dazzle™ dmx pixel rgb led strip light

dazzle™ dmx pixel rgb led strip light
®
5V
DMX
COMPATIBLE
DAZZLE™ DMX PIXEL RGB LED STRIP LIGHT
COLOR-CHANGING
DRY/WET LOCATION
DC
SPECIFICATION SHEET
• DMX addressable / chasing
• Outdoor / wet location
• UL Recognized Component
• 3-year limited warranty
W 0.55 in. (14mm)
L 39 in.
SPECIFICATIONS
E348119
DAZZLE® DMX
E348119
®
E348119
CCT
(Kelvin)
Item #
DI-5V-DDMX-0008
Red (625nm)
Green (525nm)
Blue (465nm)
CONT’D Connections ² : OUTPUT - Power:
39.4 in. (1M) 20/2 AWG male wet location plug.
Data: 39.4 in. (1M) CAT5 cable with female RJ45
connection
Dimmable: Yes with compatible DMX controller
Ambient Temp ³ : -4 ~ 122°F (-20 ~ 50°C)
Operating Temp ⁴ : -4 ~ 176°F (-20 ~ 80°C)
Environment ⁵ : Outdoor / Wet location
Dimensions: 0.75 x 0.25 in. (W x H)
Certifications: UL Recognized Component,
E348119
Lumens / ft. ⁶
CRI
Efficacy
(lm/W) ⁷
394
-
13.33
Note ¹ Each maximum run requires a dedicated feed from the driver (power) or DMX controller (data). Do not extend beyond the
recommended maximum run lengths. See the installation guide for system diagrams.
Note ² DMX data only travels in one direction.
Note ³ Do not install product in an environment outside the listed ambient temperature. Exceeding the maximum ambient temperature
may damage LED chips, reduce the total lamp life, lumen output, and/or adversely impact color consistency.
Note ⁴ Operating temperature is measured according to the minimum and maximum ambient temperature environment.
Note ⁵ Do not install in environment where LED chips are exposed to direct sunlight as damage to the phosphor will occur.
Note ⁶ LED chips have a luminous flux range with a tolerance of +/- 5%.
®
DAZZLE® DMX
E348119
E348119
L 39 in.
DAZZLE® DMX
E348119
OUTPUT
1x Female RJ45 (Data)
1x Male Wet Location
Connector (5V Power)
DMX data travels in one direction
®
E348119
INPUT
1x Male RJ45 (Data)
1x Female Wet Location
Connector (5V Power)
Input Voltage: 5VDC Constant Voltage
Power Consumption / ft.: 2.81W / 562mA
LED Chip Type: 5050 RGB Tri-Chip SMD
LED Chip Beam Angle: 120°
LED Chip Spacing: 1.25 in. between centers
LED Chips / ft.: 10
Mounting: Mount with included clips or silicone
adhesive (sold separately)
Field Cuttable: Not recommended
Maximum Run (Power) ¹ : 8.2 ft.
Maximum Run (Data) ¹ : 16.4 ft.
Connections ² : INPUT - Power: 39.4 in. (1M)
20/2 AWG female wet location plug. Data: 39.4
in. (1M) CAT5 cable with male RJ45 connection
®
W 0.83 in.
(21mm)
W 0.75 in.
(19mm)
H 0.25 in.
(6mm)
DAZZLE™ DMX PIXEL LED STRIP LIGHT SERIES
Item #:
Project:
1 OF 4
SS012215-2.3
DMX CONTROLLERS
Item #
Type
Description
DI-1726
Nicolaudie STICK 1
DMX Color Controller
Our most sophisticated unit offers professionalgrade DMX512 control in a user-friendly control
pad.
DI-1720
Nicolaudie STICK 2
DMX Color Controller
Sophisticated and modern touch-sensitive
keypad selects mode, speed, and dimming.
DI-1727
Nicolaudie Easy Stand
Alone DMX LED Color
Controller
Program lighting scenes from a computer to
the independent free-standing controller.
DI-1808-K
SQUARE-PRO
Junction Box
Image
Included with the following controllers: DMX
WiFi Wall Mount Zone LED Controller, Nicolaudie
STICK 1 Controller, and Nicolaudie STICK 2
Controller. Also sold separately.
Features 3x 0.5 in. and 5x 0.75 in. knockouts.
Dimensions: 2.83 x 1.89 x 2.83 (L x D x H)
5V DMX POWER SUPPLIES
DAZZLE DMX PIXEL RGB LED STRIP LIGHT is only compatible with the following 5VDC power supplies.
Item #
DI-PA-5V25W-B
DI-CV-5V25W
Type
Description
5V 25W Plug-in
Adapter (Black)
5V 25W plug-in LED driver. Purchase a Wet
Location Plug to DC Plug Connector (See
Accessories) to connect DAZZLE DMX tape
light directly to plug-in-adapter.
4.7 x 2 x 1.25 in. (L x W x H)
5V 25W Constant
Voltage Driver
Hard-wired 5V 25W LED driver. Install in a
standard 4 x 4 in. electrical enclosure if required
for installation (not included).
3.07 x 2.01 x 1.10 in. (L x W x H)
Image
L
N
G
VV+
Note: All accessories sold separately
DAZZLE™ DMX PIXEL LED STRIP LIGHT SERIES
2 OF 4
SS012215-2.3
DMX ACCESSORIES
Item #
DI-1918
DI-0820 (female)
DI-0821 (male)
Type
Description
DMX 4-Channel
Decoder
Pair with a DMX controller to control solid color,
RGB, and RGBW LED fixtures. Features a
digital display for easy addressing.
Wireless DMX
Transmitter/
Receiver
Wirelessly connects DMX devices: Fixture to
fixture, fixture to controller, and decoder to
decoder. Features XLR-3 connections.
DI-1804
DMX 8-Way
Splitter
Amplifies and splits a DMX signal up to 8 ways.
Features 1x male XLR-3 input connection, and
8x female XLR-3 output connections.
DI-1803
DMX XLR-3
Connector Pair
Utilize this XLR-3 connector pair to create
custom length DMX extensions. Sold by the
pair (male/female). Male: 2.8 x 0.71 in. (L x Dia.)
Female: 2.4 x 0.71 in. (L x Dia.)
DI-1806
XLR-3 to
RJ45 Adapter
Connector Pair
Converts RJ45 data cables to XLR-3 DMX
connections. Sold by the pair (male/female)
Male & Female: 2.58 x 0.87 x 0.98 in. (L x W x H)
DI-1809
20 ft. DMX
XLR-3
Extension
Cable
Creates an extension between DMX fixtures
and accessories. Features XLR-3 connections.
Wire: 18/3 AWG. Male connection: 2.8 x 0.71
in. (L x Dia.) Female: 2.4 x 0.71 in. (L x Dia.).
DI-1807
RJ45 Coupler
Female-to-female accessory quickly connects
two RJ45 accessories.
1.22 x 0.44 x 0.87 in. (L x W x H)
RJ45 Splice
Cable
Creates a RJ45 connection to bare wire leads for
DMX applications. 6.5 x 0.4 x 0.6 in. (L x W x H)
39.4 x 0.4 x 0.6 in. (L x W x H)
DI-1811
XLR-3 to RJ45
Adapter Cable
Pair
Converts RJ45 port of 4-Channel DMX Decoder
to a standard XLR-3 connection. Sold by the pair
(male/female). 20 x 0.71 in. (L x Dia)
DI-1911 (10ft)
RJ45 Extension
Cable
Creates a 10 ft. extension between DMX fixtures
and accessories utilizing RJ45 connections.
0.4 x 0.6 in. (W x H)
DI-0710-M
DI-0710-F
Wet Location
Plug to DC
Plug Connector
Utilize to connect plug-in adapter directly to
DAZZLE DMX Strip Light. Gender specification
applies to the wet location connection only.
Wire: 22/2 AWG. 7 x 0.3 in. (L x W).
DI-1805 (male, 6.5in)
DI-DMX-RJ4539-SPLE-F
DI-DMX-RJ4539-SPLE-M
(Male)
(Female)
Image
Note: accessories sold separately
SYSTEM DIAGRAMS
See the ‘DAZZLE DMX PIXEL RGB LED STRIP LIGHT Installation Guide’ for system diagrams and installation instructions. For additional questions
and concerns please contact technical support.
DAZZLE™ DMX PIXEL LED STRIP LIGHT SERIES
3 OF 4
SS012215-2.3
ADDITIONAL RESOURCES
Visit the online product page at www.DiodeLED.com for additional resources including:
• DAZZLE™ DMX PIXEL RGB LED TAPE LIGHT Installation Guide
For system diagrams and full installation instructions.
• Voltage Drop Charts
Use to specify appropriate wire gauge for installation. Available at the ‘Tools & Resources’ page at www.DiodeLED.com.
SAFETY & DISCLOSURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Install in accordance with the National Electric Code and local regulations.
This product is intended to be installed and serviced by a qualified, licensed electrician.
This product requires a compatible LED driver for proper configuration. Do not connect directly to high voltage 120~277V AC power.
The UL certification of this product requires the fixture to be powered with a compatible Class 2 DC constant voltage LED driver (power supply).
It is generally recommended to load the driver no more than 80% the labeled rating for maximum performance and longevity. However, see each
driver specification sheet for exact minimum and maximum loading values.
Do not install product in an environment outside the listed ambient temperature. Exceeding the maximum ambient temperature may damage LED
chips, reduce the total lamp life, lumen output, and/or adversely impact color consistency.
Operating temperature is measured according to the minimum and maximum ambient temperature environment.
Do not power tape light on the plastic spool or when tightly coiled. Excess heat may melt the spool and/or cause damage to the product.
Ensure adequate airflow and heatsinking is considered when mounting/installing. Exceeding the maximum operating temperature may damage LED
chips by reducing the total lamp life, lumen output, and/or adversely impact color consistency.
Each maximum run requires a dedicated power feed from the driver. Do not extend beyond the recommended maximum run length.
Ensure applicable wire is installed between driver, fixture, and any controls in-between. When choosing wire, factor in voltage drop, amperage
rating, and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires, and cause fire.
‘Voltage drop’ is a gradual decrease in voltage along a conductor through which current is flowing. When specifying an LED system, ensure to
calculate voltage drop appropriately. Voltage drop calculators will suggest the proper gauge wire and distance to install the driver from the fixture.
To meet maximum performance, the beginning of the tape light should be receiving no less than 3% of input power rating.
Tape light must be handled with care. Excessive handling, bending, and pressure may damage the product, voiding the warranty.
Tape light, attached wire leads, and additional extension cables, connectors, etc., are not rated for in-wall installation unless otherwise noted.
Ensure wire leads at opposing ends of the tape light are not crossed when the fixture is turned on. It is acceptable to modify the length or cut off
the attached wire leads and DC connections in the field.
Actual color may vary from what is pictured on this sheet and other print materials due to the limitations of photographic processes.
Lighting technology has some amount of gradual light degradation (output and/or color) over the lifespan of the products. Diode LED products are
designed to minimize degradation, but some light degradation and color shift is a normal part of the life span of any LED lighting system.
We reserve the right to modify and improve the design of our fixtures without prior notice. We cannot guarantee to match existing installed fixtures
for subsequent orders or replacements in regards to product appearance, CCT, or lumen output.
WARRANTY INFORMATION
Limited Warranty
This LED product has a three (3) year limited warranty from the date of shipment. This warranty does not include the additional accessories referenced
in this specification sheet. Complete warranty details for fixtures and additional accessories are available at www.DiodeLED.com under the ‘Tools &
Resources’ tab. For warranty related questions, please contact customer service.
Consumer’s Acknowledgment
Diode LED stands behind its products when they are used properly and according to our specifications. By purchasing our products, the purchaser
agrees and acknowledges that lighting design, configuration and installation is a complex process, wherein seemingly minor factors or changes in
layout and infield adjustments can have a significant impact on an entire system. Choosing the right components is essential. Diode LED is able to
work with the original purchaser to make an appropriate product selection to the extent of the limited information that the customer can provide, but
it is virtually impossible for Diode LED to design a system that foresees every unknown factor. For this reason, this Warranty does not cover problems
caused by improper design, configuration or installation issues. Any statement from a Diode LED employee or agent regarding a customer’s bill of
goods and/or purchase order is NOT an acknowledgement that the products purchased are designed and configured correctly. The purchaser agrees
and acknowledges that it is the customer’s responsibility to adhere strictly to all information contained in the Product Specification Sheets.
There is often more than one way to design, configure and layout an LED lighting application properly to achieve the same lighting effect. Diode LED
strongly recommends that licensed professionals be used in the design and installation of lighting systems that include Diode LED products. The
specifications include important information that a designer and installer should carefully review and strictly follow. Qualified designers and certified
and/or licensed installers, with access to the final installation environment, customer goals, and Diode LED product specifications can make the
requisite decisions appropriate for a successful finished lighting application.
® Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2014 Elemental LED, Inc. dba Diode LED. All rights reserved. Specifications are subject to change without notice.
DAZZLE™ DMX PIXEL LED STRIP LIGHT SERIES
D4 OF 4
SS012215-2.3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising