Avid Configuration Guidelines
HP Z400 Single Quad-Core CPU Workstation
Gen1 Z400 – 4 DIMM / No Embedded Firewire
Media Composer 6.0, NewsCutter 10 and later
(To configure a Z400 for prior versions of Avid software see the earlier version Z400 guide posted on the Avid KB)
1.) HP Z400 AVID Qualified System Specification:
Z400 / AVID Qualified Operating System choices:
Microsoft® Windows 7 Professional 64-bit Edition with Service Pack 1
Z400 Hardware Configuration
Qualified CPU Choices
1.) Single Intel® Quad-Core Xeon® W3550 Processor @ 3.06GHz 8MB cache / 1066MHz memory
2.) Single Intel® Quad-Core Xeon® W3540 Processor @ 2.93GHz 8MB cache / 1066MHz memory
^^
^^
This processor selection has gone End-of-Life and is no longer available in new systems being purchased from H.P.
Video Card Choice
NVIDIA Quadro FX 3800 1GB PCI-E video board
System Hard Drive
320GB SATA-II 3Gb/s 7200RPM Hard Disk Drive (Minimum Recommendation)
Memory Configuration
Memory: 6GB (3 x 2GB) DDR3 1333 ECC memory –
(Requires three 2GB DIMMs, DIMM sizes cannot be mixed sizes )
2GB memory modules must be installed in the following memory slots:
Memory configuration constraints
No other memory configurations are recommended in Z400 AVID environments. Only the 6GB (3 x 2GB) configuration is supported. Memory configurations which mix and match memory module sizes and locations will result in a poor performing, non-optimal operating environment.
1394a Firewire HBA requirement (For Firewire device support) (H.P. Option NM980AV)
NM980AV HP 3-port PCI 1394a Firewire IEEE HBA option (Installs in slot 5, has two external rear 1394a ports and also connects to front panel 1394a port) (Standard part of AVID Gen1 Z400 specific system SKU).
Page 1 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
2.) Qualified Operating Systems for Avid Client Editing Applications, Hardware and Shared-Storage connectivity for the HP Z400 with Media Composer 6.0 and NewsCutter 10 or later:
-
Supported: Only Microsoft® Windows 7 Professional 64-bit Edition with SP1 (SP1 required)
-
Not Supported - Microsoft® Windows XP 32-bit, 64-bit (any version)
-
Not Supported - Microsoft® Windows Vista 32-bit, 64-bit (any version)
-
Not Supported - Microsoft® Windows 7 – any 32-bit version, or any version of Home, Ultimate or
Enterprise editions.
Note regarding Service packs:
As of this writing Service Pack 1 is the current Service Pack release for Win7. SP1 is required for Media
Composer 6.0 and NewsCutter 10. As future Service Packs are released Avid will evaluate and announce formal support when testing is completed.
3.) Qualified Hardware and shared storage supported:
AVID qualified Hardware / Shared Storage
Qualified / Supported
Mojo DX
Nitris DX
3 rd
Party Qualified Hardware
Unity ISIS System Infrastructure
Unity ISIS 1 Gbit Ethernet Client
Unity ISIS Hi-res (10 Gbit) client
Unity MediaNet Infrastructure
Unity MediaNet Fibre
Unity MediaNet AECIFs
1394 Adrenaline DNA
1394 Mojo-SDI DNA
1394 Mojo-Analog DNA
Yes
Yes
See release notes and Avid website for rd information regarding supported 3 party hardware (vendor qualified)
ISIS 1.4 Infrastructure
ISIS 2.03 Client
Requires minimum ISIS 2.2
(ISIS 7000 only)
MediaNet 4.2.4 Infrastructure
MediaNet 5.1.2 Client
MediaNet 5.1.2 Client
N/A Not Supported
N/A Not Supported
N/A Not Supported
Page 2 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
AVID qualified HBA
Avid HIB, DX Interface HBA
**
Qualified 3 rd
party hardware interface
Active: 7030-30048-01
Active: 7030-20084-01
Passive: 7030-30021-01
Not stocked by AVID
AVID qualified HBA info
AVID Part Number Slot
#1
#1
Atto FC-41ES
Intel PRO 1000 PT - ISIS
Intel PRO 1000 PF - ISIS
***
Myricom
10G-PCIE-8B-S
Requires minimum ISIS 2.2
(ISIS 7000 only)
LSI 9200-8e SAS controller
Atto H680
Atto R380
Atto UL5D
***
H.P. NM980AV 3-port PCI
1394a Firewire IEEE HBA
7030-20004-01
7030-20139-01
Not stocked by AVID
7030-30041-01
7030-30036-01
7030-30028-01
7030-20166-01
7030-20002-01
7030-20154-01
#4
#4
#4
#3
#3
#3
#4
#4
#5
Function
Avid DX Hardware Interface HBA
See release notes and Avid website for information regarding supported 3 rd
party hardware. (Vendor qualified)
Shared Storage: MediaNet LAN-Share Fibre
Shared Storage: Unity ISIS Copper Gb-Ethernet
Shared Storage: Unity ISIS Optical Gb-Ethernet
Shared Storage: Unity ISIS 10Gb-Ethernet
Requires minimum ISIS 2.2
(ISIS 7000 only)
SAS Local Storage:
Xtore StudioRAID 16Re (16-bay) chassis
Xtore StudioRAID 5Te (5-bay) chassis
SAS Local Storage – Avid VideoRAID SR (16-bay)
SAS Local Storage –Avid VideoRAID ST (5-bay) and Xtore StudioRAID 5Ti (5-bay) chassis
Local Storage – VideoRAID RTR &
Legacy Avid u320 SCSI storage
(The UL5D BIOS should be disabled)
1394 Camera / Deck support
Page 3 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Specific Important qualified HBA Support Notes
**
Avid DX Interface HBA Support Note: (See reference pictures on page 6 of this guide ).
All 3 versions of the DX interface HBA are supported with Media Composer 6.x and NewsCutter 10.x
1) Active DX interface HBA 7030-30048-01
2) Active DX interface HBA 7030-20084-01
3) Passive DX interface HBA 7030-30021-01
***
Atto FC-41ES HBA Support Note:.
1) The Z400 requires a Rev D or later version FC-41ES. The board revision is clearly marked on a label on the back of the FC-41ES. Earlier revisions (A, B and C) of the FC-41ES may demonstrate compatibility issues when used with the Z400 including not being recognized by the Z400 CPU.
***
Myricom 10G-PCIE-8B-S 10Gb Interface HBA Support Notes.
1) Initial shared storage HBA’s used in the Z400 resided in slot #3. However, the Myricom 10G-PCIE-8B-S must reside in slot #4 as this HBA requires the performance of the additional PCI-E lanes offered for slot#4. It will not function properly if used in slot #3. Using the Myricom 10G-PCIE-8B-S for ISIS 2.2.x connectivity will not allow for support of simultaneous connection to local storage in Z400 configurations as the local storage controllers must also reside in slot #4.
Page 4 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
4.) Slot Configuration:
Slot #
1
2
3
4
5
6
Electrical x4 PCI-E Gen 2
(25Watts) x16 PCI-E Gen 2
(75Watts) x4 PCI-E Gen 1
(25Watts) x16 PCI-E Gen 2
(75Watts)
PCI 32bit /33MHz
PCI 32bit /33MHz
Mechanical x8 x16 x8 x16
PCI 32/33
PCI 32/33
Slot Configuration Information
Avid HIB, DX Interface HBA
Active: 7030-30048-01 & 7030-20084-01
Passive: 7030-30021-01
OR
Vendor
Qualified 3 rd
Party Hardware PCI-e Interface
See release notes and Avid website for information regarding rd supported 3 party hardware (vendor qualified)
Graphics Card:
Quadro FX 3800
Shared Storage Controllers:
Atto FC-41ES - MediaNet LAN Share
Intel PRO 1000 PT - ISIS 5000 / 7000
Intel PRO 1000 PF - ISIS 5000 / 7000
Local Storage Controllers:
Atto H680 – Avid SAS VideoRAID SR (16-bay) support
Atto R380 – Avid SAS VideoRAID ST (5-bay) support
Atto R380 – SAS Xtore StudioRAID 5Ti (5-bay) support
LSI 9200-8e SAS Xtore 16Re (16-bay) support
LSI 9200-8e SAS Xtore 5Te (5-bay) support
Atto UL5D - Legacy u320 SCSI support
OR
Shared Storage Controller:
Myricom
10G-PCIE-8B-S
HP NM980AV 1394a PCI HBA
Primary 1394 connection for 1394 camera / deck / disk drive
(1394 disk drives are recommended only for file transfers)
Do Not Use. Will cause BUS contention with 1394 controller installed in slot #5.
Embedded
Broadcom
BCM5764
GbE NIC
PCI-E x1
Gen 1
Not qualified for Avid ISIS 5000 / 7000 Connectivity
Qualified for Avid MediaNetwork AECIFs
Page 5 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
6.) Utilization of the Z400
3-port PCI 1394a Firewire IEEE HBA option
ports for Camera / Deck / Disk Drive support
- NM980AV HP 3-port PCI 1394a Firewire IEEE HBA option. Installs in slot 5, has two external rear 1394a ports and
also connects to Z400 front panel 1394a port.
Media Composer 6.0 and NewsCutter 10 do not support Avid 1394 hardware such as Adrenaline and 1394 Mojo-
SDI. This simplifies utilization of the Z400 embedded 1394 port. The embedded 1394 ports can and should be used for all 1394 Camera / Deck / Disk Drive connectivity for all configurations running Media Composer 6.0 and NewsCutter 10.
Configuration
Avid DX Hardware
NM980AV HP 3-port PCI 1394a Firewire IEEE HBA option
(Slot #5)
Utilization for
Camera / Deck / Disk Drive support
Yes
- Supports 1394 Deck / Camera / Disk Drive
(
1394 disk drives are recommended only for file transfers)
Software Only
Yes
- Supports 1394 Deck / Camera / Disk Drive
(
1394 disk drives are recommended only for file transfers)
3
Vendor Qualified rd
Party PCIe Hardware
Yes
- Supports 1394 Deck / Camera / Disk Drive
However 3 rd
party hardware and a 1394 Camera or
Deck cannot be simultaneously connected.
(
1394 disk drives are recommended only for file transfers)
Slot #5 NM980AV HP 3-port PCI 1394a Firewire IEEE HBA option (also connects internally to Z400 front panel 1394 port).
Primary 1394 connection for Deck / Camera / Disk Drive
Page 6 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
7.) HP Z400 I/O Slot Layout
HP Z400 Slot Layout
Page 7 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
8.) Various Configuration Issues:
A.) D/X hardware configs –
All 3 versions of the DX interface HBA are supported with the Media Composer 6.x and NewsCutter 10.x releases
1) Active DX interface HBA 7030-30048-01
2) Active DX interface HBA 7030-20084-01
3) Passive DX interface HBA 7030-30021-01
Active DX interface HBA 7030-30048-01 Active DX interface HBA 7030-20084-01
Passive DX interface HBA (7030-30021-01)
Page 8 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
B.) Qualified Avid system BIOS settings and version(s): (As of this writing):
I t is recommended that the BIOS be updated to an “AVID Qualified” BIOS.
Failure to update the Z400 to an
“Avid qualified BIOS” may result in non-optimal operation of the AVID software and hardware.
- Minimum BIOS ver 1.06
-
Also qualified ver 1.14, ver 1.17, ver 3.07, ver 3.12, ver 3.12, ver 3.15, ver 3.16, ver 3.19, ver 3.20,
ver 3.21 (preferred)
Current Avid qualified Z400 BIOS information is maintained at the following Avid KB link: http://avid.custkb.com/avid/app/selfservice/search.jsp?DocId=267609&Hilite=hp+bios
Z400 Required system BIOS settings:
1. Set CPU Processors Hyper-Threading – Enable
2. Set Runtime Power Management – Disable
3. Set MWAIT-Aware OS – Disable
4. Set Idle Power Savings – Normal
Z400 Optional system BIOS change:
1. Set Intel Turbo Boost Technology
**
– Disable
**
Only required if connecting USB audio I/O devices. This setting will eliminate any audio
“motor-boating” or audio “popping” which may be experienced with USB audio I/O devices.
See Instructions on how to set Z400 BIOS settings on the next page:
Page 9 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Set Z400 Required system BIOS settings:
- During boot up press F10 at the HP splash screen to invoke Set Up.
- Select the Advanced tab
- Select Processors. <Enter>
- Default setting is Disable
Change this setting from Disable to Enable
- Hi F10 to save the Hyper-Threading setting
- Select the Power tab
- Select OS Power Management <return>
- Select Runtime Power Management
- Default setting is Enable
Change this setting from Enable to Disable
- Select MWAIT-Aware OS
- Default setting is Enable
Change this setting from Enable to Disable
- Select Idle Power Savings
- Default setting is Extended
Change this setting from Extended to Normal
- Hi F10 to save the Runtime Power Management, MWAIT-Aware OS, and Idle Power Savings
- Press F10 twice to Save
- Save Changes and Exit
- System will Reboot
Set Z400 Optional system BIOS setting:
- Select the Power tab
- Select Hardware Power Management <Enter>
- Select Intel Turbo Boost Technology
- Default setting is Enable
Change this setting from Enable to Disable
- Press F10 twice to Save
- Save Changes and Exit
Page 10 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
C.) Nvidia Qualified Drivers:
Nvidia qualified drivers
AVID Software
Media Composer
Version(s)
6.0 and later
Nvidia GPU
Quadro FX 3800
Nvidia Driver Required
275.89
NewsCutter 10.0 and later Quadro FX 3800 275.89
After installation of the AVID software the supported Nvidia driver can be found in the following directory:
Program Files / Avid / Utilities / Nvidia
Set optimized Nvidia driver settings for Avid editing environments:
1. See picture below
2. Right-Click on the desktop and select Nvidia Control Panel
3. Select the “Desktop” menu selection in the control panel menu bar.
4. Enable “Desktop -> Video Editing Mode
Page 11 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
5. Select Manage 3D Settings
6. Select “Global Settings” Tab
7. Under the “Global Settings” tab select “Base Profile” as shown in the picture below:
Page 12 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
8. Scroll down and locate the “Power Management Mode” feature. The default setting is “Adaptive” as shown in the picture below.
Page 13 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
9. For the “Power management mode” feature, select “Prefer maximum performance” as shown in the picture below.
10. Depress the “Apply” button.
Page 14 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Make the following setting for “Multi-display/mixed-GPU acceleration”
11. Stay in the “Manage 3D Settings” and “Base Profile” area
12. Select “Global Settings” Tab
13. Scroll down and locate the “Multi-display/mixed-GPU acceleration” feature. See picture below. The setting should be set to “Multiple display performance mode”. If not set properly, select Multiple display performance mode and depress the “Apply” button. (The other settings are “Single display performance mode” and “Compatibility performance mode”. These settings are not recommended for
Avid editing environments).
Page 15 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Make the following additional setting for “3D App-Video Editing”
14. Stay in the “Manage 3D Settings” area
15. Select “Global Settings” Tab
16. Under “Global Settings” tab select “3D App-Video Editing” setting as shown in picture below:
17. Depress the “Apply” button
18. Nvidia driver optimization settings for Avid environments are complete.
Page 16 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
D.) Nvidia Quadro GPU monitor connectivity:
The Nvidia Quadro FX 3800 graphics card has a single DVI port and two Display-Port ports
(Important: Display-ports are not HDMI ports; at first glance they do look very similar to HDMI ports)
( Please Note: Only two of the three video ports can simultaneously be used. Connecting to all three video ports at the same time will result in non-functioning video output from the Nvidia GPU video card.)
The HP Z400 includes one Display-Port-to-DVI adapter. HP P/N 481409-001
For dual monitor connectivity:
1. Use the DVI port and one Display-Port (Display-Port connection can be native display-port to monitor via display-port connection, or use the display-port-to-DVI-adapter supplied with the system to connect to a native
DVI monitor).
2. Or use two Display-Ports (Requires monitors with native display-port connections, two display-port to DVI adapters are not recommended when using dual display-port connections).
Reference picture Quadro FX 3800
DVI Port
Display Ports
Page 17 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
E.) Serial Port Deck Control:
The HP Z400 workstation does not have an embedded serial port. Serial port deck control can be established via two methods (both of which have been qualified by Avid and will maintain frame accuracy in Avid environments)
USB port of the Z400 directly to the RS422 port of a deck.
http://www.addenda.com/addenda-elect/products/rsUSB4.php
2. Combination of a Keyspan (Tripp-Lite) Model USA-19HS USB-to-serial-port adapter with Addenda Rosetta
Stone model RS – 2/8 RS232-to-RS422 converter
- Keyspan (Tripp-Lite) Model USA-19HS (AVID P/N 7080-20013-01) http://www.tripplite.com/en/products/model.cfm?txtSeriesID=518&EID=13384&txtModelID=3914
- Addenda Rosetta Stone (or equivalent) model RS – 2/8 RS232-to-RS422 converter (AVID P/N
7070-00507-01) http://www.addenda.com/addenda-elect/products/rs28.php
To connect the Keyspan 19HS / Addenda RS -2/8 combination:
- Install the Keyspan 19HS driver before plugging the device into a Z400 USB port.
- Once the Keyspan 19HS driver is installed then plug the Keyspan 19HS into a Z400 USB port.
- The Keyspan 19HS will now show up in device driver.
- Using a serial cable, connect the 9-pin serial port of the Keyspan 19HS USB adapter to the port of the
Addenda marked RS232 from PC
- Using a 2 nd
serial port cable connect the port of the Addenda marked “RS422 to VTR” to the deck control serial port of the deck.
F.) O.S. setting recommendations for optimum performance with Avid Editing applications:
The following links provide O.S. setting suggestions for ensuring optimum performance when working with your Avid editing application with a Windows operating system.
- Optimizations for Video Editors - Windows 7
http://avid.custkb.com/avid/app/selfservice/search.jsp?DocId=390339
Page 18 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
G.) Set Windows “Visual Effects” for “best performance”:
1. Right-Click on My Computer / Computer
3. The screen below will be displayed:
4. On the left side of the screen above, locate and select “Advanced system settings”
Page 19 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
5. The System properties window will be displayed. (Picture below).
6. Under the “Advanced” tab depress the “Settings...” button for performance.
Page 20 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
8. Under the “Visual Effects” tab select the “Adjust for best performance” selection. (Picture below).
9. Depress the “Apply” button
10. Reboot Windows
11. Required Windows visual performance settings for Avid environments are now complete.
Page 21 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
H.)
ATTO UL5D issue: When an ATTO UL5D PCI-E u320 SCSI controller is installed in slot #5, the UL5D BIOS must be disabled or the following warning may be reported during system boot: (Also the UL5D BIOS must be disabled for proper operation when connected to an AVID VideoRAID RTR u320 SCSI).
110 – Out of memory space for option ROMS.
The option ROM for the following device was unable to run due to memory constraints. If you choose to continue, one or more
PCI devices may not work properly
To disable the UL5D BIOS and eliminate the above warning, perform one of the following:
A. AVID Knowledge Base article 273945, http://avid.custkb.com/avid/app/selfservice/search.jsp?DocId=273945&Hilite=UL5D
Install Atto UL5D configuration tool and launch the software.
Expand the Express PCI UL5D menu, and click on Channel.
The Boot Driver has to be disabled on both channels of the UL5D.
Configure the UL5D per this screenshot, and do this for both Channel 1 and Channel 2
B. Or during system boot perform the following:
1.
Reboot the system
2.
Hit “Escape” to clear the HP splash screen
3.
Hit Ctrl-Z when the following Atto UL5D BIOS message prompts
*********************************************
** ATTO ExpressPCI ™ Version 2.10 **
***** Press [Ctrl + Z] for Setup Utility *****
4.
Select 1 - Adapter menu
5.
Select 2 - Configure Both Adapter Channels
6.
For ver 2.10 firmware
‐ Select Host Adapter BIOS
‐ Select “Disabled” using [Page Up] / [Page Down]
7.
For ver 2.27 firmware
‐
Select Boot Driver
‐
Select “Disabled” using [Page Up] / [Page Down]
8.
Press “ESC”
9.
Press “ESC”
10.
Select 4 – Save Parameters and Exit
Page 22 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
I.) Intel PRO 1000 PT for ISIS connectivity: For proper operation and connectivity of the Intel PRO 1000 PT with ISIS the following are required:
1. For the Intel PRO 1000 PT driver, under the performance settings, change the following parameters:
- Receive Buffers to 1024
- Transmit Buffers to 1024
2. Disable the windows firewall.
Intel PRO 1000 PT Driver: The proper driver can be found in the ISIS software directory: Tools_3rdParty / Drivers_and_Firmware
To set the Intel PRO 1000 PT Receive / Transmit buffers:
Go to device manager and select each instance of the device named Intel(R) PRO/1000 PT Dual Port Server Adapter which will be used for ISIS connectivity.
Select performance options and then select Properties.
Page 23 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Set Receive Buffers to 1024 Set Transmit Buffers to 1024
Perform this for each instance of the device named “Intel(R) PRO/1000 PT Dual Port Server Adapter” which will be used for ISIS connectivity.
J.)
Disable the windows firewal l:
Navigate to Control Panel / Windows Firewall -- Select Turn Windows Firewall on or off
Page 24 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
Select Turn off windows firewall in both network locations, OK to save
Update
Initial public release of the Z400 Gen1 configuration guide for support of Media Composer 6.0 and NewsCutter 10
Revision Update
Revision Date
A Oct 27 th
, 2011
Name
Joe Conforti
Page 25 of 25 Joe Conforti
– Avid Technology – Oct, 27th, 2011
Z400 Gen1 (4-DIMM / No Embedded Firewire) Rev A Config Guide
