2 - Rosch Computer
USER’S
MANUAL
PMB-472
ULV Celeron® M
Mini-ITX Motherboard
With VGA/Sound/2LAN
PMB-472 M1
Copyright Notice
PMB-472 Celeron® M
Mini-ITX Motherboard
With VGA /Sound/2LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted in June, 2005. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.
Contents
TABLE OF CONTENTS
CHAPTER
1-1
1-2
1-3
1-4
CHAPTER
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
2-23
2-24
2-25
2-26
1
INTRODUCTION
About This Manual ........................................................
System Specification ......................................................
Extra Industrial Application Features................................
Safety Precautions …………………………………….
2
1-2
1-3
1-6
1-6
HARDWARE CONFIGURATION
Jumper & Connector Quick Reference Table ................
Component Locations ....................................................
How to Set the Jumpers .................................................
COM Port Connector ……..…………………………...
COM4 RI/ Voltage Selection …………………………
RS232/422/485(COM2) Selection ................................
RS232/422/485(COM3) Selection …………………….
Keyboard or PS/2 Mouse Connector .....................…....
Reset Connector ............................................................
Hard Disk Drive LED Connector ..................................
Power Button …............................................................
External Speaker Connector ..........................................
Power LED Connector ……...........................................
External SMI Connector ……………………………….
Inverter Connector ……………………………………..
Clear CMOS Data Selection …………………………..
CPU Fan Connector ……………………………………
VGA Connector ………………….……………………
Hard Disk Drive Connector ...........................................
Floppy Disk Drive Connector .......................................
Printer Connector ..........................................................
Universal Serial Bus Connector ………………………
IRDA Connector ……………………………………….
LAN Connector ……………………………………….
USB & LAN Connector ………………………………
Wake-On-LAN Connector …………………………….
2-2
2-3
2-4
2-6
2-8
2-9
2-10
2-11
2-11
2-11
2-12
2-12
2-12
2-13
2-13
2-14
2-14
2-15
2-16
2-18
2-19
2-20
2-21
2-21
2-22
2-23
Contents
2-27
2-28
2-29
2-30
2-31
2-32
2-33
2-34
2-35
2-36
2-37
2-38
2-39
LVDS Connector ……………..………………………..
LVDS Panel Voltage Selection ………………………..
ATX Power Connector …………………………………
Sound Connector ……………………………………….
CD Audio-In Connector ………………………………..
Speaker Connector ……………………………………..
Memory Installation ……………………………………
PCI/Riser Card Selection ………………………………
Reset / NMI Selection……………………………………
CF Master/Slave Selection …………………………….
PCI Slot Signal Explanation …………………………...
PCI Riser Board Information …………………………..
Digital I/O Port …………………………………………
CHAPTER
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
SOFTWARE UTILITIES
Introduction …………..........................................….......
VGA Driver Utility ……………………………….……
Flash BIOS Update ..............................................….......
LAN Driver Utility …...........................................…......
Sound Driver Utility ……………………………………
Intel Chipset Software Installation Utility …..……..…..
USB2.0 Software Installation Utility …………………..
Watchdog Configuration ………………………………
CHAPTER
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
3
4
2-24
2-25
2-26
2-27
2-28
2-28
2-28
2-29
2-30
2-31
2-32
2-33
2-33
3-2
3-2
3-4
3-6
3-7
3-8
3-9
3-10
AWARD BIOS SETUP
Introduction ...................................................................
Entering Setup ...............................................................
The Standard CMOS Features ………............................
The Advanced BIOS Features .......................................
Advanced Chipset Features ...........................................
Integrated Peripherals …...............................................
Power Management Setup .............................................
PNP/PCI Configuration ….............................................
PC Health Status ……....................................................
Frequency Control ....................................…………......
4-2
4-3
4-4
4-7
4-9
4-12
4-17
4-19
4-21
4-22
Contents
4-11
4-12
4-13
4-14
4-15
Load Fail-Safe Defaults .................................................
Load Optimized Defaults .........................................….
Set Supervisor Password ………………………………
Save & Exit Setup .........................................................
Exit Without Saving
…………………………………
APPENDIX
A
EXPANSION BUS
PCI Bus Pin Assignment ..............................................….........
Mini-PCI Bus Connector Pin Assignment ...................................
Compact Flash Card Connector Pin Assignment …………….
APPENDIX
B
4-23
4-23
4-24
4-25
4-26
A-2
A-3
A-4
TECHNICAL SUMMARY
Block Diagram ...........................................................................
Interrupt Map ............................................................................
RTC & CMOS RAM Map ........................................................
Timer & DMA Channels Map ..................................................
I/O & Memory Map ...............................................…................
B-2
B-3
B-4
B-5
B-6
CHAPTER
INTRODUCTION
1
This chapter gives you the information for PMB-472. It also
outlines the System specifications.
Section includes:
z About This Manual
z System Specifications
z Extra Industrial Application Features
z Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PMB-472 ULV Celeron-M Mini-ITX
Mainboard enhanced with VGA/Sound/2LAN, which is fully PC / AT
compatible. The PMB-472 provides faster processing speed, greater
expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the system. It contains four
chapters. The user can apply this manual for configuration according to the
following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to configure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for Mini-PCI BUS, and
PCI BUS.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Page: 1-2
PMB-472 USER′S MANUAL
Chapter
1
Introduction
1-2. SYSTEM SPECIFICATIONS
z CPU (mPGA479):
Intel® Celeron® M processor.
ULV 600MHz (non L2 cache).
Auto detect voltage regulator.
z MEMORY :
Supports up to 1GB DDR SDRAM.
One 200-pin DDR SO-DIMM sockets on board.
z CACHE :
Built-in CPU
z REAL-TIME CLOCK :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover.
z BIOS :
Phoenix-AwardBIOS™ for plug & play function.
4Mb with VGA BIOS.
Easy update 512KB flash EEPROM.
Support S/IO Setup.
z KEYBOARD CONNECTOR :
Mini DIN connector.
Supports for AT/PS2 keyboard.
z MOUSE CONNECTOR :
Mini DIN connector.
Supports for PS/2 Mouse.
z BUS SUPPORT :
One PCI- Slot
One Mini-PCI Slots
One Compact Flash Bus (for secondary IDE-based)
PMB-472 USER′S MANUAL
Page: 1-3
Chapter
1
Introduction
z DISPLAY :
Integrated Graphic in Intel® 852GM
Support D-Sub 15 pin VGA connector
Support 18/24bit LVDS connector
Support 3.3V/5V LVDS Panel Power selection
Support 12V Panel Backlight
*24bit hardware is ready but Intel does not recommend using.
z IDE INTERFACE :
Two IDE ports support up to four IED devices.
Supports Ultra DMA 33/66/100.
Compact Flash is connected at secondary IDE Bus.
Compact Flash Master/Slave Mode Selectable.
z FLOPPY DISK DRIVER INTERFACE :
Support Floppy Disk Drives 3.5".
z USB CONNECTOR :
Support up to six USB 2.0 ports.
z LAN ADAPTER :
Dual ports, Realtek RTL8100C (10/100 Mbps)
Support wake-on-LAN function.
z SERIAL PORT :
Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs; COM1:RS-232; COM2/3: RS-232/422/485; COM4: RS-232 with
+12V/+5V
MIDI Compatible
Programmable Baud Rate Generator
z SOUND :
Realtek ALC655 (AC’97 Codec).
Fully Compliant AC’97 Analog I/O Component
16-Bit Stereo Full-Duplex Codec
Four Analog Line-level Stereo Inputs for Connection.
High Quality CD Input with Ground Sense
Stereo Line-Level Output
Interface: Line-In, Line-Out, Microphone, SPDIF, and CD Audio-In.
Page: 1-4
PMB-472 USER′S MANUAL
Chapter
1
Introduction
z PCI :
Expandable up to 3 PCI slot by install a PCI riser card.
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming (only
under DOS system).
z IRDA PORT :
5-pin Infrared port, support IrDA v1.0 SIR protocol
z PARALLEL PORT :
SPP / ECP / EPP Function.
1 port, bi-directional parallel port.
z LED INDICATOR :
System power
Hard Disk access
LAN LED indicator
z OPERATING TEMPERATURE :
0 to 60°C.
z BOARD DIMENSIONS :
170mm x 170 mm, 6.7” x 6.7”
z BOARD NET WEIGHT :
460 gram.
PMB-472 USER′S MANUAL
Page: 1-5
Chapter
1
Introduction
1-3. EXTRA INDUSTRIAL APPLICATION FEATURES
z DIGITAL I/O PORT :
4 bit input and 4 bit output digital port availability.
Decoding Address at I/O 440H and 441H.
General purpose and Input/Output buffer embedded.
z WATCHDOG TIMER :
Watchdog Timer controllable by software, customer application 1~255 second
watchdog timer time-out value
Reset upon Mouse/Keyboard, SMI or System Reset.
1-4. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
Page: 1-6
PMB-472 USER′S MANUAL
HARDWARE
CONFIGURATION
CHAPTER
2
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
Page 2-1
Chapter
2
Hardware Configuration
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector
....................…..................………
…………………………………..
COM4 Port RI/Voltage Selection ……………………..
RS232/422/485 (COM2) Selection .....................………
RS232/422/485 (COM3) Selection …………………….
Keyboard/Mouse Connector ..........….....………………
Reset Connector .........................…....................……….
Hard Disk Drive LED Connector .......................……….
Power Button …………………………………………..
External Speaker Connector ....…........................………
Power LED Connector …………….…...............………
External SMI Connector ………………………………..
Inverter Connector ……………………………………..
Clear CMOS Data Selection ……………………………
CPU Fan Connector ……………………………………
VGA Connector …................……..……………………
Hard Disk Drive Connector …..............…….........…….
Floppy Disk Drive Connector ….............…….......…….
Printer Connector …........................…...…….........……
Universal Serial Bus Connector …........................…..…
IrDA Connector ………………………………………..
USB&LAN Connector …....................................………
LAN Connector ………………………………………...
Wake-on-LAN Connector ……………………………...
LVDS Connector ………………………………………
LVDS Voltage Selection ………………………………
Power Connector ………………………………………
Sound Connector ………………………….……………
CD Audio-In Connector ………………………………..
Speaker Connector ……………………………………..
Memory Installation ..................................…......………
PCI/Riser Card Selection ………………………………
Reset/NMI Selection …………………………………...
CF Master/Slave Selection ……………………………..
PCI Slot Signal Explanation
PCI Riser Board Information
Digital I/O Port …………………………………………
Page: 2-2
COM1, COM2
COM3, COM4
JP1
JP10
JP8
JKBMS1
JPANEL1 (13,15)
JPANEL1 (9,11)
JPANEL1 (14,16)
JPANEL1 (1,3,5,7)
JPANEL1 (8,10,12)
JPANEL1 (2, 4)
INV1
JP7
JCFAN1
VGA1
IDE1, IDE2
FDD1
JPRNT1
JUSB1, JUSB2
IRDA1
J2
LAN2
JWOL1, JWOL2
LVDS1
JP5
CN1
JAUDIO1
JCDIN2
SPK1
SO-DIMM1
JP6
JP9
JP3
DIO1
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-2. COMPONENT LOCATIONS
PMB-472 Connector, Jumper and Component locations
PMB-472 USER′S MANUAL
Page: 2-3
Chapter
2
Hardware Configuration
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open" or "close" pins.
The jumper can be combined into sets that called jumper blocks. When
the jumpers are all in the block, you have to put them together to set up
the hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You
can either connect PIN2 & PIN3 to create another setting. The same
jumper diagrams are applied all through this manual. The figure below
shows what the manual diagrams look and what they represent.
Page: 2-4
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
JUMPER DIAGRAMS
Jumper Cap
looks like this
2 pin Jumper
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
2 pin Jumper close(enabled)
Looks like this
1
1
3 pin Jumper
2-3 pin close(enabled)
Looks like this
1
1
Jumper Block
1-2 pin close(enabled)
Looks like this
1 2
PMB-472 USER′S MANUAL
1
2
Page: 2-5
Chapter
2
Hardware Configuration
2-4. COM PORT CONNECTOR
COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
ASSIGNMENT
DCD1
RX1
TX1
DTR1
GND
DSR1
RTS1
CTS1
RI1
COM2 : COM2 Connector
COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
Page: 2-6
RS-232
DCD2
RX2
TX2
DTR2
GND
DSR2
RTS2
CTS2
RI2
ASSIGNMENT
RS-422
RS-485
TXTXTX+
TX+
RX+
RX+
RXRXGND
GND
RTSNC
RTS+
NC
CTS+
NC
CTSNC
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
COM3 : COM3 Connector
COM3 is selectable as RS-232/422/485.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
RS-232
DCD3
RX3
TX3
DTR3
GND
DSR3
RTS3
CTS3
RI3
ASSIGNMENT
RS-422
RS-485
TXTXTX+
TX+
RX+
RX+
RXRXGND
GND
RTSNC
RTS+
NC
CTS+
NC
CTSNC
COM4 : COM4 Connector
COM4 is fixed as RS-232.
The pin assignment is as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
DCD4
RX4
TX4
DTR4
GND
DSR4
RTS4
CTS4
RI4
NC
PMB-472 USER′S MANUAL
Page: 2-7
Chapter
2
Hardware Configuration
2-5. COM4 PIN 9 RI OR VOLTAGE SELECTION
JP1 : COM4 Pin 9 RI or Voltage Selection
The selections are as follows:
SELECTION
JUMPER
SETTINGS
RI
1-2
+12V
3-4
+5V
5-6
JUMPER
ILLUSTRATION
***Manufacturing Default – RI.
If COM4’s Pin 9 is selectable to voltage mode, only 0.5Amp power
consumption is allowed for connected to COM device.
Page: 2-8
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-6. RS232/422/485 (COM2) SELECTION
JP10 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :
COM 2
Function
Jumper Settings
(pin closed)
RS-232
Open
RS-422
1-2, 3-4, 9-10
RS-485
1-2, 5-6, 9-10
Jumper
Illustrations
*** Manufactory default --- RS-232.
PMB-472 USER′S MANUAL
Page: 2-9
Chapter
2
Hardware Configuration
2-7. RS232/422/485 (COM3) SELECTION
JP8 : RS-232/422/485 (COM3) Selection
This connector is used to set the COM3 function.
The jumper settings are as follows :
COM 3
Function
Jumper Settings
(pin closed)
RS-232
Open
RS-422
1-2, 3-4, 9-10
RS-485
1-2, 5-6, 9-10
Jumper
Illustrations
*** Manufactory default --- RS-232.
Page: 2-10
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-8. KEYBOARD AND PS/2 MOUSE CONNECTOR
JKBMS1 : Keyboard and PS/2 Mouse Connector
DIN connector can support keyboard, and PS/2 Mouse. The pin
assignments are as follows :
PIN
1
2
3
4
5
6
ASSIGNMENT
Keyboard
PS/2 Mouse
KBDATA
MSDATA
NC
NC
GND
GND
5VSB
5VSB
KBCLK
MSCLK
NC
NC
2-9. RESET CONNECTOR
JPANEL1 (13,15) : Reset Connector.
The pin assignment is as follows :
PIN
13
15
ASSIGNMENT
GND
RST_SW
2-10. HARD DISK DRIVE LED CONNECTOR
JPANEL1 (9,11) : Hard Disk Drive LED Connector
The pin assignment is as follows :
PIN
9
11
ASSIGNMENT
HD_LED+
HD_LED-
PMB-472 USER′S MANUAL
Page: 2-11
Chapter
2
Hardware Configuration
2-11. POWER BUTTON
JPANEL1 (14,16) : Power Button
The pin assignment is as follows :
PIN
14
16
ASSIGNMENT
PWR_BN1
PWR_BN2
2-12. EXTERNAL SPEAKER CONNECTOR
JPANEL1 (1,3,5,7) : External Speaker Connector
The pin assignment is as follows :
PIN
1
3
5
7
ASSIGNMENT
SPKNC
NC
SPK+
2-13. POWER LED CONNECTOR
JPANEL1 (8,10,12) : Power LED Connector
The pin assignment is as follows:
PIN
8
10
12
Page: 2-12
ASSIGNMENT
PW_LED+
PW_LED+
PW_LED-
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-14. EXTERNAL SMI CONNECTOR
JPANEL1 (2,4) : External SMI Connector
The pin assignment is as follows:
PIN
2
4
ASSIGNMENT
GPIO12
GND
2-15. INVERTER CONNECTOR
INV1 : Inverter Connector
The pin assignment is as follows:
PIN
1
2
3
4
5
ASSIGNMENT
+12V
GND
VCC
GND
ENABKL (Inverter backlight
ON/OFF control signal)
PMB-472 USER′S MANUAL
Page: 2-13
Chapter
2
Hardware Configuration
2-16. CLEAR CMOS DATA SELECTION
JP7 : Clear CMOS Data Selection
The selections are as follows :
FUNCTION
JUMPER SETTING
(pin closed)
Normal
1-2
Clear CMOS
2-3
JUMPER
ILLUSTRATION
*** Manufacturing Default is set as Normal.
Note: To clear CMOS data, user must power-off the computer and set the jumper
to “Clear CMOS” as illustrated above. After five to six seconds, set the
jumper back to “Normal” and power-on the computer.
2-17. CPU FAN CONNECTOR
JCFAN1 : CPU Fan connector
The pin assignment is as follows:
PIN
1
2
3
Page: 2-14
ASSIGNMENT
GND
+12V
FAN1
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-18. VGA CONNECTOR
VGA1 : VGA CRT Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
RED
GREEN
BLUE
NC
GND
GND
GND
GND
VCC
GND
NC
VGA IIC DATA
HSYNC
VSYNC
VGA IIC CLK
PMB-472 USER′S MANUAL
Page: 2-15
Chapter
2
Hardware Configuration
2-19. HARD DISK DRIVE CONNECTOR
IDE1: Hard Disk Drive Connector
The PMB-472 possesses two HDD connectors, IDE1 and IDE2. The pin
assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
Page: 2-16
ASSIGNMENT
IDERST
PDD7
PDD6
PDD5
PDD4
PDD3
PDD2
PDD1
PDD0
GND
PDREQ
PDIOW#
PDIOR#
PIORDY
PDDACK#
IRQ14
PDA1
PDA0
PDCS#1
IDEACTP#
VCC
GND
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
ASSIGNMENT
GND
PDD8
PDD9
PDD10
PDD11
PDD12
PDD13
PDD14
PDD15
NC
GND
GND
GND
PULL LOW
GND
NC
P66 DETECT
PDA2
PDCS#3
GND
VCC
GND
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
IDE2: Hard Disk Drive Connector
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
ASSIGNMENT
IDERST
SDD7
SDD6
SDD5
SDD4
SDD3
SDD2
SDD1
SDD0
GND
SDREQ
SDIOW#
SDIOR#
SIORDY
SDDACK#
IRQ15
SDA1
SDA0
SDCS#1
IDEACTS#
PMB-472 USER′S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
ASSIGNMENT
GND
SDD8
SDD9
SDD10
SDD11
SDD12
SDD13
SDD14
SDD15
NC
GND
GND
GND
PULL LOW
GND
NC
S66 DETECT
SDA2
SDCS#3
GND
Page: 2-17
Chapter
2
Hardware Configuration
2-20. FLOPPY DISK DRIVE CONNECTOR
FDD1 : Floppy Disk Drive Connector
The pin assignments are as follows :
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
Page: 2-18
ASSIGNMENT
VCC
VCC
VCC
NC
NC
NC
DRVDEN0
GND
GND
GND
GND
GND
GND
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
ASSIGNMENT
INDEXJ
DSAJ
DSKCHGJ
NC
MOAJ
DIRJ
STEPJ
WDATAJ
WGATEJ
TRACK0J
WPTJ
RDATAJ
HEADJ
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-21. PRINTER CONNECTOR
JPRNT1 : Printer Connector
As to link the Printer to the card, you need a cable to connect both
DB25 connector and parallel port.
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
ASSIGNMENT
STB
PDR0
PDR1
PDR2
PDR3
PDR4
PDR5
PDR6
PDR7
ACK#
BUSY
PE
SLCT
PMB-472 USER′S MANUAL
PIN
14
15
16
17
18
19
20
21
22
23
24
25
ASSIGNMENT
AFD#
ERROR#
PAR_INIT#
SLIN#
GND
GND
GND
GND
GND
GND
GND
GND
Page: 2-19
Chapter
2
Hardware Configuration
2-22. UNIVERSAL SERIAL BUS CONNECTOR
JUSB1: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
VCCUSB2
VCCUSB2
USB2N_R
USB3N_R
USB2P_R
USB3P_R
GND
GND
GND
GND
JUSB2: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-20
ASSIGNMENT
VCCUSB3
VCCUSB3
USB4N_R
USB5N_R
USB4P_R
USB5P_R
GND
GND
GND
GND
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-23. IRDA CONNECTOR
IRDA1: IrDA (Infrared) Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
ASSIGNMENT
+5V
NC
IRRX
GND
IRTX
2-24. LAN CONNECTOR
LAN2: LAN Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
LAN2_TXP_R
2VDD33
LAN2_TXN_R
LAN2_ACT_R
GND
LAN2_LINK100_R
LAN2_RXP_R
LAN2_LINK10_R
LAN2_RXN_R
NC
PMB-472 USER′S MANUAL
Page: 2-21
Chapter
2
Hardware Configuration
2-25. USB&LAN CONNECTOR
J2: USB & LAN Connector (10/100 LAN)
The pin assignments are as follows:
LAN:
PIN
1
2
3
4
5
6
7
8
ASSIGNMENT
MDI_0P
MDI_0N
MDI_1P
MDI_1N
MDI_2P
MDI_2N
MDI_3P
MDI_3N
LAN LED Indicator:
Left side LED:
Green Color on
10/100 LAN Speed Indicator
Orange Color on Giga LAN Speed Indicator
off
No LAN switch/hub connected
Right side LED:
Yellow Color Blinking
off
USB:
PIN
A1
A2
A3
A4
B1
B2
B3
B4
Page: 2-22
LAN Message Active
No LAN Message Active
ASSIGNMENT
VCCUSB1
USB1N_R
USB1P_R
GND
VCCUSB0
USB0N_R
USB0P_R
GND
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-26. WAKE-ON-LAN CONNECTOR
JWOL1: Wake-On-LAN Connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
5VSB
GND
LWAKE
JWOL2: Wake-On-LAN Connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
5VSB
GND
PMEJ
PMB-472 USER′S MANUAL
Page: 2-23
Chapter
2
Hardware Configuration
2-27. LVDS CONNECTOR
LVDS1 : LVDS Connector.
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
Page: 2-24
ASSIGNMENT
LCD_VCC
ZCM
GND
Z2P
Z1M
Z3P
Z0P
GND
YCM
Y2P
GND
Y1M
Y0P
Y3P
LCD_VCC
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
ASSIGNMENT
GND
ZCP
Z2M
GND
Z1P
Z3M
Z0M
YCP
GND
Y2M
Y1P
GND
Y0M
Y3M
LCD_VCC
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-28. LVDS PANEL VOLTAGE SELECTION
JP5 : LVDS Panel Voltage Selection.
The selections are as follows:
SELECTION
LVDS_VCC3
LVDS_VCC5
JUMPER SETTING
JUMPER
ILLUSTRATION
1-3
2-4
3-5
4-6
** Manufacturing Default: LVDS_VCC3**
PMB-472 USER′S MANUAL
Page: 2-25
Chapter
2
Hardware Configuration
2-29. ATX POWER CONNECTOR
CN1 : ATX Power Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-26
ASSIGNMENT
VCC
VCC
GND
GND
+12V
5VSB
VCC
GND
PS-ON
-12V
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-30. SOUND CONNECTOR
JAUDIO1 : Sound Connector, including Line-In, Line-Out & Mic.
Also can support only MIC connector. The pin assignments are as
follows :
SPDIF (inside the Line-In hole)
PIN ASSIGNMENT
#
Photo type
Line-In: light blue color
PIN ASSIGNMENT
1
GND
2
LINE_L
3
LINE_R
SPK-Out: light green color
PIN ASSIGNMENT
1
GND
2
SPK_L
3
SPK_R
Mic-In: pink color
PIN ASSIGNMENT
1
GND
2
MIC_IN1
3
MIC_IN2
PMB-472 USER′S MANUAL
Page: 2-27
Chapter
2
Hardware Configuration
2-31. CD AUDIO-IN CONNECTOR
JCDIN2 : CD Audio-In Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
CD L
CDGND
CDGND
CD R
2-32. SPEAKER CONNECTOR
SPK1 : Speaker Connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
SPK_L
GND
SPK_R
2-33. MEMORY INSTALLATION
PMB-472 CPU Card can support up to 1GB in one SODIMM sockets.
DRAM BANK CONFIGURATION
SO-DIMM
128MB
256MB
512MB
1GB
Page: 2-28
TOTAL MEMORY
128MB
256MB
512MB
1GB
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-34. PCI SLOT PIN 26 SELECTION
JP6 : PCI/Riser Card Selection.
The selections are as follows:
SELECTION
PCI
(IDSEL)
Riser Card
(P_GNT#5)
JUMPER SETTING
JUMPER
ILLUSTRATION
1-2
2-3
** Manufacturing Default: Riser Card**
PMB-472 USER′S MANUAL
Page: 2-29
Chapter
2
Hardware Configuration
2-35. RESET/ NMI SELECTION
JP9 : Reset/NMI Selection.
The selections are as follows:
SELECTION
JUMPER SETTING
Reset
1-2
NMI
3-4
JUMPER
ILLUSTRATION
** Manufacturing Default: Reset**
Page: 2-30
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-36. CF MASTER/ SLAVE SELECTION
JP3 : CF Master/ Slave Selection.
The selections are as follows:
SELECTION
JUMPER SETTING
Master
1-2
Slave
Open
JUMPER
ILLUSTRATION
** Manufacturing Default: Master**
PMB-472 USER′S MANUAL
Page: 2-31
Chapter
2
Hardware Configuration
2-37. PCI SLOT SIGNAL EXPLANATION
In order to support standard PCI and PCI riser board for up to 3 PCI
devices, the PCI slot signals in this mainboard are listed below:
PIN
A1
A9
A11
A14
A19
A26
A40
A41
B2
B9
B10
B11
B14
B16
Page: 2-32
Standard
TRST#
RSVD
RSVD
RSV->3VSB
PME#
IDSEL
SMBCLK
SMBDATA
TCK
PRSNT1#
RSVD
PRSNT2#
RSVD
CLK
Riser
SERIRQ
CLKC
CLKD
GNT1#
REQ2#
GNT2#
REQA#
GNTA#
ISA_CLK
REQ3#
REQ1#
GNT3#
CLKA
CLKB
PMB-472 USER′S MANUAL
Chapter
2
Hardware Configuration
2-38. PCI RISER BOARD INFORMATION
For correctly operation for 3 PCI devices on the PCI slot of
the particular PCI riser card must be followed to the
recommendation. Professional technical consultant may
designing the right riser board or purchasing from
manufactories’ riser board.
PMB-472,
following
need for
the same
PCI Routing Table
IDSEL
AD28
AD29
AD30
INTJ0
A
B
C
INTJ1
B
C
D
INTJ2
C
D
A
INTJ3
D
A
B
REQ#
P_REQJ3
P_REQJ4
P_REQJ5
GNT#
P_GNTJ3
P_GNTJ4
P_GNTJ5
CLK
PCI_CLK3
PCI_CLK4
PCI_CLK5
2-39. DIGITAL I/O PORT
DIO1 : Digital Input/Output Port
The pin assignments are as follows:
PIN
ASSIGNMENT
1
VCC
2
GND
3
Input bit 0
4
Output bit 0
5
Input bit 1
6
Output bit 1
7
Input bit 2
8
Output bit 2
9
Input bit 3
10
Output bit 3
Input Port: Read I/O 440H
Output Port: Write I/O 441H
PMB-472 USER′S MANUAL
Page: 2-33
SOFTWARE
UTILITIES
CHAPTER
3
This chapter comprises the detailed information of VGA driver, LAN
driver, and Flash BIOS update. It also describes how to install the
watchdog timer configuration.
Section includes:
z VGA Driver Utility
z Flash BIOS Update
z LAN Driver Utility
z Sound Driver Utility
z Intel® Chipset Software Installation Utility
z USB2.0 Chipset Software Installation Utility
z Watchdog Configuration
Page: 3-1
Chapter
3
Software Configuration
3-1. INTRODUCTION
Enclosed with our PMB-472 package is our driver utility, which may comes
in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user,
you will only need some of the files contained in the CD ROM disc, please
kindly refer to the following chart:
Filename
(Assume that CD ROM drive is D:)
D:\Driver\VGA
Purpose
Intel 852GM
For VGA driver installation
D:\Driver\FLASH
For BIOS update utility
D:\Driver\LAN
For LAN Driver installation
D:\Driver\Sound
Realtel ALC655 AC97
For Sound driver installation
D:\Driver\UTILITY
Intel® Chipset Software
Installation Utility
For Win 98SE, 2000, XP
D:\Driver\USB 2.0
USB 2.0 Software Installation
Utility
For Win 98SE, 2000, ME, XP
User should remember to install the Utility right after the OS fully installed.
3-2. VGA DRIVER UTILITY
The VGA interface embedded with our PMB-472 can support a wide range
of display. You can display CRT, LVDS simultaneously with the same
mode.
Page:3-2
PMB-472 USER′S MANUAL
Chapter
3
Software Configuration
1. Win 9X program
2. Win NT4.0 program
3. Win 2000 program
4. Win XP program
3-2-1. Installation of VGA Driver:
To install the VGA Driver, simply follow the following steps:
1.
2.
3.
4.
5.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 9X/NT4.0/2000/XP system, go to the directory
where VGA driver is located.
Click Setup.exe file for VGA driver installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
Under the Windows 98 system, after rebut computer, there will have two
error messages appear, “Can’t find ikch8xx.cat and isb8xx.cat”, just skip the
messages, they will not cause any effects.
PMB-472 USER′S MANUAL
Page:3-3
Chapter
3
Software Configuration
3-3. FLASH BIOS UPDATE
3-3-1. System BIOS Update:
Users of PMB-472 can use the program “Awdflash.exe” contained in the
Utility Disk for system BIOS and VGA BIOS update.
3-3-2. To update VGA BIOS for LCD Flat Panel Display:
As PMB-472 user, you have to update the VGA BIOS for your specific
LCD flat panel you are going to use. For doing this, you need two files.
One is the “Awdflash.exe” file and the other is the VGA BIOS for ATI
Rage Mobility M6 file for LCD panel display. Both file must be
provided by the vendor or manufacturer. When you get these two files
ready, follow the following steps for updating your VGA BIOS:
1.
2.
3.
4.
Install “Awdflash.exe” from Utility Disk to Drive C.
Insert the VGA BIOS file you have obtained from the vendor.
Type the path to Awdflash.exe and execute the VGA BIOS update
with file B472xxxx.bin
C:\UTIL\AWDFLASH>AWDFLASH B472xxxx.bin
The screen will display as the table fount on the next page:
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A /3.3V
File Name to Program: B472xxxx.bin
Checksum: XXXXX
Error Message:
Do You Want To Save BIOS (Y/N)
If you want to save up the original BIOS, enter "Y" and press < Enter >.
If you choose "N", the following table will appear on screen.
Page:3-4
PMB-472 USER′S MANUAL
Chapter
3
Software Configuration
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: B472xxxx.bin
Checksum: XXXXX
Error Message :
Are You Sure To Program (Y/N)
Select "Y", and the BIOS will be renewed. When you are refreshing the
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, the screen displays the
table below:
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: B472xxxx.bin
Checksum: XXXXX
Reset System or Power off to
accomplish update process!
F1: Reset
F10: Exit
Please reset or power off the system, and then the Flash BIOS is fully
implemented.
PMB-472 USER′S MANUAL
Page:3-5
Chapter
3
Software Configuration
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
PMB-472 is enhanced with LAN function that can support various
network adapters. Installation programs for LAN drivers are listed as
follows:
1. Win 98/2000/XP program
2. Linux program
For more details on Installation procedure, please refer to Readme.txt
file found on LAN DRIVER UTILITY.
Page:3-6
PMB-472 USER′S MANUAL
Chapter
3
Software Configuration
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The Realtek ALC655 sound function enhanced in this system is fully
compatible with Windows 98, Windows NT 4.0, Windows 2000, and
Windows XP. Below, you will find the content of the Sound driver :
1. Win 98SE program
2. Win NT 4.0 program
3. Win 2000 program
4. Win XP program
3-5-2. Installation Procedure for Windows 9x/NT/2000/XP
1.
2.
3.
4.
5.
From the task bar, click on Start, and then Run.
In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\pathname” refers to the full path to the source files.
Click on the OK button or press the ENTER key.
Click on the “Next” and OK prompts as they appear.
Reboot the system to complete the driver installation.
PMB-472 USER′S MANUAL
Page:3-7
Chapter
3
Software Configuration
3-6. INTEL® CHIPSET SOFTWARE INSTALLATION UTILITY
3-6-1. Introduction
The Intel® Chipset Software Installation Utility installs to the target
system the Windows* INF files that outline to the operating system how
the chipset components will be configured. This is needed for the
proper functioning of the following features:
-
Core PCI and ISAPNP Services
AGP Support
IDE/ATA33/ATA66/ATA100 Storage Support
USB Support
Identification of Intel® Chipset Components in Device Manager
3-6-2. Installation of Utility for Windows 98SE/2000/XP
The Utility Pack is to be installed only for Windows 98SE, Windows
2000 and XP program.
It should be installed right after the OS installation, kindly follow the
following steps:
1.
2.
3.
4.
5.
Page:3-8
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE/2000/XP system, go to the directory where
Utility Disc is located.
Click Setup.exe file for utility installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
PMB-472 USER′S MANUAL
Chapter
3
Software Configuration
3-7. USB2.0 SOFTWARE INSTALLATION UTILITY
3-7-1. Installation of Utility for Windows 98SE/ 2000/XP
Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 98SE, Windows 2000 and Windows XP on Intel Desktop
boards. It should be installed right after the OS installation, kindly
follow the following steps:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE, 2000, and XP system, go to the directory
where Utility Disc is located.
Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).
Select “Hardware” and click “Device Manager ” button.
Double Click “USB Root Hub”.
Select “Driver”.
Click “Install” to install the driver.
Follow the instructions on the screen to complete the installation.
Click “Finish” after the driver installation is complete.
PMB-472 USER′S MANUAL
Page:3-9
Chapter
3
Software Configuration
3-8. WATCHDOG TIMER CONFIGURATION
The I/O port address of the watchdog timer is 2E(hex) and 2F(hex). 2E (hex) is the
address port. 2F(hex) is the data port. User must first assign the address of register by
writing address value into address port 2E(hex), then write/read data to/from the
assigned register through data port 2F (hex).
Configuration Sequence
To program W83627HF configuration registers, the following configuration sequence
must be followed:
(1) Enter the extended function mode
(2) Configure the configuration registers
(3) Exit the extended function mode
(1) Enter the extended function mode
To place the chip into the extended function mode, two successive writes of 0x87
must be applied to Extended Function Enable Registers (EFERs, i.e. 2Eh).
(2) Configurate the configuration registers
The chip selects the logical device and activates the desired logical devices through
Extended Function Index Register (EFIR) and Extended Function Data Register
(EFDR). EFIR is located at the same address as EFER, and EFDR is located at
address (EFIR+1).
First, write the Logical Device Number (i.e.,0x07) to the EFIR and then write the
number of the desired logical device to the EFDR. Secondly, write the address of the
desired configuration register within the logical device to the EFIR and then write (or
read) the desired configuration register through EFDR.
(3) Exit the extended function mode
To exit the extended function mode, one write of 0xAA to EFER is required. Once
the chip exits the extended function mode.
Example Program
1. Enable watchdog timer and set 30 sec. as timeout interval
;----------------------------------------------------------Mov dx, 2eh ; Enter to extended function mode
Mov al, 87h
Out dx, al
Out dx, al
;----------------------------------------------------------Page:3-10
PMB-472 USER′S MANUAL
Chapter
3
Software Configuration
Mov al, 07h ; Select Logical Device 8 of watchdog timer
Out dx,al
Inc dx
Mov al, 08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set second as counting unit
Mov al, 0f5h
Out dx,al
Inc dx
In al,dx
And al,not 08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set timeout interval as 30seconds and start counting
Mov al, 0f6h
Out dx,al
Inc dx
Mov al, 30
Out dx,al
;----------------------------------------------------------Dec dx ; Exit the extended function mode
Mov al, 0aah
Out dx,al
PMB-472 USER′S MANUAL
Page:3-11
CHAPTER
AWARD
BIOS SETUP
4
This chapter shows how to set up the Award BIOS.
Section includes:
z Introduction
z Entering Setup
z The Standard CMOS Features
z The Advanced BIOS Features
z The Advanced Chipset Features
z Integrated Peripherals
z Power Management Setup
z PNP/PCI Configuration
z PC Health Status
z Frequency Control
z Load Fail-Safe Defaults
z Load Optimized Defaults
z Set Supervisor Password
z Set User Password
z Save and Exit Setup
z Exit Without Saving
Page: 4-1
Chapter
4
Award BIOS Setup
4-1. INTRODUCTION
This chapter will show you the function of the BIOS in managing the
features of your system. The PMB-472 Intel® Celeron® M Half Size Card is
equipped with the BIOS for system chipset from Award Software Inc. This
page briefly explains the function of the BIOS in managing the special
features of your system. The following pages describe how to use the BIOS
for system chipset Setup menu.
Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.
The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.
The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:
Page: 4-2
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:
PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST
As long as this message is present on the screen you may press the <Del>
key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
►Power Management Setup
Set User Password
►PnP/PCI Configurations
Save & Exit Setup
►PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
↑↓→← : Select Item
Time, Date, Hard Disk Type .…
Setup program initial screen
You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.
PMB-472 USER′S MANUAL
Page: 4-3
Chapter
4
Award BIOS Setup
4-3. THE STANDARD CMOS FEATURES
Highlight the〝STANDARD CMOS FEATURES〞and press the <ENTER>
key and the screen will display the following table:
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
▶
▶
▶
▶
Date (mm:dd:yy)
Time (hh:mm:ss)
Tue, Jun 21 2005
17 : 13 : 13
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
[QSI CD-ROM SCR-242]
[None]
[ST340014A]
[None]
Drive A
Drive B
[1.44M, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All, But Keyboard]
Base Memory
Extended Memory
Total Memory
640K
1013760K
1014784K
Item Help
Menu Level
↑↓→←: Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
►
Change the internal
clock.
ESC:Exit
F1:General Help
F7:Optimized Defaults
CMOS Setup screen
In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.
Date:
< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.
Time:
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.
Page: 4-4
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
IDE Primary Master / Slave:
IDE Secondary Master / Slave:
The BIOS can automatically detect the specifications and optimal operating
mode of almost all IDE hard drives. When you select type AUTO for a hard
drive, the BIOS detect its specifications during POST, every time system
boots.
If you do not want to select drive type AUTO, other methods of selecting
drive type are available:
1.
Match the specifications of your installed IDE hard drive(s) with the
preprogrammed values for hard drive types 1 through 45.
2.
Select USER and enter values into each drive parameter field.
3.
Use the IDE HDD AUTO DETECTION function in Setup.
Here is a brief explanation of drive specifications:
Type: The BIOS contains a table of pre-defined drive types. Each
defined drive type has a specified number of cylinders, number of heads,
write precompensation factor, landing zone, and number of sectors.
Drives whose specifications do not accommodate any predefine type are
classified as type USER.
•
Size: Disk drive capacity (approximate). Note that this size is usually
greater than the size of a formatted disk given by a disk-checking
program.
•
Cyls: number of cylinders.
•
Head: number of heads.
•
Precomp: write precompensation cylinders.
•
Landz: landing zone.
•
Sector: number of sectors.
•
Mode: Auto, Normal, Large or LBA.
Auto: The BIOS automatically determines the optimal mode.
ƒ
Normal: Maximum number of cylinders, heads, sectors
supported are 1024, 16 and 63.
ƒ
Large: For drives that do not support LBA and have more
than 1024 cylinders.
PMB-472 USER′S MANUAL
Page: 4-5
Chapter
4
Award BIOS Setup
ƒ
LBA (Logical Block Addressing): During drive accesses, the
IDE controller transforms the data address described by
sector, head and cylinder number into a physical block
address, significantly improving data transfer rates. For
drives greater than 1024 cylinders.
DRIVE A AND DRIVE B:
Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,
2.88MB 3.5in and None.
VIDEO:
This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters.
CGA 40
Color Graphics Adapter, power up in 40 column mode.
CGA 80
Color Graphics Adapter, power up in 80 column mode.
MONO
Monochrome adapter, includes high resolution
monochrome adapters.
HALT ON:
This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.
BASE MEMORY:
Displays the amount of conventional memory detected during boot up.
EXTENDED MEMORY:
Displays the amount of extended memory detected during boot up.
TOTAL MEMORY:
Displays the total memory available in the system.
Page: 4-6
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-4. THE ADVANCED BIOS FEATURES
Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen
shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
↑↓→←: Move
Enter: Select
F5: Previous Values
[Enabled]
[Enabled]
[USB-CDROM]
[HDD-0]
[Enabled]
[On]
[Disabled]
6
250
[Setup]
[Non-OS2]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
Item Help
Menu Level
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
BIOS Features Setup Screen
The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.
A brief introduction of each setting is given below.
CPU L1 & L2 CACHE :
This item allows you to enable L1 & L2 cache.
QUICK POWER ON SELF-TEST:
This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.
FIRST/SECOND/ BOOT DEVICE:
The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.
PMB-472 USER′S MANUAL
Page: 4-7
Chapter
4
Award BIOS Setup
BOOT UP FLOPPY SEEK:
You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.
BOOT UP NUMLOCK STATUS:
Select power on state for NumLock.
TYPEMATIC RATE SETTING:
Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.
TYPEMATIC RATE (CHARS/SEC):
This item sets the number of times a second to repeat a key stroke when you
hold the key down.
TYPEMATIC DELAY (MSEC):
The item sets the delay time after the key is held down before it begins to
repeat the keystroke.
SECURITY OPTION:
This category allows you to limit access to the system and Setup, or just to
Setup.
System
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
Setup
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
To disable security, select PASSWORD SETTING at Main Menu and
then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.
OS SELECT FOR DRAM >64MB :
Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.
Page: 4-8
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-5. ADVANCED CHIPSET FEATURES
Choose the〝ADVANCED CHIPSET FEATURES〞from the main menu,
the screen shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
X CAS Latency Time
X Active to Precharge Delay
X DRAM RAS# to CAS# Delay
X DRAM RAS# Precharge
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size (MB)
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
Boot Display
Panel Type
PCI SERR# NMI
↑↓→←: Move
Enter: Select
F5: Previous Values
[By SPD]
2
6
3
3
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[64]
Item Help
Menu Level
►
[Enabled]
[32MB]
[CRT]
[640x480 18-bits]
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Chipset Features Setup Screen
This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.
It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best operating conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.
PMB-472 USER′S MANUAL
Page: 4-9
Chapter
4
Award BIOS Setup
DRAM TIMING BY SELECTABLE:
This allows you to select the DRAM timing.
CAS LATENCY TIME:
When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.
ACTIVE TO PRECHARGE DELAY:
This item controls the number of DRAM clocks for TRAS.
DRAM RAS# TO CAS# DELAY:
This field let’s you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast gives
faster performance; and Slow gives more stable performance. This field
applies only when synchronous DRAM is installed in the system.
DRAM RAS# PRECHARGE:
If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system.
DRAM DATA INTEGRITY MODE:
Select Parity or ECC (error-correcting code), according to the type of installed
DRAM.
SYSTEM BIOS CACHEABLE:
Selecting Enabled allows caching of the system BIOS ROM at F0000hFFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.
VIDEO BIOS CACHEABLE:
Select Enabled allows caching of the video BIOS, resulting in better system
performance. However, if any program writes to this memory area, a system
error may result.
Page: 4-10
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
MEMORY HOLE AT 15M-16M:
You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses their
memory requirements.
DELAYED TRANSACTION:
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1.
AGP APERTURE SIZE:
This field determines the effective size of the Graphic Aperture used for a
particular GMCH configuration. It can be updated by the GMCH-specific
BIOS configuration sequence before the PCI standard bus enumeration
sequence takes place. If it is not updated then a default value will select an
aperture of maximum size.
ON-CHIP VGA :
By default, the On-Chip VGA or chipset-integrated VGA is “Enabled”.
ON-CHIP FRAME BUFFER SIZE: (depend on chipset)
The On-Chip Frame Buffer Size can be set as 1MB or 8MB. This memory is
shared with the system memory.
BOOT DISPLAY: (depend on chipset)
Boot Display determines the display output device where the system boots.
The options are CRT and LVDS.
PANEL TYPE: (depend on chipset)
This field allows user to decide the LVDS panel resolution. The available
choices are: 640x480 18bits, 800x600 18bits, 1024x768 18bits, 1280x1024
36bits, 1400x1050 36bits, 1600x1200 36bits, and 1024x768 24bits.
PMB-472 USER′S MANUAL
Page: 4-11
Chapter
4
Award BIOS Setup
4-6. INTEGRATED PERIPHERALS
Choose〝INTEGRATED PERIPHERALS〞from the main setup menu, a
display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
►OnChip IDE Device
►Onboard Device
►SuperIO Device
Watch Dog Timer Select
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
↑↓→←: Move
Enter: Select
F5: Previous Values
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
[3E8]
[IRQ10]
[2E8]
[IRQ11]
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
Integrated Peripherals Setup Screen
By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.
If bios setup menu item supports USB device boot, it will cause Win9x detects
the same storages twice when the system is rebooted, and USB HDD will fail.
Note: this cause just happen under Win9x, the phenomenon is a limitation.
Page: 4-12
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
ONCHIP IDE DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
OnChip IDE Device
OnChip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
OnChip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
IDE HDD Block Mode
[Enabled]
↑↓→←:Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. OnChip Primary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
2. Primary Master/Slave PIO
Secondary Master/Slave PIO
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of
the four IDE devices that the onboard IDE interface supports. Modes
0 through 4 provide successively increased performance. In Auto
mode, the system automatically determines the best mode for each
device.
3. Primary Master/Slave UDMA
Secondary Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver
(Windows 95 OSR2 or a third-party IDE bus master driver). If you
hard drive and your system software both support Ultra DMA/33,
select Auto to enable BIOS support.
PMB-472 USER′S MANUAL
Page: 4-13
Chapter
4.
5.
4
Award BIOS Setup
OnChip Secondary PCI IDE
Enable the secondary IDE channel.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or
multiple sector read/write. If your IDE hard drive supports block mode
(most new drives do), select Enabled for automatic detection of the
optimal number of block read/writes per sector the drive can support.
ONBOARD DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Support
USB Keyboard Support
USB Mouse Support
AC97 Audio
Onboard LAN
Init Display First
Onboard Lan2
↑↓→←:Move
Enter: Select
F5: Previous Values
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Enabled]
[Onboard]
[Enabled]
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. USB Controller
This should be enabled if your system has a USB installed on the
system board and you want to use it. Even when so equipped, if you
add a higher performance controller, you will need to disable this
feature.
2. USB 2.0 Support
Enable the USB 2.0 controller.
3. USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
4. USB Mouse Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB Mouse.
Page: 4-14
PMB-472 USER′S MANUAL
Chapter
5.
6.
7.
4
Award BIOS Setup
AC97 Audio
This item allows you to enable/disable to support AC97 Audio.
Onboard LAN
Enable onboard LAN chip.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip
VGA first.
SUPER IO DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
X RxD, TxD Active
X IR Transmission Delay
X UR2 Duplex Mode
X Use IR Pins
Onboard Parallel Port
Parallel Port Mode
X EPP Mode Select
X ECP Mode Use DMA
PWRON After PWR-Fail
↑↓→←:Move
Enter: Select
F5: Previous Values
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Hi, Lo
Enabled
Half
IR-Rx2Tx2
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. Onboard FDC Controller
Select Enabled if the system has a floppy disk controller (FDC) installed
on the system board and you wish to use it. If you install and-in FDC or
the system has no floppy drive, select Disabled.
2. Onboard Serial Port 1/2
Select an address and corresponding interrupt for the first and second
serial ports.
3. UART Mode Select
This item allows you to select UART mode.
PMB-472 USER′S MANUAL
Page: 4-15
Chapter
4
Award BIOS Setup
4.
RxD, TxD Active
This item allows you to determine the active of RxD, TxD.
5. IR Transmission Delay
This item allows you to enable/disable IR transmission delay.
6. UR2 Duplex Mode
This item allows you to select the IR half/full duplex function.
7. Use IR Pins
This item allows you to select IR transmission routes, one is RxD2m,
TxD2 (COM Port) and the other is IR-Rx2Tx2
8. Onboard Parallel Port
This item allows you to determine access onboard parallel port
controller with which I/O address.
9. Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port.
Select Normal, Compatible, or SPP unless you are certain your
hardware and software both support one of the other available modes.
10. EPP Mode Select
Select EPP port type 1.7 or 1.9.
11. ECP Mode Use DMA
Select a DMA channel for the parallel port for use during ECP mode.
12. PWRON After PWR-Fail
This item allows you to select if you want to power on the system after
power failure. The choice: Off, On, Former-Sts.
ONBOARD SERIAL PORT 3:
ONBOARD SERIAL PORT 4:
Select a logical COM port name and matching address for the third and
forth serial ports. Select an address and corresponding interrupt for third
and forth serial port.
SERIAL PORT 3 USE IRQ:
SERIAL PORT 4 USE IRQ:
The items set the IRQ address of the serial ports.
Page: 4-16
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-7. POWER MANAGEMENT SETUP
Choose〝POWER MANAGEMENT SETUP〞option on the main menu, a
display will be shown on screen as below :
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
[Enabled]
[User Define]
[DPMS]
[Yes]
[3]
[Disabled]
[Instant-Off]
[Enabled]
[Disabled]
0
0:0:0
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
MODEM Use IRQ
Suspend Mode
Soft-Off by PWR-BTTN
Wake-Up by PCI card
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
↑↓→←: Move
Enter: Select
F5: Previous Values
Item Help
Menu Level
►
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Power Management Setup Screen
The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.
ACPI FUNCTION:
This item allows the user to set the ACPI suspend type to be used.
POWER MANAGEMENT:
This item allows you to select the Power Management mode.
PMB-472 USER′S MANUAL
Page: 4-17
Chapter
4
Award BIOS Setup
VIDEO OFF METHOD:
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to the
video buffer.
Blank Screen
DPMS
This option only writes blanks to the video buffer.
Select this option if your monitor supports the Display
Power Management Signalling (DPMS) standard of the
Video Electronics Standards to select video power
management values.
MODEM USE IRQ:
This item enable you to name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always
awakens the system.
SUSPEND MODE:
When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.
SOFT-OFF BY PWR-BTTN:
Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.
WAKE-UP BY PCI CARD:
An input signal from PME on the PCI card awakens the system from a soft
off state.
RESUME BY ALARM:
When Enabled, your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from Suspend mode.
RELOAD GLOBAL TIMER EVENTS:
PM events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device
which is configured as Enabled, even when the system is in a power down
mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4)
Secondary IDE 1 (5) FDD, COM, LPT Port
Page: 4-18
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-8. PNP/PCI CONFIGURATION
Choose 〝PNP/PCI CONFIGURATION〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
x IRQ Resources
PCI/VGA Palette Snoop
↑↓→←: Move
Enter: Select
F5: Previous Values
[Disabled]
Item Help
[Auto (ESCD)]
Press Enter
Menu Level
Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
►
ESC:Exit
F1:General Help
F7:Optimized Defaults
PNP/PCI Configuration Setup Screen
The PNP/PCI Configuration Setup describes how to configure PCI bus system.
PCI, also known as Personal Computer Interconnect, is a system, which
allows I/O devices to operate at speeds nearing the speed of the CPU itself
uses when communicating with its own special components.
This section covers technical items, which is strongly recommended for
experienced users only.
RESET CONFIGURATION DATA:
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.
PMB-472 USER′S MANUAL
Page: 4-19
Chapter
4
Award BIOS Setup
RESOURCE CONTROLLED BY:
The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources and DMA Resources.
IRQ RESOURCES:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
IRQ Resources
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
↑↓→←:Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
Item Help
Menu Level ►
Legacy ISA for devices
compliant with the
original PC AT bus
specification, PCI/ISA
PnP for devices
compliant with the Plug
and Play standard
whether designed for
PCI or ISA bus
architecture
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
13. IRQ-n Assigned to:
You may assign each system interrupt a type, depending on the type of
device using the interrupt.
PCI/VGA PALETTE SNOOP:
Leave this field at Disabled.
Page: 4-20
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-9. PC HEALTH STATUS
Choose 〝PC HEALTH STATUS〞 from the main menu, a display will
be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Current Warning Temperature
Current CPU Temperature
Current SYSTEM Fan Speed
Vcore
Vccp
3.3 V
+5V
+12 V
-12 V
-5V
VBAT (V)
5VSB (V)
Shutdown Temperature
↑↓→←: Move
Enter: Select
F5: Previous Values
[Disabled]
48℃/118℉
0 RPM
1.00V
1.04V
3.28V
4.73V
11.43V
-11.78V
-4.79V
3.34V
5.09V
[Disabled]
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
PC Health Status Setup Screen
The PC Health Status Setup allows you to select whether to choose between
monitoring or to ignore the hardware monitoring function of your system.
CURRENT WARNING TEMPERATURE:
Select the combination of lower and upper limits for the CPU temperature.
If the CPU temperature extends beyond either limit, any warning
mechanism programmed into your system will be activated.
CURRENT CPU TEMPERATURE:
This item shows you the current CPU temperature.
CURRENT SYSTEM FAN SPEED:
This item shows you the current System FAN speed.
VCORE:
This item shows you the current system voltage.
PMB-472 USER′S MANUAL
Page: 4-21
Chapter
4
Award BIOS Setup
3.3V / +5V / +12V / -12V/ -5V/ VBAT/ 5VSB:
Show you the voltage of 3.3V/+5V/+12V/-12V/-5V/ VBAT/5VSB.
SHUTDOWN TEMPERATURE:
This item allows you to set up the CPU shutdown Temperature.
function is only effective under Windows 98 ACPI mode.
This
4-10. FREQUENCY CONTROL
Choose 〝FREQUENCY CONTROL〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Frequency Control
Auto Detect PCI Clk
Spread Spectrum
[Enabled]
[Enabled]
Item Help
Menu Level
↑↓→←: Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
►
F1:General Help
F7:Optimized Defaults
Frequency Control Setup Screen
This setup menu allows you to specify your settings for frequency control.
AUTO DETECT PCI CLK:
This item allows you to enable or disable auto detect PCI Clock.
SPREAD SPECTRUM:
When the system clock generator pulses, the extreme values of the pulse
generate excess EMI. Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some cases be outweighed by problems with timingcritical devices such as a clock-sensitive SCSI device.
Page: 4-22
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-11. LOAD FAIL-SAFE DEFAULTS
By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:
Load Fail-Safe Defaults ( Y/N ) ? N
To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.
4-12. LOAD OPTIMIZED DEFAULTS
When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:
Load Optimized Defaults ( Y/N ) ? N
Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.
PMB-472 USER′S MANUAL
Page: 4-23
Chapter
4
Award BIOS Setup
4-13. SET SUPERVISOR PASSWORD
User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.
TO SET A PASSWORD
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
Enter Password:
Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.
User should bear in mind that when a password is set, you will be
asked to enter the password everything you enter CMOS setup Menu.
TO DISABLE THE PASSWORD
To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:
PASSWORD DISABLED!!!
Press any key to continue...
Press the < Enter > key again and the password will be disabled.
password is disabled, you can enter Setup freely.
Page: 4-24
Once the
PMB-472 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-14. SAVE & EXIT SETUP
After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
word
►Power Management
►PnP/PCI Configura
Save to CMOS and EXIT Y/N)? Y
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
↑↓→← : Select Item
Save Data to CMOS
When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.
PMB-472 USER′S MANUAL
Page: 4-25
Chapter
4
Award BIOS Setup
4-15. EXIT WITHOUT SAVING
If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
word
►Power Management
►PnP/PCI Configura
Quit Without Saving (Y/N)? N
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
↑↓→← : Select Item
Abandon all Datas
Page: 4-26
PMB-472 USER′S MANUAL
APPENDIX
EXPANSION BUS
A
This appendix indicates the pin assignments.
Section includes:
z PCI BUS Pin Assignment
z Mini-PCI BUS Pin Assignment
z Compact Flash Card Connector Pin Assignment
Page: A-1
Appendix
A
Expansion Bus
PCI BUS PIN ASSIGNMENT
Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin.
The pin assignments are as follows :
B1
B49 B52
B62
A1
A49 A52
A62
B
A
B
A
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
-12V
TCK
GND
TDO
+5V
+5V
INTB#
INTD#
REQ3#
REQ1#
GNT3#
GND
GND
CLKA
GND
CLKB
GND
REQ0#
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
C/BE3#
AD23
GND
AD21
AD19
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
CLKC
+5V(I/O)
CLKD
GND
GND
GNT1#
RST#
+5V(I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
GNT2#
+3.3V
AD22
AD20
GND
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
+3.3V
AD17
C/BE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE1#
AD14
GND
AD12
AD10
GND
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V(I/O)
ACK64#
+5V
+5V
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
AD18
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
SDONE
SB0#
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
C/BE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V(I/O)
REQ64#
+5V
+5V
Page: A-2
PMB-472USER′S MANUAL
Appendix
A
Expansion Bus
MINI-PCI BUS CONNECTOR PIN ASSIGNMENT
You will find a Mini-PCI connector in our PMB-472.
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
ASSIGNMENT
NC
NC
NC
NC
NC
NC
NC
NC
PIRQJF
VCC3_3
NC
GND
PPCLK
GND
PREQJ3
VCC3_3
AD31
AD29
GND
AD27
AD25
NC
C_BEJ3
AD23
GND
AD21
AD19
GND
AD17
C_BEJ2
IRDYJ
VCC3_3
NC
SERRJ
GND
PMB-472 USER′S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
ASSIGNMENT
NC
NC
NC
NC
NC
NC
NC
NC
VCC
PIRQJE
NC
NC
PCI_RSTJ
VCC3_3
PGNTJ3
GND
NC
NC
AD30
VCC3_3
AD28
AD26
AD24
IDSEL
GND
AD22
AD20
PAR
AD18
AD16
GND
FRAMEJ
TRDYJ
STOPJ
VCC3_3
Page: A-3
Appendix
A
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
Page: A-4
Expansion Bus
PERRJ
C_BEJ1
AD14
GND
AD12
AD10
GND
AD8
AD7
VCC3_3
AD5
NC
AD3
VCC
AD1
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
DEVSELJ
GND
AD15
AD13
AD11
GND
AD9
C_BEJ0
VCC3_3
AD6
AD4
AD2
AD0
NC
NC
GND
NC
NC
NC
NC
NC
GND
NC
NC
NC
NC
NC
PMB-472USER′S MANUAL
Appendix
A
Expansion Bus
COMPACT FLASH CARD CONNECTOR PIN ASSIGNMENT
The pin assignments of Compact Flash Card connector are stated below.
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ASSIGNMENT
GND
D03
D04
D05
D06
D07
-CS0
A102
-ATASEL
A092
A082
A072
VCC
A062
A052
A042
A032
A02
A01
A00
D00
D01
D02
-IOCS16
-CD2
PMB-472 USER′S MANUAL
PIN
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Assignment
-CD1
D111
D121
D131
D141
D151
-CS11
-VS1
-IORD
-IOWR
-WE3
INTRQ
VCC
-CSEL
-VS2
-RESET
IORDY
-INPACK
-REG3
-DASP
-PDIAG
D081
D091
D101
GND
Page: A-5
APPENDIX
TECHNICAL
SUMMARY
B
This section introduce you the maps concisely.
Section includes:
z Block Diagram
z Interrupt Map
z RTC & CMOS RAM Map
z Timer & DMA Channels Map
z I / O & Memory Map
Page: B-1
Appendix
B
Technical Summary
BLOCK DIAGRAM
Page: B-2
PMB-472 USER′S MANUAL
Appendix
B
Technical Summary
INTERRUPT MAP
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
System TIMER
Keyboard
Cascade
Serial port 2
Serial port 1
Available
Floppy
Parallel port 1
RTC clock
Available
Available
Available
PS/2 Mouse
Math coprocessor
IDE1
IDE2
PMB-472 USER′S MANUAL
Page: B-3
Appendix
B
Technical Summary
RTC & CMOS RAM MAP
CODE
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
30
31
32
33
34-3F
40-7f
Page: B-4
ASSIGNMENT
Seconds
Second alarm
Minutes
Minutes alarm
Hours
Hours alarm
Day of week
Day of month
Month
Year
Status register A
Status register B
Status register C
Status register D
Diagnostic status byte
Shutdown byte
Floppy Disk drive type byte
Reserve
Hard Disk type byte
Reserve
Equipment byte
Base memory low byte
Base memory high byte
Extension memory low byte
Extension memory high byte
Reserved for extension memory low byte
Reserved for extension memory high byte
Date Century byte
Information Flag
Reserve
Reserved for Chipset Setting Data
PMB-472 USER′S MANUAL
Appendix
B
Technical Summary
TIMER & DMA CHANNELS MAP
Timer Channel Map :
Timer Channel
0
1
2
Assignment
System timer interrupt
DRAM Refresh request
Speaker tone generator
DMA Channel Map :
DMA Channel
0
1
2
3
4
5
6
7
Assignment
Available
Available
Floppy
Available
Cascade
Available
Available
Available
PMB-472 USER′S MANUAL
Page: B-5
Appendix
B
Technical Summary
I/O & MEMORY MAP
Memory Map :
MEMORY MAP
0000000-009FFFF
00A0000-00BFFFF
00C0000-00DFFFF
00E0000-00EFFFF
00F0000-00FFFFF
0100000-FFFFFFF
ASSIGNMENT
System memory used by DOS and
application
Display buffer memory for VGA/ EGA /
CGA / MONOCHROME adapter
Reserved for I/O device BIOS ROM or
RAM buffer.
Reserved for PCI device ROM
System BIOS ROM
System extension memory
I/O Map :
I/O MAP
000-01F
020-021
022-023
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0-0FF
1F0-1F8
278-27F
2B0-2DF
2F8-2FF
360-36F
378-37F
3B0-3BF
3C0-3CF
3D0-3DF
3F0-3F7
3F8-3FF
Page: B-6
ASSIGNMENT
DMA controller (Master)
Interrupt controller (Master)
Chipset controller registers I/O ports.
Timer control regsiters.
Keyboard interface controller (8042)
RTC ports & CMOS I/O ports
DMA register
Interrupt controller (Slave)
DMA controller (Slave)
Math coprocessor
Hard Disk controller
Parallel port-2
Graphics adapter controller
Serial port-2
Net work ports
Parallel port-1
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy disk controller
Serial port-1
PMB-472 USER′S MANUAL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement