null User manual

null  User manual
WEB EDITION
OWNER'S MANUAL
DEAR VOLVO OWNER
THANK YOU FOR CHOOSING VOLVO
We hope you will enjoy many years of driving
pleasure in your Volvo. The car has been
designed for the safety and comfort of you and
your passengers. Volvo is one of the safest cars in
the world. Your Volvo has also been designed to
satisfy all current safety and environmental
requirements.
In order to increase your enjoyment of the car, we
recommend that you familiarise yourself with the
equipment, instructions and maintenance information contained in this owner's manual.
Table of contents
00 Introduction
01 Safety
Important information................................. 8
Volvo and the environment....................... 12
Seatbelts...................................................
Symbols, airbags......................................
Airbags......................................................
Activating/deactivating the airbag*...........
Side airbags (SIPS bags)..........................
Inflatable Curtain (IC)................................
WHIPS.......................................................
Roll-over protection - ROPS.....................
When the systems deploy.........................
Child safety...............................................
02 Instruments and controls
18
21
22
24
26
28
29
31
32
34
Overview, left-hand drive cars..................
Overview, right-hand drive cars................
Driver's door control panel.......................
Combined instrument panel......................
Indicator and warning symbols.................
Information display...................................
Switches in the centre console.................
Lighting panel...........................................
Left-hand stalk switch...............................
Trip computer*..........................................
Right-hand stalk switch............................
Cruise control*..........................................
Parking brake, electrical socket, etc.........
Power windows.........................................
Windows, rearview and door mirrors........
Power sunroof*.........................................
00 01 02
2
* Option/accessory, for more information, see Introduction.
50
52
54
55
57
60
61
64
67
68
70
73
75
77
79
84
Table of contents
03 Climate control
04 Interior
General information on climate control..... 88
Electronic Climate Control, ECC............... 91
Fuel-driven parking heater*....................... 94
Front seats..............................................
Front seats - Executive ..........................
Interior lighting........................................
Storage spaces in the passenger compartment..................................................
Storage spaces in the passenger compartment - Executive ..............................
Rear seat.................................................
Loading...................................................
Cargo area..............................................
05 Locks and alarm
100
103
104
Remote control key - key with remote
control.....................................................
Locking and unlocking............................
Child safety locks....................................
Alarm*.....................................................
03 04 05
106
124
126
130
131
111
112
114
115
* Option/accessory, for more information, see Introduction.
3
Table of contents
06 Starting and driving
General....................................................
Refuelling................................................
Starting the engine..................................
Automatic gearbox..................................
All-wheel drive*.......................................
Brake system..........................................
Stability and traction control system*.....
Park assist syst*......................................
Blind Spot Information System - BLIS*...
Towing and recovery..............................
Jump starting..........................................
Driving with a trailer................................
Towing equipment*.................................
Detachable towbar*................................
Adjusting headlamp pattern....................
07 Wheels and tyres
136
139
145
147
150
151
153
155
157
161
163
165
167
169
173
General....................................................
Tyre pressure..........................................
Warning triangle* and spare wheel *.......
Changing wheels....................................
Emergency puncture repair*...................
08 Car care
180
183
184
187
190
Cleaning.................................................. 198
Touching up paintwork........................... 202
Rustproofing........................................... 204
06 07 08
4
* Option/accessory, for more information, see Introduction.
Table of contents
09 Maintenance and service
Volvo service...........................................
Self-maintenance....................................
Bonnet and engine compartment...........
Oils and fluids.........................................
Wiper blades...........................................
Battery.....................................................
Replacing bulbs......................................
Fuses......................................................
10 Infotainment system
208
209
211
213
218
220
223
230
General....................................................
Control panels, audio..............................
Audio system functions..........................
Radio functions.......................................
CD functions...........................................
Menu structure – audio system..............
Phone functions*.....................................
Menu structure – phone..........................
Bluetooth handsfree*..............................
RSE - Rear Seat Entertainment system Dual Screen* ..........................................
11 Specifications
244
245
248
253
259
262
263
270
274
Type designation.....................................
Dimensions and weights.........................
Engine specifications..............................
Engine oil................................................
Fluids and lubricants...............................
Fuel.........................................................
Wheel and tyres, dimensions and pressure ........................................................
Catalytic converter..................................
Electrical system.....................................
Type approval.........................................
Symbols in the display............................
09 10 11
280
286
288
291
292
294
296
297
298
299
301
302
* Option/accessory, for more information, see Introduction.
5
Table of contents
12 Alphabetical Index
Alphabetical Index.................................. 304
12
6
Table of contents
7
Introduction
Important information
Reading the owner's manual
Introduction
A good way of getting to know your new car
is to read the owner's manual, ideally before
your first journey. This will give you the
opportunity to familiarise yourself with new
functions, to see how best to handle the car
in different situations, and to make the best
use of all the car's features. Please pay attention to the safety instructions contained in the
manual.
The specifications, design features and illustrations in the owner's manual are not binding. We reserve the right to make modifications without prior notice.
©
Volvo Car Corporation
Option
All types of option/accessory are marked with
an asterisk*.
In addition to standard equipment, this manual also describes options (factory fitted
equipment) and certain accessories (retrofitted extra equipment).
The equipment described in the owner's
manual is not available in all cars - they have
different equipment depending on adaptations for the needs of different markets and
national or local laws and regulations.
8
In the event of uncertainty over what is standard or an option/accessory, contact a Volvo
dealer.
Special texts
WARNING
Warning texts appear if there is a risk of
injury.
IMPORTANT
"Important" texts appear if there is a risk of
damage.
the text being slightly larger and printed in
grey. Examples of this are in menu texts and
message texts on the information display
(e.g. DOORS OPEN).
Decals
The car contains different types of decal
which are designed to convey important
information in a simple and clear manner. The
decals in the car have the following descending degree of importance for the warning/
information.
Warning for personal injury
NOTE
NOTE texts give advice or tips that facilitate the use of e.g. features and functions.
Footnote
There is footnote information in the owner's
manual that is located at the bottom of the
page. This information is an addition to the
text that it refers to via a number. If the footnote refers to text in a table then letters are
used instead of numbers for referral.
Message texts
There are displays in the car that show text
messages. These text messages are highlighted in the owner's manual by means of
* Option/accessory, for more information, see Introduction.
G031590
Black ISO symbols on yellow warning field,
white text/image on black message field.
Used to indicate the presence of danger
Introduction
Important information
which, if the warning is ignored, may result in
serious personal injury or fatality.
Information
Procedure lists
Procedures where action must be taken in a
certain sequence are numbered in the
owner's manual.
Risk of property damage
When there is a series of illustrations for
step-by-step instructions each step is
numbered in the same way as the corresponding illustration.
G031592
G031593
There are numbered lists with letters
adjacent to the series of illustrations
where the order of the instructions is not
significant.
White ISO symbols and white text/image on
black or blue warning field and message field.
Used to indicate the presence of danger
which, if the warning is ignored, may result in
damage to property.
White ISO symbols and white text/image on
black message field.
NOTE
It is not intended that the decals illustrated
in the owner's manual should be exact
replicas of those in the car. They are
included to show their approximate
appearance and location in the car. The
information that applies to your particular
car is available on the respective decals
for your car.
Arrows appear numbered and unnumbered and are used to illustrate a movement.
Arrows with letters are used to clarify a
movement when the reciprocal order is of
no relevance.
If there is no series of illustrations for step-bystep instructions then the different steps are
numbered with normal numbers.
Position lists
Red circles containing a number are used
in overview images where different components are pointed out. The number
recurs in the position list featured in connection with the illustration that describes
the item.
9
Introduction
Important information
Bulleted lists
A bulleted list is used when there is a list of
points in the owner's manual.
Example:
•
•
Coolant
Engine oil
Images
The manual's images are sometimes schematic and may deviate from the car's appearance depending on equipment level and market.
To be continued
}} This symbol is located furthest down to
the right when a section continues on the following page.
Recording data
Your vehicle contains a number of computers
whose function is to continuously check and
monitor the vehicle's operation and functionality. Some of the computers can record
information during normal driving if they
detect an error. In addition, information is
recorded in the event of a collision or incident. Parts of the recorded information are
required so that technicians can diagnose
and rectify faults in the vehicle during servicing and maintenance and so that Volvo can
10
fulfil legal requirements and other regulations.
In addition to this, the information is used for
research purposes by Volvo in order to continually develop quality and safety, as the
information can contribute to a better understanding of the factors that cause accidents
and injuries. The information includes details
of the status and functionality of various systems and modules in the vehicle with regard
to engine, throttle, steering and brake systems, amongst other things. This information
may include details regarding the way the
driver drives the vehicle, such as vehicle
speed, brake and accelerator pedal use,
steering wheel movement and whether or not
the driver and passengers have used their
seatbelts. For the reasons given this information may be stored in the vehicle's computers
for a certain length of time, but also as a
result of a collision or incident. This information may be stored by Volvo as long as it can
help to further develop and further enhance
safety and quality and as long as there are
legal requirements and other regulations that
Volvo needs to consider.
Volvo will not contribute to the above-described information being disclosed to third parties without the vehicle owner's consent.
However, due to national legislation and regulations Volvo may be required to disclose
such information to authorities such as police
authorities, or others who may assert a legal
right to have access to it.
To be able to read and interpret the information recorded by the computers in the vehicle
requires special technical equipment that
Volvo, and workshops that have entered into
agreements with Volvo, have access to. Volvo
is responsible that the information, which is
transferred to Volvo during servicing and
maintenance, is stored and handled in a
secure manner and that the handling complies with applicable legal requirements. For
further information - contact a Volvo dealer.
Accessories and extra equipment
The incorrect connection and installation of
accessories can negatively affect the car's
electrical system. Certain accessories only
function when their associated software is
installed in the car's computer system. We
therefore recommend that you always contact an authorised Volvo workshop before
installing accessories which are connected to
or affect the electrical system.
Introduction
Important information
Change of ownership for cars with
Volvo On Call *
Volvo On Call is a supplemental service that
consists of safety, security and comfort services. If the car has Volvo On Call and there is
a change of owner, it is very important that
these services are discontinued so that the
former owner cannot access the services in
the car. Contact an authorised Volvo dealer in
the event of a change of ownership.
Information on the Internet
At www.volvocars.com there is further information concerning your car.
A QR code reader is required to read the QR
code, which is available as a supplemental
program for several mobile phones. The QR
code reader can be downloaded from App
Store or Google Play.
QR code
* Option/accessory, for more information, see Introduction.
11
Introduction
Volvo and the environment
G000000
Volvo Cars' environmental philosophy
Environmental care is one of Volvo Car Corporation's core values which influence all
operations. We also believe that our customers share our consideration for the environment.
Your Volvo complies with strict international
environmental standards and is also manufactured in one of the cleanest and most
resource-efficient plants in the world. Volvo
Car Corporation has global ISO certification,
which includes the environmental standard
ISO 14001 covering all factories and several
of our other units. We also set requirements
12
for our partners so that they work systematically with environmental issues.
Fuel consumption
Volvo cars have competitive fuel consumption in each of their respective classes. Lower
fuel consumption generally results in lower
emission of the greenhouse gas, carbon dioxide.
It is possible for the driver to influence fuel
consumption. For more information read
under the heading, Reducing environmental
impact.
Efficient emission control
Your Volvo is manufactured following the
concept "Clean inside and out" – a concept
that encompasses a clean interior environment as well as highly efficient emission control. In many cases the exhaust emissions are
well below the applicable standards.
Clean air in the passenger
compartment
A passenger compartment filter prevents dust
and pollen from entering the passenger compartment via the air intake.
Introduction
Volvo and the environment
A sophisticated air quality system, IAQS*
(Interior Air Quality System) ensures that the
incoming air is cleaner than the air in the traffic outside.
The system consists of an electronic sensor
and a carbon filter. The incoming air is monitored continuously and if there is an increase
in the level of certain unhealthy gases such as
carbon monoxide then the air intake is
closed. Such a situation may arise in heavy
traffic, queues and tunnels for example.
The entry of nitrous oxides, ground-level
ozone and hydrocarbons is prevented by the
carbon filter.
charges into the environment. Our workshop
staff have the knowledge and the tools
required to guarantee good environmental
care.
Reducing environmental impact
You can easily help reduce environmental
impact - here are a few tips:
•
•
•
Drive economically - think ahead.
•
If the car is equipped with an engine
block heater*, use it before starting from
cold - it improves starting capacity and
reduces wear in cold weather and the
engine reaches normal operating temperature more quickly, which lowers consumption and reduces emissions.
Interior
The interior of a Volvo is designed to be pleasant and comfortable, even for people with
contact allergies and for asthma sufferers.
Extreme attention has been given to choosing
environmentally-compatible materials.
Volvo workshops and the environment
Regular maintenance creates the conditions
for a long service life and low fuel consumption for your car. In this way you contribute to
a cleaner environment. When Volvo's workshops are entrusted with the service and
maintenance of your car it becomes part of
our system. We make clear demands regarding the way in which our workshops are
designed in order to prevent spills and dis-
Avoid letting the engine idle - switch off
the engine when stationary for longer
periods. Pay attention to local regulations.
Perform service and maintenance in
accordance with the instructions in the
owner's manual - follow the Service and
Warranty Booklet's recommended intervals.
•
High speed increases consumption considerably due to increased wind resistance - a doubling of speed increases
wind resistance 4 times.
•
Always dispose of environmentally hazardous waste, such as batteries and oils, in
an environmentally safe manner. Consult
a workshop in the event of uncertainty
about how this type of waste should be
discarded - an authorised Volvo workshop is recommended.
Following this advice can save money, the
planet's resources are saved, and the car's
durability is extended. For more information
and further advice, see the pages 136 and
296.
Recycling
As a part of Volvo's environmental work, it is
important that the car is recycled in an environmentally sound manner. Almost all of the
car can be recycled. The last owner of the car
is therefore requested to contact a dealer for
referral to a certified/approved recycling
facility.
The owner's manual and the
environment
The Forest Stewardship Council® symbol
shows that the paper pulp in this publication
comes from FSC® certified forests or other
controlled sources.
* Option/accessory, for more information, see Introduction.
13
Introduction
Volvo and the environment
14
Introduction
15
Seatbelts.................................................................................................
Symbols, airbags....................................................................................
Airbags....................................................................................................
Activating/deactivating the airbag*.........................................................
Side airbags (SIPS bags)........................................................................
Inflatable Curtain (IC)..............................................................................
WHIPS.....................................................................................................
Roll-over protection - ROPS...................................................................
When the systems deploy.......................................................................
Child safety.............................................................................................
16
* Option/accessory, for more information, see Introduction.
18
21
22
24
26
28
29
31
32
34
SAFETY
01 Safety
Seatbelts
01
Always use a seatbelt
Releasing the seatbelt
–
Press the red lock button and then let the
seatbelt retract. If the seatbelt does not
retract fully, feed the seatbelt in by hand
so that it does not hang loose.
The seatbelt locks and cannot be
withdrawn
G020104
•
•
•
Tensioning the hip strap. The belt must be positioned low down.
Heavy braking can have serious consequences if the seatbelts are not used. Ensure that
all passengers use their seatbelts. It is important that the seatbelt lies against the body so
it can provide maximum protection. Do not
lean the backrest too far back. The seatbelt is
designed to protect in a normal seating position.
Putting on a seatbelt:
–
18
Pull the seatbelt out slowly and secure it
by pressing the buckle into the lock. A
loud "click" indicates that the seatbelt
has locked.
if it is pulled out too quickly
during braking and acceleration
if the car leans heavily.
Keep in mind the following
•
do not use clips or anything else that can
prevent the seatbelt from fitting properly
•
ensure that the seatbelt is not twisted or
caught on anything
•
the hip strap must be positioned low
down (not over the abdomen)
•
tension the hip strap over the lap by pulling the diagonal shoulder belt as illustrated.
WARNING
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
WARNING
Each seatbelt is designed for only one person.
WARNING
Never modify or repair the seatbelts yourself. Volvo recommends that you contact
an authorised Volvo workshop. If a seatbelt has been subjected to a major load,
such as in conjunction with a collision, the
entire seatbelt must be replaced. Some of
the protective characteristics of the seatbelt may have been lost, even if it appears
to be undamaged. In addition, replace the
seatbelt if the belt is worn or damaged.
The new seatbelt must be type-approved
and intended for installation in the same
position as the replaced seatbelt.
01 Safety
Seatbelts
Seatbelts and pregnancy
wheel such that they can easily maintain control of the vehicle as they drive (which means
that they must be able to easily operate the
foot pedals and steering wheel). Within this
context, they should strive to position the
seat with as large a distance as possible
between the abdomen and the steering
wheel.
01
car is started). The visual reminder is located
in the roof console and in the combined
instrument panel.
NOTE
The seatbelt reminder is intended for an
adult sitting in the front seat. If a belt-fitted
child seat is fitted in the front seat, the
seatbelt reminder does not switch on.
Seatbelt reminder
Certain markets
G020105
An acoustic signal and indicator lamp remind
the driver if not wearing a seatbelt to use one.
At low speed, the audio reminder will sound
for the first 6 seconds.
The seatbelt should always be worn during
pregnancy. But it is crucial that it be worn in
the correct way. The diagonal section should
wrap over the shoulder then be routed
between the breasts and to the side of the
abdomen.
As the pregnancy progresses, pregnant drivers should adjust their seats and steering
G027049
The lap section should lay flat over the thighs
and as low as possible under the abdomen. –
It must never be allowed to ride upward.
Remove the slack from the seatbelt and
ensure that it fits as close to the body as possible. In addition, check that there are no
twists in the seatbelt.
Seatbelt tensioner
All the seatbelts are equipped with belt tensioners. A mechanism in the seatbelt tensioner tightens the seatbelt around the body
in the event of a sufficiently violent collision.
The seatbelt then provides more effective
restraint for the occupants.
An acoustic signal and indicator lamp remind
the driver and front seat passenger to use a
seatbelt if either of them is not wearing one.
The audible reminder is speed dependent (at
low speeds), and time dependent (when the
}}
19
01 Safety
01
Seatbelts
WARNING
Never insert the tongue of the passenger's
seatbelt into the buckle on the driver's
side. Always insert the tongue of the seatbelt into the buckle on the correct side. Do
not make any damages on seatbelts nor
insert any foreign objects into a buckle.
The seatbelts and buckles would then
possibly not function as intended in the
event of a collision. There is a risk of
serous injury.
20
01 Safety
Symbols, airbags
Warning symbol on the combined
instrument panel
01
As well as the warning symbol, a
message may appear on the display in appropriate cases. If the
warning symbol malfunctions, the
warning triangle illuminates and
the message SRS AIRBAG
SERVICE URGENT appears in
the display. Volvo recommends
that you contact an authorised
Volvo workshop immediately.
G027284
WARNING
The warning symbol in the combined instrument panel illuminates when the remote control key is turned to key position I, II or III.
The symbol goes out after approx. 6 seconds
provided the airbag system is fault-free.
If the warning symbol for the airbag system remains illuminated or illuminates
while driving, it means that the airbag system does not have full functionality. The
symbol may indicate a fault in the airbag
system, the seatbelt tensioner system,
SIPS or the IC system. Volvo recommends
that you contact an authorised Volvo
workshop immediately.
21
01 Safety
Airbags
01
Airbag system1
NOTE
Airbag system, left-hand drive car.
The system consists of airbags and sensors.
A sufficiently violent collision trips the sensors
and the airbag(s) are inflated with hot gas. To
cushion the impact, the airbag deflates when
compressed. When this occurs, smoke
escapes into the car. This is completely normal. The entire process, including inflation
and deflation of the airbag, takes place within
tenths of a second.
G020110
G020111
The detectors react differently depending
on the nature of the collision and whether
or not the seatbelts are fastened. Applies
to all seatbelt positions apart from centre
seat rear.
It is therefore possible that only one (or
none) of the airbags may inflate in a collision. The detectors sense the force of the
collision on the vehicle and the action is
adapted accordingly so that one or more
airbags are deployed.
Airbag system, right-hand drive car
WARNING
Volvo recommends that you contact an
authorised Volvo workshop for repair.
Defective work in the airbag system could
cause malfunction and result in serious
personal injury.
Location of the passenger airbag in left-hand
drive and right-hand drive cars.
1
22
Also called the SRS system.
01 Safety
Airbags
WARNING
Do not put objects in front of or above the
instrument panel where the passenger airbag is located.
Airbag on the driver's side
The car has an airbag to supplement the protection afforded by the seatbelt on the driver's side. It is folded up into the centre of the
steering wheel. The steering wheel is marked
SRS AIRBAG.
WARNING
The seatbelts and airbags interact. If a
seatbelt is not used or is used incorrectly,
this may diminish the protection provided
by the airbag in the event of a collision.
01
WARNING
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright as
possible with their feet on the floor and
backs against the backrest. Seatbelts
must be secured.
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag is activated.2
Never allow anybody to stand or sit in front
of the front passenger seat. No one shorter
than 140 cm should ever sit in the front
passenger seat if the airbag is activated.
Failure to follow the advice given above
can endanger life.
Passenger airbag
The car has an airbag to supplement the protection afforded by the seatbelt on the passenger side. It is folded up into a compartment above the glovebox. The cover panel is
marked SRS AIRBAG.
2
For information on activated/deactivated airbag, see page 24.
23
01 Safety
01
Activating/deactivating the airbag*
Key switch off - PACOS*
General information
The airbag for the front passenger seat can
be deactivated if the car is equipped with a
switch, PACOS (Passenger Airbag Cut Off
Switch). For information on how to activate/
deactivate, see under the heading Activating/
deactivating.
Key switch off/switch
The switch for the passenger airbag (PACOS)
is located on the passenger end of the instrument panel and is accessible when the passenger door is open, (see under the heading
below, Activating/deactivating).
Check that the switch is in the required position. The remote control key's key blade
should be used to change position.
For information on the key blade, see
page 124.
WARNING
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag is activated. Failure to follow this
advice could endanger the life of the child.
WARNING
If the car is equipped with a front passenger airbag, but does not have PACOS,
then the airbag will always be activated.
WARNING
Do not allow anyone to sit in the front passenger seat if the text message in the rearview mirror indicates that the airbag is
deactivated, and if the warning symbol for
the airbag system is also displayed on the
combined instrument panel. This indicates
that there has been a severe malfunction.
Visit a workshop as soon as possible.
Volvo recommends that you contact an
authorised Volvo workshop
Failure to follow the advice given above
can endanger life.
24
Activating/deactivating
* Option/accessory, for more information, see Introduction.
Location of airbag label plus switch.
The airbag is activated. With the switch in
this position, persons taller than 140 cm
can sit in the front passenger seat, but
never children in a child seat or on a
booster cushion.
The airbag is deactivated. With the switch
in this position, children in a child seat or
on a booster cushion can sit in the front
passenger seat, but never persons taller
than 140 cm.
01 Safety
Activating/deactivating the airbag*
WARNING
01
Message
Activated airbag (passenger seat):
Never place a child in a child seat or on a
booster cushion on the front passenger
seat when the airbag is activated. This
applies to everyone shorter than 140 cm.
Deactivated airbag (passenger seat):
No one taller than 140 cm should ever sit
in the front passenger seat when the airbag is deactivated.
G027050
Failure to follow the advice given above
can endanger life.
Indicator showing that the passenger airbag is
deactivated.
A text message in the rearview mirror indicates that the airbag for the front passenger
seat is deactivated (see preceding illustration).
* Option/accessory, for more information, see Introduction.
25
01 Safety
01
Side airbags (SIPS bags)
Side airbag
G020118
Location
Side airbag locations.
In a side impact collision a large proportion of
the collision force is transferred by the SIPS
(Side Impact Protection System) to beams,
pillars, the floor, the roof and other structural
parts of the body. The side airbags at the
driver's and front passenger seats protect the
chest area and are an important part of the
system. The side airbags are located in the
front seat backrests.
Front passenger seat, left-hand drive
Driver's seat, left-hand drive
The SIPS bag system consists of side airbags
and sensors. A sufficiently violent collision
trips the sensors and the side airbags are
inflated. The airbag inflates between the
occupant and the door panel and thereby
cushions the initial impact. The airbag
deflates when compressed by the collision.
The side airbag is normally only deployed on
the side of the collision.
Child seats and side airbags
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the side airbag.
26
01 Safety
Side airbags (SIPS bags)
01
WARNING
•
Volvo recommends that repairs are
only carried out by an authorised Volvo
workshop. Defective work in the SIPSbag system could cause malfunction
and result in serious personal injury.
•
Do not put objects in the area between
the outside of the seat and the door
panel, since this area is required by
the side airbag.
•
Volvo recommends the use only of car
seat covers approved by Volvo. Other
seat covers may impede the operation
of the side airbags.
•
Side airbags are a supplement the
seatbelts. Always use a seatbelt.
27
01 Safety
01
Inflatable Curtain (IC)
Properties
WARNING
Never hang or attach heavy items onto the
handles in the roof. The hook is only
designed for light clothing (not for solid
objects such as umbrellas for example).
G027047
Do not screw or install anything onto the
car's headlining, door pillars or side panels. This could compromise the intended
protection. Volvo recommends that you
only ever use Volvo genuine parts that are
approved for placement in these areas.
The inflatable curtain IC (Inflatable Curtain) is
a part of SIPS and the airbags. It is fitted in
the headlining along both sides of the roof
and protects the car's occupants sitting in the
outer seats. A sufficiently violent collision
trips the sensors and the inflatable curtain is
inflated. The inflatable curtain helps to prevent the driver and passengers from striking
their heads on the inside of the car during a
collision.
28
WARNING
Do not load the car higher than 50 mm
under the top edge of the side windows.
Otherwise, the intended protection of the
inflatable curtain, which is concealed in the
headlining, may be compromised.
WARNING
The inflatable curtain is a supplement to
the seatbelts.
Always use a seatbelt.
01 Safety
WHIPS
01
G020347
Protection against whiplash injury – WHIPS
The whiplash protection system (WHIPS) consists of energy absorbing backrests and specially designed head restraints in the front
seats. The system is actuated by a rear-end
collision, where the angle and speed of the
collision, and the nature of the colliding vehicle all have an influence.
WARNING
The WHIPS system is a supplement to the
seatbelts. Always use a seatbelt.
Properties of the seat
When the WHIPS system is deployed, the
front seat backrests are lowered backward to
alter the seating position of the driver and
front seat passenger. This reduces the risk of
whiplash injury.
WARNING
Never modify or repair the seat or WHIPS
system yourself. Volvo recommends that
you contact an authorised Volvo workshop.
WHIPS system and child seats/booster
cushions
The protection provided by the car to children
seated in a child seat or on a booster cushion
is not diminished by the WHIPS system.
Correct seating position
For the best possible protection, the driver
and front seat passenger should sit in the
centre of the seat with as little space as possible between the head and the head
restraint.
}}
29
01 Safety
01
WHIPS
Do not obstruct the WHIPS system
WARNING
If a seat has been subjected to extreme
forces, such as due to a rear-end collision,
the WHIPS system must be checked.
Volvo recommends that you contact an
authorised Volvo workshop.
Do not leave any objects on the floor behind the
driver's seat/passenger seat that may prevent the
WHIPS system from functioning.
WARNING
Do not squeeze rigid objects between the
rear seat cushion and the front seat backrest. Make sure you do not to obstruct the
function of the WHIPS system.
30
G020126
G020125
Part of the WHIPS system's protective
capacity may have been lost even if the
seats appear to be undamaged.
Do not place objects in the rear seat that may
prevent the WHIPS system from functioning.
WARNING
If a rear seat backrest is folded down, the
corresponding front seat must be moved
forward so that it does not touch the
folded backrest.
Volvo recommends that you contact an
authorised Volvo workshop to have the
system checked even after a minor rearend collision.
01 Safety
Roll-over protection - ROPS
Function
Volvo's Roll-Over Protection System (ROPS)
has been designed to reduce the risk of the
car overturning and to provide the best possible protection in the event of such an accident.
01
WARNING
Under normal driving conditions, the RSC
system improves the car's road safety, but
this must not be seen as an opportunity to
increase speed. Always follow the normal
precautions for safe driving.
The system consists of:
•
A stabiliser system, RSC (Roll Stability
Control) that minimises the risk of overturning during sudden evasive manoeuvres or the like or if the car skids.
•
Increased protection for the driver and
passengers through a reinforced body,
inflatable curtains and seatbelt tensioners
in all seats. See also pages 19 and 28.
The RSC system uses a gyro sensor which
registers changes in the car's lateral inclination angle. This information is used to calculate the risk of the car overturning. If a risk is
detected, the DSTC system is engaged,
engine speed is reduced and one or more
wheels are braked until the car returns to a
stable position.
For more information on the DSTC system,
see page 153.
31
01 Safety
When the systems deploy
01
System
Triggered
Seatbelt tensionerA
In a frontal collision and/or overturning.
Airbags
In a frontal collisionB
(Steering wheel and passenger airbag)
Side airbags SIPS
In a side-impact accidentB
Inflatable Curtain IC
In a side-impact accident and/or overturningB.
Whiplash protection WHIPS
In a rear-end collision.
RSC
During sudden evasive manoeuvres or the like or if the car skids.
A
B
Seatbelt tensioner is not available in centre seat rear.
The bodywork of the car could be greatly deformed in a collision without airbag deployment. A number of factors such as the rigidity and weight of the object hit, the speed of the car, the angle of
the collision etc. affects how the different safety systems of the car are activated.
If the airbags have deployed, the following is
recommended:
32
•
Recovering the car. Volvo recommends
that you have it conveyed to an authorised Volvo workshop for repair. Do not
drive with deployed airbags.
•
Volvo recommends that you engage an
authorised Volvo workshop to handle the
replacement of components in the car's
safety systems.
•
Always contact a doctor.
NOTE
The SIPS, IC, airbag and belt tensioner
systems are deployed only once during a
collision.
WARNING
The airbag system's control module is
located in the centre console. If the centre
console is drenched with water or other
liquid, disconnect the battery cables. Do
not attempt to start the car since the airbags may deploy. Recovering the car.
Volvo recommends that you have it conveyed to an authorised Volvo workshop.
01 Safety
When the systems deploy
01
WARNING
Never drive with deployed airbags. They
can make steering difficult. Other safety
systems may also be damaged. The
smoke and dust created when the airbags
are deployed can cause skin and eye irritation/injury after intensive exposure. In case
of irritation, wash with cold water. The
rapid deployment sequence and airbag
fabric may cause friction and skin burns.
33
01 Safety
Child safety
01
Children should sit comfortably and
safely
Volvo recommends that children travel in
rear-facing child seats until as late an age as
possible, at least until 3-4 years of age, and
then front-facing booster cushions/child seats
until up to 10 years of age.
NOTE
WARNING
In the event of questions when fitting child
safety products, contact the manufacturer
for clearer instructions.
Child seats
Look in the installation instructions for the
child seat for the correct fitting.
The position of a child in the car and the
choice of equipment are dictated by the
child's weight and size, for more information,
see page 35.
Location of child seats
You may place:
NOTE
Regulations regarding the placement of
children in cars vary from country to country. Check what does apply.
1
34
G020128
Children of all ages and sizes must always sit
correctly secured in the car. Never allow a
child to sit on the knee of a passenger.
Volvo's own child safety equipment is
designed for your car. Volvo recommends
that you use Volvo genuine equipment to best
ensure that the mounting points and attachments are correctly positioned and are sufficiently strong.
Do not attach the child seat's straps in the
seat's horizontal adjustment bar, springs
or rails and beams under the seat. Sharp
edges may damage the straps.
Child seats and airbags are not compatible.
NOTE
When using other child safety products it
is important to read the installation instructions included with the product.
For information on activating/deactivating the airbag (SRS), see page 24.
•
a child seat/booster cushion on the front
passenger seat, provided the passenger
airbag is not activated1.
•
one or more child seats/booster cushions
in the rear seat.
Always fit child seats/booster cushions in the
rear seat if the passenger airbag is activated.
A child sitting on the front passenger seat
could suffer serious injury if the airbag
deploys.
01 Safety
Child safety
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag (SRS) is activated.2
No one shorter than 140 cm should ever
sit in the front passenger seat if the airbag
(SRS) is activated.
Failure to follow the advice given above
can endanger life.
WARNING
01
Label Airbag
Booster cushions/child seats with steel
braces or some other design that could
rest on the seatbelt buckle's opening button must not be used, as they could cause
the seatbelt buckle to open accidentally.
Do not allow the upper section of the child
seat to rest against the windscreen.
The label becomes visible when the passenger
door is opened; see the illustration on page 24.
Recommended child seats3
Weight
Front seat (with deactivated airbag)
Group 0
Volvo infant seat (Volvo Infant Seat) - rear-facing child seat, secured with the car's seatbelt
<10 kg
Type approval: E1 04301146
Group 0+
(U)
<13 kg
Group 0
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt and straps.
<10 kg
Type approval: E5 04215
Group 0+
(L)
<13 kg
2
3
For information on activated/deactivated airbag (SRS), see page 24.
For other child seats your car should be included in the manufacturer's enclosed list of vehicles or be universally approved in accordance with the ECE R44 legal requirement.
}}
35
01 Safety
01
Child safety
Weight
Front seat (with deactivated airbag)
Group 0
Child seats which are universally approved.
<10 kg
(U)
Group 0+
<13 kg
Group 1
9-18 kg
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's seatbelt and
straps.
Type approval: E5 04192
(L)
Group 1
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt and straps.
9-18 kg
Type approval: E5 04215
(L)
Group 1
Child seats which are universally approved.
9-18 kg
(U)
Group 2
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - rear-facing child seat, secured with the car's seatbelt and
straps
15-25 kg
Type approval: E5 04192
(L)
Group 2
Volvo rear-facing/turnable child seat (Volvo Convertible Child Seat) - front-facing child seat, secured with the car's seatbelt.
15-25 kg
Type approval: E5 04191
(U)
36
01 Safety
Child safety
Weight
Front seat (with deactivated airbag)
Group 2/3
Booster cushion with and without backrest (Booster Cushion with and without backrest).
15-36 kg
Type approval: E5 04216
01
(UF)
Group 2/3
Volvo booster seat with backrest (Volvo Booster Seat with backrest).
15-36 kg
Type approval: E1 04301169
(UF)
L: Suitable for specific child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
U: Suitable for universally approved child seats in this weight class.
UF: Suitable for front-facing universally approved child seats in this weight class.
}}
37
01 Safety
01
Child safety
Weight
Second row of seats, outer seatsA
Second row of seats, centre seatA
Group 0
Volvo infant seat (Volvo Infant Seat) - rear-facing child seat,
secured with the car's seatbelt.
Volvo infant seat (Volvo Infant Seat) - rearfacing child seat, secured with the car's seatbelt.
<10 kg
Group 0+
<13 kg
Group 0
<10 kg
Group 0+
<13 kg
Group 0
<10 kg
Group 0+
<13 kg
(U)
Type approval: E1 04301146
(U)
Volvo infant seat (Volvo Infant Seat) - rear-facing child seat,
secured with the ISOFIX fixture system.
Type approval: E1 04301146
(L)
Rear-facing child seat (Child Seat) - rear-facing child seat,
secured with the car's seatbelt, straps and support legs.
Type approval: E5 04215
(L)
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt, straps and support legs.
Type approval: E5 04215
(L)
Group 0
Child seats which are universally approved.
Child seats which are universally approved.
<10 kg
(U)
(U)
Group 0+
<13 kg
38
Type approval: E1 04301146
Third row of
seats in cars
seating seven
Child seats which
are universally
approved.
(U)
01 Safety
Child safety
Weight
Second row of seats, outer seatsA
Group 1
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps.
9-18 kg
Second row of seats, centre seatA
01
Third row of
seats in cars
seating seven
Type approval: E5 04192
(L)
Group 1
9-18 kg
Rear-facing child seat (Child Seat) - rear-facing child seat,
secured with the car's seatbelt and straps.
Type approval: E5 04215
(L)
Group 1
9-18 kg
Rear-facing child seat (Child Seat) - rear-facing child seat, secured with the car's seatbelt, straps and support legs.
Type approval: E5 04215
(L)
Britax Fixway – rear-facing child seat, secured with the ISOFIX fixture system and straps.
Type approval: E5 03171
(L)
Group 1
Child seats which are universally approved.
Child seats which are universally approved.
9-18 kg
(U)
(U)
Child seats which
are universally
approved.
(U)
}}
39
01 Safety
01
Child safety
Weight
Second row of seats, outer seatsA
Group 2
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - rear-facing child seat, secured with the car's
seatbelt and straps.
15-25 kg
Second row of seats, centre seatA
Third row of
seats in cars
seating seven
Type approval: E5 04192
(L)
Group 2
15-25 kg
Group 2/3
15-36 kg
Volvo rear-facing/turnable child seat (Volvo Convertible
Child Seat) - front-facing child seat, secured with the car's
seatbelt.
Volvo rear-facing/turnable child seat (Volvo
Convertible Child Seat) - front-facing child
seat, secured with the car's seatbelt.
Type approval: E5 04191
Type approval: E5 04191
(U)
(U)
Booster cushion with and without backrest (Booster
Cushion with and without backrest).
Booster cushion with and without backrest
(Booster Cushion with and without backrest).
Type approval: E5 04216
Type approval: E5 04216
(UF)
(UF)
Booster cushion with
and without backrest
(Booster Cushion
with and without
backrest).
Type approval: E5
04216
(UF)
40
01 Safety
Child safety
Weight
Second row of seats, outer seatsA
Second row of seats, centre seatA
Third row of
seats in cars
seating seven
Group 2/3
Volvo booster seat with backrest (Volvo Booster Seat with
backrest).
Volvo booster seat with backrest (Volvo
Booster Seat with backrest).
Type approval: E1 04301169
Type approval: E1 04301169
(UF)
(UF)
Volvo booster seat
with backrest (Volvo
Booster Seat with
backrest).
15-36 kg
01
Type approval: E1
04301169
(UF)
Group 2/3
15-36 kg
Integrated booster cushion (Integrated
Booster Cushion) - available as a factory fitted option.
Type approval: E5 04215
(B)
L: Suitable for specific child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
U: Suitable for universally approved child seats in this weight class.
UF: Suitable for front-facing universally approved child seats in this weight class.
B: Built-in child seats approved for this weight class.
A
In cars seating seven, the seat row must be in its rearmost position when using a child seat.
}}
41
01 Safety
Child safety
01
Integrated booster cushion*
1. Pull the handle on the front of the booster
cushion forwards and then up so that the
booster cushion is raised.
WARNING
Never place a child in a child seat or on a
booster cushion in the front seat if the airbag (SRS) is activated.
2. Grasp the cushion with both hands and
push it backwards.
No one shorter than 140 cm should ever
sit in the front passenger seat if the airbag
(SRS) is activated.4
3. Push until the cushion locks in place.
WARNING
Failure to follow the advice given above
can endanger life.
The booster cushion must be in the locked
position before the child is placed there.
Raising the booster cushion
G031071
Check that:
•
•
G030708
Volvo's integrated booster cushion for the
centre rear seat is specially designed to provide optimum safety for children. Combined
with the regular seatbelts the integrated
booster cushion is approved for children
weighing between 15 and 36 kg.
4
42
For information on activated/deactivated airbag (SRS), see page 24.
* Option/accessory, for more information, see Introduction.
the seatbelt is locked.
the seatbelt is in contact with the child's
body and is not slack or twisted, and that
the seatbelt is positioned correctly across
the shoulder.
•
the lap belt is low over the pelvis for optimum protection.
•
the seatbelt does not lie across the
child's throat or below the shoulder.
•
Carefully adjust the position of the head
restraint to suit the child.
01 Safety
Child safety
WARNING
Volvo recommends that repair or replacement is only carried out by an authorised
Volvo workshop. Do not make any modifications or additions to the booster cushion.
If an integrated booster cushion has been
subjected to a major load, such as in conjunction with a collision, the entire booster
cushion must be replaced. Even if the
booster cushion appears to be undamaged, it may not afford the same level of
protection. The booster cushion must also
be replaced if it is heavily worn.
Child safety locks, rear doors
Press the seat cushion down to access the
mounting points.
The controls for operating the rear door
power windows and the rear door opening
handles can be blocked from opening from
the inside. For more information see
page 130.
Always follow the manufacturer's installation
instructions when connecting a child seat to
the ISOFIX mounting points.
Size classes
ISOFIX fixture system for child seats*
1. Pull the handle forwards.
Size
class
G015268
2. Move the cushion down and press until it
locks.
Remember to stow away the booster
cushion before lowering the rear seat
backrest.
Child seats are in different sizes – cars are in
different sizes. This means that not all child
seats are suitable for all seats in all car models.
Consequently, there is a size classification for
child seats using the ISOFIX fixture system in
order to assist users in choosing the correct
child seat (see the following table).
Lowering the booster cushion
NOTE
01
Mounting points for the ISOFIX fixture system
are concealed behind the lower section of the
rear seat backrest, in the outer seats.
The location of the mounting points is indicated by symbols in the backrest upholstery
(see preceding illustration).
Description
A
Full size, front-facing child
seat
B
Reduced size (alt. 1), frontfacing child seat
B1
Reduced size (alt.2), front-facing child seat
C
Full size, rear-facing child seat
}}
* Option/accessory, for more information, see Introduction.
43
01 Safety
01
Child safety
Size
class
WARNING
Description
D
Reduced size, rear-facing
child seat
E
Rear-facing infant seat
F
Transverse infant seat, lefthand
G
Transverse infant seat, righthand
NOTE
Never place the child in the passenger
seat if the car is fitted with an activated airbag.
Volvo recommends that you contact an
authorised Volvo dealer for recommendations about which ISOFIX child seats Volvo
recommends.
NOTE
If an ISOFIX child seat has no size classification, the car model must be included on
the vehicle list for the child seat.
Types of ISOFIX child seat
Type of child seat
Infant seat transverse
Infant seat, rear-facing
Weight
Passenger seats for ISOFIX installation of child seats
Front seat
Outer rear seat
max 10 kg
F
X
X
(0 – 9 months)
G
X
X
max 10 kg
E
X
OK
(0 – 9 months)
44
Size class
(IL)
01 Safety
Child safety
Type of child seat
Infant seat, rear-facing
Weight
max 13 kg
Size class
E
01
Passenger seats for ISOFIX installation of child seats
Front seat
Outer rear seat
X
OK
(0 – 12 months)
(IL)
D
X
OK
(IL)
C
X
OK
(IL)
Child seat, rear-facing
9-18 kg
D
X
(9-36 months)
OK
(IL)
C
X
OK
(IL)
}}
45
01 Safety
Child safety
01
Type of child seat
Front-facing child seat
Weight
9-18 kg
Size class
B
Passenger seats for ISOFIX installation of child seats
Front seat
Outer rear seat
X
OKA
(9-36 months)
(IUF)
B1
X
OKA
(IUF)
A
X
OKA
(IUF)
X: The ISOFIX position is not suitable for ISOFIX child seats in this weight class and/or size class.
IL: Suitable for specific ISOFIX child seats. These child seats may be intended for use in a special car model, limited or semi-universal categories.
IUF: Suitable for front-facing ISOFIX child seats that are universally approved in this weight class.
A
46
Volvo recommends rear-facing child seats for this group.
01 Safety
Child safety
Mounting points for child seat
Fold the backrest forward to access the
mounting points. For detailed information on
how the child seat should be tensioned in the
upper mounting points, see the seat manufacturer's instructions.
Extra locking function in seatbelt (ALR/
ELR)5
01
This function is automatically deactivated
when the seatbelt is released from the buckle
and retracts back to its starting position.
If there are any problems with installation of
child safety products, contact the manufacturer for clearer installation instructions.
G027032
The seatbelt in the centre of the second row
of seats has an extra locking function (ALR/
ELR). The locking function helps to hold the
belt taut in order to facilitate child seat installation.
The car is equipped with upper mounting
points for child seats. These mounting points
are located on the rear of the rear seats.
The upper mounting points are primarily
intended for use with front-facing child seats.
Volvo recommends that small children should
sit in rear-facing child seats to as late an age
as possible.
NOTE
These mounting points are only on the
second row of seats in cars seating seven.
5
When installing a child seat with the help of
the seatbelt:
1. Secure the seatbelt in the child seat following the instructions of the child seat
manufacturer.
2. Pull out the entire seatbelt.
3. Lock the seatbelt by inserting the locking
tab in the buckle. A clear "click" indicates
that the seatbelt has locked.
4. Allow the seatbelt mechanism to retract
the seatbelt while stretching it around the
child seat. A mechanical sound will be
audible from the seatbelt. This is normal.
Automatic Locking Retractor/Emergency Locking Retractor.
47
Overview, left-hand drive cars................................................................
Overview, right-hand drive cars..............................................................
Driver's door control panel.....................................................................
Combined instrument panel....................................................................
Indicator and warning symbols...............................................................
Information display..................................................................................
Switches in the centre console...............................................................
Lighting panel..........................................................................................
Left-hand stalk switch.............................................................................
Trip computer*........................................................................................
Right-hand stalk switch..........................................................................
Cruise control*........................................................................................
Parking brake, electrical socket, etc.......................................................
Power windows.......................................................................................
Windows, rearview and door mirrors......................................................
Power sunroof*.......................................................................................
48
* Option/accessory, for more information, see Introduction.
50
52
54
55
57
60
61
64
67
68
70
73
75
77
79
84
INSTRUMENTS AND CONTROLS
02 Instruments and controls
Overview, left-hand drive cars
02
50
02 Instruments and controls
Overview, left-hand drive cars
Lighting panel
Horn
Panel vents
Cruise control
Display
Direction indicators, dipped-main beam
switch, READ button
Temperature gauge
Odometer, trip meter, cruise control
Speedometer
Direction indicators
Tachometer
Outside temperature, clock, gear position
Fuel gauge
02
Parking brake
Parking brake release
Switches, reading lamps
Interior lighting
Sunroof control
Seatbelt reminder
Rearview mirror
Indicator and warning symbols
Panel vents
Glovebox
Hazard warning flashers
Audio system
Climate control
Windscreen wipers
Keypad for phone/audio
Combined instrument panel
51
02 Instruments and controls
Overview, right-hand drive cars
02
52
02 Instruments and controls
Overview, right-hand drive cars
Lighting panel
Cruise control
Panel vents
Horn
Indicator and warning symbols
Combined instrument panel
Fuel gauge
Phone/Audio keypad
Outside temperature, clock, gear position
Windscreen wipers
Tachometer
Parking brake release
Direction indicators
Switches, reading lamps
Speedometer
Interior lighting
Odometer, trip meter, cruise control
Sunroof control
Temperature gauge
Seatbelt reminder
Display
Rearview mirror
02
Panel vents
Glovebox
Hazard warning flashers
Audio system
Climate control
Direction indicators, dipped-main beam
switch, READ button
Parking brake
53
02 Instruments and controls
Driver's door control panel
Control panel
G029570
02
Lock button, for all doors
Blocking power windows in the rear
doors
Power window controls
Door mirror control
54
02 Instruments and controls
Combined instrument panel
G026973
02
Temperature gauge – Displays the temperature of the engine cooling system. A
message will appear on the display if the
gauge goes into the red zone. Bear in
mind that extra lights placed in front of
the air intake reduce the cooling capacity
of the system.
Display – The display shows information
and warning messages.
Speedometer – Shows the speed of the
car.
Trip meters T1 and T2 – Used for measuring short distances. The right-hand digit
displays tenths of a kilometre. Press the
button for more than 2 seconds to reset.
Switch between trip meters with one
quick press of the button.
Automatic gearbox indicator – The
selected gear position is displayed here.
Cruise control indicator.
Outside temperature gauge – When the
temperature lies between +2 °C to -5 °C,
a snowflake symbol illuminates in the display. This warns of icy roads. If the car
has been stationary, the gauge may display a reading that is too high.
Odometer – The odometer indicates the
total distance the car has travelled.
Main beam indicator
Warning symbol – If a fault arises, the
symbol illuminates and a message is
shown in the display.
Tachometer – Indicates engine speed in
thousands of revolutions per minute
(rpm). Do not allow the tachometer gauge
to enter the red zone.
Knob for clock – Turn the knob to adjust
the time.
When the lamp in the instrument illuminates the level in the fuel tank is low,
refuel as soon as possible. See also Trip
computer page 68.
}}
55
02 Instruments and controls
Combined instrument panel
Indicator and warning symbols
02
56
Direction indicators – left/right
02 Instruments and controls
Indicator and warning symbols
Functionality check, symbols
Certain symbols may have no
function, depending on the car's
specifications.
Red symbol
1. Stop the car in a safe place. Do not drive
the car further. Do not drive the car further.
02
2. Read the information on the display.
Symbols in the centre of the
instrument panel
3. Rectify in accordance with the instructions in the display or contact a workshop. Volvo recommends that you seek
assistance from an authorised Volvo
workshop.
Symbol and message text are visible until the
fault has been rectified.
Yellow symbol
–
All indicator and warning symbols1 illuminate
when the remote control key is turned to
position II before starting. This is to check
that the symbols are working. When the
engine starts, all the symbols should go out
except the parking brake symbol, which only
goes out when the brake is disengaged.
If the engine does not start within
5 seconds, all symbols extinguish
except the symbols for a fault in
the car's emissions system and
for low oil pressure.
1
Read the message in the display. Action.
The message text is cleared using the READ
button, see page 60, or it disappears automatically after 2 minutes.
NOTE
These symbols illuminate with a
red or amber glow depending on
the severity of the fault.
For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 213.
When the message text TIME FOR
REGULAR SERVICE is shown, the symbol and message text are cleared using
the READ button, or disappear automatically after 2 minutes.
}}
57
02 Instruments and controls
Indicator and warning symbols
Indicator symbols
02
ABS fault
If this symbol illuminates then the
system is not working. The car's
regular brake system continues to
work, but without the ABS function.
2. If the reservoir level is below MIN then
the car should not be driven further, but
recovered instead. Volvo recommends
that the car is transported to an authorised Volvo workshop to have the brake
system checked.
If the BRAKE and ABS symbols
illuminate at the same time, there
may be a fault in the brake force
distribution system.
1. Stop the car in a safe place and turn off
the engine.
2. Restart the engine.
3. Volvo recommends that drive to an
authorised Volvo workshop to have the
ABS system checked if the symbol
remains illuminated.
Fault in brake system
If this symbol illuminates, the
brake fluid level may be too low.
1. Stop the car in a safe place and check
the level in the brake fluid reservoir, see
page 216.
2
58
•
If the level in the brake fluid reservoir is
below MIN then the car should not be
driven any further. Have the car transported to an authorised workshop recommended by Volvo to have the brake system checked.
WARNING
If the BRAKE and ABS symbols are illuminated at the same time, there is a risk that
the rear end will skid during heavy braking.
Seatbelt reminder
1. Stop the car in a safe place and turn off
the engine.
2. Restart the engine.
•
If both symbols extinguish, continue driving.
•
If the symbols remain illuminated, check
the level in the brake fluid reservoir, see
page 216.
•
If the brake fluid reservoir's level is normal
but the symbols are still illuminated, the
car can be driven, with great care, to an
authorised workshop recommended by
Volvo to have the brake system checked.
For certain engine variants, the symbol for low oil pressure is not used. Warnings are given via display text, see page 213.
This symbol illuminates if someone in a front seat has not put on
their seatbelt.
Low oil pressure2
If this symbol illuminates during
driving then the engine's oil pressure is too low. Stop the engine
immediately and check the engine
oil level, top up if necessary. If the
symbol illuminates and the oil level is normal,
contact an authorised workshop recommended by Volvo.
02 Instruments and controls
Indicator and warning symbols
Emissions system
inspection.
The symbol illuminates when the
parking brake is depressed.
Always depress the parking brake
to its lowest position.
NOTE
Airbags – SRS
If this symbol remains illuminated
or illuminates while driving, it
means a fault has been detected
in the seatbelt buckle, SRS, SIPS
or IC system. Volvo recommends
that drive directly to an authorised Volvo
workshop for inspection.
Alternator not charging
If this symbol illuminates while
driving, a fault has occurred in the
electrical system. Volvo recommends that you visit an authorised Volvo workshop.
Engine preheater (diesel)
guished.
Parking brake applied
If the symbol illuminates then it
may be due to a fault in the car's
emissions system. Volvo recommends that you drive to an
authorised Volvo workshop for
This symbol illuminates during
engine preheating. Preheating
occurs when the temperature is
below -2 °C. The car can be
started once the symbol is extin-
The symbol illuminates irrespective of how
hard the parking brake is depressed.
Rear fog lamp
This symbol is lit when the rear
fog lamp is on.
Indicator symbol for trailer
is faulty.
This symbol flashes when the
direction indicators are used and
the trailer is connected. If the
symbol does not flash then one of
the lamps on the trailer or the car
Reminder – doors not closed
If one of the doors or the tailgate is not properly closed the driver will be reminded of this.
02
Low speed
If the car moves at a speed less than
about 7 km/h, the information symbol illuminates and DRIVER DOOR OPEN ,
PASSENGER DOOR OPEN ,LEFT REAR
DOOR OPEN or RIGHT REAR DOOR
OPEN is shown in the display at the same
time. Stop the car safely as soon as possible
and close the door or bonnet.
High speed
If the car is moving faster than
about 7 km/h then the symbol
illuminates and one of the texts
indicated in the previous paragraph appears in the display at
the same time.
Tailgate reminder
If the tailgate is open, TAILGATE OPEN will
appear on the display.
Stability system DSTC
For information on the system's
functions and symbols, see
page 154.
59
02 Instruments and controls
Information display
Messages
02
When a warning or indicator symbol illuminates, it is supplemented by a message
appearing on the display.
–
Press the READ button (1).
Switch between messages with the READ
button. Fault messages are stored in the
memory until the fault is rectified.
NOTE
If a warning message appears while you
are using the trip computer, the message
must be read (press READ) before the previous activity can be resumed.
60
Message
Specification
Message
Specification
STOP
SAFELYA
Stop the car in a safe
manner and turn off the
engine. Serious risk of
damage.
TIME FOR
REGULAR
SERVICE
STOP
ENGINEA
Stop the car in a safe
manner and turn off the
engine. Serious risk of
damage.
SERVICE
URGENTA
Volvo recommends that
you engage an authorised Volvo workshop to
check the car immediately.
Time for regular service.
Volvo recommends that
you engage an authorised Volvo workshop to
carry out the service.
The timing is determined by the number of
kilometres driven, number of months since the
last service and engine
running time.
SOOT FILTER
FULL SEE
MANUAL
Diesel particle filter
requires regeneration,
see page 143.
DSTC SPIN
CONTROL
OFF
The function of the stability and traction control system is reduced,
see page 153 for more
variants.
SEE MANUALA
Read the owner's manual.
SERVICE
REQUIREDA
Volvo recommends that
you engage an authorised Volvo workshop to
check the car as soon
as possible.
A
Part of message, shown together with information on
where the problem has arisen.
02 Instruments and controls
Switches in the centre console
Switch
G026944
02
NOTE
The order of the buttons may vary.
Air conditioning in the rear of the
passenger compartment*
Press the button to activate
the air conditioning in the rear
of the passenger compartment. Rear passenger compartment air conditioning is
deactivated when the ignition
is switched off.
Child safety locks in the rear doors*
Retractable power door mirrors*
Activating or deactivating the
electric child safety locks in
the rear doors. The remote
control key must be in position
I or II. When the child safety
locks are activated, the lamp
in the button illuminates. A message is shown
in the display when the child safety locks are
activated or deactivated, see page 130.
Used to fold in the door mirrors if they are folded out or to
fold them out if they are folded
in.
Proceed as follows if a door mirror has been
accidentally folded in or out:
1. Manually adjust the appropriate door mirror to its normal position.
2. Turn the remote control key to position II.
}}
* Option/accessory, for more information, see Introduction.
61
02 Instruments and controls
Switches in the centre console
02
3. Fold the door mirror inward and then outward using the button.
The door mirrors have now returned to their
original fixed positions.
Park Assist*
The system is always activated when the car is started.
Press the button to deactivate/
reactivate the parking assistance system. See also page
155.
Deactivation of the deadlocks* and
detectors
Use this button when you wish
to switch off the deadlock
function (doors cannot be
opened from the inside when
locked). This button can also
be used when deactivating the
alarm system's movement and tilt detectors*.
The lamp illuminates when these systems are
shut down/deactivated, see pages 129 and
132.
Active Xenon headlamps*
If the car is equipped with
active Xenon headlamps
(Active Bending Lights, ABL)
the light from the headlamps
follows the steering wheel
movement during driving. The
function is activated automatically when the
car is started and can be deactivated/activated by pressing the button. The lamp in the
button illuminates when the function is activated
Shifting headlamp pattern for right/lefthand traffic
Hold the button depressed for at least 5 seconds. The car must be stationary when the
headlamp pattern is adjusted. The message
HEADLIGHTS SET FOR RH TRAFFIC or
HEADLIGHTS SET FOR LH TRAFFIC is
shown in the display. For more information
and adapting headlamp pattern for halogen
or Dual Xenon headlamps, see page 173.
Electric socket/Cigarette lighter*
Auxiliary lamps*
Use this button to switch the
auxiliary lamps on with main
beam or to switch them off.
62
* Option/accessory, for more information, see Introduction.
The electrical socket can be
used for 12 V accessories,
such as mobile phone chargers and coolers.
The remote control key must be at least in
position I so that the socket can supply
power.
The cigarette lighter is activated by pushing in
the button. The button pops out when the
lighter is hot. Pull out the lighter and light a
cigarette on the heated coils. For safety reasons, always keep the cover in place when
the socket is not in use. Max. current tap
10 A.
WARNING
Always leave the plug in the socket when
the socket is not in use.
IMPORTANT
Max. socket is 10 A (120 W) if one socket
is used at a time. If both sockets (in the
centre console and by the rear seat) are
used at the same time then 7.5 A (90 W)
per socket applies.
If the compressor for emergency puncture
repair is connected to one of the two sockets then no other current consumers may
be connected to the other one.
02 Instruments and controls
Switches in the centre console
Use the hazard warning flashers (all direction
indicators flash) when the car is stopped
where it could be a traffic hazard or obstruction. Press the button to activate the function.
NOTE
The compressor for emergency puncture
repair is tested and approved by Volvo.
For information about using Volvo's recommended temporary mobility kit (TMK)
for emergency puncture repair, see
page 190.
02
NOTE
BLIS - Blind Spot Information System*
Press the button to deactivate
or reactivate the function. see
page 157 for further information.
Hazard warning flashers
Regulations regarding the use of hazard
warning flashers vary from country to
country.
Rear window and door mirror
defrosters
Heating is used to quickly
remove misting and ice from
the rear window and door mirrors. Press the switch to start
defrosting the rear window
and door mirrors. The lamp in
the switch illuminates. The
light in the switch is lit.
Defrosting is automatically disconnected after about
12 minutes.
Heated front seats
AM FM
CD
LUM
VO E
POWER
1
4
GHI
7
PQRS
*
3
DEF
5
6
JKL
MNO
8
9
TUV WXYZ
0
#
G027096
2
ABC
For heated front seats, see
page 91 or 93 for further
information.
* Option/accessory, for more information, see Introduction.
63
02 Instruments and controls
Lighting panel
General
02
Position
Specification
Automatic/deactivated dipped
beam. Only main beam flash.
Daytime running lights when
the car is being driven. Automatic switching to parking
lights when the car is parked.
Automatic dipped beam. Main
beam and main beam flash
work in this position.
Light switches
Automatic daytime running lights during
the day.
Thumbwheel for headlamp levelling
Rear fog lamp
Thumbwheel for adjusting instrument
lighting
Headlamps
Automatic dipped beam*
Dipped beam comes on automatically when
the remote control key is turned to position II,
except when the headlamp control (1) is in
the centre position. If necessary, the automatic dipped beam can be deactivated. Volvo
recommends that you engage an authorised
Volvo workshop to have it deactivated.
Automatic dipped beam, main beam
1. Turn the remote control key to position II.
2. Dipped beam is activated by means of
turning the headlamp control (1) clockwise to the end position.
64
* Option/accessory, for more information, see Introduction.
3. Main beam is activated by means of moving the left-hand stalk switch towards the
steering wheel to the end position and
releasing it, see page 67.
The lamps are switched off automatically
when the remote control key is turned to
position I or 0.
Position/parking lamps
Position/parking lamps can be switched on
irrespective of remote control key position.
–
Turn the headlamp control (1) to the centre position.
When the remote control key is in position II
the position/parking lamps and number plate
lighting are always on.
Headlamp levelling
The load in the car changes the vertical alignment of the headlamp beam, which could
dazzle oncoming motorists. Avoid this by
adjusting the height of the beam.
1. Turn the remote control key to position II.
2. Turn the headlamp control (1) to one of
the end positions.
3. Roll the thumbwheel (3) up or down
respectively to raise or lower beam alignment.
02 Instruments and controls
Lighting panel
Cars with Xenon headlamps* have automatic
headlamp levelling, so there is no thumbwheel (3).
Active Xenon headlamps*
Daytime running lights during the day.
To save fuel, daytime running lights (Daytime
Running Light) can be selected during the day
instead of the more energy-intensive dipped
beam. The daytime running lights mounted in
the spoiler use bright, low-energy diode technology.
Instrument lighting
The instrument lighting is switched on when
the remote control key is in position II and the
headlamp control (1) is in one of the end positions. The lighting is automatically dimmed
during the day and can be controlled manually at night.
Rear fog lamp
The rear fog lamp can only be switched on in
combination with the headlamps.
–
Press the button (4).
The rear fog lamp indicator symbol on the
combined instrument panel and the light in
the button illuminate when the rear fog lamp
is switched on.
NOTE
G020789
Roll the thumbwheel (5) up or down for
brighter or dimmer lighting.
Headlamp pattern for active/non-active headlamps.
If the car is equipped with active Xenon headlamps (Active Bending Lights, ABL) the light
from the headlamps follows the steering
wheel movement during driving. The function
is activated automatically when the car is
started and can be deactivated/activated
using the button in the centre console, see
page 62.
02
Press the button (2) and turn the headlamp
control (1) clockwise to the end position in
order to activate the daytime running lights
during daytime. This is regulated by a light
sensor which switches from daytime running
lights to dipped beam off the main headlamps
at dusk or when the daylight becomes too
weak. The light in the button illuminates when
the daytime running lights are activated.
NOTE
To achieve minimal energy consumption,
the rear lights are also switched off when
switching automatically from dipped beam
to daytime running lights.
Regulations for use of fog lamps vary from
country to country.
* Option/accessory, for more information, see Introduction.
65
02 Instruments and controls
Lighting panel
WARNING
02
This system help to save energy - it cannot
determine in all situations when daylight is
too weak or sufficiently strong, e.g. in mist
and rain.
The driver is always responsible for ensuring that the car is driven with its lights in a
correct state and in accordance with applicable traffic regulations.
66
02 Instruments and controls
Left-hand stalk switch
Stalk switch positions
Direction indicators
Continuous flash sequence
–
Move the stalk switch up or down to end
position (B).
The stalk switch remains in its end position
and is moved back manually, or automatically
by steering wheel movement.
Short flash sequence
–
Short flash sequence, direction indicators
Continuous flash sequence, direction
indicators
Main beam flash
Home safe lighting and switching of
dipped and main beam
Move the stalk switch up or down to
position (A) and release, the stalk switch
then returns to its home position, or move
the stalk switch to position (B) and move
it directly back to the home position.
The direction indicators flash three times.
Short flash sequence interrupted immediately
if indicating is started in the opposite direction.
Main beam flash
–
Move the stalk switch gently towards the
steering wheel to position (C).
02
Main beam comes on until the stalk switch is
released.
Home safe light duration
Some of the exterior lighting can be kept
switched on to work as home safe lighting
after the car has been locked. The standard
delay is 30 seconds1, but can be changed to
60 or 90 seconds.
1. Remove the remote control key from the
ignition switch.
2. Move the stalk switch towards the steering wheel to the end position (D) and
release.
3. Get out of the car and lock the door.
Switching, main and dipped beam
The remote control key must be in position II
for main beam to be switched on.
1. Turn the headlamp control clockwise to
the end position, see page 64.
2. Move the stalk switch towards the steering wheel to the end position (D) and
release.
1
Factory settings.
67
02 Instruments and controls
Trip computer*
General
NOTE
If a warning message interrupts while you
are using the trip computer, this message
must be acknowledged. Acknowledge by
pressing the READ button and revert to
the trip computer function.
02
Functions
The trip computer displays the following information:
READ - confirms
Thumbwheel - browse between menus
and options in the trip computer list
RESET – resets
Controls
To scroll through trip computer information,
turn the thumbwheel (2) either up or down in
steps. Continue turning to return to the starting point.
1
2
68
•
•
•
•
•
•
--- KM/H AVERAGE SPEED
--.- KM/L INSTANTANEOUS
--.- KM/L AVERAGE
--- KILOMETRES TO EMPTY TANK
DSTC ON , see page 153
--- MPH ACTUAL SPEED 1*
AVERAGE SPEED
When the ignition is switched off, the average
speed is stored and used as the basis of the
new value when you continue driving. Reset
using the RESET button.
INSTANTANEOUS
Current fuel consumption is calculated every
second. The information on the display is
updated every couple of seconds. When the
Only in certain markets.
Only applies to diesel cars with particle filter.
* Option/accessory, for more information, see Introduction.
car is stationary, "----" appears on the display. During the period for regeneration2 fuel
consumption may increase, see page 143.
AVERAGE
The average fuel consumption since the last
reset. Reset using RESET.
NOTE
There may be a slight error in the reading if
a fuel-driven parking heater* has been
used.
KILOMETRES TO EMPTY TANK
The calculation is based on the average fuel
consumption over the last 30 km and the
remaining driveable fuel quantity. The display
shows the approximate distance that can be
driven with the fuel quantity remaining in the
tank. No guaranteed range remains when the
display shows "--- KILOMETRES TO
EMPTY TANK ". Refuel as soon as possible.
NOTE
There may be a slight error in the reading if
a fuel-driven parking heater* has been
used or if driving style has been changed.
02 Instruments and controls
Trip computer*
MPH ACTUAL SPEED.*1
Current speed is displayed in mph if the
speedometer is graduated in km/h. If it is
graduated in mph then the current speed is
shown in mph.
02
Resetting
1. Select --- KM/H AVERAGE SPEED or
--.- KM/L AVERAGE
2. Press and hold the RESET button (3) for
at least five seconds to reset the average
speed and average consumption at the
same time.
1
Only in certain markets.
* Option/accessory, for more information, see Introduction.
69
02 Instruments and controls
Right-hand stalk switch
Windscreen wipers
Single sweep
Raise the stalk switch to make a
single sweep.
02
Intermittent wiping
G026953
You can set a suitable delay
between the sweeps. Turn the
thumbwheel up for a shorter interval between sweeps. Turn it down
to increase the delay.
Continuous wiping
The wipers sweep at normal
speed.
Wiper/washer function – windscreen.
The wipers sweep at high speed.
Thumbwheel
The windscreen wipers are off
when the stalk switch is in position 0.
Turn the thumbwheel upwards for higher sensitivity and downwards for lower sensitivity,
(an extra sweep is made when the thumbwheel is turned upwards).
On/Off
When activating the rain sensor, the remote
control key must be in position I or II and the
windscreen wiper stalk switch must be in
position 0 (not activated).
To activate the rain sensor:
IMPORTANT
Before activating the wipers during winter ensure that the wiper blades are not frozen
in and that any snow or ice on the windscreen (and rear window) is scraped away.
IMPORTANT
Use plenty of washer fluid when the wipers
are cleaning the windscreen. The windscreen must be wet when the windscreen
wipers are operating.
70
The rain sensor automatically activates the
windscreen wipers based on how much water
it detects on the windscreen. The sensitivity
of the rain sensor can be adjusted using the
thumbwheel.
–
Rain sensor - On/Off
Windscreen wipers off
Rain sensor*
* Option/accessory, for more information, see Introduction.
Press the button. A lamp in the button
illuminates to indicate that the rain sensor
is active.
To turn the rain sensor off, either:
•
Press the button. The lamp in the button
goes out.
•
Press the stalk switch downward to
another wiper program. If the stalk switch
is raised, the rain sensor will remain
active, the wipers make an extra sweep
and then return to rain sensor mode when
the stalk switch is released to position 0.
02 Instruments and controls
Right-hand stalk switch
The rain sensor is automatically deactivated
when the remote control key is removed from
the ignition switch or 5 minutes after the ignition is switched off.
IMPORTANT
The windscreen wipers could start and be
damaged in an automatic car wash. Deactivate the rain sensor by depressing button
(2) while the remote control key is in position I or II.
Reduced washing
Wiper and washer, rear window
If only approx. 1 litre of washer fluid remains
in the reservoir and the message that you
should fill the washer fluid is shown in the
combined instrument panel's display, then
the supply of washer fluid to the headlamps
and rear window is switched off. This is in
order to prioritise cleaning the windscreen
and the visibility through it.
02
Windscreen/headlamp washer
Move the stalk switch toward the steering
wheel to start the windscreen and headlamp
washers. The wipers will make several more
sweeps once the stalk switch is released.
High-pressure headlamp washing*
High-pressure headlamp washing consumes
a large quantity of washer fluid. To save fluid,
the headlamps are only washed every fifth
wash cycle (within a 10 minute period). When
10 minutes have elapsed following the latest
windscreen washing, the headlamps are
again washed with high-pressure with the first
windscreen washing. Turn the stalk switch
toward the steering wheel to wash the windscreen only.
1
Wiper/washer function – rear window.
Intermittent wiping: Depress the top of
the button.
Constant speed: Depress the bottom of
the button.
Move the stalk switch forward to start rear
window washing and wiping. The wiper blade
makes several extra sweeps once washing
has finished.
Wiper – reversing
Engaging reverse gear while the windscreen
wipers are on initiates intermittent rear window wiping.1. If the rear window wiper is
This function (intermittent wiping when reversing) can be deactivated. Volvo recommends that you visit an authorised Volvo workshop to have it deactivated.
* Option/accessory, for more information, see Introduction.
}}
71
02 Instruments and controls
Right-hand stalk switch
02
72
already on at normal speed, no change is
made.
02 Instruments and controls
Cruise control*
Activating
Increasing or decreasing speed
NOTE
A temporary increase in speed (less than
one minute) using the accelerator, such as
while overtaking, does not affect the cruise
control setting. When you release the
accelerator, the car will return to the programmed speed.
02
Temporary disengagement
G027098
G026949
–
The controls for cruise control are to the left
of the steering wheel.
Setting the desired speed:
1. Press the CRUISE button. CRUISE is
shown on the combined instrument
panel.
2. Touch + or – to lock the vehicle speed.
CRUISE-ON is shown.
Cruise control cannot be engaged at speeds
below 30 km/h or above 200 km/h.
1
–
Increase or decrease the speed by pressing and holding + or –. The speed of the
car when the button is released is set as
the new speed.
A brief press (less than half a second) on + or
– changes the speed by 1 km/h or 1 mph1.
Press 0 to disengage the cruise control
temporarily. CRUISE will be shown on
the combined instrument panel. The
speed set earlier is stored in the memory.
The cruise control is also temporarily disengaged when:
•
•
•
•
the brake pedal is depressed
speed falls when travelling uphill to below
25-30 km/h
the gear selector is moved to position N
wheel spin or wheel lock-up occurs.
Return to the set speed
Press this button to resume the
previously set speed. CRUISE
ON appears on the combined
instrument panel.
Depending on engine type.
* Option/accessory, for more information, see Introduction.
73
02 Instruments and controls
Cruise control*
Disengaging
02
74
–
Press CRUISE to disengage the cruise
control. CRUISE ON clears on the combined instrument panel.
* Option/accessory, for more information, see Introduction.
02 Instruments and controls
Parking brake, electrical socket, etc.
Parking brake
2. Depress the parking brake pedal firmly as
far as possible.
3. Release the foot brake pedal and make
sure that the car is at a standstill position.
02
4. If the vehicle rolls, the parking brake
pedal must be depressed further.
5. When parking the vehicle - select the
transmission's P position.
Parking brake, LHD car.
G026994
G026992
Parking on a hill
Parking brake, RHD car.
Parking brake pedal
Handle for releasing parking brake
The parking brake is at floor level, see illustration, and acts on the rear wheels when
depressed.
NOTE
The warning symbol in the combined
instrument panel illuminates irrespective of
how hard the parking brake pedal is
depressed.
If the car is parked facing uphill; turn the
wheels away from the kerb.
If the car is parked facing downhill, turn the
wheels towards the kerb.
WARNING
Always use the parking brake when parking on a slope - the automatic transmission's P position is not sufficient to hold
the car in all situations.
How to release the parking brake
1. Press the foot brake pedal down firmly.
2. Pull the handle.
How to apply the parking brake
1. Press the foot brake pedal down firmly.
}}
75
02 Instruments and controls
Parking brake, electrical socket, etc.
Electrical socket in the rear seat
IMPORTANT
Steering wheel adjustment
Max. socket is 10 A (120 W) if one socket
is used at a time. If both sockets (in the
centre console and by the rear seat) are
used at the same time then 7.5 A (90 W)
per socket applies.
02
If the compressor for emergency puncture
repair is connected to one of the two sockets then no other current consumers may
be connected to the other one.
The electrical socket can be used for various
accessories, such as mobile phone chargers
and coolers. It is designed for 12 V. For the
socket to supply current, the remote control
key must be in at least position I.
The compressor for emergency puncture
repair is tested and approved by Volvo.
For information about using Volvo's recommended temporary mobility kit (TMK)
for emergency puncture repair, see
page 190.
G026999
G028425
NOTE
The steering wheel can be adjusted for both
height and reach. Press down the control on
the left-hand side of the steering column.
Then adjust the steering wheel to the position
that suits you best. Press the control back
into place to lock the steering wheel. If this is
difficult, press the steering wheel slightly
while pressing the control back.
WARNING
Adjust the steering wheel before driving
off, never while driving. Check that the
steering wheel is fixed in position.
76
02 Instruments and controls
Power windows
Operating
The power windows are operated using the
controls in the doors. The key position must
be I or II for the power windows to operate.
The windows continue to work when the car
has stopped and the remote control key has
been removed, provided none of the doors is
opened. Operate the windows with caution.
To open a window:
–
Depress the front of the control.
To close a window:
–
Raise the front of the control.
NOTE
One way to reduce the pulsating wind
noise when the rear windows are open is
to also open the front windows slightly.
WARNING
Driver's door
If there are children in the car:
•
02
Always remember to switch off the
power supply to the power windows
by removing the remote control key if
the driver leaves the car.
•
Make sure that children or other passengers cannot be trapped in any way
when closing the windows.
If the rear door windows are operated from
the driver's door - check that none of the
rear seat passengers is in danger of getting their hands caught when closing the
windows.
Controls, power windows.
Front window controls
Rear window controls
The driver can operate all power windows
from the driver's seat. The windows can be
opened and closed in two ways:
•
Depress one of the controls (1) or (2) gently or raise them. The power windows go
up or down as long as the switch is actuated.
•
Fully depress one of the controls (1) or (2)
or raise it, then release. The side window
will then open or close automatically. If
}}
77
02 Instruments and controls
Power windows
02
the window is obstructed by an object,
the movement will stop.
remote control key) if you leave children in the
car unattended.
Rear power windows
The light in the switch is illuminated
NOTE
The rear door windows can only be operated
from the driver's door.
The function auto up for the passenger
side is only available in certain markets.
The light in the switch is extinguished
The rear door windows can be operated both
with the controls on each rear door and with
the controls on the driver's door.
Blocking power windows in the rear
doors
G029574
Front passenger seat
G029572
The rear door windows can be operated with
the controls on the doors and the switch on
the driver's door. If the light in the switch for
blocking power windows in the rear doors
(located in the driver's door control panel) is
illuminated, the rear door windows can only
be operated from the driver's door.
The power windows in the rear seat can be
blocked with the switch on the driver's door
control panel. Always remember to switch off
current to the power windows (i.e. remove the
78
G029573
Blocking rear power windows and electric child
safety locks*.
The control for the power window at the front
passenger seat operates that window only.
* Option/accessory, for more information, see Introduction.
WARNING
If the rear door windows are operated from
the driver's door, check that none of the
rear seat passengers are in danger of
becoming trapped in any way when they
are closed.
02 Instruments and controls
Windows, rearview and door mirrors
Interior rearview mirror
Interior rearview mirror with
compass*
example. The button is countersunk
approximately 2.5 centimetres in the mirror.
Correct zone on compass
Z
O
N
E
Normal position
Dimmed position.
Bright light from behind could be reflected in
the rearview mirror and dazzle the driver. Use
dimming when disturbed by light from
behind.
Automatic dimming*
Bright light from behind is automatically
dimmed by the rearview mirror.
Z
O
N
E
G026950
C
A
L
G026965
G026660
C
A
L
Dipping
02
The upper left-hand corner of the rearview
mirror has an integrated display that shows
the compass direction in which the front of
the car is pointing. Eight different directions
are shown with English abbreviations: N
(north), NE (north east), E (east), SE (south
east), S (south), SW (south west), W (west)
and NW (north west).
The earth is divided into 15 magnetic zones.
The compass is set for the geographic area to
which the car was delivered. The compass
should be calibrated if the car is moved
across several magnetic zones.
If the compass is activated then it starts automatically in key position II or when the engine
is running. Switch the compass on or off by
pressing the button set into the rear of the
mirror. Use a straightened paper clip for
2. Press and hold the button on the rear of
the mirror for approximately 3 seconds
until ZONE is shown (use a straightened
paper clip for example). The number for
the current area is shown.
1. Key position II.
}}
* Option/accessory, for more information, see Introduction.
79
02 Instruments and controls
Windows, rearview and door mirrors
02
80
3. Press the button several times until the
number for the required geographic area
(1–15) is shown. After several seconds
the display returns to show the compass
direction, this means that the change of
zone is complete.
02 Instruments and controls
Windows, rearview and door mirrors
02
Magnetic zones for the compass.
}}
81
02 Instruments and controls
Windows, rearview and door mirrors
Calibration
02
Door mirrors
WARNING
The compass may need calibrating to work
correctly. For best results, switch off all major
power consumers such as interior lighting,
ventilation fan, heated rear window etc. and
avoid having metal objects and magnetic
objects close to the mirror.
Adjust the mirrors before you begin driving.
Door mirrors with memory function*
If the car has door mirrors with memory function, they work together with the memory setting of the seat, see page 101.
1. Stop the car in a wide open area with the
engine running.
Memory function in remote control*
3. Drive slowly in a circle at a speed of no
more than 8 km/h until CAL disappears
from the display. Which is when calibration is complete.
4. Alternative calibration method: Drive off
as usual. CAL disappears from the display when calibration is complete.
G029575
2. Press and hold the button on the rear of
the rearview mirror (use a paper clip or
similar) until CAL is shown again (approx.
6 seconds).
The controls for adjusting the two door mirrors are at the front of the driver's door armrest. The rearview mirrors can be operated in
key position I and II.
1. Press the L button for the left-hand door
mirror or the R button for the right-hand
door mirror. The light on the button illuminates.
2. Adjust the position with the joystick in the
centre.
3. Press the L or R button again. The light
goes out.
Folding in the door mirrors, see page 61.
82
* Option/accessory, for more information, see Introduction.
When you unlock the car with one of the
remote controls and change the setting of the
door mirrors, these new settings are saved in
the remote control. The next time you unlock
the car with the same remote control and
open the driver's door within five minutes, the
mirrors will assume their stored positions.
Laminated side windows*
The laminated windows in the front and rear
doors improve sound insulation in the passenger compartment and provide better protection against unauthorised entry.
02 Instruments and controls
Windows, rearview and door mirrors
Water and dirt-repellent coating on
the front side windows*
02
Side windows treated with the water
and dirt-repellent coating are marked
with a small symbol. For information on glass
care, see page 200.
IMPORTANT
Do not use a metal ice scraper to remove
ice from the windows. The water and dirtrepellent coating could be damaged.
* Option/accessory, for more information, see Introduction.
83
02 Instruments and controls
Power sunroof*
Open positions
WARNING
If there are children in the car:
02
Switch off the supply to the power sunroof
by removing the remote control key if the
driver leaves the car.
Ventilation position
Open:
–
Press the rear edge of the control (E)
upward.
Close:
–
Pull the rear edge of the control (F) downward.
Switch from ventilation position to comfort
position; pull the control rearward to its end
position (D) and release.
G007503
Automatic operation
Move the control over the resistance point
position (C) to the rearmost end position (D)
or over the resistance point position (B) to the
front end position (A) and release. The sunroof will open to the comfort position or will
close completely.
The sunroof controls are located in the roof
panel. The sunroof can be opened in two
positions:
Ventilation position, up at the rear edge
Sliding position, backwards/forwards
The remote control key must be in position I
or II.
Closing, automatic
Opening, automatic
Opening, ventilation position
Closing, ventilation position
* Option/accessory, for more information, see Introduction.
–
Closing, manual
Opening, manual
84
In order to open from comfort position to
maximum opening:
Pull the control to the rear once more to
the end position (D) and release.
Manual operation
Open:
–
Pull the control rearward to the point of
resistance (C). The sunroof moves to
maximum open position as long as the
button is kept depressed.
02 Instruments and controls
Power sunroof*
Close:
–
Press the control forward to the point of
resistance (B). The sunroof moves to
closed position as long as the button is
kept depressed.
WARNING
The sunroof's pinch-protection function
only operates during automatic closing,
not manual.
the handle and slide the screen forward to
close it.
02
Pinch protection
The sunroof's pinch protection function is
activated if the hatch is blocked by an object.
If blocked, the sunroof will stop and automatically open to the previous position.
WARNING
The sunroof's pinch protection function
only operates during automatic closing,
not during manual closing.
Sunscreen
G020157
Make sure that nobody is in danger of
becoming trapped in any way when closing the sunroof.
The sunroof features a manual, sliding interior
sunscreen. The sunscreen slides back automatically when the sunroof is opened. Grip
* Option/accessory, for more information, see Introduction.
85
General information on climate control................................................... 88
Electronic Climate Control, ECC............................................................. 91
Fuel-driven parking heater*..................................................................... 94
86
* Option/accessory, for more information, see Introduction.
CLIMATE CONTROL
03 Climate control
General information on climate control
03
Air conditioning
Ice and snow
The climate control system cools or heats as
well as dehumidifies the air in the passenger
compartment. The car is equipped with electronic climate control (ECC).
Remove ice and snow from the climate control air intake (the grille between the bonnet
and the windscreen).
NOTE
The air conditioning can be switched off,
but to ensure the best possible air in the
passenger compartment and prevent the
windows from misting, it should always be
on.
Misting windows
Reduce the problem of windows misting up
on the inside by cleaning the windows. Use a
regular window cleaner.
Multi-filter
Make sure that the multi-filter/pollen filter is
replaced regularly. Volvo recommends you
consult an authorised Volvo workshop.
88
Ventilation fan function
When the engine is off (and if the remote control key is in position I or II), the ventilation fan
is automatically switched off. This is to prevent the battery from becoming discharged.
NOTE
Do not cover or block the sensors with
clothing or other objects.
Side windows and sunroof
To ensure that the air conditioning works satisfactorily, close all side windows and the
sunroof (if fitted).
Acceleration
To activate the ventilation fan, turn the fan
control and set the desired speed.
The air conditioning system switches off temporarily at full throttle. You may briefly feel a
temporary rise in temperature.
ECC (electronic climate control)
Condensation
Actual temperature
The temperature you select corresponds to
the physical experience with reference to factors such as air speed, humidity and solar
radiation etc. in and around the car.
Sensor location
•
The sun sensor is on the top side of the
dashboard.
•
The temperature sensor for the passenger compartment is behind the climate
control panel.
In warm weather, condensation from the air
conditioning may drip under the car. This is
normal.
To ventilate the climate system's control system the ventilation fan can be started up to
50 minutes after the car's ignition has been
switched off. The fan is then switched off
automatically after approx. 15 minutes.
Fuel economy
With ECC, the air conditioning system is controlled automatically and is used just enough
to cool the passenger compartment and to
adequately dehumidify the incoming air. This
provides better fuel economy compared to
03 Climate control
General information on climate control
conventional systems where the air conditioning cools the air to just above freezing point.
Air vents in the dashboard
Panel vents in the door pillar
Air distribution
G028577
Incoming air is distributed through several different vents located throughout the car.
0
Open
Open
Closed
Closed
Lateral airflow
Lateral airflow
Vertical airflow.
Vertical airflow.
1. Aim the outer vents towards the side windows to remove misting from the front
side windows.
2. In cold climates: close the centre vents
for the most comfortable climate and best
demisting.
G027064
G027043
03
1. Aim the outer vents toward the rear side
windows to remove misting.
2. Aim the vents inwards for a comfortable
climate in the rear seat.
Bear in mind that small children can be sensitive to airflow and draughts.
}}
89
03 Climate control
General information on climate control
Ventilated front seats (Executive)
To increase the ventilation in steps:
–
Press briefly on
.
Seat heating, outer rear seats
(Executive)
To obtain maximum ventilation:
–
Hold
depressed for about 2 seconds.
To decrease the ventilation in steps:
03
–
Press briefly on
.
To switch off the ventilation:
Control for front seat ventilation.
The ventilation system consists of fans in the
seat and backrest that draw air through the
seat upholstery. The cooling effect increases
the cooler the passenger compartment air
becomes.
The ventilation is regulated from a control on
the control panel on the side of the front
seats which has three steps for the fan
speed.
To start seat ventilation:
–
90
Press briefly on
.
Hold
depressed for about 2 seconds.
The ventilation can be used at the same time
as front seat heating. For example, the function can be used to dry damp from clothing.
The ventilation system can be activated when
the engine is running.
NOTE
The seat ventilation should be used carefully by people sensitive to draughts. Comfort level I is recommended for long-term
use.
IMPORTANT
Seat ventilation cannot be started when
the passenger compartment temperature
is below 5 °C. This is in order to avoid
cooling down the seat occupant.
G030976
G030244
–
Button for rear seat heating, On/Off.
The seat heating in the rear seats is controlled with a button control in accordance
with the illustration above. There is one control on each side of the rear centre console
for each respective rear seat.
To start seat heating:
–
Press the button.
> The symbol in the button illuminates.
To stop the heating:
–
Press the button.
> The lamp goes out.
03 Climate control
Electronic Climate Control, ECC
Control panel
03
AC – On/off (ON/OFF)
Temperature, right-hand side
Recirculation/Multifilter with sensor*
Temperature, left-hand side
Recirculation
Fan
AUTO
Fan, rear passenger compartment*
Air distribution
Functions
Passenger compartment temperature
sensor
1. AC – ON/OFF
Defroster, windscreen and side windows
Rear window and door mirror defrosters
Heated front seats
cally (can be switched off using the AC button).
2. Air quality system, recirculation/
multifilter*
ON: The air conditioning is on. It is controlled
by the system's AUTO function. This way,
incoming air is cooled and dehumidified.
OFF: When the defroster function is activated
the air conditioning is switched on automati-
Certain cars are equipped with a "Multifilter"
and air quality sensor. The Multifilter separates gases and particles, thus reducing the
volume of odours and pollutants. The air
quality sensor detects increased levels of
contaminants in the outside air. When the air
quality sensor detects contaminated outside
air, the air intake is closed and the air in the
passenger compartment is recirculated. The
Multifilter also cleans the air recirculating in
the passenger compartment.
}}
* Option/accessory, for more information, see Introduction.
91
03 Climate control
Electronic Climate Control, ECC
A green light (AUT) illuminates
in the button when the air
quality sensor is active.
•
•
03
Operation:
–
Press AUTO to activate the air quality
sensor (normal setting).
Or:
Select one of the following three functions by repeatedly pressing
:
•
The lamp for MAN illuminates. Recirculation is now activated.
•
No lamp illuminates. Recirculation is
not activated unless needed to cool in
a warm climate.
•
The lamp for AUT illuminates. Recirculation is now activated.
Keep the following in mind:
•
Make it a rule to have the air quality sensor activated at all times.
•
Recirculation is limited in cold weather to
avoid misting.
•
If misting occurs, you should deactivate
the air quality sensor.
If misting occurs, you can use the
defroster functions for the windscreen,
side windows and rear window.
Follow the Volvo service programme for
the recommended replacement interval of
the Multifilter. If the car is used in environments where more contaminants are
present, it may be necessary to change
the Multifilter more often.
3. Recirculation
Recirculation can be used to shut out bad air,
exhaust, etc. from the passenger compartment. The air in the passenger compartment
is recirculated, i.e. no outside air is taken into
the car when this function is activated.
If you allow the air in the car to recirculate,
there is a risk of icing and misting, especially
in winter.
The timer function (cars with Multifilter and air
quality sensor have no timer function) minimises the risk for ice, misting and bad air.
Activate the function as follows:
1. Press
for more than 3 seconds.
The lamp flashes for 5 seconds. The air
recirculates in the car for 3-12 minutes
depending on the outside temperature.
2. The timer function is activated each time
you press
92
.
To switch off the timer function:
–
Press
again for more than 3 seconds. The lamp illuminates for 5 seconds
to confirm your selection.
4. AUTO
The AUTO function automatically regulates
climate control and maintains the selected
temperature. The automatic function controls
heating, air conditioning, air quality sensor,
fan speed, recirculation and air distribution. If
you select one or more manual functions, the
other functions continue to be controlled
automatically. All manual settings are
switched off when AUTO is switched on.
5. Air distribution
•
When the top button is depressed, air is
directed to the windows
•
When the centre button is depressed, air
is directed to the head and body
•
When the lower button is depressed, air
is directed to the legs and feet
Press AUTO to return to automatic air distribution.
6. Passenger compartment temperature
sensor
The passenger compartment temperature
sensor monitors the temperature inside the
car.
03 Climate control
Electronic Climate Control, ECC
7. Defroster, windscreen and side
window
2. Press once more: Low heat – one lamp
illuminates.
13. Fan, rear passenger compartment
(option in cars seating seven)
Used to quickly remove misting and ice from
the windscreen and side windows. Air flows
to the windows at high fan speed. The light in
the defroster button illuminates when the
function is active.
3. Press once more: Heating switched off –
no lamps illuminate.
Fan speed can be increased or decreased by
turning the knob. This only applies if AC is
selected for both front and rear* passenger
compartment. The button for rear passenger
compartment is in the centre console switch
panel, see page 61.
The following also takes place in order to provide maximum dehumidification in the passenger compartment:
•
•
the air conditioning (AC) is automatically
engaged (can be switched off with the AC
button).
recirculation is automatically disengaged.
is
When the defroster function
switched off the climate control system
returns to the previous settings.
8. Rear window and door mirror
defrosters
Use this button to quickly remove misting and
ice from the rear window and door mirrors,
see page 63 for further information about this
function.
9. Heated front seats
To activate front seat heating:
1. Press once: High heat – both lamps illuminate.
Volvo recommends that an authorised Volvo
workshop adjusts the temperature.
10 and 11. Temperature selector
03
The two knobs can be used to set the temperature for the passenger and driver's sides
of the car.
NOTE
Heating or cooling cannot be hastened by
selecting a higher or lower temperature
than the actual desired temperature.
12. Fan
Turn the knob to increase or decrease fan
speed. If AUTO is selected then fan speed is
regulated automatically. The previously set
fan speed is disengaged.
NOTE
If the knob is turned anticlockwise and the
fan indicator in the display goes out, the
fan and the air conditioning are switched
off.
* Option/accessory, for more information, see Introduction.
93
03 Climate control
Fuel-driven parking heater*
General information about heaters
03
The parking heater can be started immediately or set with two different start times
using TIMER 1 and TIMER 2. Here, time
refers to the time when the car is heated and
ready. The car's electronic system calculates
when heating should be started based on the
outside temperature.
The heater is not run if the outside temperature exceeds 25 °C. At -10 °C and below, the
maximum running time of the parking heater
is 60 minutes.
If the parking heater does not start, despite
repeated attempts, Volvo recommends that
you contact an authorised Volvo workshop. A
message is shown in the display.
READ button
Thumbwheel
RESET button
The electrical system must be "awakened"
before the parking heater can be programmed.
This is done by:
•
•
•
pressing the READ button or
activating main beam or
turn the remote control key to key position I.
Warning label on fuel filler flap.
WARNING
The car must be outdoors when the parking heater is used.
Switch off the parking heater before refuelling. Fuel which spills out could be ignited.
Check in the display that the parking
heater is off. (When the parking heater is
running, PARK HEAT ON is shown in the
display.)
Messages in the display
Once the settings for TIMER 1, TIMER 2 and
Direct Start is activated are activated, the
amber warning symbol in the combined
94
* Option/accessory, for more information, see Introduction.
03 Climate control
Fuel-driven parking heater*
instrument panel illuminates and explanatory
text is shown in the display.
3. Scroll with the thumbwheel to the desired
hour.
When you leave the car, you will receive a
message regarding the current settings of the
system. The message disappears when the
car is locked from the outside using the
remote control key.
4. Briefly press RESET to move to the flashing minutes setting.
Parking on a hill
If you park your car on a steep incline, the
front of the car should be facing down the
slope to ensure the supply of fuel to the parking heater.
Clock/timer
If the car clock is reset after the heater timers
are programmed, the selected times will be
cancelled.
Setting the TIMER
For safety reasons, you can only programme
times for the following 24 hours, not several
days in advance.
1. Scroll using the thumbwheel until TIMER
1 or 2 is shown in the display.
5. Scroll with the thumbwheel to the desired
minute.
6. Briefly press RESET to confirm the setting.
7. Press RESET to activate the timer.
Deactivating timer-started parking
heater
Direct start
1. Scroll with the thumbwheel until DIRECT
START is shown in the display.
2. Press RESET to access the options ON
or OFF.
3. Select ON.
Immediate stop of heater
Proceed as follows to manually switch off the
parking heater before the set time has
elapsed:
1. Scroll with the thumbwheel until DIRECT
START is shown in the display.
1. Press READ.
2. Press RESET to access options ON or
OFF.
2. Use the thumbwheel to scroll to the text
PARK HEAT TIMER 1 or 2. The text ON
flashes on the display.
3. Press RESET. The text OFF is shown
with a constant glow and the parking
heater is switched OFF.
03
The heater will now run for 60 minutes. Heating of the passenger compartment will begin
as soon as the engine coolant has reached a
temperature of 30 °C.
3. Select OFF.
NOTE
The car can be started and driven while
the parking heater is still running.
2. Briefly press RESET so that the hours
setting starts to flash.
}}
* Option/accessory, for more information, see Introduction.
95
03 Climate control
Fuel-driven parking heater*
Battery and fuel
03
If the battery has insufficient charge or the
fuel level is too low, the parking heater will be
switched off automatically. A message is
shown in the display. Acknowledge the message by pressing READ once.
IMPORTANT
Repeated use of the parking heater combined with short journeys may discharge
the battery and impair starting. The car
should be driven for the same time as the
heater is used to ensure that the car's battery is recharged adequately to replace the
energy consumed by the heater when it is
used on a regular basis. The heater is used
for a maximum of 60 minutes each time.
Additional heater (diesel)*
Extra heat from the additional heater may be
required in cold weather to reach the correct
temperature in the passenger compartment.
The additional heater starts automatically
when extra heat is required if the engine is
running. It is switched off automatically when
the correct temperature is reached or when
the engine is switched off.
96
* Option/accessory, for more information, see Introduction.
03 Climate control
03
97
Front seats............................................................................................
Front seats - Executive ........................................................................
Interior lighting......................................................................................
Storage spaces in the passenger compartment...................................
Storage spaces in the passenger compartment - Executive ...............
Rear seat...............................................................................................
Loading.................................................................................................
Cargo area............................................................................................
98
100
103
104
106
111
112
114
115
INTERIOR
04 Interior
Front seats
Seating position
The passenger seat backrest can be folded
forward to make room for long loads.
Lumbar support1, turn the wheel.
Backrest rake: turn the wheel.
1. Move the seat as far back as possible.
Control panel for power seat*.
2. Adjust the backrest to an upright position
90 degrees.
WARNING
3. Lift the catches on the rear of the backrest while folding it forwards.
Adjust the position of the driver's seat
before setting off, never while driving.
4. Slide the seat forward so that the head
restraint is "locked in place" under the
glovebox.
Check that the seat is locked in position.
G027960
04
Raising takes place in reverse order.
Tipping the front seat backrest*
WARNING
Grasp the backrest and make sure that it
is properly locked after being folded up in
order to avoid personal injury in the event
of sudden braking or an accident.
The driver's and passenger seats can be
adjusted to the optimum sitting and driving
positions.
Raise/lower the front of the seat cushion,
pump up/down, (driver's and passenger
side*).
Raise/lower the seat, pump up/down,
(driver's and passenger side*).
1
100
Also applies to power seat.
* Option/accessory, for more information, see Introduction.
G014805
Forward/backward: lift the handle to
adjust the distance to the steering wheel
and pedals. Check that the seat is locked
after changing position.
04 Interior
Front seats
Inlay mats*
Volvo supplies inlay mats which are especially produced for your car.
WARNING
Before setting off check that the inlaid mat
in the driver area is firmly affixed and
secured in the bosses in order to avoid
getting caught adjacent to and under the
pedals.
The seats can be adjusted for a certain time
after unlocking the door with the remote control key without the key being inserted into
the ignition switch. The seat can always be
adjusted in ignition position I or II.
Memory function*
Front edge of seat cushion up/down
Seat forward/rearward
Seat up/down
Backrest rake
Power seat*
04
An overload protection is deployed if one of
the seats is blocked. If this happens, turn off
the ignition and wait a short time before
adjusting the seat again. Only one of the
seat's settings can be adjusted at a time.
Buttons for memory function.
Store setting
1. Adjust seat.
2. Press and hold button MEM while pressing button 1, 2 or 3 simultaneously.
Using a stored setting
Press one of the memory buttons 1–3 until
the seat stops. If you release the button then
the movement of the seat will stop.
}}
* Option/accessory, for more information, see Introduction.
101
04 Interior
Front seats
Key memory in remote control key
All remote control keys can be used by different drivers to store the settings for the driver's seat and door mirrors2. Proceed as follows:
•
•
Adjust the seat as you want it.
•
Unlock the car (by pressing the unlock
button on the same remote control key)
and open the driver's door. The driver's
seat and door mirrors will automatically
adopt the positions that are stored in the
remote control key's memory (if the seat
has been moved since you locked the
car).
04
Lock the car by pressing the lock button
on the remote control key that you normally use. This stores the positions of the
seat and door mirrors in the remote control key's memory3.
WARNING
Risk of crushing. Make sure that children
do not play with the controls.
Check that there are no objects in front of,
behind or under the seat during adjustment.
Ensure that none of the backseat passengers will be trapped.
Emergency stop
If the seat accidentally begins to move, press
one of the setting buttons for the seat or
memory buttons in order to stop the seat.
2
3
102
Only if the car is equipped with power seat with memory and retractable power door mirrors.
This setting does not affect settings that have been stored in the power seat's memory function.
04 Interior
Front seats - Executive
Comfort seats, front
Massage
Setting lumbar
Massage
Lumbar
Button for activating massage.
Hard massage
Soft massage
Each front seat has massage in the backrest.
The massage is performed by air cushions
that can massage with either a hard or soft
setting. When one of the settings is selected
the massage is carried out in accordance
with the cycle: massage 6 minutes - pause 4
minutes - massage 6 minutes etc.
When the button is in the centre position, or
when the remote control key is in position 0,
massage is not activated.
G030229
G030180
G030183
04
Button for setting lumbar.
The lumbar support is set with the same air
cushions used for massage. Adjustment can
be made steplessly both in terms of depth
and height using the control button, see the
illustration above.
Lumbar support can be set when massage is
not active.
A memory function recalls the lumbar setting
when massage is stopped or when the pressure in the air cushions has decreased, e.g.
after a longer period of parking.
103
04 Interior
Interior lighting
Reading lamps and interior lighting
well as when the engine is running. The lighting can also be activated within 10 minutes
after:
•
the engine has been switched off and the
ignition is in position 0
•
the car has been unlocked but the engine
has not been started
Rear roof lighting
Following which, it is switched off automatically.
Front roof lighting
The front reading lamps are switched on or
off by pressing the relevant button in the roof
console.
Controls in roof console for front reading lamps
and passenger compartment lighting.
Reading lamp left-hand front
Interior lighting
Reading lamp right-hand front
Passenger compartment lighting1 is switched
on with a short press on button (2), at the
same time automatic lighting is activated, see
page 105. Passenger compartment lighting is
switched off with a short press on button (2).
All lighting in the passenger compartment can
be switched on in ignition position I and II as
1
104
Courtesy lighting follows passenger compartment lighting.
* Option/accessory, for more information, see Introduction.
G027153
G026960
04
Rear reading lamps
Reading lamp left-hand rear, On/Off
Reading lamp right-hand rear, On/Off
The lamps are switched on or off by pressing
the relevant button.
There are also reading lamps for the third row
of seats in cars that seat seven.
Courtesy lighting
Courtesy lighting (and passenger compartment lighting) is switched on and off respectively when a side door is opened or closed.
04 Interior
Interior lighting
Cargo area lighting
The light illuminates automatically when the
cover is lifted.
The cargo area has a lamp on the inside of
the tailgate.
The rear lamp in the passenger compartment
and the lamp in the tailgate are switched on
and off respectively when the tailgate is
opened or closed.
Glovebox lighting
Glovebox lighting is switched on and off
respectively when the lid is opened or closed.
Vanity mirror*
The programmed times, 30 seconds and
10 minutes, can be changed by a Volvo workshop.
Automatic lighting
Automatic lighting can be disengaged by
pressing button (2), see page 104, and holding it depressed for more than 3 seconds. A
short press on the button re-engages automatic lighting.
When automatic lighting is activated the passenger compartment lighting is switched on
automatically2 and remains on for 30 seconds:
•
the car is unlocked with the key or remote
control key
•
the engine is switched off and the key is
turned to the 0 position.
04
Passenger compartment lighting is switched
on and remains on for 10 minutes if one of
the doors is open and the passenger compartment lighting is not switched off.
G027045
Passenger compartment lighting is switched
off when:
2
•
•
the engine is started
the car is locked with the key or remote
control key.
The function is light-dependent and is only activated when it is dark.
* Option/accessory, for more information, see Introduction.
105
04 Interior
Storage spaces in the passenger compartment
Storage spaces
04
106
04 Interior
Storage spaces in the passenger compartment
Storage compartment in third row of
seats
Pen holder
Glovebox
Storage compartment and cup holder
Ticket clip
Glovebox
Storage tray in centre console
ATTENTION
Cup holder for rear seat passengers
Pakjdskdl ioiuip kjöpp opoodidåuswi
AIRBAG
MY KEY
L E CTOR
SE
SOUND
Storage pocket (also on the front edge of
the front seat cushions)
ENTER
Ensure that no hard, sharp or heavy
objects lie or protrude in such a way that
they could cause injury during heavy braking.
The centre console contains a pen holder.
80
G027025
G027030
Bag holder
WARNING
04
EXIT
MENU
The glovebox can be used to store things
such as the owner's manual, maps, pens and
petrol cards.
Always secure large and heavy objects
with a seatbelt or cargo retaining straps.
}}
* Option/accessory, for more information, see Introduction.
107
04 Interior
Storage spaces in the passenger compartment
Coat hanger
Ashtray for rear seat passengers*
Cup holder/bottle holder for rear seat
passengers
The coat hanger is only intended for light garments.
Open the ashtray by pulling the top edge outward.
Pull the bottom edge of the insert to open.
To empty:
The cup holder insert can be removed:
1. Open the ashtray.
–
2. Press the cover outwards and tip it back.
3. Then lift it out.
108
G027063
G027018
G027028
04
* Option/accessory, for more information, see Introduction.
Detach the two clips so the holder can be
used for large bottles.
04 Interior
Storage spaces in the passenger compartment
Storage compartment and cup holder
(cars seating seven)
Storage tray in centre console
Cup holder
This storage compartment can be used for
CDs, books and the like.
The centre console contains a storage tray for
food and drinks, for example. The armrest
can be folded back to make a "table" for rear
seat passengers.
G027020
G027019
G027040
04
Cup holder for front seat passengers.
Ashtray*
–
Pull out the insert to empty the astray.
Under the storage tray is a storage compartment, e.g. for CD discs.
* Option/accessory, for more information, see Introduction.
109
04 Interior
Storage spaces in the passenger compartment
Storage compartment in the third row
of seats (cars seating seven)
G027026
04
This storage compartment can be used for
pens and other small items.
110
04 Interior
Storage spaces in the passenger compartment - Executive
Cooler box
G027068
04
There is a cooler box under front seat's folding armrest. Adjust the cooling level with the
button (see illustration). The cooler box works
when the engine is running or in key position
II.
WARNING
Store bottles well sealed in the cooler box
and make sure that the door is closed for
the journey.
111
04 Interior
Rear seat
Rear seats – second row (cars seating
seven)
Sliding seat (cars seating seven)
Removing the rear section of the
centre console
G028445
04
Lowering the backrest for entry into the
car
Lift the handle (1) up while pushing the seat
forward. Do the reverse to return the seat to
its original position.
Adjusting the seat front - rear
Lift the bracket (2) to move the seat forwards
or backwards.
112
The centre seat in the second row can be slid
farther forward than the other seats. Sliding
the seat completely forward improves contact
between a child sitting on the integrated
booster cushion and front seat occupants.
Lift the bracket (1) to move the seat forwards
or backwards.
The centre console must first be removed if
you wish to slide the centre seat in the second row forward.
1. Remove the rear section of the centre
console by pulling the catch straight out
as illustrated above.
2. Then lift the console out of the way.
04 Interior
Rear seat
Head restraint, rear seat – centre seat
WARNING
The lowest position should only be used
when the backrest is to be folded down or
when no one is sitting in this seat.
After raising the backrests in the second
and third row, it is important to make sure
that the backrests have locked into position. Otherwise the protective system of
the seats may be compromised.
G027015
NOTE
04
The head restraint cannot be removed
completely.
The centre seat head restraint can be
adjusted to four different heights. Raise the
head restraint as necessary.
–
To lower the head restraint again, the button by the right-hand shaft must be
pressed in while the head restraint is
pressed down carefully. See illustration.
113
04 Interior
Loading
General
•
Payload depends on the car's kerb weight.
The total of the weight of the passengers and
all accessories reduces the car's payload by
a corresponding weight. For more detailed
information on weights, see page 288.
The size of the area exposed to the wind,
and therefore fuel consumption, increase
with the load's size.
•
Drive gently. Avoid quick acceleration,
heavy braking and hard cornering.
WARNING
The car's driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
04
Load on the roof
Load carriers
Load carriers designed by Volvo are recommended in order to avoid damaging the car
and for maximum possible safety while driving.
Carefully follow the mounting instructions
enclosed with the load carriers.
114
•
Check periodically that the load carriers
and load are properly secured. Lash the
load securely with retaining straps.
•
Distribute the load evenly over the load
carriers. Put the heaviest objects at the
bottom.
WARNING
Load no more than 100 kg on the roof,
inclusive of the load carriers or space box.
The car's centre of gravity and driving characteristics are altered by roof loads.
04 Interior
Cargo area
Extension, cargo area - seat row 2
3. Release the catch (1) and fold down the
backrest. Press down to lock the backrest in its folded position.
IMPORTANT
There must be no objects on the rear seat
when the backrest is to be folded down.
The seat belts must not be connected
either. Otherwise there is a risk of damaging the rear seat upholstery.
IMPORTANT
WARNING
For reasons of safety, no passengers
should sit in the third row of seats if the
outer head restraints in the second row are
lowered.
There must be no objects on the rear seat
when the backrest is to be folded down.
The seat belts must not be connected
either. Otherwise there is a risk of damaging the rear seat upholstery.
Push the second row of seats to its front
position - see page 100.
Lift the handle upward.
Extension, cargo area - seat row 31
04
Slide the seat cushion to its rearmost
position. Fold in the right and left-hand
cargo eyes in order to avoid damage
when lowering the backrest.
Fold down the backrest. (The head
restraint folds in automatically when the
backrest is folded.)
Resetting seat row 3
1. Set the seats in their rearmost positions1.
2. Lower the head restraint.
1
Only cars seating seven
G027016
G027022
1. Raise the backrest to its normal position.
2. Take hold of the eyes and pull out the
seat cushion until a "click" sounds.
3. Raise the head restraint.
> The seat is now ready for use.
}}
115
04 Interior
Cargo area
General
Bear in mind that if an object weighing 20 kg
is subjected to a frontal collision at a speed of
50 km/h, its impact weight will be 1000 kg.
Opening the tailgate
For information about how the tailgate is
opened - see page 128.
Think about the following when loading:
Loading the cargo area
G027031
04
The seatbelts and airbags provide the driver
and passengers substantial protection, especially in frontal collisions. However, you must
also remember to protect yourself against
injuries from behind. When loading cargo,
bear in mind that improperly secured or incorrectly loaded objects in the cargo area could
be thrown forward with great speed and force
in the event of a collision or sudden braking,
causing serious injuries.
116
•
Do not load extremely heavy objects up
by the front seats. The lowered backrest
will be pressed down unnecessarily hard.
•
•
•
Place the load by the backrest.
Position heavy loads as low as possible.
Position wide loads on each side of the
division in the backrest.
•
•
Cover sharp edges with something soft.
•
Never load above the backrest without a
load net.
Secure the load with retaining straps
using the car's lashing eyes.
WARNING
The driving characteristics of the car
change based on the car's kerb weight
and how heavily it is loaded.
WARNING
Never load cargo above the backrests! If
you do so, the load could be thrown forward in the event of sudden braking or a
collision and severely injure you or your
passengers. Remember to always secure
(bind) the load properly.
If the rear seat backrest is lowered, do not
load the car higher than 50 mm under the
top edge of the rear passenger windows.
Leave 10 cm of free space from the windows inwards. Otherwise, the intended
protection of the inflatable curtain, which is
hidden in the headlining, may be compromised.
Always secure the load. Always secure the
load. During heavy braking the load may
otherwise shift, causing personal injury to
the car's occupants.
Turn off the engine and apply the parking
brake when loading or unloading long
objects! Otherwise you may accidentally
knock the gear lever or gear selector with
the load and cause a gear to engage and
the car to move off.
04 Interior
Cargo area
Safety net
Fitting the safety net
Only applies to cars seating seven:
1. Make sure the net lies in front of the side
panel armrest when securing.
2. Tension the safety net using the anchoring straps.
Folding up the safety net
G027058
04
The safety net prevents luggage and cargo
from being thrown forward in the passenger
compartment during heavy braking.
The net is made of a strong nylon fabric and
can be secured two different ways:
•
•
Behind the rear seat backrest
Behind the front seats if the rear seat is
lowered.
If the car is equipped with a cargo area cover,
remove it before fitting the safety net.
1. Hook the upper rod in the front or rear
roof mounting.
2. Hook the other end of the rod in the roof
mounting on the other side.
3. Secure the safety net anchoring straps in
the eyes on the floor if the net is secured
in the rear roof mountings.
4. Use the eyes in the seat slide rail if the
net is secured in the front roof mountings.
The safety net can be folded up and placed in
the cargo area floor (for cars seating five).
–
Press the buttons (1) in the safety net
hinges to release the hinges and fold up
the net.
}}
117
04 Interior
Cargo area
WARNING
It is necessary to ensure that the upper
securing points of the safety net are fitted
correctly and that the tensioning straps are
secured properly.
Damaged nets must not be used.
Steel safety grille*
For reasons of safety, the protective grille
must always be mounted and secured correctly.
4. Place the other protective grille mounting
in its bracket above the other rear door
and slide it to the front position.
Fit the protective grille as follows:
5. Insert the attaching brace through the
lower mounting in the protective grille
from underneath, as indicated in the illustration.
1. Lift in the protective grille through the tailgate opening or one of the rear doorways
(fold down the seats in the second row if
necessary).
2. Insert one of the protective grille mountings in its bracket above the rear door
behind the second row of seats.
04
6. Fit the spring on the attaching brace and
screw in the knob.
7. Fit the hook from the attaching brace in
the load securing eyelet and tighten the
knob until the attaching brace takes hold
in the load securing eyelet.
8. Do the same on the other side.
9. Tighten both attaching braces alternately.
10. Fit protective caps on the exposed screw
threads above the knobs.
The protective grille in the cargo area prevents cargo or pets from being thrown forward in the passenger compartment in the
event of heavy braking.
118
G027057
G027056
WARNING
3. Slide the protective grille mounting to the
front position of the bracket.
* Option/accessory, for more information, see Introduction.
For cars seating seven: For reasons of
safety, no passengers should sit in the
third row of seats if the protective grille is
positioned behind the second row of
seats.
04 Interior
Cargo area
Electrical socket in cargo area
NOTE
Remember that using the electrical socket
with the engine switched off involves the
risk of discharging the car's battery.
NOTE
The compressor for emergency puncture
repair is tested and approved by Volvo.
For information about using Volvo's recommended temporary mobility kit (TMK)
for emergency puncture repair, see
page 190.
Pull out the cargo area cover, pull it over the
cargo and hook it into the holes in the rear
pillars of the cargo area.
Removing the cargo area cover
Press the end pieces of the cargo area cover
inwards, pull up and release. When fitting,
press the end pieces of the cargo area cover
down into the holders.
WARNING
Do not place objects on the cargo area
cover. They could injure passengers during
braking or evasive manoeuvres.
04
Cargo cover*
Slide down the cover when you wish to use
the socket. It works regardless of whether the
ignition is on or off.
Bag holder*
If the ignition is switched off and a power
consumer that uses more than 0.1 A is connected to the electric socket, a warning message is shown in the display.
IMPORTANT
Max. power takeoff is 10 A (120 W).
}}
* Option/accessory, for more information, see Introduction.
119
04 Interior
Cargo area
Open the hatch in the cargo area. Hang or
secure your grocery bags using the tensioning straps or holders.
NOTE
Some components of the first-aid kit have
an expiration date and should be replaced
before this date.
Cargo area compartment, contents
Opening the compartment in the cargo
area floor (cars seating five)
–
Lift up the cover in the cargo area floor.
If the car is equipped with a carrier bag
holder:
04
–
Lift the cover, detach the tensioning
straps to the grocery bag holder.
Opening the compartment in the cargo
area floor (cars seating seven)
–
Location of first aid kit in cars seating
five.
Lift up the cover.
If the car is equipped with a carrier bag
holder:
–
Open the upper cover, detach the tensioning straps to the grocery bag holder,
if fitted, and open the lower cover.
Location of first aid kit in cars seating
seven.
The following is housed in the floor compartment:
•
•
•
•
120
Warning triangle*
Tool kit
IMPORTANT
Remember not to put anything in the area
that the cushions fold into. The cushions
and seat mechanisms could be damaged.
First aid kit*
Jack (alternative location)
* Option/accessory, for more information, see Introduction.
04 Interior
04
121
Remote control key - key with remote control......................................
Locking and unlocking..........................................................................
Child safety locks..................................................................................
Alarm*....................................................................................................
122
* Option/accessory, for more information, see Introduction.
124
126
130
131
LOCKS AND ALARM
05 Locks and alarm
Remote control key - key with remote control
Keys – Electronic immobiliser
Immobiliser
Remote control functions
The keys are fitted with coded chips. The
code must be accepted by the reader
(receiver) in the ignition switch. The car can
only be started if the correct key with the correct code is used.
NOTE
G027013
The key blade on the remote control key
must be fully extended (as illustrated)
when starting the car. Otherwise there is a
risk that the immobiliser function will prevent the car from starting.
Remote control key. This key opens all locks.
05
The car is supplied with two remote control
keys - they are collapsible and equipped with
built on remote control.
Loss of key
If you should lose one of your remote control
keys, you are recommended to bring the
remaining keys to an authorised Volvo workshop. The code of the missing key must be
erased from the system as a theft prevention
measure. The other keys must be re-coded in
the system at the same time.
Ignition keys and electronic immobiliser
The remote control key must not hang with
other keys or metal objects on the same key
ring. The electronic immobiliser could be activated erroneously and the car will not start.
The key blade's unique code is provided by
authorised Volvo workshops, which are recommended when ordering new key blades.
A maximum of six remote control keys can be
programmed and used for one single car.
124
* Option/accessory, for more information, see Introduction.
Unlocking
–
Press the button once to unlock all doors,
the tailgate and the fuel filler flap simultaneously.
Tailgate
–
Press the button once to unlock the tailgate.
Panic function
Panic function - Can be used to attract attention in an emergency. Press and hold the red
button for at least 3 seconds or press it 2
times within the same space of time to activate the direction indicators and the horn.
05 Locks and alarm
Remote control key - key with remote control
The panic alarm is deactivated automatically
after 25 seconds or by pressing any of the
buttons on the remote control key.
Approach light duration
Do the following when you approach the car:
–
Press the yellow button on the remote
control key.
The interior lighting, position/parking lamps,
number plate lighting, door mirror lamps* will
now switch on. The lighting on a coupled
trailer will also switch on. These lamps remain
lit for 30, 60 or 90 seconds. A suitable time
setting can be made at a workshop - an
authorised Volvo workshop is recommended.
Replacing the remote control key's
battery
1. Remove the cover by carefully prising up
the rear edge of with a small screwdriver.
NOTE
Volvo recommends that the batteries to be
used in the remote control key/PCC fulfil
UN Manual of Test and Criteria, Part III,
sub-section 38.3. Batteries fitted in the
factory or replaced by an authorised Volvo
workshop fulfil the above criteria.
2. Replace the battery (type CR 2032, 3 V) –
with the plus side facing up. Avoid touching the battery and its terminals with your
fingers.
3. Refit the cover. Make sure the rubber seal
is properly fitted and free from damage to
prevent water from entering.
4. Return the old battery to your Volvo workshop so that it is disposed of in an environmentally safe manner.
05
To extinguish the approach lighting:
–
Press the yellow button again.
Locking
Lock all doors, tailgate and fuel filler flap with
the button. There is a delay of approx.
10 minutes for the fuel filler flap.
Folding/opening key
The remote control key can be folded by
pressing the button and folding the key blade
section into the keypad at the same time.
The folding key will open automatically with
one press of the button.
Replace the battery after repeated failure by
the locks to respond when remote control key
signals are transmitted within a normal distance.
* Option/accessory, for more information, see Introduction.
125
05 Locks and alarm
Locking and unlocking
From the outside
NOTE
Automatic locking
The car can be locked even if a door or the
tailgate is open1 - when the door/tailgate is
then closed there is a risk that the keys will
be locked in.
G029646
G026963
WARNING
Be aware of the risk of being locked in the
car when it is locked from the outside
using the remote control key - it is then not
possible to open any of the doors from the
inside with the door controls. Read more
about this in the section "Deadlocks" later
on.
05
The remote control key locks/unlocks all
doors and the tailgate simultaneously.
The fuel filler flap can be opened when the
car is unlocked. It remains unlocked for 10
minutes after the car has been locked - this is
in order to enable refuelling with the car
locked and the alarm armed.
Automatic relocking
If none of the doors or the tailgate is opened
within 2 minutes of unlocking with the remote
control key then all are locked again automatically. This function prevents the car from
being left unlocked unintentionally.
For cars with alarms, see page 131.
Automatic locking is activated and deactivated from the driver's door control panel.
The function operates by locking the doors
automatically when the speed of the car
exceeds 7 km/h. They remain locked until a
door is opened from the inside or when all
doors are unlocked from the control panel.
Activation/Deactivation
The remote control key must be in key position I or II, see page 145.
1
126
Not in all markets.
05 Locks and alarm
Locking and unlocking
•
Press the left-hand stalk switch READ
button to acknowledge any messages on
the display.
All doors can be locked using the lock button
on the control panel by each respective door.
•
Press and hold the button for central
locking until a new message for lock status is shown in the display.
Glovebox
Tailgate
The messages AUTOLOCK ON (the car is
also locked when it moves) and AUTOLOCK
OFF respectively are shown on the display.
From the inside
AIRBAG
G028485
ATTENTION
Pakjdskdl ioiuip kjöpp opoodidåuswi
MY KEY
L E CTOR
SE
SOUND
ENTER
EXIT
05
G027025
MENU
The alarm for the tailgate can be disarmed
and the tailgate unlocked on its own by using
the remote control key.
The glovebox can be locked with the remote
control key's key blade.
1. Press the remote control key's
button - the tailgate is unlocked and can
then be opened.
> The alarm's* level and movement sensors and the sensor for opening the
tailgate are disconnected. The doors
continue to remain locked and their
alarms armed.
G029646
80
All the doors and the tailgate can be locked
or unlocked simultaneously using the control
panel in the driver's door (or passenger door).
}}
* Option/accessory, for more information, see Introduction.
127
05 Locks and alarm
Locking and unlocking
2. If all doors continue to be locked when
you re-close the tailgate, the tailgate
remains unlocked and its alarm is not
armed after being closed. The other
doors continue to remain locked with
their alarms armed.
Deadlocks*2
Opening the tailgate
Deadlocks means that the opening handles
for the doors in the passenger compartment
are mechanically disengaged - the doors cannot therefore be opened from the inside.
The deadlocks function is activated from the
outside with the remote control key's LOCK
button, or by locking the driver's door with
the key blade, and is set after a 10-25 second
delay after the doors have been locked. All
doors must be closed before deadlocks can
be activated.
3. To lock the tailgate and arm the alarm as
well - press the remote control key's
LOCK button.
NOTE
05
G027005
If the
button is used to unlock the tailgate without it being opened then it is
relocked automatically after about 2
minutes.
1. Open the tailgate by pulling down its handle as illustrated.
2. The rear flap is folded down when its handle is lifted up.
2
128
Not in all markets and only in combination with alarm.
* Option/accessory, for more information, see Introduction.
The car can only be unlocked from a deadlock state with the remote control key's
UNLOCK button. The driver's door can also
be unlocked manually with the key blade.
WARNING
Do not allow anyone to remain in the car
without first deactivating the deadlocks in
order to avoid the risk of anyone being
locked in.
05 Locks and alarm
Locking and unlocking
Temporary deactivation
message is shown on the display as long as
the remote control key remains in the ignition
switch.
Next time the engine is started the system is
reset to zero and the deadlocks function and
the alarm's movement and tilt detectors are
then re-engaged.
G027230
NOTE
•
Remember that the alarm is activated
when the car is locked.
•
If any of the doors are opened from
the inside then the alarm is triggered.
05
Button for temporary disengagement of deadlocks.
If someone is going to stay in the car but the
doors must be locked from the outside, then
the deadlocks function can be temporarily
switched off.
1. Insert the remote control key into the ignition switch, turn it to key position II and
then back to position I or 0.
2. Press the button. Note that the alarm's*
movement and tilt detectors are switched
off at the same time, see page 132.
The lamp in the button illuminates until the
car is locked with the remote control key. A
* Option/accessory, for more information, see Introduction.
129
05 Locks and alarm
Child safety locks
Manual child safety locks – rear doors
The controls for the child safety locks are
located in the rear edge of the rear doors. The
controls are only accessible when the rear
doors are open.
Controls
Child-safe position – the rear doors cannot be opened from inside: Turn outwards.
When the light in the button illuminates, the
rear power windows and rear doors are
locked.
Not child-safe position – the rear doors
can be opened from inside: Turn inwards.
A message appears on the display, the child
safety locks are activated/deactivated.
Electric child safety locks – rear side
doors*
REAR
AC
G027105
G021513
05
Controls for the child safety locks – left and righthand rear doors.
Adjust the control in the respective rear door
by turning it between the outer positions (use
a flat metal object, such as a screwdriver).
Use the button in the centre console to activate/deactivate the child safety locks in the
rear doors.
1. Turn the ignition key to position I or II,
see page 145.
2. Press the button.
130
* Option/accessory, for more information, see Introduction.
NOTE
As long as the child safety lock is activated
the rear doors cannot be opened from the
inside.
05 Locks and alarm
Alarm*
Alarm system
Alarm indicator
NOTE
When the alarm is armed, it continually monitors all alarm inputs.
Do not attempt to repair or modify alarm
system components. All such attempts
could affect the terms of insurance.
The alarm is triggered if:
•
•
a door, the bonnet or tailgate opens
•
a movement is detected in the passenger
compartment (if fitted with a movement
detector)
•
the car is raised or towed away (if fitted
with a tilt detector)
–
a battery cable is disconnected
The alarm is fully armed when the car's
direction indicators have made one long
flash and the LED on the instrument panel
flashes once every other second.
anyone tries to disconnect the siren.
NOTE
The movement sensors trigger an alarm in
the event of movement in the passenger
compartment - air currents are also registered. For this reason the alarm is triggered if the car is left with a window or the
sunroof open or if the passenger compartment heater is used.
To avoid this: Close the window/sunroof
when leaving the car. If the car's integrated passenger compartment heater (or
a portable electric heater) shall be used direct the airflow from the air vents so that
they are not pointing upwards in the passenger compartment.
A red LED on the instrument panel indicates
the alarm system's status:
•
•
LED not lit – the alarm is not armed.
•
The LED flashes rapidly after disarming
the alarm and until the remote control key
is turned to key position II – the alarm has
been triggered.
The LED flashes once every other second
– Alarm is armed.
If there is a fault in the alarm system, a message appears on the display. In which case,
contact a workshop - an authorised Volvo
workshop is recommended.
Press the remote control key's LOCK
button. A long flash from the car's direction indicators confirms that the alarm is
armed and that all the doors are locked.
IMPORTANT
G026963
•
•
Arming the alarm
a non-approved key is used in the ignition
or if an attempt is made to force the lock
05
Disarming the alarm
–
Press the remote control key's UNLOCK
button. Two short flashes from the car's
direction indicators confirm that the alarm
has been deactivated.
> For manual disarming - see the following section "Deactivating a triggered
alarm".
}}
* Option/accessory, for more information, see Introduction.
131
05 Locks and alarm
Alarm*
Automatic alarm activation
Remote control key not working
This function prevents you accidentally leaving the car without the alarm on.
If none of the doors or the tailgate is opened
within two minutes of disarming the alarm
(and the car has been unlocked with the
remote control key), the alarm is automatically rearmed. The car is locked at the same
time.
Automatic alarm activation
05
In certain countries the alarm is activated
after a certain delay if the driver's door was
opened and closed but the car was not relocked.
Deactivating a triggered alarm
–
Press the remote control key's UNLOCK
button or insert it into the ignition switch.
Confirmation is given by two short flashes
from the direction indicators.
132
If the alarm cannot be deactivated with the remote control key, e.g. if the key's battery is discharged - the car
can be unlocked, disarmed
and the engine started as follows:
1. Unlock the driver's door manually and
open it - The alarm is triggered and the
siren sounds.
2. Insert the remote control key in the ignition switch - The alarm is deactivated.
> The alarm indicator flashes rapidly until
the remote control key is turned to key
position II.
Alarm signals
When the alarm is triggered, the following
happens:
•
A siren sounds for 25 seconds or until the
alarm is switched off. The siren has its
own battery and works independently of
the car battery.
•
The direction indicators flash for
5 minutes or until the alarm is switched
off.
* Option/accessory, for more information, see Introduction.
Reduced alarm level
To avoid accidental triggering of the alarm e.g. if a dog is left in a locked car or during
transport on a car train or car ferry - temporarily deactivate the movement and tilt detectors.
The procedure is the same as with the temporary disengaging of deadlocks - see
page 128.
05 Locks and alarm
05
133
General..................................................................................................
Refuelling..............................................................................................
Starting the engine................................................................................
Automatic gearbox................................................................................
All-wheel drive*.....................................................................................
Brake system........................................................................................
Stability and traction control system*...................................................
Park assist syst*....................................................................................
Blind Spot Information System - BLIS*.................................................
Towing and recovery.............................................................................
Jump starting........................................................................................
Driving with a trailer..............................................................................
Towing equipment*...............................................................................
Detachable towbar*..............................................................................
Adjusting headlamp pattern..................................................................
134
* Option/accessory, for more information, see Introduction.
136
139
145
147
150
151
153
155
157
161
163
165
167
169
173
STARTING AND DRIVING
06 Starting and driving
General
Economical driving
Driving economically means driving smoothly
while thinking ahead and adjusting your driving style and speed to the prevailing conditions.
•
•
06
136
•
Avoid driving with open windows.
Do not use winter tyres when the winter
season is over.
•
Avoid sudden unnecessary acceleration
and heavy braking.
•
Drive with the correct air pressure in the
tyres and check this regularly - select
ECO tyre pressure for best results, see
page 183
•
Drive in the highest gear possible, adapted to the current traffic situation and
road - lower engine speeds result in lower
fuel consumption1.
•
Remove unnecessary items from the car the greater the load the higher the fuel
consumption.
•
Use engine braking to slow down, when it
can take place without risk to other road
users.
•
Choice of tyres can affect fuel consumption - seek advice on suitable tyres from a
dealer.
1
•
Manual gearbox
•
A roof load and ski box increase air resistance, leading to higher fuel consumption
- remove the load carriers when not in
use.
Do not run the engine to operating temperature at idling speed, but rather drive
with a light load as soon as possible - a
cold engine consumes more fuel than a
warm one.
High speed results in increased fuel consumption - doubling speed increases
wind resistance four times.
For more information and further advice, see
the pages 13 and 296.
WARNING
Never switch off the engine while moving,
such as downhill, this deactivates important systems such as the power steering
and brake servo.
Driving in water
The car can be driven through water at a
maximum depth of 40 cm at a maximum
speed of 10 km/h. Extra caution should be
exercised when passing through flowing
water.
IMPORTANT
Engine damage can occur if water enters
the air filter.
In greater depths, water can enter the
transmission. This reduces the lubricating
ability of the oils and shortens the service
life of the systems.
During driving in water, maintain a low speed
and do not stop the car. When the water has
been passed, depress the brake pedal lightly
and check that full brake function is achieved.
Water and mud for example can make the
brake linings wet resulting in delayed brake
function.
NOTE
Clean the electric contacts of the electric
engine block heater and trailer coupling
after driving in water and mud.
06 Starting and driving
General
IMPORTANT
Do not let the car stand with water over
the sills for any long period of time. This
could cause electrical malfunctions.
In the event of engine stop in water do not
try restart. Tow the car from the water.
Engine, gearbox and cooling system
Under special conditions, for example hard
driving in hilly terrain and hot climate, there is
a risk that the engine and drive system may
overheat - in particular with a heavy load.
•
Remove any auxiliary lamps from in front
of the grille when driving in hot climates.
•
In the event of a risk of overheating a
built-in protection function in the gearbox
is activated which, amongst other things,
illuminates the instrument panel's yellow
information lamp and there is a text message displayed there regarding appropriate action - follow the recommendation
given.
•
•
If the temperature gauge for the engine's
cooling system goes into the red zone stop and let the engine idle for a few
minutes.
If the car overheats, the air conditioning
may be switched off temporarily.
•
Do not turn the engine off immediately
you stop after a hard drive.
For supplementary information about overheating when driving with a trailer - see
page 165.
NOTE
It is normal for the engine's cooling fan to
operate for a while after the engine has
been switched off.
IMPORTANT
To prevent damage to any drive system
components, the working temperature of
the gearbox is checked. If there is a risk of
overheating, a warning symbol in the combined instrument lights up and a text message is shown. Follow the recommendation given in the text message.
Open tailgate
WARNING
Do not drive with the tailgate open. Toxic
exhaust fumes can be drawn into the car
through the cargo area.
Do not overload the battery
The electrical functions in the car load the
battery to varying degrees. Avoid having the
remote control key in key position II when the
engine is switched off. Instead use the I mode
- which uses less power.
Note that the 12 volt outlet in the cargo area
supplies power even when the remote control
key has been removed from the ignition
switch.
Also, be aware of different accessories that
load the electrical system. Do not use functions which use a lot of power when the
engine is switched off. Examples of such
functions are:
•
•
•
•
ventilation fan
windscreen wiper
audio system (high volume)
headlamps.
06
If the battery voltage is low the information
display shows the text LOW BATTERY
POWER SAVE MODE. The energy-saving
function then shuts down certain functions or
reduces certain functions such as the ventilation fan and/or audio system.
}}
137
06 Starting and driving
General
–
In which case, charge the battery by starting the engine and then running it for at
least 15 minutes - battery charging is
more effective during driving than running
the engine at idling speed while stationary.
Driving on rough roads
The Volvo XC90 is primarily designed for driving on main roads, but also has good handling properties on uneven or rough roads.
Keep the following in mind in order to preserve the service life of your car:
06
138
•
Drive slowly on rough roads - this avoids
damaging the car's underbody.
•
If the ground is loose or is made up of dry
sand or snow, it is always best to keep
the car moving at all times and avoid
shifting. Do not stop the car.
•
If the road is extremely steep and there is
a risk of overturning - never try to turn the
car around. Reverse back down instead.
•
Do not drive diagonally across an incline drive in the direction of the incline.
NOTE
Avoid driving on steep slopes if the fuel
level is low. The catalytic converter could
be damaged if the engine does not receive
enough fuel. When driving on extremely
steep slopes, make sure the tank is more
than half full to avoid the risk of breakdown.
Slippery driving conditions
Practise driving on slippery surfaces under
controlled conditions to learn how the car
reacts.
06 Starting and driving
Refuelling
Opening the fuel filler flap
Emergency unlocking of the fuel filler
flap
G027073
Manual unlocking of the fuel filler flap may be
necessary if it cannot be opened normally.
Proceed as follows:
The fuel filler cap is inside the fuel filler flap on
the right-hand rear wing and hangs up on the
inside of the fuel filler flap.
The fuel filler flap can be opened when the
car is unlocked.
06
NOTE
The filler flap remains unlocked for ten
minutes after the car is locked. It then
locks automatically.
}}
139
06 Starting and driving
Refuelling
Steps 1–3.
06
1. Lift up the corner piece from the floor in
the rear right-hand corner of the cargo
area.
4. Insert your hand and locate the lock. Its
location is approximately inside the rear
edge of the fuel filler flap.
2. Open the fuel filler flap by lifting up the
handle and pulling it out.
5. Carefully pull the lock plunger straight
back - the flap can then be folded out.
3. Fold aside the insulation in order to
access the flap's electrical lock.
After refuelling the flap can be relocked by
first closing it and then pushing the lock
plunger forward.
WARNING
There are sharp edges behind the panel so
move your hands slowly and carefully.
Steps 4–5.
140
06 Starting and driving
Refuelling
Fuel cap
A certain overpressure may arise in the tank
in the event of high outside temperatures.
Open the cap slowly
NOTE
Put the petrol cap back on after refuelling.
Turn until one or more clear clicks are
heard.
Filling with fuel
Do not overfill the tank but fill until the pump
nozzle cuts out.
NOTE
Excess fuel in the tank can overflow in hot
weather.
Fuel of a quality lower than that specified in
this chapter should not be used as engine
power and fuel consumption could otherwise
be negatively affected.
Make sure you insert the funnel's pipe firmly
into the filler pipe. The filler pipe has an openable cap and the funnel's pipe must be
moved past the cap before filling can begin.
General information on fuel
WARNING
Always avoid inhaling fuel vapour and getting fuel splashes in the eyes.
In the event of fuel in the eyes, remove any
contact lenses and rinse the eyes in plenty
of water for at least 15 minutes and seek
medical attention.
Never swallow fuel. Fuels such as petrol,
bioethanol and mixtures of them and diesel are highly toxic and could cause permanent injury or be fatal if swallowed.
Seek medical attention immediately if fuel
has been swallowed.
WARNING
Fuel which spills on to the ground can be
ignited by the exhaust fumes.
Switch off the fuel-driven heater before
starting to refuel.
Never carry an activated mobile phone
when refuelling. The ring signal could
cause spark build-up and ignite petrol
fumes, leading to fire and injury.
IMPORTANT
Mixing different types of fuel or the use of
fuel not recommended invalidates Volvo's
guarantees, and any associated service
agreement. This applies to all engines.
NOTE: It does not apply to cars with
engines that are adapted to run on ethanol
fuel (E85).
For detailed information on fuel consumption
and tank volume - see page 296.
06
Filling with a fuel can1
When filling with a fuel can, use the funnel
located under the floor hatch in the cargo
area. The funnel is located by the spare wheel
or in the well under the floor hatch.
1
Only applies to cars with diesel engine.
}}
141
06 Starting and driving
Refuelling
Petrol
Catalytic converter
Diesel
Petrol must fulfil the EN 228 standard. Most
engines can be run with octane ratings of 91,
95 and 98 RON.
The purpose of the catalytic converter is to
purify exhaust gases. It is located in the flow
of exhaust gases close to the engine so that it
quickly reaches operating temperature. The
catalytic converter consists of a monolith
(ceramic or metal) with channels. The channel
walls are lined with a thin layer of platinum/
rhodium/palladium. These metals act as catalysts, i.e. they participate in and accelerate a
chemical reaction without being used up
themselves.
Diesel must meet the EN 590 or JIS K2204
standards.
•
91 RON must not be used for 4-cylinder
engines and should only be used in
exceptional cases with other engines.
•
•
95 RON can be used for normal driving.
98 RON is recommended for optimum
performance and minimum fuel consumption.
When driving in temperatures above +38 °C,
fuel with the highest possible octane rating is
recommended for optimum performance and
fuel economy.
IMPORTANT
06
2
142
•
Always refuel with unleaded petrol so
as not to damage the catalytic converter.
•
Do not use additives not recommended by Volvo.
Lambda-sondTM oxygen sensor
The Lambda-sond is part of a control system
intended to reduce emissions and improve
fuel economy.
An oxygen sensor monitors the oxygen content of the exhaust gases leaving the engine.
This value is fed into an electronic system
that continuously controls the injectors. The
ratio of fuel to air directed to the engine is
continuously adjusted. These adjustments
create optimal conditions for efficient combustion of harmful emissions (hydrocarbons,
carbon monoxide and nitrous oxides) using
the three-way catalytic converter.
Diesel fuel may contain a certain amount of RME, but further amounts must not be added.
IMPORTANT
Only ever use fuel that fulfils the European
diesel standard.
IMPORTANT
Diesel type fuels which must not be used:
special additives, Marine Diesel Fuel, fuel
oil, RME2 (Rape Methyl Ester) and vegetable oil. These fuels do not fulfil the requirements in accordance with Volvo recommendations and generate increased wear
and engine damage that is not covered by
the Volvo warranty.
Diesel engines are sensitive to contaminants,
such as excessively high volumes of sulphur
particles for example. Only use diesel fuel
from well-known producers. Never use diesel
of dubious quality.
At low temperatures (-40 °C to -6 °C), a paraffin precipitate may form in the diesel fuel,
which may lead to ignition problems. Special
diesel fuel designed for low temperatures
around freezing point is available from the
06 Starting and driving
Refuelling
major oil companies. This fuel is less viscous
at low temperatures and reduces the risk of
paraffin precipitate.
IMPORTANT
Use special winter grade fuel during cold
months.
The risk of condensation in the fuel tank is
reduced if the tank is kept well filled. When
refuelling, check that the area around the fuel
filler pipe is clean. Avoid spilling fuel onto the
paintwork. Wash off any spillage with detergent and water.
IMPORTANT
The sulphur content must be a maximum
of 50 ppm.
Empty tank
The design of the fuel system in a diesel
engine means that if the vehicle runs out of
fuel, the tank may need to be vented in the
workshop in order to restart the engine after
fuelling.
Once the engine has stopped due to fuel
starvation, the fuel system needs a few
moments to carry out a check. Do this before
starting the engine, once the fuel tank has
been filled with diesel:
1. Insert the remote control key in the ignition switch and turn to key position II (see
page 145).
2. Wait approx. 1 minute.
3. To start the engine: Depress the brake
and/or clutch pedal, and turn the remote
control key to start position III.
Draining condensation from the fuel
filter
The fuel filter separates condensation from
the fuel. Condensation can disrupt engine
operation.
The fuel filter must be drained at the intervals
specified in the Service and Warranty Booklet
or if you suspect that the car has been filled
with contaminated fuel.
IMPORTANT
Certain special additives remove the water
separation in the fuel filter.
Diesel particle filter (DPF)
Diesel cars may be equipped with a particle
filter, which results in more efficient emission
control. The particles in the exhaust gases
are collected in the filter during normal driving. So-called "regeneration" is started in
order to burn away the particles and empty
the filter. This requires the engine to have
reached normal operating temperature.
Regeneration of the filter takes place automatically and normally takes 10-20 minutes. It
may take a little longer at a low average
speed. Fuel consumption may increase
slightly during regeneration.
The rear window heating may be activated
automatically to increase the load on the
engine during regeneration without warning.
Regeneration in cold weather
If the car is frequently driven short distances
in cold weather then the engine does not
reach normal operating temperature. This
means that regeneration of the diesel particle
filter does not take place and the filter is not
emptied.
When the filter has become
approximately 80% full of particles, the yellow information symbol on the instrument
panel illuminates, and the message SOOT
FILTER FULL SEE MANUAL is shown on
the instrument panel display.
06
Start regeneration of the filter by driving the
car until the engine reaches normal operating
temperature, preferably on a main road or
motorway. The car should then be driven for
approximately ca 20 minutes more.
}}
143
06 Starting and driving
Refuelling
NOTE
The following may arise during regeneration:
•
a smaller reduction of engine power
may be noticed temporarily
•
fuel consumption may increase temporarily
•
a smell of burning may arise.
When regeneration is complete the message
is cleared automatically.
Use the parking heater* in cold weather so
that the engine reaches normal operating
temperature more quickly.
IMPORTANT
06
144
If the filter fills up it may be incapable of
functioning. Then it can be difficult to start
the engine and there is a risk that the filter
will have to be replaced.
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Starting the engine
Before starting the engine
–
Starting the engine
Apply the parking brake.
IMPORTANT
Automatic gearbox
–
If the engine fails to start after 3 attempts wait for 3 minutes before making a further
attempt. Starting capacity increases if the
battery is allowed to recover.
Gear selector in position P or N.
WARNING
Never remove the remote control key from
the ignition switch while driving or when
the car is being towed. The steering lock
could otherwise be activated, making it
impossible to steer the car.
The remote control key must be in key
position II when the car is being towed.
Petrol
–
Turn the remote control key to key position III. If the engine does not start within
5–10 seconds, release the key and try
again.
Diesel
NOTE
The remote control key's key blade must
be fully extended when starting the car,
see page 124. Otherwise there is a risk
that the immobiliser function will prevent
the car from starting.
NOTE
1. Turn the remote control key to key position II.
An indicator symbol in the combined
instrument panel shows that engine preheating is underway, see page 59.
2. Turn the ignition key to position III when
the indicator symbol goes out.
> The starter motor is activated.
Ignition switch and steering lock
0 – Locked position
The steering lock is activated
when the remote control key
is removed from the ignition
switch.
I – Radio position
Steering lock deactivated.
Certain functions can be
used. The engine's electrical
system is not activated.
II – Driving position
The remote control key's
position when driving. The
whole electrical system is
engaged.
06
The idling speed can be noticeably higher
than normal for certain engine types during
cold starting. This is in order that the emissions system can reach normal operating
temperature as quickly as possible, which
minimises exhaust emissions and protects
the environment.
}}
145
06 Starting and driving
Starting the engine
III – Start position
The starter motor is activated. The remote control
key is released when the
engine has started and then
springs back automatically to
drive position.
If the key is hard to turn, the front wheels may
be turned in such a way that there is tension
in the steering wheel lock. In which case, turn
the wheel back and forth to make it easier to
turn the key.
Autostart (3.2)
Using the autostart function, the remote control key does not need to be kept in key position III until the engine has started.
•
06
Turn the key to the start position and then
release it - the starter motor then operates automatically (up to 10 seconds)
until the engine has started.
NOTE
Make sure the steering wheel locks when
you leave the car. This reduces the risk of
theft.
146
Remote control keys and electronic
immobiliser
The remote control key must not hang with
other keys or metal objects on the same key
ring. The electronic immobiliser could be activated accidentally.
Never rev up the engine hard immediately
after a cold start!
If the engine does not start or misfires, contact a workshop - a Volvo workshop is recommended.
WARNING
You must never turn the remote control
key to key position I or 0 and never
remove the remote control key from the
ignition switch while the car is moving. The
steering lock could otherwise be activated,
making it impossible to steer the car.
Always remove the remote control key
from the ignition switch when leaving the
car – especially if children are left alone in
the car.
06 Starting and driving
Automatic gearbox
Gear positions
The gearbox is mechanically blocked when
the P position is engaged. Always apply the
parking brake when parking the car.
Gear selector inhibitor
R – Reverse
The car must be stationary when position R is
selected.
N – Neutral
P – Parking position
Select position P when you wish to start the
engine or park the car.
IMPORTANT
The car must be stationary when position
P is selected.
G020237
G027997
N is the neutral position. No gear is engaged
and the engine can be started. Apply the
parking brake when the car is stationary with
the gear selector in position N.
D – Drive
D is the normal driving position. The car automatically shifts between the different gears of
the gearbox based on the level of acceleration and speed. The car must be stationary
when the gear selector is moved to position D
from position R.
The gear selector can always be moved freely
between N and D. Other positions are locked
with a latch that is released with the inhibitor
button on the gear selector.
06
With one press on the inhibitor button you
can move the lever forwards or backwards
between the gear positions, N, R and P.
NOTE
The brake pedal must be depressed to
move the gear lever from the P position.
}}
147
06 Starting and driving
Automatic gearbox
Manual positions
While driving
Cold start
The manual gearshift mode can be selected
at any time while driving. The engaged gear is
locked until you choose another gear.
When starting in low temperatures, the gear
changes can sometimes feel hard. This is due
to the gearbox oil's viscosity at low temperatures. To reduce engine emissions, the gearbox shifts up later than normal when the
engine is started at low temperatures.
If the gear selector is moved to – (minus) the
car changes down a gear and engine brakes
at the same time as the accelerator pedal is
released. If the gear selector is moved to +
(plus) the car changes up a gear.
G026990
Third gear 3 is the highest gear that can be
used when starting.
06
To move from the automatic driving position
D to a manual position, move the gear selector to position M. To go from position M to
the automatic driving position D, move the
selector to position D.
On the 5-speed automatic gearbox, gears 3,
4 and 51 have the Lock-up function (locked
gears), which provides better engine braking
and lower fuel consumption.
1
148
W – Winter
is active.
Press the W button to activate
and deactivate the winter program. Display of the W symbol in
the combined instrument panel
indicates that the winter program
The winter programme starts the gearbox in
3rd gear to make it easier to pull off on slippery roads. When the programme is engaged,
lower gears are activated only by kick-down.
The W program can be selected regardless of
the position of the gear selector, but is only
operational when the selector is in position D.
2nd and 6th gear also have lock-up on the 6-speed automatic gearbox.
NOTE
Depending on the engine temperature
when the engine is started, the idle speed
after a cold start may be higher than normal for certain engine types.
Adaptive system
The gearbox is controlled by what is known
as an adaptive system. The system continually monitors how the gearbox is behaving
and senses every gear change for optimum
change quality.
Lock-up function
The gears have a lock-up function (locked
gears), which gives better engine braking and
lower fuel consumption.
06 Starting and driving
Automatic gearbox
Kick-down
When the accelerator pedal is pressed all the
way to the floor, beyond the position normally
regarded as full acceleration, a lower gear is
immediately engaged. This is known as kickdown.
–
Keep your foot on the brake pedal when
moving the gear selector to another position.
If the accelerator is released from the kickdown position, the gearbox automatically
changes up.
Kick-down is used when maximum acceleration is needed, such as for overtaking.
To prevent overrevving, the gearbox control
program has a protective downshift inhibitor
which prevents the kick-down function.
The kick-down function cannot be used in
manual gear position.
Safety systems
06
Cars with an automatic gearbox have special
safety systems:
Keylock
To remove the remote control key from the
ignition switch, the gear selector must be in
the P position. The key is locked in all other
positions.
Parking position (P)
Stationary car with engine running:
149
06 Starting and driving
All-wheel drive*
All-wheel drive – AWD
All-wheel drive is always engaged.
All-wheel drive means that all four road
wheels are driven at the same time. The
power is automatically distributed between
the front and rear wheels. An electronically
controlled clutch system distributes the
power to the pair of wheels that grips best.
This provides the best traction and prevents
wheel spin.
Under normal driving conditions, the majority
of power is transmitted to the front wheels.
All-wheel drive improves driving safety in rain,
snow and icy conditions.
06
150
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Brake system
Brake servo
If the car is rolling or is being towed with the
engine turned off, the brake pedal must be
pressed about five times harder than when
the engine is running. If the brake pedal is
depressed when the engine is started, you
will feel the pedal drop. This is normal and
due to the brake servo becoming active. This
may be more noticeable if the car has Emergency Brake Assistance (EBA).
WARNING
The brake servo only works when the
engine is running.
NOTE
If braking with the engine switched off,
press the brake pedal sharply once, not
repeatedly.
Brake circuits
This symbol illuminates if a brake
circuit is not working.
If a fault should occur in one of the circuits, it
is still possible to brake the car. The brake
pedal will travel further and may feel softer
than normal. Harder pressure on the pedal is
needed to produce the normal braking effect.
Dampness can affect braking
characteristics
Brake components become wet when the car
is driven in heavy rain, through pools of water
or when the car is washed. This may alter
brake pad friction characteristics so that
there is a delay before braking effect is
noticed.
Press the brake pedal lightly from time to
time if driving for long stretches in rain or slushy snow, as well as after setting off in very
damp or cold weather. This warms up the
brake pads and dries off any water. This precaution is also recommended before parking
the car for a long period in such weather conditions.
Maintenance
To keep the car as safe and reliable as possible, follow the Volvo service intervals as
specified in the Service and Warranty Booklet, see page 208.
IMPORTANT
The wear on the brake system's components must be checked regularly.
Contact a workshop for information about
the procedure or engage a workshop to
carry out the inspection - an authorised
Volvo workshop is recommended.
If the brakes are used heavily
When driving in the Alps or other roads with
similar characteristics, the car's brakes are
heavily loaded even if the brake pedal is not
being depressed especially hard.
Because speed is often low, the brakes are
not cooled as effectively as when driving on
flat roads at higher speed.
So as not to overload the brakes, shift down
when driving downhill instead of using the
foot brake. Use the same gear driving downhill as you would use driving uphill. This uses
engine braking more efficiently so the foot
brake is only required for brief periods.
06
Bear in mind that driving with a trailer puts an
additional load on the car's brakes.
}}
151
06 Starting and driving
Brake system
Anti-lock braking system (ABS)
The anti-lock braking system
(ABS) prevents the wheels from
locking up during braking.
This means the ability to steer is
maintained and it is easier to swerve to avoid
a hazard for example.
The ABS symbol illuminates for 2 seconds
when the engine is started in connection with
an automatic function check.
After the engine has been started, the ABS
will perform a brief self-test at a speed of
about 20 km/h. This can be felt and heard as
pulses in the brake pedal.
To get the most out of the ABS:
1. Depress the brake pedal with full force.
Pulses will be felt.
06
152
Electronic brake force distribution
system – EBD
The Electronic Brakeforce Distribution system
(EBD) is an integrated part of the ABS system. The EBD system controls the brake
force to the rear wheels so that the best possible braking force is always available. Pulses
will be heard and felt through the brake pedal
when the system regulates brake force.
WARNING
If the BRAKE and ABS warning symbols
illuminate at the same time, there may be a
fault in the brake system. If the level in the
brake fluid reservoir is normal at this stage,
drive carefully to the nearest workshop
and have the brake system checked - an
authorised Volvo workshop is recommended.
2. Steer the car in the direction of travel. Do
not release the pressure on the pedal.
If the brake fluid is under the MIN level in
the brake fluid reservoir, do not drive further before topping up the brake fluid.
Practice braking with the ABS system in a
traffic-free area and in different weather conditions.
The reason for the loss of brake fluid must
be investigated.
Emergency Brake Assistance – EBA
(Emergency Brake Assistance) For sudden
braking, full-strength braking is provided
instantaneously. The EBA function senses
when heavy braking is underway by registering how quickly the brake pedal is depressed.
Continue braking without easing off on the
brake pedal. The function is suspended when
the pressure on the brake pedal eases. This
function is always active. It cannot be disengaged.
NOTE
When EBA is activated the brake pedal
lowers slightly more than usual, depress
(hold) the brake pedal as long as necessary. If the brake pedal is released then all
braking ceases.
06 Starting and driving
Stability and traction control system*
General
Reduced operation
Operation
1. Turn the thumbwheel (1) until the DSTC
menu appears.
The Dynamic Stability and Traction Control
system DSTC (Dynamic Stability and Traction
Control) improves the car's traction and helps
the driver to avoid skidding.
DSTC ON means that the system function is unchanged.
A pulsing sound may be noticed during braking or acceleration when the system is in
action. The car may accelerate slower than
expected when the accelerator pedal is
depressed.
DSTC SPIN CONTROL OFF means that
system operation is reduced.
G028511
2. Press and hold RESET (2) until the menu
is changed.
Active Yaw Control
The function limits the driving and brake force
of the wheels individually in order to stabilise
the car.
Spin Control
The function prevents the driving wheels from
spinning against the road surface during
acceleration.
Traction control system
The function is active at low speed and transfers power from the driving wheel that is spinning to the one that is not.
Thumbwheel
RESET button
System operation during skidding and acceleration can be partially deactivated.
Operation during skidding is then delayed
and so allows more skidding which provides
greater freedom for dynamic driving. Traction
in deep snow or sand is improved at the
same time as acceleration is no longer limited.
The system remains reduced until the
driver reactivates it or until the engine is
switched off - after the engine is started
the next time DSTC is back in its normal
mode again.
WARNING
Suppressing system function may alter the
driving characteristics of the car.
06
NOTE
DSTC ON is shown for several seconds
on the display each time the engine is
started.
}}
* Option/accessory, for more information, see Introduction.
153
06 Starting and driving
Stability and traction control system*
Messages on the display
ANTI-SKID TEMPORARILY OFF means
that the system has been temporarily reduced
due to excessive brake temperature.
–
The function is reactivated automatically
when the brakes have cooled.
ANTI-SKID SERVICE REQUIRED system
disabled due to a fault.
–
Stop the car in a safe place and turn off
the engine.
> If the message remains when the
engine is restarted, drive to a workshop. An authorised Volvo workshop is
recommended.
Symbols in the combined instrument
panel
•
The symbol illuminates and goes out
again after approx. 2 seconds when the
engine is started
•
Indicates system check.
The symbol flashes
•
Indicates that the system is operating.
Indicates a fault in the DSTC system.
1. Stop the car in a safe place and turn off
the engine.
2. Restart the engine.
•
If the warning symbol goes out, the fault
was temporary and it is not necessary to
visit a workshop.
•
If the warning symbol remains illuminated
then a workshop should check the system - an authorised Volvo workshop is
recommended.
The symbol illuminates with a constant
yellow glow
Symbol for Warning
DSTC system
06
154
The symbol illuminates and stays lit
At the same time the display shows ANTISKID SERVICE REQUIRED.
At the same time the display
shows TRACTION CONTROL
TEMPORARILY OFF .
•
Indicates that the system has been temporarily reduced due to excessive brake
temperature.
Automatic reactivation of the function takes
place when the brake temperature has
returned to normal.
* Option/accessory, for more information, see Introduction.
WARNING
Under normal driving conditions, the
DSTC system improves the car's road
safety, but this should not be taken as a
reason to increase speed.
Always follow the usual precautions for
safe cornering and driving on slippery road
surfaces.
06 Starting and driving
Park assist syst*
General1
Variants
Rear parking assistance
Parking assistance is available in two variants:
The distance covered to the rear of the car is
about 1.5 m. Rear parking assistance is activated when reverse gear is engaged. The signal comes from the rear loudspeakers.
•
•
Rear only
Both front and rear
Function
The system is switched on automatically
when the car is started at which point the
lamp in the switch for parking assistance illuminates.
The display shows the text message PARK
ASSIST ACTIVE if reverse gear is engaged
or if the front sensors detect an object.
Parking assistance front and rear.
Parking assistance is used as an aid to parking. A signal indicates the distance to a
detected object.
WARNING
Parking assistance does not relinquish the
driver's own responsibility during parking.
The sensors have blind spots where
objects cannot be detected. Be aware of
children and animals near the car.
1
Parking assistance is active at speeds below
15 km/h. The system is deactivated at higher
speeds. When the speed is below 10 km/h
the system is reactivated.
The frequency of the signal increases as you
come closer to an object in front of or behind
the car. If the volume of another audio source
from the audio system is high, then this is
automatically lowered.
The tone becomes constant at a distance of
about 30 cm. If there are objects within this
distance behind or in front of the car, the signal alternates between left and right-hand
speakers.
The system must be deactivated when
reversing with a trailer, or bike carrier on the
towbar or similar. Otherwise the trailer or bike
carrier would trigger the sensors.
Rear parking assistance is deactivated automatically when towing a trailer if a Volvo genuine trailer cable is used.
Front parking assistance
The distance covered to the front of the car is
about 0.8 metres. The signal comes from the
front loudspeakers.
Front parking assistance cannot be combined
with extra lights because the sensors are
affected by the extra lights.
06
Fault indicator
If the information symbol illuminates with constant glow and the
display shows PARK ASSIST
SERVICE REQUIRED then parking assistance is disengaged.
Depending on the market, the Parking assistance system may be either Standard, Option or Accessory.
}}
* Option/accessory, for more information, see Introduction.
155
06 Starting and driving
Park assist syst*
IMPORTANT
In certain conditions the parking assistance system may produce incorrect warning signals that are caused by external
sound sources that emit the same ultrasonic frequencies that the system works
with.
switched on again with the switch and the
lamp illuminates.
Cleaning the sensors
Examples of such sources include horns,
wet tyres on asphalt, pneumatic brakes
and exhaust noises from motorcycles etc.
G026946
Off/On
Parking assistance sensors.
06
G027104
The sensors must be cleaned regularly to
ensure that they work properly. Clean them
with water and car shampoo.
Button position in the row may vary.
NOTE
Dirt, ice and snow covering the sensors
may cause incorrect warning signals.
Parking assistance can be deactivated with
the button in the switch panel. The lamp in
the switch goes out. Parking assistance is
156
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Blind Spot Information System - BLIS*
General
BLIS is an information system that under certain conditions can help to draw the driver's
attention to vehicles moving in the same
direction in the so-called "blind spot".
Blind spots
The system is designed to work most effectively when driving in dense traffic on multilane highways.
G020295
BLIS is based on digital camera technology.
The cameras (1) are located under the door
mirrors.
Rearview mirror with BLIS system.
BLIS camera
Indicator lamp
BLIS symbol
WARNING
The system is a supplement to, not a
replacement for, a safe driving style and
use of the rearview mirrors. It can never
replace the driver's attention and responsibility. The responsibility for changing lanes
safely always rests with the driver.
When a camera has detected a vehicle inside
the blind spot zone the indicator lamp (2) illuminates with a constant glow.
NOTE
The lamp illuminates on the side of the car
where the system has detected the vehicle. If the car is overtaken on both sides at
the same time then both lamps illuminate.
BLIS advises the driver with a message if a
fault arises in the system. If for example the
system's cameras are obscured then the
BLIS indicator lamp flashes and a message is
shown in the information display. In such
cases, check and clean the lenses. If necessary, the system can be switched off temporarily by pressing the BLIS button, see
page 158.
"Blind spots" intended to be covered by BLIS
cameras.
Distance A = approx. 3.0 m
Distance B = approx. 9.5 m
06
Cleaning
In order to work most effectively the BLIS
camera lenses must be clean. The lenses can
be cleaned with a soft cloth or damp sponge.
Clean the lenses carefully so that they are not
scratched.
}}
* Option/accessory, for more information, see Introduction.
157
06 Starting and driving
Blind Spot Information System - BLIS*
The lenses are electrically heated to melt
ice or snow. If necessary, brush snow
away from the lenses.
When BLIS operates
The system operates when the car is driven
at a speed above 10 km/h.
designed to detect motor vehicles such as
cars, trucks, buses and motorcycles.
In darkness the system reacts to the headlamps of surrounding vehicles. Vehicles with
headlamps that are switched off are not
detected by the system. This means for
example that the system does not react to a
trailer without headlamps which is towed
behind a car or truck.
Overtaking
The system is designed to react if you overtake another vehicle at a speed of up to
10 km/h faster than the other vehicle.
The system is designed to react if you are
overtaken by a vehicle travelling up to
70 km/h faster than your vehicle.
06
WARNING
The system does not react to cyclists or
moped riders.
The BLIS cameras have limitations similar
to those of the human eye, i.e. they do not
see as well in e.g. heavy snowfall, strong
oncoming light or thick fog.
WARNING
BLIS does not work in sharp bends.
BLIS does not work when the car is
reversing.
A wide trailer coupled to the car can conceal other vehicles in adjacent lanes. It can
prevent the vehicle in the screened area
from being detected by BLIS.
Daylight and darkness
In daylight the system reacts to the shape of
the surrounding vehicles. The system is
158
Activate/deactivate
* Option/accessory, for more information, see Introduction.
G026955
IMPORTANT
Button for activating/deactivating.
BLIS is activated when the engine is started.
The indicator lamps in the door panels flash
three times when BLIS is activated.
The system can be deactivated/activated by
pressing BLIS.
When BLIS is deactivated the light in the button goes out and a text message is shown on
the instrument panel display.
When BLIS is activated the light in the button
illuminates, a new text message is shown on
the display and the indicator lamps in the
door panels flash three times. Press the
READ button to clear the text message. For
more information on messages, see page 60.
06 Starting and driving
Blind Spot Information System - BLIS*
BLIS system message
Text on the
displayA
Specification
Text on the
displayA
BLIND-SPOT
INFO SYSTEM
ON
The BLIS system is
activated.
BLIND-SPOT
SYST L CAMERA BLOCKED
BLIND-SPOT
SYST SERVICE
REQUIRED
Blind spot syst. disengaged - contact a
workshop.
BLIND-SPOT
SYST FUNCTION REDUCED
Reduced function in
the data transmission
between the BLIS
system's camera and
the car's electrical
system.
The camera resets
itself when the data
transmission between
the BLIS system's
camera and the car's
electrical system
returns to normal.
BLIND-SPOT
SYST R CAMERA BLOCKED
Right camera blocked
- clean the lens.
A
Limitations
Specification
Left camera blocked clean the lens.
In some situations the BLIS indicator lamp
may illuminate despite there being no other
vehicle within the blind spot.
NOTE
BLIND-SPOT
SYST CAMERAS
BLOCKED
One or both cameras
blocked - clean the
lenses.
BLIND-SPOT
INFO SYSTEM
OFF
The BLIS system is
deactivated.
Messages above are only shown if the remote control key
is in key position II (or if the engine is running) and BLIS is
active (i.e. if the driver has not switched off the system).
IMPORTANT
If the BLIS indicator lamp illuminates on
isolated occasions despite there being no
other vehicle within the blind spot then this
does not mean that a fault has arisen in
the system.
In the event of a fault in the BLIS system
the display shows the text BLIND-SPOT
SYST SERVICE REQUIRED.
Here are some examples of situations where
the BLIS indicator lamp may illuminate even if
there is no other vehicle within the blind spot.
Repair of the BLIS system components
must only be performed by a workshop an authorised Volvo workshop is recommended.
06
Reflection from shiny wet road surface.
}}
* Option/accessory, for more information, see Introduction.
159
06 Starting and driving
G018177
Blind Spot Information System - BLIS*
Own shadow on large light smooth surface, e.g.
noise barrier or concrete road surface.
Low stationary sunlight shining into the camera.
06
160
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Towing and recovery
Jump starting
WARNING
Use a donor battery if the battery is discharged and the engine does not start. Do
not tow the car to bump start it, see
page 163.
The steering lock remains in the position it
was in when the power was cut off. The
steering lock must be unlocked before
towing.
The remote control key must be in key
position II. Never remove the remote control key from the ignition switch while driving or when the car is being towed.
IMPORTANT
Bump starting the car can damage the catalytic converter.
WARNING
Towing
The brake servo and power steering do not
work when the engine is switched off. The
brake pedal must be pressed about five
times harder than normal, and the steering
will be considerably heavier than normal.
Find out the highest legal speed for towing
before towing the car.
The car must always be towed facing forward.
2. For the driver of the towing vehicle: Drive
gently.
For the driver of the vehicle being towed:
Keep the towline taut by holding your foot
gently pressed on the brake pedal in
order to avoid unnecessary jerking.
Automatic gearbox
–
Move the gear selector to N position and
release the parking brake.
Cars with automatic gearbox must not be
towed at speeds above 80 km/h or further
than 80 km.
Towing eye
Before towing the towing eye must be bolted
securely onto the bumper. The socket and
cover for the towing eye are on the right-hand
side of each bumper.
06
G028528
1. Unlock the steering wheel lock so that the
car can be steered.
The towing eye is in the tool kit in the cargo
area.
Proceed as follows:
1. Release the bottom edge of the cover (A)
with a screwdriver or a coin.
2. Screw in the towing eye (B).
}}
161
06 Starting and driving
Towing and recovery
3. Screw the eye securely into place right up
to the flange (C). You can use a wheel
wrench.
•
After use, unscrew the towing eye and
refit the cover.
IMPORTANT
On certain cars with fitted towbar the towing eye cannot be secured in the rear
mounting. In which case, secure the tow
rope in the towbar. For this reason, it is
advisable to always store the detachable
towbar in the car.
Recovery
The car must always be towed with the
wheels rolling forward.
IMPORTANT
06
•
An all-wheel drive car (AWD) with
raised front suspension must not be
towed at speeds above 70 km/h. It
should not be towed further than
50 km.
WARNING
The towing eye is only designed for towing
on roads - not for recovering the car. Call a
recovery service for recovery assistance.
162
06 Starting and driving
Jump starting
Starting with a donor battery
3. If the donor battery is installed in another
car - switch off the donor car's engine
and make sure that the two cars do not
touch each other.
9. Start the engine of the "donor car" and
allow it to run a few minutes at a speed
slightly higher than idle
approx. 1500 rpm.
4. Connect one of the red jump lead's
clamps to the donor battery's positive
terminal (1).
10. Start the engine in the car with the discharged battery.
IMPORTANT
G030860
Connect the start cable carefully to avoid
short circuits with other components in the
engine compartment.
The battery is fitted in the rear of the car (see
page 221) but there are also connection points
under the bonnet.
If the battery is flat then the car can be
started with current from another battery.
When jump starting the car, the following
steps are recommended to avoid short circuits or other damage:
1. Turn the remote control key to key position 0.
2. Check that the donor battery has a voltage of 12 V.
5. Connect the red jump lead's other clamp
onto the car's positive terminal (2).
> A spring-loaded cover over the car's
extra positive terminal must first be
folded up!
6. Connect one of the black jump lead's
clamps to the donor battery's negative
terminal (3).
IMPORTANT
Do not touch the crocodile clips during the
start procedure. There is a risk of sparks
forming.
11. Remove the jump leads in reverse order first the black and then the red.
> Make sure that none of the black jump
lead's clamps comes into contact with
the battery's positive terminal or the
clamp connected to the red jump lead!
06
7. Fit the second clamp on a grounding
point e.g. one of the engine's lifting eyes
(4).
8. Check that the jump lead clamps are
affixed securely so that there are no
sparks during the starting procedure.
}}
163
06 Starting and driving
Jump starting
WARNING
•
The battery can generate oxyhydrogen
gas, which is highly explosive. A spark
can be formed if a jump lead is connected incorrectly, and this can be
enough for the battery to explode.
•
The battery contains sulphuric acid,
which can cause serious burns.
•
If sulphuric acid comes into contact
with eyes, skin or clothing, flush with
large quantities of water. If acid
splashes into the eyes - seek medical
attention immediately.
For more information on the car's battery, see
page 220.
06
164
06 Starting and driving
Driving with a trailer
General
Payload depends on the car's kerb weight.
The total of the weight of the passengers and
all accessories, e.g. towbar, reduces the car's
payload by a corresponding weight. For more
detailed information on weights, see
page 288.
If the towing bracket is fitted by an authorised
Volvo workshop, then the car is delivered with
the necessary equipment for driving with a
trailer.
•
The car's towing bracket must be of an
approved type.
•
If the towbar is retrofitted, check with
your Volvo dealer that the car is fully
equipped for driving with a trailer.
•
Distribute the load on the trailer so that
the weight on the towing bracket follows
the specified maximum towball load.
•
Increase the tyre pressure to the recommended pressure for a full load. For tyre
pressure label location, see page 183.
•
The engine is loaded more heavily than
usual when driving with a trailer.
•
Do not tow a heavy trailer when the car is
brand new. Wait until it has been driven
at least 1000 km.
•
The brakes are loaded much more than
usual on long and steep downhill slopes.
Downshift to a lower gear and adjust your
speed.
•
Automatic gearbox
NOTE
For safety reasons, the maximum permitted speed for the car when coupled with
a trailer should not be exceeded. Follow
the regulations in force for the permitted
speeds and weights.
Some models require an oil cooler for the
automatic gearbox when driving with a
trailer. Check with your nearest Volvo
dealer as to what applies to your car if you
have a retrofitted towbar.
Trailer weights
For information on Volvo's permitted trailer
weights, see page 288.
WARNING
Follow the stated recommendations for
trailer weights. Otherwise, the car and
trailer may be difficult to control in the
event of sudden movement and braking.
Overheating
When driving with a trailer in hilly terrain in a
hot climate there may be a risk of overheating.
•
An automatic gearbox selects the optimum gear related to load and engine
speed.
•
In the event of overheating a warning
symbol illuminates on the instrument
panel combined with a text message follow the recommendation given.
NOTE
The stated maximum permitted trailer
weights are those permitted by Volvo.
National vehicle regulations can further
limit trailer weights and speeds. Towbars
can be certified for higher towing weights
than the car can actually tow.
06
Steep inclines
•
Do not lock the automatic transmission in
a higher gear than the engine "can cope
with" - it is not always a good idea to
drive at a high gear with low engine revolutions.
•
Maintain a low speed when driving with a
trailer up long, steep ascents.
•
Avoid driving with a trailer on inclines of
more than 12%.
}}
165
06 Starting and driving
Driving with a trailer
Parking on a hill
Levelling
1. Depress the foot brake.
If your car is equipped with automatic levelling, the rear suspension always retains the
correct ride height regardless of load. When
the car is stationary, the rear suspension
sinks. This is completely normal. When starting with a load, the level is pumped up after
a certain distance.
2. Activate the parking brake.
3. Move the gear selector to position P.
4. Release the foot brake.
•
Move the gear selector to park position P
after parking a car with an automatic
gearbox and with a trailer hitched. Always
use the parking brake.
•
Block the wheels with chocks when parking a car with hitched trailer on a hill.
Starting on a hill
1. Depress the foot brake.
2. Move the gear selector to driving position D.
06
166
3. Release the parking brake.
4. Release the foot brake and start driving
off.
06 Starting and driving
Towing equipment*
Towbar
Trailer cable
Storing the towbar
If the car is equipped with a detachable towbar, the installation instructions for the loose
section must be followed carefully, see
page 169.
WARNING
Follow the installation instructions
carefully.
•
The detachable section must be
locked with the key before setting off.
•
Check that the indicator window
shows green.
Important checks
•
The towbar's towball must be cleaned
and greased regularly.
NOTE
Towbar storage space.
IMPORTANT
Always remove the towbar after use and
store it in the appointed location in the car,
firmly fastened with its strap.
G014589
•
G031114
If the car is fitted with a Volvo detachable
towbar:
An adapter is required if the car's towing
bracket has 13 pin electrics and the trailer
has 7 pin electrics. Use an adapter cable
approved by Volvo. Make sure the cable does
not drag on the ground.
06
When a hitch with a vibration damper is
used, the towball must not be lubricated.
}}
* Option/accessory, for more information, see Introduction.
167
06 Starting and driving
Towing equipment*
G027109
G026682
G027108
Specifications
Dimensions for mounting points (mm)
06
168
Fixed or detachable towbar
A
B
C
D
E
F
G
1110
85
1081
541
122
50
354
1
Side member
2
Ball centre
* Option/accessory, for more information, see Introduction.
06 Starting and driving
Detachable towbar*
1. Remove the protective cover by first
and then pulling
pressing in the catch
.
the cover straight back
2. Ensure that the mechanism is in the
unlocked position by turning the key
clockwise.
G020302
G017317
G020301
Fitting the towbar
3. Check that the indicator window (3)
shows red. If the window does not show
red, press in (1) and turn the locking
wheel anticlockwise (2) until you hear a
click.
06
}}
* Option/accessory, for more information, see Introduction.
169
06 Starting and driving
4. Insert the towbar until you hear a click.
5. Check that the indicator window shows
green.
06
170
* Option/accessory, for more information, see Introduction.
G020307
G020306
G020304
Detachable towbar*
6. Turn the key anticlockwise to locked
position. Remove the key from the lock.
06 Starting and driving
Detachable towbar*
7. Check that the towbar is secure by pulling it up, down and back.
WARNING
If the towbar is not fitted correctly then it
must be detached and reattached in
accordance with the previous instructions.
G020301
G020310
G020309
Removing the towbar
8. Safety cable.
WARNING
1. Insert the key and turn it clockwise to the
unlocked position.
Take care to secure the trailer's safety
cable in the intended bracket.
06
IMPORTANT
Only grease in the ball for the towing hitch,
the remainder of the towbar should be
clean and dry.
}}
* Option/accessory, for more information, see Introduction.
171
06 Starting and driving
2. Push in the locking wheel (1) and turn it
anticlockwise (2) until you hear a click.
3. Turn the locking wheel down fully, until it
comes to a stop. Hold it in this position
while pulling the towbar rearward and
upward.
06
WARNING
Secure the towbar safely if it is stored in
the car, see page 167.
172
* Option/accessory, for more information, see Introduction.
G017318
G020314
G020312
Detachable towbar*
4. Push on the protective cover.
06 Starting and driving
Adjusting headlamp pattern
Correct light pattern for left or righthand traffic
should align with the red dot on the respective template. The long red line on the illustrations corresponds to the line in the headlamp
lens to which the template should be
matched.
Xenon headlamps
After copying the templates, check the measurements so that the reference measurements cover enough of the beam pattern.
Position each template so that the arrows
point towards the centre and the dot on the
template matches the dot on the headlamp
lens. The template marking > < should be
aligned with the line on the headlamp lens.
The templates are for both LHD and RHD
variants and are positioned as illustrated.
G020317
The upper illustration is for LHD cars. The
lower illustration is for RHD cars.
Headlamp pattern for left-hand traffic.
Headlamp pattern for right-hand traffic.
Halogen headlamps
Copy templates 1 and 2. Check the measurements to ensure they are correct. Transfer the
template to a self-adhesive, waterproof material and cut it out.
So as not to dazzle oncoming drivers, the
headlamp beam pattern can be altered by
masking the headlamps. The quality of the
beam pattern may not be as good.
Position each template so that the arrows
point towards the centre and the dot on the
template matches the dot on the headlamp
lens.
Headlamp masking
Reference measurements template
1 and 2
Copy the templates, see page 176. Transfer
the pattern to a self-adhesive, waterproof
material such as opaque tape for example.
Copy templates 3 and 4. Check the measurements to ensure they are correct. Transfer the
template to a self-adhesive, waterproof material and cut it out.
Reference measurements template 3
The line between the > < markings on the
templates should be approx. 140 mm.
Reference measurements template 4
The line between the > < markings on the
templates should be approx. 112 mm.
Adjusting headlamp pattern for Active Xenon
headlamps (ABL), see page 62.
06
The long sides of the templates should be
approx. 82 mm.
The mask is positioned using the dot (5) in the
headlamp lens as a reference point, which
}}
173
06 Starting and driving
G030200
Adjusting headlamp pattern
Left-hand drive car in left-hand traffic.
Masking on right-hand halogen lens
Masking on left-hand halogen lens
06
Masking on right-hand Xenon lens
Masking on left-hand Xenon lens
Control point in headlamp lens.
174
06 Starting and driving
G030201
Adjusting headlamp pattern
Right-hand drive car in right-hand traffic.
Masking on left-hand halogen lens
Masking on right-hand halogen lens
Masking on left-hand Xenon lens
06
Masking on right-hand Xenon lens
Control point in headlamp lens.
}}
175
06 Starting and driving
Adjusting headlamp pattern
06
Templates for masking.
176
06 Starting and driving
06
177
General..................................................................................................
Tyre pressure........................................................................................
Warning triangle* and spare wheel *.....................................................
Changing wheels...................................................................................
Emergency puncture repair*.................................................................
178
* Option/accessory, for more information, see Introduction.
180
183
184
187
190
WHEELS AND TYRES
07 Wheels and tyres
General
Driving characteristics and tyres
Speed ratings
The tyres greatly affect the car's driving characteristics. The type of tyre, dimensions, tyre
pressure and speed rating are important for
how the car performs.
The car is approved as a whole, which means
that dimensions and speed ratings must not
differ from those specified on the vehicle registration document. The only exception to
these conditions is winter tyres (both those
with metal studs and those without). If such a
tyre is chosen, the car must not be driven
faster than the speed rating of the tyre (for
example, class Q can be driven at a maximum of 160 km/h).
When changing tyres, ensure that tyres of the
same type and dimensions, and preferably
also the same make, are fitted to all four
wheels. Follow the recommended tyre pressures specified on the tyre pressure label, see
page 297.
Designation of dimensions
The dimensions are stated on all car tyres.
Example of designation:
235/60R18 103 V.
07
180
Remember that traffic regulations determine
how fast a car can be driven, not the speed
class of the tyres.
Note! Maximum permitted speeds indicated.
Q
160 km/h (used only on winter tyres)
235
Tyre width (mm)
T
190 km/h
60
Ratio between tyre wall height and
tyre width (%)
H
210 km/h
R
Radial ply
V
240 km/h
18
Rim diameter in inches (")
W
270 km/h
103
Tyre load index (in this case 615 kg)
Y
300 km/h
V
Speed rating for maximum permitted
speed (in this case 240 km/h).
New tyres
Tyres are perishable. After a few years they
begin to harden at the same time as the friction capacity/characteristics gradually deteriorate. For this reason, aim to get as fresh
tyres as possible when you replace them.
This is especially important with regard to
winter tyres. The last four digits in the
sequence mean the week and year of manufacture. This is the tyre's DOT marking
(Department of Transportation), and this is
stated with four digits, for example 1510. The
tyre in the illustration was manufactured in
week 15 of 2010.
Tyre age
All tyres older than six years should be
checked by an expert even if they seem
undamaged. The reason for this is that tyres
07 Wheels and tyres
General
age and decompose, even if they are hardly
ever or never used. The function can therefore be affected due to the tyre's constituent
materials being broken down. In such a case
the tyre should then not be used.This also
applies to spare tyres, winter tyres and tyres
saved for future use. Examples of external
signs which indicate that the tyre is unsuitable for use are cracks or discoloration.
tinuing forwards in a straight line rather than
having the rear end skidding to one side,
resulting in possible complete loss of control
over the car. This is why it is important for the
rear wheels never to lose grip before the front
wheels.
The age of the tyre can be determined by the
DOT marking, see illustration above.
Tyres with tread wear indicators
Wheels must be stored lying down or hanging
up - never standing up.
Winter tyres
Volvo recommends winter tyres with specific
winter tyre dimensions. Tyre dimensions are
dependent on engine variant. When driving
on winter tyres, they must be fitted to all four
wheels.
NOTE
More even wear and maintenance
Ask a Volvo dealer which rim and tyre
types are most suitable.
Studded tyres
Studded winter tyres should be run in gently
for 500 – 1000 km so the studs settle properly
into the tyre. This gives the tyre, and especially the studs, a longer service life.
G020323
The correct tyre pressure results in more even
wear, see page 297. Driving style, tyre pressure, climate and road condition affect how
quickly your tyres age and wear. To avoid differences in tread depth and to prevent wear
patterns arising, the front and rear wheels can
be switched with each other. A suitable distance for the first change is approx. 5000 km
and then at 10 000 km intervals. Volvo recommends that you contact an authorised
Volvo workshop for checking if you are uncertain about tread depth. If significant differences in wear (>1 mm difference in tread depth)
between tyres have already occurred, the
least worn tyres must always be placed on
the rear. Understeer is normally easier to correct than oversteer, and leads to the car con-
Change to new tyres as soon as possible.
Remember that tyres with little tread depth
provide very poor grip in rain and snow.
Tread wear indicators.
Tread wear indicators are narrow treadless
bands across the width of the tread. On the
side of the tyre are the letters TWI (Tread
Wear Indicator). When the tyre's tread depth
is down to 1.6 mm, the tread depth will be
level in height with the tread wear indicators.
NOTE
The legal provisions for the use of studded
tyres vary from country to country.
07
Tread depth
Road conditions with ice, slush and low temperatures place considerably higher demands
on tyres than summer conditions. It is therefore recommended not to drive on winter
}}
181
07 Wheels and tyres
General
tyres that have a tread depth of less than four
millimetres.
Summer and winter wheels
slush out of the way are adversely affected.
Tyres with the greatest tread depth should
always be fitted to the rear of the car (to
decrease the risk of skidding).
Snow chains
Snow chains may only be used on the front
wheels. This also applies to all-wheel-drive
cars.
WARNING
Use Volvo genuine snow chains or equivalent chains designed for the car model,
and tyre and rim dimensions. In the event
of uncertainty Volvo recommends that you
consult an authorised Volvo workshop.
The wrong snow chains may cause serious
damage to your car and lead to an accident.
07
182
G020325
Never drive faster than 50 km/h with snow
chains. Avoid driving on bare ground as this
wears out both the snow chains and tyres.
Check that the snow chain does not make
contact anywhere and that it is correctly fitted
and well tensioned.
Volvo recommends that you contact an
authorised Volvo workshop for checking if
you are uncertain about tread depth.
The arrow shows the tyre's direction of rotation
When summer and winter wheels are
changed, see page 187, the wheels should
be marked with which side of the car they
were mounted on, for example L for left and
R for right. Tyres with a tread pattern which
are designed to only turn in one direction
have the direction of rotation marked with an
arrow. The tyre must always rotate in the
same direction throughout its lifespan. Tyres
should only be switched between front and
rear positions, never between left and righthand sides, or vice versa. If the tyre is mounted incorrectly, the car's braking characteristics and capacity to force rain, snow and
07 Wheels and tyres
Tyre pressure
Recommended tyre pressure
Checking the tyre pressure
Check the tyre pressure regularly.
Tyre pressure affects travelling comfort, road
noise and steering characteristics.
NOTE
G020791
Tyre pressure decreases over time, this is
a natural phenomenon. Tyre pressure also
varies depending on ambient temperature.
The tyre pressure label on the driver's side
door pillar shows which pressures the tyres
should have at different loads and speed conditions.
Stated on the decal:
•
Tyre pressures for the car's recommended tyre size
•
•
ECO pressure1
1
Spare wheel tyre pressure (Temporary
Spare).
Even after several kilometres of driving, the
tyres warm up and the pressure increases. So
air must not be released if the pressure is
checked when the tyres are warm. While the
pressure must be increased if it is too low.
Inadequately inflated tyres increase fuel consumption, shorten tyre lifespan and impair the
car's roadholding. Driving on tyres with tyre
pressure that is too low can also result in the
tyres overheating and disintegrating.
For information on the correct tyre pressure,
see page 297. The specified tyre pressures
refer to "cold tyres". ("Cold tyres" means the
tyres are the same temperature as the ambient temperature.)
Fuel economy, ECO pressure
07
At speeds under 160 km/h, the general tyre
pressure for full load is recommended in
order to obtain optimum fuel economy.
ECO pressure results in improved fuel economy.
183
07 Wheels and tyres
Warning triangle* and spare wheel *
Warning triangle
After use:
–
Pack everything in reverse order.
Make sure that the warning triangle with case
is securely fastened in the compartment.
G027065
Spare wheel Temporary Spare*
Follow the regulations in force for the use of a
warning triangle* in the country in which you
are driving.
Use the warning triangle as follows:
1. Detach the warning triangle case. It is
held in place with a Velcro strap.
07
The spare wheel (Temporary spare) is only
intended for use temporarily and must be
replaced by an ordinary wheel as soon as
possible. The car's handling may be altered
by the use of the spare wheel. The spare
wheel is smaller than the normal wheel. The
car's ground clearance is affected accordingly. Pay attention to high kerbs and do not
machine wash the car. If the spare wheel is
fitted on the front axle, you cannot use snow
chains at the same time. On all-wheel drive
cars the drive on the rear axle can be disconnected. The spare wheel must not be
repaired. The correct tyre pressure for the
spare wheel is stated in the tyre pressure
table, see page 297.
2. Remove the warning triangle from its
case (A).
3. Fold out the four support legs on the
warning triangle.
IMPORTANT
Never drive faster than 80 km/h with a
spare wheel on the car.
4. Fold out both red sides of the warning triangle. Position the warning triangle in a
suitable place with regard to traffic.
184
* Option/accessory, for more information, see Introduction.
IMPORTANT
The car must never be driven fitted with
more than one "Temporary Spare" wheel.
07 Wheels and tyres
Warning triangle* and spare wheel *
G030879
Spare wheel – removing
The spare wheel is located under the car. The
jack*, tool kit* and crank are located under
the floor hatch. The crank is in two parts. One
part is in the tool kit, and the other is under
the tool kit.
NOTE
There is a puller spanner in the tool kit to
remove the hub cap (certain wheel
options).
4. Loosen the tyre by cranking anticlockwise
until you reach the stop.
The location of the jack varies:
Cars seating seven
NOTE
Cars seating five
The cable could damage the car if it hangs
free while driving.
Proceed as follows to release the spare
wheel:
1. Lower the bottom of the tailgate and lift
up the floor hatch in the cargo area.
2. Take the two parts of the crank and
assemble.
3. Fit the crank in the winch.
5. Release the wheel from the cable and
wind up the cable clockwise.
07
6. Place the punctured tyre in the cargo
area. The tool kit contains a plastic bag
for the tyre.
}}
* Option/accessory, for more information, see Introduction.
185
07 Wheels and tyres
Warning triangle* and spare wheel *
NOTE
The spot under the car is only intended for
the car's original spare wheel. Do not
place any other wheels there.
3. Angle the wheel so that it comes in over
the exhaust system.
4. Hold down the rear edge of the wheel
while cranking it in.
5. Place the wheel above the rear axle,
against the floor.
Spare wheel – refitting
6. Crank to the stop point.
7. Check that the wheel is properly secured.
G026996
WARNING
07
It is best to have two people put the spare
wheel back in place. One person to crank and
the other to guide the wheel.
1. Crank out the cable and place its anchor
in the centre hole of the wheel.
Check that the right mounting points are
being used. A production anchorage with
pin is located between the jacking points.
This is not strong enough to use to lift the
car. If you are unsure about the location of
the jacking points, Volvo recommends that
you contact an authorised Volvo workshop. An incorrectly fitted jack could damage the door and body.
Tools - returning into place
The tools and jack* must be returned to their
correct places after use. The jack must be
cranked to the correct position, see the preceding illustration, in order to have space.
2. Slowly crank (clockwise) the cable in a
bit.
186
* Option/accessory, for more information, see Introduction.
IMPORTANT
The tools and jack* must be stored in the
intended location in the car's cargo area
when not in use.
First aid*
A case with first aid equipment is located in
the cargo area.
07 Wheels and tyres
Changing wheels
Removing wheels
WARNING
Check that the jack is not damaged, that
the threads are thoroughly lubricated and
that it is free from dirt.
NOTE
G026997
Volvo recommends only using the jack*
that belongs to the car model in question,
which is indicated on the jack's label.
Remember to set out the warning triangle if
you must change a wheel in a trafficked area.
There are two jacking points on each side of
the car. The jacking points are centred under
the bottom of the doors.
1. Park the car on level and firm ground.
2. Move the gear selector to the P position
and apply the parking brake.
3. Place chocks in front of and behind the
wheels which will remain on the ground to
prevent them from rolling. Use stones or
wooden blocks for example.
The label also indicates the jack's maximum lift capacity at a specified minimum
lifting height.
4. Take out the jack*, wheel wrench and
crank, see location see page 185. If
another jack is selected, see page 209.
WARNING
Never crawl under the car when it is raised
on the jack. The car could fall, causing
injuries.
The car's original jack should only be used
when changing wheels. All other work on
the car should be done using workshop
jacks and axle stands under the part of the
car that is raised.
The jack screw should be kept well lubricated.
If the surface is too soft, the jack could
slide to the side and the car could fall. No
one should be in the car when the wheel is
being changed.
NOTE
The car's regular jack is designed only for
use occasionally and for a short time, such
as when changing a wheel with a punctured tyre, switching between summer
tyres and winter tyres, etc. Only the jack
belonging to the specific model is to be
used to jack up the car. If the car is to be
jacked up more often, or for a longer time
than is required just to change a wheel,
use of a garage jack is recommended. In
this instance, follow the instructions for
use that come with the equipment.
07
}}
* Option/accessory, for more information, see Introduction.
187
07 Wheels and tyres
Changing wheels
5. Use the wheel brace to loosen the wheel
bolts ½-1 turn. Turn anticlockwise.
WARNING
Never position anything between the
ground and the jack, nor between the jacking point and the jack.
WARNING
G020332
G027000
If the jack is positioned incorrectly, the car
could fall. Risk of injury.
6. Place the jack under the jacking point and
crank it up towards the car floor. There is
an recess in the plastic cover at each
anchorage point. Check that the jack sits
securely in the anchorage. Then adjust
the jack so that its foot is positioned vertically under the anchorage. See illustration.
IMPORTANT
The ground must be firm, smooth and
level.
07
7. Lift the car until the wheel is free.
8. Remove the wheel bolts and lift off the
wheel.
188
07 Wheels and tyres
Changing wheels
Fitting the wheel
1. Clean the contract surfaces on the wheel
and hub.
2. Put on the wheel. Screw in the wheel
bolts.
3. Lower the car so that the wheel cannot
rotate.
4. Tighten the wheel bolts alternately and in
torque steps. Tightening torque: 140 Nm
(14.0 kpm). It is important that they are
tightened to the correct torque. Check
with a torque wrench.
5. Screw the jack all the way down before
returning it to the cargo area. Then secure
it in place.
6. Check that the new tyre has the correct
amount of pressure.
NOTE
This wheel bolt may also be used for steel
wheel rims.
07
Make sure to use the correct type of bolt.
Volvo recommends that you contact the nearest Volvo workshop if you are in any doubt.
189
07 Wheels and tyres
Emergency puncture repair*
General
The emergency puncture repair kit is used to
seal a puncture as well as to check and
adjust the tyre pressure. It consists of a compressor and a bottle with sealing fluid. The kit
works as a temporary repair. The sealing fluid
bottle must be replaced before its expiration
date and after use.
The sealing fluid effectively seals tyres punctured in the tread.
NOTE
The emergency puncture repair kit is only
intended for sealing tyres with a puncture
in the tread.
NOTE
The jack is an option on cars equipped
with emergency puncture repair kit.
07
The emergency puncture repair kit has limited
capacity to seal tyres which have punctures
in the wall. Do not seal tyres with the emergency puncture repair kit if they have larger
slits, cracks or similar damage.
and 119. Choose the electrical socket that is
nearest the punctured tyre.
IMPORTANT
If the compressor for emergency puncture
repair is connected to one of the two sockets - see pages 62 and 76 - no other current consumer must be connected to the
other one.
NOTE
The compressor for temporary emergency
puncture repair has been tested and
approved by Volvo.
Taking out the emergency puncture
repair kit
The emergency puncture repair kit, with compressor and tools, is located under the floor in
the cargo area.
1. Fold away the rear edge of the floor mat,
forward from the back.
2. Lift up the emergency puncture repair kit.
12 V-sockets for the compressor are located
by the centre console in the front, by the rear
seat and in the cargo area, see pages 62, 76
190
Overview
* Option/accessory, for more information, see Introduction.
Label, maximum permitted speed
Switch
Cable
Bottle holder (orange cap)
Protective cap
Pressure reducing valve
Air hose
Sealing fluid bottle
Pressure gauge
07 Wheels and tyres
Emergency puncture repair*
Sealing punctured tyres
1. Detach the label for maximum permitted
speed (which is fitted on one side of the
compressor) and affix it to the steering
wheel.
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has
been used. Volvo recommends that you
visit an authorised Volvo workshop for
inspection of the sealed tyre (maximum
driving distance is 200 km). The staff there
can determine whether or not the tyre can
be repaired or if it needs to be replaced.
For information on the function of the parts, see
preceding illustration.
WARNING
The sealing fluid can irritate the skin. In the
case of contact with skin, wash away the
fluid with soap and water.
NOTE
Do not break the bottle's seal before use.
The seal is broken automatically when the
bottle is screwed in.
3. Unscrew the orange cap and unscrew the
bottle's stopper.
4. Screw the bottle into its holder.
WARNING
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
5. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the
bottom of the thread on the tyre's air
valve.
2. Check that the switch is in position 0 and
locate the cable and the air hose.
07
}}
* Option/accessory, for more information, see Introduction.
191
07 Wheels and tyres
Emergency puncture repair*
WARNING
Do not leave children in the car without
supervision when the engine is running.
6. Plug the cable into the 12 V socket and
start the car.
NOTE
If the compressor is connected to one of
the two 12 V sockets, no other current
consumer must be connected to the other
one.
NOTE
When the compressor starts, the pressure
can increase up to 6 bar but the pressure
drops after approximately 30 seconds.
7. Flick the switch to position I.
WARNING
07
192
Never stand next to the tyre when the
compressor is running. If cracks or
unevenness arise then the compressor
must be switched off immediately. The
journey should not be continued. Contacting an authorised tyre centre is recommended.
8. Inflate the tyre for 7 minutes.
IMPORTANT
2. Read the tyre pressure on the pressure
gauge.
Risk of overheating. The compressor must
not run for more than 10 minutes.
3. If it is below 1.3 bar then the tyre is insufficiently sealed. The journey should not
be continued. Contact a tyre centre.
9. Switch off the compressor to check the
pressure on the pressure gauge. Minimum pressure is 1.8 bar and
maximum is 3.5 bar.
4. If the tyre pressure is higher than 1.3 bar
then the tyre must be inflated to the pressure specified on the tyre pressure label.
Release air using the pressure reducing
valve if the tyre pressure is too high.
WARNING
If the pressure is below 1.8 bar then the
hole in the tyre is too big. The journey
should not be continued. Contacting an
authorised tyre centre is recommended.
10. Switch off the compressor and unplug the
cable from the 12 V socket.
11. Detach the hose from the tyre valve and
fit the valve cap.
12. As soon as possible, drive
approximately 3 km at a maximum speed
of 80 km/h so that the sealing fluid can
seal the tyre.
Rechecking the repair and pressure
1. Reconnect the equipment.
* Option/accessory, for more information, see Introduction.
WARNING
Do not unscrew the bottle, it is equipped
with a reverse catch to prevent leakage.
5. Switch off the compressor. Detach the air
hose and cable. Refit the dust cap.
07 Wheels and tyres
Emergency puncture repair*
NOTE
The sealing fluid bottle and the hose must
be replaced after use. Volvo recommends
that this replacement is performed by an
authorised Volvo workshop.
WARNING
Check the tyre pressure regularly.
6. Return the emergency puncture repair kit
to the cargo area.
7. Volvo recommends that you drive to the
nearest authorised Volvo workshop for
the replacement/repair of the damaged
tyre. Advise the workshop that the tyre
contains sealing fluid.
WARNING
You should not drive faster than 80 km/h
after the emergency tyre repair kit has
been used. Volvo recommends that you
visit an authorised Volvo workshop for
inspection of the sealed tyre (maximum
driving distance is 200 km). The staff there
can determine whether or not the tyre can
be repaired or if it needs to be replaced.
Inflating the tyres
The car's original tyres can be inflated by the
compressor.
1. The compressor must be switched off.
Make sure that the switch is in position 0
and locate the cable and air hose.
2. Unscrew the wheel's dust cap and screw
in the air hose valve connection to the
bottom of the thread on the tyre's air
valve.
Do not leave children in the car without
supervision when the engine is running.
6. Switch off the compressor. Detach the air
hose and cable.
Changing the sealing fluid canister
Replace the bottle when the expiration date
has passed. Treat the old bottle as environmentally hazardous waste.
WARNING
Inhaling car exhaust fumes can result in
danger to life. Never leave the engine running in sealed areas or areas that lack sufficient ventilation.
4. Start the compressor by flicking the
switch to position I.
5. Inflate the tyre to the pressure specified
on the tyre pressure label. (Release air
using the pressure reducing valve if the
tyre pressure is too high.)
7. Refit the dust cap.
WARNING
3. Connect the cable to one of the car's
12 V sockets and start the car.
IMPORTANT
Risk of overheating. The compressor must
not run for more than 10 minutes.
WARNING
The bottle contains 1.2-Ethanol and natural rubber-latex.
Harmful if ingested. Could result in allergic
reaction in the event of skin contact.
07
Avoid contact with the skin and eyes.
Store out of the reach of children.
* Option/accessory, for more information, see Introduction.
193
07 Wheels and tyres
Emergency puncture repair*
NOTE
Leave the container at a collection point
for storing dangerous waste.
07
194
* Option/accessory, for more information, see Introduction.
07 Wheels and tyres
07
195
Cleaning................................................................................................ 198
Touching up paintwork......................................................................... 202
Rustproofing......................................................................................... 204
196
CAR CARE
08 Car care
Cleaning
Washing the car
Wash the car as soon as it becomes dirty.
Wash the car in a car wash with oil separator.
Use car shampoo.
•
•
•
•
08
198
Remove bird droppings from the paintwork as soon as possible. Bird droppings
contain chemicals that affect and discolour paintwork very quickly. An authorised
Volvo workshop is recommended for the
removal of any discoloration.
Hose down the underbody.
Rinse the whole car until the loose dirt
has been removed in order to reduce the
risk of scratches from washing. Do not
spray directly onto the locks.
If necessary, use cold degreasing agent
on very dirty surfaces. Note that the surfaces must not then be warmed up by the
sun!
•
Wash using a sponge, car shampoo and
plenty of lukewarm water.
•
Clean the wiper blades with a lukewarm
soap solution or car shampoo.
•
Dry the car using a clean, soft chamois or
a water scraper. If you avoid allowing
water droplets to dry in strong sunlight
then the risk of water stains that may
need to be polished away is reduced.
WARNING
Always have the engine cleaned by a
workshop. There is a risk of fire if the
engine is hot.
NOTE
Wash the wiper blades and windscreen
regularly with lukewarm soap solution or
car shampoo.
Do not use any strong solvents.
IMPORTANT
Dirty headlamps have impaired functionality. Clean them regularly, when refuelling
for example.
Do not use any corrosive cleaning agents
but use water and a non-scratching
sponge instead.
NOTE
Outside lighting such as headlamps, fog
lamps and rear lamps may temporarily
have condensation on the inside of the
lens. This is a natural phenomenon, all outside lighting is designed to withstand this.
Condensation is normally vented out of the
lamp when it has been switched on for a
time.
Cleaning the wiper blades
Asphalt, dust and salt residue on wiper
blades, as well as insects, ice etc. on the
windscreen, impair the service life of wiper
blades.
Removing bird droppings
Wash away bird droppings from the paintwork as soon as possible. Bird droppings
contain chemicals that affect and discolour
paintwork very quickly. This discoloration can
only be removed by a specialist.
Chromed wheels
IMPORTANT
Rim cleaning agents can cause stains on
chrome-plated wheels. Wash using a
sponge, car shampoo and plenty of lukewarm water.
Automatic car washes
An automatic car wash is a simple and quick
way of washing the car, but it can never
replace a proper handwashing. The brushes
of an automatic car wash cannot reach everywhere.
08 Car care
Cleaning
IMPORTANT
Washing by hand is gentler to the paintwork than an automatic car wash. Paintwork is also more sensitive when it is new.
For this reason, handwashing is recommended during the first few months with a
new car.
Testing the brakes
IMPORTANT
Avoid waxing and polishing on plastic and
rubber.
WARNING
Always test the brakes after washing the
car, including the parking brake, to ensure
that moisture and corrosion do not attack
the brake linings and reduce braking performance.
High-pressure washing
When using high-pressure washing, use
sweeping movements and make sure that the
nozzle does not come closer than 30 cm to
the surface of the car (the distance applies to
all exterior parts).
IMPORTANT
Rinse the entire car to remove loose dirt.
When using a pressure washer: Make sure
that the nozzle of the pressure washer is
not closer than 30 cm to the bodywork. Do
not spray directly onto the locks.
Lightly depress the brake pedal now and then
when driving long distances in rain or slush.
This heats and dries the brake pads. Do the
same thing after starting in very damp or cold
weather.
Exterior plastic, rubber and trim
components
A special cleaning agent available from Volvo
dealers is recommended for the cleaning and
care of coloured plastic parts, rubber and trim
components (such as glossy trim mouldings).
When using such a cleaning agent the
instructions must be followed carefully.
When using degreasant on plastic and
rubber, only rub with light pressure if it is
necessary. Use a soft washing sponge.
Polishing glossy trim mouldings could
wear away or damage the glossy surface.
Polishing agent that contains abrasive
must not be used.
Polishing and waxing
Polish and wax the car if the paintwork is dull
or to give the paintwork extra protection.
The car does not need to be polished until it
is at least one year old. However, the car can
be waxed before this time. Do not polish or
wax the car in direct sunlight.
Wash and dry the car thoroughly before you
begin polishing or waxing. Clean off asphalt
and tar stains using tar remover or white spirit. More stubborn stains can be removed
using fine rubbing paste designed for car
paintwork.
Polish first with a polish and then wax with
liquid or solid wax. Follow the instructions on
the packaging carefully. Many preparations
contain both polish and wax.
08
}}
* Option/accessory, for more information, see Introduction.
199
08 Car care
Cleaning
IMPORTANT
Only paint treatment recommended by
Volvo should be used. Other treatment
such as preserving, sealing, protection,
lustre sealing or similar could damage the
paintwork. Paintwork damage caused by
such treatments is not covered by Volvo
warranty.
Cleaning the interior
Only use cleaning agents and car care products recommended by Volvo. Clean regularly
and follow the instructions included with the
car care product.
Vacuuming is important prior to using cleaning agents.
Carpets and cargo area
Water-repellent coating*
Never use products such as car
wax, degreaser or similar on glass
surfaces as this could ruin their
water-repellent properties.
Take care when cleaning so as not to damage the glass surface.
To avoid damaging glass surfaces when
removing ice – only use plastic ice scrapers.
There is natural wear of the water-repellent
coating.
NOTE
08
200
Treatment with a special finishing agent
available from Volvo dealers is recommended in order to maintain the waterrepellent properties. This should be used
first after three years and then each year.
Remove inlaid carpets for separate cleaning
of the floor carpet and the inlaid carpets. Use
a vacuum cleaner to remove dust and dirt.
Each inlay mat is secured with pins.
–
Take hold of the inlay mat at each pin and
lift the mat straight up.
Fit the inlay mat in place by pressing it in at
each pin.
WARNING
Before setting off check that the inlaid mat
in the driver area is firmly affixed and
secured in the bosses in order to avoid
getting caught adjacent to and under the
pedals.
A special textile cleaner is recommended for
stains on the floor mat after vacuuming. Floor
mats should be cleaned with agents recommended by your Volvo dealer!
* Option/accessory, for more information, see Introduction.
Treatment of stains on textile
upholstery and headliner
A special fabric cleaning agent, available from
authorised Volvo dealers, is recommended to
avoid impairing the fire retardant qualities of
the upholstery.
IMPORTANT
Sharp objects and Velcro may damage the
fabric upholstery.
Treating stains on leather upholstery
Volvo's leather upholstery is chromium-free
and is treated to preserve its original appearance.
Leather upholstery ages and acquires a beautiful patina over time. The leather is refined
and processed so that it retains its natural
characteristics. It is given a protective coating, but regular cleaning is required in order
to maintain both characteristics and appearance. Volvo offers a comprehensive product
for the cleaning and treatment of leather
upholstery which, when used in accordance
with the instructions, preserves the leather's
protective coating. After a period of use the
natural appearance of the leather will nevertheless emerge, depending more or less on
the surface texture of the leather. This is a
08 Car care
Cleaning
natural maturing of the leather and shows
that it is a natural product.
Protective treatment of leather
upholstery
Group 1 (ink, wine, coffee, milk, sweat and
blood)
To achieve best results Volvo recommends
cleaning and the application of protective
cream once to four times per year (or more if
necessary). The Volvo Leather Care kit is
available from your Volvo dealer.
Vacuuming is important prior to using leather
care agents.
–
1. Pour a small amount of the protective
cream on the felted cloth and massage in
a thin layer of cream with gentle circular
movements on the leather.
Group 2 (fats, oils, sauces and chocolate)
IMPORTANT
•
•
Certain items of coloured clothing (for
example, jeans and suede garments)
may stain the upholstery.
Never use strong solvents. Such products may damage fabric, vinyl and
leather upholstery.
2. Polish with an absorbent paper or cloth.
The leather has now been given improved
protection against stains and improved UV
protection.
1. Use a soft brush to remove the dirt.
IMPORTANT
Sharp objects may damage the leather,
(e.g. rings).
Washing instructions for the leather
steering wheel
•
Remove dirt and dust with a soft premoistened sponge and neutral soap.
•
3. Dab accurately with the sponge on the
stains. Allow the sponge to absorb the
stain. Do not rub.
Leather needs to breathe. Never cover
the leather steering wheel with protective
plastic.
•
4. Wipe off with soft paper or a cloth and
allow the leather to dry completely.
Use natural oils. Volvo's leather care
agents are recommended for best results.
If the steering wheel has stains:
2. Work the dirt away with gentle circular
movements.
1. Same procedure as for group 1.
2. Allow the leather to dry for 20 minutes
before use.
Washing instructions for leather
upholstery
1. Pour the leather cleaner on the dampened sponge and squeeze out a strong
foam.
Use a soft cloth or sponge. Mix a 5%
ammonia solution. (For blood stains, use
a solution of 2 dl water and 25g salt.)
Group 3 (dry dirt, dust)
2. Same procedure as for group 1.
Treating stains on interior plastic, metal
and wood parts
A special cleaning agent, available from Volvo
dealers, is recommended for cleaning interior
parts and surfaces. Do not scrape or rub
stains. Never use strong stain removers.
Cleaning seatbelts
Use water and a synthetic detergent. A special textile cleaning agent is available from
your Volvo dealer. Make sure the seatbelt is
dry before allowing it to retract.
08
201
08 Car care
Touching up paintwork
Paintwork
Stone chips and scratches
Repairing minor paint damage such as
stone chips and scratches
Paint is an important part of the car's rustproofing and should therefore be checked
regularly. To avoid the onset of rust, damaged paintwork should be rectified immediately. The most common types of paintwork
damage are stone chips, scratches, and
marks on the edges of wings, doors and
bumpers.
1. Apply a piece of masking tape over the
damaged surface. Then remove the tape
to remove any loose paint.
If the damage has reached down to a
metal surface (sheet steel), it is preferable
to use a primer. In the event of damage to
a plastic surface, an adhesive primer
should be used for better results - spray
into the spray can's cap and brush thinly.
G020345
Colour code (Paint code)
Before work is started, the car must be clean
and dry as well as at a temperature above
15 °C.
Materials
•
primer1 - for e.g. plastic-clad bumpers
there are special adhesive primers available in spray cans
•
base coat and clear coat - are available in
spray cans or as touch-up pens/sticks2
•
•
masking tape
Data plate.
Code for car's colour
It is important that the correct colour is used.
For product decal location, see page 286.
08
1
2
202
fine sand paper1.
If required.
Follow the instructions that are included with the package for the touch-up pen/stick.
2. A light sanding with very fine abrasive
material can be performed locally before
painting if necessary (e.g. if there are
rough edges). Clean the surface thoroughly and allow to dry.
3. Stir the primer well and apply using a fine
brush, matchstick or similar. Finish with
base coat and clear coat once the primer
has dried.
4. For scratches, proceed as above, but
mask around the damaged area to protect the undamaged paintwork.
08 Car care
Touching up paintwork
NOTE
If the stone chip has not penetrated down
to the meal and an undamaged layer of
paint remains in place, fill in with base coat
and clear coat as soon as the surface has
been cleaned.
08
203
08 Car care
Rustproofing
Inspection and maintenance
Your car has already received a thorough and
complete rustproofing at the factory. Parts of
the body are made of galvanised sheet metal.
The underbody is protected by a wear-resistant anti-corrosion compound. A thin, penetrating rustproofing fluid was sprayed into the
members, cavities and closed sections.
Maintain the car's rustproofing.
•
Keep the car clean. Hose down the
underbody. If using a pressure washer,
keep the nozzle at least 30 cm from the
painted surfaces.
•
Regularly check and touch-up the rustproofing treatment as necessary.
The car's rustproofing does not normally
require treatment for approximately 12 years.
After this period, it should be treated at threeyear intervals. If the car needs further treatment, Volvo recommends that you engage an
authorised Volvo workshop for assistance.
08
204
08 Car care
08
205
Volvo service.........................................................................................
Self-maintenance..................................................................................
Bonnet and engine compartment.........................................................
Oils and fluids.......................................................................................
Wiper blades.........................................................................................
Battery...................................................................................................
Replacing bulbs....................................................................................
Fuses.....................................................................................................
206
208
209
211
213
218
220
223
230
MAINTENANCE AND SERVICE
09 Maintenance and service
09
Volvo service
Volvo service programme
Before the car left the factory, it was thoroughly test driven. It was checked again in
accordance with Volvo Car Corporation regulations before it was handed over to you.
To keep your Volvo as safe and reliable as
possible, follow the Volvo service programme
specified in the Service and Warranty Booklet. Volvo also recommends that you engage
an authorised Volvo workshop to perform the
service and maintenance work. Volvo workshops have the personnel, special tools and
service literature to guarantee the highest
quality of service.
IMPORTANT
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklet.
Special service measures
Certain service measures which affect the
car's electrical system can only be performed
using electronic equipment specially developed for your car. Similarly, Volvo recommends that you contact an authorised Volvo
workshop before starting or performing service work that affects the electrical system.
208
09 Maintenance and service
Self-maintenance
Before starting work on the car
Check regularly
Battery
Check the following at regular intervals, for
example, when refuelling:
Check that the battery cables are correctly
connected and tightened.
•
Never disconnect the battery when the
engine is running (e.g. if replacing the battery).
Coolant – The level must be between the
MIN and MAX marks on the expansion
tank.
•
Engine oil – The level must be between
the MIN and MAX marks.
•
Power steering fluid – The level must be
between the MIN and MAX marks.
•
Washer fluid – The reservoir should be
well filled. Fill washer fluid with antifreeze
at temperatures around freezing point.
•
Brake and clutch fluid – The level must be
between the MIN and MAX marks.
The battery contains acid that is both corrosive and toxic. It is therefore important to
handle the battery in an environmentally correct manner. Let your Volvo dealer assist you.
WARNING
Lifting the car
NOTE
Volvo recommends only using the jack that
belongs to the car model in question. If a
jack is selected other than the one recommended by Volvo, follow the instructions
supplied with the equipment.
WARNING
The ignition system has very high voltage
and output. The voltage in the ignition system is highly dangerous. The ignition must
therefore always be switched off for work
in the engine compartment.
Remember that the radiator fan (located at
the front of the engine compartment,
behind the radiator) may start automatically some after the engine has been
switched off.
Do not touch the spark plugs or ignition
coils when the ignition is on or the engine
is hot.
Always have the engine cleaned by a
workshop. There is a risk of fire if the
engine is hot.
G026997
Never use a quick charger to charge the battery. The battery cables must be disconnected when charging the battery.
09
Jacking points for the jack that belongs to the
car.
}}
209
09 Maintenance and service
09
Self-maintenance
Lifting points.
If the car is raised with a workshop jack then
it must be positioned under one of the lifting
points. Ensure that the jack is positioned so
that the car cannot slide off the jack. Always
use axle stands or the like.
If the car is raised with a two-pillar workshop
lift, ensure that the front and rear lift arms are
fixed under the lifting points.
210
09 Maintenance and service
Bonnet and engine compartment
Opening the bonnet
09
WARNING
G026995
Close the bonnet by placing your hand on
its top and pressing down. Do not close it
by holding the grille. Engine components
on the inside could injure your fingers.
1. Pull the handle on the far left (or right if
the car is RHD) under the instrument
panel. You will hear when the lock releases.
2. Insert your hand to the right under the
front edge of the bonnet (below the grille).
3. Press up the safety catch handle.
4. Release the handle and open the bonnet.
WARNING
Check that the bonnet locks properly when
closed.
}}
211
09 Maintenance and service
09
Bonnet and engine compartment
G027074
Engine compartment
Reservoir for brake and clutch fluid
(located on the driver's side)
Relay and fuses
Air filter. (The cover has a different design
depending on engine variant.)
Radiator
Engine oil dipstick
Engine oil filling
Washer fluid reservoir
Reservoir for power steering fluid (location depends on engine variant.)
212
Expansion tank, cooling system
Chassis data plate
Battery (in the cargo area)
Air conditioning system
Troubleshooting and repair
The air conditioning system contains fluorescent tracing agents. Use ultraviolet light when
looking for leaks.
Volvo recommends that you contact an
authorised Volvo workshop.
WARNING
The air conditioning system contains pressurised refrigerant R134a. This system
must only be serviced and repaired by an
authorised workshop.
09 Maintenance and service
Oils and fluids
Checking the engine oil
09
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory. The choice of oil
has been made very carefully with regard
to service life, starting characteristics, fuel
consumption and environmental impact.
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil for both filling and oil change,
otherwise you will risk affecting service life,
starting characteristics, fuel consumption
and environmental impact.
Volvo recommends:
When driving under adverse conditions, see
page 292.
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
Volvo recommends that oil changes are
carried out at an authorised Volvo workshop.
Volvo uses different systems for warning of
low/high oil level or low/high oil pressure.
Certain engine variants have an oil pressure
sensor, and then the combined instrument
panel's warning symbol for low oil pressure is
used. Other variants have an oil level sensor,
and then the driver is informed via the warning symbol in the centre of the instrument unit
as well as by display texts. Certain variants
}}
213
09 Maintenance and service
09
Oils and fluids
have both systems. Contact a Volvo dealer
for more information.
5. If the level is close to MIN then 0.5 litres
should be added. If the level is significantly below, then an additional amount
is required.
Checking the oil
Change the engine oil and oil filter in accordance with the intervals specified in the Service and Warranty Booklet.
6. If required, check the level again, do it
after driving a short distance. Then repeat
steps 1 - 4.
Using oil of a higher than specified grade is
permitted. If the car is driven in adverse conditions, Volvo recommends using an oil of a
higher grade, see page 292.
WARNING
Never fill above the MAX mark. The level
should never be above MAX or below MIN
as this could lead to engine damage.
For capacities, see page 293 and onwards.
Volvo recommends checking the oil level
every 2 500 km. The most accurate measurements are made on a cold engine before starting. The measurement will be inaccurate if
taken immediately after the engine is
switched off. The dipstick will indicate that
the level is too low because the oil has not
had time to flow down into the oil sump.
G020336
Checking the oil level in a new car is especially important before the first scheduled oil
change.
The oil level must be within the area marked on
the dipstick.
Measurement and filling if required
1. Ensure that the car is level. After switching off the engine it is important to wait
5 minutes to allow the oil time to run back
to the sump.
2. Pull up and wipe the dipstick.
3. Re-insert the dipstick.
4. Pull it out and check the level.
214
WARNING
Do not spill oil onto the hot exhaust manifold due to the risk of fire.
09 Maintenance and service
Oils and fluids
Washer fluid, topping up
Checking and topping up the coolant
09
See capacities on page 294.
Check the coolant regularly
The level must be between the MIN and MAX
marks on the expansion tank. If the system is
not filled sufficiently, high local temperatures
could occur, causing a risk of damage
(cracks) to the cylinder head. Top up the
coolant when the level falls to the MIN mark.
Location of washer fluid reservoir.
The windscreen and headlamp washers have
the same reservoir. Use washer fluid with
antifreeze during the winter to avoid freezing
in the pump, reservoir and hoses. See
capacities on page 294.
NOTE
Mix concentrated washer fluid with water
before filling.
TIP! Clean the wiper blades when topping up
washer fluid.
G027087
G027097
WARNING
Coolant can be very hot. If the coolant
requires topping up when the engine is at
operating temperature, unscrew the
expansion tank cap slowly to gently
release the overpressure.
When topping up the coolant, follow the
instructions on the packaging. It is important
that the mixture of coolant concentrate and
water is correct for the prevailing weather
conditions. Never top up with water only. The
risk of freezing increases with both too little
and too much coolant concentrate.
IMPORTANT
Always use coolant with anti-corrosion
agent as recommended by Volvo. New
cars are filled with coolant that can withstand temperatures down to approximately ca -35 °C.
}}
215
09 Maintenance and service
Oils and fluids
•
A high content of chlorine, chlorides
and other salts may cause corrosion in
the cooling system.
•
Always use coolant with anti-corrosion
agent as recommended by Volvo.
•
Ensure that the coolant mixture is 50%
water and 50% coolant.
•
Mix the coolant with approved quality
tap water. In the event of any doubt
about water quality, used ready-mixed
coolant in accordance with Volvo recommendations.
•
When changing coolant/replacing
cooling system components, flush the
cooling system clean with approved
quality tap water or flush with readymixed coolant.
•
The engine must only be run with a
well-filled cooling system. Otherwise,
temperatures that are too high may
occur resulting in the risk of damage
(cracks) in the cylinder head.
For capacities and for standards regarding
water quality, see the table under Fluids and
lubricants on page 294.
1
216
Location dependent on whether car is left or right-hand drive.
Checking and topping up the brake
and clutch fluid
WARNING
If the brake fluid is under the MIN level in
the brake fluid reservoir, do not drive further before topping up the brake fluid.
The reason for the loss of brake fluid must
be investigated.
Checking and topping up the power
steering fluid
FULL
ADD
Brake and clutch fluid have a common reservoir1. The fluid level must be between the
MIN and MAX marks. Check the level regularly. Change the brake fluid every other year
or at every other regular service.
G026991
IMPORTANT
G000000
09
See the capacities and recommended fluid
grade on page 294.
The fluid should be changed annually on cars
driven in conditions requiring hard, frequent
braking, such as driving in mountains or tropical climates with high humidity.
NOTE
Check the level frequently.
09 Maintenance and service
Oils and fluids
09
Check the level frequently. The fluid does not
require changing. The level must lie between
the ADD and FULL marks. See the capacities
and recommended grade on page 294.
NOTE
If a fault should arise in the power steering
system or if the car is without power and
must be towed, it can still be steered.
However, the steering will be much heavier
than normal and it will require more effort
to turn the steering wheel.
217
09 Maintenance and service
09
Wiper blades
Wiper blades
Cleaning
For cleaning wiper blades and windscreen,
see page 198.
IMPORTANT
Check the wiper blades regularly. Neglected maintenance shortens the service
life of the wiper blades.
Replacing the wiper blades, windscreen
NOTE
The wiper blades are different lengths. The
blade on the driver's side is longer than on
the other side.
1. Fold out the wiper arm and grasp the
wiper blade.
2. Press in the ribbed spring catch on the
wiper blade while lifting it off at the arm
extension.
3. Fit the new blade in reverse order and
check that it is properly secured.
G026959
Changing the rear window wiper blade
1. Fold out the wiper arm.
218
09 Maintenance and service
Wiper blades
09
2. Remove the wiper blade by moving it
up/out (see illustration) towards the tailgate.
3. Press the new wiper blade into position.
4. Check that the blade is firmly installed.
219
09 Maintenance and service
Battery
09
Operation
The starter battery is a traditional 12 V battery.
The service life and function of the battery is
influenced by factors such as the number of
starts, discharging, driving style, driving conditions and climatic conditions.
•
Never disconnect the battery when the
engine is running.
•
Check that the cables to the battery are
correctly connected and properly tightened.
WARNING
220
•
The battery can generate oxyhydrogen
gas, which is highly explosive. A spark
can be formed if a jump lead is connected incorrectly, and this can be
enough for the battery to explode.
•
The battery contains sulphuric acid,
which can cause serious burns.
•
If sulphuric acid comes into contact
with eyes, skin or clothing, flush with
large quantities of water. If acid
splashes into the eyes - seek medical
attention immediately.
NOTE
The life of the battery is shortened if it
becomes discharged repeatedly.
The life of the battery is affected by several
factors, including driving conditions and
climate. Battery starting capacity decreases gradually with time and therefore
needs to be recharged if the car is not
used for a longer time or when it is only
driven short distances. Extreme cold further limits starting capacity.
To maintain the battery in good condition,
at least 15 minutes of driving/week is recommended or that the battery is connected to a battery charger with automatic
trickle charging.
A battery that is kept fully charged has a
maximum service life.
Symbols on the battery
Use protective goggles.
Further information in the
owner's manual for the
car.
Store the battery out of
the reach of children.
IMPORTANT
Only a traditional battery charger should
ever be used when charging the battery.
The battery contains corrosive acid.
09 Maintenance and service
Battery
Avoid sparks and naked
flames.
Replacing the main battery
Removal
09
4. Detach the black negative cable.
WARNING
Connect and remove the positive and negative cables in the correct order.
5. Detach the red positive cable.
Risk of explosion.
6. Detach the ventilation hose from the battery.
7. Release the clamp securing the battery.
8. Remove the battery.
Must be taken for recycling.
Fitting
1. Remove the remote control key from the
ignition switch.
An expended battery must be recycled in
an environmentally safe manner as it contains lead.
2. Wait at least 5 minutes before touching
any electrical terminals.
> The car's electrical system needs to
store the necessary information to the
control modules.
WARNING
REMOVAL OF BATTERY
DISCONNECT
O CABLE FIRST
xxxx xxxxx xx xxxxx
xxxx xxxxx xx xxxxx
xxxx xxxxx xxxxx
xxxx xx
+
-
3. Unscrew the bracket and cover over the
battery
DRAIN PIPE
G027076
NOTE
1. Fit the battery into position.
}}
221
09 Maintenance and service
09
Battery
2. Tighten the clamp that holds the battery.
3. Connect the ventilation hose.
> Check that it is correctly connected to
both battery and outlet in the body.
4. Connect the red positive cable.
5. Connect the black negative cable.
6. Fit the cover and bracket.
222
09 Maintenance and service
Replacing bulbs
Bulb specifications can be found on page
299.
The following list contains locations of bulbs
and other light sources that are specialised,
or are unsuitable for changing for some other
reason, except at a workshop:
•
active xenon headlamps - ABL (xenon
lamps)
•
Daytime running lights (DRL) in the
bumper
•
Direction indicators, door mirror and
approach lighting
•
•
•
•
•
Reading lamps and glovebox lighting
General interior lighting in the roof
Position lamps, rear
Brake light
high-level brake light.
In the event of a fault in the daytime running
lights (DRL) in the bumper the whole lamp
insert is replaced.
In the event of a fault in the rear position
lamps or brake lights the whole rear light
cluster is replaced.
WARNING
Changing front bulbs
On cars with Xenon headlamps, the
replacement of Xenon lamps must be carried out at a workshop - an authorised
Volvo workshop is recommended. Working
with Xenon lamps demands extreme caution because the headlamp is equipped
with a high voltage unit.
IMPORTANT
Never touch the glass part of the bulbs
with your fingers. Grease and oil from your
fingers are vaporised by the heat, coating
the reflector and then causing damage.
NOTE
If an error message remains after the broken bulb has been replaced then we recommend that you visit an authorised Volvo
workshop.
NOTE
Outside lighting such as headlamps, fog
lamps and rear lamps may temporarily
have condensation on the inside of the
lens. This is a natural phenomenon, all outside lighting is designed to withstand this.
Condensation is normally vented out of the
lamp when it has been switched on for a
time.
G027081
General
09
The entire lamp insert must first be removed
when replacing dipped beam, main beam and
parking lamp bulbs. To replace one of these
bulbs, do the following and then consult the
instructions for the specific lamp.
Removing the lamp housing:
1. Switch off all lights and turn the remote
control key to position 0.
2. Open the bonnet.
3. Release the insert by pulling up the two
lock pins holding it in place.
4. Lift the insert straight out.
}}
223
09 Maintenance and service
09
Replacing bulbs
Location of bulbs in front lamp
IMPORTANT
Dipped beam, halogen
Do not pull the electrical cable, only the
connector
5. Unplug the connector by first pressing in
the catch from underneath and then pulling it up a bit from above.
Dipped beam
Main beam
Direction indicators
G027083
Parking/position lamps
Refit the headlamp insert in reverse order.
Check that the lock pins are correctly situated.
Side marker lamps
G027088
G027082
6. Lift out the entire headlamp insert and
place it on a soft surface so as not to
damage the lens.
1. Undo the outer cover by turning it anticlockwise.
2. Unplug the connector.
3. Disconnect the spring clamp. First push
to the right so that the spring clamp disconnects, then out and down.
4. Pull out the lamp.
5. Fit the new bulb. It can only fit in one
position.
6. Press the clamp spring upwards and a little to the left so that it secures in its
catch.
7. Press the connector back in place.
224
09 Maintenance and service
Replacing bulbs
8. Screw the cover back into place; the
marking HAUT should be at the top.
5. Press the clamp spring upwards and a little to the left so that it secures in its
catch.
4. Fit the bulb holder back in place and turn
clockwise.
Main beam
6. Press the connector back in place and
refit the cover.
Direction indicators
Halogen headlamps
09
G027085
G027089
Side marker lamps and position/
parking lamps
G028409
The bulbs are housed in bayonet holders.
1. Undo the outer cover by pulling it straight
out and then unplug the connector.
2. Disconnect the spring clamp. First push
to the right so that the spring clamp disconnects, then out and down.
3. Pull out the lamp.
4. Fit the new bulb. It can only fit in one
position.
1. Turn the bulb holder anticlockwise and
remove.
The bulbs are housed in bayonet holders.
2. Press in the bulb, turn anticlockwise and
remove.
1. Turn the bulb holder anticlockwise and
remove.
3. Fit the new bulb by pressing it into the
recess and then turning clockwise.
2. Pull the bulb straight out.
3. Fit the new bulb by carefully pressing it
into the recess.
}}
225
09 Maintenance and service
09
Replacing bulbs
Bulbs in rear lamp cluster
Direction indicators
Reversing lamp
226
09 Maintenance and service
Replacing bulbs
09
Bulb replacement
1. Switch off all lights and turn the remote
control key to position 0.
7. Loosen the extra length of cable for better accessibility.
14. Refit the insert against the bolt holes.
Press the insert into place.
2. Lower the bottom of the tailgate and
open the floor hatch. (If the car is equipped with a grocery bag holder* undo the
holder's retaining straps.)
8. Place the insert on a soft surface so as
not to scratch the glass.
15. Tighten the nuts.
3. Remove the corner piece.
4. Open the hatch in the side panel by pulling the catch up and towards you.
5. Take spanner no. 10 out of the tool kit
and undo the nuts.
6. Pull the entire insert straight back.
9. Turn the bulb holder anticlockwise and
pull it out.
16. Refit the side panel and corner piece.
10. Turn the bulb anticlockwise in order to
loosen it.
11. Replace the bulb.
12. Refit the bulb holder in the recess and
turn clockwise.
13. Press back the extra length of cable.
}}
* Option/accessory, for more information, see Introduction.
227
09 Maintenance and service
Replacing bulbs
Rear fog lamp
Number plate lighting
Courtesy lighting
1. Insert a slotted screwdriver as indicated
by the arrow in the illustration.
1. Switch off all lights and turn the remote
control key to position 0.
2. Prise out the lamp insert.
2. Remove the screws with a screwdriver.
There is courtesy lighting under the instrument panel on the driver and passenger
sides.
3. Turn the bulb holder anticlockwise to
loosen it.
3. Carefully detach the entire lamp housing
and withdraw it.
4. Turn the bulb anticlockwise and lift the
bulb out.
4. Replace the bulb.
G027079
09
5. Replace the bulb.
228
5. Refit the entire lamp housing and screw it
into place.
1. Insert a screwdriver and gently turn so
that the lens detaches.
2. Remove the blown bulb.
3. Fit a new bulb.
4. Refit the lens.
09 Maintenance and service
Replacing bulbs
Bulb in cargo area
Vanity mirror lighting
1. Insert a screwdriver and gently turn so
that the lamp housing comes loose.
Removal of lamp lens
2. Remove the blown bulb.
3. Fit a new bulb. Check that the bulb lights.
4. Refit the lamp housing.
09
1. Insert a screwdriver under the lamp lens
and gently prize up the lock lugs on the
edge.
2. Snap off the lamp lens.
3. Use needle-nose pliers to pull the bulb
straight out to the side and replace with a
new one. Note! - Do not pinch hard with
the pliers. Otherwise the lamp lens could
then be crushed.
Attaching the lamp lens
1. Refit the lamp lens.
2. Press it into place.
229
09 Maintenance and service
09
Fuses
G032337
General
Cable routing may vary slightly due to engine variant. However, the fuse boxes listed are in the same positions.
All electrical functions and components are
protected with a number of fuses to protect
your car's electrical system from damage by
short-circuits or overloads.
The fuses are in five different locations in the
car:
Relay/fuse box in the engine compartment.
Fuse box in the passenger compartment
within the sound barrier on the driver's
side.
230
Fuse box in the passenger compartment
at dashboard end on driver's side.
Fuse box in cargo area.
Fuse box in cargo area - Executive*.
If an electrical component or function does
not work, this may be because the component's fuse was temporarily overloaded and
blew.
1. Look in the fuse diagram to locate the
fuse.
2. Pull out the fuse and check from the side
to see whether the curved wire has
blown.
3. If this is the case, replace it with a new
fuse of the same colour and amperage.
WARNING
Never use a foreign object, or a fuse with
an amperage higher than that specified
when replacing a fuse. This could cause
significant damage to the electrical system
and possibly lead to fire.
09 Maintenance and service
Fuses
09
There are a number of spare fuses in the
cover on the end face of the instrument
panel. There are also pliers which facilitate
the removal and fitting of fuses.
If the same fuse fails repeatedly then there is
a fault in the component. In which case,
Volvo recommends that you visit an authorised Volvo workshop for this to be checked.
}}
231
09 Maintenance and service
09
Fuses
G026972
Relay/fuse box in the engine compartment
232
1.
ABS
30 A
2.
ABS
30 A
3.
High-pressure washer, headlamps
35 A
4.
Parking heater*
25 A
5.
Auxiliary lamps*
20 A
6.
Starter motor relay
35 A
7.
Windscreen wipers
25 A
8.
Fuel pump
15 A
9.
Transmission control module
(TCM)
10.
Ignition coils (petrol), engine
control module (ECM), injection valves, (diesel)
20 A
Accelerator pedal sensor
(APM), AC compressor
10 A
11.
* Option/accessory, for more information, see Introduction.
15 A
12.
13.
Engine control module (ECM)
(petrol), injection valves (petrol), mass air flow sensor (petrol)
15 A
mass air flow sensor (diesel)
5A
Actuator motors, intake manifold (6-cyl.)
10 A
Electronic throttle module
(ETM), solenoid valve, SWIRL
(air mixing valve), fuel pressure regulator (diesel)
15 A
09 Maintenance and service
Fuses
14.
Lambda-sond (petrol)
20 A
Lambda-sond (diesel)
10 A
Crankcase ventilation heater
(petrol), AC connection (petrol), solenoid valves, ECM,
(petrol), glow heating control
(diesel)
15 A
16.
Dipped beam, left
20 A
17.
Dipped beam, right
20 A
18.
-
19.
Engine control module (ECM)
supply, engine relay
5A
20.
Position lamp
15 A
21.
Vacuum pump (petrol)
20 A
15.
09
-
}}
233
09 Maintenance and service
09
Fuses
G028412
Relay/fuse box in the passenger compartment within the sound barrier on the driver's side
234
1.
Seat heating, right side
15 A
9.
Brake lamp switch feed
2.
Seat heating, left side
15 A
10.
3.
Horn
15 A
4.
-
Combined instrument panel
(DIM), climate control (CCM),
parking heater, power driver's seat
10 A
5.
Infotainment system
11.
Front seat, rear seat and
refrigerator socket*
15 A
6.
-
-
12.
-
-
7.
-
-
13.
-
-
8.
Siren*
14.
-
-
10 A
5A
* Option/accessory, for more information, see Introduction.
5A
15.
ABS, DSTC
5A
16.
Electronic power steering
(ECPS)*, Active Xenon headlamps - ABL*, headlamp levelling*
10 A
17.
Daytime running lights (DRL)
left
7.5 A
18.
Daytime running lights (DRL)
right
7.5 A
19.
-
-
09 Maintenance and service
Fuses
20.
-
-
21.
Transmission control module
(TCM)
10 A
22.
Main beam, left
10 A
23.
Main beam, right
10 A
24.
-
-
25.
-
-
26.
-
-
27.
-
-
28.
Power passenger seat*, Rear
Seat Entertainment (RSE)*A
A
35.
-
-
36.
-
-
09
See also fuse 8 in the section entitled "Relay/fuse box in
the passenger compartment at dashboard end on driver's
side".
5A
29.
Fuel pump
7.5 A
30.
BLIS*
31.
-
-
32.
-
-
33.
Vacuum pump (petrol)
20 A
34.
Washer pump
15 A
5A
}}
* Option/accessory, for more information, see Introduction.
235
09 Maintenance and service
09
Fuses
G032316
Relay/fuse box in the passenger compartment at dashboard end on driver's side
A decal which specifies the positions and amperages of the fuses is located in the end box cover.
1.
Climate control system fan
30 A
7.
-
2.
Audio (amplifier)*
30 A
8.
3.
Power driver's seat*
25 A
Radio, CD player, Rear
Seat Entertainment
(RSE)*A
15 A
4.
Power passenger seat*
25 A
9.
5.
Control module, left front
door
Navigation display*, Navigation device MMM*
10 A
25 A
10.
Control module, right front
door
25 A
OBDII, light switch (LSM),
Steering Angle Sensor
(SAS), Steering Wheel
Module (SWM)
6.
236
* Option/accessory, for more information, see Introduction.
-
11.
12.
5A
Ignition switch, SRS-system, engine control module ECM (petrol) SRS
deactivation passenger
side (PACOS), electronic
immobiliser (IMMO),
Transmission control module (TCM)
7.5 A
General lighting, ceiling
(RCM) Upper electronic
module (UEM)
10 A
09 Maintenance and service
Fuses
A
13.
Sunroof*
15 A
14.
Telematics*, Bluetooth*
5A
15–
38.
-
09
-
See also fuse 28 in the section entitled "Relay/fuse box in
the passenger compartment within the sound barrier on
the driver's side".
}}
* Option/accessory, for more information, see Introduction.
237
09 Maintenance and service
09
Fuses
Fuses in the cargo area
238
1.
Reversing lamp
10 A
7.
Towing bracket wiring* (30feed)
15 A
2.
Position lamps, rear fog
lamp, cargo area lighting,
number plate lighting, lamps
in brake lighting
20 A
3.
Accessories (AEM)*
15 A
4.
-
8.
Electrical socket, cargo area
15 A
9.
Rear right door: Power window, power window lock
10.
Rear left door: Power window, power window lock
5.
REM electronics
10 A
11.
6.
-
-
-
14.
Rear air conditioning (A/C)*
15.
-
-
16.
-
-
20 A
17.
Infotainment system accessories*
20 A
18.
-
-
-
19.
Rear wiper
15 A
12.
-
-
20.
13.
Diesel filter heater
Towing bracket wiring* (15feed)
20 A
* Option/accessory, for more information, see Introduction.
15 A
15 A
5A
-
09 Maintenance and service
Fuses
21.
-
-
37.
Rear window defroster
20 A
22.
-
-
38.
Rear window defroster
20 A
23.
AWD
24.
-
-
25.
-
-
26.
Park Assist*
5A
27.
Main fuse: Towing bracket
wiring, parking assistance,
AWD
30 A
28.
Central locking system (PCL)
15 A
29.
Trailer lighting, left: Position
lamps, direction indicator*
25 A
30.
Trailer lighting, right: Brake
light, rear fog lamp, direction
indicator*
25 A
31.
Main fuse: Fuse 37, 38
40 A
32.
-
-
33.
-
-
34.
-
-
35.
-
-
36.
-
-
09
7.5 A
}}
* Option/accessory, for more information, see Introduction.
239
09 Maintenance and service
09
Fuses
Fuses in the cargo area - Executive*
The fuse box is located behind the cover
panel on the left-hand side.
240
1.
Relay, seat heating, rear seat,
Relay, massage seat, front
5A
2.
Seat heating, rear seat, left
15 A
3.
Seat heating, rear seat, right
15 A
4.
Ventilated seat front, Massage
seat front
10 A
5.
-
-
6.
-
-
* Option/accessory, for more information, see Introduction.
09 Maintenance and service
09
241
General..................................................................................................
Control panels, audio............................................................................
Audio system functions.........................................................................
Radio functions.....................................................................................
CD functions.........................................................................................
Menu structure – audio system.............................................................
Phone functions*...................................................................................
Menu structure – phone........................................................................
Bluetooth handsfree*............................................................................
RSE - Rear Seat Entertainment system - Dual Screen* .......................
242
* Option/accessory, for more information, see Introduction.
244
245
248
253
259
262
263
270
274
280
INFOTAINMENT SYSTEM
10 Infotainment system
General
Infotainment system
10
Infotainment is a system that integrates the
audio system and phone functions.
You can easily and conveniently use your
Infotainment system by means of the joint
control panel or the steering wheel keypad.
XC90 can be equipped with Dolby Surround
Pro Logic II1. This offers an optimal sound
experience very close to being there with a
broad, natural sound profile.
The system also allows your passengers to
use headphones* with separate audio
sources.
Dolby Surround Pro Logic II1
Dolby Surround Pro Logic II distributes the
two stereo audio channels to left, centre, right
and rear speakers. This provides a more realistic sound quality than that provided by
standard two-channel stereo.
Dolby Surround Pro Logic II and the
Dolby icon are trademarks of Dolby
Laboratories Licensing Corporation.
Dolby Surround Pro Logic II System
is manufactured under license from Dolby
Laboratories Licensing Corporation.
1
244
Applies to Premium Sound.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Control panels, audio
Audio controls
10
CD – shortcuts
PHONE - Phone On/Off/Standby
MENU – menu selection buttons
VOLUME - Volume (knob control)
MY KEY – programmable shortcut key for
your favourite function
CD and CD changer eject*
POWER - Audio On/Off
AM/FM-shortcut between FM1, FM2 and
AM
Display
ENTER - select in the menu, activate a
selection or access the folder structure
and start playback of audio files if there is
a disc containing audio files in the CD
player. For more information, see
page 259.
SELECTOR - select audio source (rotary
control)
SOUND – audio settings
EXIT/CLEAR – scroll back in the menu,
cancel a selection, put the phone in
standby mode, or erase the previous
character when entering text and numbers
SIM card holder
CD player and CD changer*
Seek/change tracks/stations or scroll forward and back when entering text and
digits
Station setting buttons/selecting CD
changer position* (1-6), number and character buttons for the phone and menu
shortcuts
IR* - receiver for remote controls
}}
* Option/accessory, for more information, see Introduction.
245
10 Infotainment system
Control panels, audio
Steering wheel keypad
10
Menus
Shortcuts
Menu options are numbered and can also be
selected directly with the keypad 1-6.
Audio – Phone*
My own shortcut button – MY KEY
Use MY KEY to store a favourite function in
the menu, e.g. TP.
G027112
–
The four buttons at the bottom of the steering
wheel keypad control both the radio and the
phone. The function of the respective button
depends on which system is active. The
steering wheel keypad can be used to adjust
volume, switch between preset stations and
change CD tracks. The two upper buttons in
the keypad (Yes and No) are used to answer
and end phone calls respectively. To change
between audio menu and phone menu, press
No.
Select the function in the menu to be
stored by holding MY KEY depressed for
more than two seconds.
When My Key stored. is shown in the display, the function has been stored.
–
Activate the function with a short press
on MY KEY.
Some infotainment system functions are controlled via a menu system. The current menu
level is shown at the top right of the display.
Menu options are shown in the middle of the
display.
Functions that can be stored with MY
KEY
•
TP
MENU leads to the menu system. Up/
scrolls between
down with the buttons
menu options.
•
ENTER selects or activates/deactivates a
menu option.
•
EXIT leads back one step in the menu
structure. A long press on EXIT will exit
the menu system.
Random
Disc text
News
Radio text
PTY scan
AF
Regional
Surround
246
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Control panels, audio
Control panel with headphones
socket*
tracks or to search for radio stations automatically.
Limitations
10
The audio source (FM, AM, CD etc.) played
back in the speakers cannot be controlled
from the rear control panel.
G026982
RDS messages may not appear if the radio is
playing back in the headphones while another
audio source is playing back in the speakers.
Headphones with an impedance of 16 –
32 ohm and sensitivity of 102 dB or higher
are recommended for best sound reproduction.
Activate/deactivate
The control panel is activated with SEL when
the audio system is active. Deactivation is
automatic when the audio system is deactivated or with a long press on SEL.
Scroll/search forward and backward
Short presses on
/
are used to
scroll between CD tracks or preset radio stations. Long presses are used to fast-wind CD
* Option/accessory, for more information, see Introduction.
247
10 Infotainment system
Audio system functions
On/Off switch – Audio
Volume control
Turn the knob
clockwise or anticlockwise
to raise or lower the volume respectively. The
volume control is electronic and has no end
position. Volume can also be raised (+) or
lowered (–) using the steering wheel keypad.
10
Selecting the audio source
Press the AM/FM
button repeatedly to
toggle between FM1, FM2 and AM. The CD
activates the CD player/changer.
button
Press the POWER button
audio system on or off.
to switch the
If the audio system is active when the ignition
is switched off, it will reactivate automatically
when the car is restarted.
248
Turn SELECTOR
to toggle between the
external audio sources - AUX, USB* and BT*
and the internal audio sources CD and CD
changer*.
External audio sources
AUX
The AUX AUX input can be used for connecting an iPod® or an MP3 player.
* Option/accessory, for more information, see Introduction.
AUX input and audio switch for AUX/RSE*.
AUX input (3.5 mm)
Audio switch AUX/RSE*
If the car is equipped with RSE* then there is
a switch for audio from AUX and RSE. The
switch can be in two positions:
•
AUX - The audio from an external audio
source is played back through the audio
system.
•
RSE - The audio from the RSE is played
back through the audio system.
10 Infotainment system
Audio system functions
IMPORTANT
USB*
2. Connect your iPod®, MP3 player or USB
memory stick to the USB connection*,
see preceding illustration.
> The text Loading appears on the display when the system loads the file
structure on the storage media. This
takes a while.
The cover for the cup holders must be
open when the connector is in the AUX
input.
NOTE
The audio quality may be impaired if the
player is charged while the audio system is
in AUX mode. In which case, avoid charging the player.
Sometimes the external AUX audio source
can be heard at a different volume to the
internal audio sources. The audio quality may
be impaired if the audio volume from the
external audio source is too high or too low.
Prevent this by adjusting the input volume of
the external audio source:
1. Select AUX input volume in the menu
and press ENTER.
2. Control the volume with SELECTOR or
up/down with the buttons
. Finish with
ENTER.
NOTE
Does not work for the steering wheel keypad.
10
When the loading is finished the track information is shown on the display.
Now it is possible to fast-wind/change tracks
/
:
using the buttons
USB connection*.
If you choose to connect an iPod®, MP3
player or a USB memory stick to the USB
connection* then you can control the media
via the car's audio controls.
NOTE
Connect the media player/USB memory
stick to the cable and the port, put in the
parts, and close the glovebox.
1. Select USB using the SELECTOR button.
> Connect device appears on the display.
•
Short presses are used to scroll between
tracks.
•
Long presses are used to fast-wind
tracks.
The steering wheel keypad can also be used
for this purpose.
NOTE
The system supports the playback of
music files in the MP3, WMA and WAV file
formats. However, there are variants of
these file formats that are not supported
by the system. The system also supports
most iPod® models produced in 2005 or
later. iPod® Shuffle is not supported.
}}
* Option/accessory, for more information, see Introduction.
249
10 Infotainment system
Audio system functions
USB memory stick
10
To facilitate the use of a USB memory stick,
avoid storing any files other than music files
in the memory. It takes considerably longer
for the system to load storage media that
contains items other than compatible music
files.
NOTE
The system supports removable media
which is compatible with USB 2.0 and the
FAT32 file system, and can handle a maximum of 500 folders and 64 000 files. The
memory must have a capacity of at least
256 Mb.
via the steering wheel keypad*. In some
mobile phones it is also possible to change
tracks from the phone.
To be able to play back the audio a device
must first be paired and connected to the car.
For information about pairing and connection,
see page 275. BT must also be selected as
audio source, see page 248.
NOTE
The Bluetooth® mobile phone must support the Audio/Video Remote Control Profile (AVRCP) and Advanced Audio Distribution Profile (A2DP). The phone should use
AVRCP version 1.3, A2DP 1.2. Otherwise
some functions may not work.
iPod®
An iPod® is charged and supplied with power
by the USB connection via the player's connection cable. However, if the player's battery
is fully discharged then it must be charged
before being connected.
Streaming audio via Bluetooth®*
General
If the car is equipped with Bluetooth® handsfree* and a mobile phone is connected then
the audio system can wirelessly play back
streaming audio files from the mobile phone.
Navigation and control of the sound can be
carried out via the centre console buttons or
250
NOTE
Not all mobile phones available in the market are fully compatible with the
Bluetooth® function in the car's audio system. Volvo recommends that you contact
an authorised Volvo dealer or visit
www.volvocars.com for information on
compatible phones and external media
players.
Playback
Turn SELECTOR in order to select BT as
audio source.
* Option/accessory, for more information, see Introduction.
Now it is possible to fast-wind/change audio
/
:
file using the buttons
•
Short presses are used to scroll between
audio files.
•
Long presses are used to fast-wind audio
files.
The steering wheel keypad can also be used
for this purpose.
Optimum sound reproduction
The audio system is calibrated for optimum
sound reproduction by means of digital signal
processing.
This calibration takes into account loudspeakers, amplifiers, passenger compartment
acoustics, listener position etc. for each combination of car model and audio system.
There is a also a dynamic calibration that
takes into account the level set for the volume
control, radio reception and vehicle speed.
The controls that are explained in this
owner's manual, e.g. Bass, Treble and Equalizer, are only intended for the user to be able
to adapt the sound reproduction according to
personal taste.
10 Infotainment system
Audio system functions
Audio settings
1. Press the SOUND button
Surround*
NOTE
.
2. Press the SOUND button repeatedly until
you come to the function you wish to set.
Choose between BASS, TREBLE,
FADER, BALANCE, CENTRE* or
SURROUND*.
3. Use the SELECTOR knob
to adjust
the level. The display shows a scale from
min. to max. position. The middle indicates the normal position.
The level for the centre speaker can only
be set if Dolby Pro Logic II (DPL II) or
three channel stereo (3-CH) is selected in
the menu.
Surround settings govern the spatial perception of the sound. The settings, including activating and deactivating for each respective
audio source, are made separately.
Programme type
Display
shows
symbol in the display indicates that
The
Dolby Pro Logic II is active. There are three
different settings for surround sound:
Bass
BASS
Treble
TREBLE
Balance between the left
and right-hand speakers
BALANCE
Balance between the
front and rear speakers
FADER
Level for centre speaker
CENTRE*
Level for surround sound
SURROUND*
10
• Pro Logic II
• 3 channels
• Off (two channel stereo)
Activating/deactivating surround sound
1. Press MENU, scroll to AUDIO MODE
and press ENTER.
2. Select SURROUND and press ENTER.
3. Select Pro Logic II, 3 channels or Off
and press ENTER.
Dolby Surround Pro Logic II is a trademark of Dolby Laboratories Licensing
Corporation. Dolby Pro Logic II Surround
System is manufactured under license from
Dolby Laboratories Licensing Corporation.
}}
* Option/accessory, for more information, see Introduction.
251
10 Infotainment system
Audio system functions
Equalizer front1
10
This function is used to fine-tune the sound
from the front speakers.
1. Select AUDIO MODE in the menu and
press ENTER.
2. Select Equalizer front and press
ENTER.
3. Use the menu selection buttons or the
SELECTOR knob to set the level.
4. Press ENTER to select the next frequency. You can select five frequencies.
5. Press ENTER until you come to menu
mode to save any changes.
Equalizer rear1
This function is used to fine-tune the sound
from the rear speakers.
1. Select AUDIO MODE in the menu and
press ENTER.
2. Select Equalizer rear and press ENTER.
3. Use the menu selection buttons or the
SELECTOR knob to set the level.
4. Press ENTER to select the next frequency. You can select five frequencies.
1
252
Certain audio systems.
5. Press ENTER until you come to menu
mode to save any changes.
10 Infotainment system
Radio functions
Tuning
Manually seek known frequency
MY KEY
PHONE
LUM
VO E
LE CTOR
SE
SOUND
POWER
1
4
GHI
7
PQRS
AUTO
CLEAR
MENU
5
6
JK L
MNO
8
9
TUV WXYZ
0
3. Frequency can be adjusted with a short
or
press on one of the arrow keys,
.
SCAN
#
G027114
*
3
DEF
2. Release the button when the desired frequency shows in the display.
EXI T
ENTER
2
ABC
10
1. Select radio mode AM/FM1/FM2 using
the SELECTOR knob (3) or the AM/FM
button (1).
2. A short press on the
or
button is used to search for the next strong
station.
3. Press one of the buttons again to search
again.
G027119
AM FM
CD
AUTOSTORE – autostoring stations
1. Hold the
or
button
depressed. MAN is shown in the display.
The radio slowly scrolls in the desired
direction, increasing its tempo after a few
seconds.
Manual adjustment mode stays in effect
five seconds after the last press.
Storing stations
To store a selected station under one of the
station setting buttons 0 – 9 (2):
1. Set the desired station.
2. Press and hold the required station storage button. The sound mutes a few seconds. Channel stored is shown in the
display. The station is now stored.
You can store up to 10 stations each for AM,
FM1 and FM2, i.e. a total of 30 stations.
AUTO (1) seeks out the ten strongest radio
stations and stores them automatically in a
separate memory. The function is especially
useful in areas where the radio stations and
their frequencies are unfamiliar.
Start autostoring
1. Select wavelength using AM/FM.
2. Hold AUTO (1) depressed until
Autostoring appears on the display.
Once Autostoring disappears from the display, the stations are stored. The radio continues in Auto mode and AUTO appears on
the display. The automatically stored stations
can now be selected using the 0 - 9 buttons.
}}
253
10 Infotainment system
Radio functions
10
If there is no station with an adequately
strong signal then the display shows No
station found.
Cancelling automatic storage of
stations
–
Press EXIT.
3. Close using SCAN or EXIT.
Storing a station
A selected station can be stored as a preset
while SCAN is active.
–
Selecting an autostored preset
Allowing the radio to remain in Auto mode
provides access to the autostored presets.
SCAN is interrupted and the stored station
can be selected as a preset.
1. Briefly press AUTO (1). AUTO appears in
the display.
RDS functions1
2. Press one of the 0 - 9 buttons.
3. The radio remains in Auto mode until it is
exited by a brief press on AUTO (1), EXIT
or AM/FM.
Scanning
SCAN (2) automatically searches through a
wavelength for strong stations. When a station is found, it is played for approx. 8 seconds before scanning is resumed.
Activating/deactivating Scan
1. Select wavelength using AM/FM.
2. Press SCAN (2) to activate. SCAN
appears in the display.
1
254
Press one of the 0 - 9 buttons and hold it
depressed until the message Station
stored appears on the display.
The RDS functions available vary in the different markets.
RDS (Radio Data System) links FM transmitters into a network. An FM transmitter in such
a network sends information that gives an
RDS radio the following functions:
Volume control – NEWS/TP/ALARM
NOTE
If a CD for example is playing when the
radio receives a traffic bulletin, the CD
player is put in pause mode. The message
is played at the volume selected for that
type of message. Playback of the originally
selected audio source is then resumed at
the previous volume. If volume is adjusted
while the bulletin is played, the new volume is saved and used for the next bulletin.
News – NEWS
This function interrupts other sound sources,
e.g. CD, when a news broadcast starts.
•
Automatically switches to a stronger
transmitter if reception in the area is poor.
1. Select radio mode using the SELECTOR
knob or the AM/FM button.
•
Searches for programme form, such as
traffic information or news.
2. Select News in the menu and press
ENTER.
•
Receives text information on the current
radio programme.
3. News appears on the display.
NOTE
Some radio stations do not use RDS or
only a selected range of its functions.
4. Select News again and press ENTER to
deactivate the News function.
With this function, programmes from RDS
stations that are news-coded will interrupt
other audio sources using the volume setting
for this specific purpose. As soon as the
10 Infotainment system
Radio functions
Press the EXIT button. The TP function
remains active and the radio waits for the
next traffic bulletin.
news broadcast is finished, the audio system
returns to the previous audio source and
resumes the previous volume setting.
–
If you do not wish to listen to a news item in
progress:
TP Search
–
Press the EXIT button. The NEWS function remains active and the radio waits for
the next news programme.
Traffic information – TP
This function interrupts other audio sources in
order to broadcast traffic information from
RDS stations. The message is heard at the
volume set for this specific purpose. As soon
as the message ends, the radio returns to the
previous audio source and volume setting.
This function allows you to listen to traffic
information when travelling between different
countries and states in Europe without needing to select a station.
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select TP and press ENTER.
3. Select TP search and press ENTER.
To deactivate the function, select TP search
again and press ENTER.
1. Select TP in the menu and press ENTER.
Radio text
2. TP appears on the display.
Some RDS stations transmit information on
programme content, artists, etc. This information can be indicated with text in the display.
3. Select TP again and press ENTER to
deactivate the TP function.
TP is shown in the display when this function
is active. If the set station can send traffic
appears on the disinformation then
play. Traffic information will only interrupt the
sound source if
play.
is shown in the dis-
If you do not wish to listen to a traffic bulletin
in progress:
1. Press the MENU button.
2. Select Radio text in the menu and press
ENTER.
3. Select Radio text again and press
ENTER to deactivate.
message is broadcast. This function is used
to warn motorists of major accidents and catastrophes, such as a bridge collapse or an
accident at a nuclear plant.
10
Programme types – PTY
The PTY function can be used to select different programme types, such as pop or classical music. Use the PTY function to select
from among the different programme types
shown in the list below.
Display of programme type
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select PTY in the menu and press
ENTER.
3. Select Show PTY and press ENTER.
The PTY of the selected station is now shown
in the display.
NOTE
Not all radio stations have a PTY designation.
Alarm
Alarms are transmitted automatically and the
function cannot be deactivated. Alarm! is
shown in the radio display when an alarm
}}
255
10 Infotainment system
Radio functions
10
Programme types
Programme types
Current affairs
Pop music
Religion
Travel
Varied speech
Rock music
Country music
Social affairs
Documentary
Sport
Finance
Drama
Folk music
Phone in
Leisure & hobby
Education
Children's progs
Science
Oldies music
Weather & Metro
Information
Other music
Jazz music
Serious classic
Culture
Light classic
256
Searching for a specific programme
type
This function helps you find programmes with
a specific focus by searching the entire frequency band.
Easy listening
1. Select FM 1 or FM 2 and press the
MENU button.
National music
2. Select RADIO SETTINGS and press
ENTER.
3. Select PTY and press ENTER.
4. Select Select PTY and press ENTER.
5. Press ENTER for one or more of the listed programme types you select. The
PTY symbol in the display illuminates
when the first selection is made and the
radio continues in standby for PTY.
6. Once you have selected all desired types,
select EXIT/CLEAR to exit the PTY list.
7. Select PTY scan and press ENTER. If
the radio finds a station with the selected
programme type, it is played through the
speakers.
8. If the radio finds a station that is unsuitable, continue the search with the
/
buttons.
9. If no stations with the selected programme type are found, the radio
resumes its previous frequency. PTY then
remains in standby mode until the
selected programme type is broadcast, at
which time the radio automatically
switches to the station sending the
selected programme type.
In order to deactivate PTY standby, enter the
menu and select Clear all PTY. The symbol
PTY disappears from the display and the
radio resumes normal mode.
10 Infotainment system
Radio functions
Traffic information – TP STATION
News – NEWS STATION
Automatic frequency update – AF
Here, you set from which station traffic information is to be heeded.
Here, you set from which station news is to
be heeded.
must be shown in the disNote that
play for this to work.
Note that the set station in question must be
an RDS station for this to work.
Activating/deactivating TP STATION
Activating/deactivating NEWS STATION
The AF function selects one of the strongest
transmitters for a set station. The radio may
sometimes need to search through the entire
FM wavelength to find a strong transmitter. If
this occurs, the radio mutes and PI Seek
Press EXIT to cancel appears in the display.
Listen to the station from which traffic information is to be heeded.
Listen to the station from which news is to be
heeded.
1. Select RADIO SETTINGS in the menu
and press ENTER.
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select TP and press ENTER.
2. Select NEWS STATION and press
ENTER.
3. Select TP-STATION and press ENTER.
4. Select Set current to activate or RESET
to deactivate and press ENTER.
NOTE
Now only traffic information from the
stored station will by played.
3. Select TP-STATION and press ENTER.
4. Select Set current to activate or RESET
to deactivate and press ENTER.
NOTE
Now only news from the stored station will
by played.
10
Activating/deactivating AF
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select AF and press ENTER.
To reactivate AF, select AF and press
ENTER.
Regional radio programmes – REG
This function causes the radio to continue
with a regional transmitter even if its signal
strength is low.
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select Regional and press ENTER.
3. REG appears on the display.
4. To deactivate REG, select REG again
and press ENTER.
}}
257
10 Infotainment system
Radio functions
10
Enhanced Other Networks – EON
Resetting RDS functions
The EON function is especially useful in urban
areas with many regional radio stations. It
allows the distance between the car and the
radio station transmitter to determine when
programme functions should interrupt the
current audio source.
Resets all radio settings to the original factory
settings.
2. Select Reset all and press ENTER.
•
3. Press ENTER again to confirm.
Local – interrupts only if the radio station
transmitter is close.
• Distant2 – interrupts if the station trans-
mitter is far away, even if there is a lot of
static.
• Off – no interruption for programmes
from other transmitters.
Activating/deactivating EON
1. Select RADIO SETTINGS in the menu
and press ENTER.
2. Select EON and press ENTER.
3. Select Local, Distant or Off and press
ENTER.
2
258
Default/factory settings.
1. Select RADIO SETTINGS in the menu
and press ENTER.
10 Infotainment system
CD functions
Insert a CD (CD changer)
Audio files
–
Apart from normal music CDs, the CD player
supports MP3 and WMA format audio files.
Select an empty position with the number
buttons 1 - 6 or Up/Down on the navigation button.
An empty position is marked on the display.
The text Insert disc shows that a new disc
can be inserted. The CD changer can hold up
to six CDs.
–
Insert a CD into the CD changer slot (2).
G027116
CD eject
A CD will stay in the ejected position for
max. 12 seconds. Following which it is reinserted in the player and playback continues.
Start playback (CD player)
Single discs (CD player)
If a music CD is in the player when the audio
system is in CD mode then playback is
started automatically. Otherwise, load a disc
and change to CD mode using SELECTOR
(4) or CD(1).
All discs (CD changer)
Start playback (CD changer)
If a CD position with a music CD is already
selected when the audio system is activated
then playback starts automatically. Otherwise
change to CD changer mode using
SELECTOR (4) or CD (1) and select a disc
with the number buttons 1 - 6.
Eject individual discs by pressing the eject
button (3).
Eject all discs with a long press on the eject
button. The entire magazine is emptied disc
by disc. The message EJECT is shown in the
display.
This function can only be activated if the car
is stationary. Eject is interrupted if the car
begins to move.
Pause
If the volume is turned down completely, the
CD player is stopped. The player is restarted
when volume is increased.
10
NOTE
Certain types of copy-protected audio files
cannot be read by the player.
When a CD containing audio files is inserted
into the player the disc's directory structure is
read in. It may take a while before playback
starts due to the quality of the disc.
Navigation and playback
If a disc containing audio files is inside the CD
player then ENTER leads to the disc's directory structure. The directory structure is navigated in the same way as the audio system's
menu structure. Audio files have the symbol
and directories have the symbol
. Before playback starts
/
can be used to show the audio file's name if
the display is too narrow. Start playback of
the selected audio file with ENTER.
When the playback of a file is finished the
playback of the other files in the same directory continues. Directory change takes place
automatically when all files in the current
directory have been played back.
}}
259
10 Infotainment system
CD functions
10
Fast-wind/change CD tracks and audio
files
Short presses right/left on the
/
buttons are used to scroll between CD
tracks/audio files. Long presses are used to
fast-wind CD tracks/audio files. The steering
wheel keypad can also be used for this purpose.
Scan CD
This function plays the first ten seconds of
each CD track/audio file. Press SCAN to activate. Interrupt with EXIT or SCAN to continue
playback of the current CD track/audio file.
Scan only works on the selected disc. The
text SCAN is shown in the display when the
function is active.
NOTE
If disc text is activated then SCAN is not
shown in the display.
Random
This function plays the tracks in random
order. The random CD tracks/audio files can
be scrolled through in the normal way.
NOTE
It is only possible to scroll between random CD tracks on the current disc.
Activating/deactivating (CD player)
• RANDOM means that the tracks from
only one music CD are played.
• RANDOM ALL means that all tracks on
all music CDs in the CD changer are
played.
If a normal music CD is being played:
–
Select RANDOM in the menu and press
ENTER.
• RANDOM Folder means that the audio
files in a directory on the current CD are
played.
If a disc with audio files is being played:
–
Select Disc or Folder in the menu and
press ENTER.
NOTE
If disc text is activated then these messages are not displayed.
Activating/deactivating (CD changer)
If a normal music CD is being played:
1. Select Random in the menu and press
ENTER.
2. Scroll to Single disc or All discs and
press ENTER.
The option All discs only applies to the
music CDs in the changer.
If a CD with audio files is being played:
1. Select Single disc or Folder in the menu
and press ENTER.
2. Scroll to the required CD or folder and
press ENTER.
When you select another CD the function is
deactivated.
260
Different messages appear depending on
which random function is active:
Disc text
If title information is stored on a CD then it
can be shown in the display.
Activate/deactivate
Start CD playback.
–
Select Disc text in the menu and press
ENTER.
CDs
Using CD discs burned at home could result
in poor or non-existent sound.
10 Infotainment system
CD functions
WARNING
Only use standard discs (12 cm in diameter). Do not use CDs with adhesive disc
labels. The heat in the CD player may
cause the label to come off, damaging the
CD player.
10
261
10 Infotainment system
Menu structure – audio system
10
FM-MENU1
AM MENU
1. News
1. AUDIO SETTINGS*2
2. TP
3. Radio text
CD MENU
4. RADIO SETTINGS
1. Random
4.1. PTY
2. News
4.2. TP
3. TP
4.3. NEWS STATION
4. Disc text
4.4. AF
5. AUDIO SETTINGS*2
4.5. Regional
4.6. EON
4.7. Reset all
5. AUDIO SETTINGS*
5.1. Surround
5.2. Equalizer front
AUX MENU
1. AUX input volume
2. News
3. TP
4. AUDIO SETTINGS*2
5.3. Equalizer rear
5.4. Reset all
1
2
262
The RDS functions available vary in the different markets.
See FM MENU.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Phone functions*
10
Phone system components
}}
* Option/accessory, for more information, see Introduction.
263
10 Infotainment system
Phone functions*
10
Steering wheel keypad* - You can control the majority of phone functions using
the steering wheel keypad. When the
phone is active, the steering wheel keypad can only be used for phone functions. When in active mode, phone information is always shown in the control
panel display.
Microphone - The microphone for
handsfree is fitted in the roof by the sun
visor.
SIM card reader - The SIM card is
inserted into the front of the control
panel.
Centre console control panel - All
phone functions (except call volume) can
be regulated via the control panel.
Antenna - The antenna is mounted
against the windscreen, in front of the
rearview mirror.
General
•
•
•
•
Controls
Always put traffic safety first.
Switch off the phone system when refuelling the car.
Switch off the system near blasting work.
Volvo recommends that an authorised
Volvo workshop carries out phone system
servicing.
Emergency calls
Emergency calls to alarm centres can be
made without a SIM card as long as there is
coverage by a GSM operator.
G027117
Phone system components
1. Activate the phone.
2. Ring the emergency number that applies
to your region (within EU: 112).
3. Press ENTER in the control panel or in
the steering wheel keypad.
Display
ENTER – accept a call, make a menu
selection or activate the phone from
standby mode
On/Off/Standby
EXIT/CLEAR – terminate/refuse a call,
scroll back in the menu, cancel a selection or erase entered digits/characters
SIM card holder
Menu selection buttons
264
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Phone functions*
On/Off/Standby switch
Volume reduction during phone call
To activate the system:
If the phone rings when the radio is switched
on, the volume is lowered when the call is
answered. When the call is concluded, the
volume returns to the previously set level.
Radio volume can also be adjusted during a
phone call, whereby the newly selected level
will resume when the call is concluded. Audio
system volume can also be switched off completely during a phone call, see page 272.
–
Press the PHONE button (3) to activate
the phone system.
To switch off the system:
–
Hold the PHONE button depressed to
switch off the phone system
Continuing with system in standby mode:
Number/character buttons and menu
shortcuts
Seek – scroll forward or back when entering text and numbers
Increase/decrease call volume during
calls. The phone does not use the centre
speaker*
1. The phone will continue in standby mode
with a brief press of the PHONE button or
if you press EXIT/CLEAR.
This function only applies to the Volvo integrated phone system.
2. Reactivate the system with the PHONE
button.
Standby mode
When the phone is activated or in standby
mode, a handset is shown in the display.
If you switch off the car's ignition with the
phone system on, it will be on the next time
you switch on the ignition. No calls can be
received when the phone system is switched
off.
10
In standby mode, you can receive calls while
the audio system is active and information
from audio system sources is shown in the
display.
To use other functions of the phone system,
the phone must be in active mode.
}}
* Option/accessory, for more information, see Introduction.
265
10 Infotainment system
Phone functions*
Menu shortcuts
Contact your network operator if you experience difficulties with the SIM card.
Making and receiving calls
To call:
–
Traffic safety
To receive an incoming call:
–
The speed limiter can be disconnected using
menu function 5.6.
The phone can only be used with a valid SIM
card Subscriber Identity Module. Your network operator supplies this card.
Always insert the SIM card when you wish to
use the phone.
Press ENTER. You can also use Automatic Answer, see page 272.
The car's audio system can be muted automatically while a phone call is in progress,
see page 272.
Ending a call
–
Press EXIT/CLEAR on the steering wheel
keypad or control panel keypad.
1. Switch off the phone.
The audio system resumes its previous activity.
2. Open the SIM card holder with a short
press.
Refuse an incoming call by pressing EXIT/
CLEAR.
3. Insert the SIM card with the metallic surface down.
4. Make sure that the bevelled corner of the
SIM card matches the bevel of the holder.
5. Press in the holder.
266
Dial the number and press ENTER on the
steering wheel keypad or control panel
keypad.
For reasons of safety, parts of the phone
menu system cannot be accessed at speeds
in excess of 8 km/h. You may only complete
menu system activities that have already
been started.
G026980
10
SIM card
Once you have used the menu button to enter
the menu system, you can use numbers
instead of the arrows and the ENTER button
to select the right menu in the main menu
level. Each menu selection is numbered. The
numbers are shown in the display together
with the menu alternative.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
Phone functions*
Last dialled numbers
Using speed dial
Functions during a call
The phone automatically stores the last
phone numbers/names called.
1. To make a call, press and hold the
desired speed dial button for about two
seconds or press the button briefly and
then press ENTER.
The following functions are available during a
call (scroll with the arrows and press ENTER
to make a selection)
1. Press ENTER on the steering wheel or
control panel keypad.
2. Use the menu buttons to scroll forward or
back through the last numbers dialled.
They are shown in the display.
3. Press ENTER.
Speed dial
Storing speed dial numbers
A number stored in the phone book can be
linked to a speed dial button (1 – 9).
Proceed as follows:
1. Select Phone book in the menu and
press ENTER.
2. Scroll to Speed dial (see page 272) and
press ENTER.
3. Select which number is to be the speed
dial number. Press ENTER to confirm.
4. Search for the desired name or phone
number in the phone book. Press ENTER
to select.
2. Once you switch on the phone, wait a
moment before using speed dial.
NOTE
If you wish to use a speed dial number
then Menu 3.4 must be activated. See
Speed dial under Description of menu
options on page 271.
Call waiting
If you hear two beeps in your speaker during
a phone call, someone else is calling. This
function can be selected or deselected in the
menu.
When this occurs, you may accept or decline
the call. If you do not wish to take the call,
press EXIT/CLEAR or do nothing.
If you do wish to take the call, press ENTER.
Your current call will be put in "park mode". If
you press EXIT/CLEAR, both calls will be terminated.
Secret mode/
Secret mode off
Mute mode
Hold/Resume
Choose if the call is to
be parked or resumed
Phone book
Show phone book
10
The following functions are available when
you have a current call and a parked call
(scroll with the arrows and press ENTER to
make a selection)
Secret
mode/Secret
mode off
Mute mode
Phone book
Show phone book
Join
Speak with both parties
simultaneously (conference call)
Swap
Switch between the two
calls
}}
* Option/accessory, for more information, see Introduction.
267
10 Infotainment system
Phone functions*
10
Phone call volume
Storing phone numbers with names
Choose from the following alternatives:
Increase or decrease call volume during calls
by pressing the + or - buttons in the steering
wheel keypad.
1. Press the MENU button, select Phone
book and press ENTER.
1. Press ENTER and scroll with the arrows
until you find the desired name.
2. Scroll to New number and press
ENTER.
2. Press the key for the first letter of the
name (or enter the entire name) and press
ENTER.
When the phone is active, the steering wheel
keypad is locked to phone functions.
The phone must be in standby mode in order
to adjust the audio system with these buttons, see page 265.
Phone book
Phone numbers and names can be stored in
either the phone memory or the SIM card
memory.
3. Enter a name and press ENTER.
3. Press ENTER to call the selected number.
4. Enter a number and press ENTER.
5. Choose in which memory to save and
press ENTER.
Enter a name or message
Press the button with the desired character:
once for the first character, twice for the second, etc. Press 1 to enter a space.
Dialling from the memory
If the number of the person calling is found in
the phone book, his or her name is shown in
the display.
AM FM
CD
LE CTOR
SE
SOUND
EXI T
ENTER
The phone memory can store up to 255
names.
2
ABC
1
4
GHI
7
PQRS
AUTO
CLEAR
MENU
5
6
JK L
MNO
8
9
TUV WXYZ
0
SCAN
#
G027118
*
3
DEF
–
268
* Option/accessory, for more information, see Introduction.
1
space 1- ? ! , . : " ' ( )
2
abc2äåàæç
3
def3èé
4
ghi4ì
5
jkl5
6
mno6ñöòØ
7
pqrs7ß
8
tuv8üù
9
wxyz9
MY KEY
PHONE
LUM
VO E
POWER
Press the MENU button's down arrow (1)
or
in the steering wheel to search in
the phone book.
10 Infotainment system
Phone functions*
Double SIM cards
Specifications
*
Used if two characters are to be
ended with the same button.
Output
2W
0
[email protected]*#&$£/%
SIM card
small, 3 V
#
Switch between upper and lower
case.
Memory entries
255A
EXIT
Delete the last letter or number
entered. If you press for a long
time, the entire number and text is
deleted.
SMS
yes
Data/fax
no
Dualband
yes (900/1800)
1. Clear all entered characters with a long
press on the EXIT/CLEAR button.
2. Return to the menu with an additional
long press on the EXIT/CLEAR button.
G026980
A
Quitting text input:
10
The phone memory contains 255 positions. The number of
SIM card memory positions varies depending on your subscription.
IMEI number
Many network operators offer double SIM
cards - one for your car and one for another
phone. A double SIM card allows you to have
the same number for two different phones.
Ask your network operator about the options
available and the use of double SIM cards.
To block the phone, you must provide your
network operator with the phone's IMEI number. This is a 15 digit serial number that is
programmed into the phone. Dial *#06# to
show this number in the display. Write it
down and keep it in a safe place.
* Option/accessory, for more information, see Introduction.
269
10 Infotainment system
Menu structure – phone
Overview
10
2.4. Speed dial
1. Call register
1.1. Missed calls
2.4.2 Select numbers
4.6.4 Not reachable
2.5. Erase SIM
4.6.5 Fax calls
1.3. Dialled no.
2.6. Erase phone
4.6.6 Data calls
1.4. Erase list
2.7. Memory status
4.6.7 Cancel all
3. Messages
5. Change phone
1.4.2 Missed calls
3.1. Read
5.1. Car phone
1.4.3 Received calls
3.2. Write
5.2. Add phone
1.4.4 Dialled no.
3.3. Message settings
5.3. Added phones1
1.5. Call duration
3.3.1 SMSC number
1.5.1 Last call
3.3.2 Validity time
1.5.2 Call count
3.3.3 Message type
1.5.3 Total time
1.5.4 Reset timer
2. Phone book
4. Call options
4.1. Send my no.
4.2. Call waiting
2.1. Search
4.3. Automatic answer
2.2. New number
4.4. Automatic redial
2.3. Copy all
4.5. Voice mail number
2.3.1 SIM to phone
2.3.2 Phone to SIM
270
4.6.3 Not answered
1.2. Received calls
1.4.1 All calls
1
4.6.2 When engag.
2.4.1 Active
Max. 3 phones.
4.6. Diversions
4.6.1 All calls
NOTE
The menu above only applies to cars with
BluetoothTM handsfree.
6. Tel. settings
6.1. Network
6.1.1 Automatic
6.1.2 Manual select
6.2. SIM security
6.2.1 On
6.2.2 Off
10 Infotainment system
Menu structure – phone
1.4.2. Missed
2.4. Speed dial
6.3. Change PIN code
1.4.3. Received
6.4. Audio
1.4.4. Dialled
A number stored in the phone book can be
stored as a speed dial number.
6.2.3 Automatic
2.5. Erase SIM
6.4.1 Ring volume
1.5. Call duration
Erase the entire SIM card memory.
6.4.2 Ring signal
Duration of all calls or of the most recent call.
The phone code is required to reset the call
timer (see menu 5.4).
2.6. Erase phone
1.5.1. Last call
Shows how many positions are occupied in
the SIM card and phone memory. The table
shows how many of the total number of positions are occupied, e.g. 100 (250).
6.4.3 Mute radio
6.4.4 Msg. beep
6.5. Factory settings
Description of menu options
1. Call register
1.5.2. Call count
1.5.3. Total time
1.5.4. Reset timer
1.1. Missed calls
2. Phone book
List of missed calls. You can choose to call,
erase or store the number in the phone book.
Search for a name in the phone book.
2.1. Search
1.2. Received calls
2.2. New number
List of received calls. You can choose to call,
erase or store the number in the phone book.
Store names and phone numbers in the
phone book, see page 267.
1.3. Dialled no.
2.3. Copy all
List of dialled numbers. You can choose to
call, erase or store the number in the phone
book.
Copy phone numbers and names from the
SIM card to the phone memory.
1.4. Erase list
Erase the lists found in the menus 1.1, 1.2
and 1.3 as below.
2.3.1. From SIM to phone memory
2.3.2. From phone to SIM memory
10
Erase the entire phone memory.
2.7. Memory status
3. Messages
3.1. Read
Received text messages. Select whether to
erase, forward, change or save the entire
message or parts of it.
3.2. Write
Write a message using the keypad. Choose
whether to save or send it.
3.3. Message sett
Enter the number (SMSC number) of the message centre to which messages are to be
transferred as well as how long they are to be
saved at the message centre. Contact your
network operator for information on message
1.4.1. All
}}
271
10 Infotainment system
Menu structure – phone
10
settings. Normally, these settings should not
be altered.
This setting only applies during the call in
progress.
6. Phone settings
3.3.1. SMSC number
4.6.2. When engag.
3.3.2. Validity time
4.6.3. Not answered
3.3.3. Message type
4.6.4. Not reachable
Choose a network automatically or manually.
The selected network is shown in the display
in the phone's basic mode.
4. Call options
4.1. Send my no.
4.6.5. Fax calls
4.6.6. Data calls
4.6.7. Cancel all
Displays or hides your phone number to/from
the person you call. Contact your network
operator regarding ex-directory numbers.
5. Change phone
4.2. Call waiting
5.1. Car phone
Be alerted during a phone call that there is
another incoming call.
5.2. Add phone
4.3. Auto answer
Automatically answers incoming calls.
4.4. Call back
Calls a previously engaged number.
4.5. Voice mail number
Stores voice mail number.
4.6. Diversion
Choose when and what type of calls are to be
diverted to a specified phone number.
4.6.1. All calls
Select the built-in phone.
6.1. Network
6.1.1. Auto
6.1.2. Manual select
6.2. SIM security
Select if the PIN code should be on, off or if
the phone should automatically give the PIN
code.
6.2.1. On
6.2.2. Off
Add mobile phones to the list Added phones.
6.2.3. Automatic
5.3. Added phones
6.3. Change PIN code
Select to connect to one of the added phones
(up to 3 phones).
NOTE
The menu above only applies to cars with
BluetoothTM handsfree.
Change PIN code. Write down and save the
code in a safe place.
6.4. Sounds
6.4.1. Volume
Adjust the ring tone volume.
6.4.2. Ring signal
There are five different ring signals.
6.4.3. On/off
272
10 Infotainment system
Menu structure – phone
Mute radio.
6.4.4. Msg. beep
10
6.5. Factory default
Reset the system's factory settings.
273
10 Infotainment system
Bluetooth handsfree*
General
10
sun visor (2). The mobile phone can be operated by its own keys irrespective of whether
or not it is connected.
Phone functions, controls overview
NOTE
Only a selection of mobile phones are fully
compatible with the handsfree function.
Volvo recommends that you seek assistance from an authorised Volvo dealer or
visit www.volvocars.com for information
on compatible phones.
System overview.
Mobile phone
Microphone
Steering wheel keypad*
Centre console control panel
BluetoothTM
A mobile phone equipped with BluetoothTM
can be connected wirelessly to the audio system. The audio system then works handsfree,
with the option to control a range of the
mobile phone's functions remotely. The
microphone is fitted in the headlining by the
274
* Option/accessory, for more information, see Introduction.
Centre console control panel.
VOLUME - volume, same functionality
available in steering wheel keypad*.
Display
ENTER – accept a call, make a menu
selection or activate the phone from
standby mode.
PHONE – on/off/standby.
EXIT – terminate/refuse a call, scroll back
in the menu, cancel a selection or erase
entered digits/characters.
10 Infotainment system
Bluetooth handsfree*
MENU - leads to the menu system. Up/
down with the buttons scrolls between
menu options.
Seek – scroll forward or back when entering text and numbers.
Number/character buttons and menu
shortcuts.
Remember
The menus are controlled from the centre
console and the steering wheel keypad. For
general information on menus, see page 246.
NOTE
If the car is equipped with both
BluetoothTM handsfree and built-in phone
then there is an additional menu in the
phone menu, see page 278.
Activate/deactivate
A short press on PHONE activates the
handsfree function. The text PHONE at the
top of the display shows that it is in phone
shows that the
mode. The symbol
handsfree function is active.
One long press on PHONE deactivates the
handsfree function and disconnects a connected phone.
Connect mobile phone
5. Enter the number series shown in the
audio system display via the mobile
phone keypad.
A mobile phone is connected in different
ways depending on whether or not it has
been connected previously. To connect a
mobile phone for the first time, follow the
instructions below:
10
Alternative 2 - via the phone's menu system
Alternative 1 - via the car's menu system
1. Make the mobile phone detectable/visible
via BluetoothTM, see the mobile phone's
manual or www.volvocars.com.
2. Activate the handsfree function with
PHONE.
> Menu option Add phone appears on
the display. If one or more mobile
phones have already been registered
then these are also shown.
3. Select Add phone.
> The audio system searches for mobile
phones in the vicinity. The search
takes approximately 30 seconds. The
mobile phones detected are specified
with their respective BluetoothTM name
in the display. The handsfree function's
BluetoothTM name is shown in the
mobile phone as My Volvo Car.
4. Choose one of the mobile phones in the
audio system display.
1. Activate the handsfree function with
PHONE. If there is a phone connected,
disconnect the connected phone.
2. Search with the phone's BluetoothTM, see
the mobile phone's manual.
3. Select My Volvo Car in the list of units
detected in your mobile phone.
4. Enter the PIN code '1234' into the mobile
phone when prompted for the PIN code.
5. Select to connect to My Volvo Car from
the mobile phone.
The mobile phone is registered (paired) and
connected automatically to the audio system
while the text Synchronising is shown in the
display. For more information on how mobile
phones are registered, see page 277.
When the connection is established the symis shown and the mobile phone's
bol
BluetoothTM name is shown in the display.
Now the mobile phone can be controlled from
the audio system.
}}
* Option/accessory, for more information, see Introduction.
275
10 Infotainment system
Bluetooth handsfree*
To call
10
1. Make sure that the text PHONE is shown
at the top of the display and that the
symbol is visible.
2. Dial the number or use the phone book,
see page 277.
3. Press ENTER.
The call is interrupted with EXIT.
Disconnecting the mobile phone
Automatic disconnection takes place if the
mobile phone moves out of the audio system's range. For more information on connection, see page 277.
Manual disconnection takes place by deactivating the handsfree function with one long
press on PHONE. The handsfree function is
also deactivated when the engine is switched
off.
When the mobile phone has been disconnected an ongoing call can continue with the
mobile phone's built-in microphone and
speaker.
NOTE
Some mobile phones require that the
transfer from handsfree is confirmed from
the mobile phone's keypad.
276
Making and receiving calls
Incoming call
Calls are accepted with ENTER even if the
audio system is in CD or FM mode for example. Refuse or end with EXIT.
Automatic answer
The automatic answer function means that
calls are accepted automatically. Activate/
deactivate under PHONE MENU CALL
OPTIONS Automatic answer.
In call menu
Press MENU or ENTER during an ongoing
call to access the following functions:
• Mute microphone - audio system microphone is muted.
• Move call to mobile - the call is transferred to the mobile phone.
NOTE
With certain mobile phones the connection
is terminated when the privacy function is
used. This is normal. The handsfree function asks if you want to reconnect.
• Phone book – searching in the phone
* Option/accessory, for more information, see Introduction.
book.
NOTE
A new call cannot be started during an
ongoing call.
Audio settings
Phone call volume
Call volume can be adjusted during calls. Use
the steering wheel keypad*.
Audio system volume
In phone mode (PHONE) the audio system
volume can be adjusted as usual with
VOLUME.
The audio source can be automatically muted
for incoming calls under PHONE MENU
PHONE SETTINGS SOUNDS AND
VOLUME Mute radio.
Ring volume
Go to PHONE MENU PHONE SETTINGS
SOUNDS AND VOLUME Ring signal
/
on the convolume and adjust with
trol panel in the centre console.
Ring signals
The handsfree function has integrated ring
signals that can be selected under PHONE
MENU PHONE SETTINGS SOUNDS
10 Infotainment system
Bluetooth handsfree*
AND VOLUME
signal 1 etc.
Ring signals
Ring
NOTE
The connected mobile phone's ring signal
is not deactivated when one of the handsfree system's integrated signals is used.
system searches for the last phone connected its name is shown in the display. To
change over to manual connection of another
phone, press EXIT.
Manual connection
If you want to connect a mobile phone other
than the last connected or change the connected mobile phone, proceed as follows:
In order to select the connected phone's ring
signal1, go to PHONE MENU PHONE
SETTINGS SOUNDS AND VOLUME
RING SIGNALS Use mobile phone
signal.
Set the audio system in phone mode
(PHONE) and follow the instructions on the
display or change the connected mobile
phone by using the menu system as described below.
More on registering and connecting
The menu structure is available in two variants depending on whether the car only has
BluetoothTM or if the car also has a built-in
phone.
A maximum of 3 mobile phones can be registered. Registration is performed once per
phone. After registration the mobile phone is
in the list of added phones. Not more than
one mobile phone can be connected at a
time. Phones can be deregistered under
PHONE MENU BLUETOOTH Remove
phone.
Automatic connection
When the handsfree function is active and the
last mobile phone connected is in range it is
connected automatically. When the audio
1
•
For cars with only BluetoothTM the connection is made under PHONE MENU
BLUETOOTH Change phone Add
phone or select one of the previously
connected phones.
•
For cars with built-in phone and
BluetoothTM the connection is made
under PHONE MENU Change phone
Add phone or select one of the previously connected phones.
Phone book
All use of the phone book presupposes that
the text PHONE is shown at the top of the
display and that the
symbol is visible.
10
The audio system stores a copy of the phone
book from each registered mobile phone. The
phone book is copied automatically to the
audio system during each connection. Deactivate the function under PHONE SETTINGS
Synch. phone book. Searching for contacts is only performed in the connected
mobile phone's phone book.
NOTE
If the mobile phone does not support
copying of the phone book then The list is
empty is shown when copying is finished.
If the phone book contains a ringing caller's
contact information then this is shown in the
display.
Searching for contacts
The easiest way to search in the phone book
is with long presses on the keys 2–9. This
starts a search in the phone book based on
the key's first letter.
Not supported by all mobile phones.
}}
* Option/accessory, for more information, see Introduction.
277
10 Infotainment system
Bluetooth handsfree*
10
The phone book can also be reached with the
button on the control panel in the centre
on the steering wheel
console or with
keypad. Scroll between contacts with the
/
buttons or with
/
. The
search can also be carried out from the
phone book's Search menu under
PHONEBOOK Search:
1. Enter the first few letters of the contact
and press ENTER. Or simply press
ENTER.
2. Scroll to a contact and press ENTER to
call.
Voice recognition
The mobile phone's voice recognition function for dialling can be used by holding in
ENTER.
NOTE
Only a selection of mobile phones are fully
compatible with the voice recognition
function. Volvo recommends that you contact an authorised Volvo dealer or visit
www.volvocars.com for information on
compatible phones.
2
278
Voice mail number
Voice mail number can be changed under
CALL OPTIONS Voice mail no.:. If there is
no number stored then this menu can be
reached with one long press on 1. Press 1 for
a long time to use the stored number.
Call lists
The call lists are copied to the handsfree
function at each new connection and are then
updated during the connection. Press ENTER
to show the last dialled. Other call lists are
available under CALL REGISTER.
NOTE
Certain mobile phones show a list of the
last dialled numbers in reverse order.
Inputting text
Input text using the keypad in the centre console. Press once for the key's first character,
twice for the second etc. Continue pressing
for more characters, see the table on page
268.
A short press on EXIT deletes an input character. One long press on EXIT clears all input
characters.
/
on the control panel in
the centre console scrolls between the characters.
A maximum of 3 phones.
* Option/accessory, for more information, see Introduction.
Menu structure BluetoothTMhandsfree
NOTE
The menu for BluetoothTM handsfree is
available in two variants. For cars with only
BluetoothTM handsfree and for cars with
built-in phone and BluetoothTM handsfree.
1. CALL REGISTER
1.1. Last 10 missed
1.2. Last 10 received
1.3. Last 10 dialled
2. PHONEBOOK
2.1. Search
2.2. Copy to phone
3. BLUETOOTH
3.1. Change phone
3.1.1. Add phone
3.1.2. Added phones2
3.2. Remove phone
3.3. Connect fr. mobile phone
3.4. Bluetooth info. for the car
10 Infotainment system
Bluetooth handsfree*
4. CALL OPTIONS
3.2. Connect fr. mobile phone
4.1. Automatic answer
4.2. Voice mail no.:
5. PHONE SETTINGS
5.1. SOUNDS AND VOLUME
5.1.1. Ring signal volume
3.3. Bluetooth info. for the car
4.1. Automatic answer
4.2. Voice mail no.:
5. Change phone
5.1.2. Ring signals
5.1. Car phone
5.1.3. Mute radio
5.2. Add phone
5.2. Synch. phone book
10
4. CALL OPTIONS
5.3. Added phones2
6. PHONE SETTINGS
BluetoothTM
Menu structure handsfree with built-in phone
1. CALL REGISTER
1.1. Last 10 missed
1.2. Last 10 received
1.3. Last 10 dialled
6.1. SOUNDS AND VOLUME
6.1.1. Ring signal volume
6.1.2. Ring signals
6.1.3. Mute radio
6.2. Synch. phone book
2. PHONEBOOK
2.1. Search
2.2. Copy to phone
3. BLUETOOTH
3.1. Remove phone
2
A maximum of 3 phones.
* Option/accessory, for more information, see Introduction.
279
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
10
General
Music
Different playback options
The RSE system can be used at the same
time as the car's infotainment system.
Playing back a CD disc
The disc can be played back in different
ways, scroll with the navigation buttons to
select playback option.
When the rear seat passengers are using
DVD or RSE-AUX while listening with headphones, the driver and front seat passenger
can still use the car's radio or CD player.
Power consumption, ignition positions
The system can be activated in ignition position I or II and while the engine is running.
When the car is being started the film stops
temporarily and continues when the engine
has started.
When the system has been used once without the ignition in position I it is blocked. To
restart, ignition position I must be activated.
1. Insert the CD with the label side turned
from the buttons.
> The disc starts to play back automatically.
2. Switch on the wireless headphones,
select CH A for left-hand screen or CH B
for right-hand screen.
> The sound is directed to the headphones.
3. Adjust the audio volume in the headphones using the volume control/wheel
on the headphones.
In which case a message will appear on
the screen.
A B
system in MODE-AUX and press
on the remote control to listen via the
speakers.
Selecting within a disc directory
1. Load the disc.
2.
Press
.
3. Scroll using the navigation buttons to
select a file.
4.
280
1. Press the right-hand navigation button to
move over in the right-hand menu.
2. Scroll using the navigation buttons to
select playback options.
3.
* Option/accessory, for more information, see Introduction.
Press
to select the subdirectory.
.
Confirm with
Change CD track
–
Alternatively - activate the car's audio
NOTE
In the event of extended use (more than 10
minutes) with the engine switched off - the
capacity of the car's battery may decrease
to such a low level that the engine cannot
be started.
When the dialogue box appears:
Change CD track with
or
fast-wind by holding the buttons
depressed.
Pause
1.
2.
3.
Pause and restart the disc with
Stop the disc with
Press
.
.
again to eject the disc.
Discs copied privately can be used.
However, playback and quality depend on the
quality of the source file, format and disc
quality.
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
AUX input, Electrical socket 12 V
System
Connecting the RSE AUX input
The input allows you to connect other equipment. Always follow the instructions included
with the external equipment, or from the manufacturer or reseller, when connecting. Equipment connected via the RSE AUX input can
use the screens, wireless headphones, headphones sockets and the car's speakers.
Formats supported by the system.
NOTE
To be able to play back the audio from the
RSE in the car's audio system the audio
switch AUX/RSE must be in position RSE,
see page 248.
G015700
Audio format
CD-DA, DVD Audio Playback,
MP3, WMA
Video format
DVD video, VCD, SVCD, DivX/
MPEG-4, WMA video, Photo
CD Kodak, Photo CD JPG
Disc format
DVD-RAM, DVD-ROM, DVDRW, DVD+RW, DVD-R, DVD
+R, CD-R, CD-ROM, CD-RW,
CD-3, HDCD
10
Advanced system settings
The RSE-AUX input is located in the centre console under the DVD player.
These settings can only be accessed when
the DVD player is empty.
1. Connect the video cable to the yellow
socket.
–
Press MEDIA MENU.
2. Connect the left-hand audio cable to the
white socket and the right-hand one to
the red socket.
GENERAL SETUP
3. Connect the power cable to the power
socket if your equipment is designed for
12 V.
AUDIO SETUP
ANGLE MARK
CAPTION
COMPRESSION
}}
* Option/accessory, for more information, see Introduction.
281
10 Infotainment system
RSE - Rear Seat Entertainment system - Dual Screen*
10
1. Unscrew the screw and detach the battery cover.
DVX(R)
REGISTRATION
PREFERENCES
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and insert
them.
TV TYPE
AUDIO
SUBTITLE
3. Fit the cover and screw in the screw.
DEFAULTS
NOTE
If the system is too hot to be used or if
battery voltage is too low then an information message appears on the screen.
Environmental care
Be sure to dispose of the exhausted batteries
in an environmentally safe manner.
Changing the battery in the remote
control and wireless headphones
The remote control and headphones are powered by 2 AAA batteries.
G030395
Take along extra batteries for a long journey.
Wireless headphones
G031359
1. Unscrew the screw and detach the battery cover.
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and insert
them.
Remote control
282
3. Fit the cover and screw in the screw.
* Option/accessory, for more information, see Introduction.
10 Infotainment system
10
283
Type designation...................................................................................
Dimensions and weights.......................................................................
Engine specifications............................................................................
Engine oil...............................................................................................
Fluids and lubricants.............................................................................
Fuel.......................................................................................................
Wheel and tyres, dimensions and pressure .........................................
Catalytic converter................................................................................
Electrical system...................................................................................
Type approval.......................................................................................
Symbols in the display..........................................................................
284
286
288
291
292
294
296
297
298
299
301
302
SPECIFICATIONS
11 Specifications
Type designation
Label location
11
286
11 Specifications
Type designation
Knowing the car's type designation, vehicle
identification and engine numbers can facilitate all contact with an authorised Volvo
dealer regarding the car and when ordering
spare parts and accessories.
Type designation, vehicle identification
number, maximum permissible weights,
codes for colour and upholstery and type
approval number. The label is visible
when the right rear door is opened.
NOTE
It is not intended that the decals illustrated
in the owner's manual should be exact
replicas of those in the car. They are
included to show their approximate
appearance and location in the car. The
information that applies to your particular
car is available on the respective decals
for your car.
11
Engine code and engine serial number.
Label for engine oil.
Gearbox type designation and serial number:
automatic gearbox AW
manual gearbox
automatic gearbox
Label for parking heater.
The car's identification number (VIN –
Vehicle Identification Number).
Further information on the car is presented in
the registration document.
287
11 Specifications
Dimensions and weights
Dimensions
11
288
Dimensions
mm
Dimensions
mm
A
Wheelbase
2857
H
Rear track
1624
B
Length
4807
I
Load width, floor
1064
C
Load length, floor, folded seat
2018
J
Width
1936
D
Load length, floor
1118
K
Width including door mirrors
2112
E
Height
1784
L
1936
F
Load height, floor
Width including folded-in door
mirrors
G
Front track
872
1634
Weights
Kerb weight includes the driver, the fuel tank
90% full and all fluids.
The weight of passengers and accessories,
and towball load (when a trailer is hitched,
see table) influences the payload and is not
included in the kerb weight.
Permitted maximum load = Gross vehicle
weight - Kerb weight.
11 Specifications
Dimensions and weights
NOTE
WARNING
The documented kerb weight applies to
cars in the standard version - i.e. a car
without extra equipment or accessories.
This means that for every accessory added
the loading capacity of the car is reduced
correspondingly by the weight of the
accessory.
The car's driving characteristics change
depending on how heavily it is loaded and
how the load is distributed.
Max. train weight (car+trailer)
Max. front axle load
Max. rear axle load
Equipment level
Examples of accessories that reduce loading capacity are the Kinetic/Momentum/
Summum equipment levels, as well as
other accessories such as Towbar, Load
carriers, Space box, Audio system, Auxiliary lamps, GPS, Fuel-driven heater, Safety
grille, Carpets, Cargo cover, Power seats,
etc.
Weighing the car is a certain way of ascertaining the kerb weight of your own particular car.
Gross vehicle weight
11
Max. load: See registration document.
Maximum roof load: 100 kg
For decal location, see page 286.
Towing capacities and towball load
Engine
Max. weight braked trailer, kg
Max. towball load, kg
D4 FWD
1800
90
other
2250
90
}}
289
11 Specifications
Dimensions and weights
11
290
Max. weight unbraked trailer, kg
Max. towball load, kg
750
50
11 Specifications
Engine specifications
NOTE
Not all engines are available in all markets.
Engine
A
B
Engine
codeA
Output
(kW/rpm)
Output
(hp/rpm)
Torque (Nm/
rpm)
No. of
cylinders
Bore
(mm)
Stroke
(mm)
Swept
volume
(litres)
Compression
ratio
T5
B5254T9
154/5000
210/5000
320/1500-4500
5
83
92,3
2,497
9.0:1
3.2
B6324S5
179/6400
243/6400
320/3200
6
84
96
3.192
10.8:1
D5
D5244T18
147/3900
200/3900
420/1900-2800
5
81.0
93.15
2.400
17.3:1
D4B
D5244T5
120/4000
163/4000
340/1750-3000
5
81.0
93.15
2.400
17.3:1
11
Engine code, component and serial number can be read on the engine, see page 286.
Certain markets
291
11 Specifications
Engine oil
Adverse driving conditions
Check the oil level more frequently for long
journeys:
11
•
•
•
•
towing a caravan or trailer
in mountainous regions
at high speeds
in temperatures colder than -30 °C or
hotter than +40 °C.
This can produce abnormally high oil temperature or oil consumption.
Also check the oil level more often if the car is
often driven short distances (less than 10 km)
when temperatures are low (below +5 °C).
Choose a fully synthetic engine oil for adverse
driving conditions. It provides extra protection
for the engine.
Volvo recommends:
292
IMPORTANT
In order to fulfil the requirements for the
engine's service intervals all engines are
filled with a specially adapted synthetic
engine oil at the factory.The choice of oil
has been made very carefully with regard
to service life, starting characteristics, fuel
consumption and environmental impact.
An approved engine oil must be used in
order that the recommended service intervals can be applied. Only use a prescribed
grade of oil for both filling and oil change,
otherwise you will risk affecting service life,
starting characteristics, fuel consumption
and environmental impact.
Volvo Car Corporation disclaims all warranty liability if engine oil of the prescribed
grade and viscosity is not used.
Volvo recommends that oil changes are
carried out at an authorised Volvo workshop.
11 Specifications
Engine oil
Engine oil grade
Engine
Engine code
Recommended oil grade
Volume, incl. oil filter
(litres)
A
T5
B5254T9
Oil grade: ACEA A5/B5
approx 5.5
3.2
B6324S5
Viscosity: SAE 0W–30.
approx 6.8
D5
D5244T18
approx. 5.7
D4A
D5244T5
approx. 5.7
11
Certain markets
For filling engine oil, see page 213.
293
11 Specifications
Fluids and lubricants
Automatic gearbox
11
Volume (litres)
Prescribed transmission fluid
TF-80SC
7.0
AW1
AW55-51
7.7
JWS 3309
Fluids
Fluid
System
Coolant
T5
8.7
3.2
9.7
D4 and D5
8.7
Refrigerant
Air conditioning
Volume
(litres)
B
Recommended oil grade
Coolant recommended by Volvo mixed with 50% waterA, see the packaging. The thermostat starts opening at:
90 °C in petrol engines and at 82 °C in diesel engines
R134a (HFC134a)
Oil: PAG
Brake fluid
Brake system
0.6
DOT 4
Power steering
fluid
Power steering
1.0
WSS M2C204-A or equivalent product with same specifications.
of which reservoir
0.2
Washer fluid
Fuel
A
B
294
6.5
Washer fluid recommended by Volvo - with frost protection during cold weather and
below freezing point.
Petrol engine
approx. 80
Petrol: see page 139
Diesel engine
approx. 68
Diesel: see page 139
Water quality must fulfil the standard STD 1285.1.
Refrigerant quantity varies depending on engine variant. Volvo recommends that you contact an authorised Volvo workshop for the correct information.
11 Specifications
Fluids and lubricants
IMPORTANT
The recommended transmission fluid must
be used to prevent damage to the gearbox. Do not mix with any other transmission fluid. If the transmission is topped up
with a different fluid, contact a workshop
nearby for servicing. Volvo recommends
that you contact the nearest authorised
Volvo workshop.
11
NOTE
Under normal driving conditions the gearbox oil does not need changing during its
service life. However, it may be necessary
under adverse driving conditions, see
page 292.
295
11 Specifications
Fuel
Fuel consumption
There are several causes that can affect fuel
consumption negatively. Examples of this are:
11
•
•
The driver's driving style.
•
High speed results in increased wind
resistance.
•
Fuel quality, road and traffic conditions,
weather and the condition of the car.
If the customer has specified wheels
larger than those fitted as standard on the
model's basic version, then resistance
increases.
Even a combination of the above-mentioned
examples can result in significantly improved
consumption.
To bear in mind
Tips that the driver can use in order to reduce
consumption:
296
•
Drive gently and avoid unnecessary
acceleration as well as braking too hard.
•
Drive with the correct air pressure in the
tyres and check this regularly - select
ECO tyre pressure for best results, see
the tyre pressure table on page 297.
•
Choice of tyres can affect fuel consumption - seek advice on suitable tyres from a
dealer.
See further information and more advice on
pages 13 and 136.
See page 141 for general information on fuel.
11 Specifications
Wheel and tyres, dimensions and pressure
Approved tyre pressures
Engine
All
Tyre size
Load, 1-3 persons
Max. load
ECO pressureA
Front (kPa)B
Rear (kPa)
Front (kPa)
Rear (kPa)
235/65R17
0-160
220
220
270
270
270
235/60R18
160+
220
220
270
270
-
255/50R19
0-160
240
240
270
270
270
255/45R20
160 +
240
240
270
270
-
0–80
420
420
420
420
-
Temporary Spare Tyre
A
B
Speed (km/h)
11
Economical driving, see page 183.
In certain countries there is the "bar" unit beside the SI unit "Pascal": 1 bar = 100 kPa (270 kPa = 2.70 bar).
NOTE
All engines, tyres or combinations of these
are not always available in all markets.
297
11 Specifications
Catalytic converter
General
11
The purpose of the catalytic converter is to
purify exhaust gases. It is located in the flow
of exhaust gases close to the engine so that it
quickly reaches operating temperature. The
catalytic converter consists of a monolith
(ceramic or metal) with channels. The channel
walls are lined with a thin layer of platinum,
rhodium and palladium. These metals act as
catalysts, i.e. they participate in and accelerate a chemical reaction without being used
up themselves.
Lambda-sondTM oxygen sensor
The Lambda-sond is part of a control system
intended to reduce emissions and improve
fuel economy.
An oxygen sensor monitors the oxygen content of the exhaust gases leaving the engine.
This value is fed into an electronic system
that continuously controls the injectors. The
ratio of fuel to air directed to the engine is
continuously adjusted. Together with the
three-way catalytic converter, these adjustments create optimal conditions for efficient
combustion of the harmful emissions (hydrocarbons, carbon monoxide and nitrous
oxides).
298
11 Specifications
Electrical system
General
The car has a voltage-regulated AC alternator. The electrical system is single-pole and
uses the chassis and engine casing as a conductor.
The battery capacity is dependent upon the
equipment level in the vehicle.
IMPORTANT
If the battery is replaced, take care to
replace it with a battery with the same cold
starting capacity and reserve capacity as
the original battery (see the label on the
battery).
11
Battery
Voltage, V
A
Cold start capacity,
Reserve capacity,
Capacity, Ah
CCA (Cold Cranking Amperes), A
minutes
12
600
120
70
12
800A
150
90
Cars equipped with diesel engine or parking heater
Bulbs
Lighting
Output (W)
Type
Dipped beam, halogen
55
H7 LL
Main beam, halogen
55
H7 LL
Extra main beam, ABL
65
H9
Front direction indicators
21
HY21W
}}
299
11 Specifications
Electrical system
Lighting
11
300
Output (W)
Type
Position/Parking lamps, front; Side marker lamps, front; Courtesy lighting, rear
5
W5W LL
Side direction indicators, door mirrors
5
WY5W LL
Front courtesy lighting
5
Socket SV8.5 Length 38 mm
Glovebox lighting
5
Socket SV8.5 Length 43 mm
Vanity mirror lighting
2
T5 Socket W2x4.6d
Cargo area lighting
10
Socket SV8.5 Length 43 mm
Number plate lighting
5
C5W LL
Rear direction indicators
21
PY21WSV
Reversing lamp
21
P21W LL
Rear fog lamp
21
H21W LL
11 Specifications
Type approval
Remote control key system
Country/Area
EUROPE
11
301
11 Specifications
Symbols in the display
General
11
There are a variety of different symbols in the
display in the car. The symbols are divided
into warning, indicator and information symbols. Shown below are the most common
symbols with their meanings and a reference
to where in the manual further information
can be found. For more information on symbols and text messages, see pages 57 and
60.
symbol illuminates with a red or
The
amber glow depending on the severity of the
fault. An explanatory text is shown on the
information display at the same time.
Symbols in the display
Indicator and warning symbols in the
combined instrument panel
Symbol
Meaning
Page
Warning
21, 57,
59, 154,
155
Emissions system
302
57, 59
Symbol
Meaning
Page
Fault in the ABS
system
Symbol
Meaning
Page
58, 152
Airbags - SRS
21, 59
Rear fog lamp
59
Low oil pressure
57, 58
Stability system
DSTC
59, 154
Seatbelt reminder
18, 58
Engine preheater
(diesel)
59
Alternator not
charging
59
Indicator symbol
for trailer
59
Fault in brake
system
58, 151
Parking brake
applied
59
11 Specifications
Symbols in the display
Other information symbols in the
combined instrument panel
Symbol
Meaning
Page
Cruise control*
73
11
Information symbols in the centre
console display
Meaning
Page
Audio files
259
Directory in CD disc
259
Traffic information
255, 257
G021220
Symbol
Information symbol in rearview mirror
Symbol
Meaning
Page
Airbag, passenger
seat, deactivated
25
* Option/accessory, for more information, see Introduction.
303
12 Alphabetical Index
A
Air vents
instrument panel................................... 89
ABS fault.................................................... 58
Alarm
alarm indicator....................................
alarm signals.......................................
arming.................................................
automatic alarm activation.................
deactivating a triggered alarm............
disarming............................................
general................................................
reduced alarm level............................
Active Xenon headlamps..................... 62, 65
Active Yaw Control.................................. 153
Adaptive system...................................... 148
Additional heater........................................ 96
Adjusting headlamp pattern.................... 173
12
Adjusting the steering wheel...................... 76
AF – automatic frequency update........... 257
Airbag
activating/deactivating, PACOS........... 24
driver's and front passenger side......... 23
key switch off........................................ 24
Automatic locking.................................... 126
Auxiliary lamps........................................... 62
AUX input................................................. 248
Average fuel consumption......................... 68
All Wheel Drive, (AWD)............................. 150
AWD, All Wheel Drive............................... 150
Audio
headphones socket............................ 247
surround............................................. 251
B
AIRBAG ..................................................... 22
Audio, see also Sound............................. 245
Airbag system............................................ 22
Audio files................................................ 259
Air conditioning.......................................... 88
ECC...................................................... 91
rear of passenger compartment........... 61
audio system
functions............................................. 248
Backrest rear seat, lowering.................... 112
Audio volume
phone.......................................... 265, 276
phone/media player............................ 276
ring signal, phone............................... 276
Battery............................................. 220, 299
jump starting....................................... 163
maintenance............................... 209, 220
overload.............................................. 137
specifications...................................... 299
symbols on the battery....................... 220
Air conditioning system
repair................................................... 212
Air distribution............................................ 89
Air distribution, A/C................................... 92
Air quality system, ECC............................. 91
304
131
132
131
132
132
131
131
132
Automatic gearbox.......................... 147, 148
lock-up function.................................. 148
safety systems.................................... 149
towing and recovery........................... 161
trailer................................................... 165
W button............................................. 148
Auto, ECC.................................................. 92
Automatic car washes............................. 198
Backrest
front seat, lowering............................. 100
Bag holder............................................... 119
Blind spot (BLIS)...................................... 157
12 Alphabetical Index
BLIS................................................... 63, 157
Bluetooth
handsfree............................................ 274
mute microphone............................... 276
transfer call to mobile......................... 276
Bluetooth®
media.................................................. 250
streaming audio.................................. 250
Checking the engine oil level................... 213
C
Calls
functions during a call........................ 267
incoming............................................. 276
operation............................................. 276
Car care................................................... 198
Car care, leather upholstery.................... 200
Booster cushion, integrated...................... 42
Cargo area...............................................
bag holder...........................................
cargo area compartment....................
cargo cover.........................................
electrical socket..................................
lighting................................................
loading................................................
protective net......................................
safety grille..........................................
Bottle holder for rear seat passengers.... 108
Cargo area compartment........................ 120
Brakes
Anti-lock braking system, ABS........... 152
handbrake............................................. 75
Cargo cover............................................. 119
Boarding
rear seat.............................................. 112
Bonnet..................................................... 211
Bonnet, opening...................................... 211
Booster cushion
folding up.............................................. 42
lowering................................................ 43
Brake system........................................... 151
Bulbs, see Lighting.......................... 223, 299
115
119
120
119
119
105
116
117
118
Car upholstery......................................... 200
Car washing............................................. 198
Catalytic converter........................... 142, 298
Recovery............................................. 162
CD
changer............................................... 259
functions............................................. 259
Children..................................................... 34
child safety locks.................... 43, 61, 130
child seats and airbags......................... 34
child seats and side airbags................. 26
location in the car................................. 34
location in the car, table....................... 35
safety.................................................... 34
Child safety locks...................................... 61
Child seats.................................................
extra locking function in seatbelt..........
ISOFIX fixture system for child seats...
recommended......................................
size classes for child seats with the
ISOFIX fixture system...........................
upper mounting points for child seats..
34
47
43
35
12
43
47
Cigarette lighter socket.............................. 62
Cleaning
automatic car wash............................ 198
car washing........................................ 198
rims..................................................... 198
seatbelts............................................. 201
upholstery........................................... 200
water-repellent surface......................... 83
Clock, adjustment...................................... 55
Clutch fluid, checking & topping up........ 216
305
12 Alphabetical Index
Cold start
automatic gearbox.............................. 148
Detectors................................................... 62
Collision
inflatable curtain, IC.............................. 28
Diesel: engine preheater............................ 59
Colour code, paint................................... 202
Combined instrument panel...................... 55
12
Compass................................................... 79
calibration............................................. 82
setting the zone.................................... 79
Diesel particle filter.................................. 143
Direction indicators.................................... 67
Display, messages..................................... 60
Dolby Surround Pro Logic II.................... 244
Door mirrors............................................... 82
Condensation in headlamps.................... 198
Driver's door control panel.................. 54, 77
Coolant, checking and filling................... 215
Driving
cooling system....................................
economical.........................................
in water...............................................
slippery driving conditions..................
with a tailer.........................................
with the tailgate open.........................
Cooler box............................................... 111
Cooling system........................................ 137
Cruise control............................................ 73
Cup holder....................................... 108, 109
D
Deadlock
temporary deactivation....................... 129
Deadlocks
temporary deactivation of the alarm
detectors............................................. 132
Defroster.................................................... 93
306
Diesel....................................................... 142
E
ECC, electronic climate control........... 88, 91
Ecolabelling, FSC, owner's manual........... 13
Economical driving.................................. 136
ECO pressure.......................................... 183
table.................................................... 297
Electrical socket
cargo area........................................... 119
centre console...................................... 62
rear seat................................................ 76
137
136
136
138
165
137
Electrical system...................................... 299
Driving in water........................................ 136
Emission control
fault indicator........................................ 59
Driving with a trailer
towball load........................................ 288
towing capacity.......................... 165, 288
DSTC, see also Stability control
system............................................... 59, 153
operation............................................. 153
Emergency calls...................................... 264
Emergency equipment
warning triangle.................................. 184
Emergency puncture repair..................... 190
Engine compartment............................... 212
oil........................................................ 213
Engine oil......................................... 213, 292
adverse driving conditions.................. 292
capacities........................................... 292
filter..................................................... 213
12 Alphabetical Index
Engine preheater....................................... 59
Front seat
Lumbar............................................... 103
Massage............................................. 103
Engine specifications............................... 291
FSC, ecolabelling....................................... 13
EON - Enhanced Other Networks............ 258
Fuel
fuel consumption, display..................... 68
fuel economy...................................... 183
fuel filter.............................................. 143
parking heater....................................... 94
refuelling............................................. 139
oil grade.............................................. 292
oil pressure........................................... 58
Equalizer.................................................. 252
Expectant mothers, seatbelt...................... 19
External audio source
AUX-socket......................................... 248
USB connection.................................. 249
External dimensions................................ 288
F
Fan
ECC...................................................... 93
First aid equipment.................................. 186
Fluids, capacities..................................... 294
Fluids and oils.......................................... 294
Fluids and oils, checks, engine compartment......................................................... 213
Fluids and oils general............................. 209
Fog lamps
rear........................................................ 65
Fuelling
filling................................................... 141
fuel cap............................................... 141
Fuses.......................................................
box in cargo area................................
box in cargo area - Executive.............
box in passenger compartment..........
box in the engine compartment..........
changing.............................................
end box...............................................
General...............................................
230
238
240
234
232
230
236
230
G
Gearbox
automatic............................................ 147
General information on fuel..................... 141
Glovebox................................................. 107
Gross vehicle weight............................... 288
H
12
Handbrake................................................. 75
Hazard warning flashers............................ 63
Headlamp levelling.................................... 64
Headlamp pattern, adjusting................... 173
Headlamp pattern adjustment
Active Bending Lights (ABL) .............. 173
Halogen headlamp............................. 173
Headlamps
ABL....................................................... 65
off/on.................................................... 64
Headlamp washers.................................... 71
Headphones socket................................. 247
head restraint
centre seat, rear.................................. 113
307
12 Alphabetical Index
Heater
fuel-driven............................................. 94
Heating
front seats............................................. 63
rearview and door mirrors.............. 63, 93
rear window.................................... 63, 93
Interior lighting......................................... 104
L
Interior rearview mirror............................... 79
automatic dimming............................... 79
Lambda-sond.................................. 142, 298
Intermittent wiping..................................... 70
Lamps, see Lighting................................ 223
ISOFIX fixture system for child seats......... 43
Leather upholstery, washing instructions 200
High-pressure headlamp washing............. 71
12
Home safe lighting
setting................................................... 67
J
Jack......................................................... 185
Jacket holder........................................... 108
I
Jump starting........................................... 163
Ignition keys............................................. 146
IMEI number............................................ 269
Immobiliser...................................... 124, 146
Inflatable Curtain........................................ 28
Kerb weight.............................................. 288
Information display.................................... 60
Key........................................................... 124
remote control key.............................. 124
Infotainment system................................ 244
Inlaid mats............................................... 101
Instrument lighting..................................... 65
Instrument overview
left-hand drive car................................ 50
right-hand drive car.............................. 52
Integrated booster cushion........................ 42
308
K
Keypad in the steering wheel............ 73, 246
Kick-down
automatic gearbox.............................. 149
Lighting.................................................... 223
Active Xenon headlamps................ 62, 65
automatic lighting, dipped beam.......... 64
automatic lighting, passenger compartment............................................. 105
bulbs, specifications........................... 299
cargo area........................................... 105
exterior.................................................. 64
headlamp levelling................................ 64
home safe lighting................................ 67
in passenger compartment................. 104
instrument lighting................................ 65
lighting panel, passenger compartment...................................................... 64
main/dipped beam............................... 64
position/parking lamps......................... 64
reading lamps..................................... 104
rear fog lamp........................................ 65
switching headlamp pattern right/lefthand traffic, ABL........................... 62, 173
Lighting, bulb replacement...................... 223
bulb holder, rear................................. 226
12 Alphabetical Index
bulb location front lamp......................
cargo area...........................................
courtesy lighting.................................
dipped beam halogen.........................
direction indicators.............................
front....................................................
main beam..........................................
main beam halogen............................
number plate lighting..........................
parking lamps.....................................
position lamps....................................
rear fog lamp......................................
side marker lamps..............................
Vanity mirror.......................................
224
229
228
224
225
223
225
225
228
225
225
228
225
229
Lubricants, capacities.............................. 294
M
Main and dipped beam
switching............................................... 67
Main beam "flash"..................................... 67
maintenance
Rustproofing....................................... 204
Maintenance............................................ 209
self-maintenance................................ 209
Making calls............................................. 276
Loading
cargo area........................................... 116
General....................................... 114, 116
load capacity...................................... 114
load carriers........................................ 114
roof load............................................. 114
Massage
front seat............................................. 103
Load on the roof...................................... 114
Menu structure
audio system...................................... 262
phone, menu options.......................... 271
phone, overview................................. 270
Locking/unlocking
glovebox.............................................
inside..................................................
outside................................................
tailgate................................................
127
127
126
127
Master key............................................... 124
Menus
audio system...................................... 246
Meters in the combined instrument panel
fuel gauge.............................................
outside temperature gauge..................
speedometer.........................................
tachometer...........................................
trip meter..............................................
55
55
55
55
55
Misting....................................................... 88
condensation in headlamps............... 198
rear window.......................................... 63
removing with defroster function.......... 93
12
Mobile phone
connect............................................... 277
handsfree............................................ 274
register phone..................................... 275
Mp3 functions.......................................... 259
Multi-filter........................................... 88, 143
MY KEY................................................... 246
N
News................................................ 254, 257
Messages in BLIS.................................... 159
Messages in the information display......... 60
Lubricants................................................ 294
309
12 Alphabetical Index
O
Oil, see also Engine oil....................... 58, 292
Oil level low.............................................. 213
One-key dial............................................. 267
Owner's manual, ecolabelling.................... 13
Oxyhydrogen gas.................................... 163
12
P
PACOS....................................................... 24
PACOS, switch.......................................... 24
Paintwork
colour code......................................... 202
damage and touch-up........................ 202
Panel vents in the door pillar..................... 89
Park Assist......................................... 62, 155
parking assistance sensors................ 156
Parking brake....................................... 59, 75
Parking heater
battery and fuel.....................................
general..................................................
symbols and display messages............
time setting...........................................
310
96
94
94
95
Parking lamps............................................ 64
Position lamps........................................... 64
Petrol grade............................................. 142
Power seat............................................... 101
Phone
call volume.......................................... 268
connect............................................... 277
controls............................................... 264
ending a call....................................... 266
handsfree............................................ 274
incoming call....................................... 276
last dialled numbers........................... 267
making calls................................ 266, 276
memory............................................... 268
messages........................................... 268
on/off.................................................. 265
one-key dial........................................ 267
phone book................................. 268, 277
phone book, shortcut......................... 277
receiving a call............................ 266, 276
register phone..................................... 275
shortcuts............................................. 266
SIM card............................................. 266
traffic safety........................................ 266
volume reduction during phone call... 265
Power steering fluid, checking and topping up..................................................... 216
Phone book............................................. 268
Phone system.......................................... 263
Pinch protection, sunroof.......................... 85
Polishing.................................................. 199
Power sunroof........................................... 84
Power windows.........................................
blocking................................................
passenger seat.....................................
rear seat................................................
77
78
78
78
Protective grille........................................ 118
Protective net........................................... 117
PTY – Programme type........................... 255
Puncture, see Tyres......................... 185, 187
R
Radio
alarm................................................... 255
AUTOSTORE...................................... 253
EON.................................................... 258
frequency update................................ 257
news........................................... 254, 257
PTY..................................................... 255
radio settings...................................... 253
radio stations...................................... 253
12 Alphabetical Index
radio text.............................................
regional...............................................
storing stations...................................
traffic information................................
tuning..................................................
volume control, programme types.....
255
257
253
255
254
254
Recirculation
ECC...................................................... 92
S
Refrigerant............................................... 212
Scan
radio stations...................................... 254
Radio functions........................................ 253
Remote control........................................ 124
replacing the battery........................... 125
Radio text................................................ 255
Rain sensor................................................ 70
Random, CD and audio files.................... 260
RDS functions.......................................... 254
resetting.............................................. 258
Reading lamps......................................... 104
Rear centre console, removal.................. 112
Rear seat
boarding............................................. 112
Rear seat, lowering.................................. 112
Rearview and door mirrors
compass...............................................
door......................................................
electrically retractable...........................
heating..................................................
interior...................................................
retractable.............................................
79
82
82
63
79
61
Rear window, defrosting............................ 63
REG - Regional radio programmes......... 257
Relay/fuse box, see Fuses....................... 230
Remote control key
functions............................................. 124
Remote control key system, type approval............................................................ 301
Retractable power door mirrors (option)... 61
RND – Random........................................ 260
Roll-over protection
ROPS (Roll Over Protection System).... 31
Seatbelt
pregnancy............................................. 19
Seatbelt reminder...................................... 19
Seatbelts.................................................... 18
seatbelt tensioner................................. 19
Seats
heating.................................................. 63
lowering the front backrest................. 100
lowering the rear backrest.................. 112
manual setting.................................... 100
power seat.......................................... 101
Service programme................................. 208
Roof load................................................. 114
Side airbag, SIPS....................................... 26
ROPS (Roll Over Protection System)......... 31
SIM card.................................................. 266
double................................................. 269
Rustproofing............................................ 204
12
SIPS bag – decal....................................... 26
SIPS bags.................................................. 26
Sliding seat.............................................. 112
SMS......................................................... 268
write.................................................... 268
Soot filter........................................... 60, 143
311
12 Alphabetical Index
SOOT FILTER FULL................................. 143
Storage compartment...................... 109, 110
Sound
audio settings............................. 245, 251
audio source............................... 245, 248
Storage spaces in the passenger compartment.................................................. 106
spare wheel............................................. 185
Streaming audio...................................... 250
Spare wheel
temporary spare................................. 184
Sunroof......................................................
opening and closing.............................
pinch protection....................................
sunscreen.............................................
ventilation position................................
Speed dial numbers................................. 267
12
Spin control............................................. 153
Spin Control............................................. 153
SRS system
general.................................................. 22
Stability system....................................... 153
deactivation........................................ 153
indicator................................................ 59
symbols.............................................. 153
Stains....................................................... 200
Standby mode, phone............................. 265
Starting the engine.................................. 145
Steering lock............................................ 145
Steering wheel
cruise control........................................ 73
keypad.......................................... 73, 246
steering wheel adjustment.................... 76
Stone chips and scratches...................... 202
312
Storing radio stations............................... 253
T
Tailgate
driving with open tailgate................... 137
Locking/unlocking.............................. 124
Open................................................... 128
84
84
85
85
84
Technical data, engine............................. 291
Sunscreen, sunroof.................................... 85
Tools........................................................ 185
surround.................................................. 251
Towbar............................................. 165, 169
Switching
main and dipped beam......................... 67
Towbar, see Towing equipment.............. 167
Symbols
indicator symbols................................. 58
stability system................................... 153
warning symbols................................... 57
Temperature
actual temperature............................... 88
Temperature control.................................. 93
Towing..................................................... 161
towing eye.......................................... 161
Towing bracket........................................ 165
specifications...................................... 168
Towing capacity............................... 165, 288
Towing equipment
general........................................ 165, 167
installation........................................... 169
removing............................................. 171
Towing eye.............................................. 161
TP – Traffic information.................... 255, 257
Traction control........................................ 153
12 Alphabetical Index
Traction control system........................... 153
Traffic information............................ 255, 257
Trailer....................................................... 165
cable................................................... 167
driving with a trailer............................ 165
V
Ventilation fan function.............................. 88
Vibration damper..................................... 167
Volume control......................................... 248
Trip computer............................................ 68
Type approval, remote control key system........................................................... 301
Type designation..................................... 286
Tyres
direction of rotation............................ 182
driving characteristics......................... 180
general................................................ 180
maintenance....................................... 180
pressure...................................... 183, 297
puncture repair................................... 190
specifications...................................... 180
speed ratings...................................... 180
tread wear indicators.......................... 181
winter tyres......................................... 182
USB, connection...................................... 249
187
189
187
182
185
Whiplash injury.......................................... 29
W
Warning lamp
stability and traction control system.. 153
Warning symbol, airbag system................ 21
Warning triangle....................................... 184
Washers
headlamps............................................
rear window..........................................
washer fluid, filling..............................
windscreen...........................................
WHIPS
child seat/booster cushion................... 29
whiplash injury...................................... 29
12
Windscreen washing.................................. 71
Windscreen wiper
rain sensor............................................ 70
Windscreen wipers.................................... 70
71
71
215
71
Water and dirt-repellent coating................ 83
Water-repellent surface, cleaning............ 200
Waxing..................................................... 199
U
Wheels
changing.............................................
installation...........................................
removal...............................................
snow chains........................................
spare wheel........................................
Winter tyres.............................................. 182
Wiper
rear window.......................................... 71
Wiper blades............................................
Cleaning..............................................
replacing, rear window.......................
replacing, windscreen.........................
218
218
218
218
Weights
kerb weight......................................... 288
trailer weight....................................... 165
Wheel rims
cleaning.............................................. 198
313
12 Alphabetical Index
12
314
Volvo Car Corporation TP 16886 (English Int.), AT 1346, Printed in Sweden, Göteborg 2013, Copyright © 2000-2013 Volvo Car Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement