Becker SunWindControl SWC411A Wall-mounted Transmitter Assembly and Operating Instructions
Below you will find brief information for Wall-mounted Transmitter SunWindControl SWC411A. The SWC411A is a wall-mounted transmitter that can be used to control one or more sun protection systems. It features a manual mode for direct control and an automatic mode for programmed sun and wind control. The device is equipped with a sun threshold control switch to adjust the sun intensity level for automatic extension of the sun protection system and a wind threshold control switch to set the wind speed level for automatic retraction.
PDF
Download
Document
Advertisement
Advertisement
Centronic SunWindControl SWC411A de Montage- und Betriebsanleitung Wandsender für Sonnen-Wind-Steuerung Wichtige Informationen für: • den Monteur / • die Elektrofachkraft / • den Benutzer Bitte entsprechend weiterleiten! Diese Anleitung ist vom Benutzer aufzubewahren. en Assembly and Operating Instructions Wall-mounted transmitter for sun and wind control Important information for: • Fitters / • Electricians / • Users Please forward accordingly! These instructions must be kept for future reference. Becker-Antriebe GmbH 35764 Sinn/Germany www.becker-antriebe.com Inhaltsverzeichnis Allgemeines............................................................................................... 4 Gewährleistung.......................................................................................... 4 Sicherheitshinweise................................................................................... 4 Bestimmungsgemäße Verwendung............................................................. 5 Anzeigen und Tastenerklärung................................................................... 6 Funktionserklärung.................................................................................... 6 Werkseinstellung........................................................................................ 8 Einlernen des Funks................................................................................... 9 Montage Wandhalterung...........................................................................10 Batteriewechsel........................................................................................10 Reinigung................................................................................................. 11 Technische Daten..................................................................................... 11 Was tun wenn ... ?.....................................................................................12 2 Contents General....................................................................................................14 Warranty...................................................................................................14 Safety tips................................................................................................14 Intended use............................................................................................15 Displays and pushbuttons..........................................................................16 Functions.................................................................................................16 Factory setting..........................................................................................18 Programming the remote control................................................................19 Installing the wall mount........................................................................... 20 Changing the battery................................................................................ 20 Cleaning...................................................................................................21 Technical data..........................................................................................21 What to do if ...?....................................................................................... 22 de en 3 Montage- und Betriebsanleitung Allgemeines Mit dem SWC411A können Sie eine oder mehrere Sonnenschutzanlagen steuern und Schwellwerte für Sonnenschutz und Windüberwachung mit der beiliegenden Einstellhilfe einstellen. Eine einfache Bedienung zeichnet dieses Gerät aus. Gewährleistung Bauliche Veränderungen und unsachgemäße Installationen entgegen dieser Anleitung und unseren sonstigen Hinweisen können zu ernsthaften Verletzungen von Körper und Gesundheit der Benutzer, z.B. Quetschungen, führen, so dass bauliche Veränderungen nur nach Absprache mit uns und unserer Zustimmung erfolgen dürfen und unsere Hinweise, insbesondere in der vorliegenden Montage- und Betriebsanleitung, unbedingt zu beachten sind. Eine Weiterverarbeitung der Produkte entgegen deren bestimmungsgemäßen Verwendung ist nicht zulässig. Endproduktehersteller und Installateur haben darauf zu achten, dass bei Verwendung unserer Produkte alle, insbesondere hinsichtlich Herstellung des Endproduktes, Installation und Kundenberatung, erforderlichen gesetzlichen und behördlichen Vorschriften, insbesondere die einschlägigen aktuellen EMV-Vorschriften, beachtet und eingehalten werden. Sicherheitshinweise Vorsicht Bitte bewahren Sie die Anleitung auf! • • • • • • Nur in trockenen Räumen verwenden. Verwenden Sie nur unveränderte Becker Originalteile. Halten Sie Personen aus dem Fahrbereich der Anlagen fern. Halten Sie Kinder von Steuerungen fern. Beachten Sie Ihre landesspezifischen Bestimmungen. Verbrauchte Batterien fachgerecht entsorgen. Batterien nur durch identischen Typ (LR 03; AAA) ersetzen. • Wird die Anlage durch einen oder mehrere Sender gesteuert, muss der Fahrbereich der Anlage während des Betriebes einsehbar sein. • Gerät enthält verschluckbare Kleinteile. 4 Bestimmungsgemäße Verwendung Der SWC411A darf nur für die Ansteuerung von Sonnenschutzanlagen verwendet werden. • Bitte beachten Sie, dass Funkanlagen nicht in Bereichen mit erhöhtem Störungsrisiko betrieben werden dürfen (z.B. Krankenhäuser, Flughäfen). • Die Fernsteuerung ist nur für Geräte und Anlagen zulässig, bei denen eine Funktionsstörung im Handsender oder Empfänger keine Gefahr für Personen, Tiere oder Sachen ergibt oder dieses Risiko durch andere Sicherheitseinrichtungen abgedeckt ist. • Der Betreiber genießt keinerlei Schutz vor Störungen durch andere Fernmeldeanlagen und Endeinrichtungen (z.B. auch durch Funkanlagen, die ordnungsgemäß im gleichen Frequenzbereich betrieben werden). • Funkempfänger nur mit vom Hersteller zugelassenen Geräten und Anlagen verbinden. Achtung Die Schwellwertregler sind mit einer sicherheitsrelevanten Funktion versehen. Eine falsche Einstellung der Schwellwerte kann zu Schäden an der Sonnenschutzanlage führen. Daher sollte die Einstellung der Schwellwerte zur Sicherheit Ihrer Sonnenschutzanlage nur von einem Fachhändler oder unter dessen Anleitung erfolgen. Hinweis Achten Sie darauf das die Steuerung nicht im Bereich metallischer Flächen oder magnetischer Felder installiert und betrieben wird. Funkanlagen, die auf der gleichen Frequenz senden, können zur Störung des Empfangs führen. Es ist zu beachten, dass die Reichweite des Funksignals durch den Gesetzgeber und den baulichen Maßnahmen begrenzt ist. 5 de en Montage- und Betriebsanleitung Anzeigen und Tastenerklärung Reset SWC411 - +- + EINFAHR-Taste STOPP-Taste AUSFAHR-Taste Windschwellwertregler Sonnenschwellwertregler Reset-Taste Sendekontrollleuchte Hand / Automatik Schiebeschalter Einstellhilfe Batteriefach Einlerntaste Funktionserklärung Hand/Automatik Schiebeschalter In der Schiebeschalterstellung „H“ werden manuelle Fahrbefehle (z.B.: AUF, STOP, AB per Tastendruck) und Notsignale (z.B.: Windalarm bei vorhandenem Windsensor) ausgeführt. In der Schiebeschalterstellung „S“ werden automatische Fahrbefehle ausgeführt (z.B. Sonnenschutzfunktion, ...). Wird im Automatikbetrieb ein manueller Fahrbefehl ausgeführt, werden die automatischen Sonnenschutz-Funktionen unterbrochen. Diese aktivieren sich wieder selbständig bei Über-/Unterschreiten der eingestellten Schwellwerte, nach erfolgter Einfahrt oder durch Wechsel des Schiebeschalters von „S“ auf „H“ und wieder zurück auf „S“. 6 Sendekontrollleuchte Ein Funksignal wird durch das Aufleuchten der Sendekontrollleuchte signalisiert. Lässt die Leistung der Batterie nach, blinkt die Sendekontrollleuchte beim Senden. Die Sendeleistung bzw. Funkreichweite wird durch Abnahme der Batterieleistung reduziert. Leuchtet die Sendekontrollleuchte bei Tastendruck nicht mehr, müssen die Batterien gewechselt werden. Kanal Der Kanal eines Handsenders kann in einen oder mehrere Empfänger eingelernt werden. Die Ansteuerung eines Empfängers ist ein Individualbefehl, die mehrerer Empfänger ein Gruppenbefehl. Windschwellwertregler Mit diesem Regler stellen Sie die Windschwellwerte ein (ca. 2m/s bis 22 m/s). Der Windschwellwert lässt sich in 11 Stufen einstellen. Beim langsamen Drehen des Reglers werden Ihnen die Stufen durch das Klacken des Rohrantriebes angezeigt. - Linksanschlag = Stufe 1, Einfahren bei wenig Wind de + Rechtsanschlag = Stufe 11, Einfahren bei sehr starken Wind en Bei Änderung der Schwellwerte werden diese sofort übertragen. Hinweis Achten Sie darauf, dass beim Einstellen des Schwellwertes keine Taste gedrückt ist. Wird der eingestellte Windschwellwert überschritten, fährt die Sonnenschutzanlage ein und bleibt geschlossen. Ein Ausfahren der Sonnenschutzanlage ist erst nach ca. 15 Minuten dauerhaft unterschrittenem Windschwellwert möglich. 7 Montage- und Betriebsanleitung Sonnenschwellwertregler Mit diesem Regler stellen Sie die Sonnenschwellwerte ein (ca. 2 KLux bis 100 KLux). Der Sonnenschwellwert lässt sich in 15 Stufen einstellen. Beim langsamen Drehen des Reglers werden Ihnen die Stufen durch das Klacken des Rohrantriebes angezeigt. - Linksanschlag = Stufe 1, Ausfahren bei wenig Sonne + Rechtsanschlag = Stufe 15, Ausfahren bei voller Sonne Bei Änderung der Schwellwerte werden diese sofort übertragen. Hinweis Achten Sie darauf, dass beim Einstellen des Schwellwertes keine Taste gedrückt ist. Wird der eingestellte Sonnenschwellwert überschritten, fährt die Sonnenschutzanlage nach ca. 3 Minuten aus. Ein automatisches Einfahren der Sonnenschutzanlage erfolgt nach ca. 15 Minuten dauerhaft unterschrittenem Sonnenschwellwert. TEST-Modus Der TEST-Modus wird aktiviert durch Verstellen eines Schwellwertes. Dieser wird automatisch beendet nach ca. 15 Minuten oder sofort durch Betätigen des Schiebeschalters. Im TEST-Modus werden die Zeiten der Beschattungsfunktion und der Windüberwachung verkürzt. Werkseinstellung Sonnenschwellwert: Mittelstellung (ca. 35KLux) Windschwellwert: Linksanschlag (ca. 2 m/s) 8 Einlernen des Funks Vorsicht Überprüfen Sie vor dem Einlernen des Funks, ob die Schwellwertregler in der Werkseinstellung stehen. Achten Sie darauf das Sie sich beim Einlernen des Funks nicht im Fahrbereich der Sonnenschutzanlage befinden. 1) Mastersender einlernen a) Empfänger in Lernbereitschaft bringen Hinweis Unter Mastersender versteht man den ersten in einen Empfänger eingelernten Sender. Im Gegensatz zu weiteren hinzugelernten Sendern ermöglicht der Mastersender u.a. das Einstellen der Endlagen (bei Antrieben mit integr. Funkempfänger) und das Hinzulernen oder Löschen weiterer Sender. Mastersender können alle Sender sein, die eine separate AUF-, STOPP-, AB-Taste und eine Einlerntaste haben. Beachten Sie die Montage- und Betriebsanleitung des Empfängers. • Schalten Sie die Spannungsversorgung des Empfängers aus und nach 5 Sekunden wieder ein. oder • Betätigen Sie die Lerntaste bzw. den Funkschalter des Empfängers. Der Empfänger befindet sich nun für 3 Minuten in Lernbereitschaft. b) Mastersender einlernen Drücken Sie die Einlerntaste innerhalb der Lernbereitschaft, bis der Empfänger das erfolgreiche Einlernen quittiert. Damit ist der Einlernvorgang beendet. 2) weitere Sender einlernen a)Drücken Sie die Einlerntaste des Mastersenders, bis der Empfänger quittiert. b)Drücken Sie nun die Einlerntaste des neuen Senders, bis der Empfänger quittiert. c)Jetzt drücken Sie die Einlerntaste des neu einzulernenden Senders noch einmal. Der Empfänger quittiert das erfolgreiche Einlernen. Die maximale Funkreichweite beträgt am und im Gebäude bis zu 15 m und im freien Feld bis zu 150 m. 9 de en Montage- und Betriebsanleitung Montage Wandhalterung 60,2 22,5 47 • Prüfen Sie vor der Montage an der gewünschten Montageposition die einwandfreie Funktion von Sender und Empfänger. • Befestigen Sie die Halterung mit den zwei beigelegten Schrauben an der Wand. 42,9 Batteriewechsel 1.Entnehmen Sie die Batterien. 2.Legen Sie die neuen Batterien lagerichtig ein. 10 Reinigung Reinigen Sie das Gerät nur mit einem feuchten Tuch. Verwenden Sie kein Reinigungsmittel, da dieses den Kunststoff angreifen kann. Technische Daten Nennspannung Batterietyp Schutzart Zulässige Umgebungstemperatur Funkfrequenz 3 V DC LR 03 (AAA) IP 20 -10 bis +55 °C 915,3 MHz de en 11 Montage- und Betriebsanleitung Was tun wenn ... ? Störung Antrieb läuft nicht, Sendekontrollleuchte bleibt aus. Antrieb läuft nicht, Sendekontrollleuchte leuchtet. Sendekontrollleuchte blinkt. Die automatischen Fahrbefehle werden nicht ausgeführt. Anlage fährt nicht automatisch aus bei Schiebeschalterstellung “S“. Anlage fährt nicht manuell aus bei Schiebeschalterstellung “H“ oder “S“. 12 Ursache 1.Batterien sind leer. Abhilfe 1.Neue Batterien einlegen. 2.Batterien richtig einlegen. 1.Entfernung zum Empfänger verringern. 2.SWC411A einlernen. 2.Batterien sind falsch eingelegt. 1.Empfänger außerhalb der Funkreichweite. 2.SWC411A ist nicht im Empfänger eingelernt. Batterien sind schwach. Neue Batterien einlegen. 1.Schiebeschalter steht auf “H“. 2.Die automatische Sonnenschutz-Funktion wurde durch einen manuellen Fahrbefehl unterbrochen. 1.Sonnenschwellwert ist unterschritten. 2.Windschwellwert ist überschritten. Windschwellwert ist überschritten. 1.Schiebeschalter auf “S“ stellen. 2.Schiebeschalter von “S“ auf “H“ und wieder auf “S“ stellen. 1.Sonnenschwellwert anpassen. 2.Abflauen des Windes abwarten. Abflauen des Windes abwarten. de en 13 Assembly and Operating Instructions General The SWC411A can be used to operate one or more sun protection systems and to set threshold values for sun protection and wind control with the help of the setting aid provided. This device is excellent because it is so easy to operate. Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries, e.g. crushing of limbs. Therefore, structural modifications should only be carried out with our prior approval and in accordance with our instructions, particularly the information contained in these Assembly and Operating Instructions. Any further processing of the products which does not comply with their intended use is not permitted. The end product manufacturer and fitter have to ensure that all the current statutory, official regulations and, in particular, EMC regulations are adhered to during utilisation of our products, especially with regard to end product assembly, installation and customer advice. Safety tips Danger Please keep the instructions in a safe place! • Use in dry rooms only. • Use unmodified Becker original parts only. • Keep persons away from the system guide track. • Keep children away from controls. • Please comply with national stipulations. • Dispose of used batteries properly. Replace batteries by an identical type (LR 03; AAA) only. • If the system is controlled using one or several transmitters, the system guide track must be visible during operation. • Please refer to the specifications given in the operating instructions for the sun protection system • The equipment contains small parts that could be swallowed. 14 Intended use The SWC411A may be used to operate sun protection systems only. • Please note that radio sets cannot be operated in areas with increased risk of interference (e.g. hospitals, airports). • The remote control is only permitted for equipment and systems with which a malfunction in the hand-held transmitter or receiver does not present a risk to persons, animals or objects, or this risk is covered by other safety devices. • The operator does not enjoy any protection from disturbances by other remote signalling equipment and terminal equipment (for example, also by radio sets operated in the same frequency range in accordance with regulations). • Use radio receivers in conjunction only with devices and systems permitted by the manufacturer. Attention These controllers are equipped with a special safety-relevant function. Incorrect setting of the threshold values, in connection with this function, can result in damage to the sun protection system. Therefore, setting of the threshold values, which ensure safe operation of the sun protection system, should only be carried out by specialists or under their instructions. Note Ensure that the controls are not installed and operated in the vicinity of metal surfaces or magnetic fields. Radio sets transmitting at the same frequency could interfere with reception. It should be noted that the range of the radio signal is restricted by legislation and constructional measures. 15 de en Assembly and Operating Instructions Displays and pushbuttons RETRACT button STOP pushbutton EXTEND button Wind threshold control switch Reset SWC411 - +- Sun threshold control switch + RESET-button Transmission control light MAN / AUTO Sliding Switch Setting aid Battery compartment Programming pushbutton Functions MAN/AUTO Sliding Switch When the sliding switch is set to H, manual control commands (e.g.: UP, STOP, DOWN pushbutton commands) are executed and an alarm signal (e.g.: wind alarm if wind sensor is integrated) given. When the sliding switch is set to S, automatic control commands are executed (e.g. sun protection function, ...). The automatic sun protection functions are interrupted if a manual operation is executed during automatic mode. These functions are re-activated automatically when the programmed threshold values are exceeded or undercut after retraction or via switching the slide switch from “S” to “H” and back to “S”. 16 Transmission control light A radio signal is indicated by the transmission control light being lit. If the battery starts running out, the transmission control light flashes during transmission. The transmitter power and/or radio range is reduced when the battery is running low. If the transmission control light is no longer lit when the pushbutton is pressed, the batteries must be changed. Channel The channel of a handheld transmitter can be programmed into one or several receivers. One or several receivers are controlled via an individual or group command respectively. Wind threshold control switch This control switch allows you to set the wind threshold values (approx. 2m/s to 22 m/s). The wind threshold value can be set to 11 different levels. If you turn the control switch slowly, the tubular drive makes a clacking sound for each level. - Left limit stop = Level 1: retract when wind speed is low de + Right limit stop = Level 11: retract when wind speed is high en If the threshold values are changed, these are adopted immediately. Note Please ensure that no buttons are pressed when setting the threshold value. If the wind speed rises above the preset wind threshold, the sun protection system is retracted and remains closed. The sun protection system is extended again if the wind speed remains below the preset wind threshold for approx. 15 minutes. 17 Assembly and Operating Instructions Sun threshold control switch This control switch allows you to set the sun threshold values (approx. 2KLux to 100KLux). The sun threshold value can be set to 15 different levels. If you turn the control switch slowly, the tubular drive makes a clacking sound for each level. - Left limit stop = Level 1: extend when sun intensity is low + Right limit stop = Level 15: extend when sun intensity is high If the threshold values are changed, these are adopted immediately. Note Please ensure that no buttons are pressed when setting the threshold value. If the sun intensity rises above the preset sun threshold, the sun protection system is extended after approximately 3 minutes. The sun protection system is retracted again automatically if the sun intensity remains below the sun threshold for approx. 15 minutes. TEST mode The TEST mode is activated by adjusting the threshold value. This mode will automatically end after approx. 15 minutes. Alternatively, the sliding switch can be used to deactivate the test mode immediately. In the TEST mode, the times for the sunshade function and wind control are reduced. Factory setting Sun threshold value: Intermediate position (35KLux) Wind threshold value: Left limit stop (2 m/s) Intermediate position 18 Programming the remote control Caution Before programming the transmitter, please check whether the threshold control switches are set to the factory setting. When programming the transmitter, ensure that you are not located in the operating area of the sun protection system. 1) Learning the master transmitter a) Put receiver into learn mode Note The master transmitter is the very first transmitter programmed on a receiver. In contrast to subsequently programmed transmitters, the master transmitter enables, among other things, the setting of limit positions (for drives with integr. radio receiver) and the programming or deleting of further transmitters.Any transmitter which has a separate UP, STOP, DOWN button and a programming button can be a master transmitter. Always follow the installation and operating instructions of the receiver. • Switch off the receiver’s power supply and reconnect after 5 seconds. or • Activate the “Learn” key or the radio-controlled receiver switch. The receiver will then be in “Learn” mode for 3 minutes. b) Learn master transmitter When the receiver is in “Learn” mode, the learn button is to be pressed until the receiver indicates that the learn process has been successfully completed. The learn process is now complete. 2) Learning additional transmitters a)Press the learn button of the master transmitter until acknowledgement is given by the receiver. b)Now press the learn button of the new transmitter until acknowledgement is given by the receiver c)Then press the learn button of the new transmitter to be learnt once again. The receiver will indicate when the learn process has been successfully completed. The maximum radio range is up to 15 m outside and inside the building and up to 150 m in the open. 19 de en Assembly and Operating Instructions Installing the wall mount • Before installing in the position required, check that the transmitter and receiver are functioning properly. • Fix the mount to the wall with the two screws provided. 60,2 22,5 47 42,9 Changing the battery 1.Take out the batteries. 2.Insert the new batteries in the correct position. 20 Cleaning Clean the device with a damp cloth only. Do not use a cleansing agent since this could damage the plastic. Technical data Nominal voltage Type of battery Protection class Permissible surrounding temperature Radio frequency 3 V DC LR 03 (AAA) IP 20 -10 to +55 °C 915.3 MHz de en 21 Assembly and Operating Instructions What to do if ...? Problem Drive is not functioning, transmission control light is not lit. Drive is not functioning; transmission control light is illuminated. Cause 1.Batteries are dead. 2.Batteries are incorrectly inserted. 1.Receiver outside the radio range. 2.SWC411A is not programmed in the receiver. Batteries are running out. Remedy 1.Insert new batteries. 2.Insert batteries correctly. 1.Reduce distance to the receiver. 2.Programme SWC411A. 1.Sliding switch not in the “H“ position. 2.The automatic sun protection function was interrupted by a manual command. 1.Sunlight intensity is The system is not below the threshold extended automatically value. when the sliding switch 2.Wind speed exceeds is set to “S“. threshold value. Wind speed exceeds The system does not threshold value. extended manually when the sliding switch is set to “H“ or “S“. 1.Set sliding switch to the “S“ position. 2.Turn the sliding switch from “S” to “H” and back to “S”. Transmission control light is flashing. Automatic control commands are not executed. 22 Insert new batteries. 1.Adjust sun threshold value. 2.Wait until wind abates. Wait until wind abates. de en 23 4033 630 092 0 10/10 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Manual and Automatic Control
- Sun and Wind Threshold Control
- Easy to Use
- Wall-Mountable
Frequently asked questions
The transmitter can be programmed into one or several receivers. You will need to put the receiver into learn mode and then press the learn button on the transmitter. The specific instructions can be found in the manual.
The transmitter has two modes of operation: Manual and Automatic. In Manual mode, you can directly control the sun protection system using the up, down, and stop buttons. In Automatic mode, the system will automatically extend or retract based on the sun and wind thresholds that you set.
To change the batteries, remove the old batteries and insert the new ones in the correct position.