Front Drive System
General Safety Information
Specifications
• Use neutral detergent to clean the chain. Do not use alkali-based or acid based detergent such as rust cleaners as it may
result in damage and/or failure of the chain.
• Use the reinforced connecting pin only for connecting the narrow type of chain.
• There are two different types of reinforced connecting pins available. Be sure to check the table below before selecting
which pin to use. If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting pin or tool
which is not suitable for the type of chain is used, sufficient connection force may not be obtained, which could cause the
chain to break or fall off.
Chain
Reinforced connecting pin
9-speed super narrow
chain such as
CN-7701 / CN-HG93
8- / 7- / 6-speed narrow
chain such as
CN-HG50 / CN-IG51
Chain tool
TL-CN32 / TL-CN23
Silver
6.5mm
Model number
Gears
SL-TX50-L
SL-TX50-LN / TX30-LN
SIS 3 - gears
Non SIS
Gear teeth should
come within this
range
1 - 3 mm
Pro-Set gauge
Model number
FD-C051/C050
FD-TY30
FD-TY10
FD-TZ31/TZ30
Front derailleur installation
band diameter (Normal type)
S, M, L
S
S, M
S, M
Front derailleur installation
band diameter (Top route type)
S, M, L
S, M
S, M
Chainstay angle (a)
66°-69°
66°-69°
66°-69°
63°-66°
66°-69°
Cut off the excess length of inner cable and then install the inner end cap.
< FD-C051 / FD-C050 >
Model number
FC-TX71
Front chainwheel tooth combination
Crank arm length
Pedal thread dimensions
Bottom bracket cup thread dimensions
Applicable front derailleur
FC-TY33
FC-TX70
48T-38T-28T
1 - 3 mm
42T-34T-24T
170mm
170mm
BC 9/16" X 20 T.P.I. (English thread)
BC 9/16" X 20 T.P.I. (English thread)
BC 1.37" X 24 T.P.I. (68, 73 mm)
BC 1.37" X 24 T.P.I. (68, 73 mm)
FD-C051
Install so that there is 1 -3 mm of
clearance at the closest point between
the largest chainring and the bottom
edge of the chain guide.
FD-C051/TY30/TZ31
FD-C050
5 mm allen key
directly above and parallel to the largest chainring.
4. Top adjustment
or a 5 mm Allen key (C051, C050).
Chain line
Spindle length
Shell width
Stamped marking
Triple
47.5mm
122.5mm
68mm
D-NL
Thread dimensions
BC1.37 X 24 T.P.I.
Tightening torque:
5 - 7 N·m {44 - 60 in. lbs.}
Gear shifting operation
Mounting the shifting lever
Smallest
sprocket
< GS >
< SL-TX50-L >
To shift from a small chainring to a larger chainring
When lever is pressed once, there is a shift of one step from
a small chainring to a larger chainring.
Largest
sprocket
Example:
from intermediate
chainring to largest
chainring.
Largest
chainring
Chain
Adjustment
When lever is pressed once, there is a shift of one step from
a large chainring to a smaller chainring.
Largest
sprocket
Pedaling becomes lighter
Be sure to follow the sequence described below.
7 / 6 - gears
7 / 6 - gears
Non SIS
Left
SL-TX50-L
SL-TX50-LN/SL-TX30-LN
SIS
SIS
FD-C051/FD-TY30
FD-C050/FD-TY10
FD-C051/FD-TZ31
FD-C050/FD-TZ30
FC-TX70/FC-TX71/FC-TY33
Bottom bracket
Chain
First remove the Pro-Set alignment block. Next,
set so that the clearance between the chain guide
inner plate and the chain is 0 - 0.5 mm.
Chain
6. Troubleshooting chart
Pro-Set alignment block
Low
adjustment
screw
Chain position
Largest
sprocket
Smallest
chainring
• Install the shifting lever in a position where it will not
obstruct brake operation and gear shifting operation.
• Do not use in a combination which causes brake
operation to be obstructed.
Chain guide inner
plate
Chain
Set so that the clearance between the
chain guide inner plate and the chain is
0 - 0.5mm.
BB-UN26
CN-UG51/CN-HG50/CN-HG40
CN-UG51/CN-HG50/CN-HG40
SM-SP18/BT18
SM-SP18/BT18
FD-TZ31 / TZ30
Front Chainwheel
Low
adjustment
screw
Chain position
Smallest
chainring
Chain
Adapter
Bottom Bracket
2. Connection and securing of cable
While firmly pulling the cable, tighten the fixing bolt with a 9 mm spanner (TY30,
TY10, TZ31, TZ30) or a 5 mm Allen key (C051, C050) to secure the cable.
G
NA
n
F
C or
h
a
i
OW
y
RRn l
o
Insert the inner cable into the outer casing from the end with the marking on it.
Apply grease from the end with the marking in order to maintain
cable operating efficiency.
Marking
Cutting the outer casing
MA
SH
SHI
NO
I MA
NO
SG
SG
E
-3
0
E-
40
This service instruction explains how to use
and maintain the Shimano bicycle parts
which have been used on your new bicycle.
For any questions regarding your bicycle or
other matters which are not related to
Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
Tightening torque:
35 - 50 N·m {305 - 435 in. lbs.}
When cutting the outer casing, cut the opposite end to the
end with the marking. After cutting the outer casing, make
the end round so that the inside of the hole has a uniform
diameter.
Attach the same outer end cap to the
cut end of the outer casing.
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English)
© Sep. 2006 by Shimano Inc. XBC SZK Printed in China.
Securely tighten
Tighten the top adjustment screw
clockwise (about 1/4 turn).
If shifting is difficult from the
intermediate chainring to the largest
chainring
Loosen the top adjustment screw
counterclockwise (about 1/8 turn).
If shifting is difficult from the
intermediate chainring to the
smallest chainring
Loosen the low adjustment screw
counterclockwise (about 1/4 turn).
If there is interference between the
chain and the front derailleur inner
plate at the largest chainring
Tighten the top adjustment screw
clockwise (about 1/8 turn).
If there is interference between the
chain and the front derailleur outer
plate at the largest chainring
Loosen the top adjustment screw
counterclockwise (about 1/8 turn).
If the intermediate chainring is
skipped when shifting from the
largest chainring
Loosen the outer casing adjustment
barrel counterclockwise (1 or 2 turns).
*
Tighten the outer casing adjustment
barrel clockwise (1 or 2 turns).
*
If shifting is difficult from the largest
chainring to the intermediate
chainring
Tighten the low adjustment screw
clockwise (about 1/2 turn).
* SL-TX50-L
Inserting the inner cable
S
If the chain falls to the crank side
If the chain falls to the bottom
bracket side
Tightening torque: 5 - 7 N·m {44 - 60 in. lbs.}
Use the cotterless crank extractor (TL-FC10) to install the
front chainwheel.
After completion of steps 1 - 5, move the shifting lever to check the
shifting. (This also applies if shifting becomes difficult during use.)
If there is interference between the
chain and front derailleur inner plate
when the rear sprocket is shifted to
the largest sprocket when the
chainwheel is at the intermediate
chainring position.
Chain guide inner
plate
Tightening torque:
50 - 70 N·m {435 - 608 in. lbs.}
Chain guide
inner plate
FD-C051 / C050
FD-TY30 / TY10
Do not open the clamp of the lever when
installing, otherwise the cover may be
damaged.
Installation of the front chainwheel
BB-UN26
Bottom bracket cable guide
Outer casing
adjustment barrel
< FD-C051 / FD-C050 / FD-TY30 / FD-TY10 >
Largest
sprocket
SIS 3 - gears
Intermediate
chainring
1. Low adjustment
Example:
from largest chainring to
intermediate chainring.
< FD-TZ31 / FD-TZ30 >
Left
Set the chain onto the largest sprocket, and at the front, move the chain from
the largest chainring to the intermediate chainring. Adjust using the cable
adjusting bolt so that the clearance between the chain guide inner plate and
the chain is 0 - 0.5 mm.
Chain position
To shift from a large chainring to a smaller chainring
Installation of the bottom bracket
Right
Front chainwheel
5. Adjustment of the intermediate chainring (SL-TX50-L)
Guide pulley
Tightening torque:
2.5 Nm {22 in. lbs.}
Tourney
Front derailleur
Chain
Chain
FD-C051 / C050
Largest
chainring
Right angle to the ground
In order to realize the best performance, we recommend that the following combination be used.
Outer casing
Smallest
sprocket
Tension pulley
Install using the special tool TL-UN74.
First install the main body, then the adapter.
Series
Chain guide
outer plate
Largest
chainring
< SS >
Add 2 links (with the chain on both
the largest sprocket and the largest
chainring)
Use a handlebar grip
with a maximum outer
diameter of 32 mm.
Pedaling becomes heavier
Front Drive System
Top adjustment
screw
Chain position
< SL-TX50-LN / TX30-LN >
SI-6DK0B
FD-TY30 / TY10 /
TZ31 / TZ30
Set so that the clearance between
the chain guide outer plate and the
chain is 0 - 0.5 mm.
Chain length
Note:
Technical Service Instructions
Normal type
Chainwheel
(largest chainring)
3. Secure using a 9 mm spanner (TY30, TY10, TZ31, TZ30)
Bottom Bracket
Wire fixing bolt
Top route type
2. The level section of the chain guide outer plate should be
Chain guide
Shifting lever
Note:
Pass the cable through
as shown in the
illustration.
Chainstay angle
Front chainwheel
Type
• The reinforced connecting pins cannot be used with the UG chain, otherwise the connections will not move properly and
noise will occur.
• FD-TZ31/TZ30 are Non SIS compatible, and cannot be used in combination with the SL-TX50-L.
• Apply grease to the thread section of the bottom bracket and to the inside thread of the adapter before installing the bottom
bracket.
• In addition, if pedaling performance does not feel normal, check this once more.
• Check that there is no looseness in any joints or connections before riding the bicycle. (BB-FC, FC-PD)
• Do not wash the bottom bracket with high-pressure jets of water.
• If you feel any looseness in the bottom bracket axle, the bottom bracket should be replaced.
• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.
• You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In addition, cleaning the
chain with neutral detergent and lubricating it can be a effective way of extending the useful life of the chainrings and the
chain.
• If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.
• Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.
Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.
• Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.
• Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.
• For smooth operation, use the specified outer casing and bottom bracket cable guide.
• To ensure the best performance, be sure to use only the specified type of chain. The wide type chain cannot be used.
• For maximum performance we highly recommend Shimano lubricants and maintenance products.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional
bicycle dealer.
Pull
Pro-Set alignment block
< FD-TZ31 / FD-TZ30 >
Note
Top route type
Pull
7.1mm
Reinforced Connecting Pin
• If it is necessary to adjust the length of the chain due to a change in the number of sprocket
teeth, make the cut at some other place than the place where the chain has been joined
using a reinforced connecting pin or an end pin. The chain will be damaged if it is cut at a
place where it has been joined with a reinforced connecting pin or an end pin.
• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise
End Pin
Link Pin
you may fall off the bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is too weak or the chain is
damaged, the chain should be replaced. If this is not done, the chain may break and cause serious injury.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank arm may break
and you may fall off the bicycle.
• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn, or damaged parts may cause
injury to the rider.
We strongly recommend only using genuine Shimano replacement parts.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Gears
Normal type
Adjust and then install the front derailleur as shown in the illustration. Do not
remove the Pro-Set alignment block at this time.
Front Derailleur
TL-CN32 / TL-CN23
Black
After taking up the initial slack in the cable, re-secure to the front derailleur as
shown in the illustration.
1. < FD-C051 / FD-C050 / FD-TY30 / FD-TY10 >
Shifting lever
WARNING
3. Adjustment of cable tension
Installation of the front derailleur
Outer end cap
Replacing the inner cable
Operate the lever to set the chain to the first position (low), and then pass the
inner cable through.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement