (page 19).
TV Direct Rec
Press HDD or DVD.
When you record to a DVD, insert a
recordable DVD (see “Inserting a Disc” on
page 29).
2
Press PROG +/– to select the programme
position or input source you want to
record.
3
Press REC MODE repeatedly to select the
recording mode.
If you use the SMARTLINK connection, you can
easily record what you are watching on your TV.
When the TV is turned on or in standby mode,
press z REC. The recorder automatically turns on
and starts recording what you are watching on the
TV.
Seven Basic Operations — Getting to Know Your DVD Recorder
This section introduces the basic operation to
record the current TV programme to the hard disk
(HDD) or to a disc (DVD). For an explanation of
how to make timer recordings, see page 41.
4
b Note
If “TV” appears in the front panel display, you
cannot turn off the TV or change the programme
position during TV Direct Rec. To turn off the
function, set “TV Direct Rec” to “Off” in
“Features” setup (page 85).
Each time you press the button, the display on
the TV screen changes as follows:
HQ
HSP
SP
LSP
LP
SEP
SLP
EP
For more details about the recording mode,
see page 41.
,continued
31
About the Teletext function
Some broadcasts systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time
etc.) are stored day by day. When recording a
programme, the recorder automatically takes the
programme name from the Teletext pages and
stores it as the title name. For detail, see “TV
Guide Page” on page 79.
Note that the Teletext information will not appear
on your TV screen. To view the Teletext
information on your TV screen, press t TV/
VIDEO on the remote to switch the input source to
your TV.
3. Playing the Recorded
Programme (Title List)
HDD
+RW
-RWVR -RWVideo
HDD
DVD
1
2
3
4
5
6
7
8
9
0
z Hint
If you do not want to watch TV while recording, you can
turn off the TV. When using a decoder, make sure to
leave it on.
TITLE LIST
M/m,
ENTER
b Notes
• After pressing z REC, it may take a short while to
start recording.
• You cannot change the recording mode while
recording or during recording pause.
• If there is a power failure, the programme you are
recording may be erased.
• You cannot watch a PAY-TV/Canal Plus programme
while recording another PAY-TV/Canal Plus
programme.
• To use the TV Direct Rec function, you must first set
the recorder’s clock correctly.
You can check the recording information such as
recording time or disc type.
Press DISPLAY twice during recording.
The recording information appears.
A Disc type/format
B Recording status
C Recording mode
D Recording time
Press DISPLAY to turn off the display.
32
-R
To play a recorded title, select the title from the
Title List.
* not available in some areas
Checking the disc status while
recording
+R
TOOLS
/
m
1
M
H/X/x
Press HDD or DVD.
If you select DVD, insert a DVD (see
“Inserting a Disc” on page 29).
Playback starts automatically depending on
the disc.
2
Press TITLE LIST.
To show the extended Title List, press
TOOLS to select “Display List,” and press
ENTER.
Title List with Thumbnail Images (Example:
DVD-RW in VR mode)
TITLE LIST
ORIGINAL
3
The sub-menu appears.
The sub-menu displays options applicable
only to selected item. The displayed options
differ depending on the model, situation, and
disc type.
4.3 / 4.7GB
12 Tennis
Fri 28.10. 2005 13:00
Select a title, and press ENTER.
AAB
(0H30M) LSP 0.9GB
11 Travel
DEF
Wed 26.10. 2005 20:00 (0H30M) SEP 0.3GB
10 Mystery
Tue 25.10. 2005 9:00
TITLE LIST
AAB
(1H00M) SLP 0.8GB
ORIGINAL
12 Tennis
9 World Sports
Fri 28.10. 2005 13:00
11 Travel
Play Beginning
Erase
DEF
SEP 0.3GB
Wed 26.10. 2005 20:00 (0H30M)
Protect
m
10 Mystery
Tue 25.10. 2005 9:00
Extended Title List
TITLE LIST
4.3 / 4.7GB
Close
AAB
Play LSP 0.9GB
(0H30M)
9 World Sports
Dubbing
AAB
Visual Search
(1H00M)
SLP 0.8GB
Title Name
Delete Chapter GHI
SEP 0.6GB
Wed 19.10. 2005 20:00 (1H00M)
A-B Erase
ORIGINAL
4.3 / 4.7GB
12
Tennis
AAB Fri
11
Travel
DEF Wed 26.10
10
Sub-menu
28.10
25.10
Mystery
AAB Tue
9
World Sports
GHI
8
Family
DEF Mon
7
Nature
L3
Sat
15.10
6
News
GHI
Fri
14.10
5
Weather
L3
Thu
13.10
Wed 19.10
17.10
4
Select “Play,” and press ENTER.
Playback starts from the selected title.
To stop playback
Press x.
A Disc type:
Displays a media type, HDD or DVD.
Also displays the title type (Original or
Playlist) for DVD-RWs (VR mode).
B Disc space (remainder/total)
C Title information:
Displays the title number, title name, and
recording date. Title size is shown in the
Thumbnail title list.
z (red): Indicates that the title is currently
being recorded.
: Indicates that the title is currently being
dubbed.
: Indicates the protected title.
“NEW” (or N): Indicates that the title is newly
recorded (not played back) (HDD only).
: Indicates that the Update function is set
(HDD only) (page 43).
: Indicates titles containing “CopyOnce” copy protection signals (HDD only)
(page 72).
D Scroll bar:
Appears when all of the titles do not fit on the
list. To view the hidden titles, press M/m.
E Title’s thumbnail picture
The still images for each title are displayed.
To scroll the list display by page (Page mode)
Press
/
while the list display is turned on.
Each time you press
/
, the entire Title List
changes to the next/previous page of titles.
About the Title List for HDD/DVD-RWs (VR
mode)
Seven Basic Operations — Getting to Know Your DVD Recorder
GHI
Wed 19.10. 2005 20:00 (1H00M) SEP 0.6GB
You can switch the Title List to show Original or
Playlist.
While the Title List menu is turned on, press
TOOLS to select either “Original” or “Playlist,”
and press ENTER.
For details, see “Edit options for the HDD and
DVD-RWs (VR mode)” on page 64.
To change the title order (Sort)
While the Title List menu is turned on, press
TOOLS to select “Sort Titles.” Press M/m to select
the item, and press ENTER.
Order
Sorted
By Date
in order of when the titles were
recorded. The title that is recorded
most recently is listed at the top.
By Title
in alphabetical order.
By Number
in order of recorded title number.
,continued
33
Order
Sorted
Unseen Title
(HDD only)
in order of when the titles were
recorded. The title that is recorded
most recently and not played back
is listed at the top. Playlist titles
are not displayed.
To change a title thumbnail picture
(Thumbnail) (HDD/DVD-RW in VR mode only)
You can select a favourite scene for the thumbnail
picture shown in the Title List menu.
1
2
3
4
5
4. Displaying the Playing
Time and Play Information
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
DATA DVD DATA CD
You can check the playing time and remaining
time of the current title, chapter, or track. Also,
you can check the disc name recorded on the
DVD/CD.
Press TITLE LIST in stop mode.
Select a title whose thumbnail picture you
want to change, and press ENTER.
The sub-menu appears.
Select “Set Thumbnail,” and press ENTER.
The selected title starts to play in the
background.
While watching the playback picture, press
H, X, or m/M to select the scene you
want to set for a thumbnail picture, and press
ENTER.
The display asks for confirmation.
Select “OK,” and press ENTER.
The scene is set for the title’s thumbnail
picture.
To turn off the Title List
Press TITLE LIST.
z Hints
• After recording, the first scene of the recording (the
title) is automatically set as the thumbnail picture.
• You can selelct “TITLE LIST” from the System Menu.
1
2
3
4
5
6
7
8
9
0
DISPLAY
TIME/TEXT
Press DISPLAY repeatedly.
Each time you press the button, the display
changes as follows:
Display 1 t Display 2 t Display off
The displays differ depending on the disc type or
playing status.
Display 1
Example: When playing a DVD VIDEO
Title 1
Angle3(5)
1 : English DolbyDigital 2/0
b Notes
• The title names may not appear for DVDs created on
other DVD recorders.
• The letters that cannot be displayed are replaced with
“*.”
• It may take a few seconds for the thumbnail pictures to
be displayed.
• After editing, the title thumbnail picture may change to
the first scene of the recording (title).
• After dubbing, the title thumbnail picture set on the
source recording is cancelled.
34
A Title number/name
(Shows either track number, track name,
scene number, or file name for CDs, VIDEO
CDs, DATA DVDs, or DATA CDs.)
B Available functions for DVD VIDEOs
(
angle/
audio/
subtitle, etc.),
or playback data for DATA DVDs and
DATA CDs
C The current selected function or audio
setting (appears only temporarily)
Example: Dolby Digital 5.1 ch
Rear (L/R)
z Hints
• If “DTS” is set to “Off” in “Audio” setup, the DTS
track selection option will not appear on the screen
even if the disc contains DTS tracks (page 84).
• When “Auto Display” is set to “On” (default) in
“Options” setup (page 88), playback information
automatically appears when the recorder is turned on,
etc.
1 : English DolbyDigital 3/2.1
b Note
Front (L/R) + Centre
LFE (Low Frequency
Effect)
D The current selected angle
Display 2
Example: When playing a DVD-RW (VR mode)
Checking the playing/remaining
time
You can view the playing or time information
displayed on the TV screen and the front panel
display.
Press TIME/TEXT repeatedly.
The displays differ depending on the disc type or
playing status.
A Disc type*1/format (page 8)
B Title type (only appears for Playlists)
(page 64)
C Play mode
Front panel display
Example: When playing a DVD
Playing time and number of the current title
D Recording mode (page 41)
E Playing status bar*2
Seven Basic Operations — Getting to Know Your DVD Recorder
The letters or symbols that cannot be displayed are
replaced with “*.”
Remaining time of the current title
F Title number (chapter number*3) (page 59)
(Shows either track number, scene number,
album number*3, or file number for CDs,
VIDEO CDs, DATA DVDs, or DATA CDs.)
G Album name appears for CDs with CD text,
DATA DVDs or DATA CDs when you
press TIME/TEXT repeatedly.
H Playing time (remaining time*3)
Playing time and number of the current
chapter
Remaining time of the current chapter
*1
Displays Super VIDEO CDs as “SVCD,” DATA CDs
as “CD” and DATA DVDs as “DVD.”
*2 Does not appear with VIDEO CDs, DATA DVDs, and
DATA CDs.
*3 Displayed when you press TIME/TEXT repeatedly.
Example: When dubbing a DVD
Remaining time of dubbing in progress
,continued
35
Example: When playing a VIDEO CD
Playing time and number of the current
scene or track
Example: When playing a CD
Track playing time and the current track/index number
m
Remaining time of the current track
m
5. Changing the Name of a
Recorded Programme
You can label a DVD, title, or program by entering
characters. You can enter up to 64 characters for a
title or disc name, but the actual number of
characters displayed in the menus such as the Title
List will vary. The steps below explain how to
change the name of the recorded programme.
Playing time of the disc
m
Remaining time of the disc
m
Number
buttons, SET
CD text (when available)
Example: When playing an MP3 audio track
1
2
3
4
5
6
7
8
9
0
Playing time and number of the current track
m
TITLE LIST
Current album number
Example: When viewing a JPEG image
</M/m/,,
ENTER
Current file number and total number of files in the
current album
m
Current album number and total number of albums
b Notes
• The recorder can only display the first level of a CD’s
text, such as the disc name.
• The letters or symbols that cannot be displayed are
replaced with “*.”
• Playing time of MP3 audio tracks may not be displayed
correctly.
1
2
Press TITLE LIST.
Select a title, and press ENTER.
The sub-menu appears.
3
Select “Title Name,” and press ENTER.
The display for entering characters appears.
4
Press </M/m/, to move the cursor to
the right of the screen and select “A”
(upper-case), “a” (lower-case), or
“Symbol,” and press ENTER.
The characters of the selected type are
displayed.
36
5
Press </M/m/, to select the character
you want to enter, and press ENTER.
The selected character appears at the top of
the display.
Example: Input Title Name
To use the number buttons
You can also use the number buttons to enter
characters.
In step 5 above, press a number button
repeatedly to select a character.
Example:
Press the number 3 button once to enter “D.”
Press the number 3 button three times to enter
“F.”
2
3
Press SET and select the next character.
Input Title Name
1
6
"A"
2
Back
7
"a"
3
Clear All
8
4
Space
9
Cancel
0
Finish
5
Symbol
The type of characters will change according
to the language you select in “Easy Setup.”
Some languages allow you to enter an accent
mark.
To enter a letter with an accent mark, select an
accent followed by the letter.
Example: Select “ ` ” and then “a” to enter “à.”
To insert a space, select “Space.”
6
Repeat steps 4 and 5 to enter the
remaining characters.
Input row
Input Title Name
1
-
6
"A"
2
c
Back
7
"a"
3
f
Clear All
8
Space
9
Cancel
0
Finish
4
5
Select “Finish” and press ENTER.
z Hints
• You can erase all displayed characters by pressing and
holding CLEAR for 2 seconds or more.
• You can switch between “A” (upper-case), “a” (lowercase), or “Symbol” even if you press INPUT SELECT.
Seven Basic Operations — Getting to Know Your DVD Recorder
1
Symbol
To erase a character, move the cursor to the
right of the character at the input row. Select
“Back” and press ENTER.
To insert a character, move the cursor to the
right of the point where you want to insert the
character. Select the character and press
ENTER.
To erase all of the characters, select “Clear
All” and press ENTER.
7
Select “Finish,” and press ENTER.
To cancel the setting, select “Cancel.”
37
6. Labelling and Protecting
a Disc
You can execute options effective for the entire
disc using the Disc Information display.
Protecting a disc
-RWVR
1
Insert a disc.
See “Inserting a Disc” on page 29.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
Disc Information
1
2
3
4
5
6
7
8
9
Close
DiscName
Disc Name
0
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Format
2. 3 / 4. 7GB
</M/m/,,
ENTER
TOOLS
3
4
Select “Protect Disc,” and press ENTER.
Select “Protect,” and press ENTER.
To cancel the protection
Select “Don’t Protect” in step 4.
Labelling a disc
+RW
1
-RWVR -RWVideo
z Hint
You can set protection for individual titles (page 65).
+R
-R
Insert a disc.
See “Inserting a Disc” on page 29.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
Example: When the inserted disc is a DVDRW (VR mode).
Disc Information
Close
DiscName
Disc Name
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Format
2. 3 / 4. 7GB
3
Select “Disc Name,” and press ENTER.
Enter the disc name in the “Input Disc Name”
display (page 36).
b Note
You can enter up to 64 characters for a DVD’s disc name.
The disc name may not appear when the disc is played on
other DVD equipment.
38
7. Playing the Disc on Other
DVD Equipment (Finalize)
+RW
-RWVR -RWVideo
+R
-R
1
2
3
4
5
6
7
8
9
0
Differences between the disc types
+RW
-RWVR
-RWVideo
+R
-R
Discs are automatically finalized when
removed from the recorder. However,
you may need to finalize the disc for
certain DVD equipment, or if the
recording time is short. You can edit or
record on the disc even after finalizing.
Finalizing is unnecessary when playing
a disc on VR format compatible
equipment.
Even if your other DVD equipment is
VR format compatible, you may need to
finalize the disc, especially if the
recording time is short. You can edit or
record on the disc even after finalizing.
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc. If you want to record
on it again, unfinalize or reformat the
disc (page 29). However, if you reformat
the disc, all recorded contents will be
erased.
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc.
</M/m/,,
ENTER
TOOLS
1
Insert a disc.
See “Inserting a Disc” on page 29.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
The “Disc Information” display appears.
3
Select “Finalize,” and press ENTER.
The display shows the approximate time
required for finalizing and asks for
confirmation.
Finalize
About xx min is needed for finalizing this disc.
Cannot cancel finalizing during transaction.
Do you want to finalize?
OK
4
Seven Basic Operations — Getting to Know Your DVD Recorder
Finalizing is necessary when you play discs
recorded with this recorder on other DVD
equipment.
When you finalize a DVD+RW, DVD-RW
(Video mode), DVD+R, or DVD-R, a DVD menu
will be automatically created, which can be
displayed on other DVD equipment.
Before finalizing, check the differences between
the disc types in the table below.
Cancel
Select “OK,” and press ENTER.
The recorder starts finalizing the disc.
z Hint
You can check whether the disc has been finalized or not.
If you cannot select “Finalize” in step 3 above, the disc
has already been finalized.
b Notes
• Depending on the condition of the disc, recording, or
the DVD equipment, discs may not play even if the
discs are finalized.
• The recorder may not be able to finalize the disc if it
was recorded on another recorder.
,continued
39
Unfinalizing a disc
-RWVR -RWVideo
For DVD-RWs (Video mode)
DVD-RW (Video mode) that have been finalized
to prohibit additional recording or editing can be
unfinalized to allow further recording or editing.
For DVD-RWs (VR mode)
If you cannot record or edit on a DVD-RW (VR
mode) that has been finalized with other DVD
equipment, “The disc was finalized. Unfinalize
it.” may appear.
b Note
The recorder is not able to unfinalize DVD-RWs (Video
mode) that have been finalized on another recorder.
1
Insert a disc.
See “Inserting a Disc” on page 29.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
The “Disc Information” display appears.
3
Select “Unfinalize,” and press ENTER.
The recorder starts unfinalizing the disc.
Unfinalizing may take several minutes.
40
Recording mode
Recording time (hours)
HQ (High quality)
16
Timer Recording
Before Recording
Before you start recording…
z Hint
Timer recordings will be made regardless whether or not
the recorder is turned on. You can turn off the recorder
without affecting the recording even after recording
starts.
b Note
To play a recorded disc on other DVD equipment,
finalize the disc (page 39).
Recording mode
Like the SP or LP recording mode of VCRs, this
recorder has eight different recording modes.
Select a recording mode according to the time and
picture quality you need. For example, if picture
quality is your top priority, select the High Quality
mode (HQ). If recording time is your priority,
Super Extended Play mode (SEP) can be a
possible choice. Note that recording times in the
following table are approximate and the actual
times may differ. Note also that the maximum
continuous recording time for a single title is eight
hours. Contents beyond this time will not be
recorded.
HSP
R 25
SP (Standard mode) 33
DVD*
1
1 hr. 30 min.
2
LSP
r 42
2 hr. 30 min.
LP
r 51
3
EP
r 68
4
SLP
r 101
6
SEP (Long duration) 134
8
Timer Recording
• This recorder can record on various discs. Select
the disc type according to your needs (page 8).
• Check that the disc has enough available space
for the recording (page 29). For HDD,
DVD+RWs, and DVD-RWs, you can free up
disc space by erasing titles (page 68).
• Adjust the recording picture quality and picture
size if necessary (page 46).
HDD
* The recording time for DVD+R DL (Double Layer)
discs is as follows:
HQ: 1 hour 48 minutes
HSP: 2 hours 42 mimutes
SP: 3 hours 37 mimutes
LSP: 4 hours 31 mimutes
LP: 5 hours 25 mimutes
EP: 7 hours 14 mimutes
SLP: 10 hours 51 mimutes
SEP: 14 hours 28 mimutes
“HQ+” recording mode
“HQ+” records pictures in higher quality than HQ
on the HDD. Set “HQ Setting” in “Features” setup
to “HQ+” (page 86). Maximum recording time is
10 hours. “HQ” appears in the display.
b Note
Situations below may cause slight inaccuracies with the
recording time.
– Recording a programme with poor reception, or a
programme or video source of low picture quality
– Recording on a disc that has already been edited
– Recording only a still picture or just sound
Press REC MODE repeatedly to switch the
recording modes.
41
Recording stereo and bilingual
programmes
The recorder automatically receives and records
stereo and bilingual programmes based on the
ZWEITON system or the NICAM system.
The HDD and a DVD-RW (VR mode) can record
both main and sub sounds. You can switch
between main and sub when playing the disc. For
the HDD, you can select the sound track before
recording. Select “Main,” “Sub,” or “Main+Sub”
in “HDD Bilingual Rec.” of “Options” setup
(page 87).
A DVD+RW, DVD-RW (Video mode), DVD+R,
or DVD-R can record only one sound track (main
or sub) at a time. Select the sound track using the
Setup Display before recording starts. Set “DVD
Bilingual Rec.” to “Main” (default) or “Sub” in
“Options” setup (page 87).
ZWEITON (German stereo) system
When a stereo based programme is received,
“Stereo” appears.
When a bilingual ZWEITON based programme is
received, “Main,” “Sub,” or “Main/Sub” appears.
NICAM system
When a stereo or bilingual NICAM based
programme is received, “NICAM” appears in the
front panel display.
To record a NICAM programme, be sure to set
“Audio” of “Channel Setting” in “Settings” setup
to “NICAM” (default). If the sound is not clear
when listening to NICAM broadcasts, set “Audio”
to “Standard” (see “Channel Setting” on page 76).
z Hint
You can select the audio (main or sub) while recording
bilingual programmes using the
(audio) button.
This does not affect the recorded sound.
42
Unrecordable pictures
Pictures with copy protection cannot be recorded
on this recorder.
When the recorder receives a copy guard signal,
the recorder continues to record but only a blank,
grey coloured screen will be recorded.
Copy control
signals
Copy-Free
Copy-Once
Recordable discs
HDD
+RW
-RWVR
-RWVideo
+R
-R
HDD
-RWVR (Ver.1.1 with CPRM*)
Copy-Never
None (a blank screen is
recorded)
* The recorded disc can be played only on CPRM
compatible equipment (page 8).
Timer Recording (Standard/
VIDEO Plus+)
HDD
+RW
-RWVR -RWVideo
+R
2
-R
“Start”: Sets the start time.
“Stop”: Sets the stop time.
“Prog.”: Selects the programme position or
input source.
“Media”: Selects the media, HDD or DVD.
“Mode”: Selects the recording mode
(page 41).
• If you want to change the setting for the
PDC/VPS or Update functions, select
“Details” and press ENTER. Select an item
using </, and set using M/m.
“PDC/VPS”: Sets the PDC/VPS function. See
“About the PDC/VPS function” below.
“Update” (HDD only): Automatically records
over a previously recorded programme that is
set to be recorded daily or weekly.
To return to the Timer programming menu,
select “Previous” and ENTER.
• If you make a mistake, select the item and
change the setting.
Setting the timer manually
(Standard)
2
3
4
5
6
7
8
9
0
[TIMER]
</M/m/,,
ENTER
TOOLS
x REC STOP
3
Timer Recording
“Date”: Sets the date.
The item changes as follows:
Today y Tomorrow y …… y Thu
28.10 (1 month later) y Sun (every Sunday)
y …… y Sat (every Saturday) y
Mon-Fri (Monday to Friday) y Mon-Sat
(Monday to Saturday) y Sun-Sat (Sunday to
Saturday) y Today
You can set the timer for a total of 30 programmes
(8 programmes when using the PDC/VPS
function), up to one month in advance.
There are two methods to set the timer: the
standard method and VIDEO Plus+ method.
• Standard: Set the date, time, and programme
position of the programme manually.
• VIDEO Plus+: Enter the PlusCode number
designated for each TV programme (page 45).
1
Select an item using </, and adjust
using M/m.
Select “OK,” and press ENTER.
The Timer List (page 47) appears. The
TIMER REC indicator lights up on the front
panel and the recorder is ready to start
recording.
Unlike a VCR, there is no need to turn off the
recorder before the timer recording starts.
To stop recording during timer recording
1
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
Press [TIMER].
About the PDC/VPS function
Timer - Standard
OK
Set the timer manually.
Date
Start
Today
:
VIDEO Plus+
Stop
Prog.
Media Mode
Cancel
:
PDC/VPS: On
Update: Off
Details
PDC/VPS signals are transmitted with TV
programmes in some broadcast systems. These
signals ensure that timer recordings are made
regardless of any broadcast delays, early starts, or
broadcast interruptions.
• If the “Timer – VIDEO Plus+” display
appears, press < to switch the display to
“Standard”.
,continued
43
To use the PDC/VPS function
Set “PDC/VPS” to “On” in step 2 above.
When you turn on this function, the recorder starts
scanning the channel before the timer recording
starts. If you are watching TV when scanning
starts, a message will appear on the TV screen. If
you want to watch TV, switch to your TV’s tuner
or turn off the PDC/VPS channel scan function.
Note that if you turn off the PDC/VPS channel
scan function, the timer recording will not start.
To turn off the PDC/VPS channel scan
Press TOOLS and select “PDC/VPS Scan Off.”
To ensure that the PDC/VPS function works
properly, turn off the recorder before the timer
recording starts. This will automatically turn on
the PDC/VPS channel scan function while the
recorder remains off.
Rec Mode Adjust
If there is not enough available disc space for the
recording, the recorder automatically adjusts the
recording mode to enable the entire programme to
be recorded. This function is normally set to “On.”
To cancel this function, press TOOLS while the
Timer List is displayed. Select “Rec Mode
Adjust” and press ENTER. Select “Off” and press
ENTER.
If the timer settings overlap
Overlapped timer settings are shown as follows.
Timer
These timer settings overlap. Do you want to continue?
Wed 29.10 21:00-22:00 AAB DVD SP
PDC/VPS
Wed 29.10 20:30-22:00 DEF DVD SP
PDC/VPS
OK
Cancel
To store the setting as shown, select “OK.” The
programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
To cancel the overlapped setting, select “Cancel.”
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” on page 47.
44
To extend the recording duration time while
recording
1
Press TOOLS during recording to select
“Extend Rec,” and press ENTER.
Extend Rec. Time
OK
Set the timer extend function.
Cancel
Wed 28.9 10:00-11:30 AAB
DVD SP
Extend Time
Off
2
Press M/m to select the duration time.
You can set the duration in increments of 10
minutes, for a maximum of 60 minutes.
3
Select “OK” and press ENTER.
One Touch Timer
If you use the SMARTLINK connection, you can
easily display the timer programming menu.
When the TV is turned on or in standby mode,
press [TIMER]. The recorder automatically turns
on and the TV’s input is switched to the recorder.
The Timer programming menu appears.
z Hint
You can play the recorded programme by selecting the
programme title in the Title List.
b Notes
• If a message indicating that the disc is full appears on
the screen, change the disc, or make available space for
the recording (HDD/DVD+RW/DVD-RW only)
(page 67).
• Check that the clock is correctly set before setting the
timer recording. If not, the timer recording cannot be
made.
To record a satellite programme, turn on the satellite
tuner and select the satellite programme you want to
record. Leave the satellite tuner turned on until the
recorder finishes recording. If you connect equipment
with a timer function, you can use the Synchro Rec
function (page 49).
• Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. “
” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
• The Rec Mode Adjust function only works with a timer
recording and the PDC/VPS function set to off. It does
not function with Quick Timer or Synchro Rec. In
addition, the Rec Mode Adjust function does not work
when recording to the HDD while “Auto Title Erase” is
set to “On.”
• The beginning of some recordings may not be made
when using the PDC/VPS function.
• You cannot extend the recording duration time when
“PDC/VPS” is set to “On.”
Recording TV programmes using
the VIDEO Plus+ system
3
The date, start and stop times, programme
position, recording mode, etc. setting
(page 43) appear.
The VIDEO Plus+ system is a feature that
simplifies setting the timer. Just enter the
PlusCode number listed in the TV programme
guide. The date, time, and programme position of
that programme are set automatically.
Check that the programme positions are correctly
set in “Channel Setting” in “Settings” setup
(page 76).
1
2
3
4
5
6
7
8
9
CLEAR
Timer - VIDEO Plus+
Is the following timer setting correct? To modify,
adjust each item or re-enter the timer code.
Date
Start
Stop
Wed 28.9
21 : 00
22 : 00
OK
Cancel
Prog. Media Mode
12
HDD
SP
Details
PDC/VPS: On
Update: Off
Change
• If you want to change the setting, press
</, to select the item and press M/m to
change the setting. For the PDC/VPS or
Update functions, select “Details” and
change the settings (page 43).
Timer Recording
Number
buttons, SET
Select “OK,” and press ENTER.
To re-enter the PlusCode number, select
“Change.”
4
0
Select “OK,” and press ENTER.
The TIMER REC indicator lights up on the
front panel, and the recorder is ready to start
recording.
[TIMER]
</M/m/,,
ENTER
To stop recording during timer recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
z REC
x REC STOP
If the timer settings overlap
See page 44.
1
To extend the recording duration time while
recording
Press [TIMER].
See page 44.
Timer - VIDEO Plus+
Set the timer by entering the timer code.
PlusCode No.
OK
Cancel
Standard
• If the “Timer – Standard” display appears,
press < to switch the display to “VIDEO
Plus+.”
2
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” on page 47.
z Hint
The Rec Mode Adjust function also works with this timer
method (page 44).
Press the number buttons to enter the
PlusCode number, and press SET.
• If you make a mistake, press CLEAR and reenter the correct number.
,continued
45
Using the Quick Timer function
1
Before recording starts, press TOOLS to
select “Rec Settings,” and press ENTER.
Rec. Settings
You can set the recorder to record in 30-minute
increments.
Select the item you want to change.
Press z REC repeatedly to set the duration.
Each press advances the time in 30-minute
increments. The maximum duration is six hours.
Rec Mode :
SP
HDD Rec. Picture Size:
4:3
DVD Rec. Picture Size:
4:3
Rec NR :
2
Rec Video Equalizer
0:30
1:00
5:30
6:00
(normal
recording)
The time counter decreases minute by minute to
0:00, then the recorder stops recording (power
does not turn off). Even if you turn off the recorder
during recording, the recorder continues to record
until the time counter runs out.
Note that the Quick Timer function does not work
if “TV Direct Rec” is set to “On” in “Features”
setup (page 85).
To cancel the Quick Timer
Press z REC repeatedly until the counter appears
in the front panel display. The recorder returns to
normal recording mode.
Adjusting the recording picture
quality and size
You can adjust the recording picture quality and
picture size.
1
2
3
4
5
6
7
8
9
0
</M/m/,,
ENTER
TOOLS
2
Select the item you want to adjust, and
press ENTER.
The adjustment display appears.
Example: Rec NR
Rec NR
Off
1
2
3
“Rec Mode”: Selects the recording mode for
the desired recording time and picture quality.
For more information, see “Recording mode”
on page 41.
“HDD Rec. Picture Size”/“DVD Rec. Picture
Size”: Sets the picture size of the programme
to be recorded.
• 4:3 (default): Sets the picture size to 4:3.
• 16:9: Sets the picture size to 16:9 (wide
mode).
• Auto (HDD only): Automatically selects the
actual picture size.
“DVD Rec. Picture Size” works with DVDRs and DVD-RWs (Video mode) when the
recording mode is set to HQ, HSP, or SP. For
all other recording modes, the screen size is
fixed at “4:3.”
For DVD-RWs (VR mode), the actual picture
size is recorded regardless of the setting. For
example, if a 16:9 size picture is received, the
disc records the picture as 16:9 even if “DVD
Rec. Picture Size” is set to “4:3.”
For DVD+RWs/DVD+Rs, the screen size is
fixed at “4:3.”
“Rec NR” (noise reduction): Reduces noise
contained in the video signal.
46
“Rec Video Equalizer”: Adjusts the picture in
greater detail.
Press M/m to select the item you want to
adjust, then press ENTER.
• Contrast: Changes the contrast.
• Brightness: Changes the overall brightness.
• Colour: Makes the colours deeper or lighter.
3
The default setting is underlined.
“Rec NR”: (weak) Off 1 ~ 2 ~ 3 (strong)
“Rec Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
Repeat steps 2 and 3 to adjust any other items.
HDD
+RW
-RWVR -RW
+RVideo
+R
-R
You can check, change, or cancel timer settings
using the Timer List.
1
2
3
4
5
6
7
8
9
Timer Recording
Adjust the setting using </M/m/,, and
press ENTER.
Checking/Changing/
Cancelling Timer Settings
(Timer List)
0
b Notes
• If one programme contains two picture sizes, the
selected size is recorded. However, if the 16:9 signal
cannot be recorded as 16:9, it is recorded as 4:3.
• When playing a 16:9 size picture recorded as 4:3, The
image is fixed to 4:3 letter box regardless of the setting
in “TV Type” of “Video” setup (page 81).
• Remnants of images may appear on your screen when
using “Rec NR.”
• “Rec Video Equalizer” does not work with RGB
signals.
TIMER LIST
</M/m/,,
ENTER
O RETURN
TOOLS
/
1
Press TIMER LIST.
The Timer List appears.
Creating chapters in a title
10:30
TIMER LIST
The recorder can automatically divide a recording
(a title) into chapters by inserting chapter marks
during recording. To disable this function, set
“Auto Chapter” in “Features” setup to “Off”
(page 85).
When recording on the HDD or a DVD-RW (VR
mode)
The recorder detects changes in the picture and
sound and automatically inserts chapter marks.
You can also insert and erase chapter marks
manually (page 68).
When recording on other recordable discs
Chapter marks are inserted at approximately
6-minute intervals during recording.
b Note
When dubbing (page 71), the chapter marks in the
dubbing source are not retained in the dubbed title.
Mon-Sat
22:00-22:15 AAB
SP
Fri
29.10 20:30-21:30 DEF
SP
Fri
29.10 21:00-22:00 GHI
SLP
Sat 30.10 16:00-17:00 DEF
SLP
PDC
VPS
PDC
VPS
Timer information displays the recording
date, time, recording mode, etc.
: Indicates that the setting is overlapped by
another setting.
(green): Indicates the setting can be
recorded.
z (red): Indicates the setting currently being
recorded.
a (grey): Indicates that the setting cannot be
recorded in the selected recording mode.
: Indicates the setting being recorded on
the HDD.
: Indicates the setting being recorded on a
DVD.
,continued
47
: Indicates the setting that the Update
function is set for.
When all of the timer settings do not fit on the
list, scroll bar appears.
To view the hidden timer settings, press M/m.
2
Select the timer setting you want to check/
change/cancel, and press ENTER.
The sub-menu appears.
3
Select one of the options, and press
ENTER.
“Modify”: Changes the timer setting.
Select an item using </, and adjust using
M/m. For the PDC/VPS or Update functions,
select “Details” and change the settings
(page 43). Select “OK,” and press ENTER.
Modify
OK
Modify the timer setting.
Cancel
Date
Mon-Sat
Prog. Media Mode
Stop
22 : 00
22 : 15
AAB
PDC/VPS: Off
HDD
SP
Update: On
Details
When the timer settings overlap
The programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
7:00
8:00
9:00
10:00
A
will be cut off
B
When the recordings start at the same time
The programme that is set last has priority. In this
example, timer setting B is set after A, so the first
part of timer setting A will not be recorded.
7:00
8:00
9:00
10:00
A
B
When the end time of one recording and the
start time of another are the same
After finishing the previous recording, the other
recording may be delayed.
7:00
9:00
10:00
A
“Erase”: Erases the timer setting. Select
“OK,” and press ENTER.
To scroll the list display by page (Page mode)
Erase
Are you sure you want to erase this timer setting?
Mon-Sat 22:00-22:15
HDD SP
AAB
OK
Press
/
while the list display is turned on.
Each time you press
/
, the entire Timer
List changes to the next/previous page of timer
settings.
To turn off the Timer List
Press TIMER LIST or O RETURN.
Cancel
“Check Overlap”: Checks for overlapped
settings.
Check Overlap
These timer settings overlap.
Fri
29.10
20:30-21:30
DEF
DVD SP
Fri
29.10
21:00-22:00
GHI
DVD SLP PDC/VPS
PDC/VPS
Close
Select “Close” to return to the Timer List.
To change or cancel the setting, repeat steps 2
and 3 above.
48
B
z Hint
While recording, you cannot modify the timer setting for
the current recording, but you can extend the recording
duration of the recording time (page 44).
b Notes
• When “PDC/VPS” is set to “On” for one or more timer
recordings, the start times may change in the event of a
broadcast delay or early start.
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
• Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. “
” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
Automatically erasing old titles
(Auto Title Erase)
Recording From Connected
Equipment
HDD
1
HDD
+RW
-RWVR -RW
+RVideo
HDD
Press TIMER LIST.
The Timer List appears.
2
Press TOOLS to select “Auto Title Erase,”
and press ENTER.
3
Select “On,” and press ENTER.
-R
DVD
1
2
3
4
5
6
7
8
9
0
The default setting is “Off.”
+R
INPUT SELECT
Timer Recording
If there is not enough space for a timer recording,
the recorder automatically erases old titles
recorded on the HDD. The oldest, played title is
erased. The protected titles are not erased.
</M/m/,,
ENTER
TOOLS
REC MODE
X REC PAUSE
x REC STOP
SYNCHRO
REC
Recording from connected
equipment with a timer (Synchro
Rec)
You can set the recorder to automatically record
programmes from connected equipment that has a
timer function (such as a satellite tuner). Connect
the equipment to the LINE 3/DECODER jack of
the recorder (page 25).
When the connected equipment turns on, the
recorder starts recording a programme from the
LINE 3/DECODER jack.
1
Before recording, select HDD or DVD.
If you select DVD, insert a recordable DVD
(see “Inserting a Disc” on page 29).
2
Set “Synchro Rec” in “Features” setup to
“Record to HDD” or “Record to DVD”
(page 86).
,continued
49
3
Press INPUT SELECT repeatedly to select
“L3.”
4
Select the line input audio when recording
a bilingual programme on the HDD or DVDRWs (VR mode).
Press TOOLS to select “Line Audio Input,”
and press ENTER. Then select “Bilingual,”
and press ENTER.
For details about bilingual recording, see
page 42.
5
Press REC MODE repeatedly to select the
recording mode.
For details about the recording mode, see
page 41.
6
Set the timer on the connected equipment
to the time of the programme you want to
record, and turn it off.
7
Press SYNCHRO REC.
The SYNCHRO REC indicator lights up on
the front panel. The recorder is ready to start
Synchro-Recording.
The recorder automatically starts recording
when it receives an input signal from the
connected equipment. The recorder stops
recording when the connected equipment
turns off.
b Notes
• The recorder starts recording only after detecting the
video signal from the connected equipment. The
beginning of the programme may not be recorded
regardless of whether or not the recorder’s power is on
or off.
• During Synchro-Recording, other operations such as
normal recording cannot be done.
• To use the connected equipment while the recorder is
standing by for Synchro-Recording, cancel SynchroRecording by pressing SYNCHRO REC. Be sure to
turn off the connected equipment and press
SYNCHRO REC to reset Synchro-Recording before
the timer recording starts.
• The Synchro Rec function does not work when “Line3
Input” of “Scart Setting” in “Video” setup is set to
“Decoder” (page 82).
• The Synchro Rec function does not work with some
tuners. For details, see the tuner’s operating
instructions.
• While the recorder is standing by for SynchroRecording, the Auto Clock Set function (page 79) does
not work.
• To use the Synchro Rec function, you must first set the
recorder’s clock correctly.
If the timer settings of a Synchro-Recording
and another timer recording overlap
Regardless of whether or not the programme is a
Synchro Rec programme, the programme that
starts first has priority and the second programme
starts recording only after the first programme has
finished.
To stop recording
Press x REC STOP or SYNCHRO REC.
To cancel Synchro Rec
Press SYNCHRO REC.
The SYNCHRO REC indicator on the recorder
turns off.
7:00
8:00
9:00
10:00
First
programme
Second
programme
will be cut off
Recording from connected
equipment without a timer
You can record from a connected VCR or similar
device. To connect a VCR or similar device, see
“Connecting a VCR or Similar Device” on
page 23.
1
Press HDD or DVD.
If you select DVD, insert a recordable DVD
(see “Inserting a Disc” on page 29).
50
2
Press INPUT SELECT to select an input
source according to the connection you
made.
The front panel display changes as follows:
programme
position
L2
L3
L4
Select the line input audio when recording
a bilingual programme on the HDD or DVDRWs (VR mode).
Press TOOLS to select “Line Audio Input,”
and press ENTER. Then select “Bilingual,”
and press ENTER.
For details about bilingual recording, see
page 42.
4
Timer Recording
3
L1
Press REC MODE repeatedly to select the
recording mode.
For details about the recording mode, see
page 41.
5
Press X REC PAUSE to set this recorder to
record pause.
6
Insert the source tape into the connected
equipment and set to playback pause.
7
At the same time, press X REC PAUSE on
this recorder and the pause or play button
on the connected equipment.
Recording starts.
To stop recording, press x REC STOP on this
recorder.
z Hint
You can adjust the settings for the recording picture
before recording. See “Adjusting the recording picture
quality and size” on page 46.
b Notes
• When recording a video game image, the screen may
not be clear.
• Any programme that contains a Copy-Never copy
guard signal cannot be recorded. The recorder
continues to record, but a blank screen will be recorded.
51
Example: DVD-RW (VR mode)
Playback
TITLE LIST
ORIGINAL
12 Tennis
Playing
Fri 28.10. 2005 13:00
+RW
VCD
AAB
(0H30M) LSP 0.9GB
11 Travel
DEF
Wed 26.10. 2005 20:00 (0H30M) SEP 0.3GB
10 Mystery
HDD
DVD
4.3 / 4.7GB
-RWVR -RWVideo
CD
+R
-R
Tue 25.10. 2005 9:00
AAB
(1H00M) SLP 0.8GB
9 World Sports
DATA DVD DATA CD
GHI
Wed 19.10. 2005 20:00 (1H00M) SEP 0.6GB
3
Select the title, and press ENTER.
The sub-menu appears.
Z
HDD
DVD
1
2
3
4
5
6
7
8
9
0
PROG +/–
INPUT
SELECT
SUR
TITLE LIST
TOP MENU
MENU
</M/m/,,
ENTER
TOOLS
PROGRESSIVE
/
>
4
Select “Play,” and press ENTER.
Playback starts from the selected title.
To use the DVD’s Menu
When you play a DVD VIDEO, or a finalized
DVD+RW, DVD-RW (Video mode), DVD+R, or
DVD-R, you can display the disc’s menu by
pressing TOP MENU or MENU.
To play VIDEO CDs with PBC functions
PBC (Playback Control) allows you to play
VIDEO CDs interactively using the menu on your
TV screen.
When you start playing a VIDEO CD with PBC
functions, the menu appears.
Select an item using the number buttons and press
ENTER. Then, follow the instructions in the menu
(press H when “Press SELECT” appears).
The PBC function of Super VIDEO CDs does not
work with this recorder. Super VIDEO CDs are
played in continuous play mode only.
.
To stop playback
H/X/x
Press x.
To playback quickly with sound (Scan Audio)
1
Press HDD or DVD.
• If you select DVD, insert a disc (see
“Inserting a Disc” on page 29).
• If you insert a DVD VIDEO, VIDEO CD, or
CD, press H. Playback starts.
2
Press TITLE LIST.
For details about the Title List, see “3. Playing
the Recorded Programme (Title List)” on
page 32.
52
When you press M during playback of a title
recorded in the HDD, you can play quickly with
dialogue or sound (“x1.5” appears).
No sound is output when you press M two or
more times to change search speed.
To resume playback from the point where you
stopped (Resume Play)
When you press H again after you stop
playback, the recorder resumes playback from the
point where you pressed x.
To start from the beginning, press TOOLS to
select “Play Beginning,” and press ENTER.
Playback starts from the beginning of the title/
track/scene.
If you use the SMARTLINK connection, you can
easily start playing.
Press H. The recorder and your TV
automatically turn on and the TV’s input is
switched to the recorder. Playback starts
automatically.
One Touch Menu
If you use the SMARTLINK connection, you can
easily display the Title List.
Press TITLE LIST. The recorder and your TV
automatically turn on and the TV’s input is
switched to the recorder. The Title List appears.
Playback
The point where you stopped playing is cleared
when:
– you open the disc tray (except for HDD).
– you play another title (except for HDD).
– you switch the Title List menu to Original or
Playlist (HDD/DVD-RW in VR mode only).
– you edit the title after stopping playback.
– you change the settings on the recorder.
– you turn off the recorder (VIDEO CD/CD/
DATA DVD/DATA CD only).
– you make a recording (except for HDD/DVDRWs in VR mode).
– you switch between JPEG and MP3.
One Touch Play
z Hints
• You can also use the H button in step 3 (page 52) to
start playback.
• Even if you select “Factory Setup” in “Options” setup
(page 88), the Child Lock remains set.
b Note
You cannot resume playback during TV Pause.
To play restricted DVDs (Parental Control)
If you play a restricted DVD, the message “Do
you want temporarily change parental control to
*?” appears on your TV screen.
1
Select “OK” and press ENTER.
The display for entering your password
appears.
2
Enter your four-digit password using the
number buttons.
3
Press ENTER to select “OK.”
The recorder starts playback.
To register or change the password, see “Parental
Control (DVD VIDEO only)” on page 85.
To lock the disc tray (Child Lock)
You can lock the disc tray to prevent children from
ejecting the disc.
When the recorder is turned on, hold down x until
“LOCKED” appears in the front panel display.
The Z (open/close) button does not work while
the Child Lock is set.
To unlock the disc tray, hold down x until
“UNLOCKED” appears in the front panel display
when the recorder is turned on.
,continued
53
Playback options
To check the position of the buttons below, see the illustration on page 52.
Buttons
Operations
(audio)
HDD -RWVR
VCD
Selects one of the audio tracks recorded on the disc when pressed repeatedly.
DVD
DVD : Selects the language.
HDD -RWVR : Selects the main or sub sound.
CD
VCD
(subtitle)
CD
: Selects stereo or monaural audio tracks.
Selects a subtitle language when pressed repeatedly.
DVD
(angle)
Selects an angle when pressed repeatedly.
If various angles (multi-angles) for a scene are recorded on the disc, “
appears in the front panel display.
DVD
SUR (surround)
+RW
+R
-RWVR -RWVideo
-R
DVD
”
Selects one of the TVS effects when pressed repeatedly.
TVS* (TV Virtual Surround) lets you enjoy virtual surround sound effects
created from the front left and right speakers. The selected setting is displayed
in the front panel display for a few seconds.
“TVS OFF”: No surround effect
“TVS DYNAMIC”: Creates one set of virtual rear speakers.
“TVS WIDE”: Creates five sets of virtual rear speakers.
“TVS NIGHT”: Creates five sets of virtual rear speakers. Effective at low
volume.
“TVS STANDARD”: Creates three sets of virtual rear speakers. Effective
when you use two separate front speakers.
* TVS was developed by Sony to produce home surround sound with just a stereo
TV.
PROGRESSIVE
+RW
-RWVR
-RWVideo
+R
-R
DVD
VCD
HDD
/
(instant replay/
instant advance)
HDD
+RW
-RWVR
-RWVideo
+R
-R
Switches the type of video output signal to interlace or progressive format
(page 16).
Replays the scene/briefly fast forwards the scene.
DVD
. (previous)/
> (next)
54
Goes to the beginning of the previous/next title/chapter/scene/track.
For the HDD, you cannot go to the beginning of the previous/next title.
Buttons
Operations
(fast reverse/fast forward)
Fast reverses/fast forwards the disc when pressed during playback.
Search speed changes as follows:
fast reverse fast forward
m1 T t 1M*1
m2 T T t t 2M
m3*2 T T T t t t 3M*2
When you press and hold the button, fast forward/fast reverse continues at the
selected speed until you release the button.
*1 When
(slow, freeze frame)
HDD
+RW
-RWVR
-RWVideo
+R
-R
Plays in slow motion when pressed for more than one second in pause mode.
Plays one frame at a time when pressed briefly in pause mode.
Playback
you press M once during playback of a title recorded in the HDD, you
can play quickly with sound (“x1.5” appears).
*2 m 3 and 3M are only available for the HDD and DVDs.
VCD *
DVD
* Playback direction only
X (pause)
Pauses playback.
To resume normal playback, press H.
b Notes
• To enjoy the TVS function, set “Digital Out” to “On”
and “Dolby Digital” to “D-PCM” and “MPEG” to
“PCM” in “Audio” setup.
• The volume may be reduced when surround effects are
set.
• When the playback signal does not contain a signal for
the rear speakers, the surround effects will be difficult
to hear.
In addition, the surround effects may also be difficult to
hear depending on the title being played and the
environment where the recorder is being used.
• When you select one of the surround modes, turn off
the surround settings of the connected TV or amplifier
(receiver).
• Make sure that your listening position is between and
at an equal distance from your speakers, and that the
speakers are located in similar surroundings.
• Angles and subtitles cannot be changed with titles
recorded on this recorder.
• When you use the DIGITAL OUT (COAXIAL) jack to
listen to MPEG audio signals and set “MPEG” to
“MPEG” in “Audio” setup, no sound will come from
your speakers if you select one of the TVS modes.
• 96 kHz PCM audio and DTS audio do not have
surround effects.
• The surround effects do not work while performing
playback quickly with sound.
Notes on playing DTS sound tracks on a CD
• When playing DTS-encoded CDs, excessive noise will
be heard from the analogue stereo jacks. To avoid
possible damage to the audio system, the consumer
should take proper precautions when the analogue
stereo jacks of the recorder are connected to an
amplification system. To enjoy DTS Digital
Surround™ playback, an external 5.1-channel decoder
system must be connected to the digital jack of the
recorder.
• Set the sound to “Stereo” using the
(audio)
button when you play DTS sound tracks on a CD
(page 54).
Notes on playing DVDs with a DTS sound track
DTS audio signals are output only through the DIGITAL
OUT (COAXIAL or OPTICAL) jack.
When you play a DVD with DTS sound tracks, set
“DTS” to “On” in “Audio” setup (page 84).
,continued
55
3
Adjusting the picture quality
HDD
DVD
1
+RW
-RWVR -RWVideo
+R
The default settings are underlined.
“Y NR”: (weak) Off 1
2 3 (strong)
“C NR”: (weak) Off 1
2 3 (strong)
“BNR”: (weak) Off 1
2 3 (strong)
“MNR”: (weak) Off 1
2 3 (strong)
“DVE”*: (weak) Off 1
2 3 (strong)
“PB Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
• Hue: (red) –3 ~ 0 ~ 3 (green)
Repeat steps 2 and 3 to adjust any other items.
-R
VCD
Press TOOLS during playback to select
“Video Settings,” and press ENTER.
Video Settings
Select the item you want to change.
Y NR :
2
C NR :
2
BNR :
2
MNR :
1
DVE :
Off
* “1” softens the outlines of the images. “2”
enhances the outlines and “3” enhances them more
than “2.”
PB Video Equalizer
2
Select an item, and press ENTER.
The adjustment display appears.
“Y NR” (luminance noise reduction):
Reduces noise contained in the luminance
element of the video signal.
“C NR” (chroma noise reduction): Reduces
noise contained in the colour element of the
video signal.
“BNR” (block noise reduction): Reduces
“block noise” or mosaic like patterns in the
picture.
“MNR” (mosquito noise reduction): Reduces
the faint noise appearing around the outlines
of the images. The noise reduction effects are
automatically adjusted within each setting
range according to the video bit rate and other
factors.
“DVE” (digital video enhancer): Sharpens the
outlines of the images.
“PB Video Equalizer” (Playback video
equalizer): Adjusts the picture in greater
detail.
Select an item and press ENTER.
• Contrast: changes the contrast.
• Brightness: changes the overall brightness.
• Colour: makes the colours deeper or lighter.
• Hue: changes the colour balance.
56
Press </, to adjust the setting, and
press ENTER.
b Notes
• If the outlines of the images on your screen become
blurred, set “BNR” and/or “MNR” to “Off.”
• Depending on the disc or the scene being played, the
above BNR, MNR, Y NR, or C NR effects may be hard
to discern. And, these functions may not work with
some screen sizes.
• When using the DVE function, noise found in the title
may become more apparent. In this case, it is
recommended that you use the BNR function with the
DVE function. If the condition still does not improve,
set the DVE level to “1” or “Off.”
Adjusting the sound quality
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
DATA CD
1
Press TOOLS during playback to select
“Audio Settings,” and press ENTER.
2
Select an item, and press ENTER.
“Surround” (TVS): Selects one of the
surround modes. For more information, see
“Playback options” on page 54.
* Sampling frequency of audio source. This
function only adjusts the output signals from the
LINE 1 – TV, LINE 3/DECODER, or LINE 2
OUT (AUDIO L/R).
3
Press </M/m/, to select the option,
and press ENTER.
b Note
There may be little effect by changing the Audio Filter
depending on the disc or playback environment.
Pausing a TV Broadcast (TV Pause)
You can pause a current TV broadcast, and then
continue watching the programme at a later time.
This is useful when you receive an unexpected
phone call or visitor while watching TV.
1
While viewing a TV broadcast with this
recorder, press X.
The picture pauses. You can pause the picture
for up to three hours.
News
ABCD 9
Stereo
TV pause
2
Press X or H again to resume watching
the programme.
b Notes
• Paused titles are not saved to the HDD.
• This function is cancelled when:
– x (stop) is pressed.
– PROG +/– is pressed.
– DVD is pressed.
– Z (open/close) is pressed.
– TITLE LIST is pressed.
– INPUT SELECT is pressed.
– the recorder is turned off.
– a timer recording or Synchro Recording is started.
– the PDC/VPS function is “On” and channel scan is
started.
– regular dubbing is started.
• It may take a few seconds to resume playback of the
paused programme.
• Even if you fast forward the recorded programme,
there will always be a time difference of about one
minute or more between the recorded programme and
the current TV broadcast.
Playback
“Audio Filter”: Selects the digital filter to
reduce noise above 22.05 kHz (Fs* is 44.1
kHz), 24 kHz (Fs is 48 kHz), or 48 kHz (Fs is
above 96 kHz).
• Sharp (default): Provides a wide frequency
range and spatial feeling.
• Slow: Provides smooth and warm sound.
“AV SYNC”: When the video is delayed, this
function delays the audio for synchronization
with the video (0 to 120 milliseconds). Larger
numbers indicate a longer audio delay for
synchronization with the video. When
dubbing to a VCR or other video recording
equipment, be sure to return this setting to 0
ms (default).
Playing from the beginning of the
programme you are recording
(Chasing Playback)
HDD
-RWVR
“Chasing Playback” allows you to view the
recorded part of a programme while the recording
is being made. You do not need to wait until the
recording finishes.
Press TOOLS while recording to select
“Chasing Playback,” and press ENTER.
Playback starts from the beginning of the
programme you are recording.
When you fast forward to the point that you are
recording, Chasing Playback returns to normal
playback.
b Notes
• For DVD-RWs (VR mode), this function does not
work when recording:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
• The DVD’s picture on your TV screen freezes for a few
seconds when you fast forward/fast reverse or instant
replay/advance the recording.
• Chasing Playback is possible from one minute or more
after recording starts.
• Even if you fast forward the recorded programme,
there will always be a time difference of about one
minute or more between the recorded programme and
the current TV broadcast.
,continued
57
Playing a previous recording while
making another (Simultaneous Rec
and Play)
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
DATA DVD DATA CD
“Simultaneous Rec and Play” allows you to view
a previously recorded programme while recording
programmes. Playback continues even if a timer
recording starts. Use this function as follows:
• While recording to the HDD:
Play another title on the HDD.
Play a previously recorded programme on a
DVD by pressing DVD.
• While recording to a DVD:
Play a previously recorded programme on the
HDD by pressing HDD.
• While recording to a DVD-RW (VR mode)*1:
Play another title on the same DVD-RW (VR
mode) disc.*2
*1
Simultaneous Rec and Play function does not work
when you record:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
*2 Picture noise may appear depending upon the
condition of the recording, or when playing a title
recorded in the HQ or HSP recording mode. The
picture freezes for a few seconds when you use fast
forward/fast reverse or instant replay/advance.
You can also play a DVD VIDEO, VIDEO CD,
Super VIDEO CD, CD, DATA DVD, or DATA
CD while recording on the HDD.
Example: Play another title on the HDD while
recording to the HDD.
58
1
While recording, press TITLE LIST to
display the HDD Title List.
2
Select the title you want to play, and press
ENTER.
3
Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
Example: Play a DVD while recording to the
HDD.
1
While recording, press DVD and insert the
DVD into the recorder.
2
Press TITLE LIST to display the DVD Title
List.
3
Select the title you want to play, and press
ENTER.
4
Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
b Note
You cannot play a DVD or VIDEO CD recorded in the
NTSC colour system while recording on the HDD. When
playing a VIDEO CD, be sure to set “Colour System” to
“PAL” (page 86).
Searching by title number or time
code
Searching for a Title/
Chapter/Track, etc.
HDD
DVD
Number
buttons, SET
1
2
3
4
5
6
7
8
9
CLEAR
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
DATA DVD DATA CD
You can search a disc by title, chapter, scene or
track. As titles and tracks are assigned individual
numbers, select the title or track by entering its
number. You can also search for a scene using the
time code.
0
Press TOOLS during playback to select a
search method, and press ENTER.
Playback
1
</M/m/,,
ENTER
“Title Search” (for DVDs)
“Chapter Search” (for HDD/DVDs)
“Track Search” (for CDs/DATA CDs)
“Search” (for VIDEO CDs)
“Album Search” (for DATA DVDs/DATA
CDs)
“Time Search” (for HDD/DVDs): Searches
for a starting point by entering the time code.
“File Search” (for DATA DVDs/DATA CDs)
TOOLS
VISUAL
SEARCH
The display for entering the number appears.
Example: Title Search
Searching by Thumbnail (Visual
Search)
HDD
+RW
-RWVR -RWVideo
+R
-R
Each chapter is displayed as a thumbnail. You can
search for the desired scene visually.
1
Title : -- (21)
The number in parentheses indicates the total
number of titles, tracks, etc.
2
Press VISUAL SEARCH during playback.
VISUAL SEARCH
For example: Time Search
To find a scene at 2 hours, 10 minutes, and 20
seconds, enter “21020.”
If you make a mistake, press CLEAR to
cancel the number, then select another
number.
9 World Sports
Chapter 4(30)
0:12:45
3
2
Select a scene using </,, and press
ENTER.
Press the number buttons to select the
number of the title, chapter, track, time
code, etc., you want.
Press SET.
The recorder starts playback from the selected
number.
Playback of the selected scene is started.
b Note
“Title Search” is not applicable to the HDD.
59
Playing MP3 Audio Tracks
or JPEG Image Files
Selecting an MP3 album or track
1
Press TITLE LIST.
The album list appears.
To change the page, press
DATA DVD DATA CD
You can play MP3 audio tracks and JPEG image
files on DATA CDs (CD-ROMs/CD-Rs/CDRWs) or JPEG image files on DATA DVDs
(DVD-ROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs).
1
2
3
4
5
6
7
8
9
.
TITLE LIST
Music Album
2
1
Opera
Classic
2
Symphony
Classic
3
Samba
Dance
4
Live
Jazz
5
Piano
Jazz
6
My heart
Pop music
7
Paradise
Pop music
8
The Best
Pop music
Select an album, and press ENTER.
The sub-menu appears.
3
0
DISPLAY
/
Select “View Album,” and press ENTER.
The track list appears.
To change the page, press
TIME/TEXT
/
.
TITLE LIST
</M/m/,,
ENTER
TITLE LIST
8 The Best
TOOLS
/
.
m
>
M
H
x
4
1
Insert a disc.
See “Inserting a Disc” on page 29.
2
1
01 Holiday
2
02 Lonely
3
03 Candy
4
04 Rainy day
5
05 Station
6
06 Magic
7
07 Moon
8
08 Butterfly
Select a track, and press ENTER.
“Play”: Plays the track.
“Play Beginning”: Plays the beginning of the
track.
“Track Data”: Shows data about the track
such as artist and album name.
Press H.
For MP3 discs, playback starts from the first
MP3 audio track on the disc.
For JPEG files, a slideshow of the pictures on
the disc begins.
If the DATA CD contains both MP3 audio
tracks and JPEG image files, playback starts
from the JPEG image files the first time H is
pressed.
To stop playback
Press x.
To fast forward or review a track
Press m/M during playback.
To go to the next or previous MP3 audio track
Press . or > during playback. If you
repeatedly press . or >, you will go to the
next or previous album.
To go to the next or previous album
Press
z Hint
Press the
/
during playback.
(audio) button to switch between stereo
or monaural audio tracks.
60
Selecting a JPEG album or image
1
Press TITLE LIST.
The album list appears.
To change the page, press
/
.
To change the slideshow speed
Press TOOLS while the album list or image list is
displayed to select “Slideshow Speed,” and press
ENTER. Then select the speed from “Fast”
(quick), “Normal,” and “Slow.”
To go to the next or previous album
Press
TITLE LIST
/
while the JPEG image is displayed.
Photo Album
1
Flowers
ROOT
2
Aquarium
Summer
3
Summer
Hiking
Summer
5
Tennis match
Summer
6
Zoo
Summer
7
Consert
Winter
8
Party
Winter
Select an album, and press ENTER.
The sub-menu appears.
3
Select “View Album,” and press ENTER.
The image list appears.
To change the page, press
b Notes
/
.
TITLE LIST
6 Zoo
1
2
3
4
5
6
7
8
9
10
11
12
DSC00029 25.11.2005 15:50
4
Playback
2
Festival
4
z Hints
• If you are playing a DATA CD that has both MP3 and
JPEG files, you can switch between photo and music
albums by using the </, buttons when the album
list is displayed.
• You can rotate a JPEG image by using the </,
buttons when the image is displayed.
• Press DISPLAY repeatedly to show information about
the JPEG album or image on your TV screen. Then
press TIME/TEXT to toggle between the current
selected image number and album number.
Select an image, and press ENTER.
“View Image”: Shows the image on the entire
screen.
“Slideshow”: Shows the images in the album
as a slideshow.
“Image Data”: Shows data about when the
picture was taken.
• If the DVD disc, such as a disc from a DVD video
camera, contains both video and JPEG images, only the
video can be played back.
• Some JPEG files, especially files of three million
pixels or more, may lengthen the slideshow interval.
• Rotated JPEG images will not be saved when you press
x or switch to another folder.
• Images larger than 720 × 480 will be reduced to 720 ×
480 when displayed.
• Images larger than 4 mega bytes cannot be displayed.
• Progressive JPEG images cannot be displayed.
• When you attempt to play a broken file or a file that
does not satisfy the play conditions,
appears but
the recorder cannot play the file.
To stop viewing the JPEG image
Press x.
To view the next or previous picture
Press ./> while the picture is displayed.
To rotate a picture
Press TOOLS while the image is displayed to
select “Rotate Right” or “Rotate Left,” and press
ENTER.
,continued
61
About MP3 audio tracks and JPEG
image files
MP3 audio tracks or JPEG image
files that the recorder can play
MP3 is audio compression technology that
satisfies certain ISO/MPEG regulations. JPEG is
image compression technology.
You can play MP3 (MPEG1 Audio Layer 3)
format audio tracks and JPEG image files on
DATA CDs (CD-ROMs/CD-Rs/CD-RWs) or
JPEG image files on DATA DVDs (DVD-ROMs/
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs).
DATA CDs discs must be recorded according to
ISO9660 Level 1, Level 2 or Joliet format for the
recorder to recognize the MP3 tracks. DATA
DVDs must be recorded in Universal Disc Format
(UDF). You can also play discs recorded in
MultiSession.
See the instructions supplied with the CD-R/CDRW/DVD-R/DVD-RW drives and the recording
software (not supplied) for details on the recording
format.
The recorder can play the following tracks and
files:
– MP3 audio tracks with the extension “.MP3,”
“.mp3,” or “Mp3.”
– JPEG image files with the extension “.JPEG,”
“.jpg,” “.JPG,” “.Jpg,” “.jpeg,” or “.Jpeg.”
– JPEG image files that conform to the DCF*
image file format.
Note on MultiSession/Border discs
If MP3 audio tracks or JPEG image files are
recorded in the first session/border, the recorder
will also play MP3 audio tracks or JPEG image
files in other sessions/borders. If audio tracks and
images in Music CD format or Video CD format
are recorded in the first session/border, only the
first session/border will be played back.
b Note
The recorder may not be able to play some DATA CDs/
DATA DVDs created in the Packet Write format.
62
* “Design rule for Camera File system”: Image standards
for digital cameras regulated by JEITA (Japan
Electronics and Information Technology Industries
Association).
b Notes
• The recorder will play any data with the extension
“.MP3,” “.mp3,” “Mp3,” “.JPEG,” “.jpg,” “.JPG,”
“.Jpg,” “.jpeg,” or “.Jpeg” even if they are not in MP3
or JPEG format. Playing these data may generate a loud
noise which could damage your speaker system.
• The recorder does not conform to audio tracks in
mp3PRO format.
• Some files cannot be played.
• The letters that cannot be displayed are replaced with
“*.”
b Notes
About playback order of albums,
tracks, and files
Albums play in the following order:
Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
ROOT
Playback
Album
• Depending on the software you use to create the DATA
DVD/DATA CD, the playback order may differ from
the above illustration.
• No more than a total of 199 individual folders can be
played. (Folders that do not contain JPEG/MP3 files
are counted as well).
• No more than a total of 999 folders and files can be
played. (Files other than JPEG/MP3 files, and folders
that do not contain JPEG/MP3 files are counted as
well.)
• No more than 200 folders and files can be recognized
in a single folder. (Folders that do not contain JPEG/
MP3 files are counted as well.)
• Proceeding to the next or another album may take some
time.
• This recorder supports MP3 audio bit rates up to 160
kbps.
MP3 audio track/
JPEG image file
When you insert a DATA CD/DATA DVD and
press H, the numbered tracks (or files) are
played sequentially, from 1 through 7. Any
sub-albums/tracks (or files) contained within a
currently selected album take priority over the
next album in the same tree. (Example: C
contains D so 4 is played before 5.) When you
press TITLE LIST and the list of album names
appears (page 35), the album names are arranged
in the following order: A t B t C t D t
F t G. Albums that do not contain tracks (or
files) (such as album E) do not appear in the list.
z Hints
• If you add numbers (01, 02, 03, etc.) to the front of the
track/file names when you store the tracks (or files) in
a disc, the tracks and files will be played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create albums
with no more than two trees.
63
To create and edit Playlist titles
Erasing and Editing
Before Editing
This recorder offers various edit options for
various disc types. Before you edit, check the disc
type in the front panel display, and select the
option available for your disc (page 8).
b Notes
• You may lose the edited contents if you remove the disc
or a timer recording starts while editing.
• DVD discs created by DVD video cameras cannot be
edited on this recorder.
Edit options for the HDD and DVDRWs (VR mode)
A Playlist is a group of Playlist titles created from
the original title for editing purposes. When you
create a Playlist, only the control information
necessary for playback, such as the playback
order, is stored on the disc. Since the original titles
are left unaltered, Playlist titles can be re-edited.
Example: You have recorded the final few
matches of a football tournament on a DVD-RW
(VR mode). You want to create a digest with the
goal scenes and other highlights, but you also want
to keep the original recording.
Original
Playlist
HDD -RWVR
You can enjoy advanced edit functions. First you
have two options for the HDD and DVD-RWs
(VR mode): editing either the original recording
(called the “original”), or the playback
information created from the original (called a
“Playlist”). Since each is different in nature and
offers different merits, read the following and
select the one that better suits your needs.
To edit original titles
Edits made to the original titles are final. If you
plan to retain an unaltered original recording,
create and edit a Playlist (see below). The edit
functions available for original titles are:
– Labelling a title (page 65).
– Setting protection against erasure (page 65).
– Erasing a title (page 65).
– Erasing multiple titles (page 67).
– Erasing a section of a title (A-B Erase) (page 66).
– Erasing all titles on the disc (page 68).
– Erasing a chapter (page 66).
– Dividing one title into two titles (HDD only)
(page 67).
64
In this case, you can compile highlight scenes as a
Playlist title. You can even rearrange the scene
order within the Playlist title (“Creating and
Editing a Playlist” on page 69).
The advanced edit functions available for Playlist
titles are:
– Setting protection against erasure (HDD only)
(page 65).
– Labelling a title (page 65).
– Erasing a title (page 65).
– Erasing multiple titles (page 67).
– Erasing a section of a title (A-B Erase) (page 66).
– Rearranging the title order (DVD-RWs (VR
mode) only) (page 70).
– Dividing a title into multiple titles (page 67).
– Combining multiple titles into one title
(page 70).
– Erasing a chapter (page 66).
z Hint
You can display the disc’s Playlist titles in the Title List
(Playlist), or the original titles in the Title List (Original).
To switch the two Title Lists, press TOOLS while a Title
List is displayed, and select “Original” or “Playlist.”
b Notes
• The Playlist title calls up data from the original titles for
playback. When an original title is used for a Playlist
title, the original title cannot be erased.
• If a message appears and indicates that the disc’s
control information is full, erase or edit unnecessary
titles.
• Playlist titles containing titles recorded with the “CopyOnce” copy protection signal cannot be dubbed or
moved (page 72).
Erasing and Editing a Title
HDD
+RW
-RWVR -RWVideo
+R
-R
This section explains the basic edit functions. Note
that editing is irreversible. To edit the HDD or
DVD-RWs (VR mode) without changing the
original recordings, create a Playlist title
(page 69).
Edit options for DVD+RWs/DVDRWs (Video mode)/DVD+Rs/DVD-Rs
-RWVideo
+R
-R
You can perform simple edits. Since Video mode
titles are actual recordings on the disc, you cannot
undo any edits you make. The edit functions
available for Video mode titles are:
– Setting protection against erasure (page 65).
– Labelling a title (page 65).
– Erasing a title (page 65).
– Erasing multiple titles (page 67).
– Erasing a section of a title (A-B Erase)
(DVD+RWs only) (page 66).
– Erasing all titles on the disc (page 68).
– Erasing titles to open up disc space (Disc Map)
(DVD+RWs and DVD-RWs (Video mode)
only) (page 68).
b Notes
• When editing a DVD+R or DVD-R, finish all editing
before finalizing the disc. You cannot edit a finalized
disc.
• The available disc space does not increase even when
you are erase titles for DVD+Rs and DVD-Rs.
• If a message appears and indicates that the disc’s
control information is full, erase or edit unnecessary
titles.
1
2
3
4
5
6
7
8
9
0
TITLE LIST
</M/m/,,
ENTER
Erasing and Editing
+RW
TOOLS
.
m
>
M
X
CHAPTER
MARK
1
CHAPTER
MARK ERASE
Press TITLE LIST.
For HDD titles or DVD-RWs in VR mode,
press TOOLS and select “Original” or
“Playlist” from the TOOLS menu to switch
the Title Lists, if necessary.
2
Select a title, and press ENTER.
The sub-menu appears.
3
Select an option, and press ENTER.
You can make the following edits to the title.
“Erase”: Erases the selected title. Select “OK”
when asked for confirmation.
“Protect”: Protects the title. Select “On” when
the Protection display appears. “ ” appears
next to the protected title. To cancel the
protection, select “Off.”
“Title Name”: Allows you to enter or re-enter
a title name (page 36).
“Set Thumbnail”: Changes the title’s
thumbnail picture that appears in the Title List
(page 34).
,continued
65
“A-B Erase”: Erases a section of the title
(page 66).
“Delete Chapter”: Erases chapter units of the
title while viewing thumbnails (see below).
“Divide”: Divides a title into two titles
(page 67).
z Hints
• You can erase multiple titles at one time (page 67), or
erase all of the titles on the disc at once (page 68).
• You can automatically erase titles that have already
played.
• You can label or re-label DVDs (page 38).
Erasing a section of a title
(A-B Erase)
HDD
+RW
-RWVR
You can select a section (scene) in a title and erase
it. Note that erasing scenes in a title cannot be
undone.
1
After step 2 of “Erasing and Editing a
Title,” select “A-B Erase” and press
ENTER.
The display for setting point A appears.
• To return to the beginning of the title, press
X and then press ..
b Note
DVD-RW (VR mode) playlist titles cannot be protected.
A–B Erase (Set point A)
5 Weather
Erasing a chapter (Delete Chapter)
HDD -RWVR
Thumbnails are displayed for each chapter. You
can easily select and erase a section in a title.
Note that erasing a chapter cannot be undone.
Playback point
1
After step 2 of “Erasing and Editing a
Title,” select “Delete Chapter,” and press
ENTER.
2
Select a thumbnail of the chapter using
</,, and press ENTER.
2
The display for setting point B appears.
3
Delete Selected Chapters 9 World Sports
Cancel
Reset All
• To cancel the selection, press ENTER again.
• To erase multiple chapters, repeat step 2.
• To reset all selections, select “Reset All.”
3
Select “OK,” and press ENTER.
The display asks for confirmation.
4
Select point B by pressing m/M, and
press ENTER.
The display asks for confirmation.
• To reset either point A or B, select “Change
A” or “Change B,” and go to step 2 or 3.
• To preview the title without scenes to be
erased, select “Preview” (except for
DVD+RWs).
Chapter 4(30)
0:12:45
OK
Select point A by pressing m/M, and
press ENTER.
4
Select “OK,” and press ENTER.
The scene is erased, and the display asks
whether to erase another scene.
• To continue, select “Yes,” and repeat from
step 2.
• To finish, select “No.”
Select “Yes,” and press ENTER.
z Hint
A chapter mark is inserted after the scene was erased. The
chapter mark divides the title into separate chapters on
either side of the mark.
66
b Notes
• Images or sound may be momentarily interrupted at the
point where you erase a section of a title.
• Sections shorter than five seconds may not be erased.
• For DVD+RWs, the erased section may be slightly
different from the points you selected.
Erasing multiple titles (Erase
Titles)
HDD
+RW
-RWVR -RWVideo
+R
Dividing a title (Divide)
HDD -RWVR *
If you want to dub a long title to a disc but do not
want to reduce the picture quality, divide the title
into two shorter titles. Note that dividing a title
cannot be undone.
* Only playlist titles can be divided for DVD-RW (VR
mode).
-R
1
You can select and erase more than one title at one
time using the TOOLS menu.
Press TITLE LIST.
Press TOOLS to select “Erase Titles,” and
press ENTER.
The display for selecting titles to be erased
appears.
3
Press TOOLS and select “Original” or
“Playlist” from the TOOLS menu to switch
the Title Lists, if necessary.
2
Select a title, and press ENTER.
The sub-menu appears.
3
Select “Divide,” and press ENTER.
The display for setting the dividing point
appears. The title starts to play in the
background.
• To return to the beginning of the title, press
X and then press ..
Select a title, and press ENTER.
A check mark appears in the check box next to
the selected title.
• To clear the check mark, press ENTER
again.
• To clear all of check marks, select “Reset
All.”
Divide
Erasing and Editing
1
2
Press TITLE LIST.
1 Vacation
Erase Titles
Select the titles to erase.
OK
12
Tennis
28.10
11
Travel
26.10
10
Mystry
25.10
9
World Sports
19.10
8
Family
17.10
Cancel
Reset All
4
Repeat step 3 to select all of the titles you
want to erase.
5
When you finish selecting titles, select
“OK,” and press ENTER.
The list of the titles to be erased appears for
confirmation.
• To change the selection, select “Change,”
and repeat from step 3.
6
Select “OK” and press ENTER.
The titles are erased.
4
Select the dividing point by pressing m/
M, and press ENTER.
The display asks for confirmation.
• To change the dividing point, select
“Change.”
5
Select “OK,” and press ENTER.
The display for entering the title name
appears.
• To use the same title name as before, select
“No.”
6
Select “Yes,” and press ENTER to enter a
new name.
Follow the explanations on page 36. After you
enter a new name, the title is divided in two.
,continued
67
3
Erasing all titles on the disc
HDD
1
+RW
-RWVR -RWVideo
+R
The display for selecting titles to be erased
appears.
• To cancel the selection, press ENTER again.
• To erase more titles, repeat step 3.
-R
Press TOOLS to select “Disc Info,” and
press ENTER.
Disc Map
The “Disc Information” display appears.
2
3
Select a title by pressing </,, and
press ENTER.
Select “Erase All,” and press ENTER.
2 Journey
Fri 17.9.2004 20:00 (1H00M)
SP 0.6GB
Select “OK,” and press ENTER.
All titles on the disc are erased (except the
protected titles).
Erase
Erasing titles to open up disc
space (Disc Map)
+RW
Selected title
4
Select “Erase,” and press ENTER.
The display asks for confirmation.
-RWVideo
When recording on a DVD+RW or DVD-RW
(Video mode), the recorder searches for the largest
open space and records there. Before you start,
check the disc status by using Disc Map, and erase
titles to create a space large enough for the
recording.
1
2
Cancel
Insert a disc and press TITLE LIST.
5
Select “OK,” and press ENTER.
The selected titles are erased, freeing up disc
space.
• To change the selection, select “Change.”
Creating chapters manually
HDD
-RWVR
Press TOOLS to select “Disc Map,” and
press ENTER.
You can manually insert a chapter mark at any
point you like during playback or recording.
The “Disc Map” display appears.
• To check the open space, select the space by
pressing </,.
Press CHAPTER MARK at the point where you
want to divide the title into chapters.
Disc Map
Empty Title
HQ: 0H30M
LP : 1H30M
HSP: 0H45M
EP : 2H00M
SP : 1H00M
SLP: 3H00M
2.3 GB
LSP: 1H15M
SEP: 4H00M
Each time you press the button, “Marking...”
appears on the screen and the scenes to the left and
right of the mark become separate chapters.
To erase chapter marks
Erase
Cancel
• When b or B appears on either side of the
screen, you can scroll sideways by pressing
</,.
You can combine two chapters by erasing the
chapter mark during playback.
Press ./> to search for a chapter number, and
while displaying the chapter containing the
chapter mark you want to erase, press CHAPTER
MARK ERASE.
The current chapter combines with the previous
chapter.
b Notes
• When dubbing, any chapter marks you enter will be
erased.
• To insert a chapter mark manually during recording, set
“Auto Chapter” in “Features” setup to “Off.”
68
Creating and Editing a
Playlist
5
The display for setting the end point (OUT)
appears, and the title continues to play in the
background.
6
HDD -RWVR
Playlist edit allows you to edit or re-edit without
changing the actual recordings. You can create up
to 97 Playlist titles.
b Note
Once you create a Playlist title from original titles, you
will be unable to erase or edit the original titles.
Select the OUT point by pressing m/M,
and press ENTER.
The display asks for confirmation.
To reset the IN or OUT point, select “Change
IN” or “Change OUT” and repeat step 5 or 6.
To view the selected scene, select “Preview.”
7
Select “OK,” and ENTER.
The Scene List menu appears with all of the
selected scenes.
Press TITLE LIST.
Total duration of
the selected scene
Press TOOLS to select “Create Playlist,”
and press ENTER.
Scene List
Total number of scenes
Total 0:13:19
Scenes 1
Create Playlist
Select a title to start capturing.
3
1
Cancel
12
Tennis
28.10
11
Travel
26.10
10
Mystry
25.10
9
World Sports
19.10
8
Family
17.10
7
Nature
15.10
Add
• To add more scenes, select “Add” and go to
step 3.
• To preview all of the captured scenes in the
listed order, select “Preview.”
8
Select the scene you want to re-edit, and
press ENTER.
The sub-menu appears.
“Move”: Changes the scene order.
“Erase”: Erases the scene. The selection is
cancelled.
“Preview”: Displays thumbnail pictures of the
scenes.
“Change IN”: Allows you to change the IN
point, and repeat from step 5.
“Change OUT”: Allows you to change the
OUT point, and repeat from step 6.
The display for setting the start point (IN)
appears. The title starts to play in the
background.
• To return to the beginning of the title, press
X and then press ..
9 World Sports
Quit
Preview
Select “Capture,” and press ENTER.
Capture(Set IN point)
World Sports
0:10:26 - 0:23:45
Select the title you want to include in the
Playlist title, and press ENTER.
The sub-menu appears.
“Capture”: Adds a section of the title to the
Playlist title as one scene.
“Capture All”: Adds the entire title to the
Playlist title as one scene. After capturing the
title, go to step 8.
4
OK
Scene List
ORIGINAL
Erasing and Editing
1
2
Select the IN point by pressing m/M,
and press ENTER.
9
When you finish editing the Scene List,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select “Enter”
(page 36).
10 Select “OK” to use the default name, and
press ENTER.
,continued
69
2
To play the Playlist title
Press TOOLS while the Title List menu is turned
on. Then, select “Playlist” and press ENTER.
When the Title List (Playlist) menu appears, select
a title and press H.
Press TOOLS to select “Combine,” and
press ENTER.
The display for selecting titles appears.
3
Select a title, and press ENTER.
A number indicating the order in which you
selected the title appears.
To cancel the selection, press ENTER again.
z Hint
When a Playlist title is created, the IN and OUT points
will become chapter marks, and each scene will become
a chapter.
Combine
Select the titles to combine.
4
1
b Note
3
The picture may pause when the edited scene is played.
Moving a Playlist title (Change
Order)
4
You can change the Playlist title order within the
Title List (Playlist).
5
Cruising
Cancel
25. 9
2
Journey
17. 9
1
Vacation
15. 9
Reset All
Repeat step 3 to select all of the titles you
want to combine.
Select “OK,” and press ENTER.
The list of titles to be combined appears.
To change the selection, select “Change” and
go to step 3.
Press TITLE LIST to turn on the Title List
(Playlist) menu.
Combine
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2
25. 9
To cancel all of the selections, select “Reset
All.”
-RWVR
1
OK
Yacht
Combine the titles in the following order.
1
4
Yacht
25. 9
2
3
Cruising
25. 9
Select the title you want to move, and
press ENTER.
The sub-menu appears.
3
OK
Select “Change Order,” and press ENTER.
6
Change Order
1
Vacation
15.9
Cancel
4
Journey
17.9
Select a new location for the title by
pressing M/m, and press ENTER.
The title moves to the new location.
Combining multiple Playlist titles
(Combine)
HDD -RWVR
1
Cancel
Select “OK,” and press ENTER.
The display for selecting a title name from
among the selected titles appears.
To enter a new name, select “Enter Text,” and
follow the explanations on page 36.
To change the selection, select “Change” and
go to step 3.
Where do you want to move this title?
2
Change
7
Select a name, and press ENTER.
The titles are combined.
b Note
When the number of chapters in the title to be combined
exceeds the limit, the chapters at the end are combined
into a single chapter.
Press TITLE LIST to turn on the Title List
(Playlist) menu.
Dividing a Playlist title (Divide)
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
HDD -RWVR
You can divide a Playlist title. For operations, see
page 67.
70
z Hints
• When you dub a Playlist title, it is recorded as an
Original title.
• When dubbed from a DVD to the HDD, the picture size
and the sound types originally recorded are retained.
Dubbing (HDD y DVD)
Before Dubbing
b Notes
HDD
+RW
-RWVR -RWVideo
+R
-R
Before you start…
• Select the disc type according to your needs
(page 8). This recorder can record on various
discs.
• You cannot record both the main and sub sound
on a DVD+RW, DVD-RW (Video mode),
DVD+R, or DVD-R. For bilingual programs, set
“DVD Bilingual Rec.” to either “Main” (default)
or “Sub” in “Options” setup (page 87).
• Timer recordings and Synchro-Recording do not
start during dubbing. Before you start, check the
Timer List menu to see if there is any timer
recording due to start during dubbing.
• When “Auto Chapter” of “Features” setup is set
to “On,” chapter marks are automatically
inserted at approximately 6-minute intervals
while dubbing from the HDD to a DVD, or when
the recorder detects picture and sound changes
while dubbing from a DVD to the HDD. The
chapter marks in the dubbing source are not
retained in the dubbed title.
• For a title whose picture size (16:9 or 4:3) is
mixed:
– When dubbed from the HDD to DVD-RW
(Video mode) or DVD-R, the picture size is
determined by the setting in “DVD Rec.
Picture Size” (page 46).
– When dubbed from HDD to DVD+RW or
DVD+R, the picture size is always 4:3.
– When dubbed from HDD to DVD-RW (VR
mode), the originally recorded picture size is
retained.
About “Dub Mode”
With this recorder, the recording mode for
dubbing is displayed as “Dub Mode.” Two
dubbing method are available: High-speed
Dubbing and Rec Mode Conversion Dubbing.
Read the following and select according to the
required time, disc space, and picture quality.
Dubbing at high-speed (High-speed Dubbing)
HDD , +RW / -RWVR / -RWVideo / +R /
Dubbing (HDD y DVD)
In this section, “dubbing” refers to “copying a
recorded title on the internal hard disk drive
(HDD) to another disc, or vice versa.” You can
select to dub one title at a time (Title Dubbing –
see “Dubbing a single title (Title Dub)” on
page 73), or multiple titles all at once (Multiple
Title Dubbing – see “Dubbing multiple titles (Dub
Selected Titles)” on page 74).
Before you start, read the following precautions,
which are common to both dubbing methods. To
record from equipment connected to the LINE IN
jacks, see “Recording from connected equipment
without a timer” on page 50.
• To play a dubbed disc on other DVD equipment,
finalize the disc (page 39).
• The recorder may not function as described depending
on the disc status. Follow the instructions that appear on
the screen.
• You cannot dub from DVD VIDEOs to the HDD.
• Thumbnails that you have set for the originally
recorded title (page 34) will not be retained in the
dubbed title.
-R
Allows you to dub what you have stored in the
HDD to a high-speed DVD (8x-speed
DVD+RWs/6x-speed DVD-RWs/16x-speed
DVD+Rs/16x-speed DVD-Rs, or slower versions
of each disc type), without changing the recording
mode.
Set “Dub Mode” to “Fast” in “Title Dub” or “Dub
Selected Titles” display (page 73). You cannot
select “Fast” when titles that cannot be dubbed at
high speed are selected (such as the titles displayed
in “Notes” below). The minimum required time is
as follows (approximate).
,continued
71
Required times for High-speed Dubbing from
HDD to DVD (for 60-minute programme)*1
Speed*2 6x
6x*3
8x*4
8x*4
Highspeed
DVD+
RW
Highspeed
DVD-R
High- DVD+R
speed (Double
DVD+R Layer)
2.4x
+R
/
-R
Allows you to dub from the HDD to a DVD or vice
versa, in a dubbing mode that differs from the
original recordings. For example, when you dub
an HQ title (data size is large) in SP mode, you can
reduce the data size, saving more titles using less
space.
Select a mode different from the original recording
in “Dub Mode” in the steps of “Dubbing a single
title (Title Dub)” on page 73 or “Dubbing multiple
titles (Dub Selected Titles)” on page 74.
When a title recorded to HDD in HQ or HQ+ mode
is converted to another mode, the recorder
automatically assigns an appropriate bit rate, thus
retaining the original picture quality as much as
possible.
Rec.
mode
Highspeed
DVDRW
HQ
10 min. 10 min. 8 min. 8 min. 25 min.
HSP
6 min. 6 min. 5 min. 5 min. 16 min.
40 sec. 40 sec.
40 sec.
SP
5 min. 5 min. 3 min. 3 min. 12 min.
45 sec. 45 sec. 30 sec.
LSP
4 min. 4 min. 3 min. 3 min. 10 min.
LP
3 min. 3 min. 2 min. 2 min. 8 min.
20 sec. 20 sec. 30 sec. 30 sec. 20 sec.
EP
2 min. 2 min. 2 min. 2 min. 6 min.
30 sec. 30 sec.
15 sec.
SLP
1 min. 60
60
1 min. 60
40 sec. min.*5 15 sec. min.*5 min.*5
The picture quality will not improve even if a title is
converted to a recording mode of better picture quality.
SEP
1 min. 60
56 sec. 60
60
15 sec. min.*5
min.*5 min.*5
Dubbing restriction
*2
*3
*4
*5
The values in the above table are for reference only.
Actual times for dubbing also require time for creating
disc’s control information and other data.
This is the maximum recording speed of this recorder.
The value may vary depending on the disc condition.
Also, this recorder may be unable to record at the
maximum speed for discs that support recording
speeds exceeding the maximum value.
The maximum drive speed of this recorder is 6x when
using 6x-speed or faster DVD+RWs.
The maximum drive speed of this recorder is 8x when
using 8x-speed or faster DVD+Rs/DVD-Rs.
High-speed dubbing is not available when dubbing
titles recorded in SLP and SEP mode to DVD+RWs
and DVD+Rs.
b Notes
• High-speed Dubbing is not available for the following
titles:
– Titles recorded in HQ+.
– Titles that contain both main and sub sounds (except
DVD-RWs (VR mode)).
– Titles recorded in mixed picture size (4:3 and 16:9
etc.), (except DVD-RWs (VR mode)).
• When dubbed to a DVD-RW (Video mode)/
DVD+RW/DVD+R/DVD-R, remnants of edited titles
may remain on the disc. If you edit a title, use the Rec
Mode Conversion Dubbing method. This will smooth
out the pauses between the scenes.
• When dubbing to a DVD+R DL disc, the video may be
momentarily interrupted at the point where the layers
switch.
b Note
You cannot dub movies and other DVD Videos to
the HDD. Also, when dubbing from a DVD to the
HDD, a gray, blank screen will be recorded for
scenes that contain a copy protection signal.
Copy
protection
signals
Copy-Free
(No copy
protection
signal)
Copy-Once
Dubbing
HDD
HDD
+RW
-RWVR
,
*1
72
Rec Mode Conversion Dubbing
HDD n +RW / -RWVR / -RWVideo /
-RWVideo
+R
,
-RWVR
,
-R
*
* CPRM-compatible DVD-RWs (VR mode) only
CPRM (Content Protection for Recordable Media) is a
coding technology that protects copyrights for images.
Move
HDD , -RWVR
Titles containing “Copy-Once” copy protection
signals can be moved only from HDD to DVDRW (VR mode)* (after the title is moved, the
original title in the HDD is erased). The “Move”
function is performed using the same procedure as
dubbing (page 73). Titles containing “CopyOnce” copy protection signals are indicated with
.
Dubbing
HDD
+RW
-RWVR -RWVideo
+R
-R
Dubbing a single title (Title Dub)
1
Insert the DVD that you are going to dub to
or from.
b Notes
• The following titles in the HDD cannot be moved.
– Protected titles
– Playlist titles
– Original titles referenced from the playlist
• If the move operation is stopped before completion, the
title in the HDD is not erased.
2
3
Press HDD or DVD to select the source.
4
Select a title, and press ENTER.
* CPRM-compatible DVD-RWs (VR mode) only.
5
Press TITLE LIST to turn on the Title List
menu.
The sub-menu appears.
The display for selecting the dubbing mode
appears.
If a title with
(page 73) is selected in the
title list, a confirmation screen is displayed.
To “Move,” select “Yes.”
Title Dub
2.0GB
Dubbing (HDD y DVD)
Select “Dubbing,” and press ENTER.
2.6GB
This title will be dubbed. Set the dub mode.
1 World Cup Final
Dub Mode
SP 2.0GB
Rec Mode: SP
Start
Cancel
A Size of the title (approximate)
B Direction of dubbing
C Available space on the disc to be
dubbed (approximate)
D Information about the title to be dubbed
E Dubbing mode and the space that
remains after dubbing (approximate)
6
Select “Dub Mode.”
,continued
73
7
Select a dubbing mode by pressing M/m.
Fast*
HQ
SEP
HSP
SLP
SP
EP
LSP
LP
* Appears when High-speed Dubbing is available
for the title (page 71).
8
Select “Start,” and press ENTER.
The dubbing indication appears in the front
panel display (page 35).
To automatically adjust the dubbing mode
(Auto Dub Mode)
If there is not enough available space on the target
disc, the recorder automatically selects a dubbing
mode with lower picture quality according to the
available space. If there is insufficient disc space
in the selected dubbing mode, the following
display appears after step 8.
Dubbing multiple titles (Dub
Selected Titles)
A maximum of 30 selected titles can be dubbed at
once. You can select the dubbing mode for each
title.
1
Insert the DVD that you are going to dub to
or from.
2
3
Press HDD or DVD to select the source.
4
Press TOOLS to select “Dub Selected
Titles,” and press ENTER.
Dub Selected Titles
Cancel
5
Select “Auto Dub Mode” and press ENTER to
start dubbing. To manually select another dubbing
mode, select “Reset,” and go to step 7.
z Hints
• If disc space is still insufficient for the selected dubbing
mode, erase unnecessary parts of the title, or free up
disc space by erasing titles on the disc (page 68).
• You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned off.
74
Start
Cancel
4 World Tour – Asia 3
25.6
3 World Cup Final
20.6
2 World Tour – Asia 2
18.6
1 World Tour – Asia 1
11.6
Settings
Reset
Select titles in the order you want to dub,
and press ENTER.
The titles are numbered in the selected order.
To cancel the selection, press ENTER again.
If a title with
(page 73) is selected in the
title list, a confirmation screen is displayed.
To “Move,” select “Yes.”
To stop dubbing
Press TOOLS to select “Stop Dubbing,” and press
ENTER. When asked for confirmation, select
“Yes,” and press ENTER.
4.6GB
ORIGINAL
There is not enough memory for the dubbing.
Select "Auto Dub Mode" or adjust the mode.
Reset
0.0GB
Select title(s) in the order you want to dub them.
Title Dub
Auto Dub Mode
Press TITLE LIST to turn on the Title List
menu.
6
Repeat step 5 to select all of the titles you
want to dub.
To make adjustments for each of the titles,
select “Settings” (see “To adjust the settings
for each title” below). To cancel all of the
selections, select “Reset,” and go to step 5.
7
Select “Start,” and press ENTER.
The dubbing indication appears in the front
panel display (page 35).
To adjust the settings for each title
You can make detailed settings for each of the
selected titles during Multiple Title Dubbing.
1
In step 6 of “Dubbing multiple titles (Dub
Selected Titles)” on page 74, select “Settings”
and press ENTER.
The following display for making the
adjustments appears.
To re-select titles, select “Change,” and go to
step 5 of “Dubbing multiple titles (Dub
Selected Titles)” above. To have the recorder
adjust the dubbing mode so all of the selected
titles fit in, select “Auto Mode.”
To automatically adjust the dubbing mode
(Auto Dub Mode)
If there is not enough available space on the target
disc, the recorder automatically selects a dubbing
mode with lower picture quality according to the
available space. The same dubbing mode is set for
all of the titles. If disc space is insufficient for the
selected dubbing mode, the following display
appears after step 8 of “Dubbing multiple titles
(Dub Selected Titles)” on page 74.
Dub Selected Titles
There is not enough memory. Select
"Auto Dub Mode" or change the selection.
Auto Dub Mode
Dub Selected Titles
2.1GB
Adjust the settings for the dubbing here.
Change
Cancel
4.6GB
Start
World Tour – Asia 1
11.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
Cancel
2
World Tour – Asia 2
18.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
Auto mode
3
World Tour – Asia 3
25.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
4
World Cup Final
Rec Mode: SP
Change
20.6
Dub Mode: Fast 1.2GB
1 Total size of the selected titles
2 Direction of dubbing
3 Available space on the disc to be
dubbed (approximate)
Select “Auto Dub Mode” and press ENTER. If
you have selected only one title, select “OK.”
To stop dubbing
Press TOOLS to select “Stop Dubbing,” and press
ENTER. When asked for confirmation, select
“Yes,” and press ENTER.
z Hints
• You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned off.
• You can start Multiple Title Dubbing by selecting
“DUBBING” from the System Menu.
Dubbing (HDD y DVD)
1
4 Information about the title to be dubbed
(title name, original recording mode,
dubbing mode, and data size after
dubbing)
5 Order of dubbing
2
Select the title which you want to adjust, and
press ENTER.
The sub-menu appears.
“Dub Mode”: Selects the dubbing mode for
each title (page 71).
“Change Order”: Moves the title to change the
dubbing order. Press M/m to select a new
location, and press ENTER.
“Cancel”: Cancels the title selection. The title
is excluded from dubbing.
3
4
Select an option, and press ENTER.
When you finish making adjustments, select
“Start,” and press ENTER.
75
2
Press PROG +/– to select the programme
position.
Settings and Adjustments
Selected programme position
Settings - Channel Setting
Aerial Reception and
Language Settings
(Settings)
The “Settings” setup helps you to make tuner,
clock, and programme position settings for the
recorder.
1
2
3
3
BG
Normal / CATV :
Normal
Channel Set :
C2
Station Name :
CDE
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Settings - Channel Setting
4
Select “Settings,” and press ENTER.
The options of “Settings” appear. The default
settings are underlined.
To turn off the display, press SYSTEM
MENU repeatedly.
System :
BG
BG
Normal / CATV :
Normal
DK
Channel Set :
C
I3
Station Name :
AAB
L
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Channel Setting
Video
Channel List
Audio
TV Guide Page
Features
Clock
Options
Language
Easy Setup
5
BG
Select this when in West
European countries, except
those listed in “Receivable
channels” on page 77.
DK
Select this when in East
European countries.
I
Select this when in Great
Britain/Ireland.
L
Select this when in France.
Presets programme positions manually.
If some programme positions could not be set
using the “Easy Setup” function, you can set them
manually.
If there is no sound or if the picture is distorted, the
wrong tuner system may have been preset during
“Easy Setup.” Set the correct tuner system
manually in the steps below.
1
Select “Channel Setting” in “Settings,” and
press ENTER.
Settings - Channel Setting
76
Select “Normal/CATV,” and press ENTER.
Settings - Channel Setting
Channel Setting
Prog. 1
Prog. 8
Select an available TV system, BG, DK, I, or
L, and press ENTER (page 77).
SETUP
Settings
Prog. 8
Select “System,” and press ENTER.
Press SYSTEM MENU while the recorder is
in stop mode.
Select “SETUP,” and press ENTER.
System :
System :
BG
Normal / CATV :
Normal
Normal
Channel Set :
3
C
CATV
Station Name :
CDE
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 8
6
Select “Normal,” and press ENTER.
To set CATV (Cable Television) channels,
select “CATV.”
7
Select “Channel Set,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
3
C
C2
Station Name :
CDE
System :
BG
PAY - TV / CANAL+ :
Off
Normal / CATV :
Normal
Audio :
NICAM
Channel Set :
C3
Station Name :
AAB
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 8
8
9
Press M/m repeatedly until the channel you
want is displayed, then press ENTER.
The channels are scanned in the order shown
in the table below.
• If you know the number of the channel you
want, press the number buttons. For
example, for channel 5, first press “0” and
then press “5.” Then press ENTER.
Receivable channels
TV system
S1 – S20 CATV
Select “Audio,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
C5
Station Name :
CDE
PAY - TV / CANAL+ :
Off
NICAM
Audio :
NICAM
Standard
Channel coverage
BG (West European E2 - E12 VHF
Countries, except
Italia A – H VHF
those listed below)
E21 – E69 UHF
S21 – S41 HYPER
Prog. 8
S01 – S05 CATV
DK (East European
Countries)
R1 – R12 VHF
R21 – R69 UHF
S1 – S20 CATV
S21 – S41 HYPER
Normally, select this.
Standard
Select this if the sound from
NICAM broadcasts is not
clear.
S01 – S05 CATV
I (Great Britain/
Ireland)
Ireland A – J VHF
South Africa 4 – 13 VHF
B21 – B69 UHF
S1 – S20 CATV
10 Select “NICAM,” and press ENTER.
11 Select “AFT” and press ENTER.
Settings - Channel Setting
Normal / CATV :
Normal
Channel Set :
C5
Station Name :
CDE
PAY - TV / CANAL+ :
Off
Audio :
NICAM
On
AFT :
Off
S21 – S41 HYPER
S01 – S05 CATV
Prog. 8
L (France)
F2 – F10 VHF
F21 – F69 UHF
Settings and Adjustments
NICAM
B – Q CATV
S21 – S41 HYPER
On
Turns on the Auto Fine
Tuning function. Normally,
select this.
Off
Allows you to adjust the
pictures manually.
12 Select “On” to turn on AFT, and press
ENTER.
• If the Auto Fine Tuning function does not
work effectively, select “Off” and press
ENTER. When the fine tuning bar appears,
press </, to obtain a clearer picture, and
press ENTER.
• To preset another channel, repeat from step
2.
,continued
77
Station Name
Changes or enters a new station name (up to 5
characters). The recorder must receive channel
information (for instance, SMARTLINK
information) for station names to appear
automatically.
1
Select “Channel Setting” in “Settings,” and
press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
C3
Station Name :
AAB
PAY - TV / CANAL+ :
Off
Audio :
NICAM
Prog. 1
Channel List (Changing/Disabling
the channels)
Changes or disables the programme positions after
setting the channels. If any programme positions
are unused or contain unwanted channels, you can
disable them.
You can also change station names. If the station
names are not displayed, you can enter them
manually.
1
Select “Channel List” in “Settings,” and press
ENTER.
Settings - Channel List
2
3
Press PROG +/– to select the programme
position for which you want to change or enter
a station name.
Select “Station Name,” and press ENTER.
The display for entering characters appears.
2
Input Station Name
1
6
"A"
2
Back
7
"a"
3
Clear All
8
4
Space
9
Cancel
0
Finish
5
Symbol
Select “Finish,” and press ENTER.
Channel
1
C3
AAB
2
C5
FGH
3
C12
4
C21
5
C23
6
C24
Name
PQR
Press M/m to select the row containing the
programme position you want to change or
disable.
To change, press ENTER and go to step 3.
To disable, press CLEAR and go to step 5.
The disabled positions will be skipped when
you press PROG +/–.
To display other pages for programme
positions 7 to 99, press M/m repeatedly.
To enter characters, see page 36.
4
Prog
3
PAY-TV/CANAL+
Sets the PAY-TV/Canal Plus channels.
For details, see page 27.
Press M/m until the selected channel row
moves to the desired programme position.
The selected channel is inserted at the new
programme position.
Settings - Channel List
4
5
Prog
Channel
Name
1
C3
AAB
2
C12
3
C21
4
C5
5
C23
6
C24
FGH
PQR
Press ENTER to confirm the setting.
To change or disable the programme position
of another station, repeat from step 2.
b Note
Be sure to correctly select the programme position you
want to disable. If you disable the wrong programme
position by mistake, you need to reset that channel
manually.
78
4
TV Guide Page
Some broadcast systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time,
etc.) are stored day by day. A TV guide page
corresponds to each day of the week. When
recording a programme, the recorder
automatically takes the programme name from the
Teletext pages and stores it as the title name. The
TV guide page numbers depend entirely on the
broadcast itself and may be subject to change. If
so, you may have to set those TV guide page
numbers manually in the TV Guide Page menu.
* Not available in some areas.
Select “TV Guide Page” in “Settings,” and
press , or ENTER.
The TV Guide Page menu appears.
2
Select the programme position for which you
want to set or change the TV guide page by
pressing PROG +/–.
• The TV guide page numbers (Example:
P301) appear automatically when the
recorder detects them.
Settings - TV Guide Page
Sun
P 301
Mon
P 302
Tue
P 303
Wed
P 304
Thu
P 305
Fri
P 306
Sat
P 307
Prog. 4
• If no page numbers are detected (P000), you
have to set the appropriate TV guide page
number manually.
Settings - TV Guide Page
3
Sun
P 000
Mon
P 000
Tue
P 000
Wed
P 000
Thu
P 000
Fri
P 000
Sat
P 000
To set or change another TV guide page
number, repeat steps 3 and 4 above.
z Hint
To view Teletext information on your TV screen during
a broadcast, switch to your TV’s tuner by pressing
t TV/VIDEO.
b Notes
• In step 4 above, enter “000” if you do not want to use
the TV guide page number for automatic labelling. The
recorder will instead store a default title name
(programme position, start time - stop time).
• Refer to the Teletext information on your TV screen to
obtain the TV guide page number with programme
titles and their start times.
• If the Teletext TV guide has a page which always
shows the programmes for the current day, this page
should be input for all days.
• If you start recording more than three minutes before
the programme is scheduled to start, the correct label
information may not be transferred.
• Note that this function may not work correctly with
programmes broadcast from some stations.
• If the broadcast system updates the Teletext
information at the moment recording starts, the title
label may not correspond to the recorded programme.
In this case, you may have to manually enter the correct
title (page 36).
Clock
Prog. 4
Auto Adjust
Turns on the Auto Clock Set function when a channel
in your local area broadcasts a time signal.
Select the TV guide page number you want to
modify, and press ENTER.
Settings - TV Guide Page
1
Select “Clock” in “Settings,” and press
ENTER.
2
Select “Auto Adjust,” and press ENTER.
Settings - Clock
Auto Adjust :
Prog. 4
Present Time :
Sun
PP 000
0 0
Mon
P 000
Tue
P 000
Wed
P 000
Thu
P 000
Fri
P 000
Sat
P 000
Settings and Adjustments
1
Press the number buttons or </M/m/, to
enter the TV guide page number, and press
ENTER to confirm the setting.
• If you make a mistake, press CLEAR to reenter the correct number.
Off
Thu
1
1. 1. 2004. 21:39
0
3
Select “On,” and press ,.
,continued
79
4
Press M/m repeatedly until the programme
position of the station that carries a time signal
appears, and press ENTER.
Language
OSD (On-Screen Display)
Settings - Clock
On
Auto Adjust :
Present Time :
Thu
1
Switches the display language on the screen.
1. 1. 2004. 21:39
DVD Menu (DVD VIDEO only)
• If the recorder does not receive a time signal
from any station, “Auto Adjust” returns to
“Off” automatically and the menu for setting
the clock manually appears on the screen.
z Hint
If you set “Auto Adjust” to “On,” the Auto Clock Set
function is activated whenever the recorder is turned off.
b Note
The Auto Clock Set function does not work while the
recorder is standing by for Synchro-Recording.
To set the clock manually
If the Auto Clock Set function did not set the clock
correctly for your local area, try another station for
the Auto Clock Set function or set the clock
manually.
1
Select “Clock” in “Settings,” and press
ENTER.
2
Select “Auto Adjust,” and press ENTER.
Settings - Clock
Off
Auto Adjust :
Present Time :
3
4
Thu
1
1. 1. 2004. 21:39
Select “Off,” and press ENTER.
Select “Present Time,” and press ENTER.
Clock - Present Time
Set the time and date manually.
Sat 1
5
1
2005
0 : 00
Press M/m to set the day, and press ,.
Set the month, year, hour, and minutes in
sequence. Press </, to select the item to be
set, then press M/m to set the numbers. The
day of the week is set automatically.
To change the numbers, press < to return to
the item to be changed, and press M/m.
6
80
Press ENTER to start the clock.
Switches the language for the DVD menu.
Audio (DVD VIDEO only)
Switches the language of the sound track.
When you select “Original,” the language given
priority in the disc is selected.
Subtitle (DVD VIDEO only)
Switches the language of the subtitles recorded on
the disc.
When you select “Audio Follow,” the subtitle
language changes according to the language you
selected for the sound track.
z Hint
If you select “Others” in “DVD Menu,” “Subtitle,” or
“Audio,” select and enter a language code from
“Language Code List” on page 104 using the number
buttons.
b Note
If you select a language in “DVD Menu,” “Subtitle,” or
“Audio” that is not recorded on the DVD VIDEO, one of
the recorded languages will be automatically selected.
Video Settings (Video)
Video settings will adjust items related to the
image, such as size and colour.
Choose the settings according to the type of TV,
tuner, or decoder connected to the DVD recorder.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
16:9
4:3 Letter Box
4:3 Pan Scan
Select “Video,” and press ENTER.
The “Video” setup appears with the following
options. The default settings are underlined.
b Note
Depending on the disc, “4:3 Letter Box” may be selected
automatically instead of “4:3 Pan Scan” or vice versa.
SETUP
TV Type :
16 : 9
Video
Pause Mode :
Auto
Audio
Component Out :
Off
Features
Progressive Mode :
Auto
Options
Scart Setting
Line4 Input :
Pause Mode (HDD/DVDs only)
Selects the picture quality in pause mode.
Auto
The picture, including subjects
that move dynamically, is output
with no jitter. Normally select this
position.
Frame
The picture, including subjects
that do not move dynamically, is
output in high resolution.
Video
Easy Setup
TV Type
Sets the picture size when playing back a title
recorded from 16:9 size video (page 46) or a 16:9
size commercial DVD video.
Select the playback picture size according to the
type of connected TV (wide-screen/wide mode
TV or conventional 4:3 screen TV).
16:9
Select this when connecting to a
wide-screen TV or TV with a wide
mode function.
4:3 Letter
Box
Select this when connecting to a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the screen.
4:3 Pan
Scan
Select this when connecting to a
4:3 screen TV. Automatically
displays a wide picture on the
entire screen and cuts off the
portions that do not fit.
Settings and Adjustments
Settings
Component Out
Selects whether or not to output video signals
from the COMPONENT VIDEO OUT jacks.
On
Outputs the component video
signals. Select this when you want
to view progressive signals.
Off
Outputs no signals.
b Notes
• When you set “Line1 Output” to “RGB,” you cannot
set “Component Out” to “On.”
• When you connect the recorder to a monitor or
projector via only the COMPONENT VIDEO OUT
jacks, do not select “Off.” If you select “Off” in this
case, the picture may not appear.
,continued
81
Progressive Mode
DVD software can be divided into two types: film
based software and video based software. Video
based software is derived from TV, such as
dramas and sit-coms, and displays images at 30
frames/60 fields (25 frames/50 fields) per second.
Film based software is derived from film and
displays images at 24 frames per second. Some
DVD software contains both Video and Film.
In order for these images to appear natural on your
screen when output in PROGRESSIVE mode (50
or 60 frames per second), the progressive video
signal needs to be converted to match the type of
DVD software that you are watching.
You can fine-tune the progressive 525p/625p
video signal that is output when you press
PROGRESSIVE (“PROGRESSIVE” lights up).
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO OUT
jacks (page 14).
Auto
Video
Automatically detects the software
type (Film-based or Video-based)
and selects the appropriate
conversion mode. Normally select
this position.
Fixes the conversion mode to the
mode for Video-based software.
Scart Setting
Sets the method of inputting/outputting signals
from the SCART jacks on the rear panel of the
recorder. Select an option for each of the items
below according to the combination of jacks and
methods that you are going to use.
Line1 Output
Selects a method of outputting video signals for
the LINE 1 – TV jack.
RGB
Outputs RGB signals.
Video
Outputs video signals.
S Video
Outputs S-video signals.
b Notes
• If your TV does not accept S-video or RGB signals, no
picture appears on the TV screen even if you select “S
Video” or “RGB.” See the instructions supplied with
your TV.
• You cannot select “RGB” when “Component Out”
above is set to “On.”
• SMARTLINK is available only when “Video” is
selected.
82
Line3 Input
Selects a method of inputting video signals for the
LINE 3/DECODER jack. The picture will not be
clear if this setting does not match the type of
video input signal.
Video/
RGB
Inputs video signals or RGB
signals.
Decoder
Select this when connecting to a
PAY-TV/Canal Plus decoder.
S Video
Inputs S-video signals.
Line3 Output
Selects a method of outputting video signals for
the LINE 3/DECODER jack.
Video
Outputs video signals.
S Video
Outputs S-video signals.
Line4 Input
Selects a method of inputting video signals for the
LINE 4 IN jack on the rear panel of the recorder.
Video
Inputs video signals.
S Video
Inputs S-video signals.
Audio Settings (Audio)
The “Audio” setup allows you to adjust the sound
according to the playback and connection
conditions.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Audio,” and press ENTER.
The “Audio” setup appears with the following
options. The default settings are underlined.
Audio DRC (Dynamic Range Control) (DVDs
only)
Makes the sound clear when the volume is turned
down when playing a DVD that conforms to
“Audio DRC.” This affects the output from the
following jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
– DIGITAL OUT (OPTICAL or COAXIAL) jack
only when “Dolby Digital” is set to “D-PCM”
(page 84).
Standard
Normally select this position.
TV Mode
Makes low sounds clear even if
you turn the volume down.
Wide
Range
Gives you the feeling of being at a
live performance.
SETUP
Settings
Audio ATT :
Off
Video
Audio DRC :
Standard
Audio
Downmix :
Dolby Surround
Features
Audio Connection
Easy Setup
Audio ATT (attenuation)
If the playback sound is distorted, set this item to
“On.” The recorder reduces the audio output level.
This function affects the output of the following
jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
On
Select this when the playback
sound from the speakers is
distorted.
Off
Normally select this position.
Switches the method for mixing down to two
channels when you play a DVD which has rear
sound elements (channels) or is recorded in Dolby
Digital format. For details on the rear signal
components, see “4. Displaying the Playing Time
and Play Information” on page 34. This function
affects the output of the following jacks:
– LINE 2 OUT R-AUDIO-L jacks
– LINE 1 – TV jack
– LINE 3/DECODER jack
– DIGITAL OUT (OPTICAL or COAXIAL) jack
when “Dolby Digital” is set to “D-PCM”
(page 84).
Dolby
Surround
Normally select this position.
Multi-channel audio signals are
output to two channels for
enjoying surround sounds.
Normal
Multi-channel audio signals are
downmixed to two channels for
use with your stereo.
,continued
Settings and Adjustments
Downmix (DVDs only)
Options
83
Audio Connection
The following setup items switch the method of
outputting audio signals when you connect a
component such as an amplifier (receiver) with a
digital input jack.
For connection details, see “Step 4: Connecting
the Audio Cords” on page 17.
Select “Dolby Digital,” “MPEG,” “DTS,” and
“48kHz/96kHz PCM” after setting “Digital Out”
to “On.”
If you connect a component that does not accept
the selected audio signal, a loud noise (or no
sound) will come out from the speakers, and may
affect your ears or cause speaker damage.
1
• DTS (DVD VIDEO only)
Selects whether or not to output DTS signals.
On
Select this when the recorder is
connected to an audio component
with a built-in DTS decoder.
Off
Select this when the recorder is
connected to an audio component
without a built-in DTS decoder.
• MPEG (DVD VIDEO only)
Selects the type of MPEG audio signal.
PCM
Select this when the recorder is
connected to an audio component
without a built-in MPEG decoder.
If you play MPEG audio sound
tracks, the recorder outputs stereo
signals via the DIGITAL OUT
(COAXIAL) jack.
MPEG
Select this when the recorder is
connected to an audio component
with a built-in MPEG decoder.
Select “Audio Connection” in “Audio,” and
press ENTER.
Audio - Audio Connection
Digital Out :
On
Dolby Digital :
2
3
4
D-PCM
MPEG :
PCM
DTS :
Off
48kHz/96kHz PCM :
48kHz/16bit
Select “Digital Out,” and press ENTER.
On
Normally select this position.
Off
The influence of the digital
circuit upon the analogue
circuit is minimal.
Select “On,” and press ENTER.
Set the digital output signal.
• Dolby Digital (HDD/DVDs only)
Selects the type of Dolby Digital signal.
84
D-PCM
Select this when the recorder is
connected to an audio component
lacking a built-in Dolby Digital
decoder. The surround effects of
output signals are determined by
the “Downmix” setting item in
“Audio” setup.
Dolby
Digital
Select this when the recorder is
connected to an audio component
with a built-in Dolby Digital
decoder.
• 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/
16bit
The DVD video audio signal is
converted to 48kHz/16bit and
output.
96kHz/
24bit
All signals containing 96kHz/
24bit are output without
conversion. However, the signals
are output at 48kHz/16bit if
copyright-protected signals are
contained.
b Notes
• “48kHz/96kHz PCM” setting has no effect when audio
signals are output from the LINE 2 OUT (R-AUDIOL) jacks. If the sampling frequency is 96kHz, signals
are simply converted to 96kHz analog signals and
output.
• When you use the DIGITAL OUT (COAXIAL) jack to
listen to MPEG audio signals and set “MPEG” to
“MPEG” in “Audio” setup, no sound will come from
your speakers if you select one of the TVS modes.
b Note
Recording and Parental
Control Settings (Features)
The actual chapter mark interval may vary depending on
the amount of information contained in the video to be
recorded.
Parental Control (DVD VIDEO only)
The “Features” setup allows you to adjust
recording and parental control settings.
1
2
3
Press SYSTEM MENU while the recorder is
in stop mode.
Playback of some DVD VIDEOs can be limited
according to a predetermined level, such as the age
of the users. Scenes may be blocked or replaced
with different scenes.
1
Select “SETUP,” and press ENTER.
Select “Features,” and press ENTER.
The “Features” setup appears with the
following options. The default settings are
underlined.
Select “Parental Control” in “Features,” and
press ENTER.
• If you have not entered a password, the
display for registering a new password
appears.
Features - Parental Control
Enter a new password.
OK
SETUP
TV Direct Rec :
On
Video
Auto Chapter :
On
Audio
Parental Control
Features
Synchro Rec
Record to HDD
Options
HQ Setting
HQ
Colour System
PAL
Screen Saver
On
Easy Setup
Cancel
• When you have already registered a
password, the display for entering the
password appears.
Features - Parental Control
Enter your password.
TV Direct Rec (HDD/DVD+RW/DVD-RW/
DVD+R/DVD-R only)
Settings and Adjustments
Settings
OK
Cancel
On
Allows you to easily record what
you are watching on the TV using
SMARTLINK.
Off
Turns off the TV Direct Rec
function.
2
Enter your four-digit password using the
number buttons, then select “OK” and press
ENTER.
Features - Parental Control
Auto Chapter
Selects whether to automatically divide a
recording (a title) into chapters during recording
or dubbing.
On
For the HDD or a DVD-RW (VR
mode), the recorder detects
changes in the picture and sound
and automatically inserts chapter
marks.
For other recordable discs, the
recorder inserts chapter marks at
approximately 6-minute intervals.
Off
No chapter mark is inserted.
Level :
Off
Standard :
USA
Password
,continued
85
3
Select “Standard,” and press , or ENTER.
The selection items for “Standard” are
displayed.
Features - Parental Control
4
5
Level :
Off
Standard :
USA
USA
Password
Others
Select a geographic area as the playback
limitation level, and press ENTER.
The area is selected.
• When you select “Others,” press the number
buttons to select and enter an area code in
the table (page 104). Then select “OK” and
press ENTER.
Select “Level,” and press ENTER.
The selection items for “Level” are displayed.
Features - Parental Control
Level :
Off
Standard :
8
Password
7
6
Synchro Rec
Selects the recording destination used for
Synchro-Recording (page 49).
Record to
HDD
Records to the HDD.
Record to
DVD
Records to DVDs.
HQ Setting (HDD only)
Selects the HQ mode used for recording on the
HDD (page 41).
HQ+
Records in higher quality
(approximate 15 Mbps).
HQ
Records in the standard HQ mode.
Colour System
Selects the colour system when playing VIDEO
CDs (including Super VIDEO CDs).
5
4
The lower the value, the stricter the limitation.
Discs rated higher than the selected level will
be restricted.
6
Select the level, and press ENTER.
The Parental Control setting is complete.
To cancel the Parental Control setting for the
disc, set “Level” to “Off” in step 6.
To change the password, select “Password” in
step 3, and press ENTER. When the display
for registering a password appears, enter a
new four-digit password using the number
buttons, then select “OK” and press ENTER.
b Notes
• If you forget your password, you will have to reset it by
selecting “Parental Control” of “Factory Setup” in
“Options” setup (page 88).
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
recorder.
• Depending on the disc, you may be asked to change the
Parental Control level while playing the disc. In this
case, enter your password, then change the level.
86
PAL
Plays a disc in PAL colour system.
NTSC
Plays a disc in NTSC colour
system.
Screen Saver
The screen saver image appears when you do not
use the recorder for more than 10 minutes while an
on-screen display, such as the System Menu, is
displayed on your TV screen. The screen saver
image helps prevent your display device from
becoming damaged (ghosting).
On
Turns on the screen saver function.
Off
Turns off the function.
b Note
Disc and Remote Control
Settings/Factory Settings
(Options)
The “Options” setup allows you to set up other
operational settings.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Options,” and press ENTER.
The “Options” setup appears with the
following options. The default settings are
underlined.
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Normal
Options
Power Save :
Off
Auto Display :
On
Command Mode :
DVD3
Easy Setup
Factory Setup
DVD Bilingual Rec. (for all recordable discs
except DVD-RW in VR mode)
Selects the sound to be recorded on the recordable
disc. This setting is not necessary when recording
on DVD-RWs (VR mode) that record both the
main and sub sounds.
Main
Records the main sound for the
bilingual programme.
Sub
Records the sub sound for the
bilingual programme.
Dimmer
Adjusts the lighting of the front panel display.
Normal
Bright lighting.
Power
Save
Low lighting. Turns off the
lighting when the power is off.
b Note
When “Power Save” in “Options” setup is set to “On,”
the front panel display is turned off during standby
regardless of this setting.
Format DVD-RW (DVD-RW only)
Power Save
The recorder automatically starts formatting in
VR mode or Video mode, whichever is selected
below, when a new, unformatted DVD-RW is
inserted.
Selects whether this recorder is in power save
mode when the power is turned off (standby).
VR
Automatically formats the disc in
VR mode.
Video
Automatically formats the disc in
Video mode.
On
Sets to power save mode. The
front panel display is off when the
recorder is in standby.
Off
Does not set to power save mode.
Normally, select this.
Settings and Adjustments
SETUP
Settings
If you set the recording mode to be changed while
dubbing from a DVD to the HDD, the sound recorded in
the source (DVD) is applied regardless of this setting.
b Notes
HDD Bilingual Rec. (HDD only)
Selects the sound to be recorded on the HDD.
Main
Records the main sound for the
bilingual programme.
Sub
Records the sub sound for the
bilingual programme.
Main+Sub
Records the main and sub sounds
for the bilingual programme.
• Power Save mode does not function in the following
cases, even when “Power Save” is set to “On”.
– Synchro Recording is set.
– there is a timer setting with “PDC/VPS” set to “On”
in the Timer List.
• The SMARTLINK features are not available when
“Power Save” is set to “On.”
,continued
87
Auto Display
On
Automatically displays
information on the screen when
the recorder is turned on, etc.
Off
Displays information only when
DISPLAY is pressed.
Command Mode
Changes the Command Mode of the recorder if
other DVD equipment is assigned the same
Command Mode. Be sure to match the Command
Mode switch on the remote to the setting made
here. For details, see “If you have a Sony DVD
player or more than one Sony DVD recorder” on
page 21.
Easy Setup
(Resetting the Recorder)
Select this to run the “Easy Setup” programme.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Easy Setup,” and press ENTER.
SETUP
Settings
Video
Audio
DVD1
DVD2
DVD3
Select this if the default Command
Mode conflicts with other DVD
equipment.
Select this if the default Command
Mode conflicts with other DVD
equipment.
The default Command Mode of
the recorder.
Factory Setup
Allows you to select the setup settings by group,
and return them to their default settings. Note that
all of your previous settings will be lost.
88
1
Select “Factory Setup” in “Options,” and
press , or ENTER.
The display for selecting a group of settings
appears.
2
Select the group of settings you want to return
to default from “Settings,” “Video,” “Audio,”
“Features,” “Options,” “Parental Control,”
and “All,” and press , or ENTER.
3
Select “Start,” and press ENTER.
The selected settings return to their default
settings.
4
Press ENTER when “Finish” appears.
Features
Options
Easy Setup
4
5
6
Easy Setup
Press ENTER.
Select “Start.”
Follow the instructions for “Easy Setup”
(page 22) from step 2.
Additional Information
Troubleshooting
If you experience any of the following difficulties
while using the recorder, use this troubleshooting
guide to help remedy the problem before
requesting repairs. Should any problem persist,
consult your nearest Sony dealer.
Power
The power does not turn on.
, Check that the mains lead is connected securely.
Picture
There is no picture.
Re-connect all connecting cords securely.
The connecting cords are damaged.
Check the connection to your TV (page 13).
Switch the input selector on your TV (such as to
“VCR”) so that the signal from the recorder
appears on the TV screen.
, Check that “Scart Setting” in “Video” setup is set
to the appropriate item that conforms to your
system (page 82).
, If you connect the recorder to your TV via only
the COMPONENT VIDEO OUT jacks, set
“Component Out” in “Video” setup to “On”
(page 81).
, This recorder cannot record NTSC signals.
TV programme reception does not fill the
screen.
, Set the channel manually in “Channel Setting” in
“Settings” setup (page 76).
, Select the correct source using the INPUT
SELECT button, or select a channel of any TV
programme using the PROG +/– buttons.
TV programme pictures are distorted.
, Reorient the TV aerial.
, Adjust the picture (see the TV’s instruction
manual).
, Place the recorder and TV farther apart.
, Place the TV and any bunched aerial cables
farther apart.
, The RF cable is connected to the AERIAL OUT
jack on the recorder. Connect the cable to the
AERIAL IN jack.
Additional Information
,
,
,
,
, You have set the recorder to progressive format
(the PROGRESSIVE indicator lights up) even
though your TV cannot accept the progressive
signal. In this case, press PROGRESSIVE until
the progressive indicator turns off.
, Even if your TV is compatible with progressive
format (525p/625p) signals, the image may be
affected when you set the recorder to progressive
format. In this case, press PROGRESSIVE so
that the PROGRESSIVE indicator turns off and
the recorder is set to normal (interlace) format.
, You are playing a DVD recorded in a colour
system that is different from your TV.
, Noises may appear in the pictures recorded on
the HDD, which is due to the characteristics of
HDD, and is not a malfunction.
TV channels cannot be changed.
Picture noise appears.
, If the picture output signal from your recorder
passes through your VCR to get to your TV, or if
you are connected to a combination TV/VIDEO
player, the copy-protection signal applied to
some DVD programmes could affect picture
quality. If you still experience this problem even
when you connect your recorder directly to your
TV, try connecting your recorder to your TV’s S
VIDEO input.
, The channel is disabled (page 78).
, A timer recording started, which changed the
channels.
,continued
89
The picture from equipment connected to the
recorder’s input jack does not appear on the
screen.
, If the equipment is connected to the LINE 1 – TV
jack, select “L1” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 2 IN
jacks, select “L2” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 4 IN
jacks, select “L4” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 3/
DECODER jack, select “L3” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
, When an S video cable is connected to the
recorder’s LINE 4 IN jack, set “Line4 Input” in
“Video” setup to “S Video” (page 82).
Sound
There is no sound.
, Re-connect all connections securely.
, The connecting cord is damaged.
, The input source setting on the amplifier or the
connection to the amplifier is incorrect.
, The recorder is in reverse play, fast-forward,
slow motion, or pause mode.
, If the audio signal does not come through the
DIGITAL OUT (OPTICAL or COAXIAL)
jacks, check the “Audio” setup settings
(page 83).
Sound distortion occurs.
, Set “Audio ATT” in “Audio” setup to “On”
(page 83).
Sound is noisy.
The playback picture or TV programme from
the equipment connected through the recorder
is distorted.
, If the playback picture output from a DVD
player, VCR, or tuner goes through your recorder
before reaching your TV, the copy-protection
signal applied to some programmes could affect
picture quality. Disconnect the playback
equipment in question and connect it directly to
your TV.
The picture does not fill the screen.
, Set “TV Type” in “Video” setup in accordance
with the screen size of your TV (page 81).
The picture does not fill the screen, even
though the picture size is set in “TV Type” in
“Video” setup.
, The picture size of the title is fixed.
The picture is black and white.
, Check that “Line1 Output” of “Scart Setting” in
“Video” setup is set to the appropriate item that
conforms to your system (page 82).
, If you are using a SCART cord, be sure to use
one that is fully wired (21 pins).
90
, When playing a CD with DTS sound tracks,
noise will come from the LINE 2 OUT RAUDIO-L jacks, LINE 1 – TV jack, or LINE 3/
DECODER jack (page 55).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“Audio DRC” in “Audio” setup to “TV Mode”
(page 83).
, Set “Audio ATT” in “Audio” setup to “Off”
(page 83).
, One of the TVS effects is selected (page 54).
An alternate audio track cannot be recorded.
, When recording from connected equipment, set
“Line Audio Input” in TOOLS menu to
“Bilingual” (page 50).
, Multilingual tracks (main and sub) cannot be
recorded on DVD+RWs, DVD-RWs (Video
mode), DVD+Rs, or DVD-Rs. To record the
language, select “Main” or “Sub” of “DVD
Bilingual Rec.” in “Options” setup before
recording (page 87). To record both the main and
sub sounds, record on a DVD-RW (VR mode).
, Any discs other than the HDD or DVD-RWs
(VR mode) cannot be used for recording both
main and sub sounds. To record on the HDD, set
“HDD Bilingual Rec.” in “Options” setup to
“Main+Sub” (page 87).
, If you have connected an AV amplifier to the
DIGITAL OUT (OPTICAL or COAXIAL) jacks
and want to change the audio track for a DVDRW (VR mode) during playback, set “Dolby
Digital” in “Audio” setup to “D-PCM”
(page 84).
Playback
The recorder does not play any type of disc
(except HDD).
The recorder does not start playback from the
beginning.
, Resume play was activated (page 53).
, You have inserted a DVD whose Title menu or
DVD menu automatically appears on the TV
screen when it is first inserted. Use the menu to
start playback.
, Multilingual tracks are not recorded on the DVD
being played.
, The DVD VIDEO prohibits the changing of the
language for the sound track.
, Try changing the language using the DVD
VIDEO’s menu.
The subtitle language cannot be changed or
turned off.
, Multilingual subtitles are not recorded on the
DVD VIDEO.
, The DVD VIDEO prohibits changing of the
subtitles.
, Try changing the subtitle using the DVD
VIDEO’s menu.
, The subtitles cannot be changed for the titles
recorded on this recorder.
The angles cannot be changed.
, Multi-angles are not recorded on the DVD
VIDEO being played.
, You are trying to change the angles when “
”
does not appear on the TV screen (page 54).
, The DVD VIDEO prohibits changing angles.
, Try changing the angle using the DVD VIDEO’s
menu.
, The angles cannot be changed for the titles
recorded on this recorder.
Additional Information
, The disc is upside down. Insert the disc with the
labelled side facing up.
, The disc is not correctly inserted.
, Moisture has condensed inside the recorder.
Remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
, If the disc was recorded on another recorder, the
recorder cannot play the disc if it was not
finalized (page 39).
The language for the sound track cannot be
changed.
The MP3 audio tracks do not play.
, The MP3 audio tracks are not recorded in a
format that the recorder can play (page 60).
The recorder starts playing automatically.
The JPEG image files do not play.
, The DVD VIDEO features an auto playback
function.
, The JPEG image files are not recorded in a
format that the recorder can play (page 60).
, Progressive JPEG images cannot be played.
Playback stops automatically.
, If the DVD has an auto pause signal, the recorder
stops playback at the auto pause signal.
TV Pause does not work.
, You are recording to the HDD or the HDD is full.
Some functions such as Stop, Search, or Slowmotion Play cannot be performed.
, Depending on the DVD, you may not be able to
do some of the operations above. See the
instruction manual supplied with the disc.
,continued
91
Recording/Timer recording/
Editing
The programme position cannot be changed
from the programme position you are
recording.
, Set the TV’s input source to “TV.”
Recording does not start immediately after you
press z REC.
, Operate the recorder only after “LOAD,”
“FORMAT,” or “INFOWRITE” disappears
from the front panel display.
Nothing was recorded even though you set the
timer setting correctly.
, There was a power failure during recording.
, The recorder’s internal clock stopped due to a
power failure that lasted for more than 1 hour.
Reset the clock (page 79).
, The channel was disabled after the timer
recording was set. See “Channel Setting” on
page 76.
, Disconnect the mains lead from the mains, and
connect it again.
, “PDC/VPS Scan Off” was selected in the
TOOLS menu (page 43).
, The programme contains copy protection signals
that restrict copying.
, Other timer setting overlapped the timer setting
(page 48).
, There is no DVD inside the recorder.
, There is not enough disc space for the recording.
Recording does not stop immediately after you
press x REC STOP.
, It will take a few seconds for the recorder to input
disc data before recording can stop.
Recording does not stop after you press x.
, Open the remote’s cover and press x REC
STOP.
92
Timer recording is not complete or did not start
from the beginning.
, There was a power failure during recording. If
the power recovers when there is a timer
recording, the recorder resumes recording.
Should the power failure continue for more than
1 hour, reset the clock (page 79).
, Other timer setting overlapped the timer setting
(page 48).
, Disc space was not enough.
, The PDC/VPS function is working.
Contents previously recorded were erased.
, Data that has been recorded on a DVD with a PC
will be erased from the disc when the disc is
inserted.
, “Auto Title Erase” in the TOOLS menu (appears
when you press TOOLS while the Timer List
menu is turned on) is set to “On” (page 49).
, The title was updated and recorded over
(page 43).
The PDC/VPS function does not operate.
, Check that the clock and date are set correctly.
, Check that the PDC/VPS time you set is the
correct one (there might be a mistake in the TV
programme guide). If the broadcast you wanted
to record did not send the good PDC/VPS
information, the recorder will not start recording.
, If the reception is poor, the PDC/VPS signal
might be altered and the recorder might not start
recording.
, “PDC/VPS Scan Off” is selected (page 43).
Recording from the equipment
with a timer
Nothing was recorded even though you set the
Synchro-Rec setting correctly.
, You forgot to turn off the connected equipment.
Turn off the connected equipment and set the
recorder to Synchro-Rec standby mode
(page 49).
, The recorder was not set to the SynchroRecording standby mode. Press SYNCHRO
REC to have the recorder stand by for recording.
Make sure the SYNCHRO REC indicator lights
up on the front panel (page 49).
, The recorder is connected to the TV output jack
of the connected equipment.
Synchro-Recording does not complete.
The recorder automatically starts recording
when the satellite receiver is turned on.
, The Synchro-Rec function was activated. Turn
off the satellite receiver and cancel the SynchroRec function (page 49).
Display
, “Dimmer” in “Options” setup is set to “Power
Save” (page 87).
, The “Power Save” in “Options” setup was set to
“On,” and the recorder is in standby (page 87).
Remote control
The remote does not function.
, Batteries are weak.
, The remote is too far from the recorder.
, The remote’s manufacturer code returned to the
default setting when you replaced the batteries.
Reset the code (page 19).
, Turn on the recorder.
, The remote is not pointed at the remote sensor on
the recorder.
, Different command modes are set for the
recorder and remote. Set the same command
mode (page 21). The default command mode
setting for this recorder and the supplied remote
is DVD3.
, Set the TV/DVD switch to DVD (page 20).
Other Sony equipment responds to the remote.
, The same command mode is set for both the
equipment and recorder. Set a different
command mode for the recorder (page 21).
Additional Information
, The timer setting for the connected equipment
overlapped the recorder’s timer setting
(page 50).
, There was a power failure during the recording.
The clock does not appear in the front panel
display.
Others
The clock has stopped.
, Set the clock again (page 79).
, The clock stopped due to a power failure that
lasted for more than 1 hour. Reset the clock
(page 79).
The TIMER REC indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc inside the recorder.
The recorder does not operate properly.
, Restart the recorder. Press down [/1 on the
recorder for more than ten seconds until
“WELCOME” appears in the front panel display.
, When static electricity, etc., causes the recorder
to operate abnormally, turn off the recorder and
wait until the clock appears in the front panel
display. Then, unplug the recorder and after
leaving it off for a while, plug it in again.
The recording mode indication is incorrect.
, When the recording or dubbing is less than three
minutes, the recording mode indication may be
displayed incorrectly. The actual recording itself
is correctly made in the selected recording mode.
, After playing titles recorded in SLP and SEP
mode, the recording mode indication may
change depending on the recorded programme.
Five numbers or letters are displayed in the
front panel display.
, The self-diagnosis function was activated (see
the table on page 95).
,continued
93
The disc tray does not open after you press Z
(open/close).
, It may take a few seconds for the disc tray to
open after you have recorded or edited a DVD.
This is because the recorder is adding disc data to
the disc.
The disc tray does not open and “TRAY
LOCKED” appears in the front panel display.
, Contact your Sony dealer or local authorized
Sony service facility.
“RECOVERY” appears in the front panel
display.
, The recorder’s recovery function was activated
when the recorder was turned on because the
power was turned off or failed during recording.
Leave the recorder on until “RECOVERY”
disappears from the front panel display.
“HDD ERROR” appears in the front panel
display.
, The hard disk error occurred. Press down @/1 on
the recorder for ten seconds until “WELCOME”
appears in the front panel display. If this does not
resolve the problem, format the recorder’s HDD
by pressing down the HDD button on the
recorder for more than ten seconds until
“FORMAT” appears in the front panel display.
Note that all the contents recorded on the HDD
will be erased. If this does not fix the problem,
contact your nearest Sony dealer.
“FAN ERROR” appears in the front panel
display.
, Check that the vent on the rear of the recorder is
not blocked. Then, immediately disconnect the
mains lead. Leave the recorder off for a while,
then re-connect the mains lead, and press [/1 on
the recorder.
Mechanical sound is heard when the recorder
is off.
, While the recorder is adjusting the clock for the
Auto Clock Set function or scanning the
channels for the PDC/VPS function, operational
noises (such as the internal fan) may be heard,
even when the power is off. This is not a
malfunction.
94
The disc tray does not open and you cannot
remove the disc after you press Z (open/
close).
, Turn off the recorder. Once the clock appears in
the front panel display, disconnect the mains
lead. Connect it again while pressing down A on
the recorder, and release the button when the disc
tray opens. Then, keep [/1 on the recorder
pressed for about ten seconds until
“WELCOME” appears in the front panel display.
“LOCKED” appears in the front panel display.
, The disc tray is locked. Cancel the Child Lock
(page 53).
Self-diagnosis Function
(When letters/numbers
appear in the display)
When the self-diagnosis function is activated to
prevent the recorder from malfunctioning, a fivecharacter service number (e.g., C 13 00) with a
combination of a letter and four numbers appears
in the front panel display. In this case, check the
following table.
First three
characters of
the service
number
Cause and/or corrective
action
C 13
There is a problem in the HDD.
, Contact your nearest Sony
dealer or local authorized
service facility.
The DVD is dirty.
, Clean the disc with a soft
cloth.
Notes About This Recorder
On operation
• If the recorder is brought directly from a cold to
a warm location, or is placed in a very damp
room, moisture may condense on the lenses
inside the recorder. Should this occur, the
recorder may not operate properly. In this case,
remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
• When you move the recorder, take out any discs.
If you don’t, the disc may be damaged.
On adjusting volume
The DVD/CD is not inserted
correctly.
, Re-insert the disc correctly.
E XX
(xx is a number)
To prevent a malfunction, the
recorder has performed the selfdiagnosis function.
, Contact your nearest Sony
dealer or local authorized
Sony service facility and
give the five-character
service number.
Example: E 61 10
On cleaning
Clean the cabinet, panel, and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
About repairing the hard disk drive
• It may be necessary to access data stored on the
hard disk for testing purposes; there is no
intention to copy or store the data, titles or any
other information.
• If replacement or initialization (format) is
required, the hard disk will be formatted at our
discretion. In this case, please note that all of the
contents recorded there will be erased (including
any data found to violate copyright law).
Additional Information
C 31
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level section is played.
On cleaning discs
Do not use a commercially available cleaning
disc. It may cause a malfunction.
Notes about the discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface. Dust,
fingerprints, or scratches on the disc may cause
it to malfunction.
,continued
95
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, or leave it in a car
parked in direct sunlight as the temperature may
rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth. Wipe the
disc from the centre out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
• Do not use the following discs.
– A disc that has a non-standard shape (e.g.,
card, heart).
– A disc with a label or sticker on it.
– A disc that has cellophane tape or sticker
adhesive on it.
Specifications
System
Laser: Semiconductor laser
Channel coverage:
PAL/SECAM (B/G, D/K, I, L)
VHF: E2 to E12, R1 to R12, F2 to F10, Italian
A to H, Ireland A to J, South Africa 4 to 13/
UHF: E21 to E69, R21 to R69, B21 to B69,
F21 to F69/CATV: S01 to S05, S1 to S20,
France B to Q/HYPER: S21 to S41
The above channel coverage merely ensures the
channel reception within these ranges. It does not
guarantee the ability to receive signals in all
circumstances.
Video reception: Frequency synthesizer system
Audio reception: Split carrier system
Aerial out: 75-ohm asymmetrical aerial socket
Timer: Clock: Quartz locked/Timer indication:
24-hour cycle (digital)/Power back-up
duration: 1 hour
Video recording format: MPEG Video
Audio recording format/applicable bit
rate: Dolby Digital 2 ch/256 kbps
Inputs and outputs
LINE 2 OUT
(AUDIO): Phono jack/2 Vrms/10 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE 2 IN/LINE 4 IN
(AUDIO): Phono jack/2 Vrms/more than
22 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE 1 – TV: 21-pin
CVBS IN/OUT
S-Video/RGB OUT (upstream)
LINE 3/DECODER: 21-pin
CVBS IN/OUT
S-Video/RGB IN
S-Video OUT (downstream)
Decoder
DIGITAL OUT (OPTICAL): Optical output jack/
–18 dBm (wave length: 660 nm)
96
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, PB/CB, PR/CR):
Phono jack/Y: 1.0 Vp-p, PB/CB: 0.7 Vp-p,
PR/CR: 0.7 Vp-p
General
Specifications and design are subject to change
without notice.
Compatible colour systems
This recorder is designed to record using the PAL
colour system and play back using the PAL or
NTSC colour systems.
The signals of the SECAM colour system can be
received or recorded but played back in the PAL
colour system only. Recording of video sources
based on other colour systems cannot be
guaranteed.
Additional Information
Power requirements: 220-240 V AC,
50/60 Hz
Power consumption: 52 W
Dimensions (approx.): 430 × 65 × 328 mm
(width/height/depth) incl. projecting parts
Hard disk drive capacity: 80 GB
Mass (approx.): 4.8 kg
Operating temperature: 5ºC to 35ºC
Operating humidity: 25% to 80%
Supplied accessories:
Audio/video cord (1)
Mains lead (1)
Aerial cable (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
97
Guide to Parts and Controls
For more information, see the pages in parentheses.
Remote
A TV/DVD switch (19)
B Z (open/close) button (29)
C [/1 (on/standby) button (22)
1
2
3
4
5
6
7
8
9
0
D HDD button (31)
DVD button (29)
E PROG (programme) +/– buttons (31)
The + button has a tactile dot*.
F Number buttons (45, 59)
SET button (45)
The number 5 button has a tactile dot*.
G
2 (volume) +/– buttons (19)
H CLEAR/-/-- (ten digit) button (45)
I
(audio) button (54)
(subtitle) button (54)
J INPUT SELECT button (50)
t TV/VIDEO button (19)
K DISPLAY button (34)
TIME/TEXT button (34)
L [TIMER] button (43, 45)
M SUR (surround) button (54)
N SYSTEM MENU button (76)
TITLE LIST button (32, 52, 60, 65)
TIMER LIST button (47)
O TOP MENU button (52)
P MENU button (52)
Q </M/m/,/ENTER button (22)
R O RETURN button (47)
S TOOLS button (29)
T
(instant replay)/
buttons (32, 60)
(instant advance)
U ./> (previous/next) buttons (54)
V mc
(54)
/
CM (search) buttons
W VISUAL SEARCH button (59)
98
X H (play) button (52)
X (pause) button (54)
x (stop) button (52)
The H button has a tactile dot*.
Y z REC button (31)
X REC PAUSE button (31)
x REC STOP button (31)
Z REC MODE button (31)
wj CHAPTER MARK/CHAPTER MARK
ERASE buttons (68)
wk SYNCHRO REC buttons (49)
wl
(wide mode) button (19)
e;
(angle) button (54)
ea COMMAND MODE switch (DVD 1,2,3)
(21)
es PROGRESSIVE button (16)
Additional Information
* Use the tactile dot as a reference when operating the
recorder.
,continued
99
Front panel
A [/1 (on/standby) button (22)
B Front panel display (35, 101)
C Disc tray (29)
D TIMER REC indicator (43)
SYNCHRO REC indicator (49)
E A (open/close) button (29)
F HDD button/indicator (31)
DVD button/indicator (29)
G
(remote sensor) (19)
H H (play) button (52)
X (pause) button (54)
x (stop) button (52)
100
I z REC button (31)
X REC PAUSE button (31)
x REC STOP button (31)
J ./> (previous/next) buttons (54)
K PROGRAM +/– buttons (31)
The + button has a tactile dot*.
L INPUT SELECT button (50)
M REC MODE button (41)
N LINE 2 IN (S VIDEO/VIDEO/AUDIO L/
R) jacks (24)
* Use the tactile dot as a reference when operating the
recorder.
Front panel display
HDD
DVD RW
VR
DVD
VCD
NICAM
TV
PROGRESSIVE
SMARTLINK
A HDD/DVD indicators
Displays the selected media and the
playing/recording/dubbing status.
F Displays the following (35):
•
•
•
•
•
•
B Disc type*/recording format
C NICAM indicator (42)
D Audio signal indicators (34)
E TV indicator (31)
Playing time/remaining time
Current title/chapter/track/index number
Recording time/recording mode
Clock
Programme position
TV Direct Rec indication (31): “TV”
appears in the right most two digits.
G
(angle) indicator (54)
I PROGRESSIVE indicator (16)
* Displays DATA CDs as “CD.”
z Hint
You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Power Save” in
“Options” setup (page 87).
Additional Information
H SMARTLINK indicator (14)
Rear panel
LINE 1 - TV
LINE 3
Y
COAXIAL
IN
/DECODER
OUT
R-AUDIO-L
VIDEO
S VIDEO
R-AUDIO-L
VIDEO
S VIDEO
DIGITAL OUT
AERIAL
PCM/DTS/MPEG/
DOLBY DIGITAL
PB / CB
PR / CR
OPTICAL
LINE 4 IN
A AERIAL IN/OUT jacks (13)
LINE 2 OUT
~ AC IN
COMPONENT
VIDEO OUT
B LINE 1 – TV jack (14)
G LINE 2 OUT (R-AUDIO-L/VIDEO) jacks
(14, 17)
C LINE 3/DECODER jack (23)
H LINE 4 IN (S VIDEO) jack (24)
D COMPONENT VIDEO OUT (Y, PB/CB,
PR/CR) jacks (14)
I LINE 4 IN (R-AUDIO-L/VIDEO) jacks
(24)
E AC IN terminal (18)
J DIGITAL OUT (COAXIAL/OPTICAL)
jacks (17)
F LINE 2 OUT (S VIDEO) jack (14)
101
Glossary
Chapter (page 59)
Sections of a picture or a music feature that are
smaller than titles. A title is composed of several
chapters. Depending on the disc, no chapters may
be recorded.
Copy protection signals (page 42)
Copy restriction set by copyright owners, etc.
These signals are included in some software or TV
programmes and restrict recording on this
recorder.
Dolby Digital (page 84)
Digital audio compression technology developed
by Dolby Laboratories. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theater surround sound
systems.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DTS (page 84)
Digital audio compression technology by Digital
Theater Systems, Inc. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DVD+R (page 8)
A DVD+R (read “plus R”) is a recordable disc that
is the same size as a DVD VIDEO. Contents can
be recorded only once to a DVD+R, and will have
the same format as a DVD VIDEO.
102
DVD+RW (page 8)
A DVD+RW (read “plus RW”) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
DVD-R (page 8)
A DVD-R is a recordable disc that is the same size
as a DVD VIDEO. Contents can be recorded only
once to a DVD-R, and will have the same format
as a DVD VIDEO.
DVD-RW (page 8)
A DVD-RW is a recordable and rewritable disc
that is the same size as a DVD VIDEO. The DVDRW has two different modes: VR mode and Video
mode. DVDs created in Video mode have the
same format as a DVD VIDEO, while discs
created in VR (Video Recording) mode allow the
contents to be programmed or edited.
DVD VIDEO (page 10)
A disc that contains up to eight hours of moving
pictures on a disc the same diameter as a CD.
The data capacity of a single-layer and singlesided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a doublelayer and single-sided DVD is 8.5 GB, a singlelayer and double-sided DVD is 9.4 GB, and
double-layer and double-sided DVD is 17 GB.
The picture data uses the MPEG 2 format, which
is a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The DVD
also uses a variable rate coding technology that
changes the data to be allocated according to the
status of the picture. Audio information is
recorded in a multi-channel format, such as Dolby
Digital, allowing you to enjoy a more real audio
presence.
Furthermore, various advanced functions such as
the multi-angle, multilingual, and Parental
Control functions are provided on the DVD.
Hard disk drive (page 2)
A hard disk drive is a whole mechanical system
that consists of disks and drive. Disks are flat,
circular, rigid plates coated with a thin magnetic
media. Magnetic heads record data on the rapidly
spinning disks, and this enables the speedy and
efficient reading and writing of data.
Interlace format (page 16)
Interlace format shows every other line of an
image as a single “field” and is the standard
method for displaying images on television. The
even number field shows the even numbered lines
of an image, and the odd numbered field shows the
odd numbered lines of an image.
MPEG Audio (page 84)
International standard coding system used to
compress audio digital signals authorized by ISO/
IEC. MPEG 2, used on DVDs, conforms to up to
7.1-channel surround.
Original (page 64)
Titles actually recorded on a HDD/DVD-RW (VR
mode). Erasing original titles frees up disc space.
Playlist (page 64)
Progressive format (page 16)
Compared to the Interlace format that alternately
shows every other line of an image (field) to create
one frame, the Progressive format shows the entire
image at once as a single frame. This means that
while the Interlace format can show 25-30 frames/
50-60 fields in one second, the Progressive format
can show 50/60 frames in one second. The overall
picture quality increases and still images, text, and
horizontal lines appear sharper.
Additional Information
Playback information created from the actual
recordings on a HDD/DVD-RW (VR mode). A
Playlist leaves the original titles as they are, and
contains only the information needed to control
playback. A Playlist title takes up very little disc
space.
Title (page 59)
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
Track (page 59)
Sections of a music feature on a CD/VIDEO CD
(the length of a song).
103
Language Code List
For details, see page 80.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volap k
Wolof
Xhosa
Yoruba
Chinese
Zulu
1703 Not specified
Area Code
For details, see page 85.
104
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Spain
Sweden
Switzerland
Thailand
United
Kingdom
Index
Words in quotations appear in
the on-screen displays.
Numerics
16:9 22, 81
4:3 Letter Box 22, 81
4:3 Pan Scan 22, 81
“48kHz/96kHz PCM” 84
A
“A-B Erase” 66
Adjusting
playback picture 56
playback sound 56
recording picture 46
Aerial 13
“AFT” 77
Album 35, 63
Album number 35
“Album Search” 59
Angle 54
Area code 104
“Audio” 80
Audio 54, 83
“Audio Connection” 22
Audio cord 17
“Audio DRC” 83
“Audio Filter” 57
“Audio Settings” 56
“Auto Adjust” 79
“Auto Chapter” 85
Auto Clock Set 79
“Auto Display” 88
“Auto Title Erase” 49
“AV SYNC” 57
B
Batteries 19
“Bilingual” 50, 51
Bilingual recording 42
“BNR” 56
“Brightness” 47, 56
C
D
“C NR” 56
Canal Plus 26
“Capture” 69
“Capture All” 69
“CATV” 76
CD 10
“Change IN” 69
“Change OUT” 69
“Channel List” 78
“Channel Setting” 76
Chapter 35, 47, 68, 102
CHAPTER MARK 68
CHAPTER MARK ERASE
68
Chapter number 35
“Chapter Search” 59
Chasing Playback 57
“Check Overlap” 48
Child Lock 53
Cleaning discs 95
Clock 22, 79
“Colour” 47, 56
“Colour System” 86
Colour Systems 97
“Combine” 70
“Command Mode” 21, 88
“Component Out” 81
Component video input 14
COMPONENT VIDEO OUT
14
Connecting 14
the aerial cable 13
the audio cords 17
the video cords 14
“Contrast” 47, 56
Controlling TVs with the
remote 19
Copy control signals 42
Copy protection 102
Copy-Free 42
Copy-Never 42
Copy-Once 42
CPRM 8
“Create Playlist” 69
Creating chapters 68
DATA CD 10
“Decoder” 27
“Digital Out” 84
“Dimmer” 87
“Disc Info” 29, 38, 68
Disc Map 68
Disc Settings 29, 38, 68, 87
Disc space 30
Disc types 8
Display
front panel display 35,
101
“Divide” 67
Dolby Digital 17, 84, 102
“Downmix” 83
DTS 84, 102
“Dub Mode” 71
Dubbing 71
“Dub Mode” 71
High-speed Dubbing 71
Rec Mode Conversion
Dubbing 72
“Settings” 75
“DVD Bilingual Rec.” 87
“DVD Menu” 80
“DVD Rec. Picture Size” 46
DVD VIDEO 10, 102
DVD+R 8, 102
DVD+RW 8, 102
DVD-R 8, 102
DVD-RW 8, 102
DVD-RWs (Video mode) 65
“DVE” 56
E
Easy Setup 22, 88
Editing 64, 69
Enter characters 36
“Erase” 48, 65, 69
“Erase All” 68
“Erase Titles” 67
“Extend Rec” 44
105
F
M
“Factory Setup” 88
“Features” 85
“File Search” 59
“Finalize” 39
Finalizing 39
“Format” 29
“Format DVD” 87
Formatting 29
Freeze Frame 55
Front panel 100
Front panel display 35, 101
Mains Lead 18
Manual Clock Set 80
MENU 52
Menu
DVD’s Menu 52
Top menu 52
“MNR” 56
“Modify” 48
“Move” 69
MP3 audio tracks 60
MPEG 84, 103
G
N
GB 30
NICAM 42, 77
“Normal” 76
Number buttons 37, 45
H
Handling discs 95
“HDD Bilingual Rec.” 87
Hue 56
I
INPUT SELECT 51
Interlace 103
Interlace format 103
J
JPEG image files 60
L
Labelling 38
Language 80
LINE 2 IN 24
LINE 3/DECODER 23
LINE 4 IN 24
“Line Audio Input” 50, 51
“Line1 Output” 82
“Line3 Input” 82
“Line3 Output” 82
“Line4 Input” 82
106
O
One Touch Menu 53
One Touch Play 53
One Touch Timer 44
On-screen display
“OSD” language 22, 80
“Options” 87
Original 33, 64, 103
P
Page mode 33
Parental Control 53, 85
Parts and controls 98
“Pause Mode” 81
PAY-TV 26
“PAY-TV/CANAL +” 78
“PB Video Equalizer” 56
PBC 52
PDC 43
Picture quality 46, 56
Picture size 46
“Play Beginning” 53
Play mode 35
Playable discs 10
Playback 10, 35, 52, 54, 55
fast forward 55
fast reverse 55
freeze frame 55
instant advance 54
instant replay 54
JPEG image files 60
MP3 audio tracks 60
resume play 53
scan audio 52
slow-motion play 55
Playing status bar 35
Playlist 33, 64, 69, 103
“Power Save” 87
“Present Time” 80
“Preview” 69
Progressive 16, 103
“Progressive Mode” 82
“Protect” 65
“Protect Disc” 38
Protection
disc 38
title 65
Q
Quick guide to disc types 8
Quick Timer 46
R
Rear panel 101
“Rec Mode” 46
Rec Mode Adjust 44
“Rec NR” 46
REC PAUSE 31
“Rec Settings” 46
“Rec Video Equalizer” 47
Recordable discs 8
Recording 41, 49, 85
picture adjustment 46
recording format 8
recording mode 32, 41
recording time 32
“Update” 43
while watching another
programme 31
Recording time 41
RECOVERY 94
Region code 11
Remaining time 35
Remote 19, 98
Resetting the recorder 88
Resume Play 53
“RGB” 82, 22
,continued
S
T
S VIDEO 14
“S Video” 22, 82
Scan Audio 52
“Scart Setting” 82
Scene List 69
Screen Saver 86
“Search” 59
Searching
fast reverse/fast forward
54
locating the beginning of
the title/chapter/
track 54
scan audio 52
search mode 59
visual search 59
SET 20, 37
“Set Thumbnail” 65
“Settings” 76
Simultaneous Rec and Play 58
Slow-motion play 55
SMARTLINK 15
Sort 33
Sound quality 56
“Station Name” 78
Subtitle 54, 80
Super VIDEO CD 10
Surround 54
Synchro Rec 49
“System” 76
Teletext 32, 79
Thumbnail picture 34
“Time Search” 59
TIME/TEXT 35
TIMER 43
Timer List 47
Timer recording
check/change/cancel 47
manual setting 43
Rec Mode Adjust 44
Synchro Rec 49
Video Plus+ 45
Title 35, 103
TITLE LIST 52
Title List 32, 52
Sort 33
Thumbnail 34
“Title Name” 65
Title number 35
“Title Search” 59
TOP MENU 52
Track 103
“Track Search” 59
Troubleshooting 89
Tuner System 22
“TV Direct Rec” 31, 85
“TV Guide Page” 79
TV Pause 57
TV system 76
“TV Type” 22, 81
TV/DVD switch 19
TV/VIDEO 31
TVS (TV Virtual Surround)
54
Visual Search 59
VPS 43
VR mode 8, 64
Y
“Y NR” 56
Z
ZWEITON 42
U
“Unfinalize” 40
Unfinalizing 40
Usable discs 8, 10
V
VIDEO CD 10
Video cord 14
“Video” 22, 82, 81
Video input 14
Video mode 8
Video Plus+ 45
“Video Settings” 56
107
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in Malaysia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement