Electrician - TradeIndia
TRADE: ELECTRICIAN
Sl.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
TOOL KIT
Specification of Items
Steel Tape, 10 m length
Plier Insulated, 150 mm
Plier Side Cutting, 150 mm
Screw Driver,
100 mm
Screw Driver, 150 mm
Electrician Connector, screw driver insulated handle thin stem, 100 mm
Heavy Duty Screw Driver , 200 mm
Electrician Screw Driver thin stem insulated handle, 250 mm
Punch Centre , 150 mm X 9 mm
Knife Double Bladed Electrician
Neon Tester
Steel Rule 300 mm
Hammer, cross peen with handle
Hammer, ball peen With handle
Gimlet 6 mm.
Bradawl
Scriber (Knurled centre position )
Pincer 150 mm
Qty
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
17 Nos.
SHOP TOOLS, INSTRUMENTS &
MACHINERY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
C- Clamp 200 mm, 150 mm and 100 mm
Spanner Adjustable 150 mm, 15 degree
Blow lamp 0.5 ltr
Melting Pot
Ladel
Chisel Cold firmer 25 mm X 200 mm
Chisel 25 mm & 6 mm
Hand Drill Machine 0 to 6 mm capacity
Portable Electric Drill Machine 6 mm capacity
Pillar Electric Drill Machine 12 mm capacity
Allen Key
Oil Can 0.12 ltr
Grease Gun
Out Side Micrometer 0 to 25 mm
Motorised Bench Grinder
Rawl plug tool & bit
Pully Puller
Bearing Puller
Pipe vice
Thermometer 0 to 100 deg Centigrade
Scissors blade
150 mm
Crimping Tool
Wire stripper 20 cm
Chisel Cold flat 12 mm
Mallet hard wood 0.50 kg
Hammer Exeter type 0.40 kg
Hacksaw frame 200 mm 300 mm adjustable
Try Square 150 mm blade
Outside & Inside Divider Calliper
Pliers flat nose 150 mm
Pliers round nose 100 mm
Tweezers 100 mm
Snip Straight & Bent 150 mm
D.E. metric Spanner
2 Nos each
2 Nos each
1
1
1No
2
2 Nos each
1
1
1
1 set
1
1 No
2
1
2 set
2
2
4
1 No.
4 Nos.
2 sets
2 Nos.
2 Nos.
4 Nos.
4 Nos.
2 Nos. each
4 Nos.
2 Nos. each
4 Nos.
4 Nos.
4 Nos.
2 Nos. each
2 Nos.
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Drill hand brace 0 to 100 mm
Drill S.S. Twist block 2 mm, 5 mm 6 mm set of 3
Plane, smoothing cutters 50 mm
Gauge, wire imperial
File flat 200 mm 2nd cut
File half round
200 mm 2nd cut
File round 200 mm 2nd cut
File flat 150 mm rough
File flat 250 mm bastard
File flat 250 mm smooth
File Rasp, half round 200 mm bastard
Soldering Iron 25 watt, 65 watt, 125 watt
Copper bit soldering iron 0.25 kg.
Desoldering Gun
Hand Vice 50 mm jaw
Table Vice 100 mm jaw
Pipe Cutter to cut pipes upto 5 cm. dia
Pipe Cutter to cut pipes above 5 cm dia
Stock and Die set for 20 mm to 50 mm G.I. pipe
Stock and Dies conduit
Ohm Meter; Series Type & Shunt Type
Features :
Auto range
200mohms, 2ohms, 20ohms, 200ohms, 2kohms, 20kohms,
200kohms
Resolution 10micro ohms
Single/Repent measuring
Four terminal measuring
Percentage error three steps selectable
Dual Display
+(0.5%+2digit) LED Display sampling rate 17 Times/s
4 Nos.
4 Set
2 Nos. each
2 Nos.
8 Nos.
4 Nos.
4 Nos.
4 Nos.
4 Nos.
4 Nos.
4 Nos.
2 Nos. each
2 Nos.
4 Nos.
4 Nos.
8 Nos.
4 Nos.
2 Nos.
1 set
1 No.
2 Nos. each
Technical Specification
Measuring range:200mohm, 2ohm, 20ohm, 200ohm, 2kohm,
20kohm 200kohm
Output current:100mA at 200mohm, 2ohm
:10mA at 20ohm
:1mA at 200ohm
:100microA at 2kohm, 20kohm
:10microA at 200kohm
Resolution: 10micro ohmat 200mohm , 2ohm
:0.1micro ohm
at 20ohm
:1mohmat 200ohm
:10mohmat 2kohm
:100mohmat 20kohm
:1ohmat 200kohm
Open circuit voltage
: <1.0V
at 200mohm, 2ohm, 20ohm
:<4.0V at 200ohm, 2kohm, 20kohm, 200kohm
Power requirement: 220 VAC +10% , 50 Hz
Weight
: 3.0Kg Approx.
Dimensions (mm): 280(L) x 220(B) x 90(H)
Standard Accessories :
Power cable, Instruction manual
56
Multi Meter (analog) 0 to 1000 M Ohms, 2.5 to 500 V
Technical Specification
Test voltage
:
250/500/1000/2500V
Insulation resistance
:
0.1Mohm~20Gohm
Accuracy
:
+(3%Rdg+5Digit)
Resolution
:
0.01Mohm
AC Voltage range :
600VAC
Accuracy
:
+(2%Rdg+5Digit)
Weight : 1.0Kg Approx.
2 Nos.
Dimensions (mm) : 190(L) x 155(B) x 75(H)
Standard Accessories :
Probes, Batteries, Instruction manual
57
Digital Multi Meter
Features :
LCD Display, Max. Upto 1999
Manual operation
Diode test, Continuity test, Low Battery indication, Shock protection
6 Nos.
Measure AC, DC Voltage & DC Current
Technical Specifications:
DC Voltage range : 200mV, 2V, 20V, 200V, 600V
Accuracy :+(0.5% + 4 Digit)
DC Current range: 200mA, 2mA, 20mA, 200mA, 10A
Accuracy:+(1.5% + 3 Digit)
AC Voltage range:200V
, 600V
Accuracy:+(1.2% + 10 Digit)
Resistance range:200ohm, 2Kohm, 20Kohm, 200Kohm, 20Mohm
Accuracy:+(0.8% + 5 Digit)
Input impedance:1M ohm
Sampling Rate:3s
AC Frequency Response :40 ~ 200Hz
Power requirement: Battery 9V (Included)
Standard Accessories :
Probes, Batteries, Instruction manual
58
59
60
61
62
63
64
65
66
67
A.C. Voltmeter M.I. 0 –500V A.C
1 No.
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
Milli Voltmeter centre zero 100 – 0 – 100 m volt
1 No.
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
Milli Voltmeter centre zero 100 – 0 – 100 m volt
1 No.
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
Ammeter MC 0-5 A, 0- 25 A
1 No. each
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
A.C. Ammeter M.I.. 0-5A, 0-25 A
1 No. each
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
Kilo Wattmeter 0-1-3 kw
1 No.
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
A.C. Energy Meter,Single phase 5 amp. Fitted on Wooden Board and Terminal
1 No. each
provided
A.C. Energy Meter Three Phase 15 amp. Fitted on Wooden Board and
1 No.
Terminal provided
Power Factor Meter
1 No.
Housed in a ABS Plastic case precision grade with a Bakelite box
terminal
Three Phase, Four Wire Dynamometer Type Portable Power Factor
Meter
range : Current Coil/Potential Coil : 2.5A/250V
Frequency Meter, LCD Type fitted into box 96x96mm
1 No.
Flux Meter
1 No.
Digital Gauss meter
The Gauss meter operates on the principle of Hall Effect in
Semiconductors.
The small Hall voltage is amplified through a high stability
amplifier that a millivoltmeter connected at the output of the amplifier can
be calibrated directly in magnetic Field unit.
Technical Specifications :
Range : 0-2K gauss and 0-20 Kg
Resolution : One Gauss at 0-2 K gauss range
Accuracy : ± 0.5%
Display : 3 ½ digit 7 seg. (DPM)
Detector : Hall probe with an imported hall element
Power : 220V, 50 Hz
Special : Indicate the direction of the magnetic field.
68
69
70
71
72
73
74
75
76
77
78
Wheat Stone Bridge with galvanometer & battery
Technical Specification
Series Arm : Four decade dial in steps of 1000 Ohm, 100 Ohm, 10 Ohm ,
1 Ohm .
Ratio Arm : The ratio arm of bridge are capable of Selecting multiplying
factor of 0.001, 0.01, 0.1, 1, 10, 100,1000 for resistance measurement &
varley loop test & ratio M10, M100, M1000 for Murray loop test.
One selectable switch with option for Murray (M) loop & For
resistance/Varley (VR) loop test.
One galvanometer fitted inside the box with option of external or internal
galvanometer with terminal .
Two press keys provided marked as initial & final.
Two toggle switches are provided one for internal or external battery and
other for direct or shunted sensitivity of galvanometer.
Laboratory Type Induction Coil
DC Power Supply 0-30V 2 Amp
Technical Specifications:
Variable Output
Output Voltage :0 ~ 30VDC
Output Current :0 ~ 2A
Source Regulation:< 0.05% +10mV
Load Regulation :< 0.05% +10mV
Ripple & Noise :<1mV (rms)
Digital Display
:3 digit voltage & current display
Accuracy
:+1%, +1 Digit
Fixed Output
Output Voltage :Fixed 5VDC/3.3VDC
Output Current :1A
Source Regulation:<5mV
Load Regulation :<15mV
Ripple & Noise :<2mV (rms)
Power requirement: 220 VAC +10% , 50 Hz
Weight : 4.0Kg Approx.
Dimensions (mm) : 120(L) x 250(B) x 150(H)
Standard Accessories :
Power cable, Instruction manual
Rheostat
0 -1 Ohm, 5 Amp
0 -10 Ohm, 5 Amp
0- 25 Ohm, 1 Amp
0- 300 Ohm, 1 Amp
1 Phase Variable Auto Transformer
Technical Specifications:
Variable Auto Transformer 0-270VAC
Input Single Phase 230V
Output Voltage 0-270VAC
Output Current 2 Amps
Battery Charger 2-12V/5A
Hydrometer
Miniature Breaker 16 amp ( Raw Material)
Working Bench 2.5 m x 1.20 m x 0.75 m
Fire Extinguisher CO2, 2 KG
Fire Buckets
1 No.
1 No.
1 No
1 No.
1 No.
1 No.
1 No.
4 Nos.
2 Nos.
2 Nos.
2 Nos each
CTS Second Semester: Electrician
SHOP TOOLS, INSTRUMENTS and
MACHINERY
1
2
Tachometer
Technical Specification :
Measuring range :
Photo/Laser
:
Contact
1 No.
: 5-99,999 RPM
: 5-19,999 RPM,
0.05-999.9m/min (0.2-
6,560ft/min)
Measuring distance:
Photo/Laser
: max.2.0 meters
Measuring angle:
Photo/Laser
: 600
:
Contact
: 1200
Resolution
:0.1 RPM (< 1000 RPM), 1.0RPM (>1000
RPM)
Accuracy
: ±0.05% +1 digit
Laser output:
<1mW, Class II
Sampling time: 1 secretary. (over 6 RPM)
Current Transformer Test Set
secondary rated for 5Amp. Which are intended to be used on 50 Hz.
1 No.
Technical Specification :
The Current Transformer Test set provides the following components1. Separate terminals to connect standard C.T. and Test C.T.
secondaries.
2 Ratio error and phase angle error display
3 Range selecting Switch
4 Polarity check indicator
5 Ammeter to measure current injected in percentage
6 Null detector with sensitivity control
7 Terminals to connect burden box on both std. & under test
8 Aux. power supply to energies electronic null detector
9 High permeability magnetic core
10. Secondary current selector 1A . or 5A
Current Transformer Test Set
Scope of Experimentation:
Draw Magnetising Curve for a Protective CTs, and Check knee Point
Voltage
Technical Specifications:
Graphical LCD Display.
LED Indication.
Aux. ON/OFF Switch.
Current Range Selection - 1A & 5A AC.
Hold Key.
Standard CT & Burden Terminals.
'X' CT & Burden Terminals.
A) Percentage Ratio Error : 0 to 50%
B) Phase Ratio Error : 0-1000 Minutes
C) Input Current : 0.05A to 7.5A AC
F) Indication
: a) Reverse Polarity
: b) 'Std'C.T. Sec.open
: c) 'X' C.T. Sec. Open
: d) Difference Ratios of 'Std' &'X' CT Hi-imbalance
: e) Over Current
: f) Ratio Error Polarity
: g) Phase lag-lead
: h) Phase Error Over Range
- Light in weight.
- High Accuracy.
- Reverse Polarity indication.
- Direct reading from LCD display.
- The Ratio Error is directly given in percentage.
- The Phase Error is directly given in minute.
- Current Injection Set
- Output Variable Current 100Amps, Provided with Digital Current Meter
- Current Transformer 100:5Amps 3nos.
3
Potential Transformer 220/110 Single Phase, Housed in strong steel
cabinate, With one Analog Meter
1 No.
4
5
6
7
Growler
Tong Tester / Clamp Meter
Technical Specification :
DC Voltage range
: 400, 600V
Accuracy
: +1.0%
AC Voltage range
: 400, 600V
Accuracy
: + 1.5%
AC Current range
: 40, 400A
Accuracy
: + 2.0%
Resistance
: 400ohms
Accuracy
: + 1.0%
Clamp size
: 28mm (max.)
Battery
: 1.5V x 2 (Included)
Megger 500 volts Rotary Type Enclosed in Meta Box
Contactor & auxiliary contacts 3phase, 440volt, 16amp
8
Contactor & auxiliary contacts
9
10
11
Limit Switch
Rotary Switch 16 A
Load Bank 5 KW( Lamp Type)
Resistive Lamp Load 5 KW is steps of 200W housed in wooden cabinet on
Bakelite panel.
Steps change with switches
Brake Test arrangement with two spring balance 0 to 25 kg rating
1 No.
Knife Switch DPDT fitted with fuse terminals 16 amp, Brass Contacts
4 Nos.
Knife Switch TPDT fitted with fuse terminals 16 amp, Brass Contacts
4 Nos.
Voltage Stabiliser
1 No.
Input: 150 – 230 volt AC
Output: 220 volt AC
3- point D.C. Starter for Motor Upto 2 HP
1 No.
4- point D.C. Starter for Motor Upto 2 HP
1 No.
Electrical Machine Trainer
1 for 8
12
13
14
15
16
17
18
3 phase, 440 volt, 32 amp.
Objective:
Study the Starting & reversing of single phase induction
motor
Study of load Characteristic of Single Phase Induction
Motor
Study of Magnetizing Curve of DC shunt Generator
Study of Load Characteristics of three phase
Synchronous Generator
Study of Three phase Synchronous Motor
Study Speed Torque Characteristics of single phase
induction motor
Features:
Compact and Easy to use in Electrical Laboratories
Equipped with high Safety Features
Portable and Easy to Install
Elaborated Instruction Manual with Calculated Values
Complete with Panel, Machine etc
Supplied with Patch cords for Interconnections &
Instruction Manual
Control Panel
Technical Specifications:
Control Panel housed in a wooden cabinet in tapered
shape for
better view angle. Meters are mounted on thick Bakelite
front
panel with connection Terminals
Meters : 1 No. Voltmeter range 0-500V AC, Size
96X96mm
: 3 Nos. Ammeter range 0-3A AC, Size
96X96mm
: 2 Nos. Voltmeter range 0-300V DC, Size
1 No.
1 No.
1 No.
1 No.
each
1 No.
each
1 No.
1 No.
1 No.
(4+4)
Units
96X96mm
: 1 No. Ammeter range 0-10A DC, Size
96X96mm
: 1 No. RPM Meter ,Size 48X96mm
DC Source
: 0 - 300V DC/4 Amps (Variable)
DC Drive
: 1 No. Thyristorized DC Drive For Speed
Control
Starter
: 1 No. of Direct Online Starter Suitable
up to 3HP
Protections
: 2 No. MCB / DP of Range 16AMP
Power requirement : 440VAC Three Phase
Standard Accessories:
DC Shunt Motor 2HP 220V, Coupled with AC Alternator
0.5 KW & AC Induction Motor
1HP 3Phase 3HP Induction Motor
Technical Specifications:
DC Shunt Motor
Capacity
:
1HP
Cage :
Steel Body
Class :
E Class
RPM :
1500 Approx
Shaft :
Single
Current
:
6.3 Amp Max
Input Terminal :
Armature (A1, A2) , Field (F1, F2)
Power Requirement:
220V DC, Single Phase
AC Alternator
Technical Specifications:
Capacity
:
0.5 KW
Cage :
Steel Body
Class :
E Class
RPM :
1500 Approx.
Shaft :
Single
Current
:
2.2 Amp Max
Input Terminal :
R, Y, B and neutral with F1 and
F2(Field Terminal)
Output Voltage :
415~440V AC, 50Hz, Three
Phase
Single Phase Induction Motor
Technical Specifications:
Capacity
:
1 HP
Cage :
Steel Body
Class :
E Class
RPM :
1500 Approx.
Shaft :
Single
Current
:
3.2 Amp Max
Input Terminal :
Phase & Neutral
Input Voltage :
220~240V AC, 50Hz, Single
Phase
Three Phase squirrel cage Induction Motor
Technical Specifications:
Capacity
:
3HP
Class :
E Class
RPM :
1500 Approx.
Input Terminal :
Phase & Neutral
Input Voltage :
440VAC, 50Hz, Single Phase
19
Motor-Generator (AC to DC) consisting of :
A laboratory type model for conducting various experiments.
Technical Specification :
MOTOR :
1 No.
Squirrel cage Induction motor 7 H.P.415 volts,3 phase 50 Hz 1440 R.P.M.
type TEFC cont. rating. Insulation class 'F',Horizontal foot mounted. 6
terminals brought out in the terminal box for connection.
GENERATOR :D.C.shunt generator : 5 K.W. 440 V. S
Self excited
: 1440 R.P.M.
type continuous rating Insulation class 'F'. Horizontal.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front
side of 6mm thick
bakelite sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywoodfitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
Educational type backelite insulated banana terminals provided for supply
and motor generator connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
A.C.SIDE :
1) Voltmeter M.I.Type 0-500 volts, 96 x 96 mm : 1 no.
2) Ammeter M.I.Type 0-15 Amp.96 x 96 mm : 1 no.
3) Rotory Switch for voltmeter select for OFF/RY/YB/BR 16 Amp.,440 v :
1 no.
4) Automatic STAR / DELTA Starter suitable for above motor flush
mounted : 1 no.
5) Bakelite based HRC fuses of suitable capacity
: 3 Nos
6) RCCB of Suitable capacity (ISI) marked
: 1 no.
7) Indicating lamp LED type 12 mm size Red, Yellow, Blue colour : 1
no.each
D.C.SIDE :
1) Voltmeter M.C,Type 0-500 volts,96 x 96mm
2) Ammeter M.C.Type 0-15 Amp.96 x 96 mm
3) Ammeter M.C.Type 0-1.5 Amp.96 x 96 mm
4) Field regulator disc type suitableto decrease
min.Amps :1 no.
5) D.P.S.T. Knife Switch. 20 Amp. 440 v
: 1 no.
6) Indicating lamp LED type Red, colour 12mm size
: 1 no.
: 1 no.
: 1 no.
field current up to
: 1 no.
BASE PLATE :
Motor and Generator will be mounted on fabricated base plate of M.S.'C'
channel
20
21
COUPLING :
Motor and Generator are coupled with a flexible coupling & mounted on a
common base plate.Coupling guard & antivibration mounts are also
provided.
Used DC Generators-series, shunt and compound type for overhauling
practice. Should be in working condition.
D.C. Shunt Generator, 2.5 KW, 220V with control panel
A laboratory type model for conducting various experiments.
TECHNICAL SPECIFICATION :
GENERATOR
D.C. Shunt Generator 2.5 kw, 230 volts, 1500 R.P.M., continuous rating,
Insulation Class "B", Horizontal foot mounted, All the terminals are
1 No.
each
1 No.
brought out to the terminal box.
Prime Mover:
3 phase 5 hp induction motor as prime mover for generator
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided for
supply and generator connection.
Circuit diagram of panel provided inside the panel. All accessories
connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
1) Voltmeter M.C. type 0-300 volts, 96 x 96 mm : 1 no.
2) Ammeter M.C. type 0-15 Amp., 96 x 96 mm : 1 no.
3) Ammeter M.C. type 0-1.5 Amp., 96 x 96 mm : 1 no.
4) Field regulator disc type suitable to decrease field current upto min.
Amp : 1 no.
5) DPST Knife Switch- 20 Amps., it mounted on the Panel Board : 1 no.
6) Indicating lamp LED type Red, colour 12mm size : 1 no.
PAINT :
Generator will be painted with two coats of smoke gray oil paint
and panel board will be powder coated.
BASE PLATE :
Motor & Generator mounted on fabricated base plate of M.S.'C' channel
size 75 x 40 x 6 mm thick. Base plate
22
D.C. Compound Generator 2.5 KW
A laboratory type model for conducting various experiments.
TECHNICAL SPECIFICATION :
GENERATOR
D. C. Compound Generator 2.5 kw, 230 volts, 1500 R.P.M., continuous
rating, Insulation Class "B", Horizontal foot mounted, All the terminals are
brought out to the terminal box.
Prime Mover:
3 phase 5 hp induction motor as prime mover for generator
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size
W=900 mm ; D=250 mm ; H=750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W
= 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
1 No.
30 A. Educational type backelite insulated banana terminals provided for
supply and generator connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc
The Instrument Panel consist of following accessories :
Voltmeter M.C. type 0-300 volts, 96 x 96 mm : 1 no.
Ammeter M.C. type 0-15 Amp., 96 x 96 mm : 1 no.
Ammeter M.C. type 0-1.5 Amp., 96 x 96 mm : 1 no.
Field regulator disc type suitable to decrease field current upto min.
Amp : 1 no.
DPST Knife Switch - 20 Amps., it be mounted on the Panel Board : 1 no.
Indicating lamp LED type Red, colour 12mm size : 1 no.
Fuses H.R.C. Backelite type base with top 16A 230 V. : 2 nos.
PAINT : Generator and pannel board painted with two coats of smoke
gray oil paint
23
24
BASE PLATE : Motor & Generator mounted on fabricated base plate of
M.S.'C' channel size 75 x 40 x 6 mm thick.
Base plate lenghth 800 mm for Primemover coupling.
Diesel Generator Set with change over switch, over current breaker and
water-cooled with armature, star-delta connections
AC 3 phase, 5 KVA, 230 volt
Motor series DC, 220 Volt, 0.5 to 2 HP, coupled with mechanical load
A laboratory type model for conducting various experiments.
TECHNICAL SPECIFICATION :
MOTOR :
2 HP,220 volts,1500 RPM coupled with mechanical on load, ‗F' class
insulation, continuous rating
S.P.D.P.type,
horizontal
foot
mounted.
Educational type Suitable friction brake Dynamometer set having 2 Nos.
spring balances & belt provided with fixed with motor base plate
1 No.
1 No.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
1) Two point starter suitable foe series D.C. motor flush mounted.
2) Indicating lamp, LED type 12mm size for incoming & outgoing supply.
3) DPST knife Switch, 20 A,
4) D.C.M.C. Ammeter 0-10A,96 x 96 mm sq.type, flush type
5) D.C.M.C. voltmeter 0-300 v, 96 x 96 mm sq.type, flush type
6) Fuses kitkat 16 A, 500 v inside the pannel.
BASE PLATE :
Motor with mechanical load will be mounted on fabricated base plate of
M.S. Motor with mechanical load mounted on fabricated base plate of
M.S.'C' channel.
25
PAINT :
Motor painted with two layers of smoke gray oil paint. & control panel
powder coated.
Motor shunt DC 220 Volt, 2 to 3 HP
1 No.
TECHNICAL SPECIFICATION :
MOTOR :
D.C. Shunt motor 2 H.P., 220 volts,1500 R.P.M., continuous rating class
of insulation 'B' S.P.D.P. Type, Horizontal foot mounted, confirming to
standards , All the terminals are brought out to the terminal box.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W
= 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
1) Three point D.C. starter suitable for above motor, flush mounted : 1 no.
2) D.P.S.T. Knife Switch. suitable for above motor : 1 no.
3) Indicating lamp LED type 12 mm size for incoming and outgoing supply
of the pannel board : 2 nos.
4) Voltmeter M.C. 0-300 volts D.C. size 96 x 96 mm : 1 no.
5) Ammeter M.C. 0-15 Amp. D.C. size 96 x 96 mm : 1 no.
6) Ammeter M.C. 0-1.5 Amp. D.C. size 96 x 96 mm : 1 no.
7) Field regulator suitable to keep constant rated R.P.M. of the motor at
full load. : 1 no.
BASE PLATE :
Motor mounted on fabricated base plate of M.S.'C' channel .
26
PAINT :
Motor painted with two coats of smoke grey oil paint, panel board and
angle stand powder coated.
Motor DC compound wound 220 volt 2 to 3 HP with starter and
switch
A Laboratory Type Model For Conducting Various Experiments.
TECHNICAL SPECIFICATION :
MOTOR :
D.C. compound motor 2 H.P., 220 volts,1500 R.P.M., continuous rating
class of insulation 'F' S.P.D.P. type, Horizontal foot mounted, Confirming
to I.S. 4722-1992, All the terminals are brought out to the terminal box.
CONTROL DESK :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
1 No.
27
28
29
30 A. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel. All accessories
connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
1) Four point D.C. starter suitable for above motor, flush mounted : 1 no.
2) D.P.S./T. Knife Switch. suitable for above motor : 1 no.
3) Indicating lamp LED type 12 mm size for incoming and outgoing supply
of the pannel board : 2 nos.
4) Voltmeter M.C. 0-300 volts D.C. 96x96mm size : 1 no.
5) Ammeter M.C. 0-15 Amp. D.C. 96x96mm size : 1 no.
6) Ammeter M.C. 0-1.5 Amp. D.C. 96x96mm size : 1 no.
7) Field regulator suitable to keep constant rated R.P.M. of the motor at
full load. : 1 no.
BASE PLATE :
Motor mounted on fabricated base plate of M.S.'C' channel.
PAINT :
Motor painted with two coats of smoke grey oil paint, panel board and
angle stand powder coated.
SINGLE PHASE TRANSFORMER, AIR COOLED
TRANSFORMER SINGLE PHASE 1 KVA
A Laboratory Type Model For Conducting Various Experiments.
TECHNICAL SPECIFICATION :
Transformer Single Phase Air cooled capacity 1KVA, Primary 230 Volts,
Secondary 0-110-115-120 Volts.
The unit must be fitted in MS Box with side ventilation. Top of the box will
be of Backelite sheet and the terminals of primary & secondary will be
brought out with Educational type backelite banana type terminals and
proper marking.
Three phase transformer, shell type oil cooled
TECHNICAL SPECIFICATIONS
1) Capacity 3 phase, 5 KVA, 440 / 230 Volts, 50 Hz
2) Delta - star connection
3) Shell type - Oil cooled (Oil should be supplied by the supplier)
4) Totally enclosed, maximum ambient temp 45° C
5) Insulation Class 'B'
6) Tapping on Secondary Side 50% and 86.6%
7) Educational type Backelite insulated banana terminals . With
colour code provided on the top ofthe transformer and on 6mm
backelite sheet
8) The tank will be provided oil filling Hole with cap, oil level
indicator, drain plug and earthing terminal
9) Plain unidirectional Roller will be fitted to the tank for movement
Oscilloscope Dual Trace,30 MHZ
Features :
DC ~ 30MHz
Inbuilt 6 Digit seven segment display frequency counter (30MHz)Dual
channel, X Y mode
6" display cathode ray tube, sensitivity triggering up to 1mV/divison
TV synchronous separation circuit to observe stable TV signal
Polarity reversal, CH 1Sync output
Technical Specifications :
CRT
: 6” Rectangular screen with internal graticule,
8 x 10 Div (1Div=1cm)
Vertical Deflection
Vertical Operation Mode: CH1, CH2, ADD, ALT, CHOP (CH1, CH2)
Sensitivity
: 5mV/div to 5V/div +3%,
1mV/div to 1V/div +5% (x5),10 steps
Rise time
: <17.2ns
Input impedance : 1Mohm
Max. Input voltage: 250V (DC+AC peak value) at 1kHz
(250V, DC+AC)
Input coupling
: AC, DC, GND
Polarity selection : +(CH2 only)
Display mode
: 1, 10, X-Y
Horizontal Deflection
Sweep time
: 0.2micros/div to 0.2s/div
Sweep expansion
: x10
Accuracy
: 3%
1 No.
1 No.
1 No.
30
Trigger System
Triggering mode : Auto, NORM, TV-V, TV-H
Trigger source
: VERT,CH1, LINE, EXT
Sensitivity auto : 20Hz~20MHz(VERT) (Model ME 3020F)
Frequency norm : 0.5div INT, 0.5Vp-p EXT
TV-H
: At least 1div or 1Vp-p
Input impedance : 1M ohm
X-Y Phase Difference
: <3O, DC-50KHz
Calibration waveform
: Frequency: 1kHz 20%, Voltage: 0.5V 1%
Power requirement
: 220 VAC +10% , 50 Hz
Weight : 8.0Kg Approx.
Dimensions (mm) : 310 (L) x370(B) x 130(H)
Standard Accessories :
Power cable, Probe - 2Nos., Instruction manual
Function Generator
Technical Specifications :
Frequency range:0.1Hz ~ 5MHz
Output waveform : Sine, Triangle, Square, Positive & Negative Pulse,
Positive & Negative Ramp
Output impedance : 50ohms + 10%
Amplitude
: Not less than 20V p-p (open circuit)
DC voltage
: 0~+10V continuously adjustable
Symmetry range: 90:10 – 10:90
Attenuation
:20dB, 40dB, 60dB
Rising edge of square: <100ns
Sine characteristics:<1% at 10Hz ~ 100KHzdistortion
Frequency response: 0.1Hz ~ 100kHz :< ± 0.5dB
: 100kHz ~ 5MHz :<± 1dB TTL/CMOS Output level:TTL
low level <0.4V in pulse wave, High level
<3.5V. CMOS low <0.5V in pulse wave, high
level 5V~14V continuously Variable
Rising time
:< 100ns
VCF Input
Output voltage : -5V ~ 0V ± 10%
Max. Volt-controlled : 1000:1
Input signal
: DC ~ 1kHz
1 No.
Frequency Counter
Measuring range : 1Hz ~ 30MHz
Input impedance : Not less than 1Mohms/ 20pF
Sensitivity
: 100mV rms
Max. Input
: 150V (AC + DC)
Input attenuation: 20dB
Accuracy
: Less than 0.003% ± 1digit
Power requirement: 220 VAC +10% , 50 Hz
Weight
: 3.0Kg Approx.
Dimensions (mm): 220(L) x 270(B) x 185(H)
Standard Accessories :
Power cable, BNC to Crocodile Clip Probes - 1No & BNC to BNC Probe
- 1No., Instruction manual
31
Discrete Component Trainer
Technical Specifications :
Inbuilt Variable / Fixed DC Regulated Power Supplies
Output voltages : 0-3VDC : 0-30VDC
: +5VDC
Inbuilt AC Power Supplies
Output voltages : 10 - 0 - 10VAC/ 500mA
Glass Epoxt PCB used as front panel of 270 mm x 170 mm & mounted on
light weight shock proof plastic cabinet
Symbol diagram printed on Glass Epoxt PCB & all important test Points
are
brought out on front panel
Power requirement: 230 VAC 10%, 50Hz.
Weight : 2.2 Kg Approx.
Dimensions (mm) : 300( L) x 175(B) x 75(H)
List of Experiments under above Topics :
PN Junction Diode V-I Characteristics
Zener Diode V-I Characteristics
Voltage Stabilization of Zener Diode
LED Characteristics
Resistance in Series & Parallel
1 No.
Charging & Dischrging of Condensor
LCR Resosnace Circuit
Clipping & Clamping
Half Wave, Full Wave & Bridge Rectifier
Common Base Transistor Amplifier
Common Emitter Transistor Amplifier
Common Collector Transistor Amplifier
RC Coupled Amplifier
Basic Logic Gates
RC Passive Filter Circuits
PROVIDED with Easy log pro software and computer interface unit to
show reading and graph between Voltage and Current .
Standard Accessories :
Power cable, Patch Chord & Instruction manual
32
33
34
Linear I.C.Trainer
Technical Specifications :
Inbuilt Variable / Fixed DC Regulated Power Supplies
Output voltages : 0-2.5VDC ( 2 Nos.)
: +15VDC
: -15VDC
: +5VDC.
On Board Digital Panel Meter
Voltmeter
: 0-2VDC / 0-20VDC ( Duel Range )
Glass Epoxt PCB used as front panel of 270 mm x 170mm & mounted on
light weight shock proof plastic cabinet
Symbol diagram printed on Glass Epoxy PCB & all important test Points
areBrought out on front panel
Power requirement
: 230 VAC 10%, 50Hz.
Weight : 2.3 Kg Approx.
Dimensions (mm) : 300( L) x 175(B) x 75(H)
Digital I.C.Trainer
Technical Specifications :
Inbuilt Fixed DC Regulated Power Supplies
Output voltages : + 5VDC
On Board Inputs, Switch, Indicators & Clock
Logic Inputs
: 8 Nos. logic '0' & logic '1' ( Through SPDT Switches )
Output indicators : 8 Nos.
Clock
: 1Hz, 100Hz, 1KHz
Gates & Flip Flops
NAND Gates
: 4Nos.
NOR Gates
: 4 Nos.
OR Gates
: 4 Nos.
AND Gates
: 4 Nos.
EX-OR Gates
: 4 Nos.
NOT Gates
: 6 Nos.
JK Flip Flop
: 2 Nos.
RS Flip Flop
: 1 No.
D Flip Flop
: 1 No.
Glass Epoxt PCB used as front panel of 400 mm x 225 mm & mounted on
light weight shock proof plastic cabinet
Symbol diagram printed on Glass Epoxt PCB & all important test Points
are Brought out on front panel
Power requirement
: 230 VAC 10%, 50Hz.
Weight : 1.7Kg Approx.
Dimensions (mm) : 430( L) x 230(B) x 90(H)
Standard Accessories :
Power cable, Patch Chord & Instruction manual
Oil Testing Kit 60 KVA
1 No.
1 No.
1 No.
CTS Third Semester: Electrician
SHOP TOOLS, INSTRUMENTS and MACHINERY
1
Hygrometer
Range
0 to 100% rH
Resolution
0 to 100% rH
Accuracy
±2% ±1 digit
Sensor/Input
Capacitive
Attributes:Humidity measuring and control instrument for
refrigeration, food, laboratory, paper, construction and
other industry. 0-10 V and 0-20 mA output option.
Special Features
·
Housed in box
·
96 x 48 x 110 mm DIN size
·
Calibration Certificate
2
A)
B)
C)
RelaysCut Out Relay
Objective:
·To study the construction of relay
·Test an relay in instantaneous Cut Out protection scheme for operating
characteristic using current injection
Technical Specifications:
·Relay Type
: Instantaneous Cut Out Relay
(Electromechanical)
·Terminals
: 4mm Terminals for Trip, Current Output
and Input
·Meters (Graphical LCD Display): 1No. AC Current Meter 0 – 20Amps
& 1 No. Digital Timer .0001sec. to 9999sec. (Auto) (96mm x 48 mm)
·Current Injector : Inbuilt variable current injector Amps 20Amps to
create Phantom Fault Current
·Indicators
: Provided on front panel for Mains, Current,
Trip and Alarm
·Switches
: Provided on front panel for Mains, Timer
Reset, Test Switch (ON/OFF)
·Relay Circuit Diagram
: Screen Printed on front panel size 700mm
x 400mm
·Dimensions
: 700mm x 400mm x 300mm
·Weight
: 30Kgs Approx.
·Power Requirement
: 220VAC +10%, 50Hz
Standard Accessories:
·
Power Cords, Patch Cords, Instruction Manual
Reverse Current Relay
The Experimental Setup consists of the following parts:
Two nos. of Reverse Power Relay provided on the Front Panel.
Two Nos. of Digital Current meter (0-20A) of size 96X 48 mm provided
on the Front Panel.
Two Nos. of Digital Timer of size 96X 48 mm provided on the Front
Panel
All Meters should be (Graphical LCD Display)
Circuit Diagram printed on front panel With Instruments Connecting
lamp i.e TRIP, CURRENT & ALARM.
Dimension (mm): 900X600.
Power Requirement : Single Phase 230V/50Hz .
.
Over Current relay
Objective:
·To study the operating characteristics of relay
·To study the time – current characteristics of the given fuse
Technical Specifications:
·Relay Type
: Thermal Over Load Relay
·Terminals
: 4mm Terminals for Trip, Current Output
and Input
·All Meters should be (Graphical LCD Display): 1No. AC Current Meter
1 set
1 No. each
D)
3
4
0 – 20Amps & 1 No. Digital Timer .0001sec. to 9999sec.
(Auto) (96mm x 48 mm)
·Current Injector : Inbuilt variable current injector 20Amps to create
Phantom Fault Current
·Indicators
: Provided on front panel for Mains, Current,
Trip and Alarm
·Switches
: Provided on front panel for Mains, Timer
Reset, Test Switch (ON/OFF)
·Relay Circuit Diagram
: Screen Printed on front panel size 700mm
x 400mm
·Dimensions
: 700mm x 400mm x 300mm
·Weight
: 30Kgs Approx.
·Power Requirement
: 220VAC +10%, 50Hz
Standard Accessories:
·Power Cords, Patch Cords, Instruction Manual.
Under Voltage Relays
Objective:
·To study the construction of relay
·Test an relay in over / under voltage protection scheme for operating
characteristic using voltage injection
·To obtain the time & current characteristics of a over / under voltage
type relay (Static)
Technical Specifications:
·Relay Type
: Over / Under Voltage Relay (Static Type)
·Terminals
: 4mm Terminals for Trip, Voltage Output
and Input
·All Meters should be (Graphical LCD Display) : 1No. AC Voltmeter
Meter 0 – 220V & 1 No. Digital Timer . 0001sec. to 9999sec. (Auto)
(96mm x 48 mm)
·Voltage Injector : Inbuilt variable voltage injector 220V to create Fault
Voltage
·Indicators
: Provided on front panel for Mains, Voltage, Trip and
Alarm
·Switches
: Provided on front panel for Mains, Timer Reset,
Test Switch (ON/OFF)
·Relay Circuit Diagram
: Screen Printed on front panel size 700mm
x 400mm
·Dimensions
: 700mm x 400mm x 300mm
·Weight
: 30Kgs Approx.
·Power Requirement
: 220VAC +10%, 50Hz
Standard Accessories:
·Power Cords, Patch Cords, Instruction Manual
Starters for 2 to 5 H.P. A.C Motorsa. Resistance type starter
b. Direct on line Starter
c. Star Delta Starter- manual,
semi-automatic
automatic
d. Auto Transformer type
Motor Generator(DC to AC) set consisting of A Laboratory Type Model for Conducting Various Experiments.
Technical Specification :
MOTOR
5 H.P., 440 volts, 1500 R.P.M., S.P.D.P. type continuous rating class of
insulation 'F'. Horizontal foot mounted, Dynamically balanced. All the
terminals are brought out to terminal box. Confirming to provided lifting
bolt & earthling terminal.
ALTERNATOR :
3.5 K.V.A.,415/240 Volts, 50 H.Z., 3 phase 4 wires 0.8 P.F.1500
R.P.M., S.P.D.P. type continuous rating with self static field exciter, self
regulation, insulation class 'H' frame , Horizontal foot mounting
confirming to Alternator is provided lifting bolt & earthling terminal.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel
and MS sheet of 1 mm thickness, Siemens Grey colour powder coated
with wooden top on the working area.
1 No.
1 No.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W
= 900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick
bakelite sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
of 750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm
teakwood lipping patti.
. Educational type backelite insulated banana terminals provided for
supply and motor gen.Connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
D.C. SIDE
1)Voltmeter M.C, Type 0-500 volts,96 x 96mm : 1 no.
2) Ammeter M.C.Type 0-15 Amp.96 x 96 mm Make Make : 1
no.
3) Field regulator disc type 500 ohm,1.5 Amp. : 1 no.
4) Indicating lamp LED type Red, colour 12mm size. :1 no.
5) D.P.S.T. 20 Amp Knife Switch : 1 no.
6) Three Point D.C. Motor Starter Sutaible : 1 No.
A.C. SIDE
1)Voltmeter M.I, Type 0-500 volts,96 x 96 mm Make Make
: 1 no.
2) Ammeter M.I.Type 0-15 Amp.96 x 96 mm Make Make
: 1 no.
3) Ammeter M.C.Type 0-1.5 Amp.96 x 96 mm Make Make
: 1 no.
4) Frequency meter 45-50-55 Hz. 96 x 96 mm Make Make
: 1 no.
5) Rotory Switch for voltmeter select for OFF/RY/YB/BR 16 Amp.,440 v
: 1 no.
6) Indicating lamp LED type R.Y.B.colour, 12mm size : 1 each
7) Field regulator disc type suitable to decrease field current up to
min.Amps : 1 no.
8) Field control separately excited unit suitable for above alternator
should be mounted inside the panel board
9) Ammeter Selector Switch, Rotory type, Off/R/Y/B, 16 A. 440 V.
: 1 no.
10) 3 ph. Power Factor Meter, 5 Amp.,440V, 96x96mm
: 1 no.
All meters 96 x 96 mm size pannel mounted type maximum in
accuracy.
5
A.C. SQUIRREL CAGE INDUCTION MOTOR 3 HP WITH STAR
DELTA STARTER
A laboratory type model for conducting various experiments.
TECHNICAL SPECIFICATION :
Motor
A.C. 3 Phase 3 HP 415 volts, 50 Hz, Squirrel cage Induction Motor
1440 RPM, TEFC, class 'F' insulation, frame 100, horizontal foot
mounted. Six terminals brought out on terminal box.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel
and MS sheet of 1 mm thickness, Siemens Grey
colour
powder
coated with wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W
= 900 mm ; D = 250 mm ; H = 750 mm & Front
side
of 6mm
thick bakelite sheet of brown colour and fitted at inside of the tube
structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
1 No.
6
7
of 750 mm from bottom.
The top of W
= 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :1) Voltmeter
M.I. Type 96 mm x 96 mm Sq. 0-500V with selector switch
Off/RY/YB/BR : 1 No.
2) Ammeter M.I. type 96 mm x 96 mm Sq. 0-10A : 1 No.
3) Suitable star delta. Starter : 1 No.
4) TP MCB 16 Amp 415 V. ISI Marked mounted on panel board. : 1 No.
5) Indicating lamp LED type 12 mm size for incoming & outgoing in
colour code : 6 Nos.
6) HRC fuses Bakelite type base with top 16 Amp 440 V
: 3 Nos.
PAINT :
Motor will be painted with two coats of smoke gray oil paint and panel
board will be powder coated.
BASE PLATE :
Motor mounted on fabricated base plate of M.S.'C' channel size 75 x 40
x 6mm thick .
Motor AC phase wound slip ring type 5 HP 400 volts, 30phase, 50
cycles with starter and switch.
Technical Specification :
Motor :
A.C. 3 Phase 5 HP 415 volts, 50 Hz, slip ring Induction Motor 1440
RPM, TEFC, class 'B' insulation, frame 100, horizontal foot mounted.
Educational type Bakelite banana type terminals 30 Amps is provided
on terminal box. Six terminals are brought out on terminal box. Rugged
construction.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular
mild
steel and MS sheet of 1 mm thickness, Siemens Grey colour powder
coated with wooden top on the working area. The overall dimensions W
= 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm
thick
bakelite sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel is perforated
for air ventilation. Back side in the form of hinged door with suitable
locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
of 750 mm from bottom. The top of W = 900 mm x D = 375mm and
made of 19mm marine plywood fitted with 3 mm Ivory coloured sheet
on top. The three sides of the working top lipped using 22mm x 6mm
teakwood lipping patti.
Educational type backelite insulated banana terminals provided for
supply and motor connection.Circuit diagram of panel provided inside
the panel. All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
(1)Voltmeter M.I. Type 96 mm x 96 mm Sq. 0-500V with: 1No.selector
switch Off/RY/YB/BR
(2) Ammeter M.I. type 96 mm x 96 mm Sq. 0-20A: 1 No.
(3) Suitable Rotor Resistance starter : 1 No.
(4) TP MCB 16 Amp 415 V. ISI Marked is mounted on panel board
-1No.
(5) Indicating lamp LED type 12 mm size for incoming & outgoing in
colour code- 6Nos.
(6) HRC fuses Backelite type base with top 16 Amp 440 V -3Nos
PAINT :
Motor is painted with two coats of smoke gray oil paint and panel board
is powder coated.
Motor A.C. series type 230V, 50 cycles 1/4 HP with mechanical
load
Technical Specification :
AC Series Type Motor 230V, 50 cycles 1/4 HP with Mechanical Load,
with
Control Desk :
1 No.
1 No.
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular
mild
steel and MS sheet of 1 mm thickness, Siemens Grey colour powder
coated with wooden top on the working area. The overall dimensions W
= 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm
thick
bakelite sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel is perforated
for air ventilation. Back side in the form of hinged door with suitable
locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
of 750 mm from bottom. The top of W = 900 mm x D = 375mm and
made of 19mm marine plywood fitted with 3 mm Ivory coloured sheet
on top. The three sides of the working top lipped using 22mm x 6mm
teakwood lipping patti.
Educational type backelite insulated banana terminals provided for
supply and motor connection.Circuit diagram of panel provided inside
the panel. All accessories connected with internal wiring ferrules etc.
8
Control Panel provided Starter Switch, MCB, Voltmeter, Ammeter,
Frequency Meter and Terminals provided for Measurement and Easy
Input and Output Connections. Panel fitted on good quality Wooden
Box (for Safety), and Tapered Shape for better view Angle. Supplied
with required Connection Leads and Instruction Manual.
Motor A C single phase 230 volt, 50 cycles 1 HP capacitor type
with starter switch 1 HP
A laboratory type model for conducting various experiments.
TECHNICAL SPECIFICATION :
MOTOR :
A.C. Single Phase Capacitor Start Induction Motor 1 HP 230 volts AC,
50 Hz, 1440 RPM, TEFC, class 'B' insulation, frame 90, horizontal foot
mounted.
Educational type Backelite banana type terminals 30 Amps provided on
terminal box.
Starting winding, running winding with capacitor terminals brought out
on terminal box
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel
and MS sheet of 1 mm thickness, Siemens Grey
colour
powder
coated with wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick
bakelite sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
of 750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivorycolour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided
for supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
1) Voltmeter M.I. Type 96 mm x 96 mm Sq. 0-300V : 1 No.
2) Ammeter M.I. type 96 mm x 96 mm Sq. 0-10A : 1 No.
3) Suitable D.O.L. Starter Single Phase : 1 No.
4) DP MCB 16 Amp 250 V. ISI Marked mounted on panel board :1 No.
5) Indicating lamp for incoming &outgoing , LED type, 12 mm size : 2
Nos.
6) HRC fuses 16 Amp Backelite type base : 2 Nos.
PAINT :
Motor will be painted with two coats of smoke gray oil paint and panel
board will be powder coated.
BASE PLATE :
1 No.
9
Motor mounted on fabricated base plate of M.S.'C' channel size 75 x 40
x 6mm thick
Motor universal 230 volt, 50cycles 1/4 HP with starter/switch
A Laboratory Type Model For Conducting Various Experiments.
TECHNICAL SPECIFICATION :
MOTOR :
Universal Motor Single Phase, Capacity 750 Watts, 230 volts A.C. /
D.C. 1500 RPM (O.L.) 50 Hz, TEFC, class 'B' insulation, frame 100,
horizontal foot mounted. Educational type Backelite Insulated banana
type terminals 30 Amps provided on terminal box.
Four terminals armature and field brought out on terminal box with
marking.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel
and MS sheet of 1 mm thickness, Siemens Grey
colour
powder
coated with wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W
= 900 mm ; D = 250 mm ; H = 750 mm & Front
side
of 6mm
thick bakelite sheet of brown colour and fitted at inside of the tube
structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height
of 750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm
teakwood lipping patti.
1 No.
Educational type backelite insulated banana terminals provided for
supply and motor connection Circuit diagram of panel provided inside
the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories :
Voltmeter M.I. type 96 mm x 96 mm Sq. 0-300V : 1 No.
Ammeter M.I. Type 96 mm x 96 mm Sq. 0-5A : 1 No.
Suitable D.O.L. Starter : 1 No.
DP MCB 16 Amp 230 V mounted on panel board : 1 No.
Indicating lamp for incoming & outgoing, LED type, 12 mm size : 2 Nos.
HRC fuses 10 Amp, 230 V Backelite type base : 2 Nos.
Change over switch for AC and DC output : 1 No.
Suitable Stand by DC Supply provided inside the panel. : 1 No.
PAINT :
Motor will be painted with two coats of smoke gray oil paint and panel
board will be powder coated.
BASE PLATE :
Motor mounted on fabricated base plate of M.S.'C' channel size 75 x
40 x 6mm thick
10
11
12
13
Stepper Motor with Digital Controller
Microprocessor based stepper motor controller : with a bifilar 2 phase
D.C. stepping motor.
The stepping motor can be programmed in three parameters namely
1. Speed 2. No. of steps. 3. Direction.
It is specially designed low cost yet sophisticated control lab kit the
microprocessor system consist of 8085 A CPU 8155 scratch pad and
8279 key board display controller and EPROM The monitor programme
in EPROM is used to enter application progra-mme forstepper motor
controller.
The unit which houses the stepper motor is designed to demonstrate
the basic principles of stepper motor with manual switching. The same
contains power amplifiers and Regulated power supply with Stepper
motor Power amplifier alongwith regulated power driving the stepper
motor.
Arrangement for manual operation of stepper motor control.
Shaded Pole Motor
Bath Impregnating
Oven Stove, Sixe 300mmx300mmx300mm
1 No.
1 No.
1 No.
1 No.
TOOLS AND EQUIPMENT NEEDED ADDDITIONAL TO EXISTING TOOLS LIST
1
2
Synchronous motor 3 Phase, 3 HP, 415V, 50Hz, 4 Pole, with
accessories.
TECHNICAL SPECIFICATION :
MOTOR:
Synchronous motor 3 Phase, 3 HP, 415V, 50Hz, 4 Pole,
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel
and MS sheet of 1 mm thickness, Siemens Grey
colour powder
coated with wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size
W = 900 mm ; D = 250 mm ; H = 750 mm & Front
side of 6mm
thick bakelite sheet of brown colour and fitted at inside of the tube
structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking
arrangement.
The working area top fitted in front of the Instrument Panel at a
height of 750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivory colour sheet on top.
The three sides of the working top lipped using 22mm x 6mm
teakwood lipping patti.
Educational type backelite insulated banana terminals provided for
supply and motor connection Circuit diagram of panel provided
inside the panel.
All accessories connected with internal wiring ferrules etc.
The Instrument Panel consist of following accessories
1. Three Nos. of Moving Coil Ammeter of Range 10A AC of size
96*96mm provided on the Panel.
2. Three Nos. of Moving Coil Ammeter of Range 3A AC of size
96*96mm provided on the Panel.
3. One No. of Moving Coil Ammeter of Range 3A DC of size
96*96mm provided on the Panel.
4. Two Nos. of Moving Coil Voltmeter of Range 500V AC of size
96*96mm provided on the Panel.
5. One No. of Frequency Meter of Range 50/55Hz of size 96*96mm
provided on the Panel.
6. Two Nos. of Miniature Circuit Breaker of Range 16Amps (MCB/
TPN) Provided on the Input Side &
Output Side.
7. One No. of Variable Rheostat of Range 250 Ohms/ 200 Watts
Provided behind the Front Panel with
SPST Switch.
8. One No. of Direct On Line Starter of Range 7HP/ 10Amps
Provided on the Front Panel.
9. One No. of Starter Switch of Range 9 - 14Amps. Provided On the
Front Panel.
10. Six Nos. of Indicators provided on the Input & Output side.
11. Dimensions : 775 x 360 x 560 mm (L x B x H).
12. Power Requirement : Three Phase 415V AC
Lux meter Measurment of Light intensity of UV
1 no.
1 no.
.
CTS Fourth Semester: Electrician
SHOP TOOLS, INSTRUMENTS and MACHINERY
1
2
3
4
Inverter- 1 KVA with 12 V Battery
Input- 12 volt DC,
Output- 220 volt AC
Domestic Appliances –
a. Electric Hot Plate
1500 watt
b. Electric Kettle, 100 watts
c. Electric Iron 1200 watts
d. Immersion Heater 500/100/2000 watt
e. A.C. Fan
f. Geyser (Storage type) 15 ltr minimum
g. Mixture & Grinder
Thyristor/IGBT controlled D.C. motor drive with tacho-generator
feedback arrangement.
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivorycolour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
Digital RPM meter suitable for operation upto 3000 RPM
Other Accessories ON / OFF Rotory Switch, '16 Amp, 250 V , Digital
Ammeter, Digital Voltmeter, Pot, switches, Indication for Digital input
Motor : DC Motor rating 1 HP, 220 V. 4 Amp, 2 Pole.
Thyristor/IGBT controlled A.C. motor drive with VVVF control
3 Phase, 3 HP
Control Desk :
The Control desk consist of an Instrument panel and working area.
The control desk made of 30mm x 30mm x 1.6mm tubular mild steel and
MS sheet of 1 mm thickness, Siemens Grey colour powder coated with
wooden top on the working area.
The overall dimensions W = 900 mm ; D = 625 mm ; H = 1500 mm.
The Box type Instrument Panel above the working area and of size W =
900 mm ; D = 250 mm ; H = 750 mm & Front side of 6mm thick bakelite
sheet of brown colour and fitted at inside of the tube structure.
All other sides made of MS sheet, Two sides of the panel are to be
perforated for air ventilation.
Back side in the form of hinged door with suitable locking arrangement.
The working area top fitted in front of the Instrument Panel at a height of
750 mm from bottom.
The top of W = 900 mm x D = 375mm and made of 19mm marine
plywood fitted with 3 mm Ivorycolour sheet on top.
The three sides of the working top lipped using 22mm x 6mm teakwood
lipping patti.
30 A. Educational type backelite insulated banana terminals provided for
supply and motor connection.
Circuit diagram of panel provided inside the panel.
All accessories connected with internal wiring ferrules etc.
Meters
96X96mm
:1No. Digital Voltmeter Range 0-300V AC , Size
1 No.
1 No. each
1 No.
1 No.
:1Nos. Digital Ammeter Range 0-10A AC , Size
96X96mm
:1No. Digital RPM Meter ,Size 96X96mm
IGBT
: Thyristor/IGBT AC Drive
Protections
:Triple pole & neutral isolator (TPN/MCB) 16Amps
Power requirement:415~440V AC , 50Hz, 3 Phase
Accessories:
AC Induction Motor 3 Phase 3HP with Sensor Arrangement
Technical Specifications (Induction Motor):
Capacity
:3HP
Cage
:Steel Body
Class
: E Class
RPM
: 1500 approx.
Shaft
:Single
Current
:6 Amps Max.
Windings
:Stator winding
Input Terminal
:6
Mounting
:Foot Mounted arrangement
Power requirement:415~440V AC , 50Hz, 3 Phase
TOOLS AND EQUIPMENT NEEDED ADDDITIONAL TO EXISTING
TOOLS LIST
1
2
3
4
5
Pentium IV Computer or latest (Server- Linux), 2.8 GHz &
above, 1 GB RAM, 80 GB HDD, DVD Combo Drive, 15/17”
Monitor, optical scroll mouse, multimedia key board, 32 bit
LAN card with UPP port, necessary Drivers, etc.
Ink jet/ laser printer
Washing Machine
Motor Pump set 1 HP, 1 Phase, 240 V
Pin Type, shackle type & suspension type insulators (Raw
Material)
2 Nos.
1 No.
1 No.
1 No.
2 Nos.
each
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement