CX-Vehicle Power Charger
CX-Vehicle Power Charger
DESIGNED FOR MOBILE APPLICATIONS
KEY FEATURES
 Universal voltage with unity
power factor correction
 12V and 24V ranges
 Output current 15-80A
 High efficiency/cool running
 Small and easy to install
The CX-Vehicle Power Charger is our fourth
generation of charging system and has been
designed from outset by our partners to
provide a fully featured power supply to
 Microprocessor with user
configurable regimes for GEL,
AGM, Flooded and lithium.
 Fully automatic 4 stage charge
cycle control
directly integrate into your vehicle — whatever
 Vibration tested to 2G
the load.
 Starter battery charging (ESB)
 Sleep mode option
Power charging is the ability to simultaneously
 Rescue battery mode
act as a battery charger and power supply to
 Remote temperature/voltage
power any connected loads without gassing
the battery. Thus providing opportunity
charging, long term charging and the safe
sensor and controller options
 Applications and in-service
support from a UK company
and reliable operation of electrical on-board
Intelligent Charging
equipment.
Unlike basic chargers, the CX-VPC
uses an optimum four stage charging
regime which safely refills the battery
in the quickest time possible - thereby
improving the life of the battery. It
makes it suitable for both overnight
and opportunity charging.
The CX-V Power Charger is extremely
powerful and compact , making it ideal for
on-board use.
Antares TDC
Knaves Beech Business Centre
Davies Way
Loudwater
HIGH WYCOMBE
HP10 9QR UK
80A output from such a small package is
www.antares.co.uk
email: [email protected]
tel: +44 (0)1628 535440
fax: +44 (0)1628 535441
Charging regimes are selectable for GEL,
achieved through high efficiency using the
very latest electronic components.
AGM, Flooded and Li Ion (special option)
Remote control and remote battery
temperature/voltage sensing completes this
comprehensive solution to vehicle power
After switch-on, or after the battery
voltage dips, the charger will operate
at its maximum rating, bulk charging
the battery as fast as possible.
The CX-VPC is programmed to
continue bulk charging until it reaches
a higher voltage -“forcing” charge into
the battery. Accurate sensing avoids
the charger reaching the ‘gassing’
point and it safely switches to a second
stage bulk charge, and finally to a
taper charge. There is a fourth
periodic equalisation charge if
CX-Vehicle Power Charger
DESIGNED FOR MOBILE APPLICATIONS
required. This charging process
dramatically reduces the time taken
to get to full charge.
warm conditions. Alternatively the
charger can be configured as a
constant voltage power supply
The charger is temperature
compensated, adjusting its output
to ensure that when the batteries
are cold the voltage is raised and
when warm the voltage is reduced.
This ensures charging in cold
weather and avoids gassing in
Remote Voltage/Temp
Sensor
High Specification
The charger is equipped with
many of the protection features
not found in other chargers and
offers the professional
specifier ,vehicle builder and fleet
user a robust proven solution that
they can use with confidence.
A remote sensor is available
where the battery is located in a
different climatic environment or
long charging cables are
needed.
12V
Part Number
Output Current
No of main outputs +
Engine Start battery ESB
96637
96638
96639
96640
96641
96642
96643
96644
15A
25A
35A
50A
80A
15A
25A
40A
1 +ESB
2 + ESB
2+ESB
3
3
2
3
3
Float/Boost Voltage
Output Power (nominal)
180W
Select Float 13.8/13.5/
Select Float 27.6/27.0
Or boost 14.4 /14.7VDC
Or boost 28.8/29.4VDC
300W
Typical efficiency
420W
600W
960W
360W
87%
Input voltage
Dimensions (mm)
24V
600W
960W
90%
90V-264V (47-63Hz)
213 x
213 x
273 x 77 312 x 77
(H )
(H )
183 x 244 x 72(H )
Weight (Kg)
1.6kg
Features
Alarm signal, Quiet fan off Sleep Mode, Remote control, Engine start battery ESB output
@ 13.8V/2A on (15/25/35A) units only
Vibration
10-500Hz, 2G 10min / 1 cycle period for 60 min, X Y Z axes
Charging regimes
Temperature ranges
Protection
Connections
Options
Safety Standards
EMI conduction/radiation
EMI Immunity
1.7kg
1.9kg
3.1kg
4.0kg
183 x
213 x 273 213 x 312
244 x 72
x 77(H )
x 77(H )
(H )
1.6kg
2.9kg
3.9kg
Lead Acid (Flooded, AGM, GEL) & Lithium Ion (special version)
Operating -20˚C to +50˚C Storage –40˚C to +75˚C
Temperature controlled cooling fan, short circuit, reverse polarity, overvoltage (recovery
after reset AC power on), over temperature (auto recovery)
AC connection IEC appliance socket,
DC connections screw terminals, control via RG45 socket
(1) Remote display on/off control and indication Pn 91067
(2) Remote battery temperature compensation and over temperature detection Pn 96645
Certified EN60355-1 EN 60335-2-29
EN55022; EN55024; EN 61204-3: EN 55014-1; EN 55014-2
IEC 61000-4-2, 3, 4, 5, 6, 8,11;ENV 50204
Due to our policy of continuous product development, specifications are subject to change without notice
PUB182/1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement