User manual | RZR 2020 RZR 2021 RZR 2041

RZR 2020 RZR 2021
RZR 2041
Betriebsanleitung
Instruction Manual
Mode d’Emploi
Instrucciones de
Empleo
D
DEUTSCH
Seite
3 - 13
E
ENGLISH
page
14 - 24
F
FRANCAISE
page
25 - 35
ES
ESPAGNOL
página 36 - 46
2
E
Thank you for purchasing a Heidolph Instruments product. This item has been designed, made
and inspected in compliance with DIN EN ISO 61010 for long-term and flawless operation.
SUMMARY
SUMMARY ................................................................................................................................ 14
STANDARD HARDWARE & OPTIONS .................................................................................... 15
GENERAL INFORMATION ....................................................................................................... 16
SAFETY INFORMATION........................................................................................................... 16
SET-UP...................................................................................................................................... 17
OPERATION AND CONTROLS................................................................................................ 18
1.DESCRIPTION ......................................................................................................................... 18
2.Turn item ON ....................................................................................................................... 19
3.Speed setting....................................................................................................................... 19
4.Speed display……………………………………………………………………………………….20
CLEANING & SERVICING ........................................................................................................ 20
DISASSEMBLE & STORAGE................................................................................................... 20
DISPOSAL............................................................................................................................... 211
MALFUNCTION & REMEDY..................................................................................................... 21
SPECIFICATIONS ..................................................................................................................... 22
WARRANTY, LIABILITY & COPYRIGHT ................................................................................. 23
QUESTIONS / REPAIR WORK ................................................................................................. 23
CE-DECLARATION OF CONFORMITY.................................................................................... 24
Important information
Advise about power cord / mains supply
Caution: mandatory action
Caution: fire- and explosion hazard
Advise about maintenance / repair
14
E
STANDARD HARDWARE & OPTIONS
Standard Hardware
product
quantity
P/N
P/N
230 V / 50 Hz
115 V / 60 Hz
RZR 2020 or
1
501-20200-00
501-20200-01
RZR 2021 or
1
501-20210-00
501-20210-01
RZR 2041
1
501-20410-00
501-20410-01
support rod
1
22-02-14-01-08
22-02-14-01-08
2,5 mm Allen key
1
02-07-01-01-04
02-07-01-01-04
3,0 mm Allen key
1
02-07-01-01-02
02-07-01-01-02
10.5 mm chuck
1
509-02000-00
509-02000-00
T-handle (for chuck)
1
02-07-03-01-02
02-07-03-01-02
Instruction Manual
1
01-005-002-94
01-005-002-94
Accessories & Stirring tools (optional)
product
P/N
stand
570-12000-00
clamp
570-22000-00
protective sheath
509-08000-00
flexible stirrer coupling shaft
509-03000-00
stirring paddle BR 10
509-10000-00
stirring paddle BR 11
509-11000-00
stirring paddle BR 12
509-12000-00
stirring paddle BR 13
509-13000-00
stirring paddle BR 14
509-14000-00
prop-type stirring paddle PR 30
509-30000-00
prop-type stirring paddle PR 31
509-31000-00
prop-type stirring paddle PR 32
509-32000-00
prop-type stirring paddle PR 33
509-33000-00
turbine TR 20
509-20000-00
turbine TR 21
509-21000-00
half moon HR 18
509-18000-00
anchor AR 19
509-19000-00
prop-type stirring paddle PR 39
509-39000-00
enclosure NS 29/32
509-09000-00
15
E
GENERAL INFORMATION
Unpack your item carefully.
Inspect for damage and report such damage or missing parts to your supplier right away.
Read your Instruction Manual carefully. Take time to save time when working with your
product. Make sure that every user has read and understood the Instruction Manual.
Please store the Instruction Manual in a place easily accessible to every user.
IF ALL ELSE FAILS, READ THESE INSTRUCTIONS !
A so-called EURO-plug (DIN 49441 CEE 7/VII 10/ 16 A 250 V) is standard on all of the
products.
For the Continental US they feature a US-standard plug (NEMA Pub.No.WDI.1961 ASA
C 73.1 . 1961 page 8 15A 125V).
For using the item in a country with deviating outlet / plug systems, we recommend to
use approved adapters or to have an electrician replace the standard plug with one suiting your needs.
As shipped, the item features a protective ground wire. When replacing the original plug,
make sure to reconnect this protective ground wire in the new plug !
SAFETY INFORMATION
Please comply with all safety and accident-prevention regulations as in force for
laboratory work !
Use extra care when working with flammable substances; refer to safety data
sheets.
When connecting your item with your local power supply, please make sure your
item is designed for your local voltage; go by the data plate on the item.
Turn your power switch OFF whenever the item is not used, or before disconnecting the plug.
Repair work is limited to technicians approved by Heidolph Instruments.
Use extra care when working in the vicinity of flammable and explosive substances. Motors are of non-sparking type, the item itself however is not explosionproof.
Please connect your stirrer with a protective-ground outlet only.
Please strictly comply with current safety regulations for machines exposing rotating shafts.
Your item needs a solid stand.
16
E
SET-UP
1. Install stand
make sure the indent (A) of the rod is in line with threaded pin (B).
Install stand in hole (C) in the rear of the item. Secure (pull tight)
threaded pin (B) using Allen key (D).
E F
H
B
D
C
A
G
2. Install chuck
make sure the indent (E) in the drive shaft is in line with threaded
pin (F) in the chuck. Secure threaded pin (F) with allen key (H) in
your hardware bag.
K
L
J
I
3. Install stirrer on stand
Install clamp (I) on stand (J).
Now introduce stirrer attaching rod (K) into clamp (I).
Adjust position and secure (pull tight) with two clamp screws (L).
L
M
G
N
4. Install stirring tool
Introduce stirring tool (N) in chuck (G), put in place and secure
with T-handle (M). Immersion depth of your stirring tool (N) is adjusted by displacing the tool in or out the open (G) chuck (refer to
arrow mark).
G
P
5. Install flexible coupling shaft (P/N 509-03000-00)
Hold the flexible coupling shaft (O) in the chuck (G) by its metallic stud
(P) and secure with T-handle. At this point introduce stirring tool’s (N)
shaft end in collet (Q) and pull tight (CW turn).
When using the flexible coupling shaft make
sure to install an adequate run-out protection,
e.g. our enclosure (P/N 509-09000-00)
17
O
Q
N
E
S
6. Install shaft guard (P/N 509-08000-00)
A shaft guard (R) is available as an extra safety protection feature. This guard tube is held by 2 ea. screws (S) located at the
top of the stirrer chuck.
This guard, attached to the stirrer housing, is used to protect
the user from being hurt by the fast-spinning shaft.
S
R
OPERATION AND CONTROLS
1.
Description
The HEIDOLPH stirrers RZR 2020, RZR 2021 and RZR 2041 are user-friendly and are specifically designed for laboratory use. They are equipped with a maintenance-free capacitor motor
with steplessly variable gear. A straightforward 2-stage gear provides the wide speed range. All
the elements are maintenance-free and free of wear and tear to a large extent.
The hollow drive shaft provides great flexibility for fast and easy paddle adjustment.
1.1
Overload protection
The RZR 2020, RZR 2021 and RZR 2041 are equipped with a thermal overload protection feature to prevent damage to the stirrer caused by overloading or blocking. In such cases the motor shuts itself off automatically. Once this mechanism has been triggered, the stirrer must be
allowed to cool down before being restarted via the ON/OFF switch (C). If the motor shuts itself
off due to overloading, this is indicated by a red pilot lamp (A).
1.2
Stirring shaft protection
A protective device made of plexi-glass (PMMA) is available as an optional accessory to protect
the user from injury. It is fastened to the housing and protects the operator from injuries resulting from splashes or from unintentional contact with the rotating shaft.
A
E
B
C
D
18
(RZR 2021 / 2041)
E
2.
Turn item ON
Make sure that the voltage of the instrument is the same as the mains supply. The
instrument's voltage is specified on the serial plate underneath the instrument
Make sure that the speed control knob (D) is turned all the way to the left.
Only plug the instrument into a grounded (earthed) electrical outlet. The on/off switch (C) is
used to turn the instrument on and off. The green pilot lamp (A) should light up when the instrument is operational.
Always use the mains rotary switch (C) to switch off the mixer. Do not pull out the
plug. The friction ball of the friction gear is disengaged by using the mains rotary
switch (C), which prevents any knocking noises when starting the mixer.
3.
Speed setting
Set the desired speed range using the selection switch (B).
The stirrer has two speed ranges:
Range I: 40 - 400 rpm
Range II: 200 - 2000 rpm.
Only change the speed range when the instrument is switched off, so as not to damage the gear. It is advisable to turn the
chuck slightly whilst selecting another
speed range. Only operate the instrument
when the marker is exactly on I or II -(no intermediate settings).
The selection switch (D) is used to select the desired speed
within range I or II.
The scales are numbered from 1 to 10 and only serve as a guide. The speeds pertaining to the
two ranges are specified separately on the side of the stirrer RZR 2020.
When changing over from speed I to speed II, the stirrer speed increases fivefold.
(from 40 - 400 rpm to 200 - 2000 rpm). As this gives rise to splashing (especially in
conjunction with open containers), the instrument must be switched off before the
operator can switch from speed range I to speed range II.
If the operator attempts to switch from range I to range II or vice versa whilst the instrument is
in operation, the motor shuts off and the red pilot lamp (A) lights up.
19
E
An integrated safety feature ensures that it is only possible to switch from range I
to II or vice versa under the following conditions:
Procedure:
•
Switch stirrer off via the ON/OFF switch (C).
•
Turn speed control knob (D) all the way to the left.
•
Set speed range from I to II (or vice versa) with switch (B). Switch instrument
back on with ON/OFF switch (C).
Set desired speed via speed control knob (D).
•
4.
Speed display
RZR 2021 and RZR 2041 are equipped with a digital display (E) for reading the mixer speed.
CLEANING & SERVICING
Cleaning: wipe housing clean with a damp cloth (add some sort of mild liquid soap).
Note
To avoid damage to the surface finish, avoid using chlorine bleach, chlorine-based detergents, abrasive substances, ammonia, rags or cleaning
agents containing metal particles.
The item is maintenance-free. Repair work is limited to technicians approved or appointed by
Heidolph Instruments. Please call your local Heidolph Instruments Dealer or a Heidolph Instruments Field Representative (also refer to page 23)
DISASSEMBLE & STORAGE
Disassamble (refer to page 17, „set-up“)
Turn the item OFF and pull power plug.
To disassamble the item easely, remove all flasks, containers or other appliances in the vicinity
of the stirrer.
Open chuck with T-handle and remove stirring tool.
Unlock clamp and remove stirrer head from head clamp.
With 2,5 mm Allen key loosen threaded pin and remove chuck. With the 3 mm Allen key loosen
and remove stand rod.
Forward & Store
1. We recommend to store the item and its components in its original box, or a similar container
that offers adequate protection against damage in transit. Tape the box securely.
2. Store the item in a dry place.
2. Caution
Do not jolt or shake the item during transport.
20
E
DISPOSAL
For disposal, please comply with your local or national regulations.
Split by metal, plastic, etc.
Packing material to be treated as described above (material split).
MALFUNCTION & REMEDY
1. pilot lamp dim
- check power supply and power cord
2. won’t stir:
-
safety installation intervened, refer to display reading (refer to 5 „safety installations“)
3. LED (A) illuminates red:
- The mixer motor stops during the attempt to switch the device from area I to II or vice
versa during operation and the warning light (A) illuminates red. (Compare with 3.
"Speed setting")
4. When switching from area I to II or vice versa, switch gets stuck or is difficult to move: In order to aid the process, it is advantageous to use a slight twisting motion on the chuck while
switching. After this, only operate the device if the indicator of the rotary switch is precisely in
position l or II (meaning not an intermediate position). (Compare with 3. "Speed setting")
In case of a malfunction and you cannot correct with above instructions, contact your authorized
Heidolph Instruments Dealer.
21
E
SPECIFICATIONS
power dissipation (nom. load)
power dissipation (nom. load)
power rating, motor,
power rating, motor,
dimensions (in mm) RZR 2020 / 2021
dimensions (in mm) RZR 2041
weight RZR 2020 / 2021
weight RZR 2041
operating temperature
storage temperature
relative humidity
protection class
Torque
speed range
stirrer coupling
stirrer attaching system
motor protector
pilot light, „item ON“
shaft guard
BCI/TVI suppression
operational mode
display ( RZR 2021 und RZR 2041 )
measuring range, display
Resolution
Display accuracy
Measuring principle
RZR 2020 / 2021 P = 50 watts
RZR 2041
P = 70 watts
RZR 2020 / 2021 P = 27 watts
RZR 2041
P = 37 watts
82 wide; 206 high; 176 deep
82 wide; 211 high; 176 deep
3 kg
3.8 kg
0 – 40 °C
- 20 to + 80 °C
95 % (avoid reaching dewpoint)
IP 40
refer to graphs below
40 – 2000 rpm
range 1: 40 – 400 rpm
range 2: 200 – 2000 rpm
10,5 mm chuck, drive shaft features bore to hold tool
shafts of up to 10 mm dia.
13 mm dia. Rod (stand)
thermal circuit breaker disconnects motor in an overload situation - permanent cut-off - pilot lamp (green);
RESET with ON/OFF key
pilot lamp (green)
fits shaft guard (optional)
complies with EN 50081
100% continuous
4-digit LCD, 8 mm high characters
40 – 2000 rpm
1 rpm
+/- 0,1% of final value
hall sensor with ring magnet (5 pairs of poles)
Torque
RZR 2020 / 2021
RZR 2041
350
300
Range 1
200
150
Ncm
Ncm
250
Range 2
100
50
0
0
400
800
1200
1/min
1600
500
450
400
350
300
250
200
150
100
50
0
2000
Range 1
Range 2
0
22
400
800
1200
1/min
1600
2000
E
WARRANTY, LIABILITY & COPYRIGHT
Warranty
Heidolph Instruments guarantees warranty that the present product shall be free from defects in
material (except wear parts) and workmanship for 3 years from the date shipped off the manufacturer’s warehouse.
Transit damage is excluded from this warranty.
To obtain such warranty service, contact Heidolph Instruments (Tel.: +49 - 9122 - 9920-68) or
your local Heidolph Instruments Dealer. If defects in material or workmanship are found, your
item will be repaired or replaced at no charge.
Misuse, abuse, neglect or improper installation are not covered by this warranty guarantee..
Alterations to the present warranty guarantee need Heidolph Instruments’ consent in writing.
Exclusion Clause
Heidolph Instruments cannot be held liable for damage from improper use or misuse. Remedy
for consequential damage is excluded.
Copyright
Copyright in pictures and wording of the present Instruction Manual is held by Heidolph Instruments.
QUESTIONS / REPAIR WORK
If any aspect of installation, operation or maintenance remains unanswered in the present
Manual, please contact the following address:
For repair services please call Heidolph Instruments (phone: +49 - 9122 - 9920-68) or your local, authorized Heidolph Instruments Dealer.
Note
You will receive approval for sending your defective item to the following address:
Heidolph Instruments GmbH & Co. KG
Lab Equipment Sales
Walpersdorfer Str. 12
D-91126 Schwabach / Germany
Tel.: +49 – 9122 - 9920-68
Fax: +49 – 9122 - 9920-65
E-Mail: [email protected]
23
01-005-002-94-1
04/2004
 Heidolph Instruments GmbH & Co. KG
Technische Änderungen sind ohne vorherige Ankündigung vorbehalten.
Technical changes reserved. Publication not mandatory.
Sous réserve de modifications techniques sans notification préalable.
Nos reservamos el derecho de introducir modificaciones técnicas sin previo aviso.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project