- No category
advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
SL-236 Trim Kit - SP to FD
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SMA-665
SMA-665
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
Installation Instructions
CAUTION:
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING:
Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.
WARNING:
Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
2
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
PARTS
SMA-665
A (1)
[Bottom Panel Assembly, FD]
B (2)
[FD Trim, Sides]
C (2)
[FD Trim, Ends]
D (2)
10-24
F (14)
6-20 x 3/16"
E (6)
8-32 x 5/16"
3
SMA-665
ASSEMBLY AND INSTALLATION
1.
Remove and discard the Phillips screws holding the sides and front trim pieces to the SL236 box.
2.
Remove and discard the sides and front trim pieces. (See
Figure 1)
Side trim pieces
2
(C)
5
5 (F) x 10
Installation Instructions
(B) x 2
2 2
1 Front trim piece
Figure 1
3.
Remove four Phillips screws from rear trim piece. (See
Figure 2)
Rear of
SL-236
6
(F) x 4
5
6
Figure 3
6.
Place one end trim piece (C) on front and secure in place with four 6-20 x 3/16" Phillips tapping screws (F). (See
Figure 3)
7.
Remove six Phillips screws from rear of SL-236.
(See Figure 4)
Rear frame cover
(C)
Rear of
SL-236
4
8
7
9 x 6
3 x 4
Figure 2
4.
Remove and discard rear trim piece.
5.
Place side trim pieces (B) on sides and secure in place with ten 6-20 x 3/16" Phillips tapping screws (F). (See Figure 3)
Figure 4
8.
Add end trim piece (C) over outside edge of rear frame cover.
9.
Reinsert and tighten six Phillips pan head screws removed in Step 7. (See Figure 4)
NOTE:
The 8-32 x 5/16" Phillips pan head screws (E) may be used as replacement for the screws removed in Step 7, if necessary.
4
Installation Instructions
10. Loosen and remove two 10-24 nuts and cables from opposite corners of the SL-236. (See Figure 5)
11. Remove and pull bottom panel away from SL-236. (See
Figure 5)
SL-236 frame
SMA-665
14
12
13
(D) x 2
(A)
10 x 2
11
Cables
Spring clip
SL-236
Bottom panel
Figure 5
12. Raise bottom panel assembly (A) up to SL-236 and insert spring clips into rectangular holes on SL-236 frame. (See
Figure 6)
Figure 6
13. In corner with cable, install cable onto SL-236 frame and fasten with 10-24 nut (D). (See Figure 6)
14. Repeat in opposite corner of ceiling panel. (See Figure 6)
15. Continue installation following the SL-236 installation instructions.
5
6
SMA-665 Installation Instructions
Installation Instructions SMA-665
7
SMA-665 Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002751 Rev00
2015 Milestone AV Technologies www.chiefmfg.com
07/15
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
Europe
F 877.894.6918 / 952.894.6918
A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
Asia Pacific
F +31 (0) 495 580 845
A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project