owner`s manual - Ag Spray Equipment

owner`s manual - Ag Spray Equipment
OWNER’S MANUAL
55 Gallon Quic-Tach (CAT I) 3 Point Sprayer
(55 Gallon-3PT Sprayer w/Plumbing)
General Information
Thank You and Congratulations on
purchasing your new three point hitch
sprayer. The purpose of this manual
is to assist you in operating and maintaining your 3-Point sprayer.
Please read it carefully, as it furnishes
information which will help you achieve
years of trouble-free operation. All units
can be custom equipped to meet all
your spraying needs. The QT Series 3
Point is designed to fit Category I Lift
Arms.
Shown for reference ONLY
Any Questions, Comments or Problems: Call your nearest AG SPRAY Location
and speak with one of our Friendly Technical Support Staff.
06/17
BAKERSFIELD, CA
COLUMBUS, NE
DOTHAN, AL
FARGO, ND
GREENWOOD, MS
877-724-2236
800-274-1025
800-227-4098
701-280-2862
800-844-4524
HOPKINSVILLE, KY
MANKATO, MN
NEWTON, KS
OTHELLO, WA
TEMPE, AZ
800-637-7172
507-388-6295
800-394-7662
800-634-2026
877-974-7166
VISIT US ONLINE @
WWW.AGSPRAY.COM
Page 1
Table of Contents
3-6
Safety Information
6
Hooking Up Sprayer
7
Sprayer Boom Control
8-10
Calibrating Sprayer
11
Calibrating Sprayer: Boomless Nozzle Application Charts
12
Calibrating Sprayer: Broadcast & Turf Application Chart 20” Spacing
13
Calibrating Sprayer: KLC, TurboJet & AIXR Application Charts
14
Operating Instructions
15-16
Maintenance Instruction
16
Winterizing Sprayer
17-26 Component Assembly Breakdowns
17
55 Gallon 3 Point Assembly Breakdown - Base Unit
18
BoomBuster Kit w/XT024 Nozzles
Rooster Kit w/#10 Hamilton Nozzle
19
FSBK-1 & FSBK-2 Boom Kit Assemblies
20
FSBK-5 & FSBK-70 Boom Kit Assemblies
21 -22
FSBK-3025BL Boom Kit Assembly
23
409 Deluxe Handgun Kit Assembly
411 TeeJet 43H Handgun Kit Assembly
24-26
6500 Pump Assemblies
27
Warranty
Page 2
Important Operation & Safety Information
WARNING
Read and understand this owner’s manual completely before using the sprayer.
Read each chemical label’s instructions before handling the chemical.
Improper use of the sprayer or handling of chemicals could result in serious injury or illness for
the operator or nearby persons/animals, or cause damage to the environment.
LISTED BELOW is a summary of safety information of particular importance. See individual sections of this
owner’s manual for more details.
---------------------------- BEFORE YOU BEGIN ------------------------------Please read and understand this manual and its instructions and warnings completely before operating the
sprayer.

Be aware of all safety guidelines, warnings and cautions including those of the tractor manufacturer

Read and understand the chemical manufacturer’s labels, warnings and instructions

Know and fulfill all state pesticide applicator license requirements

Familiarize yourself and other operators with the sprayer’s components and how all parts are operated
------------------------- General Safety Guidelines ---------------------------Every year many unnecessary accidents occur do to improper equipment handling and a disregard for safety
precautions. You, the operator, can avoid accidents by observing the precautions in this section.

The operator should be a responsible adult. Do not allow persons to operate this sprayer until they have displayed a
thorough understanding of sprayer safety precautions and operational use!

All operators must also fulfill state pesticide applicator license requirements

Never attempt to operate this sprayer when under the influence of alcohol or drugs.

The best defense against accidents is a careful and responsible operator. If your sprayer is equipped with a PTO
drive shaft, it is very important to take the proper safety precautions

Failure to keep body parts or clothing clear of the sprayer’s PTO drive shaft could result in serious injury or death.
Ag Spray assumes no liability for any possible injury

Never step over or work near the PTO drive shaft during operation

When transporting the sprayer on public roads, always follow state and local regulations regarding safety and
transportation requirements
Page 3
Important Operation & Safety Information
------------------------------- Before Operation ----------------------------------

Carefully study and understand the owner’s manual

Read and follow chemical manufacturer’s labels, warnings and instructions! A material safety data sheet (MSDS) should be
provided by the chemical manufacturer

To avoid injury from chemical hazards, wear the proper protective clothing. Each chemical manufacturer’s clothing requirements
are listed under the “Personal Protective Equipment (PPE)” section in the chemical instructions

Never exceed your tractor’s load rating

Do not wear loose-fitting clothing which may catch in moving parts

Give the sprayer a visual inspection for any worn parts, loose bolts or other visible problems and make any needed repairs

Make sure the area is clear of any people or obstructions before using the sprayer

Before adding chemicals, have all operators practice operating the sprayer (clean water only) and it’s attachments until all
operators are completely capable of safe operation
------------------------- BEFORE SEASONAL USE ----------------------------

CHECK and TEST sprayer with water before adding chemical. Temperature change can cause material fitting expansion/
contraction. Serious injury could result from chemical leaks

REPLACE any worn or frayed hoses. Hose failure can result in serious damage

INSPECT pressure gauge. Insure the needle rests at zero when all pressure is relieved in the spray system. Failure to have a
properly functioning pressure gauge can result in miss applications of chemical
---------------------------- DURING OPERATION -------------------------------

Always be aware of bystanders, particularly children! Always look before moving the sprayer or engaging the PTO

Never leave running equipment unattended!

Keep hands and body parts clear of all moving parts, especially the tractor PTO

Be aware of dangerous terrain such as holes, slopes, drop-offs, banks, rocks and hidden hazards. Operate the tractor and
sprayer up and down slopes, not across

When operating on inclines, it is especially important that your tractor is equipped with Roll Over Protection System (ROPS)

No passengers are allowed on or in the tractor or sprayer at anytime

Allow for sprayer boom length when making turns
 Remember that accidents can even happen to seasoned operators. Always take your time and follow all safety instructions
Page 4
Important Operation & Safety Information
-------------------------- General Chemical Safety -----------------------------

READ and FOLLOW all chemical label’s instructions and warnings

AVOID inhaling, ingesting or coming into contact with any chemicals

KNOW applicable licensing and regulatory requirements for the chemical you plan to use

KNOW emergency procedures before handling chemicals

WEAR protective clothing, eye protection and chemical resistant gloves when filling, using and cleaning the sprayer. Wear
additional protective gear, such as facemask or apron, as recommended on the chemical label

EXERCISE EXTRA CAUTION around children or pets. Pesticides are especially toxic to them. Keep sprayer and spray
materials away from them at all times

DO NOT MIX OR POUR chemicals in an enclosed, unvented area

DO NOT USE flammable or corrosive chemicals in the sprayer

FLUSH the sprayer with clean water after every use AND before switching chemicals

STORE pesticides in a correctly labeled container and in a secure location

MONITOR the health of operators frequently exposed to pesticides, as recommended by the chemical label or local/federal
regulations
----------------------- Chemical Application Safety --------------------------

INSPECT and PREPARE sprayer before each use as directed

DO NOT TURN ON POWER to sprayer until ready to spray in order to avoid unintended spray release

MAKE SURE NOZZLES ARE ORIENTED IN THE PROPER DIRECTION before starting the sprayer. As incorrectly positioned
nozzle may spray chemicals on you or others

KEEP sprayer and spray materials away from children and pets. Pesticides can be especially toxic to children and animals
------------------------- Pump Safety Precautions ----------------------------

Never pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc.

Never pump acids (i.e. acid fertilizer) with super rollers. For acid fertilizer, Hypro recommends the Silver Series castings with
Teflon rollers

Never run the pump dry! Never pump faster than, or above, the maximum recommended speed and pressure

Never pump liquids at temperatures higher than the recommended maximum temperature (140° F/60° C). Do not exceed this
temperature

Before servicing your pump, disconnect the power, release all pressure and drain all liquids
Page 5
Important Operation & Safety Information
----------------------------- Following Operation --------------------------------

Following operation, it is very important that you completely rinse the entire sprayer and all of it’s components of all chemical
residue

Following operation, stop the tractor unit, set the brakes, disengage PTO shaft, shut off the engine and remove the ignition key

Park the sprayer on a hard level surface

Store the sprayer away from human and livestock activity

Do not permit children to play on or around sprayer
Hooking Up the Sprayer
Your QT Series 3 Point sprayer is designed to allow for a Category I 3 Point hitch. The hitch design will fit most brands of 3 Point
Quick Tach. The unit comes standard with Category I lower link pins (7/8”). You will need to supply a top link pin. One is NOT
furnished because of the WIDE range of top link arm attachments.
Category I
Page 6
Sprayer Boom Control
Familiarize yourself with the sprayer control before use. Sprayer is equipped with a manual
boom control.
Your sprayer is equipped with the AA6B manual control valve:
The spray booms will be ON when the handle is in the down or activated position.
The booms will be OFF when the handle is pointed straight out or deactivated position.
When you are ready to start spraying, push the
selector handle down to activate the boom.
To shut off the booms, pull the handle straight out.
‘Directo Valve’ - Manually Operated Control Valve
 Corrosion Resistant Materials: Wetted Parts Polypropylene, 316SS
and Polyethylene
 Maximum Pressure = 150 p.s.i.
 Large Capacity - 12.5 G.P.M. @ 5 p.s.i. Pressure Drop
 3/4” NPT (F) Inlet Connection
 1/2” NPT (F) Spray Line Connection
 3/4” NPT (F) Continuous By-Pass Connection
 Valves may be connected w/close nipples for multiple section spray
control
* * Items available in Repair Kit ONLY
Page 7
Calibrating the Sprayer
When spraying with a boom, the sprayer must be calibrated to ensure proper spray coverage and to combat overapplication or under application. Before calibrating the sprayer, it is important to familiarize yourself with the operating
instructions. The calibration process is simplified when broken down into the following three steps:
1. Determine the speed of the tractor
2. Determine the nozzle size and use the calibration chart to find the correct pressure setting
3. Set the pressure accordingly using the pressure regulating valve
Note: All calibration must be done with clean water only!
1. Determining the Speed
Note: it is helpful for future references to record the
exact RPM and gear that was used to attain the
desired speed
Tractor RPM
Tractor Gear =
___________
___________
Speed
___________________
It is important to determine what speed the tractor will be traveling at, while spraying. While some tractors have speedometers, it is still recommended that speed is calculated for all tractors for accuracy purposes. To determine the speed
follow these steps:
1. Set the tractor throttle to operate between 75%-100% of the tractor’s RPM range. This will allow the pump to operate
at full volume
2. Measure a 200 foot or 300 foot distance on a field or a surface similar to where you will be spraying
3. Drive the tractor and sprayer (tank half-full is optimal) across the measured distance at a constant rate of speed.
There should be no changes in speed while you are measuring the time. This should be a comfortable speed for
spraying
4. Have someone measure the amount of time (in seconds) it takes to travel the measured distance
5. Your speed can be found by entering your data into the equation below or by consulting the speed table
Speed (MPH) = (Distance (FT) x 60)/(Time (Seconds) x 88)
_____(MPH) = _____(FT) x 60/ _____(SEC) x 88
Speed Chart
Time Required in seconds to travel a distance of
Note: When calculating tractor speed be sure to
select a gear that allows the tractor to operate
between 75%-100% of the tractor’s RPM range.
This will allow the pump to operate at full volume.
Selecting a higher gear will not allow the pump to
work efficiently.
Page 8
Speed in M.P.H.
(Miles Per Hour)
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
8.0
9.0
10.0
200 Ft.
136
91
68
55
45
39
34
30
27
25
23
21
19
17
15
14
300 Ft.
205
136
102
82
68
58
51
45
41
37
34
31
29
26
23
20
Calibrating the Sprayer
2. Determine the nozzle size and use the calibration chart
Always follow the chemical manufacturers label recommendations for application rate (GPA). There are five things you
will need to know to be able to figure your nozzle size and pressure setting. They are:
1. Application rate — GPA or GAL/1000 Sq. Ft.
2. Speed — MPH
3. Width — Nozzle Spacing (in inches) for broadcast boom spraying
— Spray width (in inches) for boomless nozzles
4. Spraying Pressure — Follow chemical label recommendations for pressure/droplet size requirements
5. Solution weight and conversion factor (CF)
Spraying Solutions Other than Water
Since all the tabulations are based on spraying water, which weighs 8.34 lbs. per USA gallon, conversion factors must
be used when spraying solutions which are heavier or lighter than water. To determine the proper size nozzle for the
solution to be sprayed, first multiply the desired GPM or GPA of solution by the rate conversion factor. Then use the new
converted GPM or GPA rate to select the proper size nozzle and pressure.
Example: Desired application rate is 20 GPA of 28% Nitrogen. Determine the correct nozzle size as follows:
GPA (Solution) x Conversion Factor = Converted GPA
20 GPA (28% x 1.13 = 22.6 GPA (Water), the applicator
should choose a nozzle size that will supply 22.6 GPA of
water at the desired pressure.
See the appropriate Application Chart for your boom
spraying nozzle or boomless nozzle. Using the tractor
speed, nozzle width or spray width, nozzle size being
used and desired gallons per acre (GPA), find the
pressure (psi) necessary to achieve the desired GPA.
Weight of Solution
Specific Conversion
Gravity
Factors
7.0 lbs. per gallon
.84
.92
8.0 lbs. per gallon
.96
.98
8.934 lbs. per gallon (Water)
1.00
1.00
9.0 lbs. per gallon
1.08
1.04
10.0 lbs. per gallon
1.20
1.10
10.65 lbs. per gallon (28% Nitrogen)
1.28
1.13
11.0 lbs. per gallon
1.32
1.15
12.0 lbs. per gallon
14.0 lbs. per gallon
1.44
1.68
1.20
1.30
Example for traditional boom sprayer: Assume you have found your tractor speed to be 6 MPH, your nozzle spacing
is 20”, and you want to spray 15 GPA and your sprayer has blue AIXR11003VP nozzles. Upon looking at the application
chart, you will find that you should set the sprayer’s pressure at about 40 psi in order to apply about 15 GPA.
Example for boomless sprayer: Assume you have found your tractor speed to be 5 MPH, your nozzle will cover 216
inches (18 Ft) mounted 48” height above the target spray zone, and you will want to spray 15 GPA and your sprayer has
yellow XT024 nozzles. Upon looking at the application chart, you will find that you should set the sprayer’s pressure at
about 50 psi in order to apply about 15 GPA.
Useful Formulas
GPM
=
(Per Nozzle)
GPA x MPH x W
5,940
GPM
=
(Per Nozzle)
GAL/1000 Sq. Ft. x MPH x W
136
GPM — Gallons Per Minute
GPA — Gallons Per Acre
GAL/1000 Sq. Ft. — Gallons Per 1000 Square Feet
MPH — Miles Per Hour
W
— Nozzle Spacing (in inches) for broadcast spraying
— Spray width (in inches) for single nozzle,
Band spraying or Boomless spraying
Page 9
Calibrating the Sprayer
3. Adjusting the Sprayer Pressure
Once you have found the correct pressure (psi) setting, you must now adjust the sprayer to that pressure setting. Before
you adjust the sprayer’s pressure, it is important to follow these steps:
1. Make sure the sprayer tank is at least half full of clean water and the tank supply shutoff valve to the pump is open
2. Make sure the pressure relief valve is backed out so at least 4 threads are showing. If not, loosen the jam nut and
screw the knob out until at least 4 threads can be seen
3. Make sure the valves to the agitator are open
4. With the booms on, idle tractor and engage the tractor PTO to start the pump. Slowly increase tractor RPM, paying
attention to the sprayer pressure gauge. (Do NOT spike the sprayer pressure gauge). If you over pressurize the
spray system you can damage the pressure gauge and sprayer plumbing. Increase the tractor’s RPM until you reach
RPM that was used to set the tractor’s speed
5. Adjust the pressure relief valve to reach your desired psi for your speed and GPA. This is achieved by loosening the
jam nut on the pressure relief valve and screwing the knob in to increase pressure and out to decrease pressure.
Once you have reached your desired pressure, tighten the jam nut to lock the pressure control knob. If you can not
achieve enough pressure, slowly close the agitation valve.
You have successfully calibrated the sprayer.
PISTON TYPE PRESSURE RELIEF/REGULATING VALVE
Bypasses excess liquid. Adjustable to maintain control of line pressure at any pressure within the valve operating range.
Selected pressure setting firmly held in place by locknut. Extra large passages to handle large flows.






Polypropylene with stainless steel spring
Excellent chemical resistance
EPDM O-Rings
For pressure to 150 p.s.i.
1/4” port for pressure gauge
3/4” NPT (M) inlet & (F) outlet connections
Page 10
Calibrating the Sprayer
Calibration Chart
There are many different sizes and styles of spray tips available to meet your spraying needs. If you need further information, please contact an Ag Spray Service Center for assistance.
Please Note: Flow rates are calculated using fresh water.
Always remember to double check application rates.
Boomless Nozzle Application Charts
Hypro Boom X Tender
Boomless Nozzles
NOTE: Application rates are based on overall swath widths listed at 48” height. Refer to operating instructions if using a different swath.
HAMILTON BOOMLESS NOZZLES
Operating Data for 1800 Nozzles
Gallons per Acre
Orifice
GPM Swath
PSI
No.
180° 180° 3 MPH 4 MPH 5 MPH 8 MPH 10 MPH
30
1.7
44'
6.4
4.8
3.8
40
2.0
46'
7.2
5.4
4.3
#5
50
2.2
48'
7.6
5.7
4.5
60
2.4
50'
7.9
5.9
4.8
30
3.7
50'
12.2
9.2
7.3
40
4.2
50'
13.9
10.4
8.3
#10
50
4.6
52'
14.6
10.9
8.8
60
5.0
52'
15.8
11.9
9.5
30
5.1
54'
15.6
11.6
9.3
40
5.9
54'
18.0
13.5
10.8
#20
50
6.7
56'
19.7
14.8
11.8
60
7.1
58'
20.2
15.1
12.1
NOTE: 90° nozzles have the same GPA, but 1/2 GPM and swath
2.4
2.7
2.9
3.0
4.6
5.2
5.5
5.9
5.8
6.8
7.4
7.6
1.9
2.2
2.3
2.4
3.7
4.2
4.4
4.8
4.7
5.4
5.9
6.1
Page 11
Calibrating the Sprayer
BROADCAST & TURF APPLICATION CHART—20” SPACING
Nozzle
Size
01
015
02
025
03
035
04
05
06
08
010
015
Page 12
Pressure
(PSI)
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
15
30
40
60
80
100
115
Gallons per Acre
20-inch Nozzle Spacing
Flow
Rate
(GPM)
0.06
0.09
0.10
0.12
0.14
0.16
0.17
0.09
0.13
0.15
0.18
0.21
0.24
0.25
0.12
0.17
0.20
0.24
0.28
0.32
0.34
0.15
0.22
0.25
0.31
0.35
0.40
0.42
0.18
0.26
0.30
0.37
0.42
0.47
0.51
0.21
0.30
0.35
0.43
0.49
0.55
0.59
0.24
0.35
0.40
0.49
0.57
0.63
0.68
0.31
0.43
0.50
0.61
0.71
0.79
0.85
0.37
0.52
0.60
0.73
0.85
0.95
1.02
0.49
0.69
0.80
0.98
1.13
1.26
1.36
0.61
0.87
1.00
1.22
1.41
1.58
1.70
0.92
1.30
1.50
1.84
2.12
2.37
2.54
GAL/1000 Sq. Ft.
20-inch Nozzle Spacing
MPH
MPH
4
5
6
7
8
10
12
14
16
18
20
2
3
4
5
4.5
6.7
7.4
8.9
10.4
11.9
12.6
6.7
9.7
11.1
13.4
15.6
17.8
18.6
8.9
12.6
14.9
17.8
20.8
23.8
25.2
11.1
16.3
18.6
23.0
26.0
29.7
31.2
13.4
19.3
22.3
27.5
31.2
34.9
37.9
15.6
22.3
26.0
31.9
36.4
40.8
43.8
17.8
26.0
29.7
36.4
42.3
46.8
50.5
23.0
31.9
37.1
45.3
52.7
58.7
63.1
27.5
38.6
44.6
54.2
63.1
70.5
75.7
36.4
51.2
59.4
72.8
83.9
93.6
101.0
45.3
64.6
74.3
90.6
104.7
117.3
126.2
68.3
96.5
111.4
136.6
157.4
176.0
188.6
3.6
5.3
5.9
7.1
8.3
9.5
10.1
5.3
7.7
8.9
10.7
12.5
14.3
14.9
7.1
10.1
11.9
14.3
16.6
19.0
20.2
8.9
13.1
14.9
18.4
20.8
23.8
24.9
10.7
15.4
17.8
22.0
24.9
27.9
30.3
12.5
17.8
20.8
25.5
29.1
32.7
35.0
14.3
20.8
23.8
29.1
33.9
37.4
40.4
18.4
25.5
29.7
36.2
42.2
46.9
50.5
22.0
30.9
35.6
43.4
50.5
56.4
60.6
29.1
41.0
47.5
58.2
67.1
74.8
80.8
36.2
51.7
59.4
72.5
83.8
93.9
101.0
54.6
77.2
89.1
109.3
125.9
140.8
150.9
3.0
4.5
5.0
5.9
6.9
7.9
8.4
4.5
6.4
7.4
8.9
10.4
11.9
12.4
5.9
8.4
9.9
11.9
13.9
15.8
16.8
7.4
10.9
12.4
15.3
17.3
19.8
20.8
8.9
12.9
14.9
18.3
20.8
23.3
25.2
10.4
14.9
17.3
21.3
24.3
27.2
29.2
11.9
17.3
19.8
24.3
28.2
31.2
33.9
15.3
21.3
24.8
30.2
35.1
39.1
42.1
18.3
25.7
29.7
36.1
42.1
47.0
50.5
24.3
34.2
39.6
48.5
55.9
62.4
67.3
30.2
43.1
49.5
60.4
69.8
78.2
84.2
45.5
64.4
74.3
91.1
104.9
117.3
125.7
2.5
3.8
4.2
5.1
5.9
6.8
7.2
3.8
5.5
6.4
7.6
8.9
10.2
10.6
5.1
7.2
8.5
10.2
11.9
13.6
14.4
6.4
9.3
10.6
13.2
14.9
17.0
17.8
7.6
11.0
12.7
15.7
17.8
19.9
21.6
8.9
12.7
14.9
18.2
20.8
23.3
25.0
10.2
14.9
17.0
20.8
24.2
26.7
28.9
13.2
18.2
21.2
25.9
30.1
33.5
36.1
15.7
22.1
25.5
31.0
36.1
40.3
43.3
20.8
29.3
33.9
41.6
47.9
53.5
57.7
25.9
36.9
42.4
51.8
59.8
67.0
72.1
39.0
55.2
63.6
78.1
89.9
100.6
107.8
2.2
3.3
3.7
4.5
5.2
5.9
6.3
3.3
4.8
5.6
6.7
7.8
8.9
9.3
4.5
6.3
7.4
8.9
10.4
11.9
12.6
5.6
8.2
9.3
11.5
13.0
14.9
15.6
6.7
9.7
11.1
13.7
15.6
17.4
18.9
7.8
11.1
13.0
16.0
18.2
20.4
21.9
8.9
13.0
14.9
18.2
21.2
23.4
25.2
11.5
16.0
18.6
22.6
26.4
29.3
31.6
13.7
19.3
22.3
27.1
31.6
35.3
37.9
18.2
25.6
29.7
36.4
42.0
46.8
50.5
22.6
32.3
37.1
45.3
52.3
58.7
63.1
34.2
48.3
55.7
68.3
78.7
88.0
94.3
1.8
2.7
3.0
3.6
4.2
4.8
5.0
2.7
3.9
4.5
5.3
6.2
7.1
7.4
3.6
5.0
5.9
7.1
8.3
9.5
10.1
4.5
6.5
7.4
9.2
10.4
11.9
12.5
5.3
7.7
8.9
11.0
12.5
14.0
15.1
6.2
8.9
10.4
12.8
14.6
16.3
17.5
7.1
10.4
11.9
14.6
16.9
18.7
20.2
9.2
12.8
14.9
18.1
21.1
23.5
25.2
11.0
15.4
17.8
21.7
25.2
28.2
30.3
14.6
20.5
23.8
29.1
33.6
37.4
40.4
18.1
25.8
29.7
36.2
41.9
46.9
0.5
27.3
38.6
44.6
54.6
63.0
70.4
75.4
1.5
2.2
2.5
3.0
3.5
4.0
4.2
2.2
3.2
3.7
4.5
5.2
5.9
6.2
3.0
4.2
5.0
5.9
6.9
7.9
8.4
3.7
5.4
6.2
7.7
8.7
9.9
10.4
4.5
6.4
7.4
9.2
10.4
11.6
12.6
5.2
7.4
8.7
10.6
12.1
13.6
14.6
5.9
8.7
9.9
12.1
14.1
15.6
16.8
7.7
10.6
12.4
15.1
17.6
19.6
21.0
9.2
12.9
14.9
18.1
21.0
23.5
25.2
12.1
17.1
19.8
24.3
28.0
31.2
33.7
15.1
21.5
24.8
30.2
34.9
39.1
42.1
22.8
32.2
37.1
45.5
52.5
58.7
62.9
1.3
1.9
2.1
2.5
3.0
3.4
3.6
1.9
2.8
3.2
3.8
4.5
5.1
5.3
2.5
3.6
4.2
5.1
5.9
6.8
7.2
3.2
4.7
5.3
6.6
7.4
8.5
8.9
3.8
5.5
6.4
7.8
8.9
10.0
10.8
4.5
6.4
7.4
9.1
10.4
11.7
12.5
5.1
7.4
8.5
10.4
12.1
13.4
14.4
6.6
9.1
10.6
12.9
15.1
16.8
18.0
7.8
11.0
12.7
15.5
18.0
20.2
21.6
10.4
14.6
17.0
20.8
24.0
26.7
28.9
12.9
18.5
21.2
25.9
29.9
33.5
36.1
19.5
27.6
31.8
39.0
45.0
50.3
53.9
1.1
1.7
1.9
2.2
2.6
3.0
3.2
1.7
2.4
2.8
3.3
3.9
4.5
4.6
2.2
3.2
3.7
4.5
5.2
5.9
6.3
2.8
4.1
4.6
5.8
6.5
7.4
7.8
3.3
4.8
5.6
6.9
7.8
8.7
9.5
3.9
5.6
6.5
8.0
9.1
10.2
11.0
4.5
6.5
7.4
9.1
10.6
11.7
12.6
5.8
8.0
9.3
11.3
13.2
14.7
15.8
6.9
9.7
11.1
13.6
15.8
17.6
18.9
9.1
12.8
14.9
18.2
21.0
23.4
25.2
11.3
16.1
18.6
22.6
26.2
29.3
31.6
17.1
24.1
27.8
34.2
39.4
44.0
47.1
1.0
1.5
1.7
2.0
2.3
2.6
2.8
1.5
2.1
2.5
3.0
3.5
4.0
4.1
2.0
2.8
3.3
4.0
4.6
5.3
5.6
2.5
3.6
4.1
5.1
5.8
6.6
6.9
3.0
4.3
5.0
6.1
6.9
7.8
8.4
3.5
5.0
5.8
7.1
8.1
9.1
9.7
4.0
5.8
6.6
8.1
9.4
10.4
11.2
5.1
7.1
8.3
10.1
11.7
13.0
14.0
6.1
8.6
9.9
12.0
14.0
15.7
16.8
8.1
11.4
13.2
16.2
18.6
20.8
22.4
10.1
14.4
16.5
20.1
23.3
26.1
28.1
15.2
21.5
24.8
30.4
35.0
39.1
41.9
0.9
1.3
1.5
1.8
2.1
2.4
2.5
1.3
1.9
2.2
2.7
3.1
3.6
3.7
1.8
2.5
3.0
3.6
4.2
4.8
5.0
2.2
3.3
3.7
4.6
5.2
5.9
6.2
2.7
3.9
4.5
5.5
6.2
7.0
7.6
3.1
4.5
5.2
6.4
7.3
8.2
8.8
3.6
5.2
5.9
7.3
8.5
9.4
10.1
4.6
6.4
7.4
9.1
10.5
11.7
12.6
5.5
7.7
8.9
10.8
12.6
14.1
15.1
7.3
10.2
11.9
14.6
16.8
18.7
20.2
9.1
12.9
14.9
18.1
20.9
23.5
25.2
13.7
19.3
22.3
27.3
31.5
35.2
37.7
0.20
0.31
0.34
0.41
0.48
0.55
0.58
0.31
0.44
0.51
0.61
0.72
0.82
0.85
0.41
0.58
0.68
0.82
0.95
1.09
1.16
0.51
0.75
0.85
1.06
1.19
1.36
1.43
0.61
0.89
1.02
1.26
1.43
1.60
1.74
0.72
1.02
1.19
1.47
1.67
1.88
2.01
0.82
1.19
1.36
1.67
1.94
2.15
2.32
1.06
1.47
1.71
2.08
2.42
2.69
2.90
1.26
1.77
2.05
2.49
2.90
3.24
3.48
1.67
2.35
2.73
3.34
3.85
4.30
4.64
2.08
2.97
3.41
4.16
4.81
5.39
5.80
3.14
4.43
5.12
6.27
7.23
8.08
8.66
0.14
0.20
0.23
0.27
0.32
0.36
0.39
0.20
0.30
0.34
0.41
0.48
0.55
0.57
0.27
0.39
0.45
0.55
0.64
0.73
0.77
0.34
0.50
0.57
0.70
0.80
0.91
0.95
0.41
0.59
0.68
0.84
0.95
1.07
1.16
0.48
0.68
0.80
0.98
1.11
1.25
1.34
0.55
0.80
0.91
1.11
1.30
1.43
1.55
0.70
0.98
1.14
1.39
1.61
1.80
1.93
0.84
1.18
1.36
1.66
1.93
2.16
2.32
1.11
1.57
1.82
2.23
2.57
2.86
3.09
1.39
1.98
2.27
2.77
3.21
3.59
3.86
2.09
2.96
3.41
4.18
4.82
5.39
5.77
1.00
0.15
0.17
0.20
0.24
0.27
0.29
0.15
0.22
0.26
0.31
0.36
0.41
0.43
0.20
0.29
0.34
0.41
0.48
0.55
0.58
0.26
0.38
0.43
0.53
0.60
0.68
0.72
0.31
0.44
0.51
0.63
0.72
0.80
0.87
0.36
0.51
0.60
0.73
0.84
0.94
1.01
0.41
0.60
0.68
0.84
0.97
1.07
1.16
0.53
0.73
0.85
1.04
1.21
1.35
1.45
0.63
0.89
1.02
1.24
1.45
1.62
1.74
0.84
1.18
1.36
1.67
1.93
2.15
2.32
1.04
1.48
1.71
2.08
2.40
2.69
2.90
1.57
2.22
2.56
3.14
3.61
4.04
4.33
0.08
0.12
0.14
0.16
0.19
0.22
0.23
0.12
0.18
0.20
0.25
0.29
0.33
0.34
0.16
0.23
0.27
0.33
0.38
0.44
0.46
0.20
0.30
0.34
0.42
0.48
0.55
0.57
0.25
0.35
0.41
0.50
0.57
0.64
0.70
0.29
0.41
0.48
0.59
0.67
0.75
0.80
0.33
0.48
0.55
0.67
0.78
0.86
0.93
0.42
0.59
0.68
0.83
0.97
1.08
1.16
0.50
0.71
0.82
1.00
1.16
1.30
1.39
0.67
0.94
1.09
1.34
1.54
1.72
1.86
0.83
1.19
1.36
1.66
1.92
2.16
2.32
1.25
1.77
2.05
2.51
2.89
3.23
3.46
Calibrating the Sprayer
KLC FieldJet Nozzles used on FSBK-1 Boom Assembly
Rate Chart: Type 1/4-KLC and Type 3/4-KLC FieldJet Nozzles
The KLC FieldJet nozzle is typically used to
spray areas not accessible with a boom
sprayer. It’s one-piece nozzle design projects
spray to both sides to form a wide swath flat
spray. The round orifice minimizes clogging.
Uniformity across the swath is not as good as
with a properly operated boom sprayer.
*Available in brass or stainless steel
(*Uniformity can be optimized by double overlapping spray swaths on successive sprayer
passes. Remember, this also doubles the
application volume.)
Tip
Number
Pipe
Connection
1/4KLC-5
1/4"
1/4KLC-9
1/4"
1/4KLC-18
1/4"
1/4KLC-36
1/4"
PSI
20
30
40
20
30
40
20
30
40
20
30
40
Capacity
(One Nozzle)
in GPM
0.71
0.87
1.00
1.27
1.56
1.80
2.55
3.12
3.60
5.09
6.24
7.20
"W"
in Feet
17
18
21
18
19
21
20
21
22
22
24
26
GPA (Gallons per Acre)
GPA (Gallons per 1000 Sq. Ft.)
3
4
5
8
3
4
5
8
MPH MPH MPH MPH MPH MPH MPH MPH
6.9
5.2
4.1
2.6
0.16
0.12
0.09
0.06
8.0
6.0
4.8
3.0
0.18
0.14
0.11
0.07
7.9
5.9
4.7
2.9
0.18
0.13
0.11
0.07
11.6
8.7
7.0
4.4
0.27
0.20
0.16
0.10
13.5
10.2
8.1
5.1
0.31
0.23
0.19
0.12
14.1
10.6
8.5
5.3
0.32
0.24
0.19
0.12
21.0
15.8
12.6
7.9
0.48
0.36
0.29
0.18
25.0
18.4
14.7
9.2
0.56
0.42
0.34
0.21
27.0
20.0
16.2
10.1
0.62
0.46
0.37
0.23
38.0
29.0
23.0
14.3
0.87
0.66
0.52
0.33
43.0
32.0
26.0
16.1
0.98
0.74
0.59
0.37
46.0
34.0
27.0
17.1
1.00
0.78
0.63
0.39
NOTE: Always double-check your application rates.
Turbo FloodJet Nozzles
used on FSBK-2 Boom Assembly
AIXR11002VP Nozzles
used on FSBK-5 & FSBK-70
Boom Assemblies
Tip Chart for TKT-VP3, TF-VP3 & 30DT3.0 Tips
Tip
No.
(Color)
3
(Gray)
Tip
No.
(Color)
3
(Gray)
Tip
No.
(Color)
3
(Gray)
Pressure Capacity
(psi)
(GPM)
10
20
30
40
.30
.42
.52
.60
Pressure Capacity
(psi)
(GPM)
10
20
30
40
.30
.42
.52
.60
Pressure Capacity
(psi)
(GPM)
10
20
30
40
.30
.42
.52
.60
Gallons Per Acre - Based on Water
1
2
3
4
5
7.5
10
MPH MPH MPH MPH MPH MPH MPH
44
22
14.9 11.1 8.9
5.9
4.5
63
31.5 20.9 15.7 12.6 8.4
6.3
76
38
26
19.3 15.4 10.3 7.7
90
45
30
22
17.8 11.8 8.9
Gallons Per 1000 Sq. Ft. - Based on Water
1
2
3
4
5
7.5
10
MPH MPH MPH MPH MPH MPH MPH
1.01
.5
.34 .254 .204 .135 .103
1.4
.72
.48
.36
.29
.19
.14
1.74 .87 .596 .44
.35 .236 .176
2.06 1.00 .688 .50 .408 .27
.20
Gallons Per Acre - Based on Water
1
2
3
4
5
7.5
10
MPH MPH MPH MPH MPH MPH MPH
.10
.05 .034 .025 .02 .013 .01
.14 .072 .048 .036 .029 .019 .014
.174 .087 .059 .044 .035 .023 .017
.206 .10 .068 .05
.04 .027 .02
Spray Tip Rate Chart (20" Spacing)
Tip
No.
AIXR11002VP
Tip
No.
AIXR11002VP
Pressure Capacity
(psi)
(GPM)
15
20
30
40
.12
.14
.17
.20
Pressure Capacity
(psi)
(GPM)
15
20
30
40
.12
.14
.17
.20
Gallons Per Acre - Based on Water
1
MPH
35.6
41.6
50.4
59.6
2
MPH
17.8
20.8
25.2
29.8
3
MPH
11.8
13.8
16.8
19.8
4
MPH
8.9
10.4
12.6
14.9
5
MPH
7.1
8.3
10.1
11.9
6
MPH
5.9
6.9
8.4
9.9
8
MPH
4.5
5.2
6.3
7.4
Gallons Per 1000 Sq. Ft. - Based on Water
1
2
MPH MPH
.41
.48
.58
.68
3
MPH
.27
.32
.39
.45
4
MPH
.20
.24
.29
.34
5
6
8
MPH MPH MPH
.16
.19
.23
.27
Page 13
Operating Instructions
Before operating the sprayer, it is important that you read this entire manual and know all the safety precautions. Always
take your time and be alert when operating your sprayer. This will allow you to safely spray without accident or interruption.
Spraying with the Boom
1. Calibrate the sprayer using the calibration instructions and application charts. This will determine what pressure to
spray at in order to achieve the desired Gallons per Acre (GPA).
2. Connect the PTO coupler and torque bar to the tractor.
3. Fill the tank with some water in order to set the pressure and test for leaks.
4. Prepare the sprayer for spraying. Open the ball valve on the suction line, make sure the boom valves are off and
make sure the spray gun is closed (if applicable).
5. Start the tractor and engage the pump. The tractor should be running at the RPM rate determined when you calibrated your sprayer. Ensure that the pump is primed and that there are no leaks in any of the lines.
6. Using the relief valve (manual controls), adjust the sprayers pressure to the pressure rating found when you calibrated your sprayer. You may need to readjust the pressure when you open the boom control valves.
7. You may now fill the tank with the amount of water and chemicals recommended by the chemical manufacturer.
Before filling the tank make sure the pump is disengaged.
8. After filling the tank, engage the pump and allow an ample amount of time for the bypass (return) line to mix (agitate)
the water and chemicals. Note: See chemical instructions for necessary agitation time. You are now ready to begin
spraying.
9. Upon arriving at the spraying location, unfold booms (if applicable), engage pump, open the boom control valve and
make sure the pressure setting is correct. While spraying always remember to maintain constant level of speed and
RPM (rates found when calibrated).
Spraying with the Spray Gun
1. Connect the pump’s PTO coupler and torque bar.
2. Fill the tank with some water in order to set the pressure and test for leaks.
3. Make sure the spray gun is closed and the booms are off.
4. Start the tractor and engage the pump. Ensure that the pump is primed and that there are no leaks in any of the
lines.
5. Adjust the sprayer’s pressure using the relief valve to your desired setting. When you open the spray gun, you may
need to readjust the pressure.
6. You may now fill the tank with the amount of water and chemicals recommended by the chemical manufacturer. Before filling the tank make sure the pump is disengaged.
7. After filling the tank, engage the pump and allow an ample amount of time to mix the water and chemicals.
Note: See chemical instructions for necessary agitation time. You are now ready to begin spraying.
8. Upon arriving at the spraying location, engage the pump and make sure the pressure setting is correct. Adjust the
gun to the desired spray pattern when spraying.
Page 14
Maintenance Instructions
Routine Maintenance
It is very important to perform routine maintenance on your sprayer before and after each use. Good maintenance practices will help to guard against sprayer breakdowns or accidents.
1. It is recommended to perform a visual and physical inspection for any worn parts, loose bolts or other visible problems. Make all necessary repairs before spraying. Please contact an authorized Ag Spray dealer to order parts or to
receive technical help.
2. After each use, it is important to rinse the sprayer and all components by running a good quality tank cleaner (Tank
Neutralizer and Cleaner) through the system (if no tank cleaner is available, you may substitute a good grade of dish
soap for this step. Turn pump on and circulate through the sprayer for 15 minutes and then spray out through boom
and handgun nozzles. Refill sprayer part way with clean fresh water and repeat. Rinsing the sprayer after use will
greatly improve the life of the pump and other components.
3. Failure to properly rinse the sprayer and all components after each use, will void the manufacturer’s
warranty. Note: All rinsates must be sprayed in field
according to chemical regulations!
Cap
4. The screen of the in-line filter on the suction line should
be taken out and rinsed. Note: Be careful not to lose
the gasket in the filter bowl. The filter will leak without
this gasket.
Screen
Gasket
Bowl
5. Tip strainer (if applicable), should also be taken out and
rinsed after each use. Tips strainers are small screens
that are located behind each spray nozzle on the boom.
6. The nylon straps are to be inserted in and out of the
slots in the buckle, as shown. Be sure the straps are
snug before tightening the hook bolts. In most cases, it
will be necessary to re-tighten the straps as the tank
settles into the saddle.
Strap/Buckle Detail
Strap Attachment to a “Bent” Buckle
Page 15
Maintenance Instructions
Pump Maintenance
1. Follow all pump safety precautions and warnings. Following these guidelines will help to ensure many years of
smooth and trouble-free service.
2. Flush the pump, as directed in routine maintenance, after every use. It is also very important to winterize your pump
to prevent freezing and corrosion. Please see Winterizing your Sprayer section below for instructions.
3. After many years of use, you may find that your pump is leaking or has experienced a decrease in performance. You
may need to change the seals and rollers. Contact an authorized Ag Spray Dealer for parts and technical support.
Winterizing your Sprayer
It is essential that you winterize your sprayer to avoid damage and to allow for optimal performance. The winterization
process should be undertaken before freezing conditions and/or after each season of use. Failure to winterize your
sprayer will void the manufacturer’s warranty.
1. Verify that the tank is empty and rinsed out. Pour 1-2 gallons of RV nontoxic antifreeze into the tank. It is not recommended to use engine antifreeze. Engine antifreeze can be harmful to humans, animals, crops and the environment.
2. Engage the pump and spray with the boom and spray gun (if applicable). Make sure that the antifreeze has been
pumped through the entire system, including all spray nozzles.
3. See pump manufacturers operators manual for proper winter storage of your sprayer pump.
4. Before spraying in the spring, it is recommended to flush the sprayer with fresh water to cleanse it of the antifreeze
and any other buildup. It would also be beneficial to do a thorough inspection of all sprayer components before
spraying.
Page 16
55 Gallon 3-PT Component Breakdown & Parts List
SAS-55-3PT-KIT-GREEN
SAS-55-3PT-KIT-BLACK
Shown for reference ONLY
Page 17
Component Breakdown & Parts List
Boom Buster Kit
w/XT024 Nozzles
Assembly
#5278207
* Approx. Length of all hoses combined
Rooster Kit
w/#10 Hamilton Nozzle
#5278206
* Approx. Length of all hoses combined
Page 18
Component Breakdown & Parts List
Model: FSBK-1 (5301139)
(Single Nozzle (Boomless) Boom Assembly
w/Mounting Brackets)
(Existing) Boom Mount Brackets
Model: FSBK-2
(5300975)
(Existing) Boom Mount Brackets
(2-Nozzle Boom Kit w/7’ Coverage)
Nozzle
Assembly
1/2” to 3/8” Conversion Kit (#5277926)
If your existing sprayer has a 1/2” I.D. hose supplying your original boom and you now have a boom with 3/8” I.D. hose, this conversion kit allows you to easily convert your supply line to fit onto the 3/8” I.D. hose of your new boom.
Slip the hose mender’s 1/2” barb (larger side) into your existing 1/2” feeder hose and clamp in place with (existing) original hose
clamp. Slip the (included) 3/8” hose (5-1/2” long) onto the 3/8” barb of the hose mender and clamp in place with one of the supplied
hose clamps.
Now attach the open end of the hose onto the fitting on your boom which accepts the feeder line hose. Make sure you place the
hose clamp onto that hose prior to attaching it to your boom.
Page 19
Component Breakdown & Parts List
See Hinge Detail
Opposite side has typical
hardware setup
Model: FSBK-5
(5300976)
(5-Nozzle Boom Kit
w/100” Coverage)
Nozzle Assembly
Clamp
Hinge Detail
ELL
TEE
CROSS
See Hinge Detail
Opposite side has typical hardware setup
Model: FSBK-70
(5301100)
(7-Nozzle Boom Kit
w/140” Coverage)
Page 20
Component Breakdown & Parts List
Model: FSBK-3025BL
(5301289)
(Boomless Boom Kit
w/30’ Coverage)
End Nozzle
Assembly
5275122
Center Nozzle
Assembly
5275123
Page 21
Component Breakdown & Parts List
End Nozzle Assembly Procedure
For Boomless “Wet”Boom
Assembled
End Nozzle
1. Start by sliding Item 4, 3, 2 onto the boom tube
(Item 1) as shown, leaving about 1/2” to 3/4”
between the end of the boom tube and make sure
the “Long” portion of Item 3 is facing the nozzle
end.
2. Slide the (complete) end nozzle assembly onto the
stainless steel boom tube, with a somewhat
“twisting” motion, so that the end face of the boom
tube “butts” up against the surface face inside the
nozzle body.
3. Now push the “compression olive” (Item 3) against
o-ring (Item 2) and slide (both) into the nozzle body
opening firmly.
4. Firmly tighten flynut (Item 4) onto threads of
nozzle body.
5. Repeat for other side.
End Nozzle Information
“On/Off” Valve Positions
This nozzle mounting stem
Has a ratcheting motion.
** Each “click” of the ratcheting motion is approx. 15° **
Valve “Open”
Valve “Closed”
15°
For proper/optimal spray coverage,
The nozzle must be at a 15° angle
The 15° angle shown will prevent the outer
Nozzles from overlapping with the center nozzle.
Service Position
On/Off Valve Knob
Eliminate line pressure, then pull out
to check diaphragm condition.
Note: The check valve & diaphragm can fall out during transport, if the
knob is not turned to the “ON” or “OFF” position.
Page 22
Component Breakdown & Parts List
SAS3PT-409-Kit
Deluxe Handgun Kit
w/25’ Hose
#5278156
SAS3PT-411-Kit
Heavy Duty Handgun Kit
w/25’ Hose
#5276813
Page 23
6500C Component Breakdown & Parts List
Cast Iron 6-Roller Pump Assembly
#5271706 (Hypro #6500C)
* = Available ONLY in Repair Parts Kit #7771795 (3430-0380)
6500C-Pump Kit
#5276934
Page 24
6500N Component Breakdown & Parts List
Ni-Resist 6-Roller Pump Assembly
#5271712 (Hypro #6500N)
* = Available ONLY in Repair Parts Kit #7771795 (3430-0380)
6500N-Pump Kit
#5276976
Page 25
6500XL Component Breakdown & Parts List
Silver Cast 6-Roller Pump Assembly
#5273024 (Hypro #6500XL)
* = Available ONLY in Repair Parts Kit #7771795 (3430-0380)
6500XL-Pump Kit
#5276977
Page 26
Warranty
LIMITED WARRANTY FOR NEW AG SPRAY EQUIPMENT
WHO MAY USE THIS LIMITED WARRANTY. This limited warranty (the “Limited Warranty”) is provided by Ag Spray Equipment to the original purchaser (“you”) of the Equipment (as defined below) from Ag Spray Equipment or one of Ag Spray Equipment’s authorized dealers. This Limited
Warranty does not apply to any subsequent owner or other transferee of the Equipment. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
WHAT THIS LIMITED WARRANTY COVERS AND FOR HOW LONG. Ag Spray Equipment warrants that any new Equipment will be free from defects
in material and workmanship for a period of one (1) year after delivery of the Equipment to you (the “Warranty Period”). The Warranty Period is
not extended if Ag Spray Equipment repairs or replaces the Equipment.
WHAT IS NOT COVERED BY THIS LIMITED WARRANTY. This Limited Warranty does not apply to: (1) used Equipment; (2) any Equipment that has
been altered, changed, repaired or treated since its delivery to you, other than by Ag Spray Equipment or its authorized dealers; (3) damage or
depreciation due to normal wear and tear; (4) defects or damage due to failure to follow Ag Spray Equipment’s operator’s manual, specifications
or other written instructions, or improper storage, operation, maintenance, application or installation of parts; (5) defects or damage due to misuse, accident or neglect, “acts of God” or other events beyond Ag Spray Equipment’s reasonable control; (6) accessories, attachments, tools or
parts that were not manufactured by Ag Spray Equipment, whether or not sold or operated with the Equipment; or (7) rubber parts, such as tires,
hoses and grommets.
HOW TO OBTAIN WARRANTY SERVICE. To obtain warranty service under this Limited Warranty, you must (1) provide written notice to Ag Spray
Equipment of the defect during the Warranty Period and within thirty (30) days after the defect becomes apparent or the repair becomes necessary, at the following address: Ag Spray Equipment, 800 Stevens Port Drive, Suite DD836, Dakota Dunes,SD 57049; and (2) make the Equipment
available to Ag Spray Equipment or an authorized dealer within a reasonable period of time. For more information about this Limited Warranty,
please call: 800-274-1025 or your local Ag Spray location.
WHAT REMEDIES ARE AVAILABLE UNDER THIS LIMITED WARRANTY. If the conditions set forth above are fulfilled and the Equipment or any part
thereof is found to be defective, Ag Spray Equipment shall, at its own cost, and at its option, either repair or replace the defective Equipment or
part. Ag Spray Equipment will pay for shipping and handling fees to return the repaired or replacement Equipment or part to you.
LIMITATION OF IMPLIED WARRANTIES AND OTHER REMEDIES. THE REMEDIES DESCRIBED ABOVE ARE YOUR SOLE AND EXCLUSIVE REMEDIES,
AND AG SPRAY EQUIPMENT’S SOLE LIABILITY, FOR ANY BREACH OF THIS LIMITED WARRANTY. TO THE EXTENT APPLICABLE, ANY IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE WARRANTY PERIOD, AND THE REMEDIES AVAILABLE FOR BREACH THEREOF SHALL BE LIMITED TO THE
REMEDIES AVAILABLE UNDER THIS EXPRESS LIMITED WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL AG SPRAY EQUIPMENT’S LIABILITY UNDER THIS LIMITED
WARRANTY EXCEED THE ACTUAL AMOUNT PAID BY YOU FOR THE DEFECTIVE EQUIPMENT, NOR SHALL AG SPRAY EQUIPMENT BE LIABLE, UNDER
ANY CIRCUMSTANCES, FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL OR PUNITIVE DAMAGES OR LOSSES, WHETHER DIRECT OR INDIRECT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
Page 27
BAKERSFIELD, CA
COLUMBUS, NE
DOTHAN, AL
FARGO, ND
GREENWOOD, MS
4618 SACO RD, 93308
5834 23rd ST, 68601
2401 FORRESTER RD, 36301
4350 48th AVE N, 58102
2900 BALDWIN RD, SUITE A, 38930
661.391.9081
402.564.4544
334.673.0580
701.280.2862
662.453.4524
Toll Free: 877.724.2236
F: 661.391.9085
[email protected]
Toll Free: 800.274.1025
F: 402.564.0549
[email protected]
Toll Free: 800.227.4098
F: 334.673.1974
[email protected]
Toll Free: 800.373.4084
F: 701.293.0961
[email protected]
Toll Free: 800.844.4524
F: 662.455.4442
[email protected]
HOPKINSVILLE, KY
MANKATO, MN
NEWTON, KS
OTHELLO, WA
TEMPE, AZ
3303 PEMBROKE RD, 42240
907 SOUTHBEND AVE, 56001
7000 SCHABEN CT, 67114
81 E PINE ST, 99344
8464 KYRENE RD, 85284
270.886.0296
507.377.6295
316.283.4444
509.488.6631
480.705.8047
Toll Free: 800.637.7172
F: 270.885.7392
[email protected]
Toll Free: 800.722.9376
F: 507.388.4668
[email protected]
Toll Free: 800.394.7662
F: 316.293.4646
[email protected]
Toll Free: 800.634.2026
F: 509.488.2927
[email protected]
Toll Free: 877.705-8047
F: 480.705.8048
[email protected]
Page 28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement