MDO3000 Oscilloscope Datasheet - Thurlby Thandar instrument

Mixed Domain Oscilloscopes

MDO3000 Series Datasheet

Today's integrated designs need an oscilloscope that is just as integrated such as the MDO3000 Mixed Domain Oscilloscope (MDO) Series. It is the ultimate 6-in-1 integrated oscilloscope that includes an integrated spectrum analyzer, arbitrary function generator, logic analyzer, protocol analyzer, and digital voltmeter/counter. The MDO3000 is completely customizable and fully upgradeable. Add the instruments and performance you need now - or later.

Key performance specifications

Oscilloscope

2 and 4 analog channel models

1 GHz, 500 MHz, 350 MHz, 200 MHz, 100 MHz bandwidth models

Bandwidth is upgradable (up to 1 GHz)

Up to 5 GS/s sample rate

10 M record length on all channels

>280,000 wfm/s maximum waveform capture rate

Standard passive voltage probes with 3.9 pF capacitive loading and 1 GHz, 500 MHz, or 250 MHz analog bandwidth

Spectrum Analyzer

Frequency range

Standard: 9 kHz - oscilloscope bandwidth

Optional: 9 kHz - 3 GHz

Ultra-wide capture bandwidth up to 3 GHz

Arbitrary Function Generator (Optional)

13 predefined waveform types

50 MHz waveform generation

128 k arbitrary generator record length

250 MS/s arbitrary generator sample rate

Logic Analyzer (Optional)

16 digital channels

10 M record length on all channels

121.2 ps timing resolution

Protocol Analyzer (Optional)

Serial bus support for I

2

C, SPI, RS-232/422/485/UART, USB 2.0,

CAN, LIN, FlexRay, MIL-STD-1553, and Audio standards

Digital Voltmeter (Free with product registration)

4-digit AC RMS, DC, and AC+DC RMS voltage measurements

5-digit frequency measurements

Key features

FastAcq

™

high-speed waveform capture rate finds elusive signal anomalies quickly

Wave Inspector

®

Controls provide easy navigation and automated search of waveform data

33 automated measurements and waveform histograms for simplified waveform analysis

TekVPI

®

probe interface directly supports active, differential, and current probes for automatic scaling and units

9 in. (229 mm) WVGA widescreen color display

Small footprint and lightweight – Only 5.8 in. (147 mm) deep and 9.2 lb.

(4.2 kg)

Spectral Analysis

Dedicated front-panel controls for commonly performed tasks

Automated peak markers identify frequency and amplitude of spectrum peaks

Manual markers enable non-peak measurements

Trace types include: Normal, Average, Max Hold, and Min Hold

Spectrogram display enables easy observation and insight into slowly changing RF phenomena

Automated measurements include: Channel Power, Adjacent

Channel Power Ratio (ACPR), and Occupied Bandwidth (OBW)

Arbitrary Function Generation

Generate predefined signals to quickly simulate missing devices in designs

Capture signals on analog or digital inputs, transfer to the arbitrary edit memory, and replicate out from the AFG

Add noise to any signal to easily perform margin testing www.tektronix.com 1

Datasheet

Mixed signal design and analysis

Automated triggering, decode, and search on parallel buses

Multichannel setup and hold triggering

MagniVu

™

high-speed acquisition provides 121.2 ps fine timing resolution on digital channels

Protocol Analysis

Trigger, decode and automatically search on packet-level content on most common embedded design serial bus standards.

Export protocol decode tables for use in documenting results

Digital Voltmeter and Frequency Counter

Quickly validate voltage or frequency measurements at a glance

Graphical readout provides information on stability of the measurement

Fully upgradeable

Add functionality, increase bandwidth or spectrum analyzer frequency range over time as your needs change or budget allows

Optional application support

Power analysis

Limit and mask testing

Need more performance?

Need more input frequency range on the spectrum analyzer?

Need to analyze analog, digital, and RF simultaneously?

Need more record length or a larger display?

Consider the MDO4000B Series oscilloscopes www.tektronix.com/MDO4000

Oscilloscope

At the core of the MDO3000 Series is a world-class oscilloscope, offering comprehensive tools that speed each stage of debug – from quickly discovering anomalies and capturing them, to searching your waveform record for events of interest and analyzing their characteristics and your device’s behavior.

Digital phosphor technology with FastAcq

™

speed waveform capture

high-

To debug a design problem, first you must know it exists. Every design engineer spends time looking for problems in their design, a timeconsuming and frustrating task without the right debug tools.

Digital phosphor technology provides you with fast insight into the real operation of your device. Its fast waveform capture rate – greater than

280,000 wfm/s with FastAcq – gives you a high probability of quickly seeing the infrequent problems common in digital systems: runt pulses, glitches, timing issues, and more.

To further enhance the visibility of rarely occurring events, intensity grading is used to indicate how often rare transients are occurring relative to normal signal characteristics. There are four waveform palettes available in

FastAcq acquisition mode.

The Temperature palette uses color-grading to indicate frequency of occurrence with hot colors like red/yellow indicating frequently occurring events and colder colors like blue/green indicating rarely occurring events.

The Spectral palette uses color-grading to indicate frequency of occurrence with colder colors like blue indicating frequently occurring events and hot colors like red indicating rarely occurring events.

The Normal palette uses the default channel color (like yellow for channel one) along with gray-scale to indicate frequency of occurrence where frequently occurring events are bright.

The Inverted palette uses the default channel color along with grayscale to indicate frequency of occurrence where rarely occurring events are bright.

These color palettes quickly highlight the events that over time occur more often or, in the case of infrequent anomalies, occur less often.

Infinite or variable persistence choices determine how long waveforms stay on the display, helping you to determine how often an anomaly is occurring.

► 3 GHz and 6 GHz integrated spectrum analyzers

► Simultaneous acquisition of analog, digital and RF

► 20 M record length

► 10.4 inch XGA display

2 www.tektronix.com

Mixed Domain Osciloscopes -- MDO3000 Series

Digital phosphor technology with FastAcq enables greater than 280,000 wfms/s waveform capture rate and real-time color-intensity grading.

Triggering

Discovering a device fault is only the first step. Next, you must capture the event of interest to identify root cause. To enable this, the MDO3000 contains over 125 trigger combinations providing a complete set of triggers

- including runt, logic, pulse width/glitch, setup and hold violation, serial packet, and parallel data - to help quickly locate your event of interest. And with up to a 10 M record length, you can capture many events of interest, even thousands of serial packets, in a single acquisition for further analysis while maintaining high resolution to zoom in on fine signal details.

Over 125 trigger combinations make capturing your event of interest easy.

Wave Inspector

®

waveform navigation and automated search

With long record lengths, a single acquisition can include thousands of screens of waveform data. Wave Inspector

®

, the industry’s best tool for waveform navigation and automated search, enables you to find events of interest in seconds.

Wave Inspector controls provide unprecedented efficiency in viewing, navigating, and analyzing waveform data. Zip through your long record by turning the outer pan control

(1). Get details from the beginning to end in seconds. See something of interest and want to see more details? Just turn the inner zoom control (2).

Zoom and pan

A dedicated, two-tier front-panel control provides intuitive control of both zooming and panning. The inner control adjusts the zoom factor (or zoom scale); turning it clockwise activates zoom and goes to progressively higher zoom factors, while turning it counterclockwise results in lower zoom factors and eventually turning zoom off. No longer do you need to navigate through multiple menus to adjust your zoom view. The outer control pans the zoom box across the waveform to quickly get to the portion of waveform you are interested in. The outer control also utilizes force-feedback to determine how fast to pan on the waveform. The farther you turn the outer control, the faster the zoom box moves. Pan direction is changed by simply turning the control the other way.

User marks

Press the Set Mark front-panel button to place one or more marks on the waveform. Navigating between marks is as simple as pressing the

Previous (←) and Next (→) buttons on the front panel.

Search marks

The Search button allows you to automatically search through your long acquisition looking for user-defined events. All occurrences of the event are highlighted with search marks and are easily navigated to, using the frontpanel Previous (←) and Next (→) buttons. Search types include edge, pulse width/glitch, timeout, runt, logic, setup and hold, rise/fall time, parallel bus, and I

2

C, SPI, RS-232/422/485/UART, USB 2.0, CAN, LIN, FlexRay,

MIL-STD-1553, and Audio packet content. A search mark table provides a tabular view of the events found during the automated search. Each event is shown with a time stamp, making timing measurements between events easy.

www.tektronix.com 3

Datasheet

Waveform analysis

Verifying that your prototype’s performance matches simulations and meets the project’s design goals requires analyzing its behavior. Tasks can range from simple checks of rise times and pulse widths to sophisticated power loss analysis and investigation of noise sources.

The oscilloscope offers a comprehensive set of integrated analysis tools including waveform- and screen-based cursors, automated measurements, advanced waveform math including arbitrary equation editing, FFT analysis, waveform histograms, and trend plots for visually determining how a measurement is changing over time.

Search step 1: You define what you would like to find.

Search step 2: Wave Inspector automatically searches through the record and marks each event with a hollow white triangle. You can then use the Previous and Next buttons to jump from one event to the next.

Automated measurement readouts provide repeatable, statistical views of waveform characteristics.

Search step 3: The Search Mark table provides a tabular view of each of the events found by the automated search. Each event is shown with a time stamp making timing measurements between events easy.

Each measurement has help text and graphics associated with it that help explain how the measurement is made.

Waveform histograms show visually how waveforms vary over time.

Horizontal waveform histograms are especially useful for gaining insight into how much jitter is on a clock signal, and what the distribution of that jitter is. Vertical histograms are especially useful for gaining insight into how much noise is on a signal, and what the distribution of that noise is.

Measurements taken on a waveform histogram provide analytical information about the distribution of a waveform histogram, providing insight into just how broad a distribution is, the amount of standard deviation, the mean value, etc.

4 www.tektronix.com


Waveform histogram of a rising edge showing the distribution of edge position (jitter) over time. Included are numeric measurements made on the waveform histogram data.

Video design and development

Many video engineers have remained loyal to analog oscilloscopes, believing the intensity gradations on an analog display are the only way to see certain video waveform details. The fast waveform capture rate of the

MDO3000, coupled with its intensity-graded view of the signal, provides the same information-rich display as an analog oscilloscope, but with much more detail and all the benefits of digital scopes.

Standard features such as IRE and mV graticules, holdoff by fields, video polarity, HDTV and custom (nonstandard) video triggers, and an Autoset smart enough to detect video signals, make these the easiest to use oscilloscopes on the market for video applications. And with high bandwidth, four analog inputs, and a built-in 75 Ω input termination (not available on 1 GHz models), the oscilloscope provides ample performance for analog and digital video use. There is even a video picture mode enabling you to see the picture of the video signal you are viewing – for

NTSC and PAL signals.

Viewing an NTSC full color bar signal image. Video picture mode contains automatic contrast and brightness settings as well as manual controls.

Power analysis (optional)

Ever increasing consumer demands for longer battery-life devices and for green solutions that consume less power require power-supply designers to characterize and minimize switching losses to improve efficiency. In addition, the supply’s power levels, output purity, and harmonic feedback into the power line must be characterized to comply with national and regional power quality standards. Historically, making these and many other power measurements on an oscilloscope has been a long, manual, and tedious process. The MDO3000’s optional power analysis tools greatly simplify these tasks, enabling quick, repeatable and accurate analysis of power quality, switching loss, harmonics, safe operating area (SOA), modulation, ripple, and slew rate (di/dt, dv/dt). Completely integrated into the oscilloscope, the power analysis tools provide automated, repeatable power measurements with a touch of a button.

Viewing an NTSC video signal. Notice the intensity-graded view provided by the

MDO3000's ability to represent time, amplitude, and distribution over time.

Power Quality measurement table. Automated power measurements enable quick and accurate analysis of common power parameters.

www.tektronix.com 5

Datasheet

Limit/Mask testing (optional)

A common task during the development process is characterizing the behavior of certain signals in a system. One method, called limit testing, is to compare a tested signal to a known good or "golden" version of the same signal with user-defined vertical and horizontal tolerances. Another common method, called mask testing, is to compare a tested signal to a mask, looking for where a signal under test violates the mask. The

MDO3000 Series offers both limit and mask testing capability useful for long-term signal monitoring, characterizing signals during design, or testing on a production line. Tailor a test to your specific requirements by defining test duration in number of waveforms or time, a violation threshold that must be met before considering a test a failure, counting hits along with statistical information, and actions upon violations, test failure, and test complete. Whether specifying a mask from a known good signal or from a custom mask, conducting pass/fail tests in search of waveform anomalies such as glitches has never been easier.

TekVPI

®

probe interface

The TekVPI probe interface sets the standard for ease of use in probing. In addition to the secure, reliable connection that the interface provides,

TekVPI probes feature status indicators and controls, as well as a probe menu button right on the comp box itself. This button brings up a probe menu on the oscilloscope display with all relevant settings and controls for the probe. The TekVPI interface enables direct attachment of current probes without requiring a separate power supply. TekVPI probes can be controlled remotely through USB, GPIB, or LAN, enabling more versatile solutions in ATE environments. The TekVPI inputs provide up to 25 W of power to the front panel connectors from the internal power supply.

Limit Test showing a mask created from a golden waveform and compared against a live signal. Results showing statistical information about the test are displayed.

Standard passive voltage probes

The MDO3000 Series include passive voltage probes with industry best capacitive loading of only 3.9 pF. The included TPP probes minimize the impact on devices under test and accurately deliver signals to the oscilloscope for acquisition and analysis. The following table shows which

TPP probes come standard with each MDO3000 model.

MDO3000 model

MDO3012, MDO3014,

MDO3022, MDO3024

MDO3032, MDO3034,

MDO3052, MDO3054

MDO3102, MDO3104

Included probe

TPP0250: 250 MHz, 10x passive voltage probe. One per analog channel

TPP0500B: 500 MHz, 10x passive voltage probe. One per analog channel

TPP1000: 1 GHz, 10x passive voltage probe. One per analog channel

TekVPI probe interface simplifies connecting your probes to the oscilloscope.

Remote connectivity and instrument control

Exporting data and measurements is as simple as connecting a USB cable from the oscilloscope to your PC. Key software applications –

OpenChoice

®

Desktop, and Microsoft Excel and Word toolbars – are included standard with each oscilloscope to enable fast and easy direct communication with your Windows PC.

The included OpenChoice Desktop enables fast and easy communication between the oscilloscope and your PC through USB or LAN for transferring settings, waveforms, and screen images.

The embedded e*Scope

®

capability enables fast control of the oscilloscope over a network connection through a standard web browser. Simply enter the IP address or network name of the oscilloscope and a web page will be served to the browser. Transfer and save settings, waveforms, measurements, and screen images or make live control changes to settings on the oscilloscope directly from the web browser.

6 www.tektronix.com

Mixed Domain Osciloscopes -- MDO3000 Series e*Scope in a web browser showing the display of an MDO3000. Use e*Scope to quickly document your work by saving screen images, waveforms, or setups for later use.

Spectrum Analyzer

The MDO3000 is the first oscilloscope in its class to include an integrated spectrum analyzer. Each oscilloscope includes a spectrum analyzer with a frequency range of 9 kHz up to the analog bandwidth of the instrument. The spectrum analyzer frequency range of each instrument can be upgraded from 9 kHz to 3 GHz (option MDO3SA), enabling spectral analysis on most consumer wireless standards.

Fast and accurate spectral analysis

When using the spectrum analyzer input, the MDO3000 Series display becomes a full-screen Frequency Domain view.

Key spectral parameters such as Center Frequency, Span, Reference

Level, and Resolution Bandwidth are all adjusted quickly and easily using the dedicated front-panel menus and keypad.

MDO3000 frequency domain display.

Key spectral parameters are adjusted quickly with the dedicated front-panel menus and keypad.

Intelligent, efficient markers

In a traditional spectrum analyzer, it can be a very tedious task to turn on and place enough markers to identify all your peaks of interest. The

MDO3000 Series makes this process far more efficient by automatically placing markers on peaks that indicate both the frequency and the amplitude of each peak. You can adjust the criteria that the oscilloscope uses to automatically find the peaks.

The highest amplitude peak is referred to as the reference marker and is shown in red. Marker readouts can be switched between Absolute and

Delta readouts. When Delta is selected, marker readouts show each peak's delta frequency and delta amplitude from the reference marker.

Two manual markers are also available for measuring non-peak portions of the spectrum. When enabled, the reference marker is attached to one of the manual markers, enabling delta measurements from anywhere in the spectrum. In addition to frequency and amplitude, manual marker readouts also include noise density and phase noise readouts depending on whether

Absolute or Delta readouts are selected. A "Reference Marker to Center" function instantly moves the frequency indicated by the reference marker to center frequency.

www.tektronix.com 7

Datasheet

Automated peak markers identify critical information at a glance. As shown here, the five highest amplitude peaks that meet the threshold and excursion criteria are automatically marked along with the peak's frequency and amplitude.

Spectrogram

The MDO3000 Series includes a spectrogram display which is ideal for monitoring slowly changing RF phenomena. The x-axis represents frequency, just like a typical spectrum display. However, the y-axis represents time, and color is used to indicate amplitude.

Spectrogram slices are generated by taking each spectrum and "flipping it up on its edge" so that it's one pixel row tall, and then assigning colors to each pixel based on the amplitude at that frequency. Cold colors (blue, green) are low amplitude and hotter colors (yellow, red) are higher amplitude. Each new acquisition adds another slice at the bottom of the spectrogram and the history moves up one row. When acquisitions are stopped, you can scroll back through the spectrogram to look at any individual spectrum slice.

Ultra-wide capture bandwidth

Today's wireless communications vary significantly with time, using sophisticated digital modulation schemes and, often, transmission techniques that involve bursting the output. These modulation schemes can have very wide bandwidth as well. Traditional swept or stepped spectrum analyzers are ill equipped to view these types of signals as they are only able to look at a small portion of the spectrum at any one time.

The amount of spectrum acquired in one acquisition is called the capture bandwidth. Traditional spectrum analyzers sweep or step the capture bandwidth through the desired span to build the requested image. As a result, while the spectrum analyzer is acquiring one portion of the spectrum, the event you care about may be happening in another portion of the spectrum. Most spectrum analyzers on the market today have 10 MHz capture bandwidths, sometimes with expensive options to extend that to

20, 40, or even 160 MHz in some cases.

In order to address the bandwidth requirements of modern RF, the

MDO3000 Series provides up to 3 GHz of capture bandwidth. The spectrum is generated from a single acquisition, thus guaranteeing you'll see the events you're looking for in the frequency domain.

Spectral display of a bursted communication both into a device through Zigbee at

900 MHz and out of the device through Bluetooth at 2.4 GHz, captured with a single acquisition.

Spectrum traces

The MDO3000 Series spectrum analyzer offers four different traces or views including Normal, Average, Max Hold, and Min Hold.

Spectrogram display illustrates slowly moving RF phenomena. As shown here, a signal that has multiple peaks is being monitored. As the peaks change in both frequency and amplitude over time, the changes are easily seen in the Spectrogram display.

8 www.tektronix.com

Normal, Average, Max Hold, and Min Hold spectrum traces

RF measurements

The MDO3000 Series includes three automated RF measurements -

Channel Power, Adjacent Channel Power Ratio, and Occupied Bandwidth.

When one of these RF measurements is activated, the oscilloscope automatically turns on the Average spectrum trace and sets the detection method to Average for optimal measurement results.


RF probing

Signal input methods on spectrum analyzers are typically limited to cabled connections or antennas. But with the optional TPA-N-VPI adapter, any active, 50 Ω TekVPI probe can be used with the spectrum analyzer on the

MDO3000 Series. This enables additional flexibility when hunting for noise sources and enables easier spectral analysis by using true signal browsing on a spectrum analyzer input.

In addition, an optional preamplifier accessory assists in the investigation of lower-amplitude signals. The TPA-N-PRE preamplifier provides 10 dB nominal gain across the 9 kHz – 3 GHz frequency range.

Automated Channel Power measurement

Advanced RF analysis

The MDO3000 can save the baseband I and Q data from spectrum analyzer acquisitions to a .TIQ file. These files can then be imported into

Tektronix SignalVu-PC software for general purpose modulation and pulse analysis or RSAVu for analysis of commercial wireless standards.

The optional TPA-N-VPI adapter enables any active, 50 Ω TekVPI probe to be connected to the RF input.

Arbitrary Function Generator (optional)

The MDO3000 contains an optional integrated arbitrary function generator

(option MDO3AFG), perfect for simulating sensor signals within a design or adding noise to signals to perform margin testing.

The integrated function generator provides output of predefined waveforms up to 50 MHz for sine, square, pulse, ramp/triangle, DC, noise, sin(x)/x

(Sinc), Gaussian, Lorentz, exponential rise/fall, Haversine and cardiac.

The arbitrary waveform generator provides 128 k points of record for storing waveforms from the analog input, a saved internal file location, a

USB mass storage device, or from an external PC. Once a waveform is in the edit memory of the arbitrary waveform generator, it can be modified via an on-screen editor and then replicated out of the generator. The

MDO3000 is compatible with Tektronix’ ArbExpress PC-based waveform creation and editing software, making creation of complex waveforms fast and easy. Transfer waveform files to your MDO3000 edit memory via USB or LAN or using a USB mass storage device to be output from the AFG in the oscilloscope.

www.tektronix.com 9

Datasheet

Waveform type selection in the integrated AFG.

Color-coded digital waveform display

Color-coded digital traces display ones in green and zeros in blue. This coloring is also used in the digital channel monitor. The monitor shows if signals are high, low, or are transitioning so you can see channel activity at a glance without having to clutter your display with unneeded digital waveforms.

The multiple transition detection hardware shows you a white edge on the display when the system detects multiple transitions. White edges indicate that more information is available by zooming in or acquiring at faster sampling rates. In most cases zooming in will reveal the pulse that was not viewable with the previous settings. If the white edge is still present after zooming in as far as possible, this indicates that increasing the sample rate on the next acquisition will reveal higher frequency information than the previous settings could acquire.

You can group digital waveforms and enter waveform labels by using a

USB keyboard. By simply placing digital waveforms next to each other, they form a group.

Arbitrary waveform editor showing the point-by-point editor.

Logic Analyzer (optional)

The logic analyzer (option MDO3MSO) provides 16 digital channels which are tightly integrated into the oscilloscope's user interface. This simplifies operation and makes it possible to solve mixed-signal issues easily.

With color-coded digital waveform display, groups are created by simply placing digital channels together on the screen, allowing digital channels to be moved as a group.

Once a group is formed, you can position all the channels contained in that group collectively. This greatly reduces the normal setup time associated with positioning channels individually

MagniVu

™

high-speed acquisition

The main digital acquisition mode on the MDO3000 Series will capture up to 10 M at 500 MS/s (2 ns resolution). In addition to the main record, the

MDO3000 provides an ultra high-resolution record called MagniVu which acquires 10,000 points at up to 8.25 GS/s (121.2 ps resolution). Both main and MagniVu waveforms are acquired on every trigger and can be switched between in the display at any time, running or stopped. MagniVu provides significantly finer timing resolution than comparable oscilloscopes on the market, instilling confidence when making critical timing measurements on digital waveforms.

The MDO3000 with MDO3MSO option provides 16 integrated digital channels enabling you to view and analyze time-correlated analog and digital signals.

10 www.tektronix.com


Serial Protocol Triggering and Analysis

(optional)

On a serial bus, a single signal often includes address, control, data, and clock information. This can make isolating events of interest difficult.

Automatic trigger, decode, and search on bus events and conditions gives you a robust set of tools for debugging serial buses.

The MagniVu high-resolution record provides 121.2 ps timing resolution, enabling you to take critical timing measurements on your digital waveforms.

P6316 MSO probe

This unique probe design offers two eight-channel pods, simplifying the process of connecting to the device-under-test. When connecting to square pins, the P6316 can connect directly to 8×2 square pin headers spaced on tenth-inch centers. When more attachment flexibility is required, you can use the included flying lead sets and grabbers to clip onto surface mount devices or test points. The P6316 offers outstanding electrical characteristics applying only 8 pF of capacitive loading with 101 kΩ input impedance.

The P6316 MSO probe offers two eight-channel pods to simplify connecting to your device.

Triggering on a specific address and data packet going across an I

2

C bus. The yellow waveform is clock and the blue waveform is the data. A bus waveform provides decoded packet content including Start, Address, Read/Write, Data, and Stop.

Serial triggering

Trigger on packet content such as start of packet, specific addresses, specific data content, unique identifiers, etc. on popular serial interfaces such as I 2 C, SPI, RS-232/422/485/UART, USB2.0, CAN, LIN, FlexRay,

MIL-STD-1553, and I

2

S/LJ/RJ/TDM.

Bus display

Provides a higher-level, combined view of the individual signals (clock, data, chip enable, etc.) that make up your bus, making it easy to identify where packets begin and end and identifying sub-packet components such as address, data, identifier, CRC, etc.

Bus decoding

Tired of having to visually inspect the waveform to count clocks, determine if each bit is a 1 or a 0, combine bits into bytes, and determine the hex value? Let the oscilloscope do it for you! Once you’ve set up a bus, the

MDO3000 Series will decode each packet on the bus, and display the value in hex, binary, decimal (USB, LIN, FlexRay, and MIL-STD-1553 only), signed decimal (I

2

S/LJ/RJ/TDM only), or ASCII (USB, MIL-STD-1553 and

RS-232/422/485/UART only) in the bus waveform.

www.tektronix.com 11

Datasheet

Serial bus technologies supported by the MDO3000

Technology

Embedded

Computer

USB

Automotive

I

2

C

Trigger, Decode,

Search

Yes

SPI

RS232/422/485,

UART

Yes

Yes

USB LS, FS, HS Yes (trigger on LS and FS only; HS decode only on

1 GHz models)

CAN

LIN

FlexRay

MIL-STD-1553

Yes

Yes

Yes

Yes

Order product

MDO3EMBD

MDO3EMBD

MDO3COMP

MDO3USB

MDO3AUTO

MDO3AUTO

MDO3FLEX

MDO3AERO Military and aerospace

Audio I

2

S

LJ, RJ

TDM

Yes

Yes

Yes

MDO3AUDIO

MDO3AUDIO

MDO3AUDIO

Event table

In addition to seeing decoded packet data on the bus waveform itself, you can view all captured packets in a tabular view much like you would see in a software listing. Packets are time stamped and listed consecutively with columns for each component (Address, Data, etc.). You can save the event table data in .CSV format.

Search (serial triggering)

Serial triggering is very useful for isolating the event of interest, but once you’ve captured it and need to analyze the surrounding data, what do you do? In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. You can have the oscilloscope automatically search through the acquired data for user-defined criteria including serial packet content. Each occurrence is highlighted by a search mark. Rapid navigation between marks is as simple as pressing the Previous (←) and Next (→) buttons on the front panel.

Digital Voltmeter (DVM) and Frequency

Counter

The MDO3000 contains an integrated 4-digit digital voltmeter (DVM) and 5digit frequency counter. Any of the analog inputs can be a source for the voltmeter, using the same probes that are already attached for general oscilloscope usage. The easy-to-read display offers you both numeric and graphical representations of the changing measurement values. The display also shows minimum, maximum, and average values of the measurement as well as the range of values measured over the previous five second interval. The DVM and frequency counter is available on any

MDO3000 and is activated when you register your product.

A DC measurement value is shown with a five second variation along with minimum, maximum, and average voltage values. The frequency of the waveform is also shown.

Event table showing decoded identifier, DLC, DATA, and CRC for every CAN packet in a long acquisition.


Designed to fit into your work environment


Compact form factor

With the compact, portable form factor, you can easily move the oscilloscope between labs. And with a depth of just 5.8 inches (147 mm), it saves you valuable space on your test bench. The MDO3000 has all the tools you'll need for everyday debug tasks, all in a single instrument.

The MDO3000 is designed to fit into your work environment. With six instruments in one small, portable package, the MDO3000 offers a unique combination of debug tools without taking up valuable space on your bench.

Large high-resolution display

The MDO3000 Series features a 9 inch (229 mm) wide-screen, highresolution (800 × 480 WVGA) display for seeing intricate signal details.

Connectivity

The MDO3000 contains a number of ports which can be used to connect the instrument to a network, directly to a PC, or other test equipment.

Front and rear USB host ports enable easy transfer of screen shots, instrument settings, and waveform data to a USB mass storage device.

A USB keyboard can also be attached to a USB host port for data entry.

Rear USB device port is useful for controlling the oscilloscope remotely from a PC or for printing directly to a PictBridge

®

-compatible printer.

The standard 10/100 Ethernet port on the rear of the instrument enables easy connection to networks, provides network and e-mail printing, and provides LXI Core 2011 compatibility.

A video out port on the rear of the instrument allows the display to be exported to an external monitor or projector.

The MDO3000 Series compact form factor frees up valuable space on your bench or desktop while making sure you will always have the debug tools you need.


Datasheet

Specifications

All specifications apply to all models unless noted otherwise.

Analog channels

MDO3012 MDO3014 MDO3022 MDO3024 MDO3032 MDO3034 MDO3052 MDO3054 MDO3102 MDO3104

2

Analog channel bandwidth 100 MHz

4

100 MHz

2

200 MHz

4

200 MHz

2

350 MHz

4

350 MHz

2

500 MHz

4

500 MHz

2

1 GHz

4

1 GHz

Rise time

(10 mV/div setting with

50Ω input termination)

Sample rate (1 ch)

4 ns 4 ns 2 ns 2 ns 1.14 ns 1.14 ns 800 ps 800 ps 400 ps 400 ps

Sample rate (2 ch)

Sample rate (4 ch)

Record length (1 ch)

2.5 GS/s

-

2.5 GS/s

10 M

2.5 GS/s

2.5 GS/s

2.5 GS/s

10 M

2.5 GS/s

-

2.5 GS/s

10 M

2.5 GS/s

2.5 GS/s

2.5 GS/s

10 M

2.5 GS/s

-

2.5 GS/s

10 M

2.5 GS/s

2.5 GS/s

2.5 GS/s

10 M

2.5 GS/s

-

2.5 GS/s

10 M

2.5 GS/s

2.5 GS/s

2.5 GS/s

10 M

5 GS/s

-

5 GS/s

10 M

5 GS/s

5 GS/s

2.5 GS/s

10 M

-

10 M

16

10 M

10 M

16

-

10 M

16

10 M

10 M

16

-

10 M

16

10 M

10 M

16

-

10 M

16

10 M

10 M

16

-

10 M

16

10 M

10 M

16



Digital channels with

MDO3MSO option

Arbitrary Function

Generator outputs with

MDO3AFG option

Spectrum analyzer channels

Standard spectrum analyzer frequency range

Optional spectrum analyzer frequency range with MDO3SA option

1

1

9 kHz -

100 MHz

9 kHz -

3 GHz

1

1

9 kHz -

100 MHz

9 kHz -

3 GHz

1

1

9 kHz -

200 MHz

9 kHz -

3 GHz

1

1

9 kHz -

200 MHz

9 kHz -

3 GHz

1

1

9 kHz -

350 MHz

9 kHz -

3 GHz

1

1

9 kHz -

350 MHz

9 kHz -

3 GHz

1

1

9 kHz -

500 MHz

9 kHz -

3 GHz

1

1

9 kHz -

500 MHz

9 kHz -

3 GHz

1

1

9 kHz -

1 GHz

9 kHz -

3 GHz

1

1

9 kHz -

1 GHz

9 kHz -

3 GHz

Vertical system analog channels

Hardware bandwidth limits

≥350 MHz models

20 MHz or 250 MHz

100 MHz and 200 MHz models 20 MHz

AC, DC

Input coupling

Input impedance

Input sensitivity range

1 MΩ

50 Ω, 75 Ω

Vertical resolution

Maximum input voltage

1 MΩ

50 Ω, 75 Ω

1 MΩ ±1%, 50 Ω ±1%, 75 Ω ±1%; 75 Ω not available on 1 GHz models

1 mV/div to 10 V/div

1 mV/div to 1 V/div

8 bits (11 bits with Hi Res)

300 V

RMS

CAT II with peaks ≤ ±425 V

5 V

RMS

with peaks ≤ ±20 V



Vertical system analog channels

DC gain accuracy

±1.5% for 5 mV/div and above, derated at 0.10%/°C above 30 °C

±2.0% for 2 mV/div, derated at 0.10%/°C above 30 °C

±2.5% for 1 mV/div, derated at 0.10%/°C above 30 °C

±3.0% for variable gain, derated 0.10%/°C above 30 °C

Channel-to-channel isolation

Offset range

Any two channels at equal vertical scale ≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth

Volts/div setting

1 mV/div to 50 mV/div

50.5 mV/div to 99.5 mV/div



1 V/div to 5 V/div

Offset range

1 M Ω input

±1 V

±0.5 V

±10 V

±5 V

±100 V

50 Ω, 75 Ω input

±1 V

±0.5 V

±10 V

±5 V

±5 V

Vertical system digital channels

(Requires MDO3MSO option)

Input channels

16 digital (D15 to D0)

Thresholds

Threshold selections

User-defined threshold range

Maximum input voltage

Threshold accuracy

Input dynamic range

Minimum voltage swing

Input resistance

Probe loading

Vertical resolution

Threshold per set of 8 channels

TTL, CMOS, ECL, PECL, User-defined

-15 V to +25 V

-20 V to +30 V

±[100 mV + 3% of threshold setting]

50 V p-p

(threshold setting dependent)

500 mV

101 kΩ

8 pF

1 bit www.tektronix.com 15

Datasheet

Horizontal system analog channels

Time base range

1 GHz models

≤ 500 MHz models

400 ps/div to 1000 s/div

1 ns/div to 1000 s/div

Maximum duration at highest sample rate (all/half channels)

1 GHz models

≤ 500 MHz models

4/2 ms

4/4 ms

Time-base delay time range

-10 divisions to 5000 s

Channel-to-channel deskew range ±125 ns

Time base accuracy

±10 ppm over any ≥1 ms interval

Horizontal system digital channels

(Requires MDO3MSO option)

Maximum sample rate (Main)

500 MS/s (2 ns resolution)

Maximum record length (Main)

10 M

Maximum sample rate (MagniVu)

8.25 GS/s (121.2 ps resolution)

Maximum record length (MagniVu

10k centered on the trigger

Minimum detectable pulse width

(typical)

2 ns

Channel-to-channel skew (typical) 500 ps

Maximum input toggle rate

250 MHz (Maximum frequency sine wave that can accurately be reproduced as a logic square wave. Requires the use of a short ground extender on each channel. This is the maximum frequency at the minimum swing amplitude. Higher toggle rates can be achieved with higher amplitudes.)

Spectrum analyzer input

Capture bandwidth

Span

MDO3012, MDO3014 models: 100 MHz




MDO3102, MDO3104 models: 1 GHz

All models: 3 GHz with option MDO3SA

MDO3012, MDO3014 models: 9 kHz – 100 MHz




MDO3102, MDO3104 models: 9 kHz – 1 GHz

All models: 9 kHz – 3 GHz with option MDO3SA, in a 1-2-5 sequence




Resolution bandwidth

Reference level

Vertical scale

Vertical position

Vertical units

Displayed average noise level

(DANL)

9 kHz - 50 kHz

50 kHz – 5 MHz

5 MHz - 2 GHz

2 GHz – 3 GHz

DANL with TPA-N-PRE preamp attached

9 kHz - 50 kHz

50 kHz – 5 MHz

5 MHz - 2 GHz

2 GHz – 3 GHz

Spurious response

2 nd

harmonic distortion

(>100 MHz)

3 rd

harmonic distortion

(>100MHz)

2 nd order intermodulation distortion (>15 MHz)

3 rd

order intermodulation distortion (>15 MHz)

Residual response

At 2.5 GHz

At 1.25 GHz

Crosstalk to spectrum analyzer from oscilloscope channels

≤800 MHz input frequencies

>800 MHz - 2 GHz input frequencies

Phase noise at 1 GHz CW

10 kHz

100 kHz

1 MHz

20 Hz - 150 MHz in a 1-2-3-5 sequence

-130 dBm to +20 dBm in steps of 5 dBm

1 dB/div to 20 dB/div in a 1-2-5 sequence

-100 divs to +100 divs (displayed in dB) dBm, dBmV, dBµV, dBµW, dBmA, dBµA

< -109 dBm/Hz (< -113 dBm/Hz typical)




Preamp set to "Auto", and Reference Level set to -40 dB





< -55 dBc (< -60 dBc typical)




< -78 dBm (≤ -15 dBm reference level and RF input terminated with 50Ω)

<-67 dBm

<-76 dBm

< -60 dB from ref level (typical)

< -40 dB from ref level (typical)

< -81 dBc/Hz, < -85 dBc/Hz (typical)

< -97 dBc/Hz, < -101 dBc/Hz (typical)

< -118 dBc/Hz, < -122 dBc/Hz (typical) www.tektronix.com 17

Datasheet


Level measurement uncertainty

18 °C - 28 °C

Over operating range

Reference level 10 dBm to -15 dBm. Input level ranging from reference level to 40 dB below reference level. Specifications exclude mismatch error.

< ±1.2 dBm (< ±0.6 dBm typical)

< ±2.0 dBm

Level measurement uncertainty with TPA-N-PRE preamp attached

18 °C - 28 °C

Over operating range

Preamp mode set to “Auto”. Reference level 10 dBm set to -40dBm. Input level ranging from reference level to 30 dB below reference level. Specifications exclude mismatch error.

< ±1.5 dBm (typical) either preamp state

< ±2.3 dBm either preamp state

Frequency measurement accuracy ±(([Reference Frequency Error] x [Marker Frequency]) + (span/750 + 2)) Hz; Reference Frequency Error = 10ppm (10 Hz / MHz)

Maximum operating input level

Average continuous power

+20 dBm (0.1 W)

DC maximum before damage

±40 V DC

Maximum power before damage (CW)

+33 dBm (2 W)

Maximum power before damage (pulse)

+45 dBm (32 W) (<10 µs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm)

Maximum operating input level with TPA-N-PRE preamp attached

Average continuous power

+20 dBm (0.1 W)

DC maximum before damage

±20 V DC

Maximum power before damage (CW)

+30 dBm (1 W)

Maximum power before damage (pulse)

+45 dBm (32 W) (<10 μs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm)

Normal, Average, Max Hold, Min Hold

Frequency domain trace types

Detection methods

+Peak, -Peak, Average, Sample

Automatic markers

Manual markers

Marker readouts

FFT windows

One to eleven peaks identified based on user-adjustable threshold and excursion values

Two manual markers indicating frequency, amplitude, noise density, and phase noise

Absolute or Delta

FFT window

Kaiser

Rectangular

Hamming

Hanning

Blackman-Harris

Flat-Top

Factor

2.23

0.89

1.30

1.44

1.90

3.77



Trigger system

Trigger modes

Trigger coupling

Trigger holdoff range

Trigger sensitivity (typical)

Trigger level ranges

Any input channel

Aux In (External)

Line

Trigger frequency readout

Trigger types

Edge

Sequence (B-trigger)

Pulse Width

Timeout

Runt

Logic

Setup and Hold

Rise/Fall Time

Video

I 2 C (optional)

SPI (optional)

RS-232/422/485/UART

(optional)

Auto, Normal, and Single

DC, AC, HF reject (attenuates >50 kHz), LF reject (attenuates <50 kHz), noise reject (reduces sensitivity)

20 ns to 8 s

Edge type, DC coupled

Trigger source

Any analog channel input

Aux In (External); available on two-channel instruments only

Line

Sensitivity

For 1 mV/div to 4.98 mV/div; 0.75 div from DC to 50 MHz, increasing to 1.3 div at instrument bandwidth

≥ 5mV/div: 0.40 div from DC to 50 MHz

200 mV from DC to 50 MHz, increasing to 500 mV at 200 M

Fixed

±8 divisions from center of screen, ±8 divisions from 0 V when vertical LF reject trigger coupling is selected

±8 V

The line trigger level is fixed at about 50% of the line voltage.

Provides 6-digit frequency readout of triggerable events.

Positive, negative, or either slope on any channel. Coupling includes DC, AC, HF reject, LF reject, and noise reject.

Trigger Delay by Time: 8 ns to 8 s. Or Trigger Delay by Events: 1 to 4,000,000 events. Not available when “Either” edge is selected.

Trigger on width of positive or negative pulses that are >, <, =, ≠, or inside/outside a specified period of time.

Trigger on an event which remains high, low, or either, for a specified time period (4 ns to 8 s).

Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all input channels defined as High, Low, or

Don’t Care.

Trigger on violations of both setup time and hold time between clock and data present on any of the analog and digital input channels.

Setup and hold trigger type

Setup Time Range

Hold Time Range

Setup + Hold Time Range

Description

-0.5 ns to 1.024 ms

1.0 ns to 1.024 ms

0.5 ns to 2.048 ms

Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either and time range is

4.0 ns to 8 s.

Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.

480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30,

1080p/50, 1080p/60

Custom bi-level and tri-level sync video standards.

Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I

2

C buses up to 10 Mb/s.

Trigger on SS active, Start of Frame, MOSI, MISO, or MOSI and MISO on SPI buses up to 50.0 Mb/s.

Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error up to 10 Mb/s.


Datasheet

Trigger system

I

USB: Low speed (optional)

USB: Full speed (optional)

CAN (optional)

LIN (optional)

FlexRay (optional)

MIL-STD-1553 (optional)

2 S/LJ/RJ/TDM (optional)

Parallel (available when option MDO3MSO is installed)

Trigger on Sync Active, Start of Frame, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet,

Handshake Packet, Special Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, Reserved

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special

Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, PRE, Reserved.

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data,

End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s.

Data can be further specified to trigger on ≤, <, =, >, ≥, or ≠ a specific data value. User-adjustable sample point is set to 50% by default.

Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum

Errors up to 100 kb/s (by LIN definition, 20 kb/s).

Trigger on Start of Frame, Type of Frame (Normal, Payload, Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field,

Data, Identifier and Data, End of Frame or Errors such as Header CRC, Trailer CRC, Null Frame, Sync Frame, or Startup Frame

Errors up to 100 Mb/s.

Trigger on Sync, Word Type

1

(Command, Status, Data), Command Word (set RT Address, T/R, Sub-address/Mode, Data Word

Count/Mode Code, and Parity individually), Status Word (set RT Address, Message Error, Instrumentation, Service Request Bit,

Broadcast Command Received, Busy, Subsystem Flag, Dynamic Bus Control Acceptance (DBCA), Terminal Flag, and Parity individually), Data Word (user-specified 16-bit data value), Error (Sync, Parity, Manchester, Non-contiguous data), Idle Time

(minimum time selectable from 2 µs to 100 µs; maximum time selectable from 2 µs to 100 µs; trigger on < minimum, > maximum, inside range, outside range).

RT Address can be further specified to trigger on =, ≠, <, >, ≤, ≥ a particular value, or inside or outside of a range.

Trigger on Word Select, Frame Sync, or Data. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or inside or outside of a range. Maximum data rate for I

2

S/LJ/RJ is 12.5 Mb/s. Maximum data rate for TDM is 25 Mb/s.

Trigger on a parallel bus data value. Parallel bus can be from 1 to 20 bits (from the digital and analog channels) in size. Binary and

Hex radices are supported.

1 Trigger selection of Command Word will trigger on Command and ambiguous Command/Status words. Trigger selection of Status Word will trigger on Status and ambiguous Command/Status words.



Acquisition system

Acquisition modes

Sample

Peak Detect

Averaging

Envelope

Hi Res

Roll

FastAcq

™

Acquire sampled values.

Captures glitches as narrow as 1.5 ns (1 GHz models), 2.0 ns (500 MHz models), 3.0 ns (350 MHz models), 5.0 ns (200 MHz models), 7.0 ns (100 MHz models) at all sweep speeds

From 2 to 512 waveforms included in average.

Min-max envelope reflecting Peak Detect data over multiple acquisitions. Number of waveforms in the envelope selectable between 1 and 2000 and infinity

Real-time boxcar averaging reduces random noise and increases vertical resolution.

Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div.

FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >280,000 wfms/s on

1 GHz models and >235,000 wfms/s on 100 MHz – 500 MHz models.

Waveform measurements

Cursors

Automatic measurements

(time domain)

Automatic Measurements

(frequency domain)

Measurement statistics

Reference levels

Gating

Waveform histogram

Sources

Types

Waveform histogram measurements

Waveform and Screen

30, of which up to four can be displayed on-screen at any one time. Measurements include: Period, Frequency, Delay, Rise Time,

Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive

Overshoot, Negative Overshoot, Total Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle

RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area and Cycle Area.

3, of which one can be displayed on-screen at any one time. Measurements include Channel Power, Adjacent Channel Power

Ratio (ACPR), and Occupied Bandwidth (OBW)

Mean, Min, Max, Standard Deviation.

User-definable reference levels for automatic measurements can be specified in either percent or units.

Isolate the specific occurrence within an acquisition to take measurements on, using either the screen or waveform cursors.

A waveform histogram provides an array of data values representing the total number of hits inside of a user-defined region of the display. A waveform histogram is both a visual graph of the hit distribution as well as a numeric array of values that can be measured.

Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math

Vertical, Horizontal

12, of which up to four can be displayed on-screen at any one time. Waveform Count, Hits in Box, Peak Hits, Median, Max, Min,

Peak-to-Peak, Mean, Standard Deviation, Sigma 1, Sigma 2, Sigma 3

Waveform math

Arithmetic

Math functions

FFT

Add, subtract, multiply, and divide waveforms.

Integrate, differentiate, FFT

Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or

Blackman-Harris.


Datasheet

Waveform math

Spectrum math

Advanced Math

Add or subtract frequency-domain traces.

Define extensive algebraic expressions including waveforms, reference waveforms, math functions (FFT, Intg, Diff, Log, Exp, Sqrt,

Abs, Sine, Cosine, Tangent, Rad, Deg), scalars, up to two user-adjustable variables and results of parametric measurements

(Period, Freq, Delay, Rise, Fall, PosWidth, NegWidth, BurstWidth, Phase, PosDutyCycle, NegDutyCycle, PosOverShoot,

NegOverShoot, TotalOverShoot, PeakPeak, Amplitude, RMS, CycleRMS, High, Low, Max, Min, Mean, CycleMean, Area,

CycleArea, and trend plots). for example, (Intg(Ch1 - Mean(Ch1)) × 1.414 × VAR1)

Act on Event

Events

Actions

Repeat

None, when a trigger occurs, or when a defined number of acquisitions complete (1 to 1,000,000)

Stop acquisition, save waveform to file, save screen image, print, AUX OUT Pulse, remote interface SRQ, e-mail notification, and visual notification

Repeat the act on event process (1 to 1,000,000 and infinity)

Video Picture mode

Sources

Video standards

Contrast and brightness

Field selection

Picture location on screen

Channel 1, Channel 2, Channel 3, Channel 4

NTSC, PAL

Manual and automatic

Odd, Even, Interlaced

Selectable X and Y location, width and height adjustment, start line and pixel and line-to-line offset control.

Power measurements (optional)

Power quality measurements

V

RMS

, V

Crest Factor

, Frequency, I

RMS

, I

Crest Factor

, True Power, Apparent Power, Reactive Power, Power Factor, Phase Angle.

Switching loss measurements

Power loss

Energy loss

Harmonics

T on

, T off

, Conduction, Total.

T on

, T off

, Conduction, Total.

THD-F, THD-R, RMS measurements. Graphical and table displays of harmonics. Test to IEC61000-3-2 Class A and MIL-

STD-1399, Section 300A.

Ripple measurements

Modulation analysis

Safe operating area dV/dt and dI/dt measurements

V

Ripple

and I

Ripple

.

Graphical display of +Pulse Width, -Pulse Width, Period, Frequency, +Duty Cycle, and -Duty Cycle modulation types.

Graphical display and mask testing of switching device safe operating area measurements.

Cursor measurements of slew rate



Limit/Mask testing (optional)

Test source

Limit test: Any Ch1 - Ch4 or any R1 - R4

Mask test: Any Ch1 - Ch4

Mask creation

Mask scaling

Test criteria run until

Violation threshold

Actions on test failure

Actions on test complete

Results display

Limit test vertical tolerance from 0 to 1 division in 1 m division increments; Limit test horizontal tolerance from 0 to 500 m division in

1 m division increments.

Load custom mask from text file with up to 8 segments.

Lock to Source ON (mask automatically re-scales with source-channel settings changes)

Lock to Source OFF (mask does not re-scale with source-channel settings changes)

Minimum number of waveforms (from 1 to 1,000,000 and Infinity)

Minimum elapsed time (from 1 second to 48 hours and Infinity)

From 1 to 1,000,000 and Infinity

Stop acquisition, save screen image to file, save waveform to file, print screen image, AUX OUT pulse, set remote interface SRQ

AUX OUT pulse, set remote interface SRQ

Test status, total waveforms, number of violations, total tests, failed tests, elapsed time, total hits for each mask segment

Arbitrary Function Generator

(Requires MDO3AFG option)

Waveforms

Sine, Square, Pulse, Ramp/Triangle, DC, Noise, Sin(x)/x (Sinc), Gaussian, Lorentz, Exponential Rise, Exponential Decay,

Haversine, Cardiac, and Arbitrary.

Sine

Frequency range

Amplitude range

Amplitude flatness

Total harmonic distortion

(typical)

Spurious free dynamic range

(SFDR)

0.1 Hz to 50 MHz

20 mV p-p

to 5 V p-p

into Hi-Z; 10 mV p-p

to 2.5 V p-p

into 50 Ω

±0.5 dB typical at 1 kHz (±1.5 dB for <20 mV p-p

amplitudes)

1% into 50Ω

2% for amplitude < 50 mV and frequencies > 10 MHz

3% for amplitude < 20 mV and frequencies > 10 MHz

-40 dBc (V p-p

≥ 0.1 V); -30dBc (V p-p

≤ 0.1 V), 50 Ω load

Square / Pulse

Frequency range

Amplitude range

Duty cycle

Duty cycle resolution

Pulse width minimum

Rise/fall time

Pulse width resolution

Overshoot

Asymmetry

Jitter (TIE RMS)

0.1 Hz to 25 MHz

20 mV p-p

to 5 V p-p


to 2.5 V p-p

into 50 Ω

10% to 90% or 10 ns minimum pulse, whichever is larger cycle

0.1%

10 ns typical

5 ns typical (10% - 90%)

100 ps

< 2% typical for signal steps greater than 100 mV

±1% ±5 ns, at 50% duty cycle

< 500 ps typical www.tektronix.com 23

Datasheet


Ramp / Triangle

Frequency range

Amplitude range

Variable symmetry

Symmetry resolution

0.1 Hz to 500 kHz

20 mV p-p

to 5 V p-p


to 2.5 V p-p

into 50 Ω

0% to 100%

0.1%

DC

Level range

±2.5 V into Hi-Z; ±1.25 V into 50 Ω

Noise

Amplitude range

Amplitude resolution

Sin(x)/x (Sinc)

Frequency range

Amplitude range

Gaussian

Frequency range

Amplitude range

Lorentz

Frequency range

Amplitude range

Exponential Rise / Decay

Frequency range

Amplitude range

Haversine

Frequency range

Amplitude range

Cardiac

Frequency range

Amplitude range

Arbitrary

Memory depth

Amplitude range

Repetition rate

Sample rate

Frequency accuracy

Sine wave and ramp

20 mV p-p

to 5 V p-p

in to Hi-Z; 10 mV p-p

to 2.5 V p-p

into 50 Ω

0% to 100% in 1% increments

0.1 Hz to 2 MHz

20 mV p-p

to 3.0 V p-p


to 1.5 V p-p

into 50 Ω

0.1 Hz to 5 MHz

20 mV p-p

to 2.5 V p-p


to 1.25 V p-p

into 50 Ω

0.1 Hz to 5 MHz

20 mV p-p

to 2.4 V p-p


to 1.2 V p-p

into 50 Ω

0.1 Hz to 5 MHz

20 mV p-p

to 2.5 V p-p


to 1.25 V p-p

into 50 Ω

0.1 Hz to 5 MHz

20 mV p-p

to 2.5 V p-p


to 1.25 V p-p

into 50 Ω

0.1 Hz to 500 kHz

20 mV p-p

to 5 V p-p


to 2.5 V p-p

into 50 Ω

1 to 128 k

20 mV p-p

to 5 V p-p


to 2.5 V p-p

into 50 Ω

0.1 Hz to 25 MHz

250 MS/s

Square wave and pulse

Resolution

130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

0.1 Hz or 4 digits; whichever is larger




Amplitude accuracy

±[ (1.5% of peak-to-peak amplitude setting) + (1.5% of DC offset setting) + 1 mV ] (frequency = 1 kHz)

DC offset

DC offset range

DC offset resolution

Offset accuracy

ArbExpress

®

±[2.5 V – (signal amplitude) / 2 ] into Hi-Z; ±[1.25 – (signal amplitude) / 2 ] into 50 Ω

1 mV into Hi-Z; 500 uV into 50 Ω

±[(1.5% of absolute offset voltage setting) + 1 mV]; derated 3 mV for every 10 °C away from 25 °C

The MDO3000 is compatible with ArbExpress

®

PC-based signal generator waveform creation and editing software. Capture waveforms on the MDO3000 oscilloscope and transfer them to ArbExpress for editing. Create complex waveforms in ArbExpress and transfer them to the arbitrary function generator in the MDO3000 for output. To download ArbExpress software, go to www.tektronix.com/downloads .

Digital voltmeter (DVM) and frequency counter

Source

Channel 1, Channel 2, Channel 3, Channel 4

AC RMS, DC, AC+DC RMS (reads out in volts or amps); Frequency

Measurement types

Resolution

ACV, DCV: 4 digits

Frequency: 5 digits

Frequency accuracy

Measuring rate

Vertical settings autorange

Graphical measurement

10 ppm

100 times/second; measurements updated on the display 4 times/second

Automatic adjustment of vertical settings to maximize measurement dynamic range; available for any non-trigger source

Graphical indication of minimum, maximum, current value, and five second rolling range

Software

OpenChoice

®

Desktop

IVI driver e*Scope

®

Web-based interface

LXI Core 2011 Web interface

Enables fast and easy communication between a Windows PC and your oscilloscope using USB or LAN. Transfer and save settings, waveforms, measurements, and screen images. Word and Excel toolbars automate the transfer of acquisition data and screen images from the oscilloscope into Word and Excel for quick reporting or further analysis.

Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI,

MicrosoftNET, and MATLAB.

Enables control of the oscilloscope over a network connection through a standard web browser. Simply enter the IP address or network name of the oscilloscope and a web page will be served to the browser. Transfer and save settings, waveforms, measurements, and screen images or make live control changes to settings on the oscilloscope directly from the web browser.

Connect to the oscilloscope through a standard Web browser by simply entering the oscilloscope IP address or network name in the address bar of the browser. The Web interface enables viewing of instrument status and configuration, status and modification of network settings, and instrument control through e*Scope Web-based remote control. All Web interaction conforms to LXI Core

2011 specification, version 1.4.


Datasheet

Display system

Display type

Display resolution

Interpolation

9 in. (229 mm) color display

800 horizontal × 480 vertical pixels (WVGA)

Sin(x)/x

Waveform styles

FastAcq. palettes

Graticules

Format

Vectors, Dots, Variable Persistence, Infinite Persistence

Temperature, Spectral, Normal, Inverted

Full, Grid, Solid, Cross Hair, Frame, IRE and mV

YT, XY, and simultaneous XY/YT

Maximum waveform capture rate

>280,000 wfms/s in FastAcq acquisition mode for 1 GHz models

>235,000 wfms/s in FastAcq acquisition mode for 100 MHz – 500 MHz models

>50,000 wfms/s in DPO acquisition mode on all models

Input/output ports

USB 2.0 high-speed host port

USB 2.0 device port

Supports USB mass storage devices, printers and keyboard. One port on front and one port on rear of instrument.

Rear-panel connector allows for communication/control of oscilloscope through USBTMC or GPIB (with a TEK-USB-488), and direct printing to PictBridge-compatible printers.

Printing

Print to network printer, PictBridge printer, or to a printer that supports e-mail printing. Note: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)

LAN port

Video out port

RJ-45 connector, supports 10/100 Mb/s

DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector. XGA resolution.

Auxilliary input

Front-panel BNC connector

Maximum input

(Available on two-channel models only)

Input impedance, 1 MΩ

300 V

RMS

CAT II with peaks ≤ ±425 V

Probe compenstor output voltage and frequency

Amplitude

Frequency

Front-panel pins

0 to 2.5 V

1 kHz

Auxiliary out

Rear-panel BNC connector

V

OUT

(Hi): ≥2.25 V open circuit, ≥0.9 V 50 Ω to ground

V

OUT

(Lo): ≤0.7 V into a load of ≤4 mA; ≤0.25 V 50 Ω to ground

Output can be configured to provide a pulse out signal when the oscilloscope triggers, a trigger signal from the internal arbitrary function generator, or an event out for limit/mask testing.

Rear-panel security slot connects to standard Kensington-style lock.

Kensington-style lock

VESA mount

Standard (MIS-D 75) 75 mm VESA mounting points on rear of instrument.



LAN eXtensions for Instrumentation (LXI)

Class

LXI Core 2011

Version

V1.4

Power source

Power source voltage

Power source frequency

Power consumption

100 to 240 V ±10%

50 to 60 Hz at 100 to 240 V

400 Hz ±10% at 115 V

120 W maximum

Physical characteristics

Dimensions

Height

Width

Depth

Weight

Net

Shipping

Rackmount configuration

Cooling clearance

203.2 mm (8 in.)

416.6 mm (16.4 in.)

147.4 mm (5.8 in.)

4.2 kg (9.2 lb.)

8.6 kg (19 lb.)

5U

2 in. (51 mm) required on left side and rear of instrument

EMC, environment, and safety

Temperature

Operating

Nonoperating

-10 ºC to +55 ºC (+14 ºF to 131 ºF)

-40 ºC to +71 ºC (-40 ºF to 160 ºF)

Humidity

Operating

Nonoperating

Up to +40 ºC, 5% to 90% relative humidity

+40 ºC to +55 ºC, 5% to 60% relative humidity

Up to +40 ºC, 5% to 90% relative humidity

Above +40 ºC up to +55 ºC, 5% to 60% relative humidity

Above +55 ºC up to +71 ºC, 5% to 40% relative humidity, non-condensing

Altitude

Operating

Nonoperating

3,000 meters (9,843 feet)

12,000 meters (39,370 feet)

Regulatory

Electromagnetic compatibility EC Council Directive 2004/108/EC

Safety

UL61010-1:2004, CAN/CSA-C22.2 No. 61010.1: 2004, Low Voltage Directive 2006/95/EC and EN61010-1:2001, IEC

61010-1:2001, ANSI 61010-1-2004, ISA 82.02.01 www.tektronix.com 27

Datasheet

Ordering information

Step 1: Choose the MDO3000 base model

MDO3000 family

MDO3012

MDO3014

MDO3022

MDO3024

MDO3032

MDO3034

MDO3052

MDO3054

MDO3102

MDO3104

Mixed Domain Oscilloscope with (2) 100 MHz analog channels, and (1) 100 MHz spectrum analyzer input








Mixed Domain Oscilloscope with (2) 1 GHz analog channels, and (1) 1 GHz spectrum analyzer input

Mixed Domain Oscilloscope with (4) 1 GHz analog channels, and (1) 1 GHz spectrum analyzer input

Standard accessories

Probes

100 MHz, 200 MHz models

350 MHz, 500 MHz models

1 GHz models

TPP0250, 250 MHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

TPP0500B, 500 MHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

TPP1000, 1 GHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

Any model with MDO3MSO option One P6316 16-channel logic probe and accessories

Accessories

103-0473-00

-

-

-

063-4526-xx

071-3249-00

016-2008-xx

N-to-BNC adapter

Documentation CD

Installation and Safety Instructions, printed manual (translated in English, Japanese, and Simplified Chinese)

Accessory bag

Power cord

OpenChoice

®

Desktop Software (available on the Documentation CD and for download from www.tektronix.com/downloads .)

Calibration certificate documenting traceability to National Metrology Institute(s) and ISO9001 quality system registration

for all your test instrument needs

UK strategic partner for Tektronix

Thurlby Thandar instrument distribution • Glebe Road • Huntingdon • Cambs. • PE29 7DR

Tel: 01480 412451

•

info@ ttid.co.uk

•

www.

ttid.co.uk/tek



Warranty

Three-year warranty covering all parts and labor, excluding probes.

Step 2: Configure your MDO3000 by adding instrument options

Instrument options

All MDO3000 Series instruments can be preconfigured from the factory with the following options:

MDO3AFG

MDO3MSO

MDO3SA

MDO3SEC

Arbitrary function generator with 13 predefined waveforms and arbitrary waveform generation

16 digital channels; includes P6316 digital probe and accessories

Increase spectrum analyzer input frequency range to 9 kHz – 3 GHz and capture bandwidth to 3 GHz.

Enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware update functionality.

Power cord and plug options

Opt. A0

Opt. A1

Opt. A2

Opt. A3

Opt. A5

Opt. A6

Opt. A10

Opt. A11

Opt. A12

Opt. A99

North America power plug (115 V, 60 Hz)

Universal Euro power plug (220 V, 50 Hz)

United Kingdom power plug (240 V, 50 Hz)

Australia power plug (240 V, 50 Hz)

Switzerland power plug (220 V, 50 Hz)

Japan power plug (100 V, 110/120 V, 60 Hz)

China power plug (50 Hz)

India power plug (50 Hz)

Brazil power plug (60 Hz)

No power cord

Language options

All products are shipped with an Installation and Safety manual that is in English, Japanese, and Simplified Chinese. Full user manuals translated in each language listed below are included with each product in pdf format on the Documentation CD.

Opt. L0

Opt. L1

Opt. L2

Opt. L3

Opt. L4

Opt. L5

Opt. L6

Opt. L7

Opt. L8

Opt. L9

English front panel label

French front panel overlay

Italian front panel overlay

German front panel overlay

Spanish front panel overlay

Japanese front panel overlay

Portuguese front panel overlay

Simplified Chinese front panel overlay

Traditional Chinese front panel overlay

Korean front panel overlay www.tektronix.com 29

Datasheet

Opt. L10

Opt. L99

Russian front panel overlay

No manual, English front panel label

Service options

Opt. C3

Opt. C5

Opt. D1

Opt. D3

Opt. D5

Opt. G3

Calibration Service 3 Years

Calibration Service 5 Years

Calibration Data Report

Calibration Data Report 3 Years (with Opt. C3)

Calibration Data Report 5 Years (with Opt. C5)

Complete Care 3 Years (includes loaner, scheduled calibration, and more)

Opt. G5

Complete Care 5 Years (includes loaner, scheduled calibration, and more)

Opt. R5

Repair Service 5 Years (including warranty)

Probes and accessories are not covered by the oscilloscope warranty and service offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms.

Step 3: Select application models and accessories

Application modules

MDO3AERO

MDO3AUDIO

MDO3AUTO

MDO3COMP

Application modules are purchased as stand-alone products and can be purchased at the time of initial MDO3000 purchase or at any future time.

Application modules have licenses which can be transferred between an application module and an oscilloscope. The license may be contained in the module; allowing the module to be moved from one instrument to another. Or, the license can be contained in the oscilloscope; allowing the module to be removed and stored for safekeeping. The license can be transferred back to the module for use in another MDO3000 oscilloscope. Transferring the license to an oscilloscope and removing the module permits the use of more than two applications simultaneously.

Aerospace Serial Triggering and Analysis Module. Enables triggering on packet-level information on MIL-STD-1553 buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time- stamp information.

Signal Inputs - Any Ch1 - Ch4, Math, Ref1 - Ref4

Recommended Probing - Differential or single ended (only one single-ended signal required)

Audio Serial Triggering and Analysis Module. Enables triggering on packet-level information on I

2

S, LJ, RJ, and TDM audio buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

Automotive Serial Triggering and Analysis Module. Enables triggering on packet-level information on CAN and LIN buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time- stamp information.

Signal Inputs – CAN or LIN: Any Ch1 - Ch4, any D0 - D15

Recommended Probing - CAN: Single ended or differential; LIN: Single ended

Computer Serial Triggering and Analysis Module. Enables triggering on packet-level information on RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - RS-232/UART: Single ended; RS-422/485: Differential



MDO3EMBD

MDO3FLEX

MDO3USB

MDO3PWR

MDO3LMT

Embedded Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2C and SPI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with timestamp information.

Signal Inputs - I

2

C or SPI: Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

FlexRay Serial Triggering and Analysis Module. Enables triggering on packet-level information on FlexRay buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4 (and any D0 - D15 when MDO3MSO option is installed; single-ended probing only)

Recommended Probing - Single ended or differential

USB Serial Triggering and Analysis Module. Enables triggering on packet-level content for low-speed, and full-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information for low-speed, full-speed, and high-speed USB serial buses.

Signal Inputs - Low-speed and Full-speed: Any Ch1 - Ch4, any D0 - D15; Low-speed, Full-speed, and High-speed: Any Ch1 - Ch4,

Math, Ref1 - Ref4

Note: High-speed decode support only available on 1 GHz models.

Recommended Probing - Low-speed and Full-speed: Single ended or differential; High-speed: Differential

Power Analysis Application Module. Enables quick and accurate analysis of power quality, switching loss, harmonics, safe operating area (SOA), modulation, ripple, and slew rate (dI/dt, dV/dt).

Limit and Mask Testing Application Module. Enables testing against limit templates generated from "golden" waveforms and mask testing using custom masks.

Recommended accessories

Probes

Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit www.tektronix.com/probes .

TPP0250

TPP0500B

TPP0502

TPP0850

250 MHz, 10X TekVPI

®

passive voltage probe with 3.9 pF input capacitance

500 MHz, 10X TekVPI

®


500 MHz, 2X TekVPI

®


2.5 kV, 800 MHz, 50X TekVPI

®

passive high-voltage probe

TPP1000

TAP1500

TAP2500

1 GHz, 10X TekVPI

®


1.5 GHz TekVPI

®

active single-ended voltage probe

2.5 GHz TekVPI

®


TAP3500

TCP0020

TCP0030A

TCP0150

TDP0500

TDP1000

TDP1500

3.5 GHz TekVPI

®


50 MHz TekVPI

®

20 Ampere AC/DC current probe

120 MHz TekVPI

®


20 MHz TekVPI

®


500 MHz TekVPI

®

differential voltage probe with ±42 V differential input voltage

1 GHz TekVPI

®


1.5 GHz TekVPI

®

differential voltage probe with ±8.5 V differential input voltage

TDP3500

THDP0200

3.5 GHz TekVPI

®


±1.5 kV, 200 MHz TekVPI

®

high-voltage differential probe www.tektronix.com 31

Datasheet

THDP0100

TMDP0200

Accessories

TPA-N-PRE

TPA-N-VPI

119-4146-00

119-6609-00

077-0981-xx

TPA-BNC

TEK-DPG

067-1686-xx

SignalVu-PC-SVE

TEK-USB-488

ACD3000

HCTEK54

RMD3000

200-5052-00

±6 kV, 100 MHz TekVPI

®

high-voltage differential probe

±750 V, 200 MHz TekVPI

®

high-voltage differential probe

Preamplifier, 12 dB nominal Gain, 9 kHz - 6 GHz

N-to-TekVPI adapter

Near field probe set, 100 kHz - 1 GHz

Flexible monopole antenna

Service manual (English only)

TekVPI

®

to TekProbe

™

BNC adapter

TekVPI Deskew pulse generator signal source

Power measurement deskew and calibration fixture

Vector Signal Analysis Software

GPIB-to-USB adapter

Soft transit case (includes front protective cover)

Hard transit case (requires ACD3000)

Rackmount kit

Front protective cover

Other RF probes

Contact Beehive Electronics to order: http://beehive-electronics.com/probes.html

101A

150A

110A

0309-0001

0309-0006

EMC probe set

EMC probe amplifier

Probe cable

SMA probe adapter

BNC probe adapter



Step 4: Add instrument upgrades in the future

Instrument upgrades

The MDO3000 Series products offer a number of ways to add functionality after the initial purchase. Listed below are the various product upgrades available and the method of upgrade used for each product.

Post-purchase instrument options The following products are sold as stand-alone products and can be purchased at any time to add functionality to any MDO3000 product.

MDO3AFG

Add arbitrary function generator to any MDO3000 Series product.

MDO3MSO

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is used to enable the feature and then is not required for future use.

Add 16 digital channels; includes P6316 digital probe and accessories .

MDO3SA


Increase spectrum analyzer input frequency range to 9 kHz – 3 GHz and capture bandwidth to 3 GHz.

MDO3SEC


Add enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware update functionality.

One-time, permanent upgrade to any model enabled through software option key. Software option key products require that the instrument model and serial number be provided at the time of purchase. The software option key is specific to the model and serial number combination.


Datasheet

Bandwidth upgrade options

Instrument bandwidth can be upgraded on any MDO3000 Series product after initial purchase. Each upgrade product will increase the analog bandwidth and the spectrum analyzer frequency range to the new bandwidth level. Bandwidth upgrades are purchased based on the combination of the current bandwidth and the desired bandwidth. Software option key products require that the instrument model and serial number be provided at the time of purchase. The software option key is specific to the model and serial number combination. Bandwidth upgrades up to 500 MHz can be performed in the field. Bandwidth upgrades to 1 GHz require installation at a Tektronix service center. The table below shows the various bandwidth upgrade products to purchase based on current and desired bandwidth levels.

Model to be upgraded

MDO3012

MDO3014

MDO3022

MDO3024

MDO3032

MDO3034

350 MHz

350 MHz

500 MHz

200 MHz

200 MHz

200 MHz

350 MHz

350 MHz

500 MHz

350 MHz

350 MHz

500 MHz

350 MHz

350 MHz

500 MHz

100 MHz

100 MHz

100 MHz

200 MHz

200 MHz

200 MHz

350 MHz

350 MHz

500 MHz

200 MHz

200 MHz

200 MHz

Bandwidth before upgrade Bandwidth after upgrade

100 MHz 200 MHz

100 MHz 350 MHz

100 MHz

100 MHz

200 MHz

500 MHz

1 GHz

350 MHz

200 MHz

200 MHz

350 MHz

350 MHz

500 MHz

100 MHz

500 MHz

1 GHz

500 MHz

1 GHz

1 GHz

200 MHz

350 MHz

500 MHz

1 GHz

350 MHz

500 MHz

1 GHz

500 MHz

1 GHz

1 GHz

350 MHz

500 MHz

1 GHz

500 MHz

1 GHz

1 GHz

350 MHz

500 MHz

1 GHz

500 MHz

1 GHz

1 GHz

500 MHz

1 GHz

1 GHz

500 MHz

1 GHz

1 GHz

Order protduct

MDO3BW1T22

MDO3BW1T32

MDO3BW1T52

MDO3BW1T102

MDO3BW2T32

MDO3BW2T52

MDO3BW2T102

MDO3BW3T52

MDO3BW3T102

MDO3BW5T102

MDO3BW1T24

MDO3BW1T34

MDO3BW1T54

MDO3BW1T104

MDO3BW2T34

MDO3BW2T54

MDO3BW2T104

MDO3BW3T54

MDO3BW3T104

MDO3BW5T104

MDO3BW2T32

MDO3BW2T52

MDO3BW2T102

MDO3BW3T52

MDO3BW3T102

MDO3BW5T102

MDO3BW2T34

MDO3BW2T54

MDO3BW2T104

MDO3BW3T54

MDO3BW3T104

MDO3BW5T104

MDO3BW3T52

MDO3BW3T102

MDO3BW5T102

MDO3BW3T54

MDO3BW3T104

MDO3BW5T104



Model to be upgraded

MDO3052

MDO3054

Bandwidth before upgrade Bandwidth after upgrade

500 MHz 1 GHz

500 MHz 1 GHz

Order protduct

MDO3BW5T102

MDO3BW5T104

Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.

Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.

for all your test instrument needs

UK strategic partner for Tektronix

Thurlby Thandar instrument distribution • Glebe Road • Huntingdon • Cambs. • PE29 7DR

Tel: 01480 412451

•

info@

ttid.co.uk

•

www.

ttid.co.uk/tek


No results