Table of Contents Welcome Page 2 Before you start

Table of Contents Welcome Page 2 Before you start
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Table of Contents
Welcome
Before you start
Page 2
Page 2
Tutorial Guide
I. Make Disc-to-Disc Copies
II. Make Hard Drive (HDD) to Disc Copies
III. Select the Duplication Speed
IV. Select the Master Reading Source
V. Load Master Disc onto the Hard Drive
VI. Rename Existing HDD Partition Name
VII. Delete HDD Partitions
VIII. Change SETUP settings
IX. Audio CD Editing
X. Account Management Feature
XI. Duplication Mode
XII. Using AUTOSTART Feature
XIII. Using the USB Option
Menu Overview
1. Copy
2. Print
3. Advanced Copy Options
52
4. Image
5. Audio
6. SETUP
7. Utilities
8. SHUTDOWN
9. Autocopy
Troubleshooting
Load Default Settings
-1-
Page 4
Page 7
Page 14
Page 17
Page 20
Page 23
Page 26
Page 39
Page 30
Page 40
Page 45
Page 49
Page 51
Page 52
Page 52
Page
Page 52
Page 53
Page 53
Page 55
Page 57
Page 57
Page 60
Welcome!
Thank you for buying this Disc Makers duplicator. The Reflex DVD
and CD duplicator will make it easier than ever to duplicate vast
quantities of discs. This manual contains detailed information
about using all the features in your stand-alone Reflex duplicator.
******************************************************
Before you start:
Before you start using this duplicator, please read the following to
ensure proper operation:
1. DVD Duplication Limitations:
This duplicator, it will not copy any DVD that has Copy
Protection encoded inside. DVDs you purchase or rent from a
store will be Copy Protected.
In addition to the copy protection limitation, the duplicator
will only copy a DVD-5 format (4.7GB) disc to DVD-5 format
(4.7GB) recordable DVD media. If your duplicator has double
layer capability, you can copy a DVD-9 format (8.5GB) disc to
DVD-9 format (8.5GB) recordable DVD media. You cannot
duplicate a DVD5 format disc to a DVD9 format recordable
media or vice versa.
2. Temperature Warning:
If the duplicator was stored in a location where the
temperature dropped below 32ðF (0ðC) within the past 24
hours, please leave the duplicator in a warm room with
temperatures at least 65ðF (19ðC) for 4 hours prior to
-2-
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
powering it on for the first time. Failure to do so may cause
irreparable harm and prevent the duplicator from functioning.
3. Maintenance:
It is very important to operate and keep the duplicator in a
dust free, clean environment since dust is the number 1 killer
for CD/DVD recording devices. Failure to do so may severely
damage your duplicator. We strongly suggest you place an
Air Cleaner next to the duplicator and constantly use the Air
Duster (Can Air) to clear off any dust on the surface of the
duplicator.
Do not try to use Air Duster to clean the
duplicator while the reader/writer trays are open.
In doing so, you may inadvertently blow dust
into the recording device and damage the
recording device.
4. Proper Shutdown:
To avoid possible system failures the duplicator must be
shutdown properly. To shutdown the duplicator, use the UP or
DOWN arrow keys or the ‘Shutdown“ hot key and follow
instructions on the screen. Turning off your duplicator without
performing this function will increase the risk of damaging
your duplicator.
-3-
-4-
t
Reflex Duplicator Manual
t
Drive 1
Selected!
Tutorial Guide:
I.
Make Disc-to-Disc Copies
Reflex Duplicator Manual
Port 1.0
2. Go back to 1.COPY Menu.
This process will copy your master disc to several blank discs
simultaneously.
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
Disc Makers
1. COPY
a. Use UP or DOWN arrow button to navigate to the
following screen:
Disc Makers
1. COPY
1.12
1.12
3. Start the Copy Process.
1. Make sure the Master Reading Source is set to the
READER.
It is very important to make sure that your current Master
Reading Source is the top tray in order to avoid
unnecessary error messages. To check the Master Reading
Source, please do the following:
a. Press the Source hot key under the display to navigate
to the following screen.
a. Insert your master disc and your blank discs into the
corresponding tray(s) and press ENT button to enter
COPY menu. You will see the duplicator mode menu like
below:
Duplication Mode:
On The Fly
b. Press ENT
Hard Drive Port0.0
Preparing…
Waiting For Master
b. Use the bottom arrow key to scroll to Drive 1.
Drive 1
c.
Port 1.0
Copying…
0
1%
Press ENT to submit your selection.
-5-
-6-
10M
1M
t
Reflex Duplicator Manual
t
If you happen to have any failed discs (bad copy),
the failed disc(s) will not be ejected automatically.
You need to manually eject them and throw them
away if they are write once recordable disc(s).
Once the duplication run is completed, the successful copies will
be ejected and you shall see the following screen:
For detail information, please review Tutorial Guide XII:
Introduction to Duplication Mode.
Pass 1 Fail 0 ( 1)
Waiting For Blanks
c. Simply insert more blank media if more copies are
needed or press ESC to return to 1.Copy
Reflex Duplicator Manual
Tutorial Guide:
II. Make Hard Drive(HDD)-to-Disc Copies
Copying from the Hard Drive is the best way to make copies!
There are 3 benefits to copying from the Hard Drive:
It is normal to see the progress indicator stays at 010% and 100% for approximately 30 seconds for
CD duplication and up to 1 minute for DVD
duplication. This is caused by the initializing and
finalizing stage.
i.
Performance - Duplicating from the Hard Drive will be
able to boost the DVD duplication speed.
ii.
Stability - Duplicating from Hard Drive will stabilize the
duplication process compared to the Disc to Disc
process.
iii.
Convenience - With your master discs stored inside the
Hard Drive, you can have access to each one easily.
There is no need to carry your master discs; they are all
stored inside the duplicator.
PASS 7 FAIL 0(
7)O
Waiting for Blanks
-
“PASS 7” indicates that you’ve
just made 7 successful copies.
-
“FAIL 0” indicates that you
have no failure in this run.
-
“7” indicates that you’ve
successfully copied 7 copies so
far.
-7-
Your built-in Hard Drive will be divided into a number of
partitions. Each partition will hold ONE and ONLY ONE
master disc regardless of the capacity of your master disc.
-8-
t
Reflex Duplicator Manual
t
The number of partitions is determined by dividing your Hard
Driveís total capacity by 1GB for CD format, 5GB for DVD-5
format or 9GB for DVD-9 format (Double Layer) and
subtracting one partition for system use.
b. Scroll up to this screen:
Hard Drive
Port 0.0
Hitachi
HDT725025UL
The following steps will show you how to load your master
disc into the installed Hard Drive as a disc image and copy the
stored disc image into several blank discs. This process is
recommended for large volume production.
c.
1.
a.
Press Source button below the display and you
shall see the following:
Drive 1
Port 1.0
Optiarc DVD R AD5170A
-9-
Port 0.0
d. The screen should go back to:
1.12
Make sure the Master Reading Source is set to the Hard
Drive.
It is very important to make sure the Master Reading Source
is set to the Hard Drive in order to avoid unnecessary error
messages. To check the Master Reading Source, please do
the following:
Press ENT
Hard Drive
Selected!
How to make copies from the Hard Drive?
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
DISCMAKERS
1.COPY
Reflex Duplicator Manual
Discmakers
1. Copy
2.
1.12
Copying From the Hard Drive
a. Insert desired number of blank media
DISCMAKERS
1. Copy
- 10 -
1.12
t
Reflex Duplicator Manual
b. Press ENT and select the partition you want to burn.
Choose Partition:
[Name] Data
74M
t
Reflex Duplicator Manual
If the WAITING FOR BLANKS screen is displayed
for more than 2 minutes, please check your Blank
Discs for quality.
d. Press ENT
c. Press ENT.
Preparing…
74M
Waiting for blanks
Please allow 5-10 seconds for the duplicator to detect your Hard
Drive partition and Blank Discs as well. After your Hard Drive
partition and Blank Discs have been recognized, then you shall
see the following screen:
Preparing…
7 Disc Detected Go?
The unit will Auto start the copying process if all
drives are loaded and detected. If all drives are
not loaded, you will need to press ENT.
By default, the “Auto Start“ setting is set to
“Auto“. For example, if your duplicator has
detected 3 blank discs and did not detect any
additional blank discs for 30 seconds, then the
duplication will be started automatically.
- 11 -
Preparing...
Please Wait
After 2 or 3 seconds of processing time, the following Copy
Progress Screen will appear.
Copying ...
2%
H
74M
3M
-
“74M” indicates the capacity of
the master disc.
-
“2%” indicates the current
progress of the duplication..
-
“H” indicates you are copying
from a Hard Drive Image.
It is normal to see the progress indicator stays at 010% and 100% for approximately 30 seconds for
CD duplication and up to 1 minute for DVD
duplication. This is caused by the initializing and
finalizing stages.
- 12 -
t
Reflex Duplicator Manual
Once the duplication run is completed, the good copies
will be ejected and you shall see the following screen:
PASS 7 FAIL 0(
7)O
Waiting for Blanks
-
“PASS 7” indicates that you’ve
just made 7 successful copies.
“FAIL 0” indicates that you
have no failure in this run.
“7” indicates that you’ve
successfully copied 7 discs.
t
Reflex Duplicator Manual
If you happen to have any failed discs (bad copy),
the failed disc(s) will not be ejected automatically.
You need to manually eject them and throw them
away if they are write once recordable disc(s).
NOTES
Next, refill more blank media to continue making more copies, or
you can press “ESC“ to terminate your project and go back to the
main menu.
If you enable the counter and specified a counter value for
your project and your project is completed, you shall see
the following screen:
21 Disc Copied
Press OK to Finish
If you see above message, you can press “ENT“ to go
back to main menu.
If you enabled the counter and the number of
discs you have inserted is more than what you
requested, you will receive a message regarding
you have inserted more discs than what you need.
You can continue to copy or you can eject the
extras.
- 13 -
- 14 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Tutorial Guide:
III.
DISCMAKERS
5. Setup
Select the Duplication Speed
This process will allow you to adjust the duplication speed
subject to your various needs.
2.
Blank Media Compatibility - When your media
compatibility is not good, lowering the duplication
speed is necessary to make good copies.
•
Poor Master Disc Quality - If your master disc
condition is not good, lowering the duplication
speed will reduce failure rates.
•
Duplication Quality - The lower the burn speed, the
higher the quality of your duplicates. When you have
time, it is a good choice to lower down the speed to
produce the best quality duplicates.
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
DISCMAKERS
1. COPY
1.
1.12
Navigate to Speed Selection Menu.
Press UP or DOWN arrow button to navigate to the
following screen.
- 15 -
Press “ENT“ and the first option will be:
Setup
1. Select Burn Speed
By default, the duplication speed will be set to the optimal
speed. However, under some circumstances, you might want
to lower the duplication speed. Those circumstances are as
follows:
•
1.12
3. Press ENT again to access Speed Selection Menu.
Then, you can press “ENT“ button to enter into Speed
Selection Menu.
You shall see the following:
Select Burn Speed:
CD to CD SPEED
•
•
•
•
4. Select Duplication Speed Type.
There are four types of recording speed:
CD to CD: Copy CD Disc to CD-R Discs directly. (On-TheFly)
DVD to DVD: Copy DVD Disc to DVD±R Discs directly.
(On-The-Fly)***
HDD to CD: Copy Hard Drive CD Image to CD-R Discs.
HDD to DVD: Copy Hard Drive DVD Image to DVD±R
Discs.
Depending on what type of duplication and your duplicator
restrictions, you need to select the correct type in order to
take effect. To select the recording speed types, you need
to press UP or DOWN button to adjust and press “ENT“
button to submit your selection.
- 16 -
t
***
Reflex Duplicator Manual
To ensure the duplication quality, for certain models, you
are not allowed to adjust the duplication speed for DVD to
DVD to greater than 6x duplication speed. To achieve
maximum duplication speed, you need to perform
duplication tasks from the Hard Drive. For detailed
instructions, please refer to “Tutorial Section II - Make Hard
Drive-to-Disc Copies.“
5.
Select Desired Duplication Speed.
Once you have submitted the duplication speed type, you
shall see the following:
You can press UP or DOWN button to select the desired
speed and then press “ENT“ to submit your speed selection.
Once your selection has been changed successfully,
you shall see the following screen for 2 seconds.
CD to CD Speed:
Adjusted to:
24x
Then you will be directed back to the Setup sub-menu:
Select Burn Speed
CD to CD Speed
7.
Reflex Duplicator Manual
Tutorial Guide:
IV.
Select the Master Reading Source
When you try to make a copy, you need to specify where the
master disc is. Is it in the Reader tray? Or is it an Image
inside the Hard Drive? This tutorial will show you how to
change the Master Reading Source to satisfy your needs.
The two copy methods are:
• Disc-to-Disc copy - This is the case when you would
normally make copies on the fly. You need to set the
“Reader“ as your Master Reading Source.
CD to CD Speed:
16x
6.
t
• Hard Drive-to-Disc copy (if Hard Drive installed) - If you
want to make copies from your Hard Drive Image, you
need to select the source as “Hard Drive“.
There are benefits to copy from Hard Drive:
i.
Performance - Duplicating form the Hard Drive will
be able to boost the DVD duplication speed to 8x
or above.
ii.
Stability - Duplicating from Hard Drive will stabilize
the duplication process compared to the Disc to
Disc duplicating.
iii.
Convenience - With your master discs stored inside
the Hard Drive, you can have access to each one
easily. There is no need to carry your master discs;
they are all stored inside the duplicator.
Press ESC twice to return to Main Menu
- 17 -
- 18 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
Then you will be directed back to the menu:
Disc Makers
1. COPY
1.
1.12
DISCMAKERS
1.Copy
Press “Source“ hot key to navigate to Select Source Menu.
Setup
5.2 Select Source
After loading your master disc to the Hard Drive,
please make sure to remove your master disc from
the Master Reading Tray. Failure to do so might
cause improper duplication.
NOTES
2.
Enter Source Selection Menu.
Press “ENT“ button to enter into Source Selection Menu.
You shall see the following:
Hard Drive Port 0.0
Hitachi HDT725025UL
Select Desired Master Reading Device.
You can press UP or DOWN button to select the desired
Master Reading Source. Then, you can press “ENT“ to
submit your Source Selection.
3.
1.12
Once your selection has been changed successfully, you
shall see the following screen for 2 seconds:
Hard Drive
Selected!
- 19 -
Port 0.0
- 20 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Tutorial Guide:
V.
Load Master Disc onto the Hard Drive
In order to copy from the Hard Drive, you are required to load
your master disc onto a hard drive partition.
The number of partitions is determined by dividing your Hard
Driveís total capacity by 1GB for CD format, 5GB for DVD-5
format or 9 GB for DVD-9 format (Double Layer) and subtracting
one partition for system use.
For example, if you have a 40GB Hard Drive, you can calculate
the number of DVD-5 format partitions by: 40 / 5 = 8. Since there
is 1 partition reserved for the system use, you will have 7
partitions to use.
To load your master disc onto a hard drive partition, please do
the following:
Load Partition [ 1/
Load->New Partition
16]
*The “1” indicates the number of partitions
you’ve already loaded into the Hard
Drive .
(Includes the Reserved Partition)
*The “16” indicates the total number of partitions
you can load to the Hard Drive.
c. Now, you have a choice to load your master disc
into a new (empty) partition or overwrite one of the
existing partitions if any exists. You can simple
press UP or DOWN arrow button to select your
partition and press “ENT“ to submit. You will see
the following:
LoadPartition[002/16]
Overwrite[name]
1.
Load your master disc onto the Hard Drive.
a. Press the “Load“ hot key or scroll to Image to
navigate to the following screen.
Select HDD as source
OK?
b. Press “ENT“ to enter Load Partition Menu and you
shall see the following:
d. Now, you can name the partition you are about to
load into the Hard Drive. To enter the name, you
need to use UP or DOWN button to select the
character and use “ENT“ or “ESC“ button to move
the cursor position and once youíve finished, move
the cursor to “OK“ and press “ENT“. For example,
if I want to name the partition of your master disc
as “FUN“. Then do the following:
Edit Partition Name
[x
] OK?
- 21 -
- 22 -
t
Reflex Duplicator Manual
t
Make sure the cursor is located at the first position:
i.
Press “DOWN“ button consecutively until “F“ is
displayed.
ii.
Press “ENT“ button once to move the cursor to the
next position.
iii.
Press “DOWN“ button consecutively until “U“ is
displayed.
iv.
Press “ENT“ button once to move the cursor to the
next position.
v.
Press “DOWN“ button consecutively until “N“ is
displayed.
vi.
Press “ENT“ button once to move the cursor to the
next position.
vii.
Now, we have the name “FUN“ displayed and
then, press “ENT“ consecutively until the cursor is
moved to “OK“.
viii.
Then, press “ENT“ once to submit your name
selection.
e. Now you shall see the following confirmation screen:
Load Partition?
[FUN
], OK?
f.
Press “ENT“ button to confirm. Once your master disc has
been recognized. The loading progress indicator will be
displayed and you shall see the following
- 23 -
Reflex Duplicator Manual
Loading ...
FUN
12%
420M
23M
*The “12%” indicates the percentage of data has
been loaded to the Hard Drive.
g. Once your master disc has been loaded completely, you
shall see the following:
Load Partition OK!
Press OK to Finish
Then, you can press “ENT“ button to go back to the
Image ñ Load Partition Menu.
Tutorial Guide:
VI.
Rename Existing Hard Drive Partition Name
When you load your master disc to a hard drive partition,
you are asked to give it a name. However, if you donít like
the name you entered before, you can rename it at anytime
afterwards. To rename your existing hard drive partition
name, please do the following:
1. Use UP or DOWN arrow button to navigate to the
following screen.
DISCMAKERS
3. Image
1.12
2. Press “ENT“ and use UP or DOWN arrow button to
navigate to the following screen
- 24 -
t
Reflex Duplicator Manual
Image
3.Rename Partition
3. Press “ENT“ to enter Rename Partition Menu and you
shall see the following:
Choose Partition:
[FUN
] Data 4M
4. Use UP or DOWN arrow button to find the desired
partition and then press “ENT“ to submit your selection
and you shall see the following confirmation screen:
Rename Partition
[FUN
] Data, OK?
5. Press “ENT“ once again to confirm it and you shall see
the following:
Rename Partition
[FUN
]OK?
6. Now, you can rename the partition youíve just selected.
t
Reflex Duplicator Manual
until you reached desired location:
Enter HDD Image Name
[FUN2
] OK
i. Press “DOWN“ button consecutively until “2“ is
displayed.
ii. Now, we have renamed the image name “FUN“ to
“FUN2“. So we can press “ENT“ consecutively until the
cursor is moved to “OK“.
iii. Then, press “ENT“ once to submit your name selection.
Once youíve done above, you shall see the following:
Partition [FUN2
Renamed!
Then, you will be directed back to HDD Image Setup
Menu.
Image
3.Rename Partition
NOTES
To enter the name, you need to use UP or DOWN
button to select the character and use “ENT“ or “ESC“
button to move the cursor position and once you
finished, move the cursor to “OK“ and press “ENT“. For
example, if I want to rename the image “FUN“ to
“FUN2“. Then do the following:
Move the cursor to the forth position by pressing “ENT“
- 25 -
]
- 26 -
t
Reflex Duplicator Manual
Tutorial Guide:
VII. Delete Existing Hard Drive Partition Permanently
If for some reason you would like to delete your existing
hard drive partition permanently, you can do the following:
1.
Use UP or DOWN arrow button to navigate to the
following screen.
Disc Makers
3. Image
2.
1.12
Press “ENT“ and use UP or DOWN arrow buttons to
navigate to the following screen:
Image
4. Delete Partition
t
Reflex Duplicator Manual
4. Use UP or DOWN arrow button to find the desired
partition and then press “ENT“ to submit your
selection and you shall see the following:
Delete Partition
[FUN
] DVD, OK?
5. Press “ENT“ to confirm and you shall see the following
for 2 seconds.
Partition [FUN
Deleted!
7. Then, you will be directed back to Hard Drive Setup
Menu.
Image
4. Delete Partition
NOTES
3.
Press “ENT“ to enter Delete Partition Menu and you
shall see the following:
Choose Partition
[FUN
] DVD
- 27 -
]
- 28 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Tutorial Guide:
Tutorial Guide
VIII.
Change the SETUP settings
Most of the internal settings and information is stored inside
the SETUP menu. To explore and modify them is simple.
Below is an example to modify the “Auto Start“ setting.
Please note that the default setup is set for optimal
performance of the duplicator, it is unnecessary to change if
you are satisfied with the outcome.
1. Use UP or DOWN arrow button to navigate to the
following screen.
DISCMAKERS
5.Setup
2.
Setup
10. Auto Start
5.
If you would like to modify more settings, then please
go back to step 3. Otherwise, press “ESC“ button to
bring you back to main menu.
DISCMAKERS
5. Setup
1.12
NOTES
Press “ENT“ and use the UP or DOWN arrow buttons
to navigate to the following screen:
Setup
10. Auto Start
3.
Press “ENT“ to enter Auto Start Setting Menu and you
shall see the following:
Auto Start
Auto
4.
Use UP or DOWN arrow button to modify the setting to
“Full“ and then press “ENT“ to submit your selection
and you shall see the following:
- 29 -
- 30 -
1.12
t
Reflex Duplicator Manual
Tutorial Guide:
IX.
t
1.
Audio CD Editing
Reflex Duplicator Manual
Going to the “Edit Audio Track“ menu
Use the UP or DOWN arrow button to navigate to the
following screen and press “ENT“.
This process will guide you to perform the Audio Track
Selection feature. This process will help you combine audio
tracks from various CDs into a single customized audio CD.
In order for the duplicator to do all those things, you need a
temporary storage location to hold your songs before the
duplicator can make it an audio CD. The following are the
choices you will have:
• Hard Drive (if a Hard Drive is Installed):
By choosing “Hard Drive“ as the temporary storage
location, you will be instructed to load all of your
favorite songs into the Hard Drive and after you have
selected all of your favorite songs, you will be
instructed to copy them onto a blank 80 min CD-R
media.
• Blank CD-R media:
By choosing “Blank CD-R“ as the temporary storage
location, you will be instructed to copy all of your
favorite songs into the blank CD-R youíve inserted
and after you have finished, you will be instructed to
finalize the CD-R disc.
When you turn on your duplicator, after it has booted up, you
will see the following screen:
DISCMAKERS
1. COPY
- 31 -
1.12
DISCMAKERS
4. Audio
2.
1.12
If your duplicator does not have a Hard Drive installed, skip
to Step 5. However, if your duplicator does have a Hard
Drive installed, you will see the following:
Edit Audio Tracks
Edit to Blank CD
At this point, you can press UP or DOWN arrow button to
select how you want to mix your audio tracks
Below are your options:
• Hard Drive(if a Hard Drive is Installed):
By choosing “Hard Drive“ as the temporary storage
location, you will be instructed to load all of your
favorite songs into the Hard Drive and after you have
selected all of your favorite songs, you will be
instructed to copy them onto a blank 80 min CD-R
media.
• Blank CD-R media:
By choosing “Blank CD-R“ as the temporary storage
location, you will be instructed to copy all of your
favorite songs into the blank CD-R youíve inserted
and after you have finished, you will be instructed to
finalize the CD-R disc.
- 32 -
t
3.
Reflex Duplicator Manual
Once you made your selection, you shall see the following:
Preparing...
Waiting for Master
OR
Preparing...
Waiting for a Blank
When you see above, please insert an audio CD that
contains your favorite track(s) in the Master Reading Tray
and a blank CD-R media into one of Writer Trays.
If either one of the ABOVE 2 screens is shown for
more than 2 minutes, please check your Master
Disc or Blank Discs for quality.
Please allow 5-10 seconds for the duplicator to detect your
Master Disc and Blank Discs as well. After your Master Disc
and Blank Discs have been recognized, then you shall see
the following screen:
Total: 0 Trk 0m: 0s
Track 1: 4m:31s
When you see above, you can press UP or DOWN arrow
button to display the information on each track of this audio
CD and press “ENT“ to select the track to be copied. Once
a track is selected, you shall see “*“ on the left of the track
number on the 2nd line. You will also be able to see the
total tracks and total playtime you have selected. Once you
have finished selecting the tracks you want to copy, you can
press UP or DOWN arrow button until you see “ARE YOU
DONE?“ on the 2nd line like screen following:
- 33 -
t
Reflex Duplicator Manual
Total 6 Trk 26m:17s
Are you done?
You can press “ENT“ button to submit your selection. You
will see the following:
Audio Editing
2%
1
09:19
“1” indicates that it is working on track #1.
“09:19” indicates that the track’s playback time.
If the capacity of total audio tracks you have
selected is more than your blank CD-R discís
capacity, you shall see the following two screens
flashing:
OVER BLANK DISC CAPA
Press OK to Continue
BLANK DISC CAPACITY
Press OK to Continue
If you see messages above, please press “ENT“ button to
continue.
Once the Copying process is complete, you shall see the
following screen:
Total 6 Trk 26m:17s
Finish Editing?
>
At this point, you have a choice to finalize it (mark the completion)
or insert another audio CD for more songs.
- 34 -
t
Reflex Duplicator Manual
If you choose to insert another audio CD for more songs, you
need to press DOWN arrow button until you see the following
screen:
Audio Editing…
2
Insert Next Master?>
t
Reflex Duplicator Manual
When the whole process completes, your mixed copy will be
ejected and you shall see the following:
Job Completed!
Press OK to Finish
Press ENT to return to the main menu:
Then, press “ENT“ button to continue. After that, your old master
disc will be ejected and you can insert another audio CD into the
Reading Tray. Please go back and follow the instruction on Step 3.
If you choose to finalize it, you need to press the DOWN arrow
button until you see the following screen:
DISCMAKERS
4. Audio
NOTES
Total 6 Trk 26m:17s
Finish Editing?
>
Then, press “ENT“ button to continue. You will see following
confirmation screen:
Total 6 Trk 26m:17s
Confirm to Finalize?
Press “ENT“ button again to confirm the finalization; it will copy
all tracks to the blank CD-R media you have inserted and finalize
it at the end. During the process, you shall see following progress
indicator:
Finalizing...
Please Wait
- 35 -
- 36 -
1.12
t
Reflex Duplicator Manual
Example of Editing Audio Tracks to Hard Drive
(For Duplicators with Hard Drive Installed):
t
Reflex Duplicator Manual
Total: 1 Trk 4m:49s
*Track 2: 4m:49s
We need to create a new Audio CD from 2 different Discs.
7. Use the UP or DOWN arrow button until you see “Track 4“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 4“ like following:
CD1: song 2, and song 4
CD2: song 3, song 4 and song 5
Total: 2 Trk 9m:47s
*Track 4: 4m:58s
1. Go to function 11. Edit Audio Track
DISCMAKERS
4.Audio
1.12
8. Use the UP or DOWN arrow button until you see following:
Total: 2 Trk 9m:47s
Are you done?
2. Press “ENT“ button.
Edit Audio Tracks
Edit to Blank CD
3. Use UP or DOWN arrow button to select “HDD“. Then press
“ENT“ button.
Edit Audio Tracks
Edit to HDD
4. Insert CD1 into the Master Reading Tray and a blank to Writer
Tray 1.
5. Wait until the following screen appears.
Total: 0 Trk 0m:00s
Track 1: 4m:03s
6. Use the UP or DOWN arrow button until you see “Track 2“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 2“ like following:
- 37 -
9. Press “ENT“ Once you submit your selection, you shall see
the following:
Audio Editing...
2
3%
04:58
10. Once the loading process is complete, you shall see the
following screen:
Audio Editing...
Finish Editing?
2
>
11. Since you have not done with your selections yet, you need to
press DOWN button once and you shall see following:
Total: 2 Trk 9m:47s
Insert Next Master?
12. Press “ENT“ button to continue and insert CD2 into the
- 38 -
t
Reflex Duplicator Manual
reader tray. When CD2 is inserted, wait until the following
screen appears.
Total: 2 Trk 9m:47s
Track 1: 4m:03s
13. Use the UP or DOWN arrow button until you see “Track 3“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 3“ like following:
Total: 3 Trk 14m:35s
*Track 3: 4m:47s
14. Use the UP or DOWN arrow button until you see “Track 4“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 4“ like following:
Total: 4 Trk 20m:01s
*Track 4: 5m:26s
15. Use the UP or DOWN arrow button until you see “Track 5“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 5“ like following:
Total: 5 Trk 24m:29s
*Track 5: 4m:27s
16. Use the UP or DOWN arrow button until you see following:
Total: 5 Trk 24m:29s
Are you done?
17. Press “ENT“ Once you submit your selection, you shall see
the following:
- 39 -
t
Reflex Duplicator Manual
Audio Editing...
3
5%
04:47
18. Once the loading process to the hard drive is complete, you
shall see following screen:
Audio Editing...
Finish Editing?
3
>
19. Since we have finished selecting all of our tracks. Press “ENT“
button to continue to finalize. You shall see the following
screen:
Audio Editing...
3
Confirm to Finalize?
20. Press “ENT“ button again to confirm the finalization and you
shall see the following screen:
Copying…
H
0/3
10%
79M
5M
21. When the whole process completes, your mixed copy will be
ejected and you shall see the following:
Job Completed!
Press OK to Finish
Then, you will be directed back to the main menu:
DISCMAKERS
4.Audio
- 40 -
1.12
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Tutorial Guide
X.
Introduction to Account Management Feature
This feature allows you, the administrator, to have the power to:
1. Create user accounts and passwords to prevent
unauthorized use of this duplicator.
2. Edit existing user account information, including
name and password.
3. Delete existing user account(s).
4. Enable/Disable this feature.
This feature is disabled by default. Prior to activating the
“account management feature, the duplicator recognizes all users
as the only activated user defined as the administrator. The predefined password for this function is “0000“.
By adding additional users, each individual user will have their
own settings and only have access to hard drive partitions they
loaded. No one else will have permission other than the
Administrator.
For example, if USER1 logged-in and loaded a master disc to the
hard drive partition (Partition A); if USER2 logs-in, USER2 will not
have access to any partition loaded by USER1, which includes
partition A.
To take advantage of this feature, follow the below instructions:
1. Change the Administrator password. Please refer
to Feature Overview “3. Edit User Info“ below for
more information.
2. Create a User Name and Password for every
authorized person on this duplicator. Please refer
to Feature Overview “2. Create User“ below for
- 41 -
- 42 -
t
Reflex Duplicator Manual
more information
3. Enable the Account Management feature by
turning ON the Password on Boot UP setting.
Please refer to Feature Overview “5. Password on
Bootup“ below for more information.
This duplicator comes with standard license, which
allows you to create up to 32 users.
t
Reflex Duplicator Manual
digit of your password and press “ENT“ button to submit
the current digit and you will be guided to select the next
digit. Repeat above steps until youíve selected all digits of
your password. After you have entered the password, you
need to press “ENT“ button on “OK“ to submit your
password.
Once your password is validated, you will be guided to
the main Manage Accounts screen like below:
Account Management Feature Overview:
To access the account management feature, you need to perform
the following tasks:
When you turn on the duplicator, you shall see following:
DISCMAKERS
1. Copy
1.12
Press UP or DOWN Button Consecutively until you see
following:
DISCMAKERS
6. Utilities
1.12
Manage Accounts
1. View User
There are five menus in the Manage Accounts:
1. View User
Manage Accounts
1. View User
This menu allows you to view current existing user
accounts.
Press “ENT“ and use the UP or DOWN arrow keys until
you see the following:
Utilities
7. Manage Accounts
Press “ENT“ button once. You will be asked for the
Administratorís Password.
Enter PWD
[XXXX] OK
(Admin)
By default, the Administratorís Password is “0000“. To
enter that, press UP or DOWN button to select the first
- 43 -
- User “Admin“ is the administrative account.
It will always be there.
Press “ENT“ button to enter into this menu and press
“ESC“ button to go back to the main menu or cancel the
current selection.
2. Create User
Manage Accounts
2. Create User
This menu allows you to create additional user accounts.
- 44 -
t
Reflex Duplicator Manual
t
Each user has their own settings and hard drive partitions.
During this process, you will be prompted to enter a new
user name and user password for a new account.
Manage Accounts
4. Delete User
- User name can consist of up to 8
alphanumeric letters or numbers.
- User password will consist of 4 numbers.
Press “ENT“ button to enter into this menu and press
“ESC“ button to go back to the main menu or cancel the
current selection.
This menu allows you to delete the existing user account.
During this process, you will be asked to select the
existing account to be removed.
- User “Admin“ is the administrative account;
you can NOT delete this account.
3. Edit User Info
Manage Accounts
3. Edit User Info
This menu allows you to change the existing user
accountís name and password. During this process, you
will be asked to select the existing account and then you
will be prompted to enter the new user name and new
user password for this account.
- User “Admin“ is the administrative account,
you can NOT change the user name for this
account, but you will be able to change the
password for this account.
- User name consists of up to 8 alphanumeric
letters or numbers.
-User password will consist of 4 numbers.
Press “ENT“ button to enter into this menu and press
“ESC“ button to go back to the main menu or cancel the
current selection.
4.
Reflex Duplicator Manual
Press “ENT“ button to enter into this menu and press
“ESC“ button to go back to the main menu or cancel the
current selection.
5.
Password on Bootup
Manage Accounts
5. Password on Bootup
This menu allows you to enable/disable account
management upon boot up. During this process, you will
be asked to select “ON“ or “OFF“ (enable/disable).
Press “ENT“ button to enter into this menu and press
“ESC“ button to go back to the main menu or cancel the
current selection.
Delete User
- 45 -
- 46 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
Tutorial Guide
XI.
Introduction to Duplication Mode
In order to achieve 8x or higher duplication performance;
there are 3 factors that need to be certified as 8x or higher
speed:
To simplify this process for anyone, we introduced a new
feature called “Load and Copy“ under the new category
“Duplication Mode“. This feature reduces the
“Duplication from Hard Drive“ process to a single step!
There are two features under “Duplication modes“:
1.
2.
3.
4.
Master Disc Reading Speed
Computer Controlling Speed
Recorder Writing Speed*
Blank Media Speed
*The recordable media must be certified 8x or higher
in order to have 8x or higher recorder writing speed.
If any or all of the above 4 factors fail to meet the 8x or up
higher certification, under any circumstances, you will
encounter bottleneck symptoms which will delay your
duplication time and reduce your duplication quality.
When making duplications directly from the master disc to
the blank disc; you often cannot maintain true 8x speed
throughout the duplication process. Unfortunately, due to
physical recordable DVD limitations, most DVD master
discs cannot be read at 8x or higher speeds continuously.
Often the reader will fall behind the burners and the whole
process will have to slow down.
In order to help this issue, first load the master disc into
the hard drive and make all duplications through the hard
drive. To duplicate form the Hard Drive, you need to load
your DVD master disc into a Hard Drive partition. Once
loaded, make copies from the Hard Drive partition as you
would from the master disc. This process can be a little
complicated and requires certain knowledge of the
duplicator in order to operate.
- 47 -
On the Fly:
This mode instructs the duplicator to copy directly
from the master disc. The duplicator performs
simultaneous read and write operations without
any delays.
Advantage:
Ideal for small quantity quick duplication.
Disadvantage:
Requires a master disc for each and every run.
(Could be harmful for the master disc)
Maximum DVD duplication speed is typically
limited to 4x or 6x.
Requires the master disc to be in excellent
condition for error free duplication.
Load and Copy:
This mode instructs the duplicator to load your
master disc into the built-in hard drive reserve
partition and make the requested quantity of
copies directly from the hard drive. The image will
remain stored in the reserve partition, available for
future duplications of the same project until you
perform this feature again with a new master.
Once a new master is used for Load and Copy, the
- 48 -
t
Reflex Duplicator Manual
new image will override the previous image and all
duplications from the reserve partition will be with
the new image.
Advantage:
Faster duplication in a long run.
(Un-Restricted DVD Duplication speed supported
by the duplication blank media)
Stable duplication.
Reliable duplication
Disadvantage:
The loading time may have an impact on overall
duplication time for small duplication jobs.
The master disc will be loaded to the reserve
partition in the Hard Drive temporarily until a new
master is loaded and overrides the previous image.
In comparing this duplication mode with the traditional
“Duplication from Hard Drive“ process, it offers the user more
simplicity. By selecting the “Load and Copy“ mode via one
simple touch, all the necessary tasks will be automated for you.
However, in bypassing the standard “Duplication from Hard
Drive“ process, you cannot use the Partition naming feature and
the image will only remain until itís overridden by using load and
copy from another master disc.
By default, the duplication mode is set to “Auto“. This will
prompt you to choose between one of the duplication
modes when you enter any of the following functions:
“Copy“, “Test“, “Test + Copy“, and “Copy + Compare“.
t
DISCMAKERS
1. Copy
Reflex Duplicator Manual
1.12
Press UP or DOWN Button Consecutively until you see following:
DISCMAKERS
5.Setup
1.12
Press “ENT“ and use the UP or DOWN arrows to navigate
to the following:
Setup
10. Duplication Mode
Press “ENT“ button once. You shall see following:
Duplication Mode:
Prompt
Press UP or DOWN Button Consecutively to select your
desired mode.
Duplication Mode:
Load and Copy
Press “ENT“ button once to submit your selection. You
shall see following:
Setup
9. Duplication Mode
Press “ESC“ Button once to go back to the main menu.
If you prefer not to be prompted each time you may set
your preference by following the instructions below.
When you turn on the duplicator, you shall see following:
- 49 -
- 50 -
t
Reflex Duplicator Manual
Tutorial Guide
XII.
t
Reflex Duplicator Manual
4. Use the UP or DOWN arrow button to modify the setting
and then press “ENT“ to submit your selection and you
shall see the following:
Using AUTOSTART
This hidden menu feature will be displayed when turned
on under “5. Setup“. The Autostart function allows you to
copy from Disc to Disc automatically without pressing
additional keys. The following tutorial will show you how
to activate this feature.
Setup
10.Auto start
4. Press “ESC“ once to go back to following screen:
DISCMAKERS
5. Setup
To Activate AUTOSTART feature:
1. Use the UP or DOWN arrow button to navigate to the
following screen.
DISCMAKERS
5. Setup
If you wish to deactivate this feature, please
follow the same steps above to turn this feature
off.
1.12
2. Press “ENT“ and use the UP or DOWN arrow keys to
navigate to the following:
Setup
10.Auto start
3. Press “ENT“ to enter the AUTOSTART Setting Menu and
you shall see the following:
Auto: This will automatically begin the burning process when
initiated.
Full: This will automatically begin the burning process only if all
drives are loaded.
Off:
You will need to accept each step of the burn process.
AUTOSTART:
Auto
- 51 -
1.12
- 52 -
t
Reflex Duplicator Manual
t
Reflex Duplicator Manual
You need to reboot your duplicator every time you
want to turn on/off the USB 2.0 connection.
Setup Guide
XIII.
Setup USB 2.0 connection
(This only applies if you have a USB connection installed)
For first time use Reflex 1
1. Turn your duplicator off if it is running.
2. Turn your computer off if it is running.
3. Set the USB2.0 switch to “ON“ at the back of your
duplicator.
4. Use the standard USB 2.0 cable to connect your computer
and your duplicator.
Every PC related product has compatibility issues.
Even though the USB connection has been thoroughly tested
before the unit was shipped out of the factory, thereís still a slight
chance that your PC/Mac computer is not compatible with the
units Firewire/USB connection. If that happens, please contact
your PC/Mac manufacture for possible configuration changes to
make it work or try another PC/Mac computer.
Menu Overview:
1.
5. Turn on your duplicator.
6. Turn on your computer.
7. After that, your computer will recognize a drive on the
duplicator that can be used as an external writer drive.
For first time use on Reflex 2 and above
1. With the unit powered on and press either arrow key
repeatedly to scroll through the options until the screen
display s ì7. Utillitiesî press Ent.
2. Scroll through the options until the screen displays ì9.
USB Connectionî press ENT. Use the up arrow key to
change the status to ìONî to activate the USB Option or
ìOFFî to disable.
3. The Reflex tower will now re-boot.
- 53 -
COPY
This menu will guide you to make CD/DVD copies. Before
you enter this menu to copy, please make sure you have
selected the correct Master Reading Source. For more
information, please refer to “Tutorial Guide I ñ Make Disc-toDisc Copies“ or “Tutorial Guide II ñ Make Hard Drive(HDD)to-Disc Copies“
2.
ADVANCED COPY OPTIONS
Test and Copy - This menu will guide you to perform the
simulation of copying process and if everything has passed during
the simulation, a real copying process will be performed. If thereís
an error encountered during the simulation, an error message will
be displayed and the copying process will not be initiated.
Copy and Compare - This menu will guide you to make
copies for you and after the copy process has been finished, it will
perform an additional comparison process automatically to
ensure data correctness.
Copy and Verify - This menu will guide you to perform Disc
Readalibility Check. This operation will check the readiblity of
your mater discs and the copied discs. The purpose to perform
this verify operation is to ensure all of your copies are readable.
- 54 -
t
Reflex Duplicator Manual
3.
IMAGE
Select Partition - Select a previously stored Hard Drive
Image to copy.
Load Partition - Load partitions to the duplicators Hard Drive
Rename Partition - Rename previously stored Hard Drive
images
Delete Partition - Delete images stored on your hard drive
Partition Info - View details of stored images such as name,
file size, and disc type.
Select Loading Drive - See drive port used to read masters
4.
AUDIO
Copy - This menu will guide you to edit audio tracks.
Before you enter this menu to copy, please make sure you
have selected the correct Master Reading Source. For
more information, please refer to “Tutorial Guide I - Make
Disc-to-Disc Copies“ or “Tutorial Guide II - Make Hard
Drive(HDD)-to-Disc Copies
Edit Track To:
Blank CD - create an audio compilation disc
Hard Drive - create an audio compilation hard
drive image.
5.
SETUP
Select Burn Speed - This menu will guide you to adjust
the duplication speed on various duplication modes. For
more information, please refer to “Tutorial Guide III Select the Duplication Speed“
Select Source - This menu will guide you to set the
Master Reading Source. For more information, please
refer to “Tutorial IV - Select the Master Reading Source“
Read Skip Error - Normally, when the duplicator
encountered a reading error while reading your master
disc, all the duplication will be aborted and all the
recordable media will be ruined. However, if you believe
- 55 -
t
Reflex Duplicator Manual
that your master disc has a small, insignificant error due to
physical damages, you can enable the setting to allow the
duplicator to skip any read error* it has encountered.
CD Writing Mode - This setting will allow you to select
which mode you would like to duplicate a CD. There are
two different modes, “Disc at Once“ and “Track at
Once“. Unless you understand completely what they
mean, we strongly suggest you to set it as “Disc at
Once“.
Max Audio VCD and CDG Speed - Audio CDís and
Video CDís do not have internal error checking capability,
so duplicating at too high a speed may cause frequent
errors. This setting will allow you to adjust the maximum
duplication speed for Audio and Video CD
DVD+R High Compatibility Mode -This feature will
allow you to enable/disable the DVD+R High
Compatibility Mode feature by turning this feature ON
or OFF. The purpose of this feature is to increase the
compatibility of DVD+R media with a broader range of
DVD Video players. This process will increase the
amount of time required to duplicate your disc(s).
Display and Sound Settings
Buzzer - This setting will allow you to choose
whether you want to hear a beep when you press a
button or when a task has been completed.
Start Up Menu - This setting will allow you to
choose which menu you would like to see first
when you turn on the duplicator
Screen Saver - . By enabling this feature, a
screen saver will be displayed when your
duplicator has been idle for a long period of time.
Language - This setting will allow you to
choose which language you prefer to navigate this
duplicator. Current supported languages are
Spanish, English
- 56 -
t
Reflex Duplicator Manual
Counter - This option will allow you to enable/disable
the Counter feature by turning this feature ON or OFF.
This feature will notify you how many discs have been
copied and how many discs are left to go.
Duplication Mode - To simplify Hard Drive loading and
copying process for anyone, we introduced a new
feature called “Load and Copy“ in addition to “On the
Fly“ under the new category “Duplication Mode“. For
more information, please refer to “Tutorial Guide XII Introduction to Duplication Mode“
Auto Start - This setting will allow you to choose Auto,
Full or Off. When it is Full, This feature will allow the
duplicator to copy automatically once your master disc
and all of the writer trays of the duplicator are fulfilled
with recordable media. When it is Off, the copy process
requires you to press “ENT“ button to confirm the
duplication. When it is Auto, if your duplicator has
detected 3 blank discs on a 4 target or higher duplicator
for example and didnít detect any additional blank discs
for 30 seconds, then the duplication will be started
automatically. However, in order for this feature to take
effect, you need to be inside the operation menu such
as COPY, TEST, TEST+COPY, and COPY+COMPARE
Load Default - This function will reset all of the options
back to manufactureís default. You can perform this
function if your duplicator is acting abnormal
6.
UTILITIES
Disc Info - If you are uncertain about the type of
blank recordable media you are using, the duplicator is
equipped with the disc info function to help identify and
notify you of the disc information encoded within
System Info - By entering this menu, you will be able to
see the many specification of your duplicator such as the
firmware version, CPU type, RAM capacity. You can
check the specifications by pressing UP or DOWN
button
- 57 -
t
Reflex Duplicator Manual
Device Info - By entering this menu, you will be able to
see the information for devices built inside your
duplicator
Drive Mileage - Shows total use of each drive and
entire system.
Update Firmware - This function will update the
software of your duplicator. To update, you need to
insert manufacture Certified Update CD into the Reader
and select this function by pressing “ENT“ button. We
strongly suggest you to not upgrade your duplicatorís
firmware unless your duplicator is getting unstable
Test Option
Compare - This menu will guide you to perform a
bit-by-bit comparison between the Master Reading
Source and all the copied discs inside the writer
tray. The purpose to perform this compare
operation is to ensure all of your copies have the
exactly same information as your Master Reading
Source
Verify - This menu will guide you to perform Disc
Readalibility Check. This operation will check the
readiblity of your mater discs and the copied discs.
The purpose to perform this verify operation is to
ensure all of your copies are readable.
Test Master
6.7 Manage Accounts - This feature allows you, the
administrator, to have the power to:
• Create user accounts and passwords to prevent
unauthorized use of this duplicator.
• Edit existing user account information, including name
and password.
• Delete existing user account(s).
• Enable/Disable this feature.
For more information, please refer to “Tutorial Guide XI
- Introduction to Account Management Feature.“
6.8 Format Hard Drive
- 58 -
t
Reflex Duplicator Manual
6.9 Erase - This menu will guide you to erase your
rewriteable discs in the WRITER Tray. There are two
options to erase your rewriteable discs: Full Erase: It will
erase the entire disc which will make it impossible to be
recovered. Quick Erase: It will erase the index of the
rewritable disc, not the data section.
7.
SHUTDOWN - Use this fuction to properly Turn-Off the
duplicator.
Trouble Shooting
1.
9
9
9
2.
9
9
9
3.
9
No display on LCD or the unit does not operate when the
power is on.
Check the connection of power cable and the environment
of power outlet is normal.
Make sure the power voltage matches the voltage of your
power outlet.
If the duplicator was stored in a location where the
temperature dropped below 32ðF (0ðC) within the past 24
hours, leave the duplicator in a warm room with
temperatures at least 65ðF (19ðC) for 4 hours prior to
powering it on.
READER cannot read disc and shows error message.
Check the format of the master CD/DVD or the master
CD/DVD itself for damage.
Your master disc may be copy protected. Most of DVDs and
some CDs purchased from stores have copy protection.
Use the Writers to read your master disc by selecting one of
writers as the Master Reading Source (Please refer to
Buttons do not function.
Maybe it is still busy on a task. Give it sometime and press it
again. If it still doesnít work, turn off the machine, and then
restart the machine after a minute.
- 59 -
t
4.
9
9
9
5.
9
9
9
Reflex Duplicator Manual
Copy completed but the copies are not readable /
executable?
Use “compare“ feature to check the copied disc.
Based on our experience, the quality of your media plays a
big role on this part. Try to use high quality media, such as
Disc Makers Ultra media, to prevent such problems.
Try another DVD/CD player/ROM to test the copied media.
Sometimes, your DVD/CD Player/ROM may not be
compatible with recordable DVD/CD disc.
The failure rate is high.
Lower the “write speed“ and try again. Please refer to
“Tutorial III - Select the Duplication Speed.“
Quality of blank disc may be poor.
Quality of your master disc may be poor.
6.
9
Do I need to upgrade my duplicatorís firmware?
Unless your system is getting unstable, we strongly suggest
not upgrading your duplicatorís firmware. Please contact our
Tech Support if your system is getting unstable.
7.
9
Cannot boot-up or fails to upgrade firmware.
Contact our Tech Support.
8.
Can I load data directly from my computer to my duplicatorís
Hard Drive?
No, your duplicatorís Hard Drive has a unique file system
that computers will not recognize. Thus, you canít perform
any read/write operations to the Hard Drive from your
computer.
9
9.
Why some writers wonít copy?
9 If those writers are connected with USB 2.0/Firewire
IEEE 1394 connections, please make sure the switch on
the back of the duplicator is off and restart your
- 60 -
t
9
9
Reflex Duplicator Manual
duplicator.
Reset back to default. ( Troubleshoot #11 )
Contact our tech support.
10. Why does my duplicator stay at “System Bootup“?
9 The reason you saw system bootup forever is caused by
improper shutdown. To solve the problem, please
contact our tech support for more information. Even
though this problem can be solved, all the hard drive
information will be lost due to this failure.
t
Reflex Duplicator Manual
11. How do I reset my duplicator back to default?
I)
Use UP or DOWN arrow button to navigate to the
following screen.
DISCMAKERS
5.Setup
1.12
II) Press “ENT“ to enter Setup Menu and you shall see the
following:
Setup
1. Select Burn Speed
III) Use UP or DOWN arrow button to navigate to the
following screen.
Setup
11. Load Default
IV) Press “ENT“ to enter Load Default Menu and you shall
see the following:
Load Default
Press OK to continue
V) Press “ENT“ to confirm and you system will be loaded
back to default. Once the operation is complete, you will
see the following:
Setup
12. Load Default
- 61 -
- 62 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement