GENEQ inc. - Geo
GENEQ inc.
SXPad 800H Controller
USER MANUAL
Table of Contents
Chapter 1 Product Introduction ...................... 1
1.1 Front Components ............................. 1
1.1.1 Keypad ................................ . 3
1.2 Back Components .............................. 4
1.3 Bottom Components ............................ 5
Chapter 2 Basic Skills ............................. 6
2.1 Turning on、Suspending、Turning Off、Resetting ... 6
2.1.1 Turning on .............................. 6
2.1.2 Suspending .............................. 6
2.1.3 Turning off ............................. 6
2.1.4 Resetting ............................... 7
2.1.4.1 Performing a Hard Reset .............. 7
2.2 Pull the Stylus out and in .................... 7
2.3 Installing、Uninstalling the SIM、TF Card and Battery
................................ .............. 7
2.4 Charging the Battery.......................... 7
2.5 Fitting the Hand Strap ........................ 8
Chapter 3
Connecting and Synchronizing with Your Computer
................................ ................. 9
3.1 Installing Connection Management Software ........ 9
3.1.1 Installing the Windows Mobile Device Center .. 9
3.1.2 Installing ActiveSync ................... 10
3.2 Connecting and Synchronizing With Your Computer . 10
3.2.1 Managing the Connection and Synchronization Using
the Windows Mobile Device Center ............... 10
3.2.2 Managing the Connection and Synchronization Using
the ActiveSync............................... 13
3.2.3 Connecting With U Disk Mode .............. 15
3.2.4 OTG Connection ......................... 17
Chapter 4 Brief Description of the Operating System ... 18
4.1 System Main Interface and the Start Menu ....... 18
4.2 Status Indicators ........................... 19
4.2.1 Battery Status Indicators ................ 20
4.2.2 Speaker Status Indicators ................ 20
4.2.3 Network and Modem Status Indicators ....... 20
4.3 Pre-installed Programs ....................... 21
4.4 Interacting With the Device................... 22
4.5 Entering Information......................... 22
4.5.1 Using the On-screen Keyboard ............. 23
4.5.2 Drawing and Writing on the Screen Directly . 23
4.5.3 Recording a Message ..................... 24
4.5.4 Camera (Select Models Only) .............. 24
4.5.4.1 Taking Pictures .................... 24
4.5.4.2 Recording Video Clips ............... 26
4.6 Personal Settings ........................... 28
4.6.1 Buttons ............................... 28
4.6.2 Home ................................ .. 28
4.6.2.1 Appearance ......................... 29
4.6.2.2 Items ............................. 29
4.6.2.3 Set Date and time ................... 30
4.6.3 Screen Lock ............................ 31
4.6.4 Set Passwords .......................... 31
4.6.5 Power ................................ . 32
4.6.6 Sounds and Notifications ................. 33
4.6.7 Screen ................................ 33
4.6.8 Backlight .............................. 34
4.6.9 Align Screen ........................... 35
4.7 GPRS Network Setting......................... 35
4.7.1 Add New GPRS Connecting .................. 35
4.8 Bluetooth Connecting......................... 37
4.9 Phone and Text Messages (Select Models Only) .... 38
4.9.1 Phone ................................ . 38
4.9.1.1 About Your Phone ................... 38
4.9.1.2 Making a Call ...................... 40
4.9.1.3 Responding to a Call ................ 42
4.9.1.4 Operations During a Call ............. 42
4.9.1.5 Using Call History .................. 44
4.9.1.6 Using Speed Dial ................... 45
4.9.1.7 Customizing Your Phone .............. 45
4.9.1.8 Additional Phone Operations .......... 46
4.9.2 Text Messages .......................... 47
4.9.2.1 Reading Text Messages ............... 47
4.9.2.2 Composing and Sending a Text Message .. 48
4.10 WIFI Connecting ............................ 48
4.10.1 Switching On or Off the Wi-Fi Radio ....... 48
4.10.2 Connecting to a Wireless Network ......... 48
Chapter 5 Software Operation ....................... 50
5.1 Installing Programs ......................... 50
5.2 Uninstalling Programs ........................ 50
Chapter 6 Troubleshooting and Maintenance ............ 51
6.1 Troubleshooting ............................. 51
6.2 Resetting Your Device ........................ 52
6.3 Caring for Your Device ....................... 52
Chapter 1 Product Introduction
This chapter mainly introduces you to the external components of your device.
1.1 Front Components
1
Ref
Component
Description
Flashes in red to indicate that your device is
①
being turned on.
When battery charging, Flashes in green to
Charge/Power on
Indicator
indicate battery charging is in progress.
Flashes in amber to indicate that the battery is
fully charged.
②
Flashes in green to indicate that the GPS
function is switched on.
GPS Indicator
Flashes in blue to indicate that the Bluetooth
Wireless
③
communication
indicator
④
Earpiece
⑤
Touch Screen
⑥
Keypad
⑦
Power Button
⑧
Microphone
function is on.
Flashes in green to indicate that the Phone
function is on.
Serves as the phone earpiece during a call.
Displays the output of your device and
responds to your tapping.
Includes keys for
numbers and
functions.
Turns on or off your device.
Records voices.
Serves as the mouthpiece during a call.
2
specific
1.1.1 Keypad
Ref
Component
Description
Numeric Keys
Enter numbers(majorly for models with the phone function)
Provide functions as indicated by the red icons when Fn lock is
on.
Moves up, down, left and right within the
screen or menu.
①
Alternative
Function Keys
Goes to the next input field.
Backspaces over one character when in a text
input field.
Increases the brightness level of the screen. It
cycles to the lowest level after reaching the
highest level.
②
③
④
Send Key
Dials or answers a call.
Left/Right Soft
Performs the command shown on the bottom left or right
Key
corner of the screen.
Switches on or off the alternative functions of the numeric keys.
Function Key
Fn lock is off by default. When it is switched on, the icon
shows in the navigation bar.
3
Starts the Camera program.
⑤
Camera Key
⑥
End Key
⑦
Serves as the shutter release button if the Camera program is
currently in use.
Ends or rejects a call (select models only).
Returns to the Today screen from another program.
Backspaces over one character when in a text input field.
⑧
Start Key
⑨
Action Key
Open the Start menu.
Confirms your selection by pressing, similar to the Enter key on
a keyboard.
1.2 Back Components
4
Chapter 2 Basic Skills
This chapter mainly introduces you to the basic operations of your device.
2.1 Turning on、Suspending、Turning Off、Resetting
2.1.1 Turning on
Press the Power Button and don not let go until the indicator color turns to green
from red. It’s about 33 seconds to turn on the product. Then the screen will appear
the device information and Windows icon in order.
2.1.2 Suspending
Press the power button one second when the device is on, let go, the device will be
suspended and the first indicator from the left color turns to amber.
If the device has already in use, the device suspends halfway (black screen),to
resume operation, press the power button. You will be back to where you left off.
CAUTION: The mobile phone indicator keeps on flashing when your device is
suspended. Any incoming call will resume your device.
2.1.3 Turning off
If you are not using your device, press and hold the power button for at least 3
seconds until the device appears a dialog box as shown in figure 1. Then click “OK”.
Figure 1
6
2.1.4 Resetting
If the device stops responding to the stylus or if it does not respond when you press
any of the keypad buttons, you may need to reset it by performing a hard reset.
2.1.4.1 Performing a Hard Reset
press both
and
buttons one minute at the same time,and then press
the power button to turn on your device.
2.2 Pull the Stylus out and in
Use the stylus to navigate and select objects on the screen.
Attach the stylus and your device with the tether. Pull the stylus out of the slot and
extend it for ease of use. Store it in the slot when not in use.
2.3 Installing、Uninstalling the SIM、TF Card and Battery
1. Lift the latch handle of the battery cover and turn it counterclockwise to the
unlock (vertical) position. Then, detach the cover from the device.
2. We can see two slots then, with the upper side one installing SIM card and the
bottom side one installing TF card. To install the SIM card, push the SIM card holder
right. With the SIM card’s chip side facing down put the card into the slot. Close the
holder then. The TF card installation is similar to the SIM card installation. To remove
the SIM card and TF card, push the holder and then take out the card.
3. To install the battery, attach the bottom side of the battery to the compartment at
an angle and then lower the upper side to engage the connector. Attach the bottom
side of the battery cover to the device at an angle, and then with the handle still in
the unlock (vertical) position, fit the latch handle into place. Secure the latch by
turning it clockwise to the lock (horizontal) position.
CAUTION: it’s easy to cause damage to the battery when installing the battery, if we
lower the upper side of the battery to engage the connector first in an angle and
then attach the bottom side of the battery to the compartment.
2.4 Charging the Battery
CAUTION
RISK OF EXPLOSION IF BATTERYIS REPLACED BY AN INCORRECT TYPE.
7
DISPOSE OF USED BATTERIES ACCORDING
The battery isn’t charging when factory. So we must charge the battery completely
before using it for the first time. Charging lasts for two and a half hours, the charger
has overcharge protection function.
CAUTION: For optimal performance of the lithium battery, take note of the following:
 Use the included AC adapter and charger only.
 There is no need to fully discharge the battery before charging. You can charge
the battery before it is discharged.
 Do not charge the battery where the temperature is high(higher than 50℃) or
low(less than 0℃).
 If you will not use the product for a long period of time, be sure to fully charge
the battery at least once every two weeks, over discharge of the battery can
affect the charging performance.
2.5 Fitting the Hand Strap
Align the upper hand strap bracket with the two mounting holes behind the device
and then use a screwdriver to tighten the screws. The other side is fixed to the hand
strap holders at the bottom of the device. We can see it after the installation is
complete as shown in figure 2.
8
Figure 2
Chapter 3 Connecting and Synchronizing with Your Computer
3.1 Installing Connection Management Software
To install software onto a device powered by the Windows Mobile operating system
or to copy files between your device and a PC you must connect the device to a PC. If
the computer is running:
• Windows 7 or Windows Vista operating system, use the Windows Mobile Device
Center (WMDC) to manage the connection.
• Windows XP or 2000 operating system, use ActiveSync to manage the connection.
CAUTION: You must install the Windows Mobile Device Center or ActiveSync
technology onto the computer before you connect the handheld.
3.1.1 Installing the Windows Mobile Device Center
The Windows 7 and the Windows Vista operating system include a basic connectivity
driver for devices powered by a Windows Mobile operating system. This driver allows
9
you to transfer files from the device to an office computer.
To install software onto a device powered by a Windows Mobile operating system,
you must install Windows Mobile Device Center 6.5 onto a PC.
3.1.2 Installing ActiveSync
Search the ActiveSync 4.5 version to download. Alternatively, visit
http://www.microsoft.com/en-us/download/details.aspx?id=15 to download the
latest version from the Microsoft website.
3.2 Connecting and Synchronizing With Your Computer
To connect the device to a PC:
1. Make sure that the device and the PC are switched on.
2. Make sure you have installed the appropriate connection management software
onto the PC.
3. To form a connection, do one of the following:
① Use the device's integrated Bluetooth radio to establish a wireless serial link to a
Bluetooth-enabled computer.
② Use a USB connection: Plug the USB cable into the USB port on the device. Plug
the other end of the USB cable into a USB port on the PC.
3.2.1 Managing the Connection and Synchronization Using the Windows Mobile
Device Center
Connect the device to the PC. It will appear a dialog box shown as in figure 3 if the
device successfully connects to the PC.
10
Figure 3
CAUTION: If the device doesn’t establish a connection automatically, check whether
the connection is enabled in the Windows Mobile Device Center software and on the
device.
Click “connect without setting up your device” shown as in figure 4.
Figure 4
11
Click “File Management”. Appear a drop-down menu shown as in figure 5.
Figure 5
Click “Browse the contents of your device” shown as in figure 6.
12
Figure 6
Open the data of the corresponding letter of the disk, select the files in the desired
path you want to realize uploading and downloading files.
3.2.2 Managing the Connection and Synchronization Using the ActiveSync
Connect your device and a computer, it will appear the dialog box shown as
“Microsoft Outlook”, tap “×” on the upper-right corner.
Tap “×” when it appear the dialog box on the upper-right corner shown as in figure 7.
Figure 7
When the Welcome to the Pocket PC sync setup wizard shown as in figure 8 appears,
tap “×” on the upper-right corner.
13
Figure 10
3.2.3 Connecting With U Disk Mode
When you have established connection between your device and your computer, the
U disk mode will complete before ActiveSync mode. Open “My computer” and then
you can see the letter of “Mobile Device” shown as in figure 11.
15
Figure 11
Open “Mobile Device”, you will enter the same operation interface as the ActiveSync
mode shown as in figure 12. The later procedure is the same as the ActiveSync.
16
Figure 12
CAUTION: please ensure the device has enough power during synchronously
transmitting data.
3.2.4 OTG Connection
Use OTG function connecting cord to connect the U disk or other USB mobile storage
devices to USB connector on the bottom of the device. Open File Explorer, tap the
pull-down box of my device, then you can see the letter of “Hard Disk”. You can
transform data between the hard disk and the device.
17
Chapter 4 Brief Description of the Operating System
4.1 System Main Interface and the Start Menu
Turn on the device by press the battery button for some time, then we can see the
home screen shown as figure 13.
Figure 13
Click the Windows icon
in the lower left corner of the home screen. We can
see the start menu shown as figure 14 where we can conduct basic settings and start
relevant procedures.
18
Figure 14
Press and hold the program icon until the icon bounce shown as figure 15, then drag
the icon to the location where you want shown as figure 16.
Figure 15
Figure 16
4.2 Status Indicators
The status indicators appear in the title bar at the top of the screen.
19
4.2.1 Battery Status Indicators
The battery status icon on the title bar of the Home screen or the Start screen shows
the status of the battery charge.
Icon
Description
Battery has full charge
Battery has high charge
Battery has medium charge
Battery has low charge
Battery
has
very
low
charge(20% or less)
Battery charging/use external
charge
4.2.2 Speaker Status Indicators
The battery status icon on the title bar of the Home screen or the Start screen shows
the status of the speaker.
Icon
Description
Speaker is on
Speaker is off
4.2.3 Network and Modem Status Indicators
The network and modem status icons on the title bar of the Home screen or the Start
screen show the status of each radio.
20
Icon
Description
Connected to ActiveSync or
the Windows Mobile Device
Center(WMDC)on a
computer
Connected to
Bluetooth-enabled computer
Wi-Fi radio is on
Maximum cellular modem
signal strength
Cellular modem is turned off
No cellular service
No SIM card
4.3 Pre-installed Programs
Programs that are pre-installed on the device are as follows:
Program
ActiveSync
Function
Synchronize information between the device and a
computer.
Alarms
Set alarms.
Text
Send, receive and organize text messages.
E-mail
Internet
Compose, send and receive E-mail messages.
Brows the world wide web.
Explorer
Calendar
Keep track of appointments and arrange meetings.
Contacts
Keep track of your friends and colleagues.
Windows Live
Windows
Media
Notes
Calculator
Access Windows Live services, including: E-mail, instant
messenger and Internet search.
Play Windows Media or MP3 audio and video files.
Create handwritten, typed or recorded notes.
Perform basic arithmetic functions.
21
Keep track of your tasks.
Tasks
Pictures &
Videos
Search Phone
Take, view, and edit pictures, or record and launch video
clips.
Search for a file or item stored on the device
4.4 Interacting With the Device
To interact with the handheld use the stylus or your finger to tap items on the touch
screen or to scroll up or down.
Action
Tap
Press and hold
Drag
Flick
Definition
Touch the screen once to open the items and select
options.
Press and hold an item to see a list of actions available for
that item. On the pop-up menu that appears, tap the
action you want to perform.
Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple
items.
Flick the stylus or your finger to scroll a page or a list up
and down.
4.5 Entering Information
Depending on the program you are using, you can enter information in several ways,
as described below:
Input method
Synchronizing
Typing
Drawing
Recording
Description
Use Microsoft connection management software to
exchange information between the device and a PC.
Use the Keyboard input panel to enter typed text by
clicking keys on the on- screen keyboard.
Use the stylus (like using a pen) to draw (or write) directly
on the screen.
Create a stand-alone recording or embed a recording into a
note.
22
4.5.1 Using the On-screen Keyboard
Tap the input panel button
to show the input panel as shown in figure 17.
Figure 17
Figure 18
You have two methods to input message .
When you use the keyboard, your device anticipates the word you are typing and
displays it above the Input panel. When you tap the displayed word, it is inserted into
your text at the insertion point. The more you use your device, the more words it
learns to anticipate.
To hide the input panel, tap the input panel button
again.
4.5.2 Drawing and Writing on the Screen Directly
In some applications, for example Notes, you can directly draw (or write) on the
screen using the stylus.
Tap
/ Notes shown as in figure 19, tap menu, select Draw, and then you can
write or draw directly on the screen.
23
Figure 19
4.5.3 Recording a Message
Tap
/ Notes, then tap
. To create a stand-alone recording, in the screen
displaying the list of Notes, tap the Record button
to begin recording. To add a
recording to a Note, create or open a Note and then tap the Record button
to
begin recording.
When you finish recording, tap the Stop button
. If you are creating a stand-alone
recording an icon appears in the Note list. If you are recording in an open Note an
icon appears in the Note. Tap “OK” to return to the Note list.
To play a recording tap the recording in the Note list or open the Note and then tap
the icon
in the Note.
4.5.4 Camera (Select Models Only)
Camera function built-in allows you to take photo or video in real time.
4.5.4.1 Taking Pictures
1. To start the program, press the
key on your device or tap
24
/ Pictures &
Videos/ Camera.
The Camera screen appears shown as in figure 20. Below the display area are
indicators of the current status.
Figure 20
2. For camera controls, tap “Menu” shown as in figure 21.
Figure 21
25
Menu Items
Mode
Descriptions
Three choices:
1. Normal
2. Burst- Continuous shooting of 5 pictures 3.
Timer-5 second countdown before shooting
Resolution
Three choices:
1. 640×480yv12
2. 1024×768yv2
3. 2048×1536yv12
Full Screen
Options
Full screen on or off.
Overall settings to the Camera program.
CAUTION: By default, the display area blanks out and shows the word “standby”
when the camera has been idle for one minute. To resume, tap the screen.
3. Press the
key to take the picture.
4. The result shows on the screen if the picture was taken in Normal or Timer mode.
At this time, you can tap “Menu” to perform a desired task to the current picture.
Tap “Camera” or “ok” to go back to the Camera screen.
5. The picture is saved to the predefined storage location (as long as you didn’t
delete it in the previous step).
4.5.4.2 Recording Video Clips
1. To start the program, press the
key on your device or tap
/ Pictures &
Videos/ Camera.
2. Tap Menu/ Video to switch to the video mode shown as in figure 22. Below the
display area are indicators of the current status.
26
Figure 22
3. For recording controls, tap “Menu” shown as in figure 23.
Figure 23
CAUTION: By default, the display area blanks out and shows the word “standby”
when the camera has been idle for one minute. To resume, tap the screen.
4. Press the
key to start recording. If needed, you can tap “Pause” to
temporarily pause the recording and then tap “Resume” to continue.
27
5. To stop, press the
key or tap “Stop”. Or, the recording will automatically stop
when the length reaches the pre-defined maximum value (30 seconds by default).
6. The video clip is saved to the predefined storage location. To view the video clip,
tap “Thumbnails” and choose the video you want to view.
4.6 Personal Settings
Use the controls in the Settings area to customize the device. The following examples
describe controls that are available.
4.6.1 Buttons
Use the Buttons control under Personal settings to assign the action you want to be
performed when you press the left or right application key. By default, these keys
perform the same action as the left and right tiles in the tile bar.
Tap
/ Settings/ Personal/ Buttons, open the button interface shown as in figure
24.
Figure 24
Select a button, select the action you want to occur when you press the button or
tap the soft key from the assign a program drop-down list, and then tap “OK”.
4.6.2 Home
Use the Home settings to change the display theme that controls the appearance of
28
the Home screen and to customize how items appear on the Home screen.
4.6.2.1 Appearance
You can use a theme to customize the background picture on the Home screen, the
color of the title and tile bars, menus and messages.
Tap
/ Settings/ Home/ Appearance, you can see the interface shown as in figure
25.
Figure 25
To use a predefined theme select it from the list. Select “Use this picture as the
background” check box, and then tap “Browse” to search for a file on the device. Tap
“OK” to complete the theme picture settings.
4.6.2.2 Items
You can customize which items appear on the Home screen and the order in which
they appear by the item tab.
Tap
/ Settings/ Home/ Items, you can see the interface shown as in figure 26.
29
Figure 26
Select the items to appear on the home screen and the order in which they appear,
and then tap “OK”.
4.6.2.3 Set Date and time
There are three methods as follows to open the Clock &Alarms interface:
1. Tap the clock item on the home screen.
2. Tap the tittle bar and then tap the clock icon
on the pull-down list.
3. Tap
/ Settings / Clock &Alarms.
Tap “Time” tab as shown in figure 27.
30
Figure 27
Set the required hours, minutes, seconds from the drop-down list then.
4.6.3 Screen Lock
Tap the Screen Lock icon
on the Start screen to lock the screen and keypad while
the device remains turned on. After that you can see the interface shown as in figure
28.
Figure 28
Slide the unlock icon
to unlock.
4.6.4 Set Passwords
It is possible to keep your data secure by requiring a password each time the
handheld is turned on, tap
/ Settings / Lock to set a password or to change
password settings shown as in figure 29.
31
Figure 29
You can set password and hint by taping “Password” tab and “Hint” tab.
4.6.5 Power
There are two methods as follows to open the power control:
1. Tap the tittle bar and then tap the power icon
2. Tap
on the pull-down list.
/ Settings/ System/ Power.
You can see the dialog box shown as in figure 30.
Figure 30
Figure 31
32
Tap “Battery” tab to check the battery level. Tap “Advanced” tab shown as in figure
31 to set the time before the device turns off when idle.
4.6.6 Sounds and Notifications
Use the Sounds & Notifications control set preferences for the speaker volume and
system sounds.
Tap
/ Settings/ Sounds & Notifications, tap “Sounds” tab shown as in figure 32 to
set the sounds of the event.
Figure 32
Figure 33
Tap “Notifications” tab shown as in figure 33 to set the Ring type and Ring tone of
the event.
4.6.7 Screen
Use the Screen interface to align the touch screen or to change the appearance of
text on the screen.
Tap
/ Settings/ System/ Screen, tap “General” tab. It’s shown as in figure 34. Select
an option in the orientation group to change the screen orientation, and then tap
“OK”.
33
Figure 34
Figure 35
Tap “Text Size” tab shown as in figure 35 and drag the slider control to change the
size of the text, tap “OK”.
4.6.8 Backlight
The backlight makes the screen easier to read in low light but uses extra power. Use
the Backlight control to configure power-saving settings for the backlight.
Tap
/ Settings/ System/ Backlight shown as in figure 36 to set the time before the
device turns off the backlight when idle.
Figure 36
Figure 37
34
Unselect “Turn off backlight if device is not used for”, then the device won’t turn off
the backlight when idle.
Tap “Brightness” shown as in figure 37 to change the brightness of the device.
4.6.9 Align Screen
Whenever the screen doesn’t respond to the stylus or your finger, you should align
the screen.
Tap
/ Settings/ System/ Screen shown as in figure 38 and tap “Align Screen” tab
shown as in figure 39.
Figure 38
Figure 39
Tap the target to align the screen, the device will exit the align interface automatic
after the screen is aligned.
4.7 GPRS Network Setting
Use GPRS to connect the internet, you can receive and send messages through the
network. You need to apply for GPRS Service from your service provider, and you can
search the rate of the GPRS provided by the service provider. Please contact with
your service provider to specifically know the rate of GPRS and the tariff standard
4.7.1 Add New GPRS Connecting
1. Tap
/ Settings/ Connections. It’s shown as in figure 40.
35
Figure 40
Figure 41
2. Choose “advanced” as shown in figure 42, tap “select networks” in advanced page.
Remarks: if internet had been set, you can turn to step 5.
3. Choose “My ISP” in drop-down box and click “Ok” to return to figure 37 and then
click the “tasks” tag in the upside as shown in figure 42.
Figure 42
Figure 43
4. Tap “Add a new modem connection” as shown in figure 43.
5. In “select a modem” choose “cellular line (GPRS)” and then click the next step
shown as in figure 44. Input the name of access point “CMNET”.
36
Figure 44
Figure 45
Tap “Next” as shown in figure 45, it’s not need to fill User name, Password and
Domain. Tap “Finish”.
CAUTION: Please confirm GPRS connecting is on and has established connection
before you use the GPS to measure.
4.8 Bluetooth Connecting
Tap
/ Settings/ Bluetooth as shown in figure 46.
Figure 46
37
Tap “Add new device” and select the specified Bluetooth device. Tap “Next” to input
password (default password is 1234) as shown in figure 47, tap “Next”, and then tap
“OK”.
Figure 47
Figure 48
Back to Bluetooth main screen, select “COM ports”. Choose “New Outgoing Port”.
Confirm the device SN and then click “Next”. Choose port (you can use COM0, COM4,
COM7, COM8) as show in figure 48, and then “click finish”.
CAUTION: To delete the port matched before when we are using Bluetooth, the right
operation method is delete it first in the matching port, and then delete the specific
device in the “disconnected”. It will bring inconvenience to use if you do in an
improper order.
4.9 Phone and Text Messages (Select Models Only)
4.9.1 Phone
4.9.1.1 About Your Phone
Select models are equipped with the HSDPA (High-Speed Downlink Packet Access)
module. HSDPA is an enhanced 3G (third generation) mobile telephony
communications protocol. It can operate on 850/900/1800/1900/ 2100MHz.
To use the phone, you need to first set up an account with a mobile phone network
service. The functions available to you depend on the services offered by your mobile
phone network service provider and your type of subscription.
Your service provider will provide you with a SIM card. This card contains your mobile
phone account details and rights, contacts that can be stored and any additional
38
services to which you have subscribed. You must install a SIM card before you can
make or receive phone calls or use wireless data services.
4.9.1.1.1 Switching on or off the Phone
When the device is turned on, the phone is switched on by default. When needed
(for example, on an airplane), you can switch off the phone without turning off your
device.
1. Tap
/ Settings/ Connections/ Wireless Manager, or tap the tittle bar, tap
connectivity indicator
on the pull-down list, and then tap “Wireless Manager”.
2. Appear the screen as shown in figure 49.
Figure 49
Tap “Phone” to switch it from off to on.
3. When the phone is switched on, you may be requested to enter the PIN (Personal
Identification Number) code if it has been set.
Then, your device will search for the mobile phone network service and show the
name in the Wireless Manager section on the Today screen.
Tap “Phone” again if you want to turn it off, then the Phone section displays Phone
off.
4.9.1.1.2 Starting the Phone Program
Start the Phone program by any of the three methods:
39
1. Press the Send key on the device.
2. Tap Phone (left soft key) on the Today screen.
3. Tap
/ Phone.
CAUTION: if the phone is currently off, you will be asked to turn it on.
Whenever you start Phone, the Phone screen displays the soft keypad. You can tap
Hide Keypad (left soft key).
You can use other programs during a call. To quickly switch back to Phone, press the
Send key on your device.
4.9.1.1.3 Phone Status Icons
Icons will be displayed on the navigation bar to indicate the status of the phone
functions. They are listed below:
Icon
Meaning
Icon
Phone off (airplane
mode)
Meaning
EDGE available
WCDMA/UMTS
available
WCDMA/UMTS in use
HSPA available
HSPA in use
Missing SIM card
EDGE in use
Signal strength
Call in progress
Missed call
Call on hold
GPRS available
GPRS in use
4.9.1.2 Making a Call
4.9.1.2.1 Dialing a Call
1. When on the Today screen: Press the numeric keys on your device to start entering
the phone number. Your device will automatically switch to the Phone program.
While in the Phone program: Enter the phone number using the physical or onscreen
keypad.
2. As you enter the phone number, the program searches Contacts, Call History, and
Speed Dial to find a matching name and/or number. When you see the name of the
person to call listed, select it and the desired phone number.
Or, you can continue entering the complete phone number.
3. Press the Send key on your device to make the call.
40
CAUTION:
 If you enter a wrong number, use the Backspace key to eraser individual
numbers one at a time.
 If you are making an international call, tap and hold on the number key 0 until +
sign appears. The + sign replaces the international prefix of the country from
where you are calling.
4.9.1.2.2 Making a Call From the Onscreen List
Whenever you start the Phone program, the screen lists all recent calls, speed dials,
and contacts.
If the list contains the number you want to call, you can conveniently select from the
list and press the Send key on your device.
CATION: To view a different list on the phone screen, tap menu/ view and select one
of the options.
4.9.1.2.3 Making a Call From Contacts
Microsoft Contacts displays your contact information stored both in your device’s
memory and on your SIM card.
1. Start the Contacts program.
2. Do one of the followings to call a person in the contact list:
① Tap the contact to call. Then tap the number to call; or move to the number to
call and then tap Call or press the Send key.
② Tap and hold on the contact to call, and then tap the number to call in the
shortcut menu.
4.9.1.2.4 Making a Call From the Call History List
The Call History list displays the calls you made, received or missed.
1. While in the Phone program, tap “Call History”.
If have hidden the keypad, tap Keypad to see the Call History key.
2. Do one of the followings to call a person in the Call History list:
① Select the number to call and then tap “Call” or press the Send key on your
device.
② Tap and hold on the number to call and then tap “Call” in the shortcut menu.
4.9.1.2.5 Making a Call From Speed Dial
If you have created speed dial entries, you can call a person quickly.
41
When on the Today screen or in the Phone program, press and hold the numeric key
of the assigned speed dial number to make the call.
4.9.1.3 Responding to a Call
When an incoming call is received, your device rings or vibrates according to the
options you have set for the phone. The name and number of the caller are displayed
on the pop-up window. If the name of the caller is not in your contact list, only the
caller’s phone number is displayed.
4.9.1.3.1 Answering a Call
To answer an incoming call, press the Send key on your device or tap Answer (left
soft key).
4.9.1.3.2 Rejecting a Call
To reject an incoming call, press the End key on your device or tap Ignore (right soft
key).
4.9.1.3.3 Ending a Call
To end a call, press the End key on your device or tap End on the screen.
4.9.1.4 Operations During a Call
4.9.1.4.1 Adjusting the Phone Volume
To adjust the volume during a call, tap the
volume level.
icon on the navigation bar and select a
4.9.1.4.2 Using the Mute Function
During a call, you can mute your microphone so that the person with whom you are
speaking cannot hear you, but you can still hear him or her.
On the Phone keypad, tap “Mute” to switch on the mute function. The icon will
appear on the upper-right corner. To switch off the mute function, tap “Unmute”.
42
4.9.1.4.3 Using the Speakerphone
Tap “Speaker” On to switch on the speakerphone function. The icon will appear on
the navigation bar.
To switch off the speakerphone function, tap “Speaker Off”.
4.9.1.4.4 Managing More Than One Call
CAUTION: You may need to register for the “call waiting” service with your mobile
phone network service and set your device accordingly. The exact number of people
you can talk at the same time depends on your mobile phone network service.
During a call, you can make or take a second call while putting the current call on
hold. Then, you can choose to swap between the two callers or set up a conference
call between all three parties.
Holding a Call to Take a Second Call
1. If there is another incoming call when you are talking on your device, a pop-up
window appears to notify you.
2. Tap “Answer” to place the first call on hold, and answer the second call.
3. To end the second call and go back to the first, tap “End”.
Rejecting the Second Call
To reject the second call and keep your current call in progress, tap Ignore. Be careful
not to tap End; doing so will end the current call.
Placing a Call on Hold to Make a Second Call
1. During a call, tap “Hold” to place the first call on hold.
2. Dial a second number or the first few letters of the second contact’s name by using
the numeric keypad on your device. Then press the Send key to connect. Wait for it
to be picked up.
3. To end the second call and go back to the first, tap “End”.
Swapping Between Calls
When you have put a call on hold and made or taken another call as described earlier,
you can swap between the two calls by tapping “Swap”.
Setting up a Conference Call
CAUTION: You may need to consult your mobile phone network service for the
availability and subscription of the conference call function.
1. When you have put a call on hold and made or taken another call as described
earlier, you can set up conference calling by tapping Menu/ Conference.
2. To add additional people to your conference, tap Hold. Dial a second number and
press the Send key to connect. Wait for it to be picked up. Then tap Menu/
Conference.
43
3. If you want to talk to one of the parties privately during the call, tap Menu/ Private.
Select a number, and tap “Private”.
4.9.1.4.5 Taking a Note During a Call
You can take a note during a call.
1. Tap “Notes”.
2. Enter your note and tap “ok”.
To access a note you created during a call:
1. While in the Phone program, tap “Call History”.
2. The
icon indicates that the phone call entry contains a note. Tap and hold the
name or number for that entry, and tap “View Note” in the shortcut menu.
CAUTION: You can also tap “Programs”, “Notes”, and access the note in the Calls
folder.
4.9.1.5 Using Call History
Call History provides the time and duration of all incoming, outgoing, and missed
calls, and a summary of total calls. Call History also provides easy access to any notes
taken during a call.
To access Call History while in the Phone program, tap “Call History”.
4.9.1.5.1 Viewing Call History
You can tap Menu/ Filter to change the Call History view (All Calls by default).
All Calls: Displays all calls made to and from your device in a chronological order.
Missed: Displays only calls that were not answered.
Outgoing: Displays only calls made from your device.
Incoming: Displays only calls made to your device.
To see the time, date and duration of a call, tap the item on the list to view details.
To clear all items on the list, tap Menu/ Delete All Calls.
4.9.1.5.2 Adding an Entry to Contacts Using Call History
You can add a phone number in the Call History to Outlook Contacts or SIM Contact.
1. Tap and hold the entry you wish to transfer, and tap Save to Contacts in the
shortcut menu.
2. Tap New Contact and select a contact type.
3. Enter the contact’s name, and select the proper number type.
44
Using the Phone is selected Models Only.
4. Tap “Save” to save the entry.
4.9.1.6 Using Speed Dial
You can create Speed Dials for frequently-called phone numbers so you can dial a
number with a single key press.
4.9.1.6.1 Creating a Speed Dial Entry
Speed dials can only be created for numbers stored in Contacts.
1. While in the Phone program, tap “Speed Dial”.
2. Tap Menu/ New.
3. Tap the desired contact.
4. In Name, accept the current name or change it if you want to.
5. In Number, select the phone number if there is more than one number for the
contact.
6. If Location, accept the current speed dial number or change the number if you
want to.
7. Tap “ok” to save the setting.
The new Speed Dial entry is now on the Speed Dial list. The letter on the lower-right
corner of the entry indicates the assigned phone number. For example, ‚m‛ indicates
the mobile phone number.
4.9.1.6.2 Editing or Deleting a Speed Dial Entry
1. While in the Phone program, tap “Speed Dial”.
2. Tap the desired entry and tap Delete or Tap and hold on the desired entry, and tap
“Delete” in the shortcut menu. (Select Models Only)
3. Tap “Yes”.
4.9.1.7 Customizing Your Phone
To access the Phone Settings, start the Phone program and tap Menu/ Options.
4.9.1.7.1 Changing Phone Settings
Tap “Phone” tab.
You can customize phone settings, such as the ring type and ring tone to be used for
incoming calls, and the keypad tone to be used when entering phone numbers.
45
CAUTION: To use custom .mp3, .wav or .mid files as ring tones for incoming calls,
copy the files to the Application data/ Sounds folder on your device or to the inserted
storage card. Then, select the sound from the Ring Tone list.
4.9.1.7.2 Changing Security Settings
Tap “Security” tab.
You can protect your phone from unauthorized use.
You might be prompted to enter the PIN2 code for specific functions (such as the
pre-paid card’s charging counters). Consult your mobile phone network service to
check if your SIM card supports PIN2-related functions and services.
CAUTION: Emergency call can be placed at any time without requiring a PIN code.
4.9.1.7.3 Changing Services Settings
Tap “Services” tab.
You can access and configure settings for the phone services you subscribed to
through your mobile phone network service. For example, you may want to block
certain types of incoming and/or outgoing calls, forward incoming calls to a different
phone number based on your situation, be notified of incoming calls when you are
already in a call, or let others know your identity when making calls. Services
available to you depend on your mobile phone network service and the type of your
subscription.
To view your services settings, tap a service and then tap “Get Settings”.
4.9.1.7.4 Changing Network Settings
Tap “Network” tab.
You can view available wireless networks, determine the order in which your phone
accesses another network if the current one is unavailable, and specify whether you
want to change networks manually or automatically. The current network will remain
active until you change it, lose your signal, or change your SIM card.
4.9.1.8 Additional Phone Operations
4.9.1.8.1 Using Text Messages
Text messages are automatically received when your phone is switched on. The
Today screen shows if there are new text messages. You can tap the section to open
the message list.
46
To send a text message, you can do one of the followings:
① Select a phone number from a program such as Phone or Contacts at first.
Then select “Send Text Message” from the shortcut menu or soft key.
② Start the Messaging program at first. Then select the phone number.
4.9.1.8.2 Setting up an Internet Connection
You can set up an Internet connection using the mobile network.
4.9.1.8.3 Checking Your Voice Mail
The first position in your speed dial list defaults as your voice mailbox. When you
insert your SIM card, your device automatically detects your voice mailbox number
and sets it to the first position in your speed dial list.
4.9.1.8.4 Making an Emergency Call
You can use your device to dial the international emergency number 112. This
number can normally be used to make an emergency call in any country with or
without a SIM card inserted, as long as you are within a mobile phone network.
Some mobile phone network services may require that a SIM card be inserted, and in
some cases that the PIN be entered.
There may be other emergency numbers available. Your mobile phone network
service may save additional local emergency numbers in the SIM card.
4.9.1.8.5 Dialing an International Call
When you are manually dialing a number, tap and hold on the number key 0 until the
+ sign appears. The + sign replaces the international prefix of the country from where
you are calling.
Enter the full phone number you want to dial including country code, area code
(without the leading area code zero) and local phone number.
4.9.2 Text Messages
4.9.2.1 Reading Text Messages
Text messages are automatically received when your phone is switched on. The
Today screen shows if there are new text messages. You can tap the section to open
the message list.
To manually open the message list:
1. Tap
/ Text.
47
2. The message list appears. Select the item you want to read.
4.9.2.2 Composing and Sending a Text Message
1. Tap
/ Text.
2. Tap Menu/ New.
CAUTION: You can also send a text message by selecting a phone number from
another program such as Contacts or Phone. Then select “Send text message” from
the shortcut menu or soft key.
3. Enter the phone number of one or more recipients, separating them with a
semicolon.
To select phone numbers from Contacts, tap “To”.
4. Enter your message.
To quickly add common messages, tap Menu/ My Text, and tap a desired message.
5. Tap “Send”.
4.10 WIFI Connecting
4.10.1 Switching On or Off the Wi-Fi Radio
By default, the Wi-Fi radio is switched off. To switch on or off the Wi-Fi radio:
1. Tap the Wireless Manager section on the Today screen or tap the connectivity
indicator on the navigation bar and tap “Wireless Manager”.
2. In the Wireless Manager screen, tap Wi-Fi to change the Wi-Fi radio status.
When switched on, your device will display the word Available if wireless networks
are detected.
If you have previously connected to a wireless network, your device will try to
connect to the same network and display the name of the network after the
connection.
4.10.2 Connecting to a Wireless Network
1. Switch on the Wi-Fi radio. (See ‚Switching On or Off the Wi-Fi Radio‛ previously.)
2. Your device will detect available Wi-Fi networks.
If more than one network is detected, the screen will display a network list. Select
the network you want to connect to, and tap “OK”.
3. Select to connect to the Internet or the private network, and then tap “Connect”.
4. If the selected network requires a network key, enter the key and tap “Connect”.
The WIFI icon
appears on the navigation bar.
48
CAUTION: You can also search for a network to connect by tapping
/ Settings/
Connections/ Wi-Fi.
Once you have connected to a network, the shortcut is created in Settings. Tap
/
Settings/ Connections/ Wi-Fi to change the network settings. Tap the desired
network and change the settings.
5. When you have finished using the wireless network, end the Wi-Fi connection by
switching off its radio.
CAUTION: Leaving the radio on will consume more power.
49
Chapter 5 Software Operation
You can install programs you need on the device except Pre-installed programs.
5.1 Installing Programs
1. Download the programs you need or copy them directly from the CD to your
computer.
2. Connect your device and computer, and copy the installation program to your
device when you have established the connection between your device and your
computer. Find the program you want in the File Explorer and run it. Install the
program following the instruction and select the installation path customizing. The
system will automatically generate a shortcut when the installation has successfully
completed. Click the shortcut to run the program.
CAUTION: If the system prompts to restart the device when the installation has
successfully completed, follow the prompts.
5.2 Uninstalling Programs
Tap
/ Settings/ System/ Remove Programs and select the program you want to
uninstall, tap “Remove” to accomplish the operation.
50
Chapter 6 Troubleshooting and Maintenance
This chapter gives solutions to common device problems you may encounter. It also
provides guidelines on taking care of your device.
If you have any questions, please contact with technical personnel.
6.1 Troubleshooting
Problem
Solution
Power does not switch on when using
battery power.
The remaining battery power may be too low to run
your device. Charge the battery.
Screen responds slowly.
Make sure that your device is not running out of
battery power. If the problem still persists, restart
your device.
Screen freezes.
Restart your device.
Make sure that your device and your computer are
both switched on before trying to establish a
connection.
Make sure that the cable is securely plugged into the
USB port on your computer and on your device.
Connect the USB cable directly to your
computer—do not run the cable through a USB hub.
Cannot establish a connection with a
computer via USB.
Restart your device before connecting the cable.
Always disconnect your device before you restart
your computer.
In some specific cases, your device may experience
connection problems when it is connected to a
Windows computer running ActiveSync. To resolve
the problems, please tap
/ Settings/
Connections/ USB to PC, and then clear “Enable
advanced network” functionality.
Delete files you no longer need.
Remove programs you no longer need.
Delete all files and clear history in Internet Explorer.
A warning message of not enough
memory appears.
Stop programs you are not currently using. To check
the state of your active programs, tap
System/ Task Manager.
Restart your device.
51
/ Settings/
6.2 Resetting Your Device
In some cases, you may need to restore your device to the factory default state by
clearing the memory. For example, you should clear the memory when the device
can’t be turned off, start or when you forget your password.
Clearing the memory means all data you have entered in your device’s memory,
including all files, system settings and additional programs you have installed, will be
erased. (Programs installed to ROM at the factory are not affected.)
CAUTION: To ensure the integrity of your data should it be necessary to clear the
memory, you are advised to regularly back up your data.
You can do one of the followings to upgrade:
1. Please consult the aftermarket Technical support or factory technician to ensure
the upgrade files are correct and latest.
2. Upgrade BOOT: Press and hold the power button, number keys 4 and 7 when your
device is off until the screen appears upgrade BOOT. Restart your device when the
upgrade has successfully completed.
3. Upgrade OS: Press and hold the Power button, number key 4 and “*” until the
screen appears upgrade OS. The upgrade process takes a few minutes, please be
patient.
6.3 Caring for Your Device
Taking good care of your device will ensure trouble-free operation and reduce the
risk of damage to your device.
 Keep your device away from extreme temperatures and excessive moisture.
 Avoid exposing your device to direct sunlight or strong ultraviolet light for
extended periods of time.
 Do not place anything on top of your device or drop objects on your device.
 Never privately attempt to disassemble, repair or make any modifications to
your device.
 Do not store or carry flammable liquids, gases or explosive materials in the same
compartment as your device, its parts or accessories.
52
Appendix 1: Specifications
Model
Physical specification
Operation System
Processor
RAM
P7M
P7H
Windows Mobile6.5
Marvell PXA-310 806MHz Xscale
256MB
Internal storage
4G+256MB(up to 32G)
Extended storage
TF card up to 32G
Weight
Size
P7C
550g(with internal battery)
177*91*33mm
Camera
5,000,000 pixels, VGA resolution video capture
Button
Full digital versatile physical keyboard
Sensor
Comes with electronic compass(optional)
Screen
Color TFT transflective screen
-
Display
Resolution
480×640VGA
Screen size
3.7 inch
Power supply
Battery
Working time
Communication
Wireless
Bluetooth device
1500mAh high capacity Lithium battery, Voltage 7,4V;
6 hours
802 11b/g wireless WLAN
2.1+EDR version
Communication module
USB ,OTG(connect PC with USB)
RFID
Communication module
13.56MHZ
Global Universal Quad Band Module/3.5G
Operating environment
Waterproof/Dustproof
IP65(optional IP67), protected from temporary immersion
Operating temperature
Storage temperature
Humidity
Drop
-
-20℃ to +60℃
-30℃ to +70℃
5% -95% non-condensing
1.5m concrete floor plywood fall without injury
Receiver
Chipset
Satellite System
Channels
Accuracy
Update rate
TTFF
Protocol
U-blox6
-
GPS-L1(C/A),SBAS
-
50
-
1-3m
1HZ
-
25S
NEMA-0183; Support RTCM2.1, 2.3 Difference; CORS;
-
Regional Reference Station VRS/NRS
53
-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising