AlphaServer 8200 Systems V2.3

AlphaServer 8200 Systems V2.3

TM

AlphaServer 8200 Systems V2.3

Digital Systems and Options Catalog

Digital believes the information in this publication is accurate as of its publication date; such information is subject to change without notice. Digital is not responsible for any inadvertent errors.

Digital conducts its business in a manner that conserves the environment and protects the safety and health of its employees, customers, and the community.

Digital, the DIGITAL logo are trademarks of Digital Equipment Corporation.

Printed in U.S.A. Copyright 1996 Digital Equipment Corporation. All rights reserved.

Digital AlphaServer 8200 Systems

AlphaServer 8200 Systems

Product Description

AlphaServer 8200 is the highest performance office system in the industry. It can be configured with up to six of the world’s fastest microprocessors (Alpha microprocessor 21164) with 5/300 MHz or 5/350 MHz CPUs. With the enormous capacity of the Alpha 64-bit architecture—up to 6 Gbytes of memory, and PCI I/O of up to 108 slots—this server offers room for growth for the largest and most complex applications.

AlphaServer 8200 runs Digital UNIX or OpenVMS operating systems and offers the reliability and availability features customers require for bet-your-business environments. Clusters, hot swap disks, RAID, redundant power, ECC memory and data paths, fault management, and uninterruptible power system are all available.

Small enterprises and large departments can have an office server with unprecedented performance, capacity, and reliability for those applications previously available on enterprise systems. Large databases, complex simulations, data warehousing, and decision support are a few examples of the kinds of applications the AlphaServer 8200 can support with ease. And, with up to 6 Gbytes of memory, this office server can provide all the benefits that Very

Large Memory/Very Large Database (VLM/VLDB) systems have provided in the past.

For technical/scientific users, the AlphaServer 8200 provides supercomputer performance in the office. The AlphaServer 8200 has single processor floatingpoint performance that dominates the competition in the generic benchmarks and wins at the application level as well.

Alpha Servers 1.193

AlphaServer 8200 Systems

Step 1—Base Servers

Systems require Digital UNIX V3.2B or later, and OpenVMS V6.2 or later. Software media and documentation required for first system on site. See Step 13 for ordering information.

Console terminal required to install system. See Step 10 unless terminal is available on site.

Base Servers include 5 slot backplane—three slots are used by CPU module, memory module, and

KFTIA-AA system I/O module.

- Two slots available for additional CPU, memory, or system I/O module(s).

CD-ROM drive and RZ28D-VA SCSI disk drive included in BA656 Internal Storage Drawer are connected via singleended SCSI-2 port on KFTIA-AA system I/O module.

- Four additional narrow 3.5-inch StorageWorks devices can be added in BA656 Internal Storage Drawer.

Universal Single-Phase power supply supplies necessary power for system; requires selection of power cord from

Step 2.

Redundant power supply (N+1) can be added if required.

For recommended power protection, UPS products, see section following Specifications.

AlphaServer 8200 5/300 and 5/350 Base Servers include:

Processor module with one or two Alpha microprocessor 21164 5/300 or 5/350 MHz CPUs; each includes 4-Mbyte Backup cache

System I/O module (KFTIA-AA) includes

- Two twisted-pair 802.3/Ethernet

- Single-ended SCSI-2 port

- Three Fast Wide Differential (FWD) SCSI-2 ports

Three CK-KFTIA-AA Cabinet Kits

128, 256, 512 Mbytes, or 2 Gbytes of memory

BA656 Internal Storage Drawer

RZ28D-VA 2-Gbyte 3.5-inch SCSI disk drive

600-Mbyte CD-ROM drive

5/300 MHz Servers

Single-CPU Systems

DA-281AB-A9

DA-281AD-A9

DY-281AB-A9

DY-281AD-A9

Dual-CPU Systems

DA-281BB-A9

DA-281BC-A9

DA-281BD-A9

DA-281BF-A9

DY-281BB-A9

DY-281BC-A9

DY-281BD-A9

DY-281BF-A9

5/350 MHz Servers

DA-281CB-A9

DA-281CD-A9

DY-281CB-A9

DY-281CD-A9

DA-281DB-A9

DA-281DC-A9

DA-281DD-A9

DA-281DF-A9

DY-281DB-A9

DY-281DC-A9

DY-281DD-A9

DY-281DF-A9

Operating System

Digital UNIX

Digital UNIX

OpenVMS

OpenVMS

Digital UNIX

Digital UNIX

Digital UNIX

Digital UNIX

OpenVMS

OpenVMS

OpenVMS

OpenVMS

Universal single phase power

48 VDC power supply

Shielded console cable included for connection to console terminal (BC16E-25)

Factory Installed Software

Operating System Software

- Digital UNIX base license or

- OpenVMS base license

Digital NAS Base Server 200 software

One year hardware product warranty

90-day software product warranty

Memory

128 Mbytes

512 Mbytes

128 Mbytes

512 Mbytes

128 Mbytes

256 Mbytes

512 Mbytes

2 Gbytes

128 Mbytes

256 Mbytes

512 Mbytes

2 Gbytes

1.194 Alpha Servers

AlphaServer 8200 Systems

Step 1—AlphaServer 8200 Systems (continued)

AlphaServer 8200 5/350 Expanded Base Server includes:

Processor module with two Alpha microprocessor 21164

5/350 MHz CPUs; each includes 4-Mbyte Backup cache

System I/O module with four I/O channels (KFTHA-AA)

PCI Shelf Mount Box (DWLPA-CA)

PCI Fast Wide Differential (FWD) SCSI Adapter

(KZPSA-BB)

Digital Etherworks 32-bit Network Interface Card

(DE435-AA)

512 Mbytes of memory

BA656 Internal Storage Drawer

SCSI-2 16-bit wide StorageWorks shelf (BA356-JB)

StorageWorks SCSI Signal Converter (DWZZB-VW)

BN21K-01 Fast Wide Differential cable

RZ28D-VW 2-Gbyte 3.5-inch SCSI disk drive

(located in BA356-JB)

600-Mbyte CD-ROM drive

PCI single-ended SCSI controller (KZPAA-AA) and

BN21H-02 SCSI cable (connects to CD-ROM)

Universal single phase power

48 VDC power supply

Shielded console cable included for connection to console terminal

Factory Installed Software

Operating System Software

- Digital UNIX base license or

- OpenVMS base license

Digital NAS Base Server 200 software

One year hardware product warranty

90 day software product warranty

5/350 MHz Servers (Dual-CPU)

DA-281DD-B9

DY-281DD-B9

Operating System

Digital UNIX

OpenVMS

Memory

512 Mbytes

512 Mbytes

Step 1a—AlphaServer 8200 5/300 System Building Blocks

Note: System Building Blocks are an alternative to standard Base Servers; they provide flexibility in configuring the

AlphaServer 8200 with a choice of memory and I/O options.

System Building Block Requirements

- System I/O module

Systems require Digital UNIX V3.2B or later, and OpenVMS V6.2 or later.

Console terminal required unless available on site.

System includes 5 slot backplane—three slots are used by CPU, memory and system I/O modules.

- Two slots available for additional CPU, memory, or system I/O module(s).

CD-ROM drive included in BA656 Internal Storage Drawer—SCSI controller must be ordered separately.

- BA656 Internal Storage Drawer is restricted to CD-ROM drive only when KZPAA is selected.

- If KFTHA-AA I/O module is selected, the following items must be ordered to provide interface to CD-ROM in BA656 internal storage drawer. If KFTIA-AA I/O module is selected these items are not required.

DWLPA-CA

KZPAA-AA

PCI shelf mount box; AlphaServer 8200 system cabinet only, maximum three per cabinet.

PCI single-ended SCSI controller for CD-ROM connection only—no other SCSI options can be installed in BA656 internal storage drawer if KZPAA is used as CD-ROM interface. KZPAA is restricted as CD-ROM connection only, no other disk of tape connections supported—maximum one per system.

SCSI cable

BN21H-02

If Factory Installed Software is required, BA350-JB/BA356-JB and appropriate disk drive and controller must be ordered separately.

Universal single phase power supply will supply necessary power for system.

Redundant power supply (N+1) can be added if required.

Minimum of one memory module and one system I/O module must be ordered separately.

Alpha Servers 1.195

AlphaServer 8200 Systems

Step 1a—AlphaServer 8200 5/300 System Building Blocks (continued)

AlphaServer 8200 5/300 System Building Blocks include

Processor module with one or two Alpha microprocessor

21164/300 MHz CPU(s); each includes 4-Mbyte Backup cache

BA656 Internal Storage Drawer

600-Mbyte CD-ROM drive

Universal single phase power

48 VDC power supply

Order Number

DA-281AY-A9

DY-281AY-A9

DA-281BY-A9

DY-281BY-A9

Operating System

Digital UNIX

OpenVMS

Digital UNIX

OpenVMS

CPU

Single-CPU Systems

Single-CPU Systems

Dual-CPU Systems

Dual-CPU Systems

Operating System Software

- Digital UNIX base license or

- OpenVMS base license

Digital NAS Base Server 200 software

One year hardware product warranty

90 day software product warranty

Memory

Required

Required

Required

Required

I/O Module

Required

Required

Required

Required

Step 1b—AlphaServer Expansion Packages—Digital UNIX systems only

The DECsafe package contains all necessary hardware (excluding console terminal) and software to provide a complete and operational system in a DECsafe high availability environment. Note: This package is only orderable with a Digital

UNIX system configuration. It is not orderable as a stand alone, upgrade, or spared on the order.

8YFEB-EX

DECsafe High Availability SCSI Package includes:

Six RZ28D-VW 2.1-Gbyte, 3.5-inch disk drives in BA356-JB shelf

TZ87 20-Gbyte, 5.25-inch SCSI tape drive in second BA356-JB shelf

Two DWZZB-VWs to convert FWD (Fast Wide Differential) SCSI signals

from KFTIA-AA and KZPSA-BB for use in BA356-JB shelf

PCI Plug-in unit (DWLPA-CA), with KZPSA-BB FWD (Fast Wide Differential) SCSI adapter

BN21K cables and CK-KFTIA-AA cable kit

DECsafe Available Server software license kit

Step 2—Power Cord

BN23H-4E

BN20P-4E

60 Hz

AC line cord for Single Phase Power, one per cabinet (4.5 meters in length)

50 Hz

AC line cord for Single Phase Power, one per cabinet (4.5 meters in length)

Note: See Specifications for information on appropriate power cord to order. If redundant supply (H7266-AD/AE) is ordered, power cord is included and does not have to be ordered separately.

Step 3—Additional CPU Modules (SMP Upgrades)

Up to two additional CPU modules can be added to Base Servers, Expanded Base Servers and System Building

Blocks—system maximum of three CPU modules.

Combining 5/300 MHz and 5/350 MHz CPU modules in the same system is not supported.

For more than two processor modules in a system, a minimum of two memory modules are recommended for optimal system performance.

All SMP upgrades include processor module with Alpha microprocessor 21164 5/300 or 5/350 MHz CPU(s), SMP extension license, and end-user product warranty.

5/300 MHz Servers 5/350 MHz Servers

751P2-AX

752P2-AX

751P1-AX

752P1-AX

753P2-AX

754P2-AX

753P1-AX

754P1-AX

Operating System

Digital UNIX

Digital UNIX

OpenVMS

OpenVMS

CPU Module Type

Single-CPU

Dual-CPU

Single-CPU

Dual-CPU

1.196 Alpha Servers

AlphaServer 8200 Systems

Step 4—Memory

Maximum of 6 Gbytes per system. Note: A short term memory size restriction is currently in effect for 5/300 MHz systems

only. Memory modules must be ordered in a quantity of one or two of the same size—add-on memory size must be the same as that included with Base Server or Expanded Base Server selected or the initial memory module selected for a

System Building Block configuration. The maximum memory supported is temporarily two 2-Gbyte memory modules, resulting in a system maximum of 4 Gbytes.

For Base Servers two additional memory modules can be added for a system maximum of three.

System Building Blocks require the selection of one memory module—system maximum of three.

The maximum of three memory modules is reduced by one for each additional CPU module selected from Step 3 and each system I/O module added from Step 6.

Each memory module has built in two-way interleaving; additional interleaving is accomplished by adding more memory modules.

MS7CC-BA

MS7CC-CA

MS7CC-DA

MS7CC-EA

MS7CC-FA

128-Mbyte memory module

256-Mbyte memory module

512-Mbyte memory module

1073-Mbyte memory module

2147-Mbyte memory module

Step 4a—Memory Upgrades

Memory upgrades are field installed only (not configured in Manufacturing).

MS7CC-UA

MS7CC-UB

128-Mbyte memory upgrade (8-Mbyte SIMMs); upgrades 128-Mbyte (-BA) module to

256-Mbyte (-CA) module

512-Mbyte memory upgrade (32-Mbyte SIMMs); upgrades 512-Mbyte (-DA) module to

1-Gbyte (-EA) module

Step 4b—Prestoserve Nonvolatile Random Access Memory (NVRAM)

Supported on Digital UNIX systems only.

Maximum one Prestoserve I/O performance enhancement option per system.

Includes Prestoserve license and documentation kit.

DJ-ML200-BA

DJ-ML200-CA

DJ-ML300-BA

4-Mbyte Prestoserve, PCI option—requires DWLPA-CA/CB

8-Mbyte Prestoserve, PCI option—requires DWLPA-CA/CB

4-Mbyte Prestoserve, KFTIA-AA daughter card mounting—requires KFTIA-AA

Step 5—I/O Expansion Buses

PCI I/O bus is available on AlphaServer 8200. Application and system configuration determine maximum configuration.

Configuration limits exist at I/O bus level and controller level. Verify maximum number of allowable controllers listed in

Controller Configuration Table.

Each DWLPA-CA/CB (PCI shelf mount box) includes 12 PCI slots and required cable for connection to I/O channel.

Each PCI shelf mount box requires one I/O channel connection to KFTHA-AA or KFTIA-AA, see Step 6.

Maximum of nine I/O channels available.

DWLPA-CA

DWLPA-CB

KFE70-BA

PCI shelf mount box for AlphaServer 8200 system cabinet only—maximum three per cabinet.

PCI shelf mount box for AlphaServer 8200 expansion cabinet only—maximum four per cabinet.

EISA Bridge option; PCI to EISA bridge module set—must reside in first DWLPA-CA in system cabinet only. Converts 12-slot PCI bus to 2 EISA, 6 PCI/EISA, and 2 PCI slots. Includes RX26 diskette drive, mounting hardware, and cables to mount RX26 in processor system unit. Maximum one EISA Bridge option supported per system. This option is required to support KZPSC SCSI RAID controllers. It includes diskette drive required to run the RAID Configuration Utility (RCU).

Alpha Servers 1.197

AlphaServer 8200 Systems

Step 6—System I/O Modules

KFTIA-AA system I/O module included with Base Server; KFTHA-AA included with Expanded Base Server—any combination of KFTIA or KFTHA modules can be added for a system maximum of three.

- Maximum nine I/O channels available on AlphaServer 8200 (two KFTHA-AA modules, one KFTIA-AA module).

System Building Block requires the selection of one I/O module.

KFTHA-AA

KFTIA-AA

System I/O module with four I/O channels for DWLPA-CA/CB boxes.

System I/O module with one I/O channel for DWLPA-CA/CB shelf mount box, includes

- two 802.3 twisted-pair Ethernet ports—requires BN26M cable per port

BN26M-xx

BN21H-xx

CK-KFTIA-AA

BN21K-xx

–BN21K-02*

–BN21K-03*

–BN21K-05/10

- three FWD (Fast Wide Differential) SCSI-2 ports—requires CK-KFTIA-AA and BN21K cable per port (Note: Base Servers include KFTIA-AA with three CK-KFTIA-AA cabinet kits.)

One of the following optional FDDI daughter cards can be added to KFTIA-AA—see Step 9 for cables.

- Single attachment station multi-mode fiber card (DEFPZ-AA) or

- Twisted-pair copper card (DEFPZ-UA)

Prestoserve (DJ-ML300-BA) can be added to KFTIA-AA.

Ethernet twisted-pair cable; 8-pin MP to 8-pin MP, screened, EIA/TIA Category 5 cable

SCSI-2 single-ended cable; 50-pin male straight to 50-pin male straight. Connects KFTIA-AA single-ended SCSI-2 port to StorageWorks shelf.

Cabinet kit for Fast Wide Differential (FWD) SCSI-2 port. One kit required for each used port on

KFTIA -AA—maximum three per KFTIA-AA. Cabinet kit includes Y-cable and FWD terminator.

SCSI-2 Fast Wide Differential cables; 68-pin male straight to 68-pin male right-angle. Connects

KFTIA-AA FWD SCSI-2 ports to DWZZA-VA or DWZZB-VW (cable lengths in meters).

Connects from KFTIA FWD port to DWZZA-VA in BA350-JB in system cabinet (front)

DWZZB-VW in BA356-JB in system cabinet (front)

Connects from KFTIA FWD port to DWZZA-VA in BA350-JB in system cabinet (rear)

DWZZB-VW in BA356-JB in system cabinet (rear)

Connects from KFTIA FWD port to DWZZA-VA in BA350-JB in expansion cabinet (front or rear)

DWZZB-VW in BA356-JB in expansion cabinet (front or rear)

Connects from KFTIA FWD port to DWZZA-VA in BA350-JA in SW500 and SW800 Cabinets

DWZZB-VW in BA356-SB in SW500 and SW800 Cabinets

* Manufacturing may substitute correct cable length depending on configuration.

Step 7—Storage Controllers

KFTIA-AA I/O module included with Base Server; KFTHA-AA I/O module included with Expanded Base Server;

System Building Blocks require I/O module.

DWZZA-VA Fast Wide Differential to Fast Narrow Single Ended SCSI Converter requires minimum revision F02 for connecting FWD signals from KFTIA-AA and KZPSA-BB to BA350-JB StorageWorks shelf.

DWZZA-AA requires minimum revision E02 for connecting any Fast Wide Differential SCSI-2 port from KFTIA-AA or KZPSA-BB to externally mounted TZ8xx tape loaders.

DWZZB-VW Fast Wide Differential Single-ended SCSI Converter requires minimum revision A01 for connecting

FWD SCSI-2 signals from KFTIA-AA or KZPSA-BB to BA356-JB StorageWorks Shelf.

System maximum of two KZPSC-AA/BA SCSI RAID controllers.

Tape and optical devices are not supported on KZPSC SCSI RAID controllers.

Storage Controllers

PCI-based

KZPSA-BB

BN21K-xx

–BN21K-01*

–BN21K-02*

–BN21K-03*

–BN21K-05/10

PCI Fast Wide Differential SCSI Adapter. OpenVMS supports seven per PCI, maximum seven per system. Digital UNIX supports eight per PCI, maximum 32 per system. (Requires one PCI slot.)

Provides one SCSI-2 bus. The KZPSA supports DECsafe Available Server.

SCSI-2 Fast Wide Differential cables; 68-pin male straight to 68-pin male right-angle. Connects

KZPSA-BB Fast Wide Differential SCSI-2 port to DWZZA-VA or DWZZB-VW.

Connects from KZPSA to DWZZA-VA in BA350-JB in system cabinet (front)

DWZZB-VW in BA356-JB in system cabinet (front)

Connects from KZPSA to DWZZA-VA in BA350-JB in system cabinet (rear)

DWZZB-VW in BA356-JB in system cabinet (rear)

Connects from KZPSA to DWZZA-VA in BA350-JB in expansion cabinet (front or rear)

DWZZB-VW in BA356-JB in expansion cabinet (front or rear)

Connects from KZPSA to DWZZA-VA in BA350-JA in SW500 and SW800 cabinets

DWZZB-VW in BA356-SB in SW500 and SW800 cabinets

1.198 Alpha Servers

AlphaServer 8200 Systems

Step 7—Storage Controllers (continued)

KZPSC-AA

BN31L-1E

BN31S-1E

KZPSC-BA

BN31K-0E

BN31L-1E

BN31S-1E

PCI SCSI RAID Controller with 1 port. OpenVMS and Digital UNIX support two per PCI, maximum two per system. (Requires one PCI slot, and KFE70-BA—EISA Bridge option). Provides one Fast/wide/single-ended connection. Allows RAID levels 0,1, and 5. Tape drives not supported.

1.5 meter single-ended narrow cable. For connections from KZPSC-AA to BA350-JB in system cabinet.

1.5 meter wide SCSI cable. For connections from PCI RAID controller to BA356-JB Wide SCSI

StorageWorks Shelf located in same cabinet.

PCI SCSI RAID Controller with 3 ports. OpenVMS and Digital UNIX support two per PCI, maximum two per system. (Requires two PCI slots, and KFE70-BA—EISA Bridge option). Provides three Fast/wide/single-ended connections. Allows RAID levels 0,1, and 5. Tape drives not supported.

Required for KZPSC-BA to use third port on module. Connects internally from KZPSC-BA module to second PCI slot/bulkhead.

1.5 meter single-ended narrow cable. For connections from PCI RAID controller to BA350-JB located in the same cabinet. One required for each used port on KZPSC-BA module.

1.5 meter single-ended wide SCSI cable. For connections from PCI RAID controller to BA356-JB

Wide SCSI StorageWorks Shelf located in same cabinet. One required for each used port on KZPSC-

BA module.

* Manufacturing may substitute correct cable length depending on configuration.

Step 8—Storage

Note: When multiple storage devices are configured with the system, specify which devices should be installed inside the system cabinet, inside the system expansion cabinet, or installed in the external StorageWorks cabinet. Line item sequencing will allow Manufacturing to configure storage options in the appropriate cabinet.

List storage options to be integrated in system cabinet immediately following system part number.

List storage options to be integrated in StorageWorks cabinet immediately following StorageWorks cabinet part number.

Order appropriate BN21x-xx SCSI cables for connecting controllers and storage options.

Step 8a—Internal Storage (System Cabinet)

Wide SCSI devices are supported in BA356-JB Wide SCSI StorageWorks shelves inside the System cabinet. They are also supported in external StorageWorks cabinets via BA356-SB rackmount options for the SW500 and SW800 cabinets. The

BA356-JB includes BA35X-HG 48V/150W DC power supply and BA35X-RD metric mounting hardware.

System cabinet provides space for up to six BA350 or BA356 StorageWorks shelves; each shelf holds a maximum of two

5.25-inch devices and one 3.5-inch device or seven 3.5-inch devices. Most configurations require a DWZZA-VA or

DWZZB-VW which counts as one 3.5-inch device.

DWZZA-VA is a Fast Wide Differential to Fast Narrow Single-Ended SCSI converter.

DWZZB-VW is a Fast Wide Differential to Fast Wide Single-Ended Converter.

BA656 Internal Storage Drawer included in base systems; provides space for four additional narrow 5400 RPM and

7200 RPM SCSI 3.5-inch devices.

BA350-JB and BA356-JB StorageWorks shelves support 5400 RPM and 7200 RPM disk drives.

Narrow SCSI Options (8-bit)

BA350-JB

DWZZA-VA

RZ26N-VA

RZ28M-VA

RZ28D-VA

RZ29B-VA

Narrow SCSI-2 StorageWorks Shelf—includes 48V/150W DC power supply, DC fans, and rackmounting hardware. Supports 8-bit narrow SCSI devices. See configuration limitations in

Step 11a.

Narrow SCSI-2 StorageWorks Signal Converter

 required to convert FWD signals from KFTIA-

AA and KZPSA-BB for use in the BA350-JB StorageWorks shelves.

1.05-Gbyte 8-bit 5400 RPM SCSI-2 disk drive in 3.5-inch carrier

2.1-Gbyte 8-bit 5400 RPM SCSI-2 disk drive in 3.5-inch carrier

2.1-Gbyte 8-bit 7200 RPM SCSI-2 disk drive in 3.5-inch carrier

4.3-Gbyte 8-bit 7200 RPM SCSI-2 disk drive in 3.5-inch carrier

Note: Currently shipping revision of BA350-JB no longer requires fan upgrade kit (BA35X-MJ) to support 7200 RPM drives.

Revision A01 BA350-JB StorageWorks shelves require fan upgrade to support 7200 RPM drives.

Alpha Servers 1.199

AlphaServer 8200 Systems

Step 8a—Internal Storage (System Cabinet) (continued)

Wide SCSI Options (16-bit)

BA356-JB

DWZZB-VW

BA356-SC

RZ26N-VW

RZ28M-VW

RZ28D-VW

RZ29B-VW

Wide SCSI-2 StorageWorks Shelf—includes 16-bit I/O personality module, 48V/150W DC power supply, DC fans, and rackmounting hardware. Supports 16-bit wide SCSI devices and some 8-bit narrow SCSI devices depending on compliance with minimum revision levels.

Wide SCSI-2 StorageWorks Signal Converter—required to convert FWD signals from KFTIA-AA and KZPSA-BB for use in the BA356-JB StorageWorks shelves.

8-bit I/O Personality Module—can be used in place of 16-bit I/O personality module for direct connection to narrow single-ended controllers.

1.05-Gbyte 16-bit 5400 RPM SCSI-2 disk drive in 3.5-inch carrier

2.1-Gbyte 16-bit 5400 RPM SCSI-2 disk drive in 3.5-inch carrier

2.1-Gbyte 16-bit 7200 RPM SCSI-2 disk drive in 3.5-inch carrier

4.3-Gbyte 16-bit 7200 RPM SCSI-2 disk drive in 3.5-inch carrier

Note: To ensure 16-bit wide SCSI operation, use wide SCSI drives with wide SCSI controllers in wide SCSI StorageWorks shelves with wide SCSI cables.

See Storage Devices—StorageWorks Supported Devices for 8-bit and 16-bit Expansion table for minimum hardware revision levels.

Tape Devices (Note: Tape and Optical Devices not supported on KZPSC SCSI RAID controller.)

TLZ07-VA

TKZ15-VA

TZ87-VA

TZ88N-VA

8.0-Gbyte DAT 3.5-inch SCSI tape drive in StorageWorks carrier

5/10-Gbyte Helical Scan 8-mm, 5.25-inch SCSI tape drive in StorageWorks carrier

20.0-Gbyte DLT 5.25-inch SCSI tape drive in StorageWorks carrier

20/40-Gbyte DLT 5.25-inch SCSI tape drive in StorageWorks carrier

Optical Disk

RWZ52-VA

1.3-Gbyte Optical Drive in StorageWorks carrier

Step 8b—External Storage (I/O Expansion Cabinet)

I/O expansion cabinet (H9B10-EA) provides space for a maximum of 16 BA350-JB/BA356-JB SCSI StorageWorks shelves and a maximum of four DWLPA-CB PCI shelf mount boxes. Disk and tape drives supported are the same as Step

8a Internal Storage. See configuration limitations in Step 11b.

Step 8c—External Storage

The following list describes available disk storage devices, capacities, and shelf type and available tape drives. These supported options can be added as required.

Storage Cabinets

SW5XX, SW8XX

SCSI Disk Drives

RZ26N-VA

RZ28M-VA, RZ28D-VA

RZ29B-VA

RZ26N-VW

RZ28M-VW, RZ28D-VW

RZ29B-VW

Capacity

6

227 Gbyte

1.05 Gbyte

2.1 Gbyte

4.3 Gbyte

1.05 Gbyte

2.1 Gbyte

4.3 Gbyte

Narrow

Narrow

Narrow

Wide

Wide

Wide

Tape Drives

TZ87, TZ857*, TZ877, TZ88,

TSZ07, TKZ15-VA, TLZ07, TKZ09,

See Storage Devices for ordering information.

TKZ60, TL810, TL820

Optical Libraries

RW525-ZA

RW531-ZC

RW532-ZF

RW536-ZF

RWZ52-FA

19-Gbyte Optical Library, 1 drive

38-Gbyte Optical Library, 2 drives

76-Gbyte Optical Library, 4 drives

170-Gbyte Optical Library, 4 drives

1.3-Gbyte Tabletop Optical Library

* Loader support for Digital UNIX is available via DECnsr.

1.200 Alpha Servers

AlphaServer 8200 Systems

Step 9—Networks and Communications

Two twisted-pair 802.3/Ethernet controllers on KFTIA-AA system I/O module are included with each Base Server; DE435 network interface card included with Expanded Base Server. See Step 7 for twisted-pair Ethernet cable part number.

Optional DEFPZ-AA/UA (FDDI) daughter card can be installed on KFTIA-AA system I/O module. Select additional devices if required. Note: Connection of system to Ethernet requires twisted-pair cable. See Network Products Guide for details.

LAN Communications Controllers

KFTIA-AA daughter cards

Maximum one FDDIcontroller daughter card per KFTIA-AA I/O module.

System maximum of three FDDIcontroller daughter cards.

DEFPZ-AA

BN24E-xx

BN24D-xx

DEFPZ-UA

BN26M-xx

BN26S-xx

FDDIcontroller Fiber - Single attachment station

 daughter card for mounting on KFTIA-AA.

Requires BN24x cable.

Fiber-Optic Cable, Dual 2.5mm Bayonet “ST” type connectors

Fiber-Optic Cable, Dual 2.5mm Bayonet “ST” type connector to FDDI “MIC” connector

FDDIcontroller Fiber - Twisted-pair copper

 daughter card for mounting on KFTIA-AA.

Requires BN26x cable.

8-pin MP to 8-pin MP, screened, EIA/TIA Category 5 cable

8-pin MP to 8-pin MP, screened, crossover, EIA/TIA Category 5 cable

LAN Communications Controllers

PCI based

Requires DWLPA-CA/CB, PCI shelf mount box.

System maximum of four DEFPA-AA/DA/UA FDDIcontrollers.

DE435-AA

Digital Etherworks 32-bit High Performance Network Interface Card

 supports twisted-pair, thick wire and ThinWire, (requires one PCI slot). OpenVMS and Digital UNIX support eight per

PCI, maximum eight per system. Requires appropriate cable.

DEFPA-AA

DEFPA -DA

BN34A-xx

BN34B-xx

BN34D-xx

DEFPA-UA

BN26M-xx

BN26S-xx

FDDIcontroller Fiber - Single attachment station MultiMode Fiber—(requires one PCI slot).

OpenVMS and Digital UNIX support four per PCI, maximum four per system. Requires BN34x

“SC” type connecting cable.

FDDIcontroller Fiber - Dual attachment station MultiMode Fiber—(requires one PCI slot).

OpenVMS and Digital UNIX support four per PCI, maximum four per system. Requires BN34x

“SC” type connecting cable.

MultiMode Fiber Optic Duplex cable

“SC” connector to “ST” connector

MultiMode Fiber Optic Duplex cable

“SC” connector to “SC” connector

MultiMode Fiber Optic Duplex cable

“SC” connector to “MIC” connector

FDDIcontroller Fiber - Single attachment station UTP—(requires one PCI slot). OpenVMS and

Digital UNIX support four per PCI, maximum four per system. Requires BN26x cable.

8-pin MP to 8-pin MP, screened, EIA/TIA Category 5 cable

8-pin MP to 8-pin MP, screened, crossover, EIA/TIA Category 5 cable

Alpha Servers 1.201

AlphaServer 8200 Systems

Step 9—Networks and Communications (continued)

LAN Communications Controllers

EISA based

Requires DWLPA-CA and KFE70-BA, EISA bridge module set.

See EISA Bus IRQ Address Table.

DNSES-AA

Synchronous Communications Controller—(requires one EISA slot). Digital UNIX and OpenVMS support one per EISA, maximum one per system. Requires BC19x cable.

BC19B-02

BC19D-02

BC19E-02

BC19F-02

DW300-AA

EIA-422-A/V.11 adapter cable; can be extended with BC55D-33

EIA-232-D/V.24 adapter cable; can be extended with BC22F-xx

EIA-423-A/V.10 adapter cable; can be extended with BC55D-33

V.35 adapter cable; can be extended with BC19L-25

Token Ring Adapter—(requires one EISA slot) Digital UNIX supports one per EISA, maximum one per system. Requires BN26M cable.

BN26M-xx

802.5/Token Ring twisted-pair cable; 8-pin MP to 8-pin MP, screened, EIA/TIA Category 5 cable

CXI01-AA

CXI01-AB

CXI01-AD

CXI01-AE

CXI01-AC

CXI01-AF

Digiboard Asynchronous Xem/ISA Multiport Serial Card with 16 RJ45 PORTS/Xem Port

(requires one EISA slot) supports one per EISA, maximum one CXI01-AA/AD per system.

Supported on Digital UNIX systems only.

Digiboard PORTS/Xem, 16 RJ45 Port Concentrator—mounts separately from PCI bus.

Maximum of three CXI01-AB can be attached to CXI01-AA; provides up to 48 additional ports.

Supported on Digital UNIX systems only.

Digiboard Asynchronous EPC/X Multiport Serial Card with 16 RJ45 Port EPC/CON-16

Concentrator—(requires one EISA slot) supports one per EISA, maximum one CXI01-AA/AD per system. Supported on Digital UNIX systems only.

Digiboard EPC/CON-16 Concentrator—mounts separately from PCI bus. Maximum of three

CXI01-AE can be attached to CXI01-AD; provides up to 48 additional ports. Supported on Digital

UNIX systems only.

Digiboard RJ45 to DB25 Male Converter

Digiboard RJ45 to DECMJ11 Adapter—Eight per package

Local and Wide Area Communications Servers

Each communications server requires 802.3/Ethernet connection. Depending on server selected, either ThinWire BNC-type connection (e.g., BC16M cable) or thick wire 15-pin AUI transceiver cable (e.g., BNE3x) is required. Additional items also required—see the Network Products Guide.

Network Connectivity Products

See Network Products Guide for details.

Step 10—Console Terminal

Console terminal with EIA-232 25-pin DSUB connector and printer required unless otherwise available.

Shielded console cable is included for connection to the console terminal.

VT510-xx

LA30N-xx

LK411-xx

VT510 terminal

LA30 printer

Keyboard

1.202 Alpha Servers

AlphaServer 8200 Systems

Step 11—Expansion (System Cabinet and I/O Expansion Cabinet)

Step 11a

System Cabinet

System Cabinet includes one single-phase power supply.

Provides space for additional redundant (N+1) power supply.

BA656 Internal Storage Drawer included in system cabinet; provides space to accommodate four additional 3.5-inch narrow SCSI devices including one tape device.

Provides space for six BA350-JB or BA356-JB SCSI StorageWorks Shelves, three DWLPA-CA (PCI shelf mount boxes) or combination of StorageWorks and PCI shelves.

- For each DWLPA-CA placed in system cabinet, subtract two BA350-JB or BA356-JB shelves from maximum available.

Example: One DWLPA-CA in system cabinet allows for a maximum of four BA350-JB/BA356-JB shelves.

Shelf Mount Boxes Quantity

StorageWorks shelves (BA350-JB/BA356-JB) 6 maximum (see limits above)

PCI shelf mount box (DWLPA-CA) 3 maximum

Step 11b

I/O Expansion Cabinet

I/O expansion cabinet includes one single-phase power supply.

Provides space for additional redundant (N+1) power supply.

Maximum four I/O channels supported in each I/O expansion cabinet.

Space for 16 BA350-JB or BA356-JB SCSI StorageWorks Shelves, four DWLPA-CB (PCI Rack mount boxes) or combination StorageWorks and PCI shelves.

- For each DWLPA-CB placed in expansion cabinet, subtract two BA350-JB or BA356-JB shelves from maximum available.

Example: Three DWLPA-CB in expansion cabinet allows for a maximum of ten BA350-JB or BA356-JB shelves.

Shelf Mount Boxes Quantity

StorageWorks shelf (BA350-JB/BA356-JB) 16 maximum (see limits above)

PCI shelf mount box (DWLPA-CB) 4 maximum

H9B10-EA

I/O Expansion Cabinet—Single Phase power, maximum two per system

Note: See Step 2 for selection of proper power cord

 one per I/O expansion cabinet. If redundant supply (H7266-AD/AE) is ordered, power cord is not required.

Step 12

Power Options

Power options are available for AlphaServer 8200 system and expansion cabinets.

System cabinet and expansion cabinet includes one power supply (H7266-AA)—200-240 VAC input voltage, 48VDC,

2400 watt, output supply.

Power system supports N+1 power redundancy and battery backup capability.

If redundant power supply is ordered, power cord in Step 2 no longer required.

H7266-AD

H7266-AE

Single Phase 48V DC redundant power supply—60 Hz power connector, maximum one per cabinet

Single Phase 48V DC redundant power supply—50 Hz power connector, maximum one per cabinet

Note: See Specifications for information on which power supply to order.

Alpha Servers 1.203

AlphaServer 8200 Systems

Step 12a

Battery Backup Options

Optional battery backup requires addition of H7267-AA to each power supply in system cabinet and expansion cabinets.

Battery backup provides up to 5 minutes of capacity to power contents of system and expansion cabinets.

H7267-AA

H7239-AA

Battery Backup Option Kit

Includes batteries, charger board, installation manual for adding battery backup operation to one power supply (H7266-AA, H7266-AD, H7266-AE). Can be field installed.

Battery Pack replacement option—Includes two battery packs for replacement of batteries in power supply (H7266-AA, H7266-AD, H7266-AE). Field installed only.

Step 12b

Power Option for BA350/BA356 StorageWorks Shelves

Provides N+1 power for BA350-JB and BA356-JB StorageWorks shelves.

Occupies one slot in StorageWorks shelf.

BA35X-HG

48V DC 150W Redundant Power Supply for StorageWorks shelf; includes 48VDC jumper cable for connecting to first power supply in StorageWorks shelf.

Step 13—Software

Select user licenses and additional software as required. Note: Media and documentation required for first system on site.

Software Processor Code = Q

Digital UNIX Concurrent Use Licenses

Digital UNIX Concurrent Use licenses are not specific to a single system and can be moved from one system to another at user discretion.

QL-MT7AM-3B

QL-MT7AM-3C

QL-MT7AM-3D

QL-MT7AM-3E

QL-MT7AM-3F

QL-MT7AM-3G

QL-MT7AM-3H

QL-MT7AQ-AA

Digital UNIX Concurrent Use 1-user license

Digital UNIX Concurrent Use 2-user license

Digital UNIX Concurrent Use 4-user license

Digital UNIX Concurrent Use 8-user license

Digital UNIX Concurrent Use 16-user license

Digital UNIX Concurrent Use 32-user license

Digital UNIX Concurrent Use 64-user license

Digital UNIX Traditional unlimited user license

QL-MT5AQ-AA

QL-MT6AQ-AA

QL-MTJAQ-AA

QL-MTKAQ-AA

QB-05SAQ-AA

Digital UNIX developer's extension license

Digital UNIX server extension license

DECnet/OSI end-system license

DECnet/OSI extended function license

DECsafe Available Server license and documentation (Digital UNIX only). Media available on layered product CD-ROM. KZMSA or KZPSA adapter required.

Digital UNIX Media and Documentation

QA-MT4AA-H8

QA-MT4AA-GZ

QA-MT4AB-GZ

QA-MT5AA-GZ

QA-MT6AA-GZ

Digital UNIX media and on-line documentation (base system, complementary products) on CD-ROM

Digital UNIX full hardcopy documentation

Digital UNIX end user hardcopy documentation subkit

Digital UNIX developer’s extension hardcopy documentation subkit

Digital UNIX server extension hardcopy documentation subkit

1.204 Alpha Servers

AlphaServer 8200 Systems

Step 13—Software (continued)

OpenVMS Concurrent Use Licenses

OpenVMS Concurrent Use license provide the right to interactively use the operating system by the specified number of concurrent users on a designated OpenVMS system. OpenVMS Concurrent Use licenses can be moved from one system to another at user discretion and can be shared in a mixed OpenVMS VAX and OpenVMS Alpha cluster.

QL-MT3AA-3B

QL-MT3AA-3C

QL-MT3AA-3D

QL-MT3AA-3E

QL-MT3AA-3F

QL-MT3AA-3G

QL-MT3AA-3H

QL-MT3AA-3J

QL-MT3AA-3K

QL-MT2AQ-AA

OpenVMS Concurrent Use 1-user license

OpenVMS Concurrent Use 2-user license

OpenVMS Concurrent Use 4-user license

OpenVMS Concurrent Use 8-user license

OpenVMS Concurrent Use 16-user license

OpenVMS Concurrent Use 32-user license

OpenVMS Concurrent Use 64-user license

OpenVMS Concurrent Use 128-user license

OpenVMS Concurrent Use 256-user license

OpenVMS Traditional unlimited user license

QL-MTFAQ-AA

QL-MTHAQ-AA

DECnet/OSI end-system license

DECnet/OSI extended function license

OpenVMS Media and Documentation

QA-MT1AA-H8

QA-09SAA-GZ

QA-001AA-GZ

OpenVMS media and documentation on CD-ROM

OpenVMS base hardcopy documentation

OpenVMS full hardcopy documentation

Layered Products CD-ROM

QA-054AA-H8

QA-03XAA-H8

Layered products media and documentation for Digital UNIX

Layered products media and documentation for OpenVMS

Digital NAS Base Server 200 Software

Digital NAS Base Server 200 software included with base AlphaServer 8200 systems. Media available on layered product

CD-ROM.

Step 14—Hardware and Software Supplemental Support Services

Step 14a—Hardware and Software Supplemental Support Services (Americas and Asia Pacific Area only)

Hardware

Systems include one-year hardware warranty, on-site, same day, 4-hour response time.

Select optional Hardware Supplemental Support Services if required.

AlphaServer 8200

One CPU less than 2 GB memory

Two CPU less than 2 GB memory

FM-8U4HR-36

FM-8U512-36

FM-8U616-36

FM-8U724-36

FM-8D4HR-36

FM-8D512-36

FM-8D616-36

FM-8D724-36

FM-8U4HR-60

FM-8U512-60

FM-8U616-60

FM-8U724-60

FM-8D4HR-60

FM-8D512-60

FM-8D616-60

FM-8D724-60

Two CPU

2 GB memory

FM-8G4HR-36

FM-8G512-36

FM-8G616-36

FM-8G724-36

FM-8G4HR-60

FM-8G512-60

FM-8G616-60

FM-8G724-60

Years 1-3, 5 x 9, 4-hour response time

Years 1-3, 5 x 12, 4-hour response time

Years 1-3, 6 x 16, 4-hour response time

Years 1-3, 7 x 24, 4-hour response time

Years 1-5, 5 x 9, 4-hour response time

Years 1-5, 5 x 12, 4-hour response time

Years 1-5, 6 x 16, 4-hour response time

Years 1-5, 7 x 24, 4-hour response time

Alpha Servers 1.205

AlphaServer 8200 Systems

Step 14a—Hardware and Software Supplemental Support Services (Americas and Asia Pacific Area only)

(continued)

Software

Systems include 90-day Conformance to SPD and Telephone Advisory Support. Select optional Software Supplemental

Support Services, if required.

Software service upgrades for Digital UNIX and OpenVMS include advisory and remedial software support with new version license rights for operating system and Digital NAS Base Server 200 for the time period indicated.

AlphaServer 8200 One CPU Systems

FM-82UOS-12

FM-82UOS-36

FM-82UOS-60

12-month Software Supplemental Support for Digital UNIX one CPU systems

36-month Software Supplemental Support for Digital UNIX one CPU systems

60-month Software Supplemental Support for Digital UNIX one CPU systems

AlphaServer 8200 One CPU Systems

FM-82UVM-12

FM-82UVM-36

FM-82UVM-60

12-month Software Supplemental Support for OpenVMS one CPU systems

36-month Software Supplemental Support for OpenVMS one CPU systems

60-month Software Supplemental Support for OpenVMS one CPU systems

AlphaServer 8200 Two CPU Systems

FM-82DOS-12

FM-82DOS-36

FM-82DOS-60

12-month Software Supplemental Support for Digital UNIX two CPU systems

36-month Software Supplemental Support for Digital UNIX two CPU systems

60-month Software Supplemental Support for Digital UNIX two CPU systems

FM-82DVM-12

FM-82DVM-36

FM-82DVM-60

12-month Software Supplemental Support for OpenVMS two CPU systems

36-month Software Supplemental Support for OpenVMS two CPU systems

60-month Software Supplemental Support for OpenVMS two CPU systems

Step 14b—Hardware and Software Supplemental Support Services (Europe only)

Europe does not have specific part numbers for Hardware and Software Supplemental Support Services. Prices can be quoted using the Excelerator tool; contact MCS Sales in your country for information on Hardware and Software

Supplemental Support Services.

1.206 Alpha Servers

Digital AlphaServer 8200 Optional Controller Configuration Table

Optional Controller Configuration Table

With multiple adapters that provide the same interface available on different I/O buses (PCI, XMI, or Futurebus+), it is possible to exceed operating system limit on the number of ports supported for that interface. Follow these guidelines for maximum number of ports that each operating system supports. Fill in this table under the relevant area, add up number of controllers/ports available, and verify that operating system limits will not be exceeded. Do not exceed these values.

Option Name

SCSI Options

Included KFTIA-AA I/O module, one single-ended and three FWD

SCSI ports*

Additional KFTIA-AA I/O module, one single-ended and three

FWD SCSI ports

KZPSA-BB PCI fast wide differential SCSI adapter

A

Number of

Ports/Buses

4

4

1

Add column “C”—must be less than or equal to value listed under operating system to be used.

802.3/Ethernet Options

2

2

1

Included KFTIA-AA I/O module, two 802.3/Ethernet ports*

Additional KFTIA-AA I/O module, two 802.3/Ethernet ports

DE435-AA PCI 802.3/Ethernet controller

Add column “C”—must be less than or equal to value listed under operating system to be used.

FDDI Options

Included KFTIA-AA I/O module, optional FDDI daughter card installed (DEFPZ-AA/UA)*

Additional KFTIA-AA I/O module, optional FDDI daughter card installed (DEFPZ-AA/UA)

DEFPA-AA/DA/UA PCI FDDIcontroller, one port each

Add column “C”—must be less than or equal to value listed under operating system to be used.

1

1

1

B

Number of

Options

1

1

C

Total

Ports

(A * B)

4

2

Digital UNIX

Limit

OpenVMS

Limit

32

8

8

24

8

8

*Applies to Base Servers only.

EISA Bus IRQ Address Table

Configuration Rules and Information

EISA Bus IRQ address assignments are for Digital UNIX and OpenVMS systems only.

In some cases, the maximum number of each supported device is less than number of EISA bus addresses available; this is due to other limitations.

Only one device can occupy any given IRQ address; if multiples of a device are configured, each device occupies a separate address.

Match each device to one available address. (Note: With the table as a worksheet, fill in “0” for each device; fill in only one “0” per column).

Actual IRQ address assignment will be made by EISA Configuration Utility (ECU), which is run during system manufacture, or in the installed system if EISA bus is reconfigured.

Option

DNSES-AA

DW300-AA

CXI01-AA

CXI01-AD

5 7 8

EISA Bus IRQ Addresses

9 10 11 12 14 15

0

0

0

0

0

0

0

0

0

0

0

0

NA NA NA NA NA NA NA NA NA

NA NA NA NA NA NA NA NA NA

Maximum of Each Supported

OpenVMS

0

0

1

0

Digital UNIX

1

1

1

1

Table Codes:

0 = address is available for device

– = address not available for device

NA = Not Applicable

Alpha Servers 1.207

1.208 Alpha Servers

Front

Digital AlphaServer 8200 System Diagrams

System Cabinet

Rear

Processor

System Unit

StorageWorks or

PCI I/O Shelves*

StorageWorks

Shelves

Power Supplies

Front

Expansion Cabinet

StorageWorks

Shelves

Rear

BU-3480

StorageWorks or

PCI I/O Shelves*

CCL Panel

Power Supplies

* A PCI I/O shelf extends into the rear of the cabinet.

A StorageWorks shelf cannot be located behind a PCI shelf.

BU-3481

Specifications

Digital AlphaServer 8200 System Specifications

Physical Characteristics

Height

Width

Depth

Weight

Minimum configuration

Maximum configuration

Clearances

Front

Rear

Sides

Environmental

Temperature

Humidity

Altitude

Vibration

Heat dissipation

1

Operating

170.0 cm (67.0 in.)

60.0 cm (23.6 in.)

92.5 cm (36.4 in.)

Shipping

194.0 cm (76.25 in.)

91.5 cm (36.0 in.)

121.5 cm (47.9 in.)

318 kg (700 lb.)

591 kg ((1300 lb.)

Operating

363 kg (800 lb)

636 kg (1400 lb.)

Service

1.0 m (40 in.)

.75 m (29.5 in.)

0

1.5 m (59 in.)

1.0 m (40 in.)

0

Operating Non-Operating

10° to 35°C (50° to 95°F)

10% to 90%

0

2.4 km (0

8200 ft)

2

22 Hz @ 0.01"da minimum

Minimally configured system

1

(system cabinet)

3200 Btu/hr, 930 W

40° to 66°C (

40° to 151°F)

10% to 95%

9,100 m (30,000 ft)

22

500 Hz @ 0.25g max.

Fully configured system

2

(system cabinet)

9100 Btu/hr, 2647 W

Fully configured system

3

(system cabinet with two

I/O expansion cabinets)

21,300 Btu/hr, 6234 W

Regulatory

Agency approvals

Reviewed to

UL Listed to UL1950

CSA Certified to CAN/C22.2 No. 950-M89

FCC Part 15 (Class A)

CE Declaration #1259

EN 60950/A1, Jan. 1993, European Norm

AS/NZS 3260:1993, Australian/New Zealand Standard

EMKO-TSE{74-SEC}Summary of Nordic Deviations

IEC950, 2nd Ed., 2nd Amend.

US/Canada/Japan Europe/AP Power Requirements

4

Nominal AC input line voltage

Frequency range

Phases

Maximum input current

Surge current

Rating

Power cord part number

Power cord length

Power cap (system)

Receptacle

202-240 (208) V Japan (202) V

50

60 Hz

Single-phase line-to-line

or line-to-neutral

16 A rms

80 A peak

16 A

BN23H-4E

4.5 meters (15 feet)

DEC 12-16886-00

NEMA L6-30P

NEMA L6-30R

202-240 (240) V

50

60 Hz

Single-phase line-to-line

or line-to-neutral

16 A rms

80 A peak

16 A

BN20P-4E

4.5 meters (15 feet)

DEC 12-30333-03

IEC 309 (32A)

5

2 Pole/3-Wire (220-240V)

BC26E PCS/PDS/PDU/UPS cable

1 Minimally configured system contains one power supply, one CPU module, one memory module, one System

I/O module, one CD-ROM, and one RZ28 disk drive.

2 Fully configured system contains two power supplies, one CPU module, two memory modules, two System I/O modules, one CD-ROM, 16 RZ28 drives, two PCI shelves, and two StorageWorks shelves.

3 Fully configured system and two expansion cabinets consists of the above “fully configured system” and two expansion cabinets which each contain one PCI shelf , 14 StorageWorks shelves, and 84 RZ28 disk drives.

4 Power system provides unity power factor which allows full utilization of the input line current (Watts = VA).

5 Receptacle type is Hubbell 332R6 or equivalent.

Alpha Servers 1.209

Digital AlphaServer 8200 System Specifications

Recommended On-Line Power Protection/UPS Solutions for AlphaServer 8200 systems

For complete protection, UPS products should be used with data line surge protectors

4N-GA249-AB (2 wire modem),

4N-GA249-CA (10BaseT), 4N-GA510-BF (ThinWire). See TVSS section of Environmental Products Chapter.

System Storage UPS Model

AlphaServer 8200

(Single phase)

None

4N-AEAAJ-CL (60 Hz)

4N-AEAAJ-CU (50 Hz)

Receptacle Module for Plug-in Cconnection

60 Hz 50 Hz

Included

Hardwired

SW500 or

Expansion Cabinet

4N-AEAAL-BA 4N-AEACK-BN

Hardwired

SW800

4N-AEAAN-BA (60 Hz)

4N-AEAAN-BE (50 Hz)

4N-AEACM-BN

Hardwired

UPS Models

4N-AEAAJ-CL

4N-AEAAJ-CU

4N-AEAAL-BA

4N-AEAAN-BA

4N-AEAAN-BE

Prestige 6kVA (4kW), single phase, 60 Hz, 208V-120/208V, 6 ft. cord with L6-30P and (2) L6-30R, (8) 5-15R receptacles. Modular hot-swap design with 7 minutes battery at full load, extendable plug and play batteries and receptacle provisions. Unit includes 3 year hot swap warranty. Substitue -CT for 240V-240/120V operation.

Prestige 6kVA (4kW) 50 Hz package, single phase, 50/60 Hz, 200-240V in and out, selectable; hardwired input/output.

PUPS plus 10kVA (7kW), single-phase, 50/60Hz, 176-276V in, 200-240V out, 9 minutes battery at full load; hardwired with optional plug-in output receptacle modules.

PUPS plus 15kVA (7kW), three-phase, 50/60Hz, 176-256V in, 200-240V out, 10 minutes battery at full load; hardwired with optional plug-in output receptacle modules.

PUPS plus 15kVA (7kW), three-phase, 50/60Hz, International model rated 380/415V in, 380/415/220V out; hardwired input/output.

Options

4N-AEACM-BN

4N-AEACM-BK

4N-AEACH-HD

PUPS plus 15kVA receptacle module (3) L6-30R, (3) 5-20R, (2) L5-20R

PUPS plus 15kVA receptacle module (2) L21-30R, (3) 5-20R

Mobile module stacker for Prestige 6kVA models (includes siesmic supports)

UPS Monitoring and Unattended Shutdown Software (for above UPS systems only)

Includes cables, media and documentation.

UPS System

Prestige UPS

PUPS plus UPS

Network Management or mult shutdown*

Digital UNIX

4N-AEAES-AK

4N-AEAES-AK

4N-AEAES-BK

OpenVMS

4N-AEAES-EM

4N-AEAES-FM

Call for information

*Requires Connect-UPS Network Adapter (SNMP compatible) - for Digital UNIX systems, suffixes denote twisted pair/ThinWire

4N-AEAEO-DA/DC for 60Hz applications

4N-AEAEO-DE/DD for 50Hz applications

1.210 Alpha Servers

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement