Thermalright Macho Rev. A BW CPU Cooler Instruction manual
Below you will find brief information for CPU Cooler Macho Rev. A BW. The Macho Rev. A BW is a CPU cooler that is designed to provide excellent cooling performance for your computer. It features a large heatsink with six heatpipes and a 140mm fan. The cooler is compatible with a variety of Intel and AMD sockets, making it a good choice for a wide range of systems. The cooler is also very quiet, making it a good choice for those who want a quiet computer.
PDF
Download
Document
Advertisement
Advertisement
Thermalright NWWWWWWWNNW Macho Rev. A (BW) Macho Rev. A [BW] REECE ELE <> X] el x | <= mm Thermalright Macho Rev.A [BW] Intel 775/1150/1155/1156/1366 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Anti-Vibration Pads в и Mounting Plate “— Screw Nut Intel Washer — (small) = *— Metal Back Plate *C M3 L10 Screw Mylar 1 mm Thermalright Component 1 Chill Factor | | Era ECO © acho Heatsink Body x1 | @) Anchoring Mount x1 | E) Metal Back Plate x1 @ Mounting Plate x1 @ screw Nut x4 LoA201 Type B @ 13 L10 Screw x5 @ 13 L6 Screw x7 ©) Intel Washer (small) x4 {® AMD Washer (big) x4 @ Anti-Vibration Pad x4 | (I) Backplate cap x1 ® Fan Clip x2 @ Thema paste x1 E Screw driver x1 0 1-147 1 @ Mylar x1 The Ultimate Cooling Solutions! www thermalright.com 2 Installation Instructions: Step 1: Step 1 : Part Installation Take out Macho cooler from the paper box. Remove the TY-147 from the cooler by pulling the Fan Clips upwards in order to give room for ease of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them. Apply Anti-Vibration Padding to 4 comers on the Heatsink Body. Step 2: Step 2 : Backplate Installation Choose the platform (7 75/11501155/1156/1366) you are in use. Make four M3L10 Screw Pillars go through the Metal Back Plate and the Mylar film from bottom towards top.And then place the Metal Back Plate on the table. Fut the four Washers (for Intel) around the Screw Pillars. Step 3 : 775 backplate cap Step 4 : Place the motherboard on top of the Back Mote: When installing on a 775 platform, please | Flate. See the four Screw Pillars go through the first insert the Back Plate Cap into the opening on | four holes around the processor socket Cap the the Back plate, make sure you have the Cap facing | four Screw Pillars with the four Screw Nuts Make downwards. (Only for 775). sure the side with a washer is facing the Back Plate. ma Thermalright Step 5: Flace the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Pillars, Step 6: Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 7: Step 8: Step 7: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two M3LE6 Screws to Secure the Mounting Plate. Step 8: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the M3LE Screw undemeath the cooler. = == Ш и A e Step 9 : Fan Installation Place the included TY-147 onto the Heatsink Body. And then secure it with the Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-147. Step 10: Step 10 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 4 Macho Rev.A [BW] Intel 2011 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com — Fan Clip Macho Heatsink Body — M3 L6 Screw — a“ = Anchoring Mo unt—_ Anti-Vibration Pads Mounting Flate 5 mm Thermalright Component O © Chill Factor || Era ECO © acho Heatsink Body x1 | @) Anchoring Mount x1 | E) Metal Back Plate x1 @ Mounting Plate x1 @ screw Nut x4 LoA201 Type B @ 13 L10 Screw x5 @ 13 L6 Screw x7 ©) Intel Washer (small) x4 {® AMD Washer (big) x4 @ Anti-Vibration Pad x4 | (I) Backplate cap x1 ® Fan Clip x2 @ Thema paste x1 E Screw driver x1 0 1-147 1 @ Mylar x1 The Ultimate Cooling Solutions! www thermalright.com 6 Installation Instructions: Step 1: aL [Ye E = E A === = ===> === == === + FE = >. Sn NU 1 Step 1 : Part Installation Take out Macho cooler from the paper box. Remove the TY-147 from the cooler by pulling the Fan Clips upwards in order to give room for ease of installabon. And leave the fan clips on the Heatsink Body. Do not remove them. Apply Anti-Vibration Padding to 4 comers on the Heatsink Body. Step 2: Step 2 : Screw Pillar Installation Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four holes around the processor socket Cap the four Screw Pillars with the four Screw Nuts. Make sure the side with a washer is facing the Back Plate. Step 3: Step 3: Anchonng Mount Installation Place the Anchoring Mount on the Screw Muts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Pillars. ma Thermalright Step 4: Step 4 © Applying Thermal Paste Apply the Thermal Faste to the base of the Heatsink and the surface of the CPU evenly. Step 5: Step 5: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two M3LE Screws to Secure the Mounting Plate. Step 6: Step 6: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the M3LE Screw undemeath the cooler. Step 8: Step 7 : Fan Installation Place the included TY-147 onto the Heatsink Body. And then secure it with the Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-147. Step 8: Installation completed Flug in the fan connector to the CFU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 8 Macho Rev.A [BW] AM2/AM2+/AM3/AM3+/FM1 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com —— Fan Cli Macho Heatsink Body — ны ° M3 L6 Screw—, 5 Anchoring Mount —, D ee Anti-Vibration Pads Mounting Plate и = en Nut 1 “— Metal Back Plate “— M3 L10 Screw Backplate cap 9 mm Thermalright Component O © Chill Factor || Era ECO © acho Heatsink Body x1 | @) Anchoring Mount x1 | E) Metal Back Plate x1 @ Mounting Plate x1 @ screw Nut x4 LoA201 Type B @ 13 L10 Screw x5 @ 13 L6 Screw x7 ©) Intel Washer (small) x4 {® AMD Washer (big) x4 @ Anti-Vibration Pad x4 | (I) Backplate cap x1 ® Fan Clip x2 @ Thema paste x1 E Screw driver x1 0 1-147 1 @ Mylar x1 The Ultimate Cooling Solutions! www thermalright.com 10 11 Installation Instructions: Step 1: Le A === Нео LE ——— ee = ZZ = 4 = E Na Rl Step 1 : Part Installation Take out Macho cooler from the paper box. Remove the TY-147 from the cooler by pulling the Fan Clips upwards in order to give room for ease of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them. Apply Anti-Vibration Padding to 4 comers on the Heatsink Body. Step 2: Step 2 : Backplate Installation Choose the platform (AMD) you are in usa. Make four M3L10 Screw Pillars go through the Metal Back Plate and the Mylar film from bottom towards top. And then place the Metal Back Plate on the table. Put the four Washers (for AMD) around the Screw Pillars. Step 3 : Backplate cap Mote: When installing on a 939 platform, please first insert the Back Plate Cap into the opening on the Back plate, make sure you have the Cap facing dowmwards. (Only for 939). Step 4 : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four holes around the processor socket Cap the four Screw Pillars with the four Screw Nuts Make sure the side with a washer is facing the Back Plate. ma Thermalright Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Pillars, Step 6: Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 7: TT ot | Step 8: Step 7: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two M3LE6 Screws to Secure the Mounting Plate. Step 8: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the M3LE Screw undemeath the cooler. Step 9: Step 10: Step 9 : Fan Installation Place the included TY¥-147 onto the Heatsink Body. And then secure it with the Fan Clips. by pulling the Fan Clips to place the four ends at the four holes on the TY-147 . Step 10 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 12 Macho Rev.A [BW] Intel 775/1150/1155/1156/1366 Explosionszeichnung Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.themalright.com verfügbar sind. Lüfterklammer Macho Kühlkörper — M3 L6 Schraube — Montagerahmen a Anti-Vibrationpad Befestigungsplatte x Rändelschraube = A = a Intel eae be == > ==" Unterlegscheibe — — = = (klein) = = 1 “— Multi Plattform Backplate X— M3 L10 Schraube Mylar 13 mm Thermalright Komponenten Chill Factor Mrs" 28 O macho Kuhikorper 1 O Nontagerahmen x1 | @ Multi Plattform Backplate O Befestigungsplatte 1 © Rándelschraube x4 O Adaplerschrqube x4 @ 3.10 Schraube x5 | @ M3L6 Schraube x7 | O) (Mein xa Pe O (oro) | @) Anti-vibrationspad x4 | @ Backplateeinsatz x1 ® Lufterklammer x2 © Warmeleitpaste x1 ® Schraubendreher x1 B 1-147 x1 UY Leitschutzfolie x1 The Ultimate Cooling Solutions! www thermalright.com 14 15 Installationsanleitung: Schritt 1: Machdem Sie den Macho Kühler aus der Verpackung genommen haben demontieren Sie zunächst den Lüfter, um die Installation zu vereinfachen. Belassen Sie hierbei die Lüfterkammem am Kühlkörper - entfernen Sie diese nicht. Bingen Sie die vier selbstklebenden Anti-Vibrationspads an den Ecken des Kühlkôrpers an. Schritt 2: Achten Sie auf die fir die entsprechenden Intel Sockel (775/1150/1155/1156/1 366) vorgesehene Bohrungen in der Multi Platiform Backplate. Fúhren Sie die vier M3L10 Schrauben jeweils von unten durch die Backplate und die mitgelieferte Leitschutzfolie und legen dann die Backplate auf den Tisch. Legen Sie die vier Unterlegscheiben (für Intel) Ober die hervorstehenden Gewinde. Schritt 3: Schritt 4: Beachten Sie. Platzieren Sie das Mainboard von oben auf die Bei Verwendung einer Intel Sockel /75 Plattform Backplate, 50 dass die hervorstehenden setzen Sie zuerst den Backplateeinsatz in die Schraubengewinde durch die Löcher um den quadratische Öffnung der Backplate ein. Gehen Prozessorsockel gehen. Schrauben Sie die Sie sicher, dass der Aufsatz nach unten zeigt. beiliegenden Rándelschrauben auf die vier Schraubengewinde. Achten Sie dabei darauf, dass die Seite mit der Unterdegscheibe zur Backplate Zeigt. ma Thermalright Schritt 5: T Setzen Sie den Montagerahmen auf die Rändelschrauben, Verwenden Sie die vier M3L6 Schrauben, um den Montagerahmen auf den Rändelschrauben zu befestigen. Tragen Sie eine hauchdúnne Schicht \Värmeleitpaste auf der Oberflâche der CPU und auf der Unterseite des Kühlers auf, Schritt 7: Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte durch den Kühlkörper und benutzen die beiden M3LE Schrauben, um die Befestigungsplatte zu befestigen. Schritt 8: Führen Sie den mitgelieferten Schraubendreher durch das Loch in der Mitte des Kühlkörpers, um leichter Zugang zu den M3L6 Schrauben unterhalb des Kühlers zu erhalten. Schritt 9: Schritt 10: Positionieren Sie den mitgelieferten TY-147 auf die Kihlerseite mit den bereits angebrachten AntiVibrationspads. Nun sichern Sie den Lúfter mit den Lifterklammem, indem Sie diese über den Lüfterrahmen klappen und die spitzwinkeligen Ecken in die Montagelöcher des Lifters einrasten lassen. Verbinden Sie den Lüfterstecker mit dem CPU PWM Lüfteranschluss auf dem Mainboard. Die Installation ist nun abgeschlossen. Bitte prüfen Sie die ordnungsgemäße Funktion vor Inbetiebnahme Ihres PC. The Ultimate Cooling Solutions! www.thermalright.com 16 Macho Rev.A [BW] Intel 2011 Explosionszeichnung Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.thermalright.com verfigbar sind. Macho Kühlkörper — M3 L6 Schraub E T Montagerahmen —, Anti-Vibrationspad Befestigungsplatte 17 mm Thermalright Component Chill Factor Mrs" 28 O macho Kuhikorper 1 O Befestigungsplatte 1 © Montagerahmen x1 © Rándelschraube x4 © Multi Plattform Backplate O LGA2011 Type В Adapterschraube x4 O M3 L10 Schraube x5 AMD Unterlegscheibe D (gro) x4 O M3 L6 Schraube x7 @ Anti-vibrationspad x4 Intel Unterlegscheibe © (klein) x4 PP Backplateeinsatz x1 ® Lüfterklammer x2 D 147 x1 © Warmeleitpaste =1 UY Leitschutzfolie x1 15, Schraubendreher 1 The Ultimate Cooling Solutions! www.thermalright.com 18 19 Installationsanleitung: Schritt 1: ED EAP ei ZZ“ pa 4 те Re EZ еНЕ IA. a. 5 = a === = еее = == — ZZ = = = Ee e € 22 + —=—— = == = un a к, CA CA se Nachdem Sie den Macho Kühler aus der Verpackung genommen haben demontieren Sie zunächst den Lifter, um die Installation zu vereinfachen. Belassen Sie hierbei die Lifterdammem am Kühlkörper - entfernen Sie diese nicht. Bringen Sie die wer selbstidebenden Anti-vibrationspads an den Ecken des Kühlkörpers an. Schritt 2: Schrauben Sie die vier LGA2011 Type B Adapterschrauben in die Gewinde des Montagerahmens, der sich um den Prozessorsockel befindet. Schritt 3: Setzen Sie den Montagerahmen auf die Rändelschrauben. Verwenden Sie die vier M3L6 Schraubenum den Montagerahmen auf den Rándelschrauben zu befestigen. ma Thermalright Schritt 4: Tragen Sie eine hauchdlnne Schicht Wärmeleitpaste auf der Oberfläche der CPU und auf der Unterseite des Kühlers auf, Schritt 5: Schritt 6: or А: Lu и EZ = =— ==] = A 7 o = = at = = fr = Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie den mitgelieferten Führen Sie anschließend die Befestigungsplatte Schraubendreher durch das durch den Kühlkörper und benutzen die | Loch in der Mitte des beideM3L6 Schrauben, um die Befestigungsplatte | Kühlkörpers, um leichter Zhefestigen. Zugang zu den M3L6 Schrauben unterhalb des Kühlers zu erhalten, Schritt 6: Schritt 7: 2 Positionieren Sie den mitgelieferten Ty-147 auf Verbinden Sie den Lüfterstecker mit dem die Kühlerseite mit den bereits angebrachten CPU PWM Lüfteranschluss auf dem Mainboard. AntiVibrationspads. Nun sichern Sie den Lüfter Die Installation ist nun abgeschlossen. Bitte mit den Lüfterdammem, indem Sie prüfen Sie die ordnungsgemäße Funktion vor diese über den Lüfterrahmen klappen und die Inbetiebnahme Ihres PC. sprtzwinkeligen Ecken in die Montagelöcher des Lüfters einrasten lassen. The Ultimate Cooling Solutions! www.thermalright.com 20 Macho Rev.A [BW] AM2/AM2+/AM3/AM3+/FM1 Explosionszeichnung Wichtig!Bitte prûfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.thermalright.comverfügbar sind. — Lüfterklammer Macho Kühlkörper — M3 L6 Schraube Montagerahmen — T A Tes Anti-Vibration Pads Befestigungsplatte chraube AMD Unterlegscheibe — = (groß) É 3 1 “Multi Platform Backplate “— M3 L10 Schraube Backplateeinsatz 21 mm Thermalright Component Chill Factor Mrs" 28 O macho Kuhikorper 1 O Befestigungsplatte 1 © Montagerahmen x1 © Rándelschraube x4 © Multi Plattform Backplate O LGA2011 Type В Adapterschraube x4 O M3 L10 Schraube x5 AMD Unterlegscheibe D (gro) x4 O M3 L6 Schraube x7 @ Anti-vibrationspad x4 Intel Unterlegscheibe © (klein) x4 PP Backplateeinsatz x1 ® Lüfterklammer x2 D 147 x1 © Warmeleitpaste =1 UY Leitschutzfolie x1 15, Schraubendreher 1 The Ultimate Cooling Solutions! www.thermalright.com 22 23 Installationsanleitung: Schritt 1: | r TIN CC —— oF = — =, FL ZZ | | I LUI ANO = АННАН KA N A I \ 1 € | 7 a = E LY A A Machdem Sie den Macho Kühler aus der Verpackung genommen haben demontieren Sie zunächst den Lüfter, um die Installation zu vereinfachen. Belassen Sie hierbei die Lüfterklammenm am Kühlkörper - entfermen Sie diese nicht. Bringen Sie die ver selbstidebenden Anti-vibrationspads an den Ecken des Kühlkörpers an. Schritt 2: Achten Sie auf die für den AMD Sockel vorgesehene Bohrungen in der Multi Plattform Backplate. Führen Sie die vier M3L10 Schrauben jeweils von unten durch die Backplate und die mitgelieferte Leitschutzfolie und legen dann die Backplate auf den Tisch. Legen Sie die vier Unterlegscheiben (für AMD) Ober die hervorstehenden Gewinde. Schritt 3: Schritt 4: + Bei Verwendung einer AMD Sockel 939 Plattform Platzieren Sie das Mainboard von oben auf die setzen Sie zuerst den Backplateeinsatz in die Backplate, so dass die hervorstehenden quadratische Óffnung der Backplate ein. Gehen Schraubengewinde durch die Löcher um den Sie sicher, dass der Aufsatz nach unten zeigt. Prozessorsockel gehen. Schrauben Sie die beilisgenden Rändelschrauben auf die vier Schraubengewinde. Achten Sie dabei darauf, dass die Seite mit der Unterlegscheibe zur Backplate zeigt, ma Thermalright Schritt 6: Schritt 5: Setzen Sie den Montagerahmen auf die Tragen Sie eine hauchdúnne Schicht Rändelschrauben. Verwenden Sie die vier M3L6 Wärmeleitpaste auf der Oberfläche der CPU und Schrauben, um den Montagerahmen auf den auf der Unterseite des Kühlers auf. Rándelschrauben zu befestigen. Schritt 7: Schritt 6: Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte Schraubendreher durch das durch den Kühlkörper und benutzen die beiden Loch in der Mitte des M3L6 Schrauben, um die Befestigungsplatte zu Kühlkörpers, um leichter befestigen. Zugang zu den M3L6 Schrauben unterhalb des Kühlers zu erhalten, Schritt 9: Schritt 10: pre gd Positionieren Sie den mitgelieferten 120mm auf Verbinden Sie den Lüfterstecker mit dem die Kühlerseite mit den bereits angebrachten CPU PWM Lüfteranschluss auf dem Mainboard. AntiVibrationspads. Nun sichern Sie den Lüfter Die Installation ist nun abgeschlossen. Bitte mit den Lôfterdammem, indem Sie prüfen Sie die ordnungsgemäße Funktion vor diese über den Lüfterrahmen klappen und die Inbetriebnahme Ihres PC. spitzwinkeligen Ecken in die Montagelöcher des Lüfters einrasten lassen. The Ultimate Cooling Solutions! www.thermalright.com 24 Macho Rev.A [BW] Technical Spec Heatsink Specifications: Dimension: Length 140mm x Width 102mm x Height 162mm Weight: 710g Heatpipe: 6mm heatpipe*6 units Copper Base: C1100 Pure copper nickel plated Fan Specification: Dimension: L152mm x H140mm x W26.5m Weight: 160g Fan speed: 900~1300RPM (4-Pin PWM) Fan noise: 1/-21dBA MAX (4-Pin PWM) Airflow: 28.3~73.6CFM MAX Connector: 4 Pin (PWM Fan connector) 25 mm Thermalright Macho Rev.A [BW] Technische Spezifikationen Kühlkörper Spezifikationen: Maße (mm): Länge 140 x Breite 102 x Höhe 162 Gewicht: 710 g Heatpipe: 6 mm Heatpipe * 6 Stick Kupfer Grundplatte: C1100 reines Kupfer vernickelt Liifter Spezifikationen: Malte (mm): L152 x H140 x B26,5 Gewicht: 160 g Drehzahl: 900~1300 U/min (4-Pin PWM) Lautstärke: 1/-21 dBA max. (4-Pin PWM) Fördermenge: 48,08-125,04 mh max. Anschluss: 4 Pin (PWM Lüfteranschluss) The Ultimate Cooling Solutions! www.thermalright.com 26 = = == — == == == === === == === === 2 eH EH ii 24, HH}1 eR | O LALALA I CEE Cr Ш — a о Е Е = o — a a = Sa == = @ © © ds — = = es Es === © © © a a o o ek a A Cy D (р р To 7 Y = @ © © — = т! 140 — = = — = © © © Ч? PE бр бр 7 7 (== = v — — = | ¿OL = o < > @ oc . = U ГО = mm Thermalright 27 Macho Rev.A [BW] Awards EUITOR'S CHOICE Hi — E GOLD AWARD = [I TT Ey BP FE, Preis-Leistung Y god =) bu J xtreme Preis/Léistung À hardware jala Tes) ws = |v - The Ultimate Cooling Solutions! www.thermalright.con 28 The Ultimate Cooling Solutions! um Thermalright www.thermalright.com TEL: +886-2-8663-6630 FAX: +886-2-8663-6645 EMAIL: [email protected] ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 6mm heatpipe * 6 units
- 140mm fan
- Large heatsink
- Quiet operation
- Compatible with Intel and AMD sockets
Frequently asked questions
The Macho Rev. A BW is the same as the Macho Rev. A, but it has a black finish.
The fan is 140mm in diameter.
The maximum noise level of the fan is 21 dBA.
The maximum airflow of the fan is 73.6 CFM.
The cooler supports Intel sockets 775, 1150, 1155, 1156, 1366, 2011 and AMD sockets AM2, AM2+, AM3, AM3+, FM1.
The weight of the cooler is 710g.