advertisement
M1858C
18.5" Fanless Intel
®
Atom
TM
N2800 Infotainment Terminal
User's Manual
Version 1.0
P/N: 4012185801100P
1
2015.02
This page is intentionally left blank.
- 2 -
Revision History
Version Release Time
1.0
2015.02
Description
Initial release
- i -
Copyright
Copyright © 2015 ARBOR Technology Corp. All Rights Reserved.
This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequential damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages.
About This Manual
This user’s manual provides the general information and installation instructions for the product. The manual is meant for the experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this manual, consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference for any necessary maintenance in the future. Thank you for choosing ARBOR products.
- ii -
Contents
IEC 60601-1/EN60601-1/EN60601-1-2 .........................................................vi
Recommended Cleaning Procedures ............................................................xi
1.3.2 Optional Configuration (Configure-to-Order Service).............................3
Chapter 3 Using the Computer .................................................................19
3.1.1 Using the Function Keys on Windows .................................................20
3.1.2 Customizing Function Keys .................................................................21
- iii -
Contents
3.6 Using the Barcode Scanner (CTOS) .............................................................33
3.6.1 Supported Barcode Formats ................................................................35
3.7 Using the RFID&NFC Reader (CTOS) ..........................................................36
Appendix Optional Connections ..............................................................53
D. Using the Remote Controller and Nurse Call Function ...................................58
D.2 Connecting the Remote Controller .........................................................60
D.3 Programing Your Own Remote Controller Applications ..........................62
- iv -
Preface
Preface
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the directives of the Union European (EU). A Certificate of Compliance is available by contacting Technical Support.
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from ARBOR. Please contact your local supplier for ordering information.
FCC
This device complies with Part 18 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the guarantee of this device could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
- v -
Preface
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IEC 60601-1/EN60601-1/EN60601-1-2
• This product complies with the system standard IEC 60601-1 Medical
Electrical Equipment Part 1: General Requirements for Safety. And therefore, the product is exclusively interconnected with IEC 60601-1 certified equipment in the patient environment.
• Equipment connected to the analog or digital interfaces of the unit must comply with the respective IEC standards (e.g. IEC 60601-1 for medical equipment). Furthermore all configurations shall comply with the current version of the standard for SYSTEMS IEC 60601-1-1.
• Everybody who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore responsible that the system complies with current version of the requirements of the system standard IEC 60601-1-1. If in doubt, consult the technical service department or your local representative.
RoHS
ARBOR Technology Corp. certifies that all components in its products are in compliance and conform to the European Union’s Restriction of Use of Hazardous Substances in Electrical and Electronic Equipment (RoHS)
Directive 2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in electrical and electronic products. Member states of the EU are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed a maximum concentration value of 0.1% by weight or for cadmium exceed 0.01% by weight, per homogenous material. Homogenous material is defined as a substance or mixture of substances with uniform composition
(such as solders, resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
- vi -
Preface
SVHC / REACH
To minimize the environmental impact and take more responsibility to the earth we live, ARBOR hereby confirms all products comply with the restriction of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH
--Registration, Evaluation, Authorization, and Restriction of Chemicals) regulated by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
Intended Use
This product is intended for use in a medical system.
Symbol Descriptions
This “CAUTION” symbol indicates that there is a danger of injury to the user or a risk of damage to the product, should warning notices be disregarded.
Battery Recycle
This symbol of “Electrical Safety” indicates electrical warning of specific electrical hazards.
Refer to the user manual for more information.
Important Safety Instructions
Read these safety instructions carefully:
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or letting it fall may cause damage
3. Make sure the correct voltage is connected to the equipment.
- vii -
Preface
4. To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth.
5. For pluggable equipment, the socket outlet should be near the equipment and should be easily accessible.
6. Keep this equipment away from humidity.
7. Disconnect this equipment from the A/C outlet before cleaning it. Use a moist cloth. Do not use liquid or sprayed detergent for cleaning.
8. To fully disengage the power to the unit, please disconnect the power from the AC outlet.
9. Do not scratch or rub the screen with a hard object.
10. Never use any of the solvents, such as Thinner Spray-type cleaner, Wax,
Benzene, Abrasive cleaner, Acid or Alkaline solvent, on the display. Harsh chemicals may cause damage to the cabinet and the touch sensor.
11. Remove dirt with a lightly moistened cloth and a mild solvent detergent.
Then wipe the cabinet with a soft dry cloth.
12. The openings on the enclosure are for air convection and protect the equipment from overheating. DO NOT COVER THE OPENINGS.
13. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
14. If the equipment will not be used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.
15. Never pour any liquid into openings. This may cause fire or electrical shock.
16. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
17. No modification of the equipment is allowed.
18. Only personnel authorised by the manufacturer may carry out technical operations on the equipment.
19. The sound pressure level at the operator’s position, according to IEC 704-
1:1982, is no more than 70dB(A).
20. Keep this User’s Manual for later reference.
- viii -
Preface
21. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW
-20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE
EQUIPMENT.
22. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
Do not use the power adapter that isn’t made for the equipment.
Supplying the equipment with inappropriate voltage may cause harm to the battery (if any) or, even worse, burn the equipment.
Risk of explosion if RTC (Real-Time Clock) battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
General Cleaning Tips
You may need the following precautions before you begin to clean the device.
When you clean any single part or component for the device, please thoroughly read and understand the details below.
1. We strongly recommended that you should shut down the system before you start to clean any single components.
2. When you need to clean the device, please rub it with a piece of dry cloth.
- ix -
Preface
3. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor.
4. Never drop the components inside the device or get circuit board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning. Some individuals may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the device.
Cleaning Tools
Although many companies have created products to help improve the process of cleaning your devices and peripherals, users can also use household items to clean their devices and peripherals. Below is a listing of items you may need or want to use while cleaning your devices or peripherals. Keep in mind that some components in your device may only be able to be cleaned using a product designed for cleaning that component, if this is the case it will be mentioned in the cleaning.
• Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although paper towels or tissues can be used on most hardware as well, we still recommend you to rub it with a piece of cloth.
• Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the device. Unknown solvents may be harmful to the plastics parts.
• Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of the device can be one of the best cleaning methods. Over time, these items can restrict the airflow in a device and cause circuitry to corrode.
• Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations.
• Foam swabs: Whenever possible, it is better to use lint-free swabs such as foam swabs.
- x -
Preface
Recommended Cleaning Procedures
1. Close all application programs
2. Close operating software
3. Turn off the equipment
4. Remove all peripherals
5. Disconnect the power cable
6. Proceed to clean.
Disposing of the Equipment
•
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste.
This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself. The mark on electrical and electronic products only applies to the current European Union Member States.
•
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the
European Union, please contact your local authority so as to comply with the correct disposal method.
- xi -
Preface
Additional Information & Technical Support
All ARBOR products are built to the most accurate specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new equipment is destined for the laboratory or the factory floor, you can be assured that the computer will provide the reliability and ease of operation. Your satisfaction is our primary concern. We want you to get the maximum performance from the computer. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in the computer’s documentation.
These answers are normally a lot more detailed than the ones we can give over the phone. So please consult this manual first. If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from the computer.
In fact, most problems reported are minor and are able to be easily solved over the phone. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Do not hesitate to contact us using the following contact information:
Website: http://www.arbor.com.tw
E-mail: [email protected]
TEL: 886-2-8226-9396
Add: 10F., No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235,
Taiwan
- xii -
Warranty
This product is warranted to be in good working order during the warranty period. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, or inability to use this product. Vendor will not be liable for any claim made by any other related party.
Vendors disclaim all other warranties, either expressed or implied, including but not limited to implied warranties of merchantability and fitness for a particular purpose, with respect to the hardware, the accompanying product’s manual(s) and written materials, and any accompanying hardware. This limited warranty gives you specific legal rights.
Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.
- xiii -
This page is intentionally left blank.
- xiv -
Introduction
Chapter 1 Introduction
- 1 -
Introduction
1.1 Product Highlights
The medical infotainment terminal, M1858C, is designed for patient care and bedside infotainment. With low power consumption Intel
®
Atom™ N2800 processor and fanless design, the computer is suitable for the uses in hospitals and clinics. The M1858C is also an entertainment and information terminal for patients during their stay in hospital. The 18” touch screen, definable function keys and abundant expansions make it more convenient for clinicians and patients to operate. For networking, the M1858C supports Bluetooth and WLAN, which gives it great accessibility for eHealthcare medical care. Other integrated vertical application functions include 1D/2D barcode scanner, 5.0 megapixel camera, RFID &NFC reader and smart card reader.
•
Applicable for bedside Infotainment and self-registration
• Fanless operating with Intel
®
Atom™ processor N2800
• IEC60601-1 (3rd edition), EN60601-1 (3rd edition), EN60601-1-2 certified
• UL60601-1 compliant
• Ventless design, water-proof and dust resistant
• Patient identification through integrated RFID & NFC, barcode scanner and smart card reader
• Intel
®
SSD compatible
1.2 Package Contents
Upon opening the package, carefully inspect the contents. If any of the items is missing or appears damaged, contact your local dealer or distributor. The package should contain the following items:
1 x M1858C
1 x User’s manual
1 x Driver CD
- 2 -
Introduction
1 x 65W medical-grade AC/DC adapter kit
1.3 Ordering Information
M1858C
18.5” fanless Intel
®
Atom™ N2800 1.86GHz medical PC with flushmounted projected capacitive multi-touch screen
1.3.1 Optional Accessories
The following items are normally optional, but some vendors may include them as a standard package, or some vendors may not carry all the items.
Phone-1858
VoIP phone with RJ-11 cable
RC-185X
Remote controller with DB-9 cable
1.3.2 Optional Configuration (Configure-to-Order Service)
RFID & NFC-1858
RFID & NFC module kit
BarC-1858
Barcode scanner module kit
- 3 -
Introduction
1.4 Dimensions
499.7
336.5
45.3
Unit:mm
- 4 -
Introduction
1.5 Specifications
System
CPU
Graphic Controller
Smart Card Reader
Camera
Barcode Scanner
Phone
Remote Controller
RFID & NFC
Intel
®
Atom™ Processor N2800 dual-core 1.86GHz
Intel
®
GMA 3650
Memory
Chipset
2GB DDR3 SO-DIMM memory module installed
Intel
®
NM10
Storage
Peripherals and Devices
2.5” 32GB SATAII SSD installed
WLAN & Bluetooth 1 x WLAN 802.11 a/b/g/n & Bluetooth 4.0 LE, class 2
1 x Smart Card Reader slot
1 x 5.0 MP front-facing CCD camera
1 x 1D/2D Barcode Scanner (optional)
1 x VoIP phone blower (optional)
1 x Remote controller and VoIP phone (optional)
1 x 13.56MHz RFID & NFC reader with ISO
14443A/14443B/15693 support (optional)
I/O Interface
Audio
LAN
Serial Port
USB Port
Button & Indicator
2 x 3W speakers, 1 x built-in Microphone
1 x Mic-in, 1 x speaker-out on bottom Line
2 x RJ45 GbE connectors (one on bottom line, and the other on rear panel)
1 x RS-232 port on bottom line (DB-9 connector)
3 x USB 2.0 ports (two at the bottom, one at the rear)
Button
1 x Power on/off button
1 x Menu button
1 x Brightness up button
1 x Brightness down button
1 x Touch and LCD on/off button
1 x Volume up button
1 x Volume down button
1 x Phone on/off button
LCD Display
Size/Type 18.5" TFT color LCD
- 5 -
Introduction
Max. Resolution
Luminance
Contrast Ratio
1366 x 768 (WXGA) with 16.7M colors
1000 nits (typ.)
1000 : 1 (typ.)
Backlight Type
View Angle (U/D/R/L)
Touch Screen
Type
Light Transparency
LED
80°/80°/85°/85°
Projected Capacitive Multi-Touch Screen (Flush-mounted)
80% (typ.)
USB interface Controller Interface
Power Requirement
Adapter Input 100 ~ 240 VAC (full range)
Adapter Output DC 20V, 3.25A, 65W (Max.) with medical certificate
Mechanical & Environmental
Operating Temp.
Storage Temp.
0 ~ 40ºC (32 ~ 104ºF)
-20 ~ 60ºC (-4 ~ 140ºF)
Operating Humidity
Dimensions (WxHxD)
Vibration
Shock
Net Weight
Mounting
IP Rating
Operational Altitude
10 ~ 95% @ 40ºC (non-condensing)
558 x 337 x 66mm (21.97" x 13.27" x 2.6")
1 Grms/ 5 ~ 500Hz/ random operation
10G/peak (11ms)
5.0 kg (11.02 lb)
VESA-100 compatible (M6)
Compliance design with IP65 (front touch panel)
Below 2000m
Regulatory
CE, FCC Part 18 Subpart C
EN60601-1 (3rd edition), EN60601-1-2 certified
UL60601-1 compliant
No AP or APG Protection
Medical Device
Classification
Class I
Mode of operation
OS Support
Continuity
Windows Embedded Standard 7 (WS7E /WS7P)
Linux: Ubuntu / Fedora
- 6 -
Getting Started
Chapter 2 Getting Started
- 7 -
Getting Started
2.1 Getting to Know the Computer
Understanding the computer helps you jump seamlessly from component to component when using the computer. This section will quickly familiarize you with the computer.
2.1.1 Front View
Built-in Mic
5.0 Camera
Projected Capacitive
Multi-Touch Screen
Phone on/off
Volume down/up
Screen on/off
Power on/off
Menu
RFID & NFC (optional)
Brightness down/up
Function Key Graphic Default Function
Power on/off button
X
To turn on the computer: Press the button for about 3 seconds to turn on the computer.
X
To force shut down the computer: Press the button for about 10 seconds to force shut down.
Power on/off
X
To put the computer into hibernate or sleep mode:
Press the button for about 3 seconds until the LCD screen turns off.
X
To wake the computer from hibernate or sleep mode:
Press the button until the LCD screen turns on.
Note: The default action for the Power button in Windows
7 is sleep. To change the action, tapping Start > Control
Panel > Power Options > Power button action.
- 8 -
Getting Started
Function Key Graphic Default Function
Power on/off
Power Status LED
X
Off: The power is turned off and disconnected from a power source.
X
Lights green: The computer is turned on or in sleep/ hibernate mode.
X
Lights amber: The computer is turned off but connected to a power source.
Menu
Launches the ARBOR TabletUI utility.
Brightness up/down
Volume up/down
Screen on/off
Increases/decreases display backlight brightness.
Increases/decreases system volume.
Phone on/off
Turns on/off the display.
Turns on/off the phone handset audio.
Note: Phone handset function is disabled by default. To enable this function, enter the BIOS to enable “Phone
Button Configuration” under the Advanced menu. See
4.3 Advanced Settings on page 43
for details.
Caution: To power off the power completely, disconnect the plug of the AC power cord from the electrical outlet only when the power LED lights amber.
If you disconnect it while the power LED lights green, data might be lost or corrupted, and the system might be damaged.
- 9 -
Getting Started
2.1.2 Rear Side
VESA-100 Mounting Holes
VESA-75 Mounting Holes (DO NOT USE)
Item
VESA 100 mounting holes
DC-IN
LAN
Nurse Call Function
USB Port
Dual Speakers
DC-IN
LAN
Nurse Call Function
Dual Speakers
USB Port
Descriptions
To attach VESA 100-compatible mounting kit using M6 x 40 screws.
Warning: DO NOT use the VESA 75 mounting holes, or you might risk the danger of damaging the computer.
DC-IN Power jack.
To connect the computer to a power source through provided
AC power adapter.
Gigabit Ethernet port.
To connect the computer to a network through an Ethernet cable.
RJ-11 connector. To connect to a nurse call system.
For more information on using the nurse call function, refer to D.
Using the Remote Controller and Nurse Call Function on page
USB 2.0 Type-A port. To connect to USB device
Integrated 3W stereo speakers for audio output.
- 10 -
Getting Started
Warning: The computer’s rear plate is highly heated when the computer is operating. As the temperature might reach up to 60°C (140ºF), DO NOT touch the rear plate during operating.
2.1.3 Bottom Side
Barcode Scanner
(optional)
Speaker-out
Mic-in
Reserved (No function)
Item
Barcode Scanner
Phone Jack
USB Ports
Line-out
Mic-in
LAN
COM Port
Phone Jack
USB Ports
LAN
COM Port
(RS-232)
Remote Controller Port
(DB-9)
Descriptions
1D/2D barcode scanner (optional).
RJ-11 phone jack. To connect to a phone handset (optional).
USB 2.0 Type-A port. To connect to USB device(s).
To connect to a headphone for audio output.
To connect to a microphone to capture sound and voice when used with a program capable of recording audio.
Gigabit Ethernet port. To connect the computer to a network through an Ethernet cable.
RS-232 serial port. To connect to a serial device.
- 11 -
Getting Started
Item
Remote Controller
Port
Descriptions
DB-9 serial port. To connect to the optional remote controller through provided DB9-to-RJ45 cable.
For more information on using the remote controller, refer to
Using the Remote Controller and Nurse Call Function on page
2.1.4 Side View
Item
Smart Card Reader
Slot
Descriptions
Smart card reader slot with hinged rubber cover.
Allows to insert a smart card.
Smart Card
Reader Slot
- 12 -
Getting Started
2.2 Periodic Cleaning & Disinfection
This medical computer is generally employed in medical environment, for example, hospitals, as bedside infotainment. It is strongly recommended that users follow the cleaning and disinfection instructions described below to ensure proper maintenance activities.
1. Always power off your unit first when you clean or disinfect it.
2. To wipe the outer case, use lint-free cloth, lightly moistened with warm water and a mild, non-abrasive cleaning solution made of either:
• 70% isopropyl alcohol
• 10% bleach solution
• Dimethyl ethylbenzyl ammonium chlorides 0.125%, dimethyl benzyl ammonium chlorides 0.125%, Isopropyl alcohol 14.850% (Sani-Cloth®)
• Isopropanol 17.2%; Diisobutylphenoxyethyl dimethyl bezyl ammonium chlorides 0.28% (CaviCide®)
3. The touch screen can be wiped down (e.g. to remove fingerprints) during operation using standard computer screen solution.
4. Use dry cloth to clean the rear panel and bottom, especially the areas
around the connectors.
- 13 -
Getting Started
Caution:
• Do not spill liquids on or around the medical computer.
• Do not use other solutions than the ones mentioned above.
• Do not touch, press or rub the display panel with abrasive cleaning compounds, instruments, brushes, or rough-surface materials.
• Never spray cleaning liquids or foam onto the medical computer or soak it for cleaning.
• Do not use solvents to clean the unit.
• Do not clean, disinfect, or sterilize any part of the system by autoclaving or with the use of ethylene oxide gas; doing so may damage the unit.
• Never spray or squirt any type of liquid onto the medical computer; if a spray, gel or foam is needed, spray the liquid onto a cloth and then use the cloth to wipe or rub down the component.
• Always avoid contamination to minimize the need for disinfectants.
• Do not spill, spray, or squirt liquids to the power block and the power cable.
2.3 Drivers and Utilities Installation
The computer comes with a CD that contains device drivers as well as some programs and utilities. You need to install the drivers to activate the devices and some device-related services. Some drivers will come with driver-related programs to facilitate the application. To install the drivers and utilities, make sure to follow the instructions (e.g., the installation sequence) given in this section to proceed.
In addition, the CD includes a number of optional utilities. You may install those utilities as needed.
- 14 -
Getting Started
2.3.1 CD Contents
The drivers and utilities included in the provided CD are described in the table below:
Driver/Utility
Chipset
VGA
LAN
Audio
WiFi
Bluetooth
CCD Codec
RFID
Smart Card
Function Keys
Necessity
Required
Required
Required
Required
Required
Required
Descriptions
Install the chipset driver to the computer.
Make sure to install the chipset driver before installing other drivers to prevent errors.
Install the graphic driver.
Install the network device driver.
Install the audio driver.
Install the wireless network device driver. You may optionally install the wireless connection manager utilty.
Install the Bluetooth device driver. You may optionally install the Bluetooth suite utility.
Install the video capture/convertion tool. Optional
Required for
RFID/NFC module
Required
Install the RFID/NFC device driver.
Recommended
Install the smart card reader driver.
Install the ArborFunKey utility to use the functions on Windows or to customize the function keys.
For more information on using the utility, refer
to 3.1 Using the Function Keys on page 20 .
2.3.2 Installing the Drivers & Utilities
Before installing the drivers and utilities, make sure to:
• Prepare a USB CD-ROM drive
• Prepare a USB keyboard or USB mouse to navigate through the installation
• Lon on as an administrator
• Exit other running applications
Then follow the steps below to install the drivers and utilities.
- 15 -
Getting Started
1. The computer comes with two USB ports. Connect the USB CD-ROM drive (not provided) and the USB keyboard (or mouse) to the computer.
According to your CD-ROM drive, you may need to connect it to a power supply. or
2. Insert the provided CD to the CD-ROM drive. In a few seconds, a dialog box opens asking what to do with the disc. Tap Run AUTORUN.EXE to auto-run the driver CD.
3. Tap Driver Install.
- 16 -
4. The drivers menu then opens.
Getting Started
5. Follow the sequence below to install the drivers and utilities:
Chipset → VGA → LAN → Other Drivers / Utilities
The installation process of each driver is basically the same. Just follow the on-screen instructions to proceed. If prompted to restart the computer, tap
Yes to do so. In some cases, User Access Control will appear asking for permission to make changes to the computer. Simply tap Yes to continue.
- 17 -
This page is intentionally left blank.
- 18 -
Using the Computer
Chapter 3 Using the Computer
- 19 -
Using the Computer
the essential features of the computer.
3.1 Using the Function Keys
3.1.1 Using the Function Keys on Windows
To use the function keys, you can directly press the keys on the front bezel below the LCD viewing screen. Or, you can launch the
ArborFunKey control
UI on the Windows by either of the following methods:
1. Tap the up arrow in the system tray to show the ArborTabletui icon.
ArborTabletUI icon
Note: If you didn’t find the icon in the notification area, make sure the utility is running by tapping Start > All programs > Arbor MSeries >
ArborTabletui.
2. Tap the ArborTabletui icon. Then the Tablet PC Control UI will appear on the lower right corner of the desktop.
- 20 -
Using the Computer
The UI provide the following functions:
Icons Descriptions
To decrease system volume.
Close
To increase system volume.
To decrease LCD backlight brightness
To increases LCD backlight brightness
To enable/disable barcode scanner (configure-to-order).
Note: The barcode scanner is disabled by default and can be enabled by accessing BIOS > Advanced.
To mute/enable system audio.
To restore the defaults.
The volume and LCD brightness will be restored to the default levels, and all customized function keys will restore to the default functions.
To exit the Tablet PC Control UI.
3.1.2 Customizing Function Keys
Using the ArborTabetUI, you can also customize the function keys as needed.
The keys you can re-assign a function include Phone, Down, Up and Menu.
Other keys cannot be re-assigned with new functions.
- 21 -
Using the Computer
The table below summarizes the keys you can customize and the default functions:
Graphic Name
PHONEONHOOK
PHONEOFFHOOK
DOWN
Default Function
With the phone function being disabled in BIOS, no function is available to the key.
With the phone function being enabled in BIOS, press the key to toggle the phone on/off.
To decrease system volume.
UP To increase system volume.
MENU To show Tablet PC Control UI.
To customize your own function keys:
1. Tap the up arrow in the system tray to show the ArborTabletui icon.
ArborTabletUI icon
Note: If you didn’t find the icon in the notification area, make sure the utility is running by tapping Start > All programs > Arbor MSeries >
ArborTabletui.
- 22 -
Using the Computer
2. Tap and hold the icon to display the context menu and select
Set Function
Keys.
3. For the key that you want to customize its function, tap the drop-down list to choose a new function. Available functions include: Brightness Up,
Brightness Down, Volume Up, Volume Down, Show TabletUI, Show
OnScreenKeyboard, Read Barcode, Toggle Phone On and Toggle
Phone Off.
- 23 -
Using the Computer
Or, you can select Program and then tap Browse to specify an application that you want to associate with the key.
4. The settings take effect immediately. If you want to restore the defaults for all the keys, launch the Tablet PC Control UI and then tap Restore
Defaults.
3.2 Using the Wi-Fi Feature
The computer comes with a built-in Wi-Fi module for Wi-Fi networking. Once
the driver is installed as described in 2.3 Drivers and Utilities Installation on page 14
, the
Qualcomm Atheros Wireless Network Connection
Manager Utility is also installed on your computer for you to manage the wireless connections.
Alternatively, you can use the Windows Wireless Utility Manager to manage your wireless connection as described below.
1. Tap the network icon ( ior ) in the system tray.
2. A list opens and shows the Wi-Fi hotspots available within the wireless coverage of the computer.
- 24 -
Using the Computer
3. Tap the desired network to connect to it.
If the network to connect is a secured network, a dialog box will open and request for the password. Enter the password to access the Wi-Fi network.
If it is an open network, it will be connected in a few seconds.
- 25 -
Using the Computer
4. When the computer is connected to a Wi-Fi network, “Connected” will be displayed and the Wi-Fi signal strength icon in the notification area changes to .
3.3 Using the Bluetooth Feature
Bluetooth enables the wireless connection over a short distance about 8 meters. It is specified as a “wireless personal area network” (WPAN). The computer is Bluetooth-enabled to synchronize data with other Bluetoothcapable devices such as PCs, laptops, hands-free, headsets, printers, PDAs and cell phones.
Once the Bluetooth driver is installed as described in
, a Bluetooth utility, BlueSoleil, is also installed on your computer. To connect to a Bluetooth device using the utility, follow the steps below to proceed:
- 26 -
Using the Computer
1. Tap the up arrow in the system tray to show the Bluetooth icon.
Bluetooth icon
2. Tap and hold the icon to display the context menu and select
Add a
Device.
3. Select the device you want to pair and click
Next to proceed.
- 27 -
Using the Computer
4. Check the pair code on the device you want to pair and click Next to proceed.
5. The device has been added to this computer. To setup the device, click the
Bluetooth icon on the system tray and select Show Bluetooth Devices to proceed.
- 28 -
Using the Computer
3.4 Using the Camera Feature
The computer comes with a ready-to-use camera without the need to install additional drivers. You can use Windows or third-party camera utility with the camera to take pictures, record videos or participate in a video conference.
Or, alternatively you can use the LEAD MULTIMEDIA CONVERTER camera utility, which is installed when you install the camera driver, to test if the camera functions properly. To launch and use the LEAD MULTIMEDIA CONVERTER camera utility:
1. Tap
Start > All programs > LEAD Converter> LEAD Converter.
2. Tap the upper-left corner to switch to Capture mode.
Tap to switch to CAPTURE mode
CAPTURE mode
- 29 -
Using the Computer
3. Set the destination for saving the recorded video. Tap the DESTINATION box to select a folder and specify a name for the video. Then tap
PREVIEW.
Specify a destination and file name
Tap
Preview
4. A video preview window will pop up showing the video that the CCD camera is recording.
- 30 -
Using the Computer
3.5 Using the Smart Card Reader
The computer is equipped with one smart card reader with a hinged rubber cover, allowing users to provide identification and information using a smart card.
You may use your own Smart Card Reader application. However, you can optionally use the test program included in the driver CD to test if the smart card readers function properly. To use the test program,
1. Execute the file DEMO4.exe from the following path: disk drive:\Windows 7\SmartCardReader Driver\
2. Insert a smart card into the card reader that you want to test with the golden chip facing you.
- 31 -
Using the Computer
3. Tap Select reader. Detected reader will be displayed in the Select Reader dialog box. Select the reader that you want to test and then tap OK.
4. Tap Connect to proceed. If a smart card is successfully detected, its information will be displayed.
- 32 -
Using the Computer
3.6 Using the Barcode Scanner (CTOS)
The barcode scanner is a Configure-to-Order Service (CTOS) on the computer and it is disabled by default. To use it, you must enable it in BIOS. Once enabled, it can be triggered by the barcode scanner button in the
Tablet PC
Control UI. You can also customize a function key using the Arbor Tablet UI.
This section will walk you through the basic operations of the barcode scanner.
To get the information on supported barcode formats, see 3.6.1 Supported
on page
1. To use the barcode scanner, enter BIOS > Advanced and enable the device first since the device is disabled by default.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Legacy OpROM Support
Launch PXE OpROM [Disabled]
Enable or Disable Boot Option for Legacy Network Devices.
Barcode scanner Configuration
Phone Button Configuration
CPU Configuration
IDE Configuration
Super IO Configuration
[Disabled]
[Disabled]
Barcode Scanner Configuration
Disabled
Enabled
→←
: Select Screen
↓↑
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
2. Launch your barcode own application. Or, if you simply want to perform a test:
• To scan a 1D barcode: Launch a text editor, e.g., Windows Notepad.
• To scan a 2D barcode: Launch a web browser.
- 33 -
Using the Computer
3. Trigger the barcode scanner by using the barcode scanner button in the
).
Note: The scanning light will stay on for 12 seconds. If no barcode is within the reach of the scanning light and no barcode is read within the 12 seconds, the scanning light will auto-stop when 12 seconds elapse.
4. Position a test barcode a few inches from the scanner as the picture below shows.
5. According to the barcode scanned, the scanned data is displayed in the text field (1D barcode) or an action is triggered (2D barcode)
- 34 -
Using the Computer
3.6.1 Supported Barcode Formats
Linear
BC412 (requires end-user license from
IBM)
China Post
Codabar (NW7)
Code 11
Code 128
Code 32
Code 39
Code 93 and 93i
Code 2 of 5
EAN
Interleaved 2 of 5
Label Code
Matrix 2 of 5
MSI
Plessey
PosiCode
GS1 DataBar (formerly RSS)
Telepen
Trioptic Code
UPC
Stacked
Codablock F
Code 16K
Code 49
GS1 Composite (formerly EAN/UCC)
MicroPDF417
PDF417
TCIF Linked Code 39 (TLC39)
Matrix
Aztec
Chinese Sensible Code (Han Xin Code)
Data Matrix
Grid Matrix Code
MaxiCode
QR Code
Micro QR Code
Postal
Intelligent Mail Barcode
(formerly 4-state customer barcode)
Australian Post
British Post
Canadian Post
ID-tag (UPU 4-state)
Japanese Post
Netherlands (KIX) Post
Korea Post
Planet Code
Postnet
OCR
OCR-A
OCR-B
OCR MICR (E 13 B)
- 35 -
Using the Computer
3.7 Using the RFID&NFC Reader (CTOS)
The RFID&NFC reader is a Configure-to-Order Service (CTOS) on the computer and can be identified by a label on the lower right corner of the front bezel.
Once the driver for the RFID&NFC reader is installed, then it is ready for use.
You may use your own RFID&NFC application. However, you can optionally use the test program included in the driver CD to test if the reader functions properly.
To use the test program, firstly you have to identify the COM port used by the
RFID&NFC module by using the
Device Manager on Windows. To do so, t ap
Start > Control Panel > Hardware and Sound > Device Manager. Expand the Ports
(COM & LPT) section and locate the Silicon Labs CP210x USB to UART Bridge to identify the COM port.
- 36 -
Using the Computer
Then you may proceed to use the test program:
1. Execute the file
Jogtek.exe from the following path: disk drive:\Driver\RFID\Jogtek
2. The test program then opens. On the HF UID tab, select and open the
COM port that is used by the RFID&NFC module. Then select the card type(s) of the card you want to test. b. Toggle it to open the port a. Select the COM port used by the RFID&NFC device c. Select the card type(s)
3. Tap the RFID/NFC card to the reader.
- 37 -
Using the Computer
4. Then read and decoded data will be displayed.
- 38 -
BIOS
Chapter 4 BIOS
- 39 -
BIOS
A BIOS (Basic Input/Output System) is a special utility usually stored in the
ROM on the motherboard inside a computer. When you turn on the computer, the BIOS is immediately activated. During the startup, it checks and loads necessary information to ensure the computer can proceed with loading the operating system. The BIOS Setup Utility is typically accessed with a special key sequence, such as “Delete” or “Esc” key as soon as the computer is powering up.
Once you have entered the BIOS, you can get some system information and configure some hardware parameters. In most cases, there will be no need to make adjustments to the BIOS. The default settings apply to most applications and provide optimal performance.
Caution: If you need to make any change, be careful when making changes to the BIOS. Incorrect settings can cause system boot failure or malfunction.
Note: For system stability and performance, this BIOS utility is constantly improved. The screenshots demonstrated and descriptions hereinafter are for reference only and may not exactly meet what is presented on-screen.
4.1 Accessing the BIOS Setup Utility
To enter and use the BIOS Setup Utility, prepare a USB keyboard first and then:
1. Connect the USB keyboard to the computer first.
2. Power on the computer and press the “ Delete” or “Esc” key immediately after powering on.
3. Then you will enter the BIOS Setup Utility and see the Main setup screen.
BIOS Setup Utility is mainly a key-based navigation interface. The bottom of the screen shows the keys for navigation and changing the settings. Refer to the table below for instructions on using the keys.
Keys
F1
← →
Descriptions
Activate “General Help” screen.
Move to select a particular configuration screen from the top menu bar / Move to highlight items on the screen.
- 40 -
Keys
↓ ↑
Enter
Esc
+ / F6
- / F5
F9
F10
BIOS
Descriptions
Move to select an item.
Select or enter a submenu
On the Main Menu – Exit the setup and not save changes into
CMOS.
On the
Sub Menu – Exit current page and return to main menu.
Increase a numeric value.
Decrease a numeric value.
Load the optimal defaults. All settings will be set to the optimal defaults at startup.
Save the changes that have been made and exit the BIOS Setup
Utility.
4.2 Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. It reports basic system information and also allows you to configure the
System Date and System Time settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Set the Date. Use Tab to switch between Date elements.
Access Administrator
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
- 41 -
BIOS
The Main setup screen provides the following information and options:
Info / Item
BIOS Vendor
Core Version
Compliancy
BIOS Version
EC Version
System Date
System Time
Access Level
Descriptions
Displays BIOS vendor name.
Displays current core version information.
Displays the compliant UEFI (Unified Extensible Firmware
Interface) and PI (Platform Initialization) information.
Displays the computer’s model and the BIOS version.
Displays the current version of the Embedded Controller.
Sets system date. Valid range is from 1 to 12, 1 to 31 and
2000 to 2099.
Sets system time. Valid range is from 0 to 23, 0 to 59 and
0 to 59.
Displays the access level.
- 42 -
BIOS
4.3 Advanced Settings
The Advanced screen provides you the options to configure the details of your hardware, such as the barcode scanner, phone button, CPU, IDE and Super IO
(input/output).
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Legacy OpROM Support
Launch PXE OpROM [Disabled]
Enable or Disable Boot Option for Legacy Network Devices.
Barcode scanner Configuration
Phone Button Configuration
CPU Configuration
IDE Configuration
Super IO Configuration
[Disabled]
[Disabled]
→←
: Select Screen
↓↑
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Info / Item
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Launch PXE OpROM
Barcode scanner configuration
Phone Button
Configuraton
CPU Configuration
IED Configuration
Descriptions
Enables/Disables boot option for legacy network devices.
Options: Enabled, Disabled [default]
*PXE means “Preboot Execution Environment”, a series of methods to get a typical Windows-based computer to boot up without a hard drive or boot diskette.
Enables/Disables the barcode scanner (for model with barcode scanner module).
Options:
Enabled, Disabled [default]
Enables/Disables the phone handset function.
Options:
Enabled, Disabled [default]
Refer to 4.3.1 CPU Configuration on page 44
Refer to 4.3.2 IDE Configuration on page 45
- 43 -
BIOS
Info / Item Descriptions
Super IO Configuration Refer to 4.3.3 Super I/O Configuration on page 46
Caution: Be careful when making system and hardware changes. Incorrect settings can cause system boot failure or malfunction.
4.3.1 CPU Configuration
Access this submenu to view the CPU information and its capabilities, including the CPU’s model name, processor speed, microcode revision, max./min. processor speeds, processor cores, and so on.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
CPU Configuration
Processor Type
EMT64
Intel(R) Atom (TM) CPU
Supported
Speed
System
Ratio Status
Actual
System
14
Speed
Processor
Microcode
L1
L2
Revision
RAM
RAM
Core Dual
Supported
Hyper-Threading
Execute Bit
Limit CPUID Maximum [Disabled]
→←
: Select Screen
↓↑
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
- 44 -
4.3.2 IDE Configuration
Access this submenu to view the harddisk information.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA Port 0 MRSAJ5D032GC22 (32.0G
Misc Configuration for hard disk
BIOS
: Select Screen
: Select Item
Enter : Select
+/: Change Opt.
F1 : General Help
F2 : Previous Values
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
- 45 -
BIOS
4.3.3 Super I/O Configuration
Access this submenu to configure the system’s serial port.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Super IO Configuration
Set Parameters of Serial Port
0 (COMA)
Super
Serial Port 0 Configuration
Serial Port 1 Configuration
Power On after Power Fail [Power off]
→←
: Select Screen
↓↑
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
The Super IO Configuration screen provides the following setting options:
Settings
Serial Port 0/1
Configuration
Power On After
Power Fail
Descriptions
Configures the system’s serial port (COM port). The settings include:
Serial Port: Enables/disables the serial port.
Options: Enabled [default], Disabled
Device Settings: Shows the I/O and IRQ address of the
COM port.
Change Settings: Select an optimal setting for Super IO device.
Specify what state to go to when power is re-applied after a power failure.
Options: Power off [default], Power on
- 46 -
BIOS
4.4 Chipset
Access the Chipset menu and then select Host Bridge to view the system’s memory information.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Host Brdge
Chipset Boot Security Save & Exit
Host Bridge Parameters
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
******* Memory Information *******
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
- 47 -
BIOS
4.5 Boot
Access this menu to change system boot settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Boot Configuration
Bootup NumLock State [On]
Select the keyboard NumLock state.
Boot Option Priorities
Boot Option #1
Hard Drive BBS Priorities
[SATA PM: MRSAJ5D0...]
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
The Boot screen provides the following setting options:
Settings
Bootup NumLock
State
Hard Drive BBS
Priorities
Descriptions
Sets whether to enable or disable the keyboard’s NumLock state when the system starts up.
Options: On [default], Off.
Quiet Boot
Sets whether to display the POST (Power-on Self Tests) messages or the system manufacturer’s full screen logo during booting.
Leave it as
Disabled, which is the default, to display the normal POST message.
Boot Option Priorities Sets the system boot order
Sets the very 1st boot device among the available storage drives.
BBS means “BIOS Boot Specification”.
- 48 -
BIOS
4.6 Security
The Security menu sets up the administrator password. Once an administrator password is set up, this BIOS Setup utility is limited to access and will ask for the password each time any access is attempted.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Password Description
Set Adminstrator Password
If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.
If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
The password must be in the following range:
Minimum
Maximum
Administrator Password
HDD Security Configuration
HDD 0: MRSAJ5D032GC
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
The Security screen provides the following setting options:
Settings
Administrator
Password
HDD Security
Configuration
Descriptions
To set up an administrator password:
1. Select
Administrator Password.
2. A Create New Password dialog then pops up onscreen.
3. Enter your desired password that is no less than 3 characters and no more than 20 characters.
4. Hit [Enter] key to submit.
To view the HDD password configuration.
- 49 -
BIOS
4.7 Save & Exit
The Exit menu features a handful of commands to launch actions from the
BIOS Setup utility regarding saving changes, quitting the utility and recovering defaults.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Chipset Boot Security Save & Exit
Save Changes and Reset
Discard Changes and Exit
Restore Defaults
Boot Override
SATA PM: MRSAJ5D032GC225C00
Exit system setup after saving the changes.
→←
: Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F9: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
The Save & Exti screen provides the following setting options:
Settings
Save Changes and Exit
Discard
Changes and
Exit
Descriptions
Saves the changes and quits the BIOS Setup utility.
X
This is a command to launch an action from the BIOS Setup utility.
X
When prompted for confirmation, select
OK to save the changes and quit the BIOS Setup, or select Cancel to return to
BIOS Setup.
Discards the changes and quits the BIOS Setup utility.
This is a command to launch an action from the BIOS Setup utility.
X
When prompted for confirmation, select OK to quit BIOS Setup without saving the change(s), or select Cancel to return to the
BIOS setup.
- 50 -
Settings
Restore
Defaults
Boot Override
Descriptions
Loads the defaults to all settings.
This is a command to launch an action from the BIOS Setup utility.
When prompted for confirmation, select OK to load the defaults, or select Cancel to return to the BIOS setup.
Boot Override presents a list in context with the boot devices installed in the system. Select the device to boot up the system regardless of the currently configured boot priority.
This is a command to launch action from the BIOS Setup utility.
- 51 -
This page is intentionally left blank.
- 52 -
Appendix
Appendix
Optional Connections
Appendix Optional Connections
- 53 -
Appendix
A. Medical Arm
This medical computer can be mounted on a wall-mount, desktop-stand, or hospital arm for convenient operation. To mount it on a hospital arm, you need cross-headed screwdriver, and M6x40 size screws. Due to mechanical design, we don’t suggest you screw arm via VESA 75 holes (inner square), or you may risk the danger of damaging the computer in serious case. Please take advantage of VESA 100 holes.
1. Align the screw holes of arm’s VESA bracket with corresponding holes on the rear panel of the medical computer.
2. Secure provided M6x40 screws to the 4 aligned screw holes. Make sure you screw them firmly.
- 54 -
Appendix
B. Installing the Handset Holder
If you are going to use the phone handset (optional), install the holder to the computer as described below.
1. Place the computer face-down on a soft flat surface.
2. Remove the two screws securing the bezel on the right side and remove the bezel.
Please keep the bezel and screws in a safe place for reuse in the future.
3. To use the buzzer function (optional), connect the 2-pin wire connector to the buzzer connector of the computer. If your vendor doesn’t provide the related functionality, skip this step.
- 55 -
Appendix
4. Secure the holder to the computer with two screws included in the holder accessory pack.
C. Using the Handset
The computer can be connected to a handset to facilitate voice communication through video conference, Skype, and instant messaging. However, the handset audio is disabled by default and you have to enable the phone function in BIOS.
Note: The audio of this medical computer switches between the phone and the speaker/headset of the medical computer. For instance, when you lift the phone, the audio is switched to the phone so that phone conversation can be carried out. When the phone is hung off, the audio is automatically switched to the system.
To use the phone handset:
1. Install the handset holder to the computer as described in B. Installing the
on page
2. Enter BIOS > Advanced and enable the Phone Button Configuration option.
3. Using the RJ-11 phone cable included in the handset pack, connect one end to the handset and the other end to the PHONE jack on the rear of the computer.
- 56 -
Appendix
4. Launch the voice communication software. When you lift the handset, the audio automatically switches to the phone so that conversation can be carried out.
5. Hang off the phone when the conversation finishes. When the phone is hung off, the audio automatically switches back to the system.
You can also use the phone key on the front panel to toggle the phone mode on and off. The Phone LED light also change accordingly to reflect current phone status as described in the following table.
If you want to...
Use the handset as the audio device
Switch the audio to the system.
Adjust the handset volume
Then...
Phone LED
Status
Lift the handset to go off-hook, or press the phone button .
Replace the handset in the holder to go on-hook, or press the phone button .
Then the audio will automatically switch to the system.
Light green
Off
Press the or button on the front panel to decrease or increase the volume
-
- 57 -
Appendix
D. Using the Remote Controller and Nurse Call
Function
The computer can be optionally connected to a wired remote controller, enabling users to operate the medical computer or use navigation keys from a distance instead of touching the screens directly. The remote controller can also work as a handset for voice communication. Moreover, it comes with a nurse-call button on the rear to facilitate better communications between the patient, nurse and medical staff. This section will walk you through the function of the remote controller.
D.1 Overview
D.1.1 Specifications
Item
Dimensions (W x D x H)
Weight
Power Supply Voltage
Operating Temp.
Storage Temp.
Operating Humidity
Speaker
Microphone
Descriptions
180 x 54 x 29mm (7.09” x 2.13” x 1.14”)
108g
DC 5V provided by the computer
0 ~ 40°C (32 ~ 103°F)
-20 ~ 60°C (-4 ~ 140°F)
10~95% @ 40°C (non-condensing)
1 x internal 0.5W speaker
1 x digital microphone
D.1.2 Parts of the Remote Controller
Handset
Receiver
Nurse Call
Button
Keypad
Front
Handset
Transmitter
(Microphone)
- 58 -
Rear
Appendix
D.1.3 Keypad
Keypad Descriptions
Places a phone call
Ends a phone call
Enables audio
Mutes both system audio and handset audio
Functions as the Enter key on a generic keyboard to perform the following:
• To execute a command
• To confirm input
Up/down/right/left navigation keys. The functions depend if FN
(function) key is enabled.
FN Key Active Keys FN key inactive
Acts as a general navigation key to perform the following:
• Moves the caret in an input field.
• Navigates up/down/ right/left among the highlight items in certain applications.
Goes up one channel
Goes down one channel
Decreases volume
Increases volume
Numeric keypad for the following operation:
• Numeric characters input
• TV channel selection
• VoIP phone’s dial pad
- 59 -
Appendix
Keypad Descriptions
Turns on/off LCD
The
FN
(function) key, a modifier key to shift the function of some other keys.
Press the FN key to activate the function key. When active, the LED lights white.
Press the FN key again the disable the function key. When inactive, the LED is off.
Nurse-call button.
To use this function, the remote controller must be connected to the nurse call system of the hospital.
D.2 Connecting the Remote Controller
1. Connect the remote controller to the medical computer.
• Using the provided DB9-to-RJ45 cable, connect the DB9 plug to the
RC port of the medical computer and connect the RJ-45 plug to the
RJ-45 coupler.
• Connect the RJ-45 plug of the remote controller to the RJ-45 coupler.
RC port
DB9
Connector
DB9 to RJ-45 Cable
- 60 -
RJ-45 Coupler
RJ-45 Cable
Appendix
2. To use the Nurse Call Function, connect the computer’s nurse call RJ-11 jack to the telephone jack of the hospital’s nurse call system through a RJ-
11 phone cable.
Note: If you are not going to use the nurse call button function on the remote controller, then you can skip this connection.
RJ-11 Cable Nurse Call System
Phone Jack
Nurse Call
Phone Jack
The Nurse Call function uses independent power supplied by the hospital’s nurse call network. The pin assignment of the computer’s Nurse Call jack is as below:
1. NC Pin
2. Nurse Call GND
3. Nurse Call COMM
4. Nurse Call Power
1 2 3 4
- 61 -
Appendix
D.3 Programing Your Own Remote Controller Applications
For software developers to develop their own remote controller applications, please refer to the key mapping table and sample codes as a design reference.
D.3.1 Key Mapping Table
Num 4
Num 5
Num 6
Num 7
Num 8
Num 9
*
Num 0
Remote Controller Key Key Code
Phone On
F24
Phone Off
Audio Switch
F23
F22
Mute
Num 1
Num 2
Num 3
Mute
Keypad 1
Keypad 2
Keypad 3
Keypad 4
Keypad 5
Keypad 6
Keypad 7
Keypad 8
Keypad 9
Keypad 0
Keypad *
#
OK
LCD On/Off
Source
Up
Down
Left
Right
CH +
CH -
F16
Enter
F21
F20
Up
Down
Left
Right
F19
F18
Scan Code
118
107
72
80
75
55
103
28
108
77
106
105
71
72
73
82
81
75
76
77
110
109
N/A
79
80
- 62 -
Remote Controller Key Key Code
Vol +
Vol -
Nurse Call
Vol +
Vol -
F17
Scan Code
N/A
N/A
104
D.3.2 Linux Sample Code
Note: NumLock isn’t enabled upon Linux boot-up. You must make sure
NumLock is active for keypad numbers. Use “apt-get install numlockx” or
“yum install numlockx” to enable NumLock during application starting. See the sample code hereunder.
#include <sys/io.h>
#include <stdio.h>
#include <linux/input.h>
#define ARBOR_M1858_ECRAM_ADDR 0x0500
#define ARBOR_M1858_ECRAM_ADDR2 0x160A
#define ARBOR_M1858_ECRAM_ADDR3 0x0202
#define ARBOR_M1858_ECRAM_ADDR4 0x0461
//--------------------------------------------------------------------
-------------------------------------------------------
//----------------------------------- ARBOR GPIO ---------------------
--------------------------------------------------unsigned long Process_686C_Command_Write(unsigned long m_ECCMD, unsigned long m_ECDATA)
{
//-------------------------------------------------------------------
-------
int i,temp;
unsigned long m_OutBuf;
//-------------------------------------------------------------------
-------
m_OutBuf=inb_p(0x6C);
if ( ( m_OutBuf&0x00000003) > 0 )
{
temp=inb_p(0x68);
return 0xFFFFFFFF;
}
outb_p(m_ECCMD, 0x6C);
for ( i=0; i<=4000; i++ )
- 63 -
Appendix
Appendix
{
m_OutBuf=inb_p(0x6C);
if ( ( m_OutBuf&0x00000002) == 0 ) break;
}
if ( i < 3999 )
{
outb_p(m_ECDATA, 0x68);
for ( i=0; i<=4000; i++ )
{
m_OutBuf=inb_p(0x6C);
if ( ( m_OutBuf&0x00000002) == 0 )
{ return 0x00000000; }
}
}
if ( i > 3999 ) m_OutBuf=inb_p(0x68);
return 0xFFFFFFFF;
}
//--------------------------------------------------------------------
------unsigned long Process_686C_Command_Read(unsigned long m_ECCMD )
{ int i,temp;
unsigned long m_OutBuf,m_InBuf;
m_OutBuf=inb_p(0x6C); if ( ( m_OutBuf&0x00000003) > 0 )
{
temp=inb_p(0x68);
return 0xFFFFFFFF;
}
m_InBuf = m_ECCMD;
outb_p(m_InBuf, 0x6C);
for ( i=0; i<=3500; i++ )
{
m_OutBuf=inb_p(0x6C);
if ( ( m_OutBuf&0x00000001) > 0 )
{
temp=inb_p(0x68);
temp= (temp & 0x000000FF ) ;
return temp;
break;
}
}
if ( i > 3499 )
{
temp=inb_p(0x68);
return 0xFFFFFFFF;
}
}
- 64 -
Appendix
//--------------------------------------------------------------------
--------
unsigned long ECU_Read_686C_RAM_BYTE( unsigned long ECUMemAddr )
{
unsigned long uDATA1,uDATA2,ECRamAddrH,ECRamAddrL;
ECRamAddrL=ECUMemAddr%256; ECRamAddrH=ECUMemAddr/256;
//
uDATA1=Process_686C_Command_Write(0x000000A3, ECRamAddrH );
if ( uDATA1==0xFFFFFFFF ) { return 0xFFFFFFFF; }
//
uDATA1=Process_686C_Command_Write(0x000000A2, ECRamAddrL );
if ( uDATA1==0xFFFFFFFF ) { return 0xFFFFFFFF; }
//
uDATA1=Process_686C_Command_Read( 0x000000A4 );
if ( uDATA1 > 0x000000FF ) { return 0xFFFFFFFF; }
uDATA2=Process_686C_Command_Read( 0x000000A4 );
if ( uDATA2 > 0x000000FF ) { return 0xFFFFFFFF; }
if (uDATA1==uDATA2) return uDATA1;
else return 0xFFFFFFFF;
}
//--------------------------------------------------------------------
--------
unsigned long ECU_Write_686C_RAM_BYTE( unsigned long
ECUMemAddr,unsigned long ECUMemData )
{
unsigned long uDATA, RD_DATA, ECRamAddrH, ECRamAddrL;
ECRamAddrL=ECUMemAddr%256; ECRamAddrH=ECUMemAddr/256;
//
uDATA=Process_686C_Command_Write(0x000000A3, ECRamAddrH );
if ( uDATA==0xFFFFFFFF ) { return 0xFFFFFFFF;}
//
uDATA=Process_686C_Command_Write(0x000000A2, ECRamAddrL );
if ( uDATA==0xFFFFFFFF ) { return 0xFFFFFFFF;}
//
uDATA=Process_686C_Command_Write(0x000000A5, ECUMemData );
if ( uDATA==0xFFFFFFFF ) { return 0xFFFFFFFF;}
//
return 0x00000000;
} main()
{ unsigned long ldata; unsigned long temp;
- 65 -
Appendix int res=0;
FILE * keyfd = NULL; struct input_event ie; int LCDStatus = 1; system(“/usr/bin/numlockx on”); //enable NumLock res=iopl(3); setuid(500); keyfd = fopen(“/dev/input/event16”, “r”); //application must choose correct event for remote control if(keyfd != NULL)
{ while(1)
{
{ fread((void *)&ie, sizeof(ie), 1, keyfd); if (ferror(keyfd))
}
perror(“fread”);
exit(1); if(ie.code == 1 && ie.value == 1) //ESC
{
//exit application printf(“Exit\n”); break;
} if(ie.code == 194 && ie.value == 1) //F24
{
} printf(“Phone On\n”); if(ie.code == 193 && ie.value == 1) //F23
{ printf(“Phone Off\n”);
} if(ie.code == 192 && ie.value == 1) //F22
{ printf(“Audio switch\n”);
} if(ie.code == 191 && ie.value == 1) //F21
{ printf(“LCD On/off\n”);
if( LCDStatus == 1)
- 66 -
Appendix
BYTE(0x1604); if(temp != 0xFFFFFFFF)
{
BYTE(0x1604,temp);
{ if(temp == 0xFFFFFFFF) temp = ECU_Read_686C_RAM_
//backlight off temp &= 0xBF;
ECU_Write_686C_RAM_
} temp = ECU_Read_686C_RAM_
BYTE(0x1605);
BYTE(0x1605); if(temp == 0xFFFFFFFF) temp = ECU_Read_686C_RAM_ if(temp != 0xFFFFFFFF)
{
// TOUCH_SHDN Switch off temp &= 0xDF;
ECU_Write_686C_RAM_
BYTE(0x1605,temp);
}
BYTE(0x1604);
LCDStatus = 0;
}
else if(LCDStatus == 0)
{
temp = ECU_Read_686C_RAM_BYTE(0x1604); if(temp == 0xFFFFFFFF) temp = ECU_Read_686C_RAM_ if(temp != 0xFFFFFFFF)
{
//backlight on temp |= 0x40;
ECU_Write_686C_RAM_
BYTE(0x1604,temp);
}
LCDStatus = 1; temp = ECU_Read_686C_RAM_
BYTE(0x1605);
BYTE(0x1605); if(temp == 0xFFFFFFFF) temp = ECU_Read_686C_RAM_ if(temp != 0xFFFFFFFF)
{
// TOUCH_SHDN Switch off temp &= 0xDF;
- 67 -
Appendix
BYTE(0x1605,temp);
}
}
ECU_Write_686C_RAM_
} if(ie.code == 190 && ie.value == 1) //F20
{ printf(“Video Switch\n”);
} if(ie.code == 189 && ie.value == 1) //F19
{ printf(“CH +\n”);
} if(ie.code == 188 && ie.value == 1) //F18
{ printf(“CH -\n”);
} if(ie.code == 187 && ie.value == 1) //F17
{ printf(“Nurse Call\n”);
} if(ie.code == 186 && ie.value == 1) //F16
{ printf(“#\n”);
}
}
}
if(keyfd != NULL)
fclose(keyfd);
}
- 68 -
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project