ERNITEC DigiOpG2 EDNS3000 Series Installation, Programming, & User Manual

Add to my manuals
51 Pages

advertisement

ERNITEC DigiOpG2 EDNS3000 Series Installation, Programming, & User Manual | Manualzz

Digital Video Recorder

Series EDNS3000

16 camera system

Installation,

Programming,

& User Manual

DigiOpG2 Digital Video Recorder Page 1

3040-00052

DigiOpG2 Digital Video Recorder

WARNING

TO REDUCE FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THE UNIT TO RAIN OR MOISTURE.

Page 2

This installation should be made by a qualified service person and should conform to all local codes.

3040-00052

DigiOpG2 Digital Video Recorder

Cautions

Read Before System Operation

Follow these details to prevent material damage or personal injury.

Signs of Caution and Warning

Warning: This sign indicates that the user could be seriously wounded or expect property damage if not

used or installed properly.

Important Safeguards

Warning

1. Use the power cord, which is supplied or recommended by the supplier.

2. Do not dismantle or assemble the product.

It may cause malfunction or fire.

3. Do not touch the product with wet hands.

It may cause malfunction or fire.

4. Matters must be ensured to a professional product installation.

Delinquent installation may be the reason for malfunction, electric shock or fire.

5. Ground connection must be done. If grounding is not done, it may cause malfunction or electric shock.

6. Ground connection must not touch gas pipe, water pipe or telephone line.

7. Prevent metallic foreign substance from going inside the product.

It may cause malfunction or electric shock.

8. Do not spray insecticide or flammable spray while equipment is switch on.

It may cause fire.

9. Prevent water from entering inside electrical parts.

10. Do not drop, give strong vibration, or shock to the product.

It may cause malfunction.

11. The air inhaler of the front panel and air outlet of the back panel must not be blocked during installation or the internal temperature of the product could be greater than allowable and cause malfunction or fire.

12. Do not touch the product or the power cord when there is thunder.

It may cause electric shock.

13. Do not install the product near or on top of heating source.

The internal temperature of the product could be greater than allowable and cause malfunction or fire.

14. Do not install the product on inclined or unstable location or where vibration could be committed.

It may cause malfunction.

15. Do not touch the power cord with wet hands.

It may cause electric shock.

16. Hold the body of the plug while removing the power plug.

Do not pull the power cord. Damage to the power cord may generate heat or cause fire.

17. Remove power cord from outlet when product is not used for a long time.

It may cause a short-circuit or electric shock.

18. Do not turn off the power by removal of the power plug.

To turn off the power, click the power button from the front panel.

When the system stops abnormally, the power button might not work. Click power button for 5 full seconds to turn power off.

19. Do not cut off the power artificially, or give shock or vibration to unit while the hard disk is activating.

It may cause hard disk failure or loss of data.

3040-00052

Page 3

DigiOpG2 Digital Video Recorder

CATEGORIES

CAUTIONS..............................................................................................................................................................................3

READ BEFORE SYSTEM OPERATION ....................................................................................................................................3

1.

SYSTEM STRUCTURE AND INSTALLATION ................................................................................................................5

2.

1.1

Getting Started ........................................................................................................................................................... 5

EXPLANATIONS FOR EACH FUNCTION......................................................................................................................6

3.

2.1

Front Panel ................................................................................................................................................................. 6

2.2

IR Remote Controller................................................................................................................................................... 9

2.3

Rear Panel................................................................................................................................................................. 10

INSTALLATION ..........................................................................................................................................................14

3.1

Connecting Peripheral Devices .................................................................................................................................. 14

3.2

System Startup and Shutdown .................................................................................................................................. 15

4.

OPERATION...............................................................................................................................................................16

4.1

Log-in ....................................................................................................................................................................... 16

4.2

Real time Live Mode.................................................................................................................................................. 17

4.3

Recorded Image Playback Mode................................................................................................................................ 21

5.

6.

IMAGE BACKUP ........................................................................................................................................................23

5.1

CD Backup................................................................................................................................................................ 23

5.2

USB External Storage Device for Backup.................................................................................................................... 26

SETTINGS ..................................................................................................................................................................28

6.1

System-General......................................................................................................................................................... 29

6.2

System-Date and Time .............................................................................................................................................. 32

6.3

System-Network ....................................................................................................................................................... 34

6.4

System-Passwords..................................................................................................................................................... 35

6.5

Camera-Recording .................................................................................................................................................... 36

6.6

Camera-Title & Schedule........................................................................................................................................... 38

6.7

Camera-Color ........................................................................................................................................................... 39

6.8

Camera-Audio & P/T/Z .............................................................................................................................................. 40

6.9

Alarm-Input .............................................................................................................................................................. 41

6.10 Alarm-Output ........................................................................................................................................................... 43

6.11 Tools-System Information .......................................................................................................................................... 44

6.12 Tools-System Upgrade............................................................................................................................................... 45

6.13 Tools-System Default................................................................................................................................................. 46

6.14 Quit .......................................................................................................................................................................... 47

7.

APPENDIX .................................................................................................................................................................48

7.1

Sensitivity Setting...................................................................................................................................................... 48

7.2

System Specifications ................................................................................................................................................ 50

Page 4

3040-00052

DigiOpG2 Digital Video Recorder

1.

SYSTEM STRUCTURE AND INSTALLATION

1.1

Getting Started

The following accessories are supplied with the EDNS-3000 series digital video recorder. If any of these items is missing or damaged, notify your dealer immediately. Keep the packing utilities for moving or storage purposes afterwards.

Page 5

EDNS-3000

1

2

1

1

Qty

1

1

1

Accessories

User Manual

IR Remote Controller

DigiOp RemoteAgent CD

Power Cable

Power Battery (AAA Size)

Rubber Mount Set

Rack Mounts and Screws

3040-00052

DigiOpG2 Digital Video Recorder

2.

Explanations for each function

2.1

Front Panel

The buttons on both the front panel of the EDNS-3000 and IR Remote Controller have the same functions. Each button can activate different functions. The buttons on the front panel of EDNS-3000 may be different in shape than the remote controller buttons, but the IR Remote Controller can also control the functions controlled by the front panel of the EDNS-

3000.

Page 6

No.

1

2

3

4

5

6

Buttons

Power Button

Power LED

HDD LED

Network LED

Sensor LED

Audio LED

7

SCR MODE

CH1-8/CH9-16

8

9

Multiple Screen Mode

Buttons (Arrow

Buttons)

PAN/TILT/

ZOOM/FOCUS/ IRIS

10 SETUP

11 SEARCH

12 Jog/Shuttle

13 USB Port

14 BACKUP Button

15 EVENT Button

16 RETURN Button

17 OSD Button

18 P/T/Z Button

19 SEQ Button

20 ENTER Button

21

Fast Playback

Backwards

22

Playback Backward

Frame by Frame

23 Playback

24

Playback Forward

Frame by Frame

25 Fast Playback Forward

Functions

Use to turn the Power On/Off.

Shows Power On/Off status of the system (GREEN: Working, RED: Stand-by).

Shows if the camera image is being stored into or retrieved from the HDD (Hard Disk

Drive).

LED is lit while the network client(s) (RemoteAgent) is connected to the system.

LED is lit when alarm sensor is activated.

LED is lit while audio data from audio input device is being recorded.

Button to select modes of the arrow buttons.

Whenever the button is pressed, the screen will change to

[1~8 channel mode], [9~16channel mode], or [multiple(split) screen mode].

The default mode is [multiple(split) screen mode].

Buttons to select the multiple screen mode as printed, or for use as cursor keys.

Button for Camera PAN/TILT/ZOOM/FOCUS/IRIS functions.

Menu to set user environment of the system.

Search recorded image.

Jog (inner dial): playback frame by frame.

Shuttle (outer dial): Speed up the playback speed of the image (1~32X).

USB interface port to connect external storage equipment.

Button to backup recorded image data.

Shows system’s event information in order of time and brings up event viewer to search image of the corresponding time.

Use to exit from the setting menu or to cancel setting value.

Button to control the OSD (On-Screen Display).

For using P/T/Z functions of the camera.

Automatic time sequencing for monitor images.

Use to enter detail menu, go into the next stage, select or set value.

Fast playback the recorded images backwards in the playback mode.

Playback the recorded images frame by frame backwards in the playback mode

(playback only I-Frame)

Playback recorded images from playback menu.

Playback the recorded images frame-by-frame forward in the playback mode.

Fast playback the recorded images forward in the playback mode.

3040-00052

DigiOpG2 Digital Video Recorder

2.1.1.

Power Button

When the power cable of the product is connected, press this button to turn power on or off.

2.1.2.

Power LED

LED to show the power input and status of the system. The LED is red when the system is in stand-by position, but is green when the system is working and power is being supplied.

2.1.3.

HDD LED

LED is blue when the camera image is being stored into or retrieved from the HDD. So, even though the system is continuously recording, the HDD LED is only lit when actual data is recorded in the HDD. Usually, the LED will be flickering, and this is normal.

2.1.4.

Network LED

LED is blue when the system is connected to any network client (RemoteAgent). Light is automatically out when all clients are disconnected.

2.1.5.

Sensor LED

LED is lit when the system has any activated sensor input.

2.1.6.

Audio LED

LED is lit when audio data from audio input device is being recorded. Even though the audio input device is properly connected, it will not light up when audio is not recorded.

2.1.7.

SCR MODE or CH1-8 / CH9-16

Use to see the images on the monitor as multiple screens. Whenever this button is pressed, [1-8] ( ) group icon, [9-16] group icon ( ), or no icon will be seen on the lower right end of the monitor. When ( arrow button will be used to select no. 1~8 images. Thus, when icon (

) is indicated on the screen, the

) appears on the screen, the arrow button will be used to select images from no. 9~16. If the icon is not indicated, the arrow button will be use to select multiple screens (

As a default mode, arrow button will be used to select multiple screens.

).

Note

In case of IR Remote Controller, direction (number) key will be used to input channel no. 1~16. If necessary, select split screen mode by pressing [SCR MODE] button on the IR Remote Controller.

2.1.8.

Select Multiple Screen (Arrow Button)

Select each arrow button and the corresponding multiple screens will appear. Up, down, left, right arrow buttons are used to move the cursor to “Setting” mode and are also used to increase/decrease the setting value. Furthermore, they are used to operate camera PAN/TILT Movement, ZOOM IN/OUT, FOCUS FAR/NEAR.

Page 7

3040-00052

DigiOpG2 Digital Video Recorder

2.1.9.

PAN/TILT/ZOOM/ FOCUS/IRIS

Press this button to control PAN/TILT/ZOOM/FOCUS/IRIS value in sequence. This is when PTZ driver has been installed in the camera.

2.1.10.

SETUP

Set the environment of the EDNS-3000 series according to the user requirement.

2.1.11.

SEARCH

Search the recorded image by date and time. Refer to “Recording Image Playback Mode” for detail image searching method.

2.1.12.

Jog / Shuttle

Jog / Shuttle dial is used to playback recording images. The inner dial is called Jog and the outer dial is called Shuttle. The

Jog/Shuttle dial has two kinds of functions. The Jog is used to find the recording image frame by frame. Turn the Jog dial clockwise or anti-clockwise (only I-Frame is playback during anti-clockwise) to see the image frame by frame during pause state. The Shuttle is used to speed up the playback speed of images by clockwise or anti-clockwise. Playback speed is indicated as x2, x4, x8, x16, x32 on the lower end of the screen.

2.1.13.

USB Port

Use to backup recorded images of the EDNS-3000 series by using USB storage device. System software upgrade is possible with USB storage device.

Note

Refer to “Image Backup” for detailed explanation of USB storage devices supported by EDNS-3000 series.

2.1.14.

BACKUP Button

Use to back up images recorded in the HDD to a supported storage device. When this button is pressed, the information from the backup device connected to EDNS-3000 series (ex. CD-RW drive) will be indicated on the screen.

Refer to “Image Backup” for detailed information about backup.

2.1.15.

EVENT Button

Shows system setting changes, alarms, etc., by the order of time and brings up event viewer to search image of the corresponding time. Refer to “Event Search” for further details.

.

2.1.16.

RETURN Button

Use to cancel the password just typed at the setting menu or to return to previous menu.

2.1.17.

OSD Button

OSD will initially be displayed on the screen. When the [OSD] button is clicked once, the OSD will disappear. Click [OSD] button again and the text will reappear.

2.1.18.

P/T/Z Button

Click [P/T/Z] button and an icon will appear on the lower right end of the screen image to show P/T/Z status. This is when

P/T/Z driver has been installed.

2.1.19.

SEQ Button

Press [SEQ] button and screen will automatically change. Refer to “Settings” for automatic sequencing interval (does not work on 16 split screen mode).

2.1.20.

ENTER Button

The [Enter] button is used to go into the next stage, select value, or setting.

Page 8

3040-00052

DigiOpG2 Digital Video Recorder

2.2

IR Remote Controller

The function buttons of the IR Remote Controller are the same as function buttons on the front panel as shown below.

No.

Functions

Power Button

Activating LED

F2 (Reserve Button)

F1 (Reserve Button)

IRIS+ (Open Iris)

IRIS– (Close Iris)

ZOOM IN (Narrow)

FOCUS FAR

FOCUS NEAR

ZOOM OUT (wide)

ENTER

SETUP 12

RETURN 13

Select Number Button /

Multiple Screen

SCR / CH Button

F/O/E Button

SEARCH Button

16

17

14

15

BACKUP Button

EVENT Button

3040-00052

18

19

10

11

8

9

6

7

4

5

1

2

3

Page 9

DigiOpG2 Digital Video Recorder

Fast Playback Backwards Button

Playback Button

Fast Playback Forward Button

Playback Backward Frame by

Frame

Pause Button

Playback Forward Frame by Frame

23

24

25

20

21

22

OSD Button

P/T/Z Button

SEQ Button

26

27

28

Note Button #16: F/O/E Button (use only on remote controller)

The object in the recorded image might show the feathering effect during frame playback because images at

720x480(PAL:720×576) resolution have higher vertical resolution than 640x240(PAL:640×288) or 352×240

(PAL:352×288). The feathering of the image can be solved when only one of two Fields (Odd, Even Field) is selected. Default is frame playback. When the button is pressed, it will change to Odd Field Playback-> Even Field

Playback-> Frame Playback order.

Note

To use the IR Remote Controller, synchronize front panel button and IR remote controller by inputting the initial ID.

The user requires setting the ID only once. Refer to “Settings” for detailed information about ID input.

Note

When the IR Remote Controller is used to change the channel, no. 1 button is also used to select channels after number 10. Press no. 1 button and it will be ready to add another extra number. Example, press no. 1 and once it is ready to add another no., press 2. Then, channel will change to channel no. 12. But press no. 1 button for few seconds and the channel will go to no. 1 channel.

2.3

Rear Panel

The following is the rear panel of the EDNS-3000 series system. The picture below is EDNS3000-16EP model.

Note

The configuration differs according to the model.

Page 10

3040-00052

DigiOpG2 Digital Video Recorder

No.

1

2

3

7

8

9

4

5

6

Camera Input (BNC)

LOOP OUT

MON OUT

Name

SPOT OUT

Power Input

Select NTSC / PAL

SENSOR Input

USB Port

LAN Port

10 S-Video Output

11 Serial Port

12 Audio Out

13 Audio In

14 Alarm Out / P/T/Z

Functions

Connect to Camera (supports NTSC/PAL)

Camera images of each channel will be outputted as is (also used when the corresponding image is required for other product)

Connect to the main monitor for camera image surveillance/management/playback

Use to output the entire surveillance screen one by one, in an interval

Connect main power cable

Select the signal system (NTSC/PAL)

Connect 16 external input sensors (supports N/O or N/C)

Connect USB device

RJ-45 socket for 10/100 Ethernet connection

Secondary main monitor output

RS-232C port

Connect Audio Output Device (with Amp.)

Connect Audio Input Device (with Amp.)

Connect P/T/Z receiver(RS-485) and/or relays

Note

Ensure that the specification for the EDNS-3000 agrees with the specification for the peripheral devices. For details about adding additional peripheral devices, consult your dealer.

Page 11

3040-00052

DigiOpG2 Digital Video Recorder

2.3.1.

Camera

Connect BNC plug of camera video cable into the desired BNC input.

Note

Camera input voltage level is 1Vp-p±10%.

2.3.2.

LOOP OUT

Use to apply the video of camera input to other device. Without using a video distributor, the same image can be connected to the camera input of other product.

2.3.3.

MON OUT

Connect the BNC cable of the monitor to MON OUT BNC cable of the rear panel.

2.3.4.

SPOT OUT

The spot monitor can only be used to display input images in automatic interval mode. Refer to “Settings” for automatic interval time setting of spot monitor.

2.3.5.

Power Input

Connect to main power cord of the system.

Caution

Before plugging-in the power cord to the system, check if the power is in accordance with the system specification (Single Phase AC 115~230V)

2.3.6.

Select NTSC / PAL

Turn off the power of the EDNS-3000 series and select the NTSC/PAL switch correctly. Then turn on the power again.

2.3.7.

SENSOR Input

Connect sensor (dry contact type). Separate the terminal block and wire all devices to desired pins, before connecting the terminal block again. Connect each ground (GND) line to “G” pins.

Note

Support both N/O (Normal Open) and N/C (Normal Close). If connected sensor is not functioning, ensure wiring is correct.

2.3.8.

USB Port

Connect USB storage device.

Note

Refer to “Image Backup” for details on the supported USB storage device of EDNS-3000.

2.3.9.

LAN Port

Connect RJ-45 jack of LAN cable to LAN port. Network has to be TCP/IP base 10/100BASE-TX Ethernet LAN (Local Area

Network), Internet or exclusive line, and IP address should be fixed one. Consult network administrator for proper network configuration.

2.3.10.

S-Video Output

One additional main monitor can be installed by using the S-Video output. Use the S-Video cable to connect the EDNS-3000 with the monitor, which has S-Video Input.

2.3.11.

Serial Port

Port for RS-232 signal output.

2.3.12.

Audio Out

Connect audio output equipment.

Note

Use of audio output device with an amplifier is recommended

2.3.13.

Audio In

Connect Audio Input device.

Note

Input voltage of audio input device is line level.

Use of audio output device with amplifier is recommended.

2.3.14.

Alarm Out / P/T/Z

Connect various alarm devices controlled by relay output. EDNS-3000 series supports RS-485 for P/T/Z control.

3040-00052

Page 12

DigiOpG2 Digital Video Recorder

Note

Refer to the following picture to control P/T/Z controller. General wiring of P/T/Z controllers is as follows. However, the wiring of different P/T/Z controller may differ. Be cautious that the P/T/Z controller will not function properly when wiring is incorrect.

Page 13

EDNS-3000

Consult your dealer to use other than RS-485.

3040-00052

DigiOpG2 Digital Video Recorder

3.

Installation

3.1

Connecting Peripheral Devices

This section describes how to efficiently hook up peripheral devices for usage with the EDNS-3000 series.

Install the EDNS-3000 series on flat surface. If required, attach the rubber mount for installation. If 19-inch rack is used, it is recommend to install the system on shelve and use 2.5~3U (1U=1.75 inch or 4.45cm) space for proper ventilation.

Note

Install system in location with good ventilation to prevent overheating.

Page 14

Caution

Depending on the grounding, the coaxial cable connecting to the camera has danger of electric shock. Shut down power of the system completely (unplug the power cable) before connecting video cable to BNC port.

3040-00052

DigiOpG2 Digital Video Recorder

3.2

System Startup and Shutdown

3.2.1.

System Startup

After connecting all peripheral devices, connect power cord to EDNS-3000 series for system startup. The power will be turned on automatically within 5 seconds of power cord being connected. However, power will not be turned on automatically, if power button was previously turned off by user. In that case, the power button must be pressed again to restore power.

3.2.2.

System Shutdown

To turn off the power, press the power button for proper shutdown of the system. Do not turn off the power by pulling the power plug.

CAUTION

In case the power plug is pulled off while the system is operating, the currently recording file may not be closed properly. In addition, even though Journaling File System is not damaged, index information required for quick file search may not be saved. Of course, Auto Recovery System will recover these files during the next booting. This process might take between a few seconds to a few minutes. Therefore, turn off system power by pressing the power button to prevent malfunction.

3.2.3.

Countermeasures after abnormal shutdown

EDNS-3000 series has been designed to operate for long periods without a problem.

The operation of the system can be locked, when major parts (such as hard disk) function abnormally due to external electric shock, physical damage, or other various reasons.

The system stops operating during abnormal situations, and the internal watchdog circuit is activated in order to reset the system for rebooting within 2 minutes. The system will then recover normally. It will also automatically reboot even when there is power failure. However, if major parts (such as hard disk) are physically damaged, it is impossible to recover normally.

This will cause continuous rebooting by watchdog or deadlock without reset.

Countermeasures for abnormal discontinuation are as follows.

1.

In case the power cannot be turned off, turn off by pulling the power cord.

2.

Wait for about 10 seconds and reconnect the power. Ensure the system is functioning properly.

3.

Consult your dealer if system is not functioning properly after reconnecting power.

3.2.4.

Automatic file testing and recovery

By using Auto-Scan and Auto-Recovery, the files damaged due to abnormal shutdown will be recovered automatically.

Note

Generally, when all files in the hard disk have been closed properly during normal shutdown, it will take only a few seconds to examine the files after rebooting. It will take few minutes or more to recover the files if recovery is required, however.

Page 15

3040-00052

DigiOpG2 Digital Video Recorder

4.

Operation

4.1

Log-in

Check the power connection. The system can be used after power-on.

EDNS-3000 series has various setting categories. The administrator can set the system password and <User> to prevent unauthorized changes to setting values and alteration to recorded file.

Below is first login box indicated on the screen after electric power is on. Refer to “System-Password” for how to set and change <User> password.

Page 16

Only <Administrator> can enter the setting menu (<User> cannot).

Before entering the setting menu, <Administrator> password must be entered in the box as displayed below. Refer to

“System-Password” for how to set and change <Administrator> password.

Note

Be cautious not to forget the Administrator password. If it is forgotten, consult your dealer.

3040-00052

DigiOpG2 Digital Video Recorder

4.2

Real time Live Mode

Real time live image can be seen after power up.

Note

Both the IR Remote Controller and the front panel button can be used in EDNS-3000 series.

4.2.1.

Screen configuration

1

Page 17

2

Above is the typical real time mode screen. Press [OSD] button on the front panel or IR Remote Controller to control the display of OSD. Whenever the button is pressed, the display of OSD will toggle between appearance and disappearance.

The following is the explanation of each item displayed on the screen from single screen to 16 split screen.

1.

Channel Name: Shows camera title of the channel. Refer to “Setting-> Camera -Title” for how to set and change camera title.

2.

Date and Time: Indicates present date and time of the system. When the recorded data is playback, indicated date and time will be those of the recorded image currently displayed.

3040-00052

DigiOpG2 Digital Video Recorder

4.2.2.

Single screen mode

To see an individual screen, press the [SCR MODE] button on the front panel or IR Remote Controller. Single screen mode must be selected to hear sound from the audio device that is connected to the system, or to see the recorded image.

Press the arrow button on the front panel to change channels.

Note

If split screen mode is selected when an arrow key is pressed, press the [SCR MODE] button.

Press the number button in the IR Remote Controller and the corresponding channel image can be seen. For example, the following image is seen when number 2 is pressed.

Page 18

Note

Check connection status of the camera BNC cable or monitor output cable on the rear panel when image of the monitor cannot be seen.

3040-00052

DigiOpG2 Digital Video Recorder

4.2.3.

Split Screen Mode

In the EDNS-3000 series, the user can see several camera images in various multiple screen formats. Press each button and the corresponding images will be seen in split screen mode.

Note

To see split screens, press the [SCR Mode] on the front panel or IR Remote Controller.

To see the camera image in various split modes, press corresponding arrow buttons. The pictures below correspond to the buttons on the front panel and IR Remote Controller.

Page 19

Button

Front Panel Arrow Button

Multiple Screen Button

IR Remote Controller Number Button

Multiple Screen

1 Screen 4 Screens

6 Screens

9 Screens

13

Screens

8 Screens

10

Screens

16

Screens

3040-00052

DigiOpG2 Digital Video Recorder

4.2.4.

See Operating Status

In real time live mode, icons or messages will be indicated on the screen to notify the system mode or status.

Below are the icon categories, which are indicated on the monitor.

Fast Backward Playback

Playback Backward Frame by

Frame

Pause

Playback

Fast Forward Playback

Playback Forward Frame by

Frame

Alarm

Direction Key

Select Images from No. 1~8

Channels

Select Images from No. 9~16

Channels.

Split screens

Zoom (In/Out)

Focus

Iris

Automatic Screen

Sequence

P/T/Z Controller Activates

Note

When an alarm occurs in the connected channel, the [Alarm] icon will appear on the right bottom side of the screen and “Channel Name” will be indicated in red. The alarm icon will disappear, but the channel number will remain in red for a while when the user enters setup menu, or tries to backup during alarm.

The number buttons on the IR Remote Controller can be used as direction keys.

While [Direction Key] icon is being displayed, the number keys on IR Remote Controller can be used as arrow keys.

When IR Remote Controller is used for P/T/Z control, press [P/T/Z] button to display [P/T/Z] icon and, then, press

[SCR/CH] button to display [Direction Key] icon.

Page 20

3040-00052

DigiOpG2 Digital Video Recorder

4.3

Recorded Image Playback Mode

The user can select date and time to search for a certain file within the recorded image of the EDNS-3000 series.

4.3.1.

Recording Image Playback

To playback recorded image, press (@) button on the front panel or IR Remote Controller. Press the playback button and the latest recorded image will be playback.

Use the Jog /Shuttle on the front panel to playback recorded file easily.

Turn the Jog and the recorded file can be playback frame by frame backward and forward.

Turn the Shuttle and recorded image speed can be increased by 2, 4, 8, 16 or 32 times backward and forward.

4.3.2.

Search Date/Time

The User can search date and time to playback recorded image.

Press [Search] button on the front panel or IR Remote Controller and the following screen, showing calendar and time graph, will appear.

Page 21

Following the sequence below to search date and time:

1.

Select the date with recorded image by clicking the calendar with the arrow button. The date with recorded image will be indicated in white.

2.

Move the green arrow to date required before pressing the [Enter] button on the front panel or IR Remote

Controller.

3.

Next, move the green arrow (located on the time graph below the calendar) to the desired time.

4.

One hour is divided into 15 minutes increments. Move the green arrow to the desired time.

5.

Upon moving the green arrow, click the [Enter] button. The image for the corresponding time will be shown in pause state.

6.

Press the [Play] button to playback the recording image or use the Jog/ Shuttle to search the exact time.

3040-00052

DigiOpG2 Digital Video Recorder

4.3.3.

Event Search

EDNS-3000 series uses the Event Log to document important events such as sensor activity, system On/Off, changes in settings. The Event search function is used conveniently to find an image corresponding to a particular event.

Note

In order to leave and search alarm history on the Event Log, turn on the [Alarm In] function on the setting menu.

Refer to “Setting->Alarm Input” for detailed instructions.

To check the event history, press the [Event] button on the front panel or IR Remote Controller. Press the button and the following Event Viewer will appear.

Page 22

Occurred date, time (hr: min: sec), (S: Standard D: DST) and signaled alarm will be indicated on the Event Viewer screen. Use the arrow button on the front panel or the IR Remote Controller to move to the recorded image corresponding with a particular event. The up and down arrow buttons are used to move the selection bar up and down. The left and right buttons are used to move page by page.

The following is the category as indicated on the Event Viewer.

1.

Alarm in Signal (for each channel) - Alarm is signaled on sensor [1] (Alarm (Sensor) Number)

2.

Enter P/T/Z Mode (for each channel) -Start P/T/Z on CH2 (Channel Number)

3.

Setup Menu Setting - Changed system settings

4.

System Start (Power on), Shutdown (Power off) - Starting system, Shutdown system

5.

System Upgrade - Upgraded to 1.0.4 (version)

6.

Change Resolution (Recording Image Size) - Image Size is changed to 640x288 (Resolution)

7.

Change Date and Time - Date or time is changed

8.

Log on Information or Authority (Connect by User or Admin) - Logged on with <User (or Admin)> privilege

9.

Change Network address - Network address is changed

10.

Go to Factory Default - Reset System Settings

11.

Log off Information - <User> had been logged off

Press [Enter] or [Play] button on the front panel or IR Remote Controller after selecting date and time to see recorded image for the time chosen. If there is no recorded image for the corresponding time, the image of the closest time will be playback.

Note

When the alarm does not activate and the alarm input is set properly, check the alarm wiring on the rear panel.

Then, check whether the sensor input status is functioning properly.

3040-00052

DigiOpG2 Digital Video Recorder

5.

Image Backup

There are two ways to backup the recorded images of EDNS-3000 series. The first is by using internal CD-RW drive (option).

The second is by using USB external storage device.

5.1

CD Backup

Use the CD-RW attached to the EDNS-3000 series to backup the recorded images.

Press the [Backup] button on the front panel or IR Remote Controller and the following screen will appear.

Note

The specifications will show differently, depending on the model of CD-RW drive. Refer to the CD-RW drive manual for a detailed explanation.

Page 23

When the CD-RW drive is not installed or not properly connected, the following error message will appear. The following error message will also appear if CD-R media (Blank CD) for storage is not on the CD tray.

Note

Consult your vendor if you require detailed information on the CD-RW.

3040-00052

DigiOpG2 Digital Video Recorder

Enter each item on the screen below to backup recorded images.

1.

Select the recording start time for backup.

2.

Also, select the recording end time for backup.

3.

Select channels to backup. The user can select several channels together, but if the backup data capacity is more than the storage capacity, backup will not proceed. Select the channel by using the cursor and pressing [Enter] button.

4.

After selecting all the items, press [Next] button to proceed to the next screen.

Page 24

Note

Input the time by pressing the arrow (up, down, left, right) button of the front panel on the IR Remote Controller.

When the channels are not selected, error message will appear as shown below.

3040-00052

DigiOpG2 Digital Video Recorder

Press [Enter] after correctly selecting all the items correctly for backup. Proceed as indicated below.

Page 25

The following is the list of media supported in the internal CD-RW of EDNS-3000 series.

CD-R :

Acer, AMT, CMC, Kodak, LeadData, Maxell, Mitsubishi Chemical, Mitsui, Nan Ya, Philips, Princo, Prodisc, Ricoh,

Ritek, Sony, Taiyo Yuden, TDK, Verbatim, Yamaha

CD-RW :

Acer, AMT, CMC, Digimaster, Maxell, MaxMax, Melody, Mitsubishi Chemical, Philips, Plextor, Prodisc, Ricoh, Ritek,

Sony, TDK, Traxdata, Verbatim, Yamaha

When the backup is completed, the following message will appear.

3040-00052

DigiOpG2 Digital Video Recorder

5.2

USB External Storage Device for Backup

EDNS-3000 series supports USB. Connect external storage device to the USB port on the front or back panel.

Click [BACKUP] button on the front panel and the screen below will appear.

Page 26

Note

Below is a lists of USB external storage devices supported by the EDNS-3000 series. Consult your vendor if the devices do not operate properly.

1. AOpen CRW5224 External CD-RW Drive

2. AOpen EHW-4048U External CD-RW Drive

3. SONY CRX2100U External CD-RW Drive

4. Plextor PX-W4012TU External CD-RW Drive

5. DVICO MOMOBAY CX-2 2.5" External HDD

6. UNiCORN Portable HDD HD-250 External HDD

7. OTI FELLOW Flash Disk Drive

8. Hanbit STORiUM N Flash Disk Drive

EDNS-3000 series does not support DVD±RW drive. Should use of DVD±RW drive be required, use CD-R media versus DVD+RW or DVD-RW.

The following error message will appear if the USB storage fails to backup.

3040-00052

DigiOpG2 Digital Video Recorder

When the USB storage device is connected incorrectly, the following message will appear.

If there is not enough free disk space in the USB storage device, the following error message will appear.

The following message will appear when the image backup of the USB storage device has been completed.

Note

To use USB storage for backup, use FAT file system. If the storage device is set to NTFS file system, backup will fail.

Note

DO NOT connect two or more external USB storage devices to the system. If not, the system may not recognize those devices correctly. In addition, some USB hubs cannot be recognized correctly.

Page 27

3040-00052

DigiOpG2 Digital Video Recorder

6.

Settings

To operate EDNS-3000 series, appropriate setting values in the setting menu are necessary. Users can either input or change the setting values listed in the table below.

Main

Classification

Sub Classification

System

Camera

Alarm

Tools

Quit

General

Date and Time

Networks

Passwords

Recording

Title & Schedule

Color

Audio & P/T/Z

Alarm Input

Alarm Output

System Information

System Upgrade

System Default

Log Off

Close Menu

Setting Category

Title

Start

End

Bright

Contrast

Color

Tint

Audio

Aud-CH

P/T/Z Address

Camera#

Start

End

Type

Relay#

Alarm Mode

Dwell

Image Size

Page Sequence

IR Remote ID

P/T/Z Protocol

Spot-Out Dwell

Date and Time

Date Format

Time Format

Daylight Saving

LAN

Modem

Admin

User

Network

Record

Frame

Quality

Sensitive

LAN

TFTP

CD-ROM

Default

PAL:640x240 (NTSC:640x288)

3

10

None

1

Year, Month, Day

24 Hours

None

1

0

Off

0

50

50

50

Off

24

N/C

Off

Duration

N/A

1234

On

PAL:6

70

70

CH#

0

24

50

Page 28

3040-00052

DigiOpG2

6.1

System-General

Set general environment of the system.

Digital Video Recorder

6.1.1.

Image Size

Select the recording resolution. Resolution is the number of pixels for length and width, which are used to display one image.

Resolution displays the pixel number in (width)×(length), and the user can select one resolution among 352×240, 640×240, and 720×480. Default is 640×240.

The bigger the resolution number, the better the quality that is displayed. Resolution of 352×240 is VHS quality, and 720×480 with a high-resolution camera is DVD quality. Selecting appropriate resolution is important since higher quality images require more storage space, and shortens the recording period.

Note

Since the required storage space is proportional to the area of the image (width×length), 640×240 takes up approximately 1.8 times bigger space than 352×240, and 2.5~3 times bigger for 720×480. Therefore, the recording period decreases when selecting the high resolution.

Note

Even with the same resolution, total recording period can vary depending on characteristics such as recording quality, motion detection threshold and average motion of objects in the image, complexity of image, and video noise of the images. However, EDNS-3000 series controls the average size of images not to exceed the following maximum limit for each resolution in every occasion.

ƒ 352×240 : Normally 3~5KB, Max. Average 8KByte/image

ƒ 640×240 : Normally 5~10KB, Max. Average 13KByte/image

ƒ 720×480 : Normally 6~16KB, Max. Average 15KByte/image

If the average size exceeds the maximum, the system automatically reduces the recording quality to maintain below maximum. The issue of reduced total recording time due to increased size caused by nighttime camera noise, is therefore eliminated.

Page 29

3040-00052

DigiOpG2 Digital Video Recorder

6.1.2.

Page Sequence

Set sequencing period when automatic screen sequencing mode is selected in real time live mode. Page Sequence indicates switching over from selected screen to the next screen in fixed period of time. For example, Page Sequence is operated in 4split screen, the next screen (5-8 channel, 9-12 channel, 13-16 channel) is displayed after certain fixed period of time. This status can be on/off by pressing the [SEQ] button on the system front panel or IR remote controller. Possible setting range is

1~60 seconds, and the default is 3 seconds.

6.1.3.

IR Remote ID

Set IR remote controller ID. To operate the system easily using IR remote controller, IR remote controller ID should be set first.

The setting procedure of IR remote controller ID is shown below.

1.

Insert battery in IR remote controller. (AAA Size ×2)

2.

Press [SCR / CH] and [F/O/E] button on the IR remote controller at the same time.

3.

Check if the LED on IR remote controller is lighted.

4.

Press two-digit number (01~99) to set IR remote controller ID.

5.

Assign the identical ID number using front panel arrow keys on the system.

6.

Save the ID by pressing [Save] button on the screen.

Note

Setting the IR remote controller ID is necessary only once after purchasing the system.

Note

All systems manufactured in the factory have identical ID as initial value. Therefore, one IR remote controller can control several systems when using the initial value. To protect such circumstances, it is recommended to set different ID for each system. Since ID change on the IR remote controller is easy, it is convenient to operate several systems separately by changing the ID using one remote controller.

6.1.4.

P/T/Z Protocol

Set the protocol to control the P/T/Z controller connected to P/T/Z port on the back panel. P/T/Z controller is also called receiver or RX if it becomes separated from camera. Default is NONE, which indicates that the P/T/Z controller protocol is not set.

Protocol currently supported is shown below.

6

7

4

5

8

1

2

3

ERNITEC

Panasonic

Pelco P

Pelco D

Sensormatic

Smart Scan

VC_C4

Vicon

2400 baud rate

19200 baud rate

4800 baud rate

2400 baud rate

2400 baud rate

9600 baud rate

9600 baud rate

4800 baud rate no parity no parity no parity no parity no parity even parity no parity no parity

Set the controller address correctly for each channel after setting the protocol.

8bit

8bit

8bit

8bit

8bit

8bit

8bit

8bit

1 stop bit

1 stop bit

1 stop bit

1 stop bit

1 stop bit

1 stop bit

1 stop bit

1 stop bit

6.1.5.

Spot-Out Dwell

Set the switchover period of the Spot-Out channel to 1~60 seconds.

Page 30

3040-00052

DigiOpG2 Digital Video Recorder

6.1.6.

Save

Press the [Save] button when saving the setting value for each menu screen. Setting values won’t be saved when exiting the menu without pressing the [Save] button. Functions of [Save] buttons in each menu screen are identical.

6.1.7.

Restore

Previous values are restored to the values before the [Save] button is pressed. Press the [Restore] button to cancel the current setting values and to return to previous values. Functions of [Restore] buttons in each menu screen are identical.

6.1.8.

Cancel

Cancel the setting values in each menu screen. Functions of [Cancel] button in each menu screen are identical.

6.1.9.

Clear

Deletes the setting values inputted in each menu screen. It is used to delete the incorrectly typed password.

Functions of [Clear] buttons in each menu screen are identical.

6.1.10.

Default

Return to the initial value. Be cautious when pressing the [Default] button since all the setting values will be set to the initial value. Functions of [Default] button in each menu screen are identical.

Page 31

3040-00052

DigiOpG2 Digital Video Recorder

6.2

System-Date and Time

Set time and date of the system. Press arrow button to move the cursor to the desired position and to set correct and accurate value. Press [Save] button at the bottom of the screen to save the setting contents.

Page 32

6.2.1.

Date and Time

Input the current time and date accurately since the time and date of the system plays an important role in solving any problem with recorded image or event log.

The current time and date is stored in each recorded images with precision, and they are displayed during playback. Be cautious: Although the time and date stored in recorded images are wrong, they cannot be altered afterwards due to encryption.

Note

Users can change the time and date to the future without any problem. However, difficulty arises when changing it to the past (the same files might exist in the hard disk). Therefore, under complex recording setting, unexpected problems might arise in the system.

To solve such problems, EDNS-3000 series automatically deletes all the future files from the modified time and date. Consequently, be cautious when changing the date and time to the past. In addition, every function in the system operates normally since this procedure is handled in the background.

Note

When a long time has elapsed after a correct setting of the system time and date, the system time can go fast or slow. According to the specification of the RTC (Real Time Clock) used in EDNS-3000 series, the time difference can be 113 seconds per month in maximum. Therefore, the periodic (more than once per month) correction of the system time and date is required for the maintenance of accurate system time.

6.2.2.

Date Format

Set the date display format. Select the desired format in the date display format after pressing arrow button.

6.2.3.

Time Format

Set the time display format. Time format can be selected either by 24-hour or 12-hour base (AM or PM).

3040-00052

DigiOpG2 Digital Video Recorder

6.2.4.

Daylight Saving

Select the daylight saving time for each country. Daylight saving time setting is automatically processed when country is selected. Supported countries are displayed in the table below.

No.

9

11

13

15

17

5

7

1

3

19

21

23

25

Country

None

Austria

Brazil

Denmark

Finland

Germany

Israel

Mexico

Norway

Portugal

Spain

Switzerland

US

Representative Region

GMT

Europe/Vienna

Brazil/East

Europe/Copenhagen

Europe/Helsinki

Europe/Berlin

Israel

Mexico/General

Europe/Oslo

Portugal

Europe/Madrid

Europe/Zurich

US/Eastern

No.

10

12

14

16

18

6

8

2

4

20

22

24

Country

Australia

Belgium

Canada

Egypt

France

Greece

Italy

Holland

Poland

Russia

Sweden

UK

Representative Region

Australia/Melbourne

Europe/Brussels

Canada/Eastern

Egypt

Europe/Paris

Europe/Athens

Europe/Rome

Europe/Amsterdam

Europe/Warsaw

Moscow

Europe/Stockholm

Europe/London

Page 33

3040-00052

DigiOpG2 Digital Video Recorder

6.3

System-Network

Set the network environment of the system. An example of a LAN is shown below.

Note

Consult your vendor if user wants to use a modem.

Page 34

6.3.1.

Connection Type

Select either LAN or Modem by pressing the arrow button. Move to next item by pressing [Enter] button after selection.

6.3.2.

Host Address

Input the IP address assigned to EDNS-3000 series system.

Note

Use fixed IP for system IP.

For system IP, use the IP that is not used by other PC or DVR.

6.3.3.

Subnet Mask

Subnet Mask address recognizes the subnet to which the system belongs. Default is 255.255.255.0. Consult network administrator for accurate information.

6.3.4.

Default Gateway

This is the IP address of the network router or gateway. It is required when the user wants to connect through the external router from the remote. Default is 192.168.0.1.

Note

Consult your vendor if network connection configuration is required.

3040-00052

DigiOpG2 Digital Video Recorder

6.4

System-Passwords

Set passwords for <Admin> and <User>, and also set <Network> password to allow connections from RemoteAgent.

Set the password after selecting [Admin], [User], and [Network] by pressing arrow button.

Page 35

6.4.1.

Select

Select password to be set. Admin and user can have only one account for each.

6.4.2.

Old Password

Input the old password.

6.4.3.

New Password

Input the new password. Up to 8 digits can be inputted.

6.4.4.

Confirm

Input the new password once more for confirmation.

Note

Press [SCR MODE] button on the front panel (or [SCR/CH] button on IR remote controller), then press arrow

(up, down, left, right) button (or number buttons in IR remote controller) to input the password.

3040-00052

DigiOpG2 Digital Video Recorder

6.5

Camera-Recording

Set the general environment related to camera usage. The screen below shows the setting related to recording.

Page 36

Model

3120-16EP

3120-16EPC

3240-16EP

3240-16EPC

* FPG : Frame per Group

Max

60

60

30

30

720

×480

FPG

15

15

8/7

8/7

Max

120

120

60

60

640

×240

FPG

30

30

15

15

Max

240

120

120

120

352

×240

FPG

60

30

30

30

6.5.1.

Record

Controls whether recording of the channel will be done or not. [ON] is to record and [OFF] is not to record. If recording is not required, even when the video of the channel is feeding, set [OFF] for the channel. Then, recording of the channel stops without pulling camera BNC cable off. [ON] or [OFF] can be selected. The default is [ON].

3040-00052

DigiOpG2 Digital Video Recorder

6.5.2.

Frames

Set the desired number of recorded images per second for the connected camera. The total number of recorded images per second, per group, has an upper bound (NTSC: 30fps, PAL: 25fps), which cannot be exceeded. Remaining frame number of the group is displayed at the left bottom of the screen whenever the frame number of each camera is modified.

Note

Each camera belongs to one and only one group and can share the total frame per second of the group up to

25/PAL or (30/NTSC). In case of alarm recording the recording speed of alarmed camera is automatically increased to a possible maximum value. The value can be calculated as follows: If the number of alarmed cameras is

n

and the signal system is PAL, then the recording speed of alarmed camera is

[

25

( 4

n

)

×

1

]

/

n

. For example, if there is one alarmed camera, the channel will be recorded at the speed of 22 fps while other 3 channels will be recorded at the speed of 1 fps. Likewise, if there are two alarmed cameras, those channels will be recorded at the speed of 11 fps each while other two channels will be recorded at the speed of 1 fps.

The connecting channels of each group are shown below.

Group 1=Channel number 1,5,9,13 / Group 2= Channel number 2,6,10,14

Group 3=Channel number 3,7,11,15 / Group 4= Channel number 4,8,12,16

Setting value will not be saved if the frame number setting exceeds 25 fps. The remaining frame number at the left bottom of the screen is displayed as [-] if the frame number setting exceeds 25 fps. In this case, error message appears, and frame number will not be saved even though [Save] button is pressed. Set the frame number so that the total frame number does not exceed 25 fps.

To set frame number by each group, check the remaining frame number after setting the frame number for each group, then press the [Save] button. The setting value will not be saved if there is wrong setting for any group.

6.5.3.

Quality

Set the recording quality for the corresponding channel according to resolution setting by tenth (10-unit) between 10~100. In general, 60~90 is the average extent for setting, where 10 is the lowest quality, and 100 is the highest quality.

The setting value directly influences the byte size per image. For example, the byte size decreases as quality goes lower. In this case, blocking (mosaic) phenomena tends to appear, which is the artifact caused by high compression. In contrast, blocking phenomena disappears as quality goes higher. In this case, the required storage space per image increases, which leads to shortening of total recording period. Therefore, give consideration to the necessary recording period, importance of each camera image, and quality of analog signal when setting the recording quality. If extending the recording period in high quality, refer to 6.5.4. The byte size decreases when the sensitivity setting decreases.

When the quality increases over 80, picture quality increases in small degree, but the byte size increases to great extent.

Be cautious while using low performance camera, since it tends to be much noisier at nighttime and might cause the increase of byte size when high quality value is set for the camera.

6.5.4.

Sensitivity

Set the motion sensitivity value based on motion detection between 10~100. Higher value saves any movement without skipping, and lower value skips small movements to extend the recording period.

The default is 70, and it is recommended not to change, with the exception of special cases. To change this value, refer to the

“Sensitivity Setting” in the appendix to get full understanding, and try different values to find the most suitable value corresponding to the circumstances.

Page 37

3040-00052

DigiOpG2 Digital Video Recorder

6.6

Camera-Title & Schedule

Set the title of the connected camera and recording schedule.

Page 38

6.6.1.

Title

Input the camera title of selected camera. Inputted camera title is displayed as OSD (On-Screen Display) and is also stored in the recorded files afterwards. Therefore, when the file is played in the system or remote site, the camera title will be indicated as that stored in the file during recording.

Default camera title is “CHn” where n is the channel number. It can be up to 16 characters maximum including letters, capital letters, numbers, or spaces. The screen below indicates a keyboard in which to input letters for Title.

6.6.2.

Start & End

Set recording start and end time for the camera. Start time indicates that the recording is started on exact time (0 minutes 0 seconds), and end time indicates the images are recorded until the assigned time (59 minutes 59 seconds). Hour is displayed in 24-hour unit, default is “0~24”. That is, if it is recorded 24 hours every day.

It will record normally even if the start and end time is reversed. For example, if the schedule is set as “18~9”, it records from

18.00 to 09.00 the next day for every day.

Note

Even if a camera is not set to record according to a schedule, it can record by means of sensor-activated recording.

Select the Record ‘Off’ in the “Camera-Record” when you want sensor-activated recording only.

3040-00052

DigiOpG2 Digital Video Recorder

6.7

Camera-Color

Set the brightness, contrast, color and tint of the connected camera.

6.7.1.

Bright

Adjust the brightness (shades) of the channel. If the entire image is dark or bright to a great extent, adjust to the adequate value. Setting values are 1~100.

6.7.2.

Contrast

Adjust the contrast, which is the ratio of brightness to darkness of the image. Greater the value, bright side becomes brighter, and dark side becomes darker. In case the value is increased to the extent where too much saturation is not observed in the image, higher contrast can be helpful to display the image vividly. Setting values are 1~100.

6.7.3.

Color

Adjust the color density. In most cases except for the deterioration of cameras or very low quality cameras, the adjustment of this value is not required. Setting values are 1~100.

6.7.4.

Tint

Set the color hue of connected cameras. In most cases except for the deterioration of cameras or very low quality camera, the adjustment of this value is not required. Setting values are 1~100.

Page 39

3040-00052

DigiOpG2

6.8

Camera-Audio & P/T/Z

Set the camera audio and P/T/Z environment.

Digital Video Recorder

6.8.1.

Audio

Select whether to use audio recording. Select On/Off in the audio tap for each camera.

Note

Use amplifier-equipped devices when connecting to the audio input/output device.

6.8.2.

Audio-CH

Select the audio channel to use among the 4 audio input channels.

6.8.3.

P/T/Z Address

Set the P/T/Z driver address of the connected camera.

Check the below items for proper P/T/Z operation.

1.

Check if the protocol of all P/T/Z controllers connected to the system is in accordance.

2.

Check if the communication setting including baud rate of all P/T/Z controllers is in accordance with the assigned value for that P/T/Z protocol.

3.

Check if the address of all controllers is in accordance with the controller address assigned in the setting menu for that channel.

4.

Check if the power of the P/T/Z controller is turned on.

5.

Check if wiring to P/T/Z controllers is correct.

Page 40

3040-00052

DigiOpG2 Digital Video Recorder

6.9

Alarm-Input

This is the setting menu screen for alarm-activated recording.

Page 41

6.9.1.

Camera

Select an alarmed camera for the alarm.

Alarmed camera will be recorded when corresponding sensor is activated.

Note

Even if a camera is not set to record according to the schedule, it can be recorded by means of sensor-activated recording.

Note

Each camera belongs to one and only one group and can share the total frame per second of the group up to

25/PAL (or 30/NTSC). In case of alarm recording, the recording speed of alarmed camera is automatically increased to a possible maximum value. The value can be calculated as follows: If the number of alarmed cameras is

n

and the signal system is PAL, then the recording speed of alarmed camera is

[

25

( 4

n

)

×

1

]

/

n

. For example, if there is one alarmed camera, the channel will be recorded at the speed of 22 fps while other 3 channels will be recorded at the speed of 1 fps. Likewise, if there are two alarmed cameras, those channels will be recorded at the speed of 11 fps each while other two channels will be recorded at the speed of 1 fps.

The connecting channels of each group are as shown below.

Group 1=Channel number 1,5,9,13 / Group 2= Channel number 2,6,10,14

Group 3=Channel number 3,7,11,15 / Group 4= Channel number 4,8,12,16

Setting value will not be saved if the frame number setting exceeds 25 fps. The remaining frame number at the left bottom of the screen is displayed as [-] if the frame number setting exceeds 25 fps. In this case, error message appears, and frame number will not be saved even though [Save] button is pressed. Set the frame number so that the total frame number does not exceed 25 fps.

To set frame number by each group, check the remaining frame number after setting the frame number for each group, then press the [Save] button. The setting value will not be saved if there is wrong setting for any group.

3040-00052

DigiOpG2 Digital Video Recorder

6.9.2.

Start & End

Select the sensor start and end time to set the sensor-operating schedule. Ranges for start and end time is identical to recording schedule for the camera. Hour display format is 24-hour basis, and default is “0~24”. For example, if setting schedule is 6~18, then sensor input operates from 6:00:00 to 17:59:59.

Note

Be cautious when setting the alarm schedule. If the sensor is inputted outside of time of the schedule, the system will ignore the activation of the sensor and take no action.

6.9.3.

Type

Select the sensor type between N/O(Normal Open) and N/C(Normal Close). Circuit of N/O type is usually open, and the activation of the sensor occurs at the time of close, and N/C type works the reverse way.

Note

Check the setting of the sensor type (N/O or N/C), if the sensor does not operate properly.

The alarm might not function if the actual connecting sensor type and the sensor type in the system setting are inconsistent.

Page 42

3040-00052

DigiOpG2 Digital Video Recorder

6.10

Alarm-Output

This is to set alarm actions regarding recording and relay output.

6.10.1.

Relay

Select the relay number to operate.

6.10.2.

Alarm Mode

Select either Set or Duration depending on the desired alarm action.

Set:

In this mode, the alarmed camera will be recorded (at the recording speed described in 6.9.1) during the setting time in Dwell tab from the moment sensor is activated. i.e. Sensor activation triggers alarm-activated recording, regardless of the deactivation of the sensor during alarm action.

Duration:

In this mode, the alarmed camera will be recorded (at the recording speed described in 6.9.1) upon sensor activation. i.e. The deactivation of the sensor stops the alarm-activated recording.

The corresponding relay will function in accordance with recording if the relay output is selected in the sensor, i.e. the relay starts when alarm-activated recording starts and ends when alarm-activated recording stops.

6.10.3.

Dwell

Set the period for which the alarmed camera will be recorded and the relay output is turned on. The recording stops and alarm output is turned off when the setting period is elapsed. Set the alarm-operating period (5~99 seconds).

Page 43

3040-00052

DigiOpG2 Digital Video Recorder

6.11

Tools-System Information

This is the system information screen of EDNS-3000 series.

Note

The details in the information screen can be different based on the model number and system environment.

Page 44

6.11.1.

Signal System

The type of video signal is displayed: NTSC or PAL.

6.11.2.

Software Version

Software version installed in the system is displayed.

6.11.3.

Hardware Version

Hardware version of the system is displayed.

6.11.4.

HDD Usage

Hard disk usage is displayed. (Used/Total HDD space (Remaining space%))

6.11.5.

IP Address

IP address of the system is displayed.

6.11.6.

MAC Address

MAC address of the system is displayed.

6.11.7.

Daylight Saving

Country of the daylight saving time is displayed.

6.11.8.

Network Connection

The number of clients (channel basis) currently connected to the system using RemoteAgent is displayed.

3040-00052

DigiOpG2 Digital Video Recorder

6.12

Tools-System Upgrade

This screen appears during system upgrade. Enter the host address if upgrading through LAN or TFTP.

Page 45

6.12.1.

Select

Select the method to upgrade the system.

1.

LAN: will be supported in the future

2.

TFTP: to upgrade via TFTP protocol. The IP address of the host TFTP server is required.

3.

CD-ROM: to upgrade with the internal CD-RW (option)

Note

The following sequence is how to upgrade using the internal CD-RW.

1.

Prepare upgrade image CD.

2.

Put the prepared CD inside the CD-RW of the system.

3.

Select CD-ROM from Select category of the upgrade menu. Then, select the [Start] button.

4.

When the upgrade is completed without any error, no error message will be displayed and the system will automatically reboot after upgrade.

5.

The upgrade image CD must read the “hdvr.bin” image file at the root folder. Be cautious that the image file name must be in small letters, “hdvr.bin”.

6.12.2.

Host Address

Input the host server address of LAN connection.

6.12.3.

Version

Displays the version of the software that is being downloaded.

6.12.4.

Progress

Displays the progress while upgrading.

6.12.5.

Start

Starts the upgrade when pressed.

3040-00052

DigiOpG2 Digital Video Recorder

6.13

Tools-System Default

This screen allows the users to return to the default factory setting. In this case current setting values will be ignored.

All setting values, except for the network setting and passwords, return to default value when [Yes] button is pressed.

Note

In the System Default setting, the entire values will be returned to the default setting, thus desired setting values should be kept separate for future use.

Page 46

3040-00052

DigiOpG2

6.14

Quit

This screen exits the setting menu of the system.

Digital Video Recorder

6.14.1.

Log Off

Log off the currently logged-on user. In order to return to the setting menu or to manage the system, login by inputting

<User> or <Admin> password, respectively. Be sure to log-off, or unauthorized persons can alter your settings and use the system in a bad way.

6.14.2.

Close Menu

Return to the previous status by closing the setup menu.

Page 47

3040-00052

DigiOpG2 Digital Video Recorder

7.

Appendix

7.1

Sensitivity Setting

Motion Detection and Motion Detection Recording

Motion detection is to quantitatively calculate the movement of objects in a series of video images from camera and to determine if it is over user-defined threshold (motion sensitivity). In motion detection recording, an image with small movement will be skipped and not be recorded while an image with big movement will be recorded without skip. If motion sensitivity is set to a value below 100, then recording mode will be changed into ‘Motion Detection Recording’ to activate this feature.

Continuous Recording

When motion sensitivity is set to 100, the recording mode is changed from motion detection recording to continuous recording. In this mode, every motion and camera noise will be saved regardless of the quantity of the motion.

Conversely, the required storage space per hour increases at least 2~3 times, compared with motion detection recording, and the total recording period is decreased to that extent. Therefore, be cautious with settings for important camera channels so that no motion is skipped.

Noise Detection

AGC (Auto Gain Control) circuit amplifies the output signal of CCD in dark light when the AGC feature of the camera is turned on (normally selected as ‘on’). At this time, the thermal noise of CCD is amplified as well, displaying numerous small, insignificant red and blue spots.

Due to the high frequency nature, such CCD noise decreases the compression efficiency and, consequently, leads to increased byte size per image. The size is almost 2~3 times bigger than that with high motion image at daytime. Besides, since the distinction between real motion and noise is practically impossible, motion detection algorithm can save unnecessary images of no real motion, but noise, resulting in continuous recording. As a result, hard disk will be filled with unnecessary images with noise.

To decrease such unnecessary fill-up of storage with noisy images at night, noise detection feature is included in the motion detection feature. It makes it possible to skip the images of no motion but noise.

The lower the motion sensitivity setting is, the higher the efficiency of the noise detection is. In order to set the motion sensitivity to 90, the use of cameras with high CCD sensitivity is recommended.

Page 48

3040-00052

DigiOpG2 Digital Video Recorder

The table below indicates recording-related trend of each item according to the motion sensitivity setting.

Setting

Value

100

90

70~80

10~60

Recording

Method

Continuous recording

Motion detection recording

Motion

Sensitiveness

Saves all

Saves images of small motion

Saves if there is motion

Daytime Storage

Space

Much storage space is required due to continuous recording

Less than half of continuous recording, but still high storage space is required

Normal storage space is required

If the setting is too low, even big motion will be skipped

Required storage space decreases as the value decreases

Effects of Night

Noise

Saves all

Saves almost all due to high setting

Frequently skips due to low setting

Skips due to low setting

Nighttime Storage

Space

Reaches the maximum of byte size if noise is high

Required storage space decreases if skip happens. If not, saves as continuous recording

Considerably small storage space is required due to frequent skipping

Required storage space decreases as the value decreases

Page 49

3040-00052

DigiOpG2

7.2

System Specifications

Digital Video Recorder

Hardware

CPU

RAM

HDD

OS

Video Input

Display Speed

Screen Modes for Live

Display

Recording Speed

352x240

640x240

720x480

Monitor Output

Recording Resolution

Compression Method

Byte Size per Image

Recording Modes

Recording Schedule

Motion Detection

Sensor / Camera / Alarm I/O

Audio Input / Output

Sensor / Alarm

P/T/Z Control & Port

LAN

Transmission Speed and No. of Connections

Remote Transmission

Remote Control

CD-RW INTERNAL

System Recovery after Power Failure

System Operation

Advanced Functions

Storage Temperature and Humidity

Operating Temperature and

Humidity

Power

Dimension

Weight

Remote S/W

3120-16EP 3120-16EPC 3240-16EP

32bit RISC

64MB

120GB 240GB

Embedded Linux

16Ch, NTSC/PAL Selectable

400 PAL:400fps (NTSC:480fps, Real time Display)

3240-16EPC

1/4/6/8/9/10/13/16 Channel Mode

200fps (NTSC 240fps)

100fps (NTSC 120fps)

50fps (NTSC 60fps)

Analog (BNC) / S-Video / Supports 1 Spot Output (BNC) / Loop-Out

NTSC: 352x240, 640x240, 720x480

PAL : 352x288, 640x288, 720x576

Enhanced MPEG-2 (H/W Compression)

3~5Kbyte @352x240 (PAL: 352x288)

5~10Kbyte @640x240 (PAL: 640x288)

6~16Kbyte @720x480 (PAL: 720x576)

Continuous, Motion Detection and Sensor Activated

Setting Recording Schedule per camera

Supports the Setting of Motion Sensitivity per Camera

M : N Mapping

4 Input / 1 Output (ADPCM)

16 Input / 4 Output

RS-485

10/100BASE-TX Ethernet

Same as Recording Speed for each Channel

Max 16ch Connection (16 Video Transmission at the same time)

Multi-to-Multi Connection, Multi-channel Transmission

Remote Live Viewing, Remote Playback and Remote File copy

Playback, Network Transmission, Recording (Triplex operation)

Remote Pan/Tilt/Zoom/Focus/Iris

NO YES NO

Auto-Rebooting and Journaling File System

Auto-Scan and Recovery for Data

Button on Front Panel and IR Remote Controller

Auto Page Sequencing, Event Log Viewer, Access Control by Password,

LED Indicator for Various status

-20~65@ / 20~95%RH

YES

5~40@ / 20~80%RH

AC115~230V, 50/60Hz (Free voltage)

420(W) x 88(H) x 440(D) mm

11Kg (Approximate) / 13Kg (including the packing, Approximate)

DigiOp RemoteAgent S/W (16ch)

*The system specification can be modified without notification. Standard spec. based on JAN, 1st. 2004

Page 50

3040-00052

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals