WinSystems PPM-GIGE PC/104-Plus Dual Gigabit Ethernet module Datasheet
WinSystems PPM-GIGE, a high-performance PC/104-Plus compliant Gigabit Ethernet module, allows connection to 10, 100, and 1000 Mbps networks using standard CAT 5 twisted pair copper cables. It supports Windows, Linux, and other x86-compatible operating systems and features automatic switching between speeds and full- and half-duplex operation. With an RJ-45 Ethernet interface connector and monitor LEDs for visual status indication, it provides a reliable and versatile networking solution for various industrial applications.
Advertisement
Advertisement
PPM-GIGE-1
PC/104-Plus Gigabit Ethernet
Controller Module
Features
• IEEE 802.3 support for 1000BASE-T, 100BASE-TX, and
• Automatic switching from 1 Gbps to 100 or 10 Mbps
and full- and half-duplex operation
• Realtek RTL8110 Gigabit Ethernet PCI controller
• Auto-Negotiation with Next Page capability
• IEEE 802.3x-compliant full duplex fl ow control support
• Adaptive equalization supported
• 64Kbyte Rx and 8K Tx packet FIFO
• PHY supports 2-pair and 3-pair cable downshift
• RJ-45 Ethernet interface connector on board
• Support for Windows®, Linux, and other x86 RTOS
• LEDs provide visual status indication
• Small size, 3.6 x 3.8 inches (90 x 96mm)
• PC/104-Plus Bus compliant
• Single +5V supply
• Operates from -40°C to +85°C
PPM-GIGE-1 Block Diagram
Product Description
The PPM-GIGE-1 is a high-performance, PC/104-Plus compliant Gigabit Ethernet module. This add-in module allows connection to 10, 100, and 1000 Mbps networks using standard CAT 5 twisted pair copper cables. It is based upon the popular Realtek RTL8110 controller that is supported by a wide range of operating systems including Windows,
Linux, and other x86-compatible operating systems.
The Realtek RTL8110 Gigabit Ethernet controller combines a triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, 32-bit
PCI bus controller, and embedded memory. With stateof-the-art DSP technology and mixed-mode signal technology, it off ers high-speed transmission over CAT 5
UTP or CAT 3 UTP (10 Mbps only) cable. Functions such as
Crossover Detection & Auto-Correction, polarity correction, adaptive equalization, cross-talk cancellation, echo cancellation, timing recovery, and error correction are implemented to provide robust transmission and reception capability at high speeds.
The device supports the 32-bit PCI v2.2 interface for host communications and is compliant with the IEEE 802.3 specifi cation for 10/100 Mbps Ethernet and the IEEE
802.3ab specifi cation for 1000 Mbps Ethernet.
WinSystems | 715 Stadium Drive, Arlington, TX 76011 USA | Tel 817-274-7553 | [email protected] | www.WinSystems.com
PPM-GIGE-1 - PC/104-Plus Gigabit Ethernet Module
Integrated PHY - The PHY supports 10/100/1000 Mbps full- and half-duplex operation. IEEE 802.3ab Autonegotiation support provides automatic link confi guration of speed, duplex, and fl ow control.
Ethernet Connection - The PPM-GIGE-1 is hooked to the network through an onboard RJ-45 connector.
Monitor LEDs - Light emitting diodes (LEDs) are on the
PPM-GIGE-1 to provide a visual indication of the link status, network activity and network speed. The red LED is On if the link is at 10 Mbps and blinks if data is being transferred.
The yellow LED is ON when the link is established at 100MB and then blinks when packets are being sent or received.
Similarly, the green LED is ON when the link is established at 1 Gbps and then blinks when packets are being sent or received. If no link is established, all LEDs will be OFF. If a link is established but there is no activity one and only one
LED will solid ON and the color of the LED will indicate the channel link speed.
Software - Most PCI-compatible drivers, utilities and
10/100/1000 Ethernet supported operating systems based on the RTL8110 will work directly with this module.
Power Supplies - There are three independent power supplies on this module for use by the RTL8110 controller.
They are 3.3V, 1.8V, and 1.2V. The PPM-GIGE-1 requires only a single +5 volt input. The +5V input power and ground for the board is supplied from both the PC/104 and PC/104-
Plus connectors.
PC/104-Plus Interface - The PPM-GIGE-1 module is designed to off er fl exible, high-performance Ethernet networking capability. It provides 32-bits of addressing and data, as well as the complete control interface to operate on the PC/104-Plus Bus. The chip has a PCI Bus master interface and is compliant with the PCI Bus Specifi cation
Revision 2.2.
The PPM-GIGE-1 is designed to support 3.3V PC/104-Plus signaling. There is a jumper block on board to select the module slot position and system resources. Also, there is a PC/104 connector on the board. It feeds the signals through the connector to the next module in a stack.
Other Confi gurations - WinSystems off ers a dual channel version of this board called the PPM-GIGE-2. Also available is a dual channel with Power over Ethernet (POE) support called the PPM-GIGE-2-POE. Visit our website for the detailed specifi cations.
Front and Back Picture of PPM-GIGE-1
Electrical
Data rate
Technical Specifi cations
10/100/1000 megabits per second
Power Requirements
Vcc = +5V ±5% @ 250 mA typical
Connectors
Ethernet
PC/104-Plus
PC/104
RJ-45
120-pin (4 x 30; 2mm) stackthrough
16-bit stackthrough (feed through only)
Environmental
Operational from -40°C to +85°C
Non-condensing relative humidity 5% to 95%
RoHS compliant Yes
Mechanical
Dimensions
Weight
3.6 x 3.8 inches (90 x 96mm)
2.9 oz. (81 gm)
Ordering Information
PPM-GIGE-1 PC/104-Plus Gigabit Ethernet module
WinSystems reserves the right to make changes to products and/or documentation without further notifi cation.
Product names of other companies may be trademarks of their respective companies.
WinSystems | 715 Stadium Drive, Arlington, TX 76011 USA | Tel 817-274-7553 | [email protected] | www.WinSystems.com

Public link updated
The public link to your chat has been updated.
Advertisement