User manual | DMP XR20 - metrodial

XR20
User’s Guide
Silencing an Alarm
All/Perimeter and Home/Away Systems
While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM
SILENCE.
Press the Select key under SILENCE to stop the bell or siren. This does NOT disarm the system.
Area Systems
While the alarm bell or siren is sounding, enter your user code. The system silences the alarm bell or
siren.
What to do when a trouble tone is sounding
You can silence the trouble tone by pressing any one of the top row Select keys. This only
silences the keypad and does not correct the condition that originally caused the problem.
Copyright© 1999 - 2003 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Security Command User’s Guide
for XR20 Command Processor™ Panels
Table of Contents
Section
Page
Emergency Evacuation Plans .............................. iv
Draw a ßoorplan of your home or business ................. iv
Develop escape routes............................................... iv
Decide where to meet ............................................... iv
Practice your escape plans ......................................... iv
Early detection .......................................................... iv
Introduction ......................................................... 1
About Your Security System ........................................ 1
The Security Command Keypad ................................... 2
32-Character User Options .......................................... 3
Special Security Command Tones ................................ 3
Special Security Command Displays ............................. 4
Arming and Disarming ......................................... 7
How your System Operates ......................................... 7
Arming Functions ....................................................... 7
Area System Arming ................................................... 8
Area System Disarming............................................... 9
All/Perimeter System Arming..................................... 10
All/Perimeter System Disarming................................. 11
Home/Away System Arming ...................................... 12
Home/Away System Disarming.................................. 13
Section
Page
User Menu .......................................................... 14
Accessing the User Menu .......................................... 14
User Menu Options................................................... 14
User Check-in........................................................... 15
Zone Activity Check .................................................. 15
Sensor Reset............................................................ 16
Outputs On Off ....................................................... 16
Bypass Zones........................................................... 17
Zone Monitor ........................................................... 17
Using the Zone Monitor Function ............................... 18
System Test ............................................................. 18
User Codes .............................................................. 19
Ambush Codes ......................................................... 21
Schedules ................................................................ 22
Extended Schedules ................................................. 23
Date and Time ......................................................... 23
Display Events ......................................................... 24
Service Request?...................................................... 24
XR20 User’s Guide
i
System Setup ..................................................... 25
System Setup Record................................................ 25
Area Names and Numbers Record ............................. 25
Output relays ........................................................... 25
User Codes .............................................................. 26
Appendix A ......................................................... 28
About the Display Events Section .............................. 28
Zone Activity Check Event Display ............................. 28
Zone Bypass Event Displays ...................................... 28
Zone Event Displays ................................................. 29
Arming and Disarming Event Displays ........................ 29
User Check-in Event Displays .................................... 30
User Code Change Event Displays ............................. 30
Supervisory Event Displays ....................................... 30
System Monitor Event Displays.................................. 30
ii
Appendix B ......................................................... 31
Easy Entry™ User’s Guide ......................................... 31
Pager Direct™ User’s Guide....................................... 33
PhoneAccess™ User’s Guide...................................... 35
Quick Reference Wallet Card ..................................... 35
895 Voice Module .................................................... 36
FA113 User’s Guide .................................................. 37
Common Keypad Displays ......................................... 38
Index .................................................................. 40
XR20 User’s Guide
This page intentionally left blank.
XR20 User’s Guide
iii
Emergency Evacuation Plans
First Floor
The National Fire Protection Association recommends that you
establish an emergency evacuation plan to safeguard lives in the
event of a Þre or other emergency.
Second Floor
Fire Escape
Draw a ßoorplan of your home or business
On a sheet of paper, draw the walls, windows, doors, and stairs.
Also draw any obstacles, such as large furniture or appliances, a
person may encounter while exiting the building.
Window Ladder
Building Front
Develop escape routes
Building Back
Determine at least two routes the occupants in each room can take
to safely escape. One route can be the most obvious such as the
door. Another can be through a window that can be easily opened.
If the window is high off the ground, an escape ladder should be
provided. Draw arrows on the ßoorplan to show escape routes from
each room.
Decide where to meet
Prearrange a meeting place outside and away from where
emergency personnel are likely to be working. A neighbor’s house
or across the street in the front of the house are good locations.
Always perform a head count to make sure all occupants safely
exited. NEVER ENTER A BURNING BUILDING. If the head count shows
one or more persons missing, give this information immediately to
the authorities. Never enter a building to look for someone.
Early detection
The best way to survive a Þre or other emergency is to get out
early. The installation of a Þre alarm system, with smoke and
carbon monoxide detectors in each room, can greatly decrease
your risk of loss or injury.
Practice your escape plans
Devising an escape plan is only the beginning, before the plan can
be effective everyone should practice the escape routes from each
room.
iv
XR20 User’s Guide
About Your Security System
Introduction
The Security Command system has been designed with your
safety and comfort in mind. It uses the latest in computer based
technology to create the most advanced, user friendly security,
Þre, and access control system available.
The Security Command system combines ease of use with a simple
to understand Security Command keypad to offer the full range of
features requested by today’s security system owners.
Use the Security Command system to turn portions of your
protection on or off by pressing a few keys, or have the system turn
on or off automatically by entering a simple schedule. You can add,
delete, and change personal user codes at any time or check the
status of protection devices in the system.
Parts of the System
There are two main parts to the Security Command system, the
Security Command keypad and the keypad User Menu.
Security Command Keypad
This is the device we have placed at certain locations throughout
the premises that allow you to turn the system’s protection on and
off using your personal user code.
Keypad User Menu
The keypad provides a simple User Menu containing all of the
functions you need to fully operate your system such as changing
the time of day or a personal user code.
Introduction
A Note About False Alarms
One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and
Þre agencies places others in jeopardy by limiting the response
capability of those emergency service units. We take this concern
seriously and have spent many hours training our employees to
recognize the causes of false alarms and prevent them from
occurring.
As part of our commitment to reducing false alarms, we would like
to encourage you to read this guide thoroughly. All the information
contained here can help you quickly, and comfortably, learn the
operation of the Security Command system. If you have any
additional questions, or feel that you need more training, please
do not hesitate to contact us.
Test Your System Weekly
It is recommended that you test the burglary portion of your system
at least once each week. Testing should involve an active test of all
doors, windows, and motion detectors connected to your system.
If your system also has Þre protection, call the service department
to Þnd out how this portion of your system should be tested.
Refer to the System Test section of this guide for instructions on
testing the burglary portion of your system and refer to the Fire
Drill section for instructions on testing your system Þre bells.
XR20 User’s Guide
1
The Security Command Keypad
Your system may have one or more easy to use Security Command
keypads that allow you to properly operate the system.
COMMAND key
The COMMAND key allows you to advance through the keypad
displays or User Menu or complete a data entry function.
The Select keys
There are four keys under the display called the Select keys. These
keys are one of the features that make your system so easy to
operate by allowing you to make selections by pressing the Select
key under choice being shown in the display.
Back Arrow key
The Back Arrow key is used to go back through the keypad displays
while operating your system. You can press the Back Arrow key to
back up through the list of functions in the User Menu or to erase
the last character you entered.
For the purposes of this guide, when instructed to press the Þrst
Select key, press the far left Select key; the second Select key is
the second from the left; third Select key is second from the right;
and the fourth Select key is the far right key.
POWER LED
This LED remains on steady as long as your system is connected to
its AC power supply. Should there be an interruption, the LED turns
off and the system’s backup battery maintains normal operation for
a time so you can contact the service department.
32-Character LCD Display
Power LED
Armed LED
ABC PRINTING
F R I 2 : 51 AM
R
A
R
M
E
ARMED LED
This LED is ON steady anytime a burglary protection area is armed
and is OFF when ALL areas are disarmed.
D
2-Button Panic Keys
Your keypad may be set up to send a Panic, Emergency, or Fire
report to the central station. This function is optional. An
icon label should appear above the Select keys if this option is
programmed for your keypad.
Select Keys
1
ABC
Speaker
5
MNO
9
YZ
2
D EF
6
P Q R
0
3
GH I
7
STU
4
JKL
8
V WX
COMMAND
COMMAND Key
Back Arrow Key
To send a panic, press and hold the two Select keys for 2 seconds,
until a beep from the keypad is heard.
Digit keys for Data Entry
Top Row Select Keys
Data Entry keys
These keys allow you to enter your user code when arming or
disarming or enter other information into the system.
2
XR20 User’s Guide
Police
Emergency
Fire
Label shows
icons only
Introduction
32-Character User Options
Special Security Command Tones
To access the User Options portion of the keypad, press and hold
the Back Arrow and COMMAND keys for two seconds. The keypad
display changes to SET BRIGHTNESS. Press the COMMAND key to
display the next option or the Back Arrow key to exit.
Your keypad also contains a small speaker that allows it to alert
you to events as they occur on your system. Below are brief
descriptions of the different tones you will hear from the keypad:
Backlighting Brightness
Set the brightness level of the keypad’s LCD, AC LED, and the Green
keyboard backlighting. At the SET BRIGHTNESS display, use the left
Select key to lower the keypad brightness. Use the right Select key
to increase the brightness.
Note: If the brightness level is lowered, it temporarily reverts back
to maximum intensity whenever a key is pressed.
Internal Speaker Tone
Set the tone of the keypad’s internal speaker. At the SET TONE
display, use the top left Select key to make the tone lower. Use the
right Select key to make the tone higher.
Volume level
Set the volume level of the keypad’s internal speaker for key
presses and prewarn conditions. During alarm, trouble, and
prewarn conditions, the volume is always at maximum level. At
SET VOLUME LEVEL, use the left Select key to lower the keypad
volume. Use the right Select key to raise the volume.
Model Number
The keypad’s model number and Þrmware version and date are
displayed, but cannot be changed.
Keypad Address
The keypad’s current address is displayed, but cannot be changed.
Press the Back Arrow key to exit the User Options function.
Introduction
Fire alert: Your keypad may sound a Þre tone to alert persons in
the vicinity to the alarm condition. This is in addition to the bell
output from the alarm panel.
Burglary alert: Your keypad may sound a burglary tone to alert
persons in the vicinity to the alarm condition. This is in addition to
the bell output from the alarm panel.
Key press tone: A short beep as you press a key on the keypad.
Prewarn tone: A continuous pulsed tone that sounds when you
open an entry delay door on a system that is armed (turned on)
reminding you to disarm the burglary protection.
Monitor tone: A short tone that sounds for one second whenever
a door or window is opened while you are using the zone monitor
function from the User Menu. See Zone Monitor.
Trouble tone: A steady tone indicating a trouble condition on your
system. Press a Select key to silence the trouble tone.
Zone Activity Check tone: A steady tone indicating no zone activity
has occurred on your system within the programmed period of
time. Press any key to silence the tone.
What to do when the trouble tone is sounding
You can silence the trouble tone by pressing any one of the top row
Select keys. This only silences the keypad and does not correct the
condition that originally caused the problem.
XR20 User’s Guide
3
Special Security Command Displays
As you use your system, you will occasionally see a keypad display
that asks you to enter a user code or describes a condition on the
system. Below are some examples of the displays you will see.
ALARM
A 24-hour zone, such as a Þre or panic zone, or an armed burglary
zone has been faulted. Your system may sound bells or sirens.
INVALID CODE
The user code you have entered is considered invalid by the
system.
SYSTEM TROUBLE or SERVICE REQUIRED
There is an electronic failure in your system. Contact the service
department as soon as possible.
ALARM CANCELLED
This message displays when an authorized user has cancelled
an alarm condition by entering a valid user code and an “Alarm
Cancelled” report was sent to the central station.
TROUBLE
There is a problem with a protection device or system component.
This display is accompanied by a description of the problem.
ENTER CODE
The system requires you to enter a personal user code. User
codes can be required for turning your system on (arming), turning
your system off (disarming), and performing many other system
options.
As you enter your user code, the keypad display shows an asterisk
(*) in place of each digit pressed. This prevents others from seeing
your user code on the display as it is entered.
TRY AGAIN
The user code entered is not recognized by the system. Check the
user code and try again.
4
XR20 User’s Guide
Introduction
Understanding Security System Terms
Throughout this guide, and in some displays on your keypad, you
will see certain words or phrases that might be unfamiliar. Although
every effort has been made to use terms that are commonly known,
there are some for which there was no acceptable substitute.
Below are some terms you will see here and on the keypad
display.
Arming
This is the term used for turning on the burglary protection in one
or more areas of the system. Your system may require you to enter
a user code. When armed, the system is able to sound alarm bells
or sirens and, if monitored, send alarm reports to a central station
when a burglary zone is faulted.
Entry or Exit Zone
Almost all systems have one or more doors through which you can
enter or exit the premises. These doors are programmed with a
delay time to allow you to enter or exit while the system is armed
without setting off the alarm.
When you arm the system, activity on all burglary zones is ignored
until the programmed exit delay time expires. Once that time has
expired and the system is fully armed, opening the door causes the
panel to start the entry delay time. During the entry delay time,
you must enter a valid user code to disarm the system or an alarm
will occur.
Fire, panic, and other 24-hour devices are always turned on and do
not need to be armed.
Instant Zone
Exterior windows and non-entry doors, or interior protection
devices, are typically not programmed with delay times. If these
zones are faulted while the system is armed, an alarm occurs
instantly.
Disarming
This means turning off one or more areas of the system. When
disarmed, the system does NOT sound alarms or send alarm reports
to a central station when a burglary zone is faulted.
24-Hour Zone
A 24-hour zone is never assigned to an area and is not turned on or
off by arming or disarming your system. Some examples of 24-hour
zones are Þre zones, panic zones, and temperature control zones.
Zone
A zone refers to a group of one or more protected openings or
protection devices assigned the same zone number. Each door or
window, motion detector, smoke detector, or other device has a
zone number and a name.
Areas
An area is made up of burglary zones that can be armed or
disarmed together. The Perimeter area, for example, consists of
all the doors and windows on the outside of the building. When you
arm the Perimeter, these zones sound an alarm if tripped.
Often, similar devices in the same general area will share the same
zone. For example, the windows on the east side of the premises
can all be grouped together in a zone named E. WINDOWS.
Introduction
XR20 User’s Guide
5
Central Station Monitoring
Your system can also be programmed to automatically send alarm,
trouble, and arming and disarming reports to a central station.
Operators at the central station can then dispatch the appropriate
authorities or contact you with the speciÞc event information.
If an alarm occurs on a non-Þre, 24-hour zone or a system monitor,
it remains in the Status List until it restores. If one or more armed
burglary zones trips, the last one to trip remains in the Status List.
The burglary zone alarm remains in the Status List for several
minutes or until it is cleared by disarming the system.
Status
Status is a feature that automatically displays the armed or
disarmed status of your system on the Security Command keypads.
Alarm or trouble conditions on a zone or a system monitor such as
AC or battery trouble can also be displayed. There are two types of
status information available: Armed Status and Status List.
Zone Status
To display the status of a particular zone, enter the zone number
followed by the COMMAND key when the keypad is displaying the
Status List.
Armed Status
With Armed Status, the keypad displays the current armed condition
of areas within your security system.
The keypad displays
When
PERIMETER ON
The perimeter areas are on
ALL SYSTEM ON
All areas are on
PERIM/INT ON
The perimeter and interior areas are on but the
bedroom area is off
Also, for keypads that include an Armed LED, the Armed LED is ON
steady anytime a burglary protection area is armed and OFF when
ALL areas are disarmed.
Status List
The keypad Status List displays any alarm or trouble condition on
a zone and any trouble condition that occurs with the AC power or
battery power. If your system contains any Panic zones, these are
not displayed on the keypad for security reasons.
6
Exit Error
This is an automatic function of the panel that prevents an alarm
from occurring if an exit door does not close all the way after the
system has been armed. Here is how it works:
You close all doors and windows, arm the system, and then leave by
the front door. You close the door but it does not latch causing the
front door zone to show as an open to the system. After the exit
delay time expires the system attempts to arm the front door zone
but recognizes the open condition. Instead of sending an alarm
report to the central station, the system sends an Exit Error report
and force arms the door. (If the door closes at a later time it will
be included back into the system.) The system sounds the sirens
for 15 seconds to alert you of the condition and allow you to close
the door.
The Exit Error feature allows the central station to acknowledge
the arming error without dispatching the police on a false alarm.
XR20 User’s Guide
Introduction
How your System Operates
Arming and Disarming
Your system has been programmed to operate in one of three
modes: Area Arming, All/Perimeter, or Home/Sleep/Away.
• Area Arming - Your burglary protection is divided into up to four
areas. Each area can have a custom name, be turned on or off
independently of other areas, and limit access to only those users
with the proper authority.
• All/Perimeter - Your burglary protection is divided into two areas:
Interior and Perimeter. You can turn on the just the Perimeter
protection while inside for security or turn on both as you leave.
• Home/Sleep/Away - Your burglary protection is divided into three
areas: Interior, Perimeter, and Bedrooms. You can turn on the
Perimeter, Perimeter and Interior, or all three areas separately.
Regardless of which mode has been programmed, much of the
operation is similar. Throughout this guide, any differences
between the systems are noted for your convenience.
Arming Functions
After making your arming selection, the keypad displays any zones
that are currently bypassed. These zones remain bypassed until
the system is armed and then disarmed. Any 24-hour zones in a bad
condition are also displayed.
During arming, the system veriÞes that all doors, windows, and
other protection devices to be armed are in normal condition.
If everything is normal, the system arms. If there is a problem on
one or more burglary zones the keypad displays the problem and
allows you to bypass those zones.
Arming and Disarming
If the problem can be corrected by closing a door or window, do
not bypass the zone. Instead, correct the problem and try arming
again. If the problem cannot be corrected, you can bypass the zone
or wait until the zone can be repaired by a service technician. A
bypassed zone is ignored by the system during the armed period.
In some cases, you might see the keypad display FRONT DOOR
— FAULT. The keypad may then display priority zone which is a
zone that cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.
Armed Message: After all bypassing is completed or zone faults
corrected, the areas you selected are armed. The keypad brießy
displays ALL SYSTEM ON if all areas in the system are arming and
PERIMETER ON or PERIM/INT ON if only selected areas are arming.
The keypad then displays the exit delay as it counts down. Zones
are not armed until the exit delay time expires.
If your system uses a keyswitch to arm an area, the exit delay time
is NOT shown on the keypad display.
DIALING . . . Message: If your system is monitored, it may be
programmed to wait for the arming report to be sent to the central
station before displaying the armed message. (See Arming Report
below.) This is to verify your phone lines are working properly.
While the system is waiting, the display reads DIALING.... If the
report is received, the keypad buzzes for one second and displays
the armed message. If the report is not received, the keypad
displays LOCAL ALARM ONLY before displaying the armed message.
Arming Report: Your system can be programmed to send arming or
zone bypass reports to a central station. This feature is optional
and can be programmed for you at any time.
XR20 User’s Guide
7
Area System Arming
Area Assignment: Your security system has been programmed into
separate areas. The number of areas and their names are listed in
the back of this guide.
Arming or Disarming: You can arm and disarm all areas at one
time or each area individually. You can only arm or disarm areas
authorized for your user code.
All or Selective Arming: After entering your user code, the system
allows you to arm either all of the areas to which you have access
or one or more selected areas. If you choose to arm all areas, the
system begins verifying that all zones in those areas are in a good
condition. If you choose to arm selected areas, the system prompts
you to choose the areas you want to arm.
Arming the System
1. Press the COMMAND key until ARM DISARM displays.
The system displays any zones that have been bypassed
prior to arming and any bad 24 hour zones. No action is
required.
7.
At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system
if it later returns to normal. A zone that is bypassed will
remain bypassed until the system is disarmed. See steps 7a
through 7d.
7a.
If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
7c. Select BYPASS to bypass the zone(s) before arming.
Select ARM to turn on all protection.
3.
Enter your user code if required. The display reads ALL? NO
YES.
4.
Select NO to arm only selected areas. Go to step 5.
Select YES to arm all areas authorized for your user code.
Go to step 6.
If NO is selected in step 4, the display begins to list each
area to which you have access followed by NO YES.
Example: OFFICE NO YES.
6.
7b. Select OKAY to force arm the zone(s) before arming.
2.
5.
Note: You can also just press the area numbers you want to arm
while at the ALL? NO YES display. This changes the display
to AREAS:. The numbers you select appear in the display.
For example: AREAS: 2 4. Press COMMAND when done.
7d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
8.
The display reads SYSTEM ON if at least one area in the
system is armed, and ALL SYSTEM ON if all areas in the
system are armed.
9.
The keypad then displays the exit time in seconds and
counts down the remaining time: EXIT: # # (# # = seconds
remaining). The exit zones arm when the delay time
expires.
5a. Select YES for each area you want to arm.
5b. Select NO for each area you do NOT want to arm.
8
XR20 User’s Guide
Arming and Disarming
Area System Disarming
Disarming: While the system is armed, you can only enter the
premises through an exit/entry delay door without causing an
alarm. After opening the door, the Security Command keypad
sounds a prewarn tone to remind you to disarm the system. You
must disarm the system before the delay time expires or an alarm
will occur.
During the prewarn tone, the keypad displays ENTER CODE: Enter
your user code to disarm the system. Only those areas authorized
for your user code will disarm.
All or Selective Disarming: After entering your user code, the
system allows you to disarm either all of the areas to which you
have access or just selected areas. If you choose to disarm all
areas, the system automatically disarms them. If you choose to
disarm selected areas, the names of those areas will be displayed
on the keypad.
Disarming an Area System
1. Press the COMMAND key until ARM DISARM is displayed.
During entry delay this process starts at step 3 below.
2.
Select DISARM to disarm areas.
3.
The keypad displays ENTER CODE: . Enter your user code.
The keypad displays ALL? NO YES.
4.
Select YES to disarm all areas authorized for your user
code.
4a. Select NO to disarm only certain areas individually. The
keypad then displays the name of each area authorized for
your code followed by the NO YES display.
4b. Choose YES to disarm the area displayed.
4c. Choose NO to not disarm and to display the next area.
Note: You can also just press the area numbers you want to
disarm while at the ALL? NO YES display. This changes the
display to AREAS: . The area numbers you select appear in
the display. For example: AREAS: 2 4.
Alarm Display: After disarming, the keypad displays any zones that
went into alarm or any communication problems that occurred
during the armed period. All burglary zones are then disarmed and
any bypassed zones are automatically reset.
To remove an area number from the display, press its
corresponding number on the keypad.
Press COMMAND when done.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the
system disarms.
5.
Central Station Report: A report of the disarming can be sent to
the central station. If your system does not have this feature, it
can be programmed for you at any time.
After all areas have been displayed, any alarms or
communication problems that occurred during the armed
period are shown.
6.
If all areas have been disarmed, the keypad displays ALL
SYSTEM OFF.
Arming and Disarming
XR20 User’s Guide
9
All/Perimeter System Arming
Area Assignment: Your security system is divided into two
separate areas. Motion detectors, inside doors, and other interior
protection devices are assigned to the Interior area while windows
and exterior doors are assigned to the Perimeter area.
Perimeter or All: When arming an All/Perimeter system, the
keypad displays PERIM
ALL. If you select ALL, you arm both
the Perimeter and the Interior of the system. You will want to arm
both of these areas when leaving with nobody left inside. Selecting
PERIM arms only the Perimeter of the system. Perimeter arming is
for when you are staying inside but want the comfort of knowing
the exterior doors and windows are armed. Perimeter arming
allows you to move freely about inside without setting off any
interior alarms.
Arming an All/Perimeter System
1. Enter your code. The keypad displays PERIM
ALL.
2.
Select PERIM to arm the Perimeter area only.
3.
Select ALL to arm both the Perimeter and Interior areas.
4.
The keypad displays any bypassed zones and 24-hour zones
that are in a bad condition. No action is required by you.
5.
At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if
it later returns to normal. A bypassed zone remain bypassed
until the system is disarmed. See steps 5a through 5d.
5a.
If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
System Ready/System Not Ready Keypad Displays
When all zones in the system are in a normal condition, the keypad
displays SYSTEM READY. If there are one or more zones that are
not in a normal condition, the keypad displays SYSTEM NOT READY.
Pressing any top row Select key during this display shows the zone
name allowing you to investigate the problem.
5c. Select BYPASS to bypass the zone(s) before arming.
6.
The keypad displays PERIMETER ON if only the perimeter is
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.
Instant Arming
Instant: During the exit delay time, you can cancel the exit and
entry delays and cause all zones to be instant zones. Press the far
right select key under INSTNT while the exit delay is displayed.
This immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.
7.
The keypad next displays EXIT: ## INSTNT and begins to
count down the number of seconds remaining for you to
exit. When the delay expires, all zones are armed.
8.
You can select INSTNT while EXIT: ## INSTNT is displayed
to immediately arm all zones and make them instant. The
keypad displays INSTANT.
9.
When the system is fully armed, the keypad displays
PERIMETER ON for perimeter arming and ALL SYSTEM ON
for perimeter and interior arming.
10
5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
XR20 User’s Guide
Arming and Disarming
All/Perimeter System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the Security Command keypad
sounds a prewarn tone to remind you to disarm the system. You
must disarm the system before the prewarn tone expires or an
alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your user code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones
that tripped or any transmission problems that occurred during
the armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the
system disarms.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user
code. The keypad displays DISARM SILENCE.
2.
Press the Select key under DISARM to disarm the system and
silence the alarm.
The keypad next displays ALL SYSTEM OFF to conÞrm the
system is disarmed.
3.
Press the Select key under SILENCE to stop the bell or siren
but NOT disarm the system.
If you do not press any Select key, or you press the
COMMAND key, the system will automatically disarm and
silence the alarm.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this report
to the central station. Be sure that you want the alarm message
to be cancelled BEFORE deciding to disarm the system. If you do
not want to disarm the system and send the abort report, press
SILENCE to only turn off the alarm bells.
Disarming an All/Perimeter System
1. During the entry delay time, the keypad displays ENTER
CODE:. Enter your user code.
2.
The keypad displays any zones that went into alarm and any
communication problems that occurred during the armed
period.
3.
The keypad next displays ALL SYSTEM OFF to conÞrm the
system is disarmed.
Arming and Disarming
XR20 User’s Guide
11
Home/Away System Arming
6.
At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system
if it later returns to normal. A zone that is bypassed will
remain bypassed until the system is disarmed. See steps 6a
through 6d.
6a.
If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
Area Assignment: Your security system is divided into two or three
separate areas. Motion detectors, inside doors, and other interior
devices are assigned to an Interior and possibly Bedroom area while
windows and exterior doors, are assigned to a Perimeter area.
Arming the system: When arming a Home/Away system, the
keypad displays HOME AWAY or HOME SLEEP AWAY. If you select
AWAY, you arm all areas of the system. You will want to arm all
areas when leaving with nobody staying inside. Selecting HOME
arms only the Perimeter of the system. Perimeter arming is for
when you are staying inside but want the comfort of knowing the
exterior doors and windows are armed. Selecting SLEEP arms the
Perimeter and Interior devices but leaves devices near bedrooms
and other nighttime areas off.
System Ready/System Not Ready Keypad Displays
When all zones in the system are in a normal condition and can be
armed without bypassing, the keypad displays SYSTEM READY. If
there are one or more zones that are not in a normal condition, the
keypad displays SYSTEM NOT READY. Pressing any top row Select
key during this display shows the bad zone name.
Arming a Home/Away System
1. Enter your user code. The keypad displays HOME
HOME SLEEP AWAY (you may have three areas).
12
AWAY or
2.
Select HOME to arm the Perimeter only.
3.
Select SLEEP to arm the Perimeter and Interior.
4.
Select AWAY to arm the Perimeter, Interior, and Bedroom.
5.
The keypad displays zones that have been bypassed prior to
arming and 24-hour zones that are in a bad condition. No
action is required by you.
6b. Select OKAY to force arm the zone(s) before arming.
6c. Select BYPASS to bypass the zone(s) before arming.
6d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
7.
The keypad displays PERIMETER ON if you selected HOME,
or PERIM/INT ON if you selected SLEEP, or ALL SYSTEM ON if
you selected AWAY.
8.
The keypad next displays EXIT: ## INSTNT and begins to
count down the number of seconds remaining for you to
exit. The keypad will sound the exit delay alert when 20
seconds remain, and when the delay expires, all zones are
armed.
9.
You can select INSTNT while EXIT: ## INSTNT is displayed
to immediately arm all zones and make them instant. The
keypad displays INSTANT.
10. When the system is fully armed, the keypad displays
PERIMETER ON for Perimeter arming, PERIM/INT ON for
Perimeter and Interior arming, and ALL SYSTEM ON for all
areas armed.
XR20 User’s Guide
Arming and Disarming
Home/Away System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the keypad sounds a prewarn tone
to remind you to disarm the system. You must disarm the system
before the prewarn tone expires or an alarm on the door will
occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones
that tripped or any communication problems that occurred during
the armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the
system disarms.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
Easy Exit™ Feature
While the system is armed, you can also just press COMMAND and
then the 9 key to restart the exit delays to allow you to exit the
premises without disarming the system. After the exit delay time
expires, the system rearms automatically. This feature allows you
to get the paper, let your pet out, or leave for work without having
to disarm and then rearm the system.
Arming and Disarming
Disarming a Home/Away System
1. During the entry delay, the keypad displays ENTER CODE:.
Enter your user code.
2.
The keypad then displays any alarms or communication
problems that occurred during the armed period.
3.
The keypad next displays ALL SYSTEM OFF to conÞrm the
system is disarmed.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user
code. The keypad displays DISARM SILENCE.
2.
Press the Select key under DISARM to disarm the system and
silence the alarm. The keypad next displays ALL SYSTEM
OFF to conÞrm the system is disarmed.
3.
Press the Select key under SILENCE to stop the bell or siren
but NOT disarm the system.
If you do not press any Select key, or you press the
COMMAND key, the system will automatically disarm and
silence the alarm.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this report
to the central station. Be sure that you want the alarm message
to be cancelled BEFORE deciding to disarm the system. If you do
not want to disarm the system and send the abort report, press
SILENCE to only turn off the alarm bells.
XR20 User’s Guide
13
User Menu
Many of the features of your system have been put into a User Menu
that you can access from any Security Command keypad. The menu
requires you to enter your user code and then it only shows those
functions to which you have access.
Accessing the User Menu
1.
Press the COMMAND key until MENU? NO YES displays.
2.
Select YES. The keypad displays ENTER CODE: –. Enter
your user code and press COMMAND. You can now scroll
down through the list of system features available to you.
User Menu Options
The list below shows the User Menu options in order:
Menu Option Description
USER CHECKIN
Allows monitoring of children coming home
from school.
SYSTEM TEST
Tests the system’s siren, communication to
the central station, and backup battery.
ACTIVITY CHECK
Monitor a zone for non-activity.
USER CODES
SENSOR RESET
Resets smoke or glassbreak detectors that
have latched due to an alarm condition.
Allows you to add, delete, or change user
codes and authority levels.
SCHEDULES
Allows you to add, remove, or change system
schedules.
TIME
Allows you change the Day, Date, or Time that
is currently in the system.
OUTPUTS ON/OFF
Allows you to turn on or off any of the outputs
described in the System Setup section of this
guide.
BYPASS ZONES
Allows you to Bypass a zone or reset an already
bypassed zone.
DISPLAY EVENTS
Allows you to view or print the last 200 system
events that occurred on your system.
ZONE MONITOR
Allows you to add or remove a zone from the
monitor mode.
SERVICE REQUEST
Allows you to send a message to the Central
Station requesting service on the alarm
system.
14
XR20 User’s Guide
Arming and Disarming
User Check-in
Zone Activity Check
User Code Level: Master or Standard
User Code Level: Master or Standard
Function: This feature allows you to monitor the arrival of children
from school or employees to work by having a special Check-in
Report sent to your alphanumeric or numeric pager. Your system
must be programmed for the Pager Direct™ option. The Appendix
section of this guide contains Quick Reference cards for your wallet
or purse.
Your security system may be programmed for the Zone Activity
Check feature to monitor a person for non-activity. This could be
used for a person living alone to detect when they have not tripped
a disarmed zone within a programmed period of time. This feature
can be programmed for you at any time.
Sending a Check-in Report
1. After disarming the system, access the User Menu.
You may also press the COMMAND + 7 and then enter your
user code to send a Check-in Report.
2.
At the USER CHECKIN? display, press any Select key. The
keypad displays USER CHECKIN: 22 ( 22 = user number).
3.
The panel sends the Check-in Report containing your
account number and user number to the pager.
Function: This option allows you to enable or disable the Zone
Activity Check which monitors your system for no zone activity.
When the programmed time period is exceeded because no activity
is detected, your keypads will sound a steady tone and display PRESS
ANY KEY. Pressing any key on the keypad restarts the no activity
programmed time period and prevents your system from sending a
“User Activity Not Detected” report to the central station.
Note: The Zone Activity Check is disabled when a schedule is
entered to allow for sleeping hours and is automatically enabled
when an area is armed or disarmed.
Selecting Zone Activity Check
1. At the ACTIVITY CHECK? display, press any Select key. The
keypad displays ENABLE? YES NO. The default is YES.
User Menu
2.
When NO is selected, the keypad displays CHECK DISABLED
for four seconds and then sends the Activity Check Disabled
message to the central station.
3.
When YES is selected, the keypad displays CHECK ENABLED
for four seconds and then sends the Activity Check Enabled
message to the central station.
XR20 User’s Guide
15
Sensor Reset
Outputs On Off
User Code Level: Master or Standard
User Code Level: Master or Standard.
Function: Resets smoke or glassbreak detectors. Also clears Fire
and Supervisory zone alarms and trouble keypad displays. Sensor
Reset also clears low battery displays if your system is using
wireless sensors.
Function: Allows you to turn the system’s outputs on and off.
Once smoke or glassbreak detectors have tripped, they must be
reset before they can detect any additional alarm conditions. When
Sensor Reset is selected, power to the detectors is temporarily
removed by the system allowing them to reset.
Make sure all smoke is cleared from around the area of the smoke
detectors before performing a Sensor Reset to prevent the alarm
from occurring again.
Resetting the Sensors
1. Access the User Menu.
2.
When SENSOR RESET? is displayed, press any Select key.
The keypad displays SENSORS OFF for Þve seconds followed
by SENSORS ON.
3.
The keypad returns to the status display.
Enter your user code to reset sensors
While your system is disarmed, you can just enter your user code
and press COMMAND to reset the sensors. (This feature operates in
All/Perimeter and Home/Away systems only.)
This also activates the door strike if your system has an Easy Entry™
access control keypad.
16
This function is used to individually turn your system’s relay
outputs on and off. Your system may use these outputs to control
interior and exterior lighting, or heating, air conditioning, or other
appliances.
The names and numbers of the outputs on your system are located
in the System Setup section at the back of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2.
Press the COMMAND key until OUTPUTS ON/OFF? displays.
3.
Press any one of the Select keys.
4.
The keypad displays OUTPUT: - ON OFF.
5.
Enter the output number you want to turn on or off. The
output number appears in the display.
6.
With the output number displayed, press the Select key
under ON or OFF. The output is then turned on or off,
depending on your selection, and remains in that state until
you change it.
7.
The system automatically removes the output number and a
new output number can be entered. Refer back to step 5.
To exit the Output menu option, press the Back Arrow key until you
have returned to the keypad’s Status List.
XR20 User’s Guide
User Menu
Bypass Zones
Zone Monitor
User Code Level: Master or Standard.
User Code Level: Master and Standard.
Function: Allows you to bypass a zone prior to arming the system.
Function: Allows the system to monitor selected disarmed zones
(doors, windows, or motion detectors). When a monitored zone
is tripped, the keypad sounds a tone and displays the zone name.
This is an ideal feature for monitoring door zones to tell when
someone comes in or goes out.
Bypassing is usually done when a zone cannot be restored to normal
and you want to arm the system. Once bypassed, the system will
not respond to any activity on the zone.
A zone can be bypassed only while it is disarmed. Since Fire, Panic,
Emergency, and Supervisory zones are always armed, they can
never be bypassed.
The Bypass Zones function can also be used to restore a bypassed
zone back into the system.
When Bypass Zones is selected, a report of the bypassing can be sent
to your central station. This is optional and can be programmed for
you at any time.
Using the Bypass Zones Function
1. Access the User Menu.
2.
Press the COMMAND key until BYPASS ZONES? displays.
3.
Press any one of the Select keys.
ZONE: - RST BYPS.
4.
To reset a zone, enter the zone number and press the Select
key under RST.
5.
To Bypass a zone, enter the zone number and press the
Select key under BYPS.
User Menu
The keypad displays
You can place any combination of disarmed zones in Zone Monitor
but only the most recent zone tripped is displayed. The displayed
zone name clears automatically after a short time or when the zone
is armed.
Zone Monitor does not function while the system is armed but
a zone placed into it will still be monitored when the system is
disarmed.
Using Zone Monitor as part of your weekly system test: After using
the System Test function, place all perimeter and interior zones in
Zone Monitor. Starting at the front door, go around and open and
then close each door and window. You should hear the keypad beep
each time. The keypad will also display the name of each zone as
its device is opened.
Once all protected doors and windows have been tested, walk in
front of each motion detector. The keypad should beep to conÞrm
their operation. If at any time during your weekly testing a device
does not cause the keypad to beep, call the service department for
assistance.
XR20 User’s Guide
17
Using the Zone Monitor Function
System Test
1.
Access the User Menu.
User Code Level: Master or Standard.
2.
Press the COMMAND key until ZONE MONITOR? displays.
3.
Press any one of the Select keys.
Function: System Test is used to test the battery, alarm bell or
siren, and communication to a central station. The System Test
function begins automatically as soon as you select it.
The keypad displays PERIM ALL NBR .
4.
Select PERIM to place all disarmed perimeter zones into
Zone Monitor. PERIM is displayed only on All/Perimeter and
Home/Away systems.
Using the System Test Function
1. Access the User Menu.
2.
Press the COMMAND key until SYSTEM TEST? displays.
3.
Press any one of the Select keys. The system test begins
automatically and the keypad displays:
4c. Select RMV to remove all perimeter zones.
1)
BELL SOUNDING during a two second bell test, then:
5.
2)
BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery, then:
4a. The keypad displays PERIM? ADD RMV.
4b. Select ADD to add all perimeter zones to Zone Monitor.
Select ALL to place all disarmed perimeter and interior
zones into Zone Monitor.
* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test, then:
5a. The keypad displays ALL? ADD RMV.
5b. Select ADD to add all disarmed zones to Zone Monitor.
5c. Select RMV to remove all disarmed zones.
6.
7.
Select NBR to enter a speciÞc zone number for zone
monitor.
If NBR is selected, the keypad displays ZONE : - ADD RMV.
7a. Enter any zone number and select ADD to add this zone.
7b. Enter any zone number and select RMV to remove the
zone.
8.
18
The zone number automatically disappears and a new zone
number can then be entered in step 7a.
4)
TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test, then:
5)
TEST END to indicate the System Test is complete.
6)
You can end the transmit test by pressing the Back Arrow
key.
* The transmit test does not operate on local systems.
Testing your system’s burglary protection: The System Test function
should be part of your weekly testing and should be followed by
placing the interior and perimeter burglary devices in Zone Monitor
mode. This allows you to open and then close each protected door
and window while listening for the keypad to beep conÞrming its
operation. See Zone Monitor.
XR20 User’s Guide
User Menu
User Codes
User Code Authority Levels
User Code Level: Master only.
Function: Allows you to add or delete a user from the system or
change their user code or authority level.
There are three characteristics associated with each user code:
There are three characteristics associated with each user code that
deÞne its capabilities within the system.
Characteristic
Example
User Number
12
User Code
3456
Authority Level
Master
User Menu Option
Standard
Master
Arm and Disarm
Sensor Reset
Outputs On/Off
Bypass Zones
Zone Monitor
System Test
Service Request
Display Events
Set Time
Schedules
User Codes
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
User Number - Your system supports 32 users. Each user is
numbered from 1 to 32. This number identiÞes them to the
system and is transmitted to the central station (if your system is
monitored) when they arm or disarm the system.
User Code - Users also have a 4-digit user code they enter into the
keypad when arming or disarming. This user code is kept secret
from other users and is not transmitted to the central station when
they arm or disarm.
Users enter only their own user code when operating the system.
Authority Level - The user is also assigned a level of authority
(Master or Standard) by the person administrating the system that
determines the functions they can access.
The table to the right lists system functions users are allowed to
access based on the authority level assigned to their codes at the
time they are added to the system.
User Menu
XR20 User’s Guide
19
Adding User codes
1. Access the User Menu. Press the COMMAND key until USER
CODES? displays.
6b. AREAS:
. (Displayed in Area systems only).
2.
Press any Select key. The keypad displays ADD DEL CHG.
Enter the area numbers where this user will have access.
For example: if you want this user to only have access to
areas 1 and 2, enter the numbers 1 and 2.
3.
Press the Select key under ADD to add a new user code.
(You must have a Master user level to add a user.)
Once the correct area numbers are shown, press
Command.
4.
At the USER NUMBER:
press COMMAND.
- prompt, enter a user number and
5.
The displays changes to CODE NO:. Enter the user code and
press COMMAND.
6.
The display changes to MASTER? NO YES. Select YES to
make this a Master user level with the authority to access
all User Menu functions.
Select NO to make this a Standard user level. The following
options can then be selected:
6a. TEMP CODE
NO YES.
6c. ARM ONLY
NO YES.
Select NO to allow this user to arm and disarm the system
and access all Standard level functions in the User Menu.
Select YES to restrict this user to arming only.
(The Arm Only user code can bypass zones not in a normal
condition at the time of arming.)
7.
After you have completed making your selections, the
keypad display shows USER # ADDED. Press the Back Arrow
key once to add another user or twice to exit the User
Menu.
Select NO to make this a permanent user code.
Select YES to make this a temporary code that automatically
expires in 7 days. Temporary codes are ideal for guests or
service technicians. You can delete a Temporary user code
at any time before the 7 day active period ends.
20
XR20 User’s Guide
User Menu
Deleting User codes
1. Access the User Menu.
Changing User codes
1. Access the User Menu.
2.
Press the COMMAND key until USER CODES? displays.
2.
3.
Press any one of the Select keys. The keypad displays ADD
DEL CHG.
3. Press any one of the Select keys. The keypad displays ADD
DEL CHG.
4.
Press the Select key under CHG to change a user code. You
must have a Master user code level to change a user code.
4.
5.
At the USER NUMBER: - prompt, enter the user number to
change and press COMMAND.
Press the Select key under DEL to delete a user code from
the system. You must have a Master user code level to be
able to delete a user code.
5.
6.
The display changes to CODE NO: * * * *. Enter the new
user code. If the code you entered is already in use, or is
a code used internally by the system, the keypad displays
ALREADY IN USE: You must enter a different user code.
At the USER NUMBER:
- prompt, enter the user number
you want to delete and press COMMAND. The displays
changes to USER # DELETED.
6.
The display then changes back to USER NUMBER: - for you
to delete another user. Press the Back Arrow key twice to
exit the User Menu.
7.
If you are changing a code other than your own, the keypad
next displays MASTER? NO YES. Select YES if you want this
user to have a Master authority level.
Select NO if you want this user to have a Standard authority
level. If you select NO, refer to item number 7 in the
Adding User Codes section on the previous page.
Note: Changing a user code does not change the user number. User
number two may have their user code changed from 1234 to 5678
but they are still user number two.
User Menu
Press the COMMAND key until USER CODES? displays.
Ambush Codes
Your system may be programmed to allow user number 1 to be
an Ambush code. The Ambush code functions identically to other
codes with the exception that it sends a silent alarm to the central
station. This silent alarm alerts the operator to a duress situation
at the premises and prompts the immediate notiÞcation of the
authorities.
Refer to the System Setup section of this guide to see if your system
is programmed for Ambush. If so, do NOT program a code for user
number 1 unless you intend to use the Ambush function.
XR20 User’s Guide
21
Schedules
Setting an Arming and Disarming Schedule
1. Access the User Menu.
User Code Level: Master only.
Function: The Schedules function allows you to program into the
system the times you normally turn your burglary protection on and
off each day of the week. This information can then be used by the
system to automatically arm or disarm the burglary protection.
You can also use the Closing Check/Extend feature with Schedules
to help ensure your system is armed by an authorized user at a
speciÞc time. This option sounds the keypad buzzer and displays
CLOSING TIME! when a schedule expires. Users still on the premises
are reminded to arm the system or extend the schedule to a later
time. If the system is not armed, or the schedule not extended, a
report can be sent to the central station and/or a pager.
2.
Press the COMMAND key until SCHEDULES? displays. Press
any Select key. The keypad displays PRM EXT. Press the
Select key under PRM.
3.
The keypad next displays the day of the week you want
the schedule to start as SUN MON TUE WED. Press the
COMMAND key to show the remaining days of the week and
then press the Select key under your choice.
4.
The keypad then displays OP (open) 00:00 PM MON followed
by CL (close) 00:00 PM MON and DELETE KEEP. Press the
Select key under DELETE.
The keypad displays OPENING TIME?. Press COMMAND. The
keypad now displays MON – : AM PM. Enter the time you
want the burglary protection to be turned off. Use a 12
hour clock only (00:01 to 11:59). Press the Select key under
AM or PM.
Your system provides you with two different types of schedules:
Permanent schedules are used for automatic arming and disarming
and always occur at the same time until you change or delete
them.
5.
The keypad then displays CLOSING TIME?. Press the
COMMAND key. The keypad then displays MON – :
AM
PM. If you want the schedule to be for consecutive days,
press the Select key under MON to increment the days of
the week. When the correct day is shown, enter the time
you want the burglary protection to turn on.
6.
To clear a schedule, press DELETE and then AM when the
opening time is requested.
Extend schedules allow an authorized user to extend the present
day’s permanent scheduled closing time.
Press the Back Arrow key to exit the User Menu.
22
XR20 User’s Guide
User Menu
Extending Schedules
Setting the Date and Time
1. Access the User Menu.
User Code Level: Master or Standard.
Function: This option allows users to extend today’s programmed
closing time schedule.
2.
Press COMMAND until TIME? displays. Press any Select key.
3.
The keypad displays the current day and time. press the
COMMAND key.
Extending a Closing Schedule
1. Access the User Menu.
2.
Press the COMMAND key until SCHEDULES? displays. Press
any Select key.
3.
The keypad displays PRM EXT. Press the Select key under
EXT.
The keypad displays – : AM PM. Enter in the new time
for the closing schedule to expire.
The keypad displays the current date. Press the COMMAND
key to make any changes.
4.
The display changes back to TIME DAY DATE.
5.
Press the Select key under DAY to change the day of the
week. The keypad displays SUN MON TUE WED. If the
current day is not displayed, press the COMMAND key. Press
the Select key under the correct day.
6.
Press the Select key under DATE to change the date. The
keypad displays:
Extending the Schedule at CLOSING TIME! Display
1. Press any Select key. The keypad displays ENTER CODE:-.
2.
Enter your code and press COMMAND. The system’s
schedule is automatically extended one hour.
3.
The keypad then displays -: AM PM. You can enter a time
to extend the schedule for any time other than the default
one-hour extension. Press AM or PM.
Note: If the system is not armed by the scheduled closing time, a
Late to Close report is sent to the central station. If the schedule
is extended, a Schedule Change report is sent.
Date and Time
The keypad displays TIME DAY DATE. Press the Select key
under TIME to change the time. The keypad displays – :
AM PM. Enter the current time and select AM or PM.
MONTH: - Enter one or two digits for the month. Press
COMMAND.
DAY: - Enter up to two digits for the day. Press COMMAND.
YEAR: - Enter up to two digits for the year.
COMMAND.
Press
The display returns to TIME DAY DATE. Press the Back Arrow
key to exit the User Menu.
User Code Level: Master only.
Function: Allows you to change the current date and time
displayed on the keypad and used by the system for schedules and
Display Events.
User Menu
XR20 User’s Guide
23
Display Events
Service Request?
User Code Level: Master or Standard.
User Code Level: Master only
Function: Allows you to review up to 100 past events that occurred
on your system from any keypad. Once 100 events are stored, any
new event causes the oldest event to be cleared.
Function: Allows you to send a Request for Service message to the
central station when there is a problem on your system.
Note: This section shows the User’s Guide Display Events items for
both 16-character (single line) and 32-character keypad displays.
While in the Display Events function, use the COMMAND and Back
Arrow keys to go forward or backward through the list of events.
Using the Display Events Function
1. Access the User Menu.
2.
Press the COMMAND key until DISPLAY EVENTS? displays.
Press any Select key.
3.
The keypad displays FIRST LAST.
Select FIRST to view events starting from the oldest to the
newest. If you select FIRST, use the COMMAND key to scroll
up through the events displays.
After the Display Events function in the keypad User Menu, you
will see the SERVICE REQUEST? display if it has been programmed
for your user code. If this feature has been programmed, and
you would like to send a Request for Service report to the central
station, press any top row Select key while SERVICE REQUEST? is
displayed. After the Request for Service report is sent, the keypad
displays REQUEST MADE for four seconds.
If there is a problem with the telephone line connected to the
system, you must contact our service department directly for
assistance.
Note: This feature is not displayed if it has not been enabled on
your system.
Select LAST to view events starting from the newest to the
oldest. If you select LAST, use the Back Arrow key to scroll
down through the event displays.
The system’s memory can hold a maximum of 100 events for 45
days. Any event older than 45 days is cleared automatically by the
system. Also, once the full 100 events are stored, any new event
causes the oldest event to be cleared.
24
XR20 User’s Guide
User Menu
System Setup Record
System Setup
Area Names and Numbers Record
We have provided this System Setup section to allow you to track
the current and future status of the programmable options on your
Security Command system. If you make changes to the system, you
should update the information contained on these pages.
Your system is monitored by a central station.
! Yes
! No
C/S Name: _________________________________________
Address: ___________________________________________
Area Name
1
___________________________________________________
2
___________________________________________________
3
___________________________________________________
4
___________________________________________________
Output relays
City/State: __________________________________________
Your system has 4 outputs that can be used for various functions.
Below is a list of these outputs and the devices they control.
Emergency Phone: ___________________________________
Output #
Service Phone: ______________________________________
Service Manager: ____________________________________
Your system sends Opening and Closing reports.
! Yes
! No
Your system sends Zone Bypass reports.
! Yes
! No
Your system sends Ambush reports.
! Yes
System Setup
What it Controls
1
_____________________________
2
_____________________________
3
_____________________________
4
_____________________________
Use the Output number in the User Menu when setting Output
Schedules or using the Outputs On Off option to manually toggle
the relays.
! No
XR20 User’s Guide
25
User Codes
Your system provides 32 user codes you can program for individual
users. As you add new users or change current users’ codes, you
can keep track of their name, user number, and other information
here in this section. Use a pencil to allow for changes.
HOW TO FILL IN THIS TABLE
User - The User Number of the person authorized to use the
system.
Level - Master or Standard authority.
Temp Code - Is this code set to expire after seven days?
All Areas - Does this user have the authority to arm and disarm all
areas in the system?
Arm Only - Is this user restricted to just arming?
Refer to the User Codes section of this User’s Guide for additional
information.
Circle your Selections.
26
User
User Name
Level Areas Arm Only
1
M S
1234
Y N
2
M S
1234
Y N
3
M S
1234
Y N
4
M S
1234
Y N
5
M S
1234
Y N
6
M S
1234
Y N
7
M S
1234
Y N
8
M S
1234
Y N
9
M S
1234
Y N
10
M S
1234
Y N
11
M S
1234
Y N
12
M S
1234
Y N
13
M S
1234
Y N
14
M S
1234
Y N
15
M S
1234
Y N
16
M S
1234
Y N
XR20 User’s Guide
System Setup
User
User Name
Level Areas Arm Only
HOW TO FILL IN THIS TABLE
User - The User Number of the person authorized to use the
system.
17
M S
1234
Y N
18
M S
1234
Y N
19
M S
1234
Y N
20
M S
1234
Y N
21
M S
1234
Y N
22
M S
1234
Y N
Refer to the User Codes section of this User’s Guide for additional
information.
23
M S
1234
Y N
Circle your Selections.
24
M S
1234
Y N
25
M S
1234
Y N
26
M S
1234
Y N
27
M S
1234
Y N
28
M S
1234
Y N
29
M S
1234
Y N
30
M S
1234
Y N
31
M S
1234
Y N
32
M S
1234
Y N
System Setup
Level - Master or Standard authority.
Temp Code - Is this code set to expire after seven days?
All Areas - Does this user have the authority to arm and disarm all
areas in the system?
Arm Only - Is this user restricted to just arming?
XR20 User’s Guide
27
About the Display Events Section
Appendix A
Zone Bypass Event Displays
This section of the User’s Guide shows the Display Events items for
32-character keypad displays. While in the Display Events function,
use the COMMAND and Back Arrow keys to go forward or backward
through the list of events.
This displays the bypassing of system zones.
16-Character Display
10
BYPS
12
1017
To view more information about each display, press the Select key
as directed in the explanations below.
32-Character Display
Zone Activity Check Event Display
This displays the date and time the Zone Activity Check was
enabled or disabled.
16-Character Display
ACT ENABLED 2
1017
32-Character Display
5:18P 10/17
10/ 17
ACT DISABLED
Description
The Zone Activity Check was
enabled on October 17.
Description
The Zone Activity Check was
disabled on October 17, at 5:18
PM.
Activity Check Event Types - There are 3 event types:
ACT DISABLED
28
ACT ENABLED
BYP
5:18P 10/ 17
EAST WINDOW
Description
Zone 10 bypassed by user 12.
Press the left Select key for the
zone name and the right Select
key for the time.
Description
The east window zone was
bypassed. Press a Select key
for the zone number and user
number. Press again for the
user name.
Bypass Event Types - There are 3 event types:
BYP - Bypass RST - Restore
FRC - Force Arm
Note: You may sometimes see the user as SWG. This is short for
Swinger Bypass which is an automatic function that allows the
system to bypass a zone.
NO ZONE ACTIVITY
XR20 User’s Guide
System Setup
Zone Event Displays
Arming and Disarming Event Displays
This displays alarms, troubles, and other events that could occur on
your protection zones.
This displays any arming or disarming of system areas.
16-Character Display
2
BURG
ALR
1017
32-Character Display
ALR
10:23P
10/17
BASEMENT DOOR
Description
A burglary alarm occurred on
zone 2. Press the right Select
key for the time the alarm
occurred.
Description
An alarm occurred at 10:23 PM
on Oct. 17. Press any Select
key to see the zone number
and zone type.
Zone Type - There are 7 possible zone types you may see here.
FIRE - Fire
PANC - Panic
ARM
3
12
1017
32-Character Display
ARM
5:10P
WAREHOUSE
10/ 17
BURG - Burglary
EMRG - Emergency
SUPV - Supervisory
AUX1 - Auxiliary 1
AUX2 - Auxiliary 2
Event Types - There are 6 event types you may see here:
ALR - Alarm
16-Character Display
Description
Area 3 was armed by user 12
on Oct. 17. Press the Select
key under 3 for the area name,
under 12 for the user name, or
under 1017 for the time the
arming occurred.
Description
The area was armed at 5:10
PM. Press any Select key to
display the area number and
user number.
Arming Event Types - There are 2 event types you may see here:
ARM - User armed the system
DIS - User disarmed the system
TBL - Trouble
RST - Restore
FLT - Zone Fault
LOW - Low battery
MIS - Missing wireless transmitter
Note: LOW and MIS are for wireless systems only.
Appendix A
XR20 User’s Guide
29
User Check-in Event Displays
Supervisory Event Displays
This shows when a user selected the pager Check-in feature from
the User Menu. See page 15 for more information.
This displays the date and time of an automatic test report.
16-Character Display
CHECKIN 16 1017
32-Character Display
MSG 3: 31P 10 / 17
CHECKIN USER: 16
Description
User 16 selected the Checkin
feature on Oct. 17. Press the
right Select key for the Checkin
time.
Description
User 16 selected the Check-in
feature at 3:31 PM on Oct.17.
16-Character Display
AUTO RECALL
1017
32-Character Display
MSG
11:58P 10/ 17
AUTO RECALL
Description
The test report was sent on
Oct. 17.
Description
The test report was sent to the
central station at the date and
time shown.
System Monitor Event Displays
User Code Change Event Displays
This displays any addition, deletion, or change to a user code.
This displays any problems with the system’s AC power, battery, or
phone line or any opening of a tampered panel box.
16-Character Display
Description
User 12 added user 19 on Oct.
17. Press the right Select key
for the time this occurred.
16-Character Display
Description
User 19 added by user 12 at
11:41 AM.
32-Character Display
12
ADD
19
1017
32-Character Display
ADD
11:41A 10/ 17
US:19 BY
US:12
User Code Event Types - There are 3 event types you may see here:
ADD - User added
DEL - User deleted
CHG - User code or authority level has been changed.
30
POWER
TBL
1017
TBL
11:41A 10/ 17
POWER
Description
An AC failure occurred on Oct.
17. Press the Select key under
1017 for the time.
Description
An AC failure occurred at 11:41
AM. on Oct. 17.
System Monitor Event Types - There are 2 event types:
TBL - Trouble
RST - Restore
System Monitor Event Names - There are 2 system monitors:
AC POWER
XR20 User’s Guide
BATTERY
Appendix A
Appendix B
Easy Entry™ User’s Guide
This section of the user’s guide provides information on using the Easy Entry™ access control capability of the security command system.
If your system is not currently using any access control devices, disregard this section. Easy Entry™ is built into every Security Command
system and can be accessed using Easy Entry™ keypads.
There are three different operating modes: Door Strike, Arming and Disarming, and
Entry Delay. All of the examples below assume that your system requires a user code
to arm and disarm the protection.
DOOR STRIKE
Area and All/Perimeter Door Strike - From the Status List, present your
card to the reader.
Once it is validated by the system, the Door Strike
relay activates.
See Door Strike Relay Operation above.
Home/Away
systems only activate the Door Strike relay when arming and disarming.
ABC SECURITY
ARM
DISARM
POWER
While the keypad is in the Status
List, present your access card.
The relay activates for 5 seconds during
which time you can open the door.
Once you open the door, you have 40
seconds to exit and close the door before
the zone 2 Soft-Shunt expires.
ARMING AND DISARMING AN AREA SYSTEM
Press Command. The keypad displays ARM DISARM. Press the Select key under either option. The keypad displays ENTER CODE: -.
Present your card to the reader. Once it is validated by the system, all areas accessible by you arm or disarm automatically and the Door
Strike relay activates.
ABC SECURITY
ARM
DISARM
POWER
Appendix B
ABC SECURITY
ENTER CODE: –
POWER
ABC SECURITY
ALL?
NO YES
POWER
XR20 User’s Guide
31
ARMING AND DISARMING AN ALL/PERIMETER SYSTEM
Press Command. The keypad displays PERIM ALL (when arming) or DISARM?. Press the Select key
under the option. The keypad displays ENTER CODE: -.
PERIM
Present your card to the reader. Once it is validated by the system, both areas arm or disarm
automatically and the Door Strike relay activates.
ARMING AND DISARMING A HOME/AWAY SYSTEM
Home/Away system Arming and Disarming - Present your card to the reader. If the system is armed,
once the card is validated all areas are disarmed.
If the system is disarmed when you present your card, once it is validated all areas are armed in the
AWAY mode.
ENTRY DELAY
All Systems - Once the protected door is opened and the entry delay
starts, the keypad displays ENTER CODE: -. Present your card to the
reader and, once it is validated, the system disarms all areas accessible
by you and activates the Door Strike relay. Area systems provide a delay
to allow selected areas only to be disarmed. See Arming and Disarming
above.
Using the access reader for user menu access
You can also use a card reader to access the User Menu when the MENU?
NO YES display is shown.
32
ALL
or
DISARM?
POWER
ABC SECURITY
FRI
2:15 AM
POWER
ABC SECURITY
ENTER CODE: POWER
POWER
Access door is opened.
The system disarms the areas and activates the Door Strike Relay.
XR20 User’s Guide
Appendix B
Pager Direct™ User’s Guide
Pager Direct uses the reporting capability of your security system to dial your pager number and send reports much like someone sending
you a pager message. You can receive reports of alarms, troubles, or armings and disarmings of the system and know at a glance the
status of your system.
Area Names
Area Names
List your system’s area names and numbers below:
Area
Name
List your system’s area names and numbers below:
Area
Name
1
_______________________________________
1
_______________________________________
2
_______________________________________
2
_______________________________________
3
_______________________________________
3
_______________________________________
4
_______________________________________
4
_______________________________________
Service Department Phone: ____________________
Emergency Phone:____________________________
Central Station Phone: ________________________
Appendix B
Service Department Phone: ____________________
Fold
Emergency Phone:____________________________
Central Station Phone: ________________________
Pager Direct™
Pager Direct™
Security Command
Alphanumeric Paging
Security Command
Numeric Paging
XR20 User’s Guide
33
Numeric Pager Display
Account Message Always
Number
ID
Zero
Area
Always
Number
Zero
Whenever the system sends a message to your pager, it will always
send the account number Þrst to identify itself.
User
Number
Account Number
This number has been programmed into your Security
Command system as an identiÞer. Whenever the system
sends a message to your pager, it will always send the
account number Þrst to identify itself.
Message ID
This is always a single digit that describes the message.
1 = Zone Alarm
5 = Late to Close
2 = Zone Trouble
6 = User Check-in
3 = Area(s) Arming 7 = Local Message
4 = Area(s) Disarming
Typical Zone Event Display
20002
001 NORTH DOORS
BURG *ALARM* SHIPPING
Account Zone
Zone Name
Zone Type Event
Area Name
Zone Types - BURG, FIRE, SUPV (Supervisory), PANC (Panic),
EMRG (Emergency), AUX1, or AUX2
Events - ALARM or TROUBLE
Typical Arming/Disarming Display
20002
ARMED 0016 BILL SMITH
01 EAST WAREHOUSE
Account Event User # User Name Area #
Events - ARMED or DISARMED
20002 USER CHECKIN REPORT BY 0016
Zone, Area, or User Number
If this message is for a zone, the 1 to 3-digit zone number
is displayed.
20002
Security Command Numeric Paging
Area Name
User Check-in Display Description
Account Function Performed
User #
Functions - USER CHECKIN REPORT
If this message is for areas that are being armed or
disarmed, the area numbers are shown in sequential order.
Example: 1 2 4.
34
Alphanumeric Pager Display
Account Number
00128-3012340010
Typical System Event Display
LATE TO CLOSE
Account
Event
Events - LATE TO CLOSE (System not armed at its scheduled closing time)
ALARM CANCELLED (An alarm has been cancelled by an authorized user)
Security Command Alphanumeric Paging
XR20 User’s Guide
Appendix B
PhoneAccess™ User’s Guide
This exciting feature allows you to call your XR20 system from any outside touch-tone phone to arm and disarm protection areas or turn
on or off the panel’s relay outputs.
How it works
Quick Reference Wallet Card
From a touch tone phone, call the system’s phone number.
The XR20 answers and sounds a short ready tone. You now have
8 seconds to enter a valid Master user code. If the user code is
accepted by the panel, you will hear one or more beeps giving you
the current armed status of the system. (You can also Þnd out the
armed status of the system by pressing the * key at any time.)
If
All areas are armed
Area 1 (Perimeter) is armed
Any area is armed
All areas are disarmed
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
If the user code is not accepted by the panel, you will hear four short
beeps. Check the user code and try again. After 3 unsuccessful
attempts to enter the code, the panel locks out PhoneAccess™ until
a valid user code is entered at a keypad.
Once the user code is accepted by the panel and the armed status
is given, you can enter the following commands:
Press
#, 1
#, 2
#, 3
#, 0
#, 5, 4, 0, n*
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
1 short beep = on
1 long beep = off
4 short beeps = restricted
Note: Faulted zones are force armed when the area arms.
Appendix B
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
Disarm all areas*
Toggles the output
PhoneAccess™ Quick Commands
Press
#, 1
#, 2
#, 3
#, 0
#, 5, 4, 0, n*
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
Disarm all areas*
Toggles the output
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
1 short beep = on
1 long beep = off
4 short beeps = restricted
Note: Faulted zones are force armed when the area arms.
1. _________________________ 3. _________________________
2. _________________________ 4. _________________________
PhoneAccess™ Quick Commands
Press
#, 1
#, 2
#, 3
#, 0
#, 5, 4, 0, n*
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
Disarm all areas*
Toggles the output
You will hear
3 short beeps
1 short beep
2 short beeps
1 long beep
1 short beep = on
1 long beep = off
4 short beeps = restricted
Note: Faulted zones are force armed when the area arms.
1. _________________________ 3. _________________________
2. _________________________ 4. _________________________
XR20 User’s Guide
35
1.
Call the panel phone number.
sounds one short tone.
The panel answers and
2.
Enter your code within 8 seconds. One beep means the
code is good. Four short beeps means enter it again. You
have 3 tries.
3. You have 30 seconds to enter the Þrst command (see other
side) and 30 seconds for each additional command.
If
You will hear
All areas are armed
3 short beeps
Area 1 (Perim) is armed
1 short beep
Any area is armed
2 short beeps
All areas are disarmed 1 long beep
1.
Call the panel phone number. The panel answers and
sounds one short tone.
2. Enter your code within 8 seconds. One beep means the
code is good. Four short beeps means enter it again. You
have 3 tries.
3. You have 30 seconds to enter the Þrst command (see other
side) and 30 seconds for each additional command.
If
You will hear
All areas are armed
3 short beeps
Area 1 (Perim) is armed
1 short beep
Any area is armed
2 short beeps
All areas are disarmed 1 long beep
36
XR20 User’s Guide
Appendix B
FA113 User’s Guide
These instructions guide you through the operation of the XR20 Command Processor system using the FA113 Wireless Keychain Remote.
The FA113 uses the audible output capability of the Security Command keypad to sound conÞrmation tones. It is recommended that you
use the FA113 within hearing distance of these keypads.
Arming a Home/Away or All/Perimeter System
1. Press the ON button once to arm the Perimeter burglary protection. The Security Command keypads emit a single beep to conÞrm
the arming. The Perimeter arms and all non-priority zones not in a normal condition are force armed.
2. After the single beep, press the ON button a second time to arm the Interior burglary protection. The Security Command keypads
emit two beeps to conÞrm the arming.
3. After the two beeps, pressing the ON button in Home/Sleep/Away systems arms the Bedrooms burglary protection. The Security
Command keypads emit three beeps to conÞrm the arming.
Disarming a Home/Away or All/Perimeter System
Press the OFF button once. The Security Command keypads emit a single 2-second beep to conÞrm the disarming.
Arming an Area System
Press the ON button once to arm the following areas:
1. ___________________
2. ___________________
3. ___________________
4. ___________________
The Security Command keypads emit a single beep to conÞrm the arming.
Disarming an Area System
Press the OFF button once to disarm the above areas. The keypads emit a single beep to conÞrm the disarming.
Using the ALERT Buttons
Pressing the two ALERT buttons simultaneously sends a Panic alarm to the panel. If your system is monitored by a central station, the
proper authorities will be notiÞed of the alarm.
Appendix B
XR20 User’s Guide
37
Common Keypad Displays
Listed below are several keypad messages you may see on the display. Follow the instructions in the Possible Solutions column to
correct the problem. In many cases, you will need to call a service person to correct the problem. Displays that are not discussed here
mean that your service representative should be called.
Message
Tone at
Keypad
Invalid Code
No
Meaning
Possible Solutions
The user code you have entered is not recognized by the system.
Check the user code and try again.
Invalid Level
No
The code you have used does not have the authority level required
to perform the task you are attempting.
Check the user level to see if you have the correct level set for the
code. Remember that you can only grant a user authority is you
have the same authority or greater: You can’t give what you don’t
have.
Closing Time
Yes
The scheduled has expired but the area has not been armed.
Users still on the premise should arm the system or extend the
schedule to a later time.
Late to Close
Yes
The system was not armed at its scheduled closing time.
Users still on the premise should arm the system or extend the
schedule to a later time.
AC Trouble
Yes
The system is not getting proper power.
Contact your representative.
Battery Trouble
Yes
The battery is either low or missing.
Contact your representative.
Phone Line Trouble
Yes
The panel is looking for phone jack supervision.
Contact your representative.
System Trouble or
Service Required
Yes
There is a problem with one or more components in the system.
Contact your representative.
System Busy
No
The system is performing another task with a higher priority.
Wait a few moments for the system to complete the task.
4-Wire Bus Trouble
No
There is not a supervised device on the bus, low voltage or an
open yellow wire, or two devices share the same address.
Contact your representative.
Transmit Fail
Yes
The panel has not succeeded in communicating with the central
station.
Contact your representative.
38
XR20 User’s Guide
Appendix B
System Information
Use this space to record any additional information about your
system.
Appendix B
XR20 User’s Guide
39
Index
Symbols
B
2-Button Panic Keys 2
24-Hour Zone 5
Bypassing
when arming bad loops 2
A
C
ALARM display 4
Alarm Silence 15
All/Perimeter
Arming 10
Instant Arming 10
All/Perimeter System
Disarming 11
Alphanumeric Paging 33
Ambush Codes 21
Areas 5
Area Names and Numbers Record 25
Area System
Arming 8
Disarming 9
Arming 10
All/Perimeter 10
Home/Away 12
Central Station Monitoring 6
Changing User codes 21
Check-in Report to Pager 15
Common Keypad Displays 38
40
D
Date and Time 23
Delete User Codes 21
DIALING display 7
Display Events 24, 28
Door Access Event Displays 31
Supervisory Event Displays 30
System Monitor Event Displays 30
User Code Change Event Displays 30
Zone Bypass Event Displays 28
Zone Event Displays 30
XR20 User’s Guide
E
Easy Entry™ User’s Guide 31
ENTER CODE display 4
Entry or Exit Zone 5
Event Displays
Arming and Disarming 29
Event Displays 28
User Code Change 30
Zone Activity Check 24
Zone Events 29
Exit Error 6
Extended Schedules 23
F
FA113 User’s Guide 37
False Alarms 1
FAULT 7
H
Home/Away 12
Arming 12
Disarming During an Alarm 13
Easy Exit Feature 13
Index
I
P
Instant Arming 10
Instant Zone 5
Pager Direct™ User’s Guide 33
K
Keypad
2-Button Panic Keys 2
Data Entry Keys 2
Tones 3
User Menu 1
Keypad Displays
ALARM 4
DIALING 7
SYSTEM TROUBLE 4
L
LED
AC 2
Armed 2
U
R
Resetting the Sensors 16
S
Schedules 22
Extending a Closing Schedule 23
Security Command Keypad 1, 2
Security System Terms 5
Service Request? 24
Setting the Date and Time 23
Status List 6
System Setup Record 25
System Test 18
User Code
Authority Levels 19
User Codes 19, 26
Ambush Codes 21
Changing 21
Deleting 21
User Menu Options 14
Z
Zone 5
Bypassing 7
Zone Activity Check 15, 24
T
TROUBLE display 43
O
Outputs On Off 16
Index
XR20 User’s Guide
41
LT-0303 (5/03)

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project