INSTALLATION
● Thank you for purchasing the our product. Before installing, please read the instruction carefully and keep it for future reference.
Notice
●
●
●
●
Please, follow the step-by-step instructions for proper installation. Any damages caused by faulty installation shall be imputed to the users.
To avoid a short circuit, do not pull the wires when installing the unit. Do not break or modify the wires either.
Do not disassemble or change any parts.
Maintenance and repairs should be executed by our professionals only.
◎ Mark Meaning:
NOTE Yo u could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
WARNING!
CAUTION!
Some processes must be followed to avoid damages to yourself or the public.
Some processes must be followed to avoid the damage to the vehicle.
FLASH
PRESS THE
BUTTON
ONCE
LIGHT ON
PRESS THE
BUTTON 3
SECONDS
1-1
Accessories
1
Meter X 1
2
Main wiring harness X 1
3 RPM wire (TYPE A) X 1 4 RPM wire (TYPE B) X 1
5
Active speed sensor X 1
6 M8 / S type speed sensor bracket X 1
7 M10 / S type speed sensor bracket X 1
8 M5 X 5L mm Hexagon screw X 2
9
4 mm Allen key X 1
10
3 mm Allen key X 1
11
2 mm Allen key X 1
12
M5 X 12L screw X 2
13
M4 X 10L screw X 2
14
M4 washer X 2
15
Meter bracket X 1
NOTE Contact your local distributor, if the items received in the box are not the same as the items listed above.
1-2
Accessories
1 2 3 4
RUNNER
SR
X-FIGHT
BOOSTER
5 Meter bracket
JIS TYPE A
NOTE Some of the optional accessories may not be available in your area. Contact your local distributor to obtain more information.
2-1
Wiring installation instructions
Orange - L turn signal light (+12 V)
Blue - R turn signal light (+12 V)
Yellow - High beam light (+12 V)
Gray - Oil light (+12 V / ─)
White - Neutral light (─)
Green - Fuel
Purple - Engine light (─)
Mid-way connector
Red - Postive pole
(Connect to the battery DC 12V)
Brown / Red - RPM wire please connect it to the suitable position according to the models
Main power switch wire reference:
YAMAHA
HONDA
SUZUKI
KAWASAKI
KYMCO
SYM
PGO
Power
Red
Red
White
Red
Red
Red / White
Key on
Brown
Red / Black
Black
Brown
Black
Black
Orange
Ground
Black
Green
Green
Black / Yellow
Green
Green
Black
Connect to speed sensor
Brown - Positive wire should be connect to main power switch
Black - Ground wire connect to the negative pole of the battery (must be a good ground)
Active speed sensor (Accessories 5)
RPM wire reference:
YAMAHA
HONDA
SUZUKI
KAWASAKI
APRILIA
BMW
BENELLI
Yellow / Black
Yellow / G
Yellow / reen
Blue
Light Blue
Gray / Violet
Black
Gray / Violet
BUELL
CAGIVA
DUCATI
H-D
MV
TRIUMPH
Pink
Gray / G reen
Gray / G reen
Gray / Yellow
Red
R PM wire (TYPE B)
(Accessories 4)
R PM wir e (TYPE A)
(Accessories 3)
A
Fuel indicator wire reference:
YAMAHA
HONDA Yellow / White
SUZUKI
KAWASAKI
Green
Yellow / White
Black / L Green
KYMCO
SYM
PGO
Yellow / White
Yellow / White
Gray
The fuel sensor is electronic type, do not connect in parallel with the original wire - otherwise the fuel gauge won't display.
wire might damage the instrument.
C
Ignition coil positive
Flywheel
Coil
B
R PM wire (TYPE B)
(Accessories 4)
Pick up
Spark plug wire
NOTE
Tachometer
NOTE When connecting the power wire, please follow carefully the instruction. If the red & brown wires are connected in parallel, the meter won’t work properly.
Motor oil indicator can be set up, install as two stroke motor oil indicator, or other positive(+12V) or negative actions' indicator.
The RPM wire installation
We recommend installing the R type spark plug or low-resistance spark plug cap at the same time.
A. Connect the RPM wire (Type A) on the spark plug wire by connecting the male and female connectors.
B. Connect the RPM wire (Type B) to the pick up sensor.
C. Connect in parallel the RPM wire (Type A) with the original tachometer signal wire.
The best signal source will be in order as C>B>A, we will suggest you to check different ways if you have problems to get the
RPM signal.
2-2
Installation instruction
5
6 7
4
8
1
2
3
2
When installing, please follow the steps bellow.
1. M5 x 12L screw x2 (Accesories 13)
2. Meter bracket for handle bar (Accesories 12)
3. Fix the bracket on handle bar (7/8 inch)
4.Bracket x1 (Accesories 12)
5. Meter (Accesories 1)
6. Meter board (Accesories 12)
7. M4 washer x2 (Accesories 15)
8. M4 x 10L screw x2 (Accesories 14)
NOTE Adjust the meter to the proper angle before tightening the handle bar bracket screws.
Special instruction for meter fix board.
A. Push meter bracket clip up to lock meter fix board with meter on bracket
B. Push meter bracket clip down to release meter fix board with meter on bracket wh041ba02a(P6-1)
MOTO / SCOOTER
S type speed sensor bracket instruction
Install the s type sensor bracket.
Install the speed sensor on the bracket.
sure that the sensor could face the magnet to prevent bad speed signal or no signal!
Adjust the distance between sensor and distance is under speed signal.
1 mm for catching good
MOTO / SCOOTER
L type speed sensor bracket instruction
Please install the L bracket and the anti-slip proper height and angle.
Install the speed sensor on the bracket.
the front fork. Please make sure the disc screw could pass the hole on the bracket for you to install the sensor into the same hole for catching the speed signal.
magnet. We suggest you to make sure the speed signal.
1 mm for catching good
The active speed sensor could be installed by the metal parts to detect the speed.
EX. 1 The disc screw.
speed signal.)
EX. 3 The sprocket to detect the disc gap. (Please make sure the distances between the gaps are the same in advance to avoid wrong
speed signal.)
EX. 4 Rear disc - detect the gap between the disc.
EX. 1 speed sensor the detect range
EX. 2
、
4 speed sensor the detect range speed sensor speed sensor
The best detect area: The edge of the hexagon socket screw.
Please don't catch the signal from the middle hole of the hexagon socket screw to avoid wrong signal.
speed sensor
The best detect area: Please detect the speed signal from the gaps of the disc.
Please note that there are discs with the gaps in different difference, and this method will not work on it!
the detect range
EX. 3 speed sensor the detect range speed sensor
The best detect area: The middle of the screws.
Some hexagon screw center is with a small hole in the center in this case,we will suggest you to catch the signal from the edge of the screw like the hexagon socket screw. speed sensor
The best detect area: Please detect the speed signal from the gaps of the sprocket.
Please note that there are sprockets with the gaps in different difference, and this method will not work on it!
3-1
Basic function instruction
Maximum speed record
●Display range : 0 ~ 360 km/h (0 ~ 225 mile)
Maximum RPM record
●Display range : 0 ~ 15,000 RPM
Average speed record
●Recording range :
0 ~ 360 km/h (0 ~ 225 MPH)
Speedometer
●Display range :
0 ~ 360 km/h (0 ~ 225 mile)
●
●
Indication light
●Neutral (green light)
●
●
Right indication light (green light)
Water temperature (red light)
●
●
Motor oil (red light)
Engine (yellow light)
Fuel (yellow light)
Left indication light (green light)
●High beam light (blue light) Select
Tachometer
●Display range : 0 ~ 10,000 RPM、0 ~ 12,000 RPM、0 ~ 15,000 RPM
Adjust
Fuel Level
●Setting range : 100Ω、 250Ω
、 270Ω、510Ω、1200Ω、
SWITCH、USER
Low fuel warning
●Setting range : 10 ~ 50%, when lower than (including) setting value, fuel level symbol will blink.
Total engine operating time
●
●
Display range : 0~99,999.9 hours
Display unit : 0.1 hour
Engine operating time A,B
●
●
Display range : 0~9,999.9 hours
Display unit : 0.1 hour
Odometer
●Display range : 0 ~ 99999.9 km (mile),
return to zero upon exceed.
●Display unit : 0.1 km (mile)
Trip meter A、B
●Display range : 0 ~ 999.9 km (mile),
return to zero upon exceed.
●Display unit : 0.1 km (mile)
Tachometer
●Display range : 0 ~ 15,000 RPM
●Display unit : 10 RPM
Voltmeter
●Display range : DC 8.0 V ~ 16.0 V
●Display unit : 0.1 V
Clock format
●Setting range : 12 - hrs format, 24 - hrs format.
Internal ODO
●
●
Display range : 0 ~ 99,999.9 km (mile) , user unadjustable.
●
●
Display unit : 0.1 km (mile)
External ODO
Setting range : 0 ~ 99,999 km (mile)
Setting unit : 1 km (mile)
Clock
● Setting range : 0：00 ~ 23：59 (24 - hrs format),
1：00 ~ 12：59 (12 - hrs format)
Motor oil maintenance millage
● Display range : SI unit :
500 (~ 8,000 km, user adjustable) ~ -999 km, automatic decrease according to the increase of total millage.
●
●
Display range : Inch :
300 (~5,000 mile user adjustable)~ -999 mile, automatic decrease according to the increase of total millage.
Display unit : 1 km (mile)
3-2
Function, setting instructions
● Speedometer
○
○
○
Display internal
Odometer
Trip meter A、B
Display range : 0 ~ 360 km/h (0 ~ 225 MPH)
Will blink when exceed range.
Display unit : 1 km (mile)
<0.5 second
Display range : 0 ~ 99,999.9 km (mile), return to zero upon exceed.
Display unit : 0.1km (mile)
Display range : 0 ~ 999.9 km (mile), return to zero upon exceed.
Display unit : 0.1km (mile)
● Motor oil maintenance millage
Display range : SI unit : 500 (~8000 km, user adjustable)
~ -999 km, automatic decrease according to the increase of total millage.
Display range : Inch : 300 (~ 5000 mile user adjustable)
~ -999 km, automatic decrease according to the increase of total millage.
Display unit : 1 km (mile)
○ Maximum speed recordDisplay range : 0 ~360 km (0 ~ 225 mile)
○
○
Display unit : 1 km (mile)
Average speed recordRecording range : 0 ~ 360km/h (0 ~ 225 MPH)
Tire circumference Setting range : 300 ~ 2,500 mm
Setting unit : 1 mm
○ Sensitive point
●
○
○
Tachometer
Display internal
Stage tachometer
Setting range : 1 ~ 20 points
Setting range : 1 point
Display range : 0 ~ 15,000 RPM
Display unit : 10 RPM
<0.5 second
○ Hour meter A 、 B
Display range : 0 ~ 10,000 RPM、
0 ~ 12,000 RPM、0 ~ 15000 RPM
Display unit :
0 ~ 10,000 RPM (333 RPM each stage)
○
○
●
○ MAX RPM record
0 ~ 12,000 RPM (400 RPM each stage)
0 ~ 15,000 RPM (500 RPM each stage)
Display range : 0 ~ 15,000 RPM
Display unit : 10 RPM
The RPM input signal number setting Setting range : P-0.5,P-1~P-25
The RPM input pulse Setting range : lo-Act, Hi-Act
Total hour meter Display range :0 ~ 99,999.9 hour
Display unit : 0.1 hour
Display range :0 ~ 9,999.9 hour
Display unit : 0.1 hour
●
○
○
○
●
●
○
○
●
Fuel level
Staged fuel gauge
Digital fuel gauge
Low fuel warning
Volt meter
Clock format
Clock (hours)
Clock (minute)
Internal ODO
Setting range : 100Ω、 250Ω,、270Ω、510Ω、
1200Ω、SWITCH、USER
Setting range : 10 stage display
Warning range : Fuel level warning stage below
(including) setting value, fuel level symbol will blink.
Setting range : 0 ~ 100 %
Setting unit : 10 %
Setting range : 10 ~ 50 %, when lower than
(including) setting value, fuel level symbol will blink.
Setting unit : 10%
Display range : DC8.0 V ~ 16.0 V
Display unit : 0.1V
Setting range : 12-hrs format, 24-hrs format
Setting range : 0 ~ 23 (24-hrs format),
1 ~ 12 (12-hrs format)
Setting unit : 1 hour
Setting range : 00:59 minutes
Display range : 1 minute
Display range : 0~99999.9 km (mile), user unadjustable
● External ODO
● Backlight color
●
●
Effective voltage
Effective temperature range
●
●
●
●
Meter standard
Meter size
Meter weight
Indicator light
Display unit : 0.1 km (mile)
Setting range : 0~99999 km (mile)
Setting unit :1km (mile)
Display range: white
DC 12 V
-10 ~ +60 °C
JIS D 0203 (S2)
120 x 46 x 20 mm
Around 240 g
Neutral (green light)
Right indication light (green light)
Water temperature (red light)
Motor oil (red light)
High beam light (blue light)
Left indication light (green light)
Fuel (yellow light)
Engine (yellow light)
NOTE Any design and specification changes will not be notify.
wh041ba02a(P6-2)
3-3
Meter size
120 mm
3-4
Select button function instruction
●In the clock screen, press the Select
button one time to enter the volt
screen.
●In any screen, press and hold the
Select buttons for 3 seconds to switch
between rpm and fuel bar screen.
●In the volt screen, press the Select
button one time to enter the fuel
level screen.
3-5
Adjust button function instruction
●In the ODO sereen, press the Adjust
button to enter the Trip A screen.
●In the ODO sereen, press the
Select+Adjust buttons for 3 seconds
to enter settings (Please refer to 4).
●In the Trip A screen, Press the Adjust
button to enter the Trip B screen.
●Press and hold the Adjust button for 3
seconds to reset Trip A screen.
●In the Trip B screen, press the Adjust
button to enter the oil maintence
mileage screen.
●Press and hold the Adjust button for 3
seconds to reset Trip B screen.
●In the oil maintence mileage screen,
press the Adjust button to enter the
total hour meter screen.
●Press and hold the Adjust button for 3
seconds to reset oil maintence mileage
screen.
●In total hour meter screen, press the
Adjust button to enter the hour meter
A screen.
3-6
The settings screen description
8 mm
37 mm 20 mm
●In the fuel level screen, press the
Select button one time to go back to
the clock screen.
●In the clock screen.
●Total millage screen - Press and hold the Select + Adjust button for 3 seconds to
enter setting screen.
●Press the Adjust button to select setting screen for Circumference and sensing
pointsetting, RPM pulse setting, Fuel gauge resistance setting (Fuel level manual
setting / Fuel level resistance auto detection setting / Fuel warning setting), Clock
setting, Backlight brightness setting, Oil maintenance mileage setting, Speed unit
setting, External ODO, Internal ODO.
●In any setting screen, hold the Select button for 3 seconds to return to main screen.
NOTE
NOTE
In settings screen, button is not pressed in 30 seconds, or speed > 3 km/h, will automatically return to main screen.
After exiting settings screen, it will record the parameters.
●In the hour meter A screen, press the
Adjust button to enter the hour meter
B screen.
●Press and hold the Adjust button for 3
seconds to reset hour meter A screen.
●In the hour meter B screen, press the
Adjust button to enter the Max. record
screen.
●Press and hold the Adjust button for 3
seconds to reset hour meter B screen.
●In the Max. record screen, press the
Adjust button one time to enter the
Average speed record screen.
●Press and hold the Adjust button for 3
seconds to reset Max. record screen.
●In the Average speed record screen,
press the Adjust button one time to
enter the ODO sereen.
●Press and hold the Adjust button for 3
seconds to reset Average speed record
screen.
●In the ODO sereen.
4
Enter settings and function index menu
●Press and hold the Select + Adjust
button for 3 seconds to enter setting
screen.
●Function index a 1. Circumference and sensing pointsetting a 2. RPM pulse setting a 3. Fuel gauge resistance setting
Fuel level manual setting
--------------------------
----------------------------------------------
------------------------------------
-------------------------------------
Fuel level resistance auto detection setting
Fuel warning setting a 4. Clock setting a 5.
--------------------
------------------------------------------
----------------------------------------------------
Backlight brightness setting -------------------------------------a 6. Oil maintenance mileage setting a 7. Speed unit setting a 8. External ODO a 9. Internal ODO
---------------------------------
-----------------------------------------------
---------------------------------------------------
----------------------------------------------------
4-1
4-2
4-3
4-3-1
4-3-2
4-3-3
4-4
4-5
4-6
4-7
4-8
4-9
4-1
Circumference and sensing pointsetting
●Press the Select button to enter the
circumference and sensing point
setting screen.
●Press the Adjust button to choose
the setting number.
●Please measure the tire circumference (
The tire you will install the sensor on) and
make sure the number of magnet sensor
point (You could install the magnet into
the disc screw or the sprocket screw.)
●The speed displayed on the meter will be
affected by the setting, please make sure
the setting number is correct before you
make the setting.
Please reset this setting value when you change a different size tire.
●Press the Select button to enter the
sensor point setting.
●EX. The circumference setting is
changed from 1,000 mm to 1,300 mm.
●Example：If the tire circumference is
1,300 mm.
●Press the Select button to choose
the setting number.
●EX. Now the tire circumference is
setting from 1,000 mm.
Now the digit in thousands setting number is flashing!
NOTE Setting range：300 ~ 2,500 mm
Setting unit：1 mm
●Example：If the sensor point is
setting 6P.
●Press the Adjust button to choose
the setting number.
●Ex. Now the sensor point is setting
from 1P.
Now the setting value is flashing!
NOTE Sensitive point：1 ~ 20
●Press the Select button to go back to
the circumference and sensing point
setting screen.
●Ex. Now the sensor point is setting
from 1P to 6P.
P.S.
●You could define the
valve as the starting
point and the terminal
point to measure the
wheel circumference
with a measuring tape.
●Press the Adjust button to enter next
operation setting.
wh041ba02a(P6-3)
4-2
RPM pulse setting
●Press the Select button to enter the
RPM pulse setting screen.
●EX. You want to connect the RPM
signal wire to the pick up signal and
there are 13 flywheel signals per turn.
●Press the Adjust button to choose the
setting number.
Currently setting value will blink.
NOTE Setting range: 0.5、1 ~ 25
0.5
1
2
3
4
5
6 2C-6P
4C-1P
2C-1P 4C-2P
2C-2P 4C-4P
2C-3P
2C-4P
4C-6P
4C-8P
4C-10P
4C-12P
2 RPM signals per 1 ignition.
1 RPM signal per 1 ignition.
1 RPM signal per 2 ignition.
1 RPM signal per 3 ignition.
1 RPM signal per 4 ignition.
1 RPM signal per 5 ignition.
1 RPM signal per 6 ignition.
CAUTION!
with one single piston are igniting every
360 degree once, so the setting should be the same as the bike with 2-cycle and one piston engine.
●Press the Select button to enter
waveform setting screen.
● EX. Setting engine ignition angle from
P-1 to P-13.
●Example : To set waveform to high
waveform (Hi-Act).
● Press the Adjust button to choose the
setting number.
Currently setting value will blink.
NOTE
NOTE
Setting range：Hi-Act、Lo-Act
During RPM signal detection, if there is any bad sensing or interference, please select another RPM sensing waveform.
4-3
Fuel gauge resistance setting
●Press the Select button to enter the
circumference and sensing point
setting screen.
●Example: If the vehicle is a YAMAHA
T-MAX 530, it's resistance is 100 Ω
according to the service manual.
●Press the Adjust button to choose the
setting number.
Currently setting value will blink.
NOTE The fuel gauge resistance setting range：USER、100 Ω、
250 Ω、270 Ω、510 Ω、
1200 Ω、SW (turn off)
●Press the Select button to enter rpm
stage setting screen.
●EX. Setting from high wave (Hi-Act) to
low wave (Lo-Act).
●Example : To set rpm stage value as
10,000 RPM.
●Press the Select button to choose
the setting number.
●EX. Current rpm stage value is
15,000 RPM.
Currently setting value will blink.
NOTE Setting range：10,000、
12,000、15,000 RPM。
●Press the Adjust button to choose
the setting number.
●Press the Select button to return to
rpm stage setting screen.
● EX. Setting rpm stage value form
15,000 RPM to 10,000 RPM.
●Press the Adjust button to enter next
operation setting.
NOTE Custome fuel level resistance:
1) Manual - Please check 4-3-1
Fuel Level Resistance Manual
Setting Instructions.
2) Auto - Please check 4-3-2
Fuel Level Resistance Auto
Setting Instructions.
NOTE Fuel meter will be displayed with the wiring connected.
●Press the Select button to enter 4-3-3
fuel warning setting screen.
● EX. Setting fuel meter's resistance
value from 100 to 270.
4-3-1
Fuel level manual setting
●Press the Select button to enter the
lowest fuel level's resistance setting
screen.
●Example：For YAMAHA T-MAX 530,
according to the service manual, the
fuel tank resistance from low to high
is 90 - 100 Ω (the lowest) and 4 - 10 Ω
(the highest).So enter the setting
value as 10 Ω .
P.S.
●You could find your fuel level sensor
resistance range in the electronic
components section in the service
manual.
●Normally, we will recommend to choose the
closest number set as the range to ensure that riders
will not run out of gas before the fuel level indication. example, for
YAMAHA T-MAX it’s 90 - 100 Ω and 4 - 10 Ω , in which case we will
suggest to use 90 - 10 Ω as the lowest and highest range.
●Example：To set minimum fuel level
as 90 Ω.
●Press the Select button to choose
the setting number.
Currently setting value will blink.
●Press the Adjust button to choose
the setting number.
● Press the Select button twice to enter
maximum fuel resistance value setting
screen.
● EX：Setting minimum fuel level
from 0 to 90.
●Example：To set maximum fuel level
as 10.
●Press the Select button to choose
the setting number.
Currently setting value will blink.
●Press the Adjust button to choose
the setting number.
●Press the Select button twice to enter
4-3-3 fuel warning setting menu.
●EX. The highest fuel level setting is
changed from 0 to 10 Ω.
4-3-2
Fuel level resistance auto detection setting
● Press the Select button to enter the lowest fuel level's resistance auto
detection screen.
●Before detection, ensure that your current
fuel level is in the lowest position that you
would like to have.
●Stop the vehicle for a few seconds to allow
the fuel surface to become steady, then
start the detection of the resistance.
P.S.
●For example of YAMAHA T-MAX 530,
if the fuel surface sensor float in the
lowest position then it will detect the
resistance around
90 Ω.
The lowest position
●Before detection, please ensure your
current fuel level is in the highest
position that you would like to have.
●Stop the vehicle for a few seconds to
allow the fuel surface become steady,
then start the detection of the resistance.
P.S.
●For example the YAMAHA
The highest position
T-MAX 530, if the fuel surface sensor
float is in the highest position then it
will detect the resistance as around 10 Ω.
●Press the Adjust button to detect the
highest fuel level resistance.
●Press the Adjust button to detect the
lowest fuel level's resistance.
●Press the Select button 5 times to go
back to the fuel gauge resistance.
●EX. Automatically detect the highest
fuel level resistance value as 10 Ω.
●Press the Select button 5 times to
enter the lowest fuel level resistance
auto detection screen.
●EX. Auto Detection the lowest fuel
level resistance is 90 Ω.
wh041ba02a(P6-4)
4-3-3
Fuel warning setting
●Example：To set fuel warning value
as 30%.
●Press the Adjust button to choose
the setting number.
Currently setting value will blink.
NOTE Setting range : 10%, 20%, 30%,
40%, 50%.
Fuel meter will not display when fuel meter's wire is not installed.
●Press the Select button to return to
fuel level resistance value setting
screen.
● EX. Setting maximum fuel level from
30% to 10%.
4-4
Clock setting
●Press the Select button to enter the
clock setting screen.
●Example：Changing the 24H.
●Press the Adjust button to choose
the setting number.
Currently setting value will blink.
NOTE Setting range: 12 / 24 H
● Press the Select button to enter time
adjustment (hour / minute) setting
screen.
● EX. Setting time format from 12-hours
to 24-hours.
●Example：To set time(hour) as 10
hours.
●Press the Adjust button to choose
the setting number.
Currently setting value will blink.
NOTE Cursor moving order is：
Hour > Digit in ten minutes >
Digit in minutes
NOTE Setting range：0 ~ 23
4-5
Backlight brightness setting
●Press the Select button to enter the
backlight brightness setting screen.
●Example：You want to set the
brightness at 60 % (3).
●Press the Adjust button to choose
the setting number.
Currently setting value will blink.
NOTE Setting range：
1 (Darkest) ~ 5 (Brightest),
5 different levels available.
Setting unit：20% per level.
The backlight brightness will change immediately after you set the value.
●Press the Adjust button to enter next
operation setting.
●Example：To set time (minute) as 10
minutes.
●Press the Select button to choose
the setting number.
Now the setting value is flashing!
NOTE Setting range：00 ~ 59 minutes.
●Press the Adjust button to choose
the setting number.
● Press the Select button to return to
time setting screen.
● EX. Setting hour/minute from 0 hour
0 minute to 10 hours 10 minutes.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back to
the backlight brightness setting screen.
●EX. The backlight brightness setting is
changed from 5 (100%) to 3 (60%).
●Press the Adjust button to enter next
operation setting.
4-6
Oil maintenance mileage setting
●Press the Select button to enter the
oil maintenance mileage setting
screen.
●Example：To set motor oil millage
value as 4T.
●Press the Adjust button to choose
the setting number.
● EX. Current motor oil millage is 2T.
Currently setting value will blink.
NOTE Setting range : 2T / 4T
●Press the Select button to enter 4T
motor oil millage setting main screen.
● EX. Setting motor oil millage value
from 2T to 4T.
●Example：To set motor oil millage
parameter as 1,500.
●Press the Select button to choose
the setting number.
●EX. Current motor oil millage
parameter is 1,000.
4-7
Speed unit setting
●Press the Select button to enter the
speed unit setting screen.
●Press the Adjust button to choose
the setting number.
4-8
External ODO
●Press the Select button to enter the
external ODO setting screen.
●Example : To set external total millage
value to 12,500 km.
●Press the Select button to choose
the setting number.
Currently setting value will blink.
NOTE Setting range :
0 ~ 99,999 km (mile)
●Press the Adjust button to choose
the setting number.
Currently setting value will blink.
●2-stroke motor oil millage is indicated by external signal warning
(motor oil indicator will lit).
●4-stroke motor oil millage is internally set by the chronograph.
●Press the Adjust button to choose
the setting number.
●Press the Select button to go back
oil maintenance mileage setting
screen.
● EX. Setting motor oil millage
parameter from 1,000 to 1,500.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to go back
speed unit setting screen.
●EX. The speed unit setting is changed
km/h、km to MPH、mlie.
●Press the Adjust button to enter next
operation setting.
●Press the Select button to the
external ODO setting screen.
●EX. The external ODO is changed 0 to
12,500 km.
●Press the Adjust button to enter next
operation setting.
wh041ba02a(P6-5)
4-9
Internal ODO
●Example：Current internal ODO is
50,000 km.
●Press the Select button three seconds
to go back to ODO screen.
User unable to adjust and clearinternal ODO.
NOTE Setting range：
99999.9 km (mlie).
●The main screen.
5
Trouble shooting
The following situation do not indicate malfunction of the meter.Please check the following before taking it in for repair.
Trouble
The meter doesn't work when the power is on.
The meter shows wrong information.
Speed does not appear or appear incorrectly.
The odometer and trip meter are not accumulated or accumulated the wrong data.
Check item
● The power doesn't supply to the meter.
→Please make sure the wiring is
connected.
The wiring and fuse are not broken.
→The battery is broken or the battery is
too old to supply enough power
(DC 8 V) to make the meter work.
● Check the voltage of your battery,and
● make sure the voltage is over DC 8 V.
Make sure the speed sensor is
connected properly.
→Please check if speed sensor is
connected and working properly. Also
check whether the cable of speed sensor
has broken or lose or not.
● Check the tire-size setting.
→Refer to the manual 4-1 circumference and sensing point setting.
● It is possible that the permanent power
wire is not connected properly.
→Check if the red positive wire is
connect propery.
Trouble
Tachometer does not appear or appear incorrectly
The odometer and trip meter is not accumulated or accumulated wrong data.
Fuel gauge does not appear or appear incorrectly.
Check item
● Please check the RPM sensor wiring is
connected correctly.
● Please check the spark plug is R type or
not. If not, please replace the spark plug
with the R type spark plug.
● Please check your setting.
→Please refer to the manual 4-2 RPM
pulse setting.
● It is possible that the permanent power
connect well or not.
●
●
wire is not connected well.
→Please check the red positive wire is
Check your fuel tank.
Check the wiring harness.
→
●
Is the wire connected properly.
Check the tire-size setting.
→Refer to the manual 4-3 fuel gauge resistance setting.
* If the problem is not resolved after following the steps shown above, please contact your loval distributor for assistance.
wh041ba02a(P6-6)
