XPC User Guide
XPC User Guide
For the : K48
Shuttle®
XPC Installation Guide
Copyright
©2008 by Shuttle® Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a retrieval system,
translated into any language, or transmitted in any form or by any means such as electronic,
mechanical, magnetic, optical, chemical, photocopy, manual, or otherwise, without prior
written permission from Shuttle® Inc.
Other brands and product names used herein are for identification purposes only and may
be trademarks of their respective owners.
Disclaimer
Shuttle® Inc. shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
Shuttle® Inc. makes no representation or warranty regarding the contents of this ma-
nual. Information in this manual had been carefully checked for accuracy;however, no
guarantee is given as to the correctness of the contents. For continuing product improvement, Shuttle® Inc. reserves the right to revise the manual or make changes to the specifications of this product at any time without notice and obligation to any person or entity
regarding such change. The information contained in this manual is provided for general
use by customers.
This device complies to Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1.This device may not cause harmful interference.
2.This device must withstand any background interference including those that may
cause undesired operation.
Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel and Pentium are registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice
Other brand and product names used herein are for identification purposes only and
may be trademarks of their respective owners.
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace
only with the same or equivalent as recommended by Shuttle. Dispose of
used batteries according to the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION:INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
Installation Notices
Do not place this device
underneath heavy loads
or in an unstable position.
Do not use or expose this device
around magnetic fields as
magnetic interference may affect
the performance of the device.
Do not expose this device to
high levels of direct sunlight,
high-humidity or wet conditions.
Do not block the air vents
to this device or impede the
airflow in any way.
TABLE OF CONTENTS
Driver and Software Installation...............................................................................1
Motherboard Driver CD . .......................................................................................1
Install Motherboard Software ..........................................................................2
Appendix.....................................................................................................................3
Enter the BIOS........................................................................................................3
The Main Menu.......................................................................................................4
Standard CMOS Features ...............................................................................6
Advanced BIOS Features . ..............................................................................9
Advanced Chipset Features...........................................................................13
Integrated Peripherals ..................................................................................14
Power Management Setup ............................................................................18
PnP/PCI Configurations ............................................................................... 20
PC Health Status ...........................................................................................22
Frequency/Voltage Control ............................................................................23
Load Optimized Defaults ...............................................................................25
Set Supervisor/User Password .....................................................................25
Save & Exit Setup .........................................................................................26
Exit Without Saving .......................................................................................26
English
Driver and Software Installation
 Motherboard Driver CD
The CD contents attached in SK48 motherboard are subject to change
without notice. The product's specifications will depend upon the actually shipping product.
The Motherboard Driver CD contains all the motherboard drivers necessary to optimize the performance of this XPC in a Windows® OS. Install these drivers after
installing Microsoft® Windows®.
Navigation Bar Description :
Install Motherboard Drivers - Install Intel Chipset Driver,

Install Intel VGA Driver,
Install Realtek Audio Driver,
Install Marvell Gigabit LAN Driver.
 User Manuals - Install Adobe Reader 8.1,K48 Manual,K48 Quick Guide .
Link to Shuttle Website - Link to shuttle website homepage.

 Browse this CD - Allows you to see contents of this CD.
English
 Installing Motherboard Software
Insert the attached CD into your CD-ROM drive. The CD AutoRun screen should
appear. If the AutoRun screen does not appear, double click on Autorun icon in
My Computer to bring up Shuttle Mainboard Software Setup screen.
Click the “Install Motherboard Drivers“ bar. Individually install the following drivers.
Install Intel Chipset Driver
Install Intel VGA Driver
Install Realtek Audio Driver
Install Marvell Gigabit LAN Driver
Return to previous page
English
Appendix
BIOS Settings
The SK48 BIOS ROM has a built-in Setup program that allows users to modify basic
system configuration. This information is stored in battery-backed RAM so that it
retains Setup information even if the system power is turned off.
The system BIOS manages and executes variety of hardware related functions including:
System date and time
Hardware execution sequence
Power management functions
Allocation of system resources
Enter the BIOS
To enter the BIOS (Basic Input / Output System) utility, follow these steps:
Step1.
Power on the computer. The system will perform its POST (Power-On
Self Test) routine checks.
Step2.
Press the <Del> key immediately, or at the following message:
Press DEL to enter SETUP, or simultaneously press <Ctrl>,<Alt>,
<Esc> keys
1.
If you miss wordings mentioned in step2 (the message disappears
before you can respond) and you still wish to enter BIOS Setup, restart the system and try again by turning the computer OFF and ON again or by pressing the <RESET> switch located at the computer’s front-panel. You may also reboot by simultaneously pressing the <Ctrl>,<Alt>, <Del> keys simultaneously.
2. If you do not press the keys in time and system does not boot, the
screen will prompt an error message, and you will be given the
following options:
"Press F1 to Continue, DEL to Enter Setup”
Step3.
When you enter the BIOS program, the CMOS Setup Utility will display the
Main Menu, as shown in the next section.
English
The Main Menu
Once you enter the AwardBIOS(tm) CMOS Setup Utility, the Main
Menu will appear on the screen. The Main Menu allows you to select
from several setup functions and two exit choices. Use the arrow keys
to select among the items and press <Enter> to accept and enter the
sub-menu.
Note that a brief description of each highlighted selection appears at
the bottom of the screen.
Setup Items
The main menu includes the following main setup categories. Recall
that some systems may not include all entries.
Standard CMOS Features
Use this menu for basic system configuration. Advanced BIOS Features
Use this menu to set the Advanced Features available on your system. Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your system's performance. Integrated Peripherals
Use this menu to specify your settings for integrated peripherals. Power Management Setup
Use this menu to specify your power management settings.
PnP / PCI Configurations
This entry appears if your system supports PnP / PCI. English
PC Health Status
This entry displays the current system temperature, Voltage, and FAN
settings.
Frequency/Voltage Control
Use this menu to specify your settings for frequency/voltage control. Load Optimized Defaults
Use this menu to load the BIOS default values that are factory-set for
optimal system operation. While Award has designed the custom
BIOS to maximize performance, the factory has the right to change
these defaults to meet users' needs. Set Supervisor / User Password
Use this menu to change, set, or disable password protection. This allows you to limit access to the system and Setup, or only to Setup.
Save & Exit Setup
Save CMOS value changes in CMOS and exit from setup. Exit Without Saving
Abandon all CMOS value changes and exit from setup.
English

Standard CMOS Features
The items in the Standard CMOS Setup Menu are divided into several categories. Each category includes none, one or more than one
setup items. Use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each
item.
Date
<Month> <DD> <YYYY>
Set the system date. Note that the 'Day' automatically changes when
you set the date.
Time
<HH : MM : SS>
The time is converted based on the 24-hour military-time clock.
For example, 5 p.m. is 17:00:00.
IDE Channel/IDE Channel 0 Master/Slave
Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.
Halt On
Select the situation in which you want the BIOS to stop the POST process and notify you.
The choice: All Errors, No Errors, All, But Keyboard .

English
Base Memory
Displays the amount of conventional memory detected during boot up.
The choice: N/A.

Extended Memory
Displays the amount of extended memory detected during boot up.
The choice: N/A.

Total Memory
Displays the total memory available in the system.
The choice: N/A.

******************************************************
IDE Adapters
The IDE adapters control the hard disk drive. Use a separate submenu to configure each hard disk drive.
IDE HDD Auto-Detection
Press <Enter> to auto-detect HDD on this channel. If detection is
successful, it fills the remaining fields on this menu.
 Press Enter
IDE Channel/IDE Channel 0 Master/Slave
Selecting 'manual' lets you set the remaining fields on this screen and select the type of fixed disk. "User Type" will let you select the number of cylinders, heads, etc., Note: PRECOMP=65535 means NONE !
The choice: None, Auto, or Manual.

Access Mode
Choose the access mode for this hard disk.
The choice: CHS, LBA, Large, or Auto.

Capacity
Disk drive capacity (Approximated). Note that this size is usually
slightly greater than the size of a formatted disk given by a disk checking program.
Auto-Display your disk drive size.

The following options are selectable only if the 'IDE Primary
Master' item is set to 'Manual', and Access mode set to CHS.
English
Cylinder
Set the number of cylinders for this hard disk.

Min = 0, Max = 65535
Head
Set the number of read/write heads.

Min = 0, Max = 255
Precomp
Warning: Setting a value of 65535 means no hard disk.

Min = 0, Max = 65535
Landing zone
Set the Landing zone size.

Min = 0, Max = 65535
Sector
Number of sector per track.

Min = 0, Max = 255
******************************************************
English

Advanced BIOS Features
This section allows you to configure your system for basic operation. You have the opportunity to select the system's default speed, boot-up
sequence, keyboard operation, shadowing, and security.
CPU Feature
Options are in its sub-menu.
Press <Enter> to enter the sub-menu of detailed options.
Delay Prior to Thermal
This item is select Delay Prior to Thermal.
The Choice: 4Min, 8Min, 16Min or 32 Min.

Thermal Management This item is select Thermal Management . Thermal Monitor 1 (On die
throtting). Thermal Monitor 2 Ratio & VID transition ).
The Choice: Thermal Monitor 1 or Thermal Monitor 2.

TM2 Bus Ratio
Represents the frequency (bus ratio of the throttled performance statethat will be initiated when the on-diesensor gose from not hot to
hot.
The Choice: Min=0 Max=255.

CPU support TM2, item appear.
English
TM2 Bus VID
Represents the voltageof the throttled performance statethat will be
initiated when the on diesensor gose from not hot to hot.
The Choice: 0.8375V ~1.6000V.

CPU support TM2, item appear.
PPM Mode
Native mode is for fully support ACPI OS (ex.WINXP, VISTA...), SMM
mode is for legacy OS (ex. Win2K...).
The Choice: SMM Mode or Native Mode.

Limit CPUID MaxVal
Set Limit CPUID MaxVal to 3,Should Be "Disabled" for WinXp.
The Choice: Disabled or Enabled.

Some older O.S.'s (Win98,WinMe..) cannot handle a CPUID
MaxVal greater than 3. Please choose "Enabled" if you use one
of those O.S. If your O.S. is WinXP or Win2000, we suggest
you "Disabled" the item.
C1E Function
When disabled, processor can't transitions to a lower core frequency
and voltage.
The Choice: Auto or Disabled.

CPU support, item appear.
Execute Disable Bit
When disabled, forces the XD feature flag to always return 0.
The Choice: Enabled or Disabled.

CPU support, item appear.
Virtualization Technology
When enabled, a VMM can utilize the additional hardwarecapabilities
provided by Vanderpool Technology.
The Choice: Enabled or Disabled.

CPU support, item appear.
10
English
Core Multi-Processing
This item allows you to enable/disable the Core Multi-Processing.

The choice: Disabled or Enabled.
Hard Disk Boot Priority
This item allows you to select Hard Disk Book Device Priority.
Bios Write Protect
This item allows you to enable or disable the Bios Write Protect.
If you want to flash BIOS, you must set it [Disabled].
The choice: Enabled or Disabled.

Quick Power On Self Test
This item speeds up Power-On Self Test (POST) after you power on the
computer. If it is set to enabled, BIOS will shorten or skip some check
items during POST.
The choice: Enabled or Disabled.

First/Second/Third Boot Device
The BIOS attempts to load the operating system from the devices in
the sequence selected in these items.
The Choice:LS120, Hard Disk, CDROM, ZIP100, USB-FDD,

USB-ZIP,USB-CDROM, LANor Disabled .
Security Option
Select whether the password is required every time the system boots
or only when you enter setup.
System The system will not boot and access to Setup will be denied if the correct password is not entered promptly.
Setup The system will boot, but access to Setup will be denied if the
correct password is not entered promptly.
The choice: System or Setup.

To disabled security, select PASSWORD SETTING at Main
Menu, and then you will be asked to enter password. Don't
type anything and just press <Enter>; it will disable security.
Once the security is disabled, the system will boot, and you
can enter Setup freely.
11
English
HDD Security Freeze Lock
This item allows you to enable/disable the HDD Security Freeze Lock.
Enabled - prevents any external application from locking Hard drive
except for BIOS.
The choice: Enabled or Disabled.

Delay For HDD <Secs>
This item allows you to set delay for HDD<secs>.
The choice: 0~15.

Full Screen LOGO Show
This item allows you to enable/disable the Full Screen LOGO Show.

The choice: Enabled or Disabled.
12
English

Advanced Chipset Features
This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
access to system memory resources, such as DRAM and the external
cache. It also coordinates communications between the conventional
ISA bus and the PCI bus. It states that these items should never need
to be altered.
The default settings have been chosen because they provide the best
operating conditions for your system. If you discovered that data was
being lost while using your system, you might consider making any
changes.
On-Chip Frame Buffer Size
This item allows you to set the onboard VGA share memory size.
The Choice: 1MB or 8MB.

When use On-chip VGA, On-Chip Frame Buffer Size item appear.
DVMT Mode
This item allows you to set the DVMT Version.
The Choice: DVMT, BOTH or FIXED.

When use On-chip VGA, DVMT Mode item appear.
DVMT/FIXED Memory Size
This item allows you to set the DVMT/FIXED Memory Size.
The Choice: 64MB, 128MB or 224MB.

When use On-chip VGA, DVMT/FIXED Memory Size
item appear.
13
English

Integrated Peripherals
On-Chip IDE Device
Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
IDE HDD Block Mode
If your IDE hard disk drive supports block mode (most new drives do),
select Enabled to automatic detect the optimal number of block read
and writes per sector that the drive can support and improves the
speed of access to IDE devices.
The choice: Enabled, or Disabled.

On-Chip Primary PCI IDE
Use these items to enable or disable the PCI IDE channels that are
integrated on the mainboard.
The choice: Enabled or Disabled.

IDE Primary Master/Slave PIO
Each IDE channel supports a master device and a slave device. These
four items let you assign which kind of PIO ( Programmed Input / Output ) is used by IDE devices. Choose Auto to let the system auto detect
which PIO mode is best or select a PIO mode from 0-4.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, or Mode 4.

14
English
IDE Primary Master/Slave UDMA
Each IDE channel supports a master device and a slave device. This
mainboard supports UltraDMA technology, which provides faster access to IDE devices.
If you install a device that supports UltraDMA, change the appropriate
item on this list to Auto. You may have to install the UltraDMA driver
supplied with this mainboard in order to use an UltraDMA device.
The Choice: Auto or Disabled.

********** On -Chip Serial ATA Setting **********
On-Chip Serial ATA
Enhanced Mode
SATA PORT Speed Settings
This item allows you to set the SATA PORT Speed.
The choice: Disabled, Force GEN I, or Force GEN II.

Onboard Device
Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
High Definition Audio
This item allows you to set the High Definition Audio.
The choice: Enabled or Disabled.

SuperIO Device
Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
Onboard Serial Port 1
This option is used to assign the I/O address and interrupt request
( IRQ ) for the onboard serial port 1 ( COM1 ).
The choice:Disabled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,

or Auto.
15
English
Onboard Parallel Port
This item allows you to determine onboard parallel port controller I/O address and interrupt request ( IRQ ).
The choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, or Disabled.

Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.
The choice: SPP, EPP, ECP, or ECP+EPP.

ECP Mode Use DMA
When the onboard parallel is set to ECP mode, the parallel port can
use DMA3 or DMA1.
The choice: 1 or 3.

USB Device Setting
Option are in its sub-menu.
Press<Enter>to enter the sub-menu of detailed options.
USB 2.0 Controller
Enable or Disable Universal Host Controller Interfacefor Universal Serial Bus.

The choice: Enabled or Disabled.
USB Operation Mode
Auto decide USB device operation mode.
High speed:If USB device was high speed device, then it operated on
high speed mode.If USB device was full/low speed device,
then it operated on full/low speed mode.
Full/Low Speed:All of USB device operated on full/low speed mode.

The choice: High speed or Full/Low Speed.
USB Storage Function
Enable or Disable Legacy support of USB USB Mass Storage.

The choice: Enabled or Disabled.
16
English
*** USB Mass Storage Device Boot Setting ***
UFDDA USB Floppy
UFDDB USB Floppy
No Device
Auto: According to contents of USB MSD decide boot up type.
FDD Mode: The USB MSD always boot up as floppy disk.
HDD Mode: The USB MSD always boot up as hard disk.

The choice: Auto mode, FDD mode or HDD mode.
17
English

Power Management Setup
The Power Management Setup allows you to configure your system to
most effectively save energy while operating in a manner consistent
with your computer usage.
ACPI Suspend Type
This item allows you to select sleep state when suspend.
The choice: S1(POS) or S3(STR).

Run VGABIOS if S3 Resume(Auto)
This item allows the system to initialize the VGA BIOS from S3(Suspend to RAM) sleep state.
The choice: Auto, Yes or No.

Soft-Off by PWR-BTTN
Under ACPI you can create a software power down. In a software
power down, the system can be resumed by Wake UP Alarms. This
item lets you install a software power down that is controlled by the
power button on your system. If the item is set to Instant-Off, then the
power button causes a software power down. If the item is set to Delay4 Sec. then you have to hold the power button down for 4 seconds
to cause a software power down.
The choice: Instant-Off or Delay 4 Sec.

Wake-Up by Onboard LAN
This item allows you to set the Wake-Up by Onboard LAN.
The choice: Enabled or Disabled.

18
English
Power On by Ring
This item determine the system will resume by activating of modem
ring.
The choice: Enabled or Disabled.

Resume by Alarm
When this item enabled, your can set the date (day of the month) and
time to turn on your system.
The choice: Disabled or Enabled.

Date(of Month) Alarm
This item selects the alarm Date (day of the month).
Key in a DEC number: Min=0, Max=31.

Time(hh : mm : ss) Alarm
This item selects the alarm Time.
[hh] Key in a DEC number: Min=0, Max=23.
[mm/ss]Key in a DEC number: Min=0, Max=59.
PS2 Keyboard Power ON
This item allows you to set the PS2 Keyboard Wake Up system from
S3/S4/S5.
The choice: Disabled, Password, or Hot Key.

KB Power ON Password
This item allows you to set the KB Power On Password.
Press" Enter" to set Password.

Hot Key Power On
This item allows you to set the Hot Key Power On.
The choice: Any Key, Ctrl-F1~Ctrl-F12.

PS2 Mouse Power ON
This item allows you to set the PS2 Mouse Wake Up system from
S3/S4/S5.
The choice: Disabled, Password, or Hot Key.

PWR-On After PWR-Fail
This item defines if the system will be rebooted after the power fails.
The choice: Off, On, Former-Sts.

19
English

PnP/PCI Configurations
This section describes the configuration of PCI bus system. PCI or Personal Computer Interconnection is a system which allows I/O devices
to operate at the speed CPU itself keeps when CPU communicating
with its own special components.
This section covers some very technical items, and it is strongly recommended that only experienced users should make any changes to the
default settings.
Resource controlled By
The Award Plug-and-Play BIOS has the capacity to automatically
configure all of the boot and Plug-and-Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug-and-Play operating system such as Windows 95. The choice: Auto(ESCD) or Manual.

IRQ Resources
When resources are controlled manually, assign each system interrupt
a type, depending on the type of device using the interrupt.
IRQ3/4/5/7/10/11/12/14/15 assigned
This item allows you to determine the IRQ assigned to the ISA bus and
is not available to any PCI slot. Legacy ISA for devices is compliant
with the original PC AT bus specification; PCI/ISA PnP for devices is
compliant with the Plug-and-Play standard whether designed for PCI
or ISA bus architecture.
The choice: PCI Device or Reserved.

20
English
PCI/VGA Palette Snoop
It determines whether the MPEG ISA/VESA VGA Cards can work with
PCI/VGA or not. If you have MPEG ISA/VESA VGA Cards and PCI/
VGA Card worked, Enable this field. Otherwise, please Disable it.
The choice: Enabled or Disabled.

INT Pin1~8 Assignment
Names the interrupt request(IRQ) line assigned to a device connected
to the PCI interface on your system.
The choice: Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.

21
English

PC Health Status
CPU Fan Speed Control
Here you can set the CPU Fan Speed.

The choice:Smart Fan Mode, Ultra-Low Speed, Low Speed,
Mid Speed, or Full Speed.
DDR2 Voltage
+3.3V
+5V
+12V
ChipSet Voltage
CPU Voltage
+5VSB
Voltage Battery
System Temperature
CPU Temperature
Fan 1 Speed
Fan 2 Speed
Fan 3 Speed
22
Before manually modifying the
CPU fan setting, please make
sure fan connectors are plug
ged into the correct fan conne
ctor on the motherboard.
Warning:It is strongly recommended to disable 'Smart Fan' if you use an alternative fan to the default.
English

Frequency/Voltage Control
Spread Spectrum
This item allows you to enable or disable the spread spectrum modulation.
The choice: Disabled or Enabled.

CPU Clock Ratio Unlock
This item allows the user to adjust CPU Clock Ratio.
If CPU is unlocked, item appear.
The Choice: Disabled or Enabled.

CPU Clock Ratio
This item allows the user to adjust CPU Clock Ratio.
If CPU is unlocked, item appear.
The Choice: 6X~50X.

************** Clock *************
CPU Clock
This item allows the user to adjust CPU Host Clock.
Min: 100 Max: 333
Key in a DEC number: (Between Min and Max.)

DRAM Timing Selectable
This item allows the user to adjust DRAM Timing Selectable.
The Choice: manual or by SPD

23
English
CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Don't change this field from
the default value specified by the system designer.
The Choice: Auto,3,4,5,6.
DRAM RAS# to CAS# Delay
This field lets you insert a timing delay between the CAS and RAS
strobe signals, and you can use it when DRAM is written to, read
from, or refreshed. Faster performance is gained in high speed, more stable
performance, in low speed. This field is applied only when synchronous
DRAM is installed in the system.
The Choice: Auto,2,3,4,5,6.
DRAM RAS# Precharge
If an insufficient number of cycles is allowed for the RAS to accumulate
its charge before DRAM refresh, the refresh may be-incompleted, and the
DRAM may fail to retain data. Fast gives faster performance; and Slow
gives more stable performance. This field is applied only when synchronous DRAM is installed in the system.
The Choice: Auto,2,3,4,5,6.
Precharge dealy (tRAS)
The precharge time is the number of cycles it takes for DRAM to accumulate its charge before refresh.
The Choice: Auto or 4~15.
System Memory Frequency
This item allows you to set system Memory Frequency.
The Choice: 400MHz, 533MHz, 667MHz , 500MHz, 834MHz or Auto.
CPU N/2 Ration
This item allows you to enable/disable the CPU N/2 Ration
The choice: Disabled or Enabled.

************** Voltage *************
DDR2 Voltage Set
This item allows you to set DDR2 Voltage Set.

The choice: Auto or 1.9V,2.0V,2.1V.
24
English

Load Optimized Defaults
When you press <Enter> on this item, you will get a confirmation
dialog box with a message similar to:
Load Default Settings (Y/N) ? N
Pressing 'Y' loads the default values that are factory-set for optimal
performance system operation.

Set Supervisor/User Password
Steps to set supervisor/user password are described as follows:
New Password Setting:
1. While pressing <Enter> to set a password, a dialog box appears to
ask you enter a password.
2. Key in a new password. The password can not exceed eight characters.
3. System will request you to confirm the new password again.
4. When completed, new code takes effect.
No Password Setting:
5. If you want to delete the password, just press the <Enter> key
instead of typinga new password. Follow the procedure as ablve.
If You Forget Password:
6. If you forget your password, you must turn off the system and clear
CMOS. Please refer to the tech notes at the end of section two for more information.
25
English

Save & Exit Setup
Pressing <Enter> on this item asks for confirmation:
SAVE to CMOS and EXIT (Y/N)? Y
Pressing "Y" stores the selections made in the menus of CMOS - a special
section of memory that stays on after you turn your system off. The next
time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. After saving the values the
system is restarted again.
Exit Without Saving
Pressing <Enter> on this item asks for confirmation:
Quit Without Saving (Y/N)? N
This allows you to exit from Setup without storing in CMOS any change.
The previous selections remain in effect. This exits from the Setup utility
and restarts your computer.
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement