AII25749 2 Door XM Radio System.pmd
INSTALLATION
INSTRUCTIONS
Accessory
Application
XM RADIO SYSTEM
2004 ACCORD 2-DOOR
(LX/EX L4, LX V6)
Publications No.
AII 25749
PARTS LIST
Issue Date
FEB 2004
Double-sided adhesive tape
XM Radio Attachment Kit (sold separately):
P/N 08B15-SDN-100
DIN cable
Display unit pocket
Clip nut
XM radio harness
3 Self-tapping screws
Fastener
Upper bracket
Ground bolt (gold)
Lower bracket
6 Washer-screws, 4 x 8 mm
2 Washer-bolts, 6 x 12 mm
Modulator bracket
4 Flange nuts, 4 mm
2 Washer-screws, 5 x 10 mm
30 Wire ties
2 Flange nuts, 5 mm
Connector clip
3 Off-set wire ties with clip
8 Wire tie with clips (two not used)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
08B15-SDA-1001-91
1 of 22
5 Cushion tapes
Audio Attachment Kit (sold separately):
P/N 08B06-SDA-100
(Not required if already equipped with a player.)
5 EPT sealers
Left player bracket
Fuse label
Mini fuse, 5A
Right player bracket
Antenna Kit (sold separately):
P/N 08A15-1E1-100
Left player subbracket
Antenna cable
Right player subbracket
Base Kit (sold separately):
P/N 08A15-1E1- 000
Player base-bracket
Display unit
FM modulator unit
Player panel
Receiver unit
Pocket
Owner's Manual
2 of 22
BUS cable
(Used on vehicles without
Navigation)
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
2 Latches
Illustration of the XM Radio System Installed in the
Vehicle
8 Flange nuts, 6 mm
DISPLAY MODULE
RECEIVER
UNIT
ANTENNA
DIN CABLE
2 Grommet screws
2 Wire ties
2N28160M
FM MODULATOR
UNIT
3 EPT sealers
XM RADIO
HARNESS
VEHICLE
ANTENNA
CABLE
DISPLAY
MODULE
2 Self-tapping screws, 4 x 12 mm
TOOL AND SUPPLIES REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Flat-tip screwdriver
Isopropyl alcohol
Shop towel
Tape measure
Utility knife
Hook tool
Ratchet wrench
8 mm and 10 mm Sockets
Felt-tip pen
Scissors
Push pin
Vinyl tape
Drill
3 mm and 10 mm Drill bits
Touch-up paint
Eye protection (face shield, safety goggles, etc.)
Masking tape
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
FM MODULATOR
UNIT
DIN CABLE
RECEIVER UNIT
FUSE BOX
6-PIN
CONNECTOR
XM RADIO
HARNESS
ANTENNA
2N28010M
AII 25749 (0402)
3 of 22
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the radio station presets.
2.
Disconnect the negative cable from the battery.
3.
Remove the trim ring.
•
Gently pry up on the trim ring to release the six
clips.
•
Unplug the two seat heater connectors
(if equipped), and remove the trim ring.
RETAINING
CLIPS (4)
RETAINING
CLIPS (2)
M/T Vehicle:
•
Squeeze the plastic clip, and pull down on the
shift boot. Remove the shift knob by turning it
counterclockwise.
TRIM
RING
SHIFT KNOB
(Turn counterclockwise.)
SEAT HEATER
CONNECTOR
(if equipped)
2206041K
A/T Vehicle:
PLASTIC
CLIP
SHIFT
BOOT
•
Gently pry on the trim ring to release the six
clips.
•
Unplug the two seat heater connectors
(if equipped), and remove the trim ring.
2206032K
RETAINING
CLIPS (4)
RETAINING
CLIPS (2)
TRIM RING
SEAT HEATER
CONNECTOR
(if equipped)
2206112K
4 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
4.
If the vehicle is equipped with a cassette/MP3/CD
player, go to step 13; otherwise, go to step 5.
Remove the center holder.
•
Open the lid, and remove the coin pocket.
•
Remove the two self-tapping screws.
•
Gently pull out the dashboard center holder to
release the two retaining clips, unplug the
vehicle connector, and remove the center
holder.
5.
Remove the pocket:
•
Apply masking tape to the edge of the center
panel.
•
Remove the two self-tapping screws.
•
Push in on the bottom of the lid, then pull out
on the top by inserting the end of a hook tool
between the pocket and center panel. Pull the
pocket toward you to release the two retaining
clips.
•
Set the pocket aside; it will not be reused.
With Coin Pocket:
COIN
POCKET
LID
CENTER HOLDER
SELF-TAPPING
SCREW
MASKING
TAPE
HOOK
TOOL
RETAINING
CLIPS (2)
RETAINING
CLIPS (2)
POCKET
LID
VEHICLE
CONNECTOR
POCKET
With Optional Ashtray:
2206061K
•
Open the lid, and remove the ashtray.
•
Remove the two self-tapping screws.
•
Gently pull out on the two retaining clips,
unplug the cigarette lighter harness connector,
vehicle connector, illumination bulb, and
remove the center holder.
CENTER
HOLDER
SELF-TAPPING
SCREW
6.
ASHTRAY
SELF-TAPPING
SCREW
ILLUMINATION
BULB
2206073K
Remove the right and left inner covers (one hook
and one clip for each cover). Set the inner covers
aside; they will not be reused.
CLIP
LEFT INNER
COVER
RETAINING
CLIPS (2)
RIGHT INNER
COVER
2730010K
VEHICLE
CONNECTOR
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
CIGARETTE
LIGHTER
HARNESS
CONNECTOR
AII 25749 (0402)
POCKET
OPENING
HOOK
2226010K
5 of 22
7.
Remove the vehicle harness clip from the vehicle
frame, and move the clip out of the way.
PLAYER BASEBRACKET
VEHICLE
FRAME
10. Get the pocket from the audio attachment kit.
Using a utility knife, cut the two lugs off of the
pocket.
LUG
(Cut off.)
VEHICLE
HARNESS
CLIP
(Remove.)
6 mm
FLANGE
NUT
POCKET
LUG
VEHICLE
FRAME
6 mm
FLANGE
NUT
11. Install one latch onto the left and right player
brackets. Slide the clip nut onto the display
module pocket flange.
2306011T
VEHICLE HARNESS CLIP
(Insert into the hole of
the player base-bracket.)
LATCH
Insert the studs from the player base-bracket into
the holes in the vehicle frame from the back.
Install the two 6 mm flange nuts while holding the
bracket firmly against the vehicle frame. Insert the
vehicle harness clip (removed in step 7) into the
hole in the player base-bracket.
9.
Insert the studs of the left and right player
subbrackets into the holes in the vehicle frame,
and install one 6 mm flange nut on the end of
each stud while pushing each subbracket upward.
DISPLAY
MODULE
POCKET
SELFTAPPING
SCREW (2)
(supplied
with audio
attachment
kit)
VEHICLE
FRAME
LEFT
PLAYER
BRACKET
SCREW
POSITION
RIGHT PLAYER
SUBBRACKET
6 of 22
2306021T
LATCH
CLIP NUT
6 mm FLANGE NUT
LEFT PLAYER
SUBBRACKET
DISPLAY MODULE
POCKET FLANGE
1 mm
8.
VEHICLE
FRAME
2529041T
POCKET
RIGHT
PLAYER
BRACKET
SELF-TAPPING
SCREWS (3)
(supplied with
XM radio
attachment kit)
2N28071M
BRACKET
HOLE
12 Set the display module pocket on the pocket with
the cut out facing up. Position the left and right
player brackets on the display module pocket and
pocket, and install five self-tapping screws.
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
If the vehicle is not equipped with a cassette/MP3/
CD player, go to step 18; otherwise, go to step 13.
15. Remove the left and right audio brackets (two
washer-screws and one self-tapping screw for
each bracket). Separate the player and pocket.
Set the pocket aside; it will not be reused.
13. Remove the player panel by removing the two
self-tapping screws and two clips.
CLIP
PLAYER PANEL
WASHERSCREW
SELF-TAPPING
SCREW
SELFTAPPING
SCREW
2306141T
14. Remove the player/pocket assembly. Unscrew the
four flange nuts, and pull the assembly out toward
you. Unplug the audio subharness cable
connector.
VEHICLE
CONNECTOR
(without
navigation
system)
VEHICLE CONNECTOR
(with navigation system)
PLAYER
(Cassette/MP3/CD)
POCKET
(Do not reuse.)
SELF-TAPPING
2N28080M
SCREW
DISPLAY
MODULE
POCKET
AUDIO
SUBHARNESS
CONNECTOR
(without
navigation
system)
WASHERSCREW
(supplied
with
Audio
Attachment
kit)
LEFT PLAYER
SUBBRACKET
CLIP NUT
PLAYER
(Cassette/MP3/CD)
WASHERSCREW
(supplied
with Audio
Attachment
kit)
SELFTAPPING
SCREW
LEFT
PLAYER
BRACKET
RIGHT
PLAYER
BRACKET
BRACKET
HOLE
6 mm
FLANGE
NUT
RIGHT
PLAYER
BRACKET
PLAYER BASEBRACKET
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
SCREW
POSITION
RIGHT PLAYER
SUBBRACKET
WASHERSCREW
16. Slide the clip nut (supplied) onto the display
module flange.
AUDIO
SUBHARNESS
CONNECTOR
(with navigation
system)
LEFT PLAYER
BRACKET
RIGHT AUDIO
BRACKET
LEFT AUDIO
BRACKET
DISPLAY
MODULE
SELF-TAPPING
SCREWS (2)
(supplied with
XM radio
attachment kit)
17. Set the player on the display module pocket.
Position the left and right player brackets on the
display module pocket and player, and reinstall the
four washer-screws. Install the three self-tapping
screws to secure the display module pocket.
AII 25749 (0402)
7 of 22
Installing the Display Unit
If the vehicle is not equipped with a cassette/MP3/
CD player, go to step 20; otherwise, go to step 19.
18. Attach the display unit to the display unit pocket:
•
Using isopropyl alcohol on a shop towel, clean
the center on the back of the display unit
where the adhesive backing will attach.
•
Remove the backing from one side of the
double-sided adhesive tape, and attach it to
the display unit.
•
Remove the remaining backing from the
double-sided adhesive tape. Route the display
unit cable through the hole of the display unit
pocket, and attach the display unit to the
display module pocket.
19. Plug the audio subharness cable into the player.
Cassette Player
Make loops in the audio subharness cable, and
secure it with one wire tie, so that the distance
between the ends of the cable connector is
200 mm. Plug the audio subharness cable
connector into the cassette player connector.
CASSETTE
PLAYER
WIRE TIE
(supplied with
audio
attachment kit)
DISPLAY UNIT
AUDIO
SUBHARNESS
CABLE
DOUBLE-SIDED
ADHESIVE TAPE
AUDIO
SUBHARNESS
CABLE
CONNECTOR
Clean with
isopropyl
alcohol.
BACKING
Without Player:
DISPLAY UNIT CABLE
With Player:
AUDIO
SUBHARNESS
CABLE
CONNECTOR
200 mm
2306051T
DISPLAY
UNIT
POCKET
Multimedia Player
Make loops in the audio subharness cable, and
secure it with one wire tie so that the distance
between the ends of the cable connectors is
200 mm. Plug the audio subharness cable
connector into the multimedia player connector.
POCKET
PLAYER
MULTIMEDIA
PLAYER
BUS CABLE
DISPLAY
UNIT
CABLE
DISPLAY
UNIT
POCKET
WIRE TIE
(supplied with
audio
attachment kit)
2N28110M
AUDIO
SUBHARNESS
CABLE
CONNECTOR
AUDIO
SUBHARNESS
CABLE
CONNECTOR
200 mm
2306061T
8 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
In-Dash CD Player
•
•
21. Remove the rear console.
Make loops in the audio subharness cable, and
secure it with one wire tie so that the distance
between the ends of the cable connectors is
180 mm. Plug the audio subharness cable
connector into the connector from the in-dash
CD player.
After connecting, secure the connectors to the
rear of the in-dash player with one wire tie from
the in-dash CD player kit.
IN-DASH CD
PLAYER
AUDIO
SUBHARNESS
CABLE
CONNECTOR
WIRE TIE
(supplied with
audio
attachment
kit)
•
Open the lid, and remove the rear console mat
from inside the rear console.
•
Remove the two screws and the four selftapping screws, and unplug the connector and
harness clip (if equipped).
•
If equipped with a console-mounted CD
changer, remove the changer from the rear
console.
REAR CONSOLE MAT
SELF-TAPPING
SCREWS (4)
SCREWS (2)
WIRE TIE
(supplied with
audio
attachment kit)
AUDIO
SUBHARNESS
CABLE
180 mm
AUDIO
SUBHARNESS
CABLE
CONNECTOR
2306070T
HARNESS CLIP
(if equipped)
CONNECTOR
(if equipped)
2206090K
Routing the XM Radio Harness
20. Remove the beverage holder (pull up to release
the six retaining clips).
RETAINING
CLIPS (2)
RETAINING
CLIPS (4)
BEVERAGE
HOLDER
2206050K
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
9 of 22
22. Remove the driver’s dashboard lower cover:
24. Remove the self-tapping screw and the clip that
secure the left front console cover. Take care not
to damage the clip, and remove the console cover.
•
Remove the self-tapping screw.
•
Release the four clips on the left side first by
pulling out on the driver's dashboard lower cover.
•
After releasing the four clips, insert a flat-tip
screwdriver behind the clip at the dashboard
frame. Gently twist the screwdriver to release
the clip.
•
SELF-TAPPING
SCREW
Release the two clips on the right side. Unplug
the vehicle connector, then remove the lower
cover.
CONNECTOR
CLIP
DASHBOARD
LOWER COVER
LEFT FRONT
CONSOLE COVER
PUSH
SELFTAPPING
SCREW
REMOVE
2206131K
RETAINING
CLIPS (7)
2206120K
23. If equipped, remove the driver’s dashboard under
cover (release the three retaining clips, one pin,
and one holder).
HOLDER
PIN
RETAINING
CLIPS (3)
10 of 22
DRIVER’S DASHBOARD
UNDER COVER
2205020T
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
25. On the driver's side of the vehicle, locate the 6-pin
connector on the fuse box. Plug the XM radio
harness 6-pin connector into the fuse box 6-pin
connector.
27. Install the XM radio harness fuse cases and the
6-pin dummy connector to the fuse box case.
Fuse case position
NOTE: If the 6-pin connector is already being used
by another accessory, locate the 6-pin connector
taped to the XM radio harness. Remove the
dummy connector from the harness, and plug the
other accessory's harness 6-pin connector into the
XM radio harness.
FUSE
CASES
VEHICLE
HARNESS
(Do not
secure
to the
yellow
SRS
harness.)
OTHER
ACCESSORY
6-PIN
HARNESS
XM RADIO HARNESS
6-PIN CONNECTOR
WIRE TIE
XM RADIO
HARNESS
DUMMY
CONNECTOR
(Discard.)
2524060M
2N28020M
6-PIN
CONNECTOR
FUSE BOX
6-PIN
CONNECTOR
FUSE
CASES
XM RADIO HARNESS
6-PIN CONNECTOR
WITH DUMMY
CONNECTOR
28. Secure the XM radio harness to the vehicle
harness with one wire tie. Do not secure it to the
yellow SRS harness.
29. Route the XM radio harness under the steering
shaft and toward the center console.
VEHICLE HARNESS
FUSE
LABEL
2A
LABEL
XM RADIO
HARNESS
CLIP
5A
LABEL
2524051M
WIRE TIES (3)
FUSE LABEL
CENTER
CONSOLE
XM RADIO
HARNESS
3121030M
Use these
labels.
2N28030M
26. Attach the fuse labels to the fuse cases on the
XM radio harness.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
29. Loosely attach the XM radio harness to the
vehicle harness with three wire ties.
AII 25749 (0402)
11 of 22
30. Inside the center console, locate the welded nut
on the vehicle stay. Attach the XM radio harness
ground terminal to the welded nut with the ground
bolt supplied.
33. Attach the modulator bracket to the player basebracket with two 5 x 10 mm washers and two
5 mm flange nuts.
WIRE TIE
CUSHION TAPE
HALF
CUSHION
TAPE
MODULATOR
BRACKET
Cut
GROUND
BOLT
5 mm
FLANGE
NUT
Clean with
isopropyl
alcohol.
VEHICLE
HARNESS
PLAYER
BASEBRACKET
3-PIN
CONNECTOR
GROUND
TERMINAL
XM RADIO
HARNESS
HALF
CUSHION TAPE
3606010M
31. Secure the XM radio harness to the vehicle
harness with one wire tie. Route the 3-pin
connector, and the remaining end of the XM radio
harness toward the rear of the vehicle; they will be
routed later.
FM Modulator Unit Installation
32. To protect the center panel, attach masking tape
to the center panel in the area shown.
5 x 10 mm
WASHERSCREW
3605060M
34. Using scissors, cut one cushion tape in half.
Using isopropyl alcohol, clean the bonding
surfaces of the brackets, and attach the half
cushion tapes to the brackets in the area shown.
35. Install the FM modulator unit to the modulator
bracket with two 4 x 8 mm washer-screws. Attach
the connector clip from the FM modular unit
harness into the hole in the player base-bracket.
CENTER
PANEL
FM MODULATOR
BRACKET
4 x 8 mm
WASHERSCREW
MASKING
TAPE
MODULATOR
BRACKET
4 x 8 mm
WASHERSCREW
HOLE OF THE
MODULATOR
BRACKET
PLAYER BASE
BRACKET
2506010T
3605071M
CONNECTOR CLIP
12 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
36. Insert the studs from the player base-bracket into
the holes in the vehicle frame from the back, then
install the two 6 mm flange nuts while holding the
bracket firmly against the vehicle frame.
39. Unplug the vehicle antenna cable, and plug it into
the FM modulator unit antenna cable. Plug the
other end of the FM module antenna jack into the
vehicle antenna cable.
WIRE TIE
WIRE TIE
VEHICLE
HARNESS
PLAYER
BASE-BRACKET
VEHICLE
HARNESS
WIRE
TIE
EXCESS
ANTENNA
CABLE
EPT
SEALER
VEHICLE
FRAME
6 mm FLANGE
NUTS (2)
3605081M
37. Connect the XM radio harness 3-pin connector to
the FM modulator unit harness 3-pin connector.
38. Get a DIN cable from the XM radio attachment.
Plug the 90° end of the DIN cable connector into
the FM modulator unit, then route the DIN cable
rearward along the XM radio harness .
XM RADIO
HARNESS
3-PIN
CONNECTOR
3606042M
FM MODULATOR
ANTENNA CABLE
FM MODULATOR
UNIT
DIN
CABLE
VEHICLE
ANTENNA
CABLE
40. Wrap one EPT sealer around the antenna jack,
and secure the antenna cable to the vehicle
antenna cable with the one wire tie. Secure both
antenna cables to the vehicle harness with one
wire tie.
41. Loop the excess antenna cable from the
FM modulator, and secure the excess cable to
the vehicle harness with two wire ties.
FM MODULATOR
UNIT HARNESS
CONNECTOR
3609041M
XM RADIO
HARNESS
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
13 of 22
42. Plug the display module cable into the FM
modulator unit. Pull the excess length of the cable
out from under the display module unit.
45. Loop the excess display module cable along the
DIN cable and the vehicle harness, then secure
the display module cable, and the DIN cable with
one wire tie with clip. Insert the clip from the wire
tie into the modulator bracket hole.
MODULATOR
BRACKET HOLE
DISPLAY
MODULE UNIT
DISPLAY MODULE
CABLE
WIRE TIE
WITH CLIP
XM RADIO
HARNESS
DISPLAY
MODULE
CABLE
(Pull out.)
REAR
3606052M
WIRE TIE
WIRE TIE
43. If equipped with a player, plug the BUS cable
connector into the vehicle connector.
3606061M
DIN CABLE
46. Near the subbracket, secure the XM radio harness
to the vehicle harness with one wire tie.
PLAYER BUS
CABLE
CONNECTOR
(If equipped.)
47. Secure the excess length of DIN cable and
XM radio harness to the vehicle harness with two
wire ties.
48. If the vehicle is not equipped with a player, attach
the two grommet screws to the player panel in the
square holes as shown.
PLAYER
PANEL
6 mm FLANGE
NUTS (4)
3618021M
44. Install the display module assembly onto the
studs from the left and right player subbrackets,
and install the 6 mm flange nuts. Tighten the
flange nuts securely.
14 of 22
GROMMET SCREW
AII 25749 (0402)
2306131T
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
49. Get one EPT sealer. Measure the EPT sealer as
shown, and cut it into three pieces.
EPT SEALER
(Cut off the
marked area.)
52. Inside the passengers' compartment, remove the
rear seat cushion by removing the bolt and
releasing the two locks (pull the lock out toward
you).
PLAYER
PANEL
BOLT
8 mm
REAR SEAT
CUSHION
8 mm
EPT SEALER
HOOKS (2)
(Pull down.)
2612010T
2527020T
LOCKS (2)
50. Using isopropyl alcohol on a shop towel, clean the
player panel in the area shown. Attach the two cut
pieces of the EPT sealer to the player panel, and
cut off the excess.
51. Attach the player panel by inserting the clips into
the latches, and install two self-tapping screws
from the kit, or reinstall the two self-tapping
screws you removed in step 13. Remove the
masking tape.
CLIP
LEVERS (2)
(Pull out.)
53. Inside the trunk, fold the right and left seatbacks
down by pulling the strap and pushing forward on
the seat.
LEFT REAR
SEAT CUSHION
STRAP
LATCH
PLAYER
PANEL
SELFTAPPING
SCREW
(Reuse.)
2306141T
2527030T
RIGHT REAR
SEAT BACK
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 25749 (0402)
15 of 22
54. Remove the spare tire cover (one clip).
56. Remove the jack cover and the jack.
CLIP
JACK
SPARE TIRE
COVER
JACK COVER
2527051T
3730010M
55. Remove the trunk weatherstrip in the area shown,
then remove the rear trim panel (four clips).
57. Remove the hook from the right side trunk liner
(one bolt , hook and washer).
WASHER
CLIPS (4)
REAR
TRIM
PANEL
HOOK
RIGHT SIDE
TRUNK LINER
THREADED
HOOK
BOLT
CLIP
TRUNK
WEATHERSTRIP
(Remove.)
SELF-TAPPING
HOOKS (3)
2527061T
2527073T
58. Remove the right side trunk liner (three selftapping hooks, one threaded hook and one clip).
16 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
58. Inside the trunk area, unplug the high mount brake
light harness connector. Inside the cabin, remove
the high mount brake light from the rear shelf by
releasing the four hooks, and pulling out the brake
light assembly. Take care not to damage the clips.
60. Raise the rear seat back. Pull the XM radio
harness and DIN cable out from under the floor
carpet and toward the passengers' side of the
vehicle. Secure the XM radio harness and the DIN
cable to the vehicle harness with two wire ties.
DIN CABLE
HIGH-MOUNT
BRAKELIGHT
HOOKS (4)
REAR
SHELF
VEHICLE
CLIP
XM
RADIO
HARNESS
BULB
(If necessary.)
3620010M
CONNECTOR
WIRE TIE
3619060M
59. Route the XM radio harness and the DIN cable
along the vehicle harness toward the parking
brake lever, and under the floor carpet. Secure the
XM radio harness and the DIN cable to the vehicle
harness with two wire ties in the areas shown.
XM RADIO HARNESS
AND DIN CABLE
WIRE TIE
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
3609010M
AII 25749 (0402)
17 of 22
61. Continue routing the XM radio harness and DIN
cable along the vehicle harness toward the trunk.
Using isopropyl alcohol, clean the areas where
the cushion tapes will attach, then secure the
XM radio harness and DIN cable to the vehicle
panel with five cushion tapes.
63. Inside the trunk, install the two wire ties with clip
to the DIN cable, and XM radio harness, and push
the clips into the holes in the bulkhead.
WIRE TIE WITH
CLIPS (2)
CUSHION TAPE
BULKHEAD
CUSHION
TAPE
BULKHEAD
HOLES (2)
CABLE
CUSHION
TAPES (5)
3620021M
62. Using isopropyl alcohol, clean the bulkhead area
where the cushion tape will attach. To prevent
damage to the XM radio harness and DIN cable,
attach the cushion tape to the bulkhead edge in
the area shown.
BULKHEAD
XM RADIO
HARNESS
3620031M
64. Using isopropyl alcohol on a shop towel, clean the
area where the cushion tape will attach. Attach the
DIN cable and XM radio harness to the vehicle
frame with one cushion tape.
Installing the Antenna
65. Get the antenna kit. Route the antenna cable into
the trunk area through the high-mount brakelight
opening. Clean the edge of the rear shelf, and
attach one cushion tape to the edge of the rear
shelf.
REAR SHELF
CUSHION
TAPE
ANTENNA
ANTENNA
CABLE
HIGH-MOUNT
BRAKELIGHT
OPENING
18 of 22
AII 25749 (0402)
3619111M
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
66. Temporarily fit the high-mount brake light onto the
rear shelf.
69. Route the antenna cable through the groove in the
high mount brake light case, and reinstall the high
mount brake light case.
HIGH-MOUNT
BRAKE LIGHT
CASE
HIGH-MOUNT
BRAKE LIGHT
CASE
REAR TRAY BRAKE LIGHT
OPENING
CASE
GROOVE
ANTENNA
ANTENNA
CABLE
Clean with
isopropyl
3627010M
3620043M
FRONT
Align
FASTENER
70. Route the antenna cable along the vehicle
harness, and secure it to the vehicle harness with
seven wire ties in the areas shown.
67. Using isopropyl alcohol on a shop towel, clean the
bottom of the antenna. Remove the adhesive
backing from the fastener, then attach the fastener
to the bottom of the antenna. Attach the antenna
onto the rear rear shelf.
VEHICLE
HARNESS
WIRE TIES (7)
(Attach near the vehicle
harness clips.)
68. Measure and mark the high-mount brake light
case. Using a utility knife, cut a groove in the
brake light case. Remove any burrs from the
edges of the groove.
BRAKELIGHT
CASE
Cut.
5 mm
ANTENNA CABLE
10
mm
90
mm
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
VEHICLE
HARNESS CLIP
3620050M
3619071M
AII 25749 (0402)
19 of 22
71. Attach one wire tie with clip to the antenna cable,
the XM radio harness and the DIN cable in the
area shown. Push the clip from the wire tie with
clip into the body hole.
BODY
HOLE
WIRE TIE
WITH CLIP
72. Route the antenna cable, the XM radio harness,
and the DIN cable along the trunk side panel.
Loosely attach the three off-set wire ties with clip
around the antenna cable, the XM radio harness,
and the DIN cable, then push the clip from each
wire tie into the three holes in the trunk side panel.
TRUNK SIDE
PANEL HOLE
ANTENNA
CABLE
DIN CABLE
AND XM
RADIO
HARNESS
OFF-SET WIRE
TIE WITH CLIP
(Note the installation
direction.)
PANEL EDGE
EPT SEALER
(Clean this
surface with
isopropyl
alcohol.)
DIN CABLE
XM RADIO
HARNESS
TRUNK
SIDE
PANEL
ANTENNA
CABLE
3620060M
ANTENNA
CABLE
DIN CABLE
OFF-SET
WIRE TIE WITH
CLIP (2)
(Note the
installation
direction.)
TRUNK SIDE
PANEL HOLE
XM RADIO
HARNESS
3620071M
73. Using isopropyl alcohol on a shop towel, clean the
bonding surface on the panel edge, attach one
EPT sealer to the panel edge in the area shown.
20 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
74. Install the upper and lower unit brackets to the
receiver unit using two 4 x 8 mm washer-screws,
and two 4 mm flange nuts for each bracket.
4 mm
FLANGE NUT
76. Secure the antenna cable, the XM radio harness,
and the DIN cable with two wire ties with clip at
the measurement shown. Press the clips of the
wire ties into the trunk side panel hole and upper
unit bracket hole.
4 mm
FLANGE NUT
SCREW
POSITION
SCREW
POSITION
TRUNK SIDE
PANEL HOLE
WIRE TIE
WITH CLIPS (2)
ANTENNA
CABLE
240 mm
UPPER
UNIT
BRACKET
LOWER
UNIT
BRACKET
RECEIVER
UNIT
4 x 8 mm
WASHERSCREW
WIRE
TIE
WITH
CLIP
4 x 8 mm
WASHERSCREW
UPPER
UNIT
BRACKET
HOLE
3623031M
–
DIN CABLE
LOWER UNIT
BRACKET HOLE
75. Position the receiver unit between the right trunk
side panel and the rear fender panel, and plug in
the antenna cable connectors, the DIN cable
connector, and the XM radio harness connector
using the panel hole to access the receiver unit.
BLACK
CONNECTOR
DIN CABLE
XM RADIO
HARNESS
= 240 mm
3730020M
77. Fold the excess DIN cable, and secure it to the
lower unit bracket with one wire tie with clip.
78 Attach the receiver unit/brackets using two
6 x 12 mm washer-bolts through the trunk side
panel holes. Tighten the bolts securely.
ANTENNA
CABLE
TRUNK SIDE
PANEL HOLE
ANTENNA
CABLE
DIN
CABLE
XM RADIO
HARNESS
6 x 12 mm
WASHERBOLT
RECEIVER
UNIT
3619092M
3619080M
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
6 x 12 mm
WASHERBOLTS (2)
AII 25749 (0402)
21 of 22
79. Fold any excess antenna cable, and wrap the
excess cable with two EPT sealers. Secure the
antenna cable to the XM radio harness with two
wire ties in the areas shown. Tighten the off set
wire ties you loosely installed in step72.
81. Attach the 5A fuse label over the No. 33 position
on the fuse box cover.
FUSE LABEL (5A)
FUSE BOX COVER
No.33
OFF SET WIRE
TIE WITH CLIP
2219090T
82. Check that all wire harnesses and cables are
routed properly and all connectors are plugged in.
XM RADIO
HARNESS
83. Reinstall all removed parts. Check that all clips
and fasteners are installed securely.
EPT
SEALERS
(2)
ANTENNA
CORD
84. Reconnect the negative cable to the battery.
WIRE TIE
3623012M
80. Install the 5A fuse provided into the No. 33 slot of
the fuse box.
85. Enter the radio anti-theft code, and reset the
customer's radio station presets.
86. Set the clock.
87. Set one of the radio station presets to FM 88.7,
and check the operation of the XM radio. If
necessary, use the XM radio Owner’s Manual
supplied.
FUSE BOX
FUSE (5A)
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO up function is disabled.
88. Do the driver's window AUTO up procedure:
•
Start the engine. Push down on the driver’s
window switch until the window is fully open.
•
Pull up on the driver’s window switch to close
the window completely, and hold the switch for
2 seconds or more.
•
Test the window AUTO up function.
2219080T
22 of 22
AII 25749 (0402)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement